Study guide

6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson)

PE Chemical Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the PE Chemical Exam How to Use This Guide and the NCEES Handbook

2 Chapter 1: Material Balances & Flowsheet Calculations

1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations

3 Chapter 2: Energy Balances & Thermochemistry

2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances

4 Chapter 3: Fluid Statics & Incompressible Pipe Flow

3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations

5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up

6 Chapter 5: Thermodynamic Laws & Fundamental Relations

5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations

7 Chapter 6: Real Gases & Equations of State

6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions

8 Chapter 7: Phase & Chemical Reaction Equilibria

7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation

9 Chapter 8: Heat Transfer Mechanisms & Conduction

8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange

10 Chapter 9: Heat Exchanger Design & Phase Change

9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances

11 Chapter 10: Mass Transfer Fundamentals & Diffusion

10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

12 Chapter 11: Distillation Operations

11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components

13 Chapter 12: Rate-Controlled & Equilibrium Separations

12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations

14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors

13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations

15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis

14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models

16 Chapter 15: Physical & Transport Properties of Fluids

15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles

17 Chapter 16: Materials of Construction & Corrosion

16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention

18 Chapter 17: Process Safety & Pressure Relief Systems

17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment

19 Chapter 18: Process Control & Engineering Economics

18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems

20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance

19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation

21 Chapter 20: Plant Operation, Reliability & Continuous Improvement

20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting

6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson)

Key Takeaways Explain This Topic AI

Cubic equations of state represent the simplest algebraic framework capable of predicting both vapor and liquid phases simultaneously across subcritical, critical, and supercritical regimes using critical constants (T_c, P_c, omega).

The van der Waals EOS (P = RT/(v-b) - a/v^2) established molecular co-volume b and attractive energy a, but its fixed critical compressibility of Z_c = 0.375 severely overestimates experimental values for real hydrocarbons (Z_c ~ 0.27-0.29).

Soave-Redlich-Kwong (SRK) and Peng-Robinson (PR) incorporate temperature-dependent attraction terms alpha(T_r, omega) calibrated to Pitzer's acentric factor, allowing accurate pure-component vapor pressure matching across reduced temperatures 0.4 <= T_r <= 1.0.

In the subcritical two-phase envelope (T < T_c, P = P_sat), a cubic EOS yields three real roots in compressibility Z: the largest root represents saturated vapor (Z_V), the smallest root represents saturated liquid (Z_L), and the middle root is mechanically unstable where (dP/dv)_T > 0.

Peng-Robinson provides superior liquid density predictions (Z_c = 0.307) compared to SRK (Z_c = 0.333), establishing PR as the chemical and petroleum industry standard for gas processing, refining, and pipeline simulation.

Last updated: September 2026

6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson)

In modern chemical engineering process design, cubic equations of state (EOS) are the workhorses of process simulators (such as Aspen Plus, HYSYS, and Pro/II) and flash calculation algorithms. On the NCEES PE Chemical Exam , questions test your conceptual mastery of cubic equation formulations, parameter dependencies on critical constants ( T c , P c , ω T_c, P_c, \omega T c ​ , P c ​ , ω ), root interpretation in two-phase regimes, and mixing rules for multi-component fluids.

A cubic equation of state is the lowest-order polynomial equation in molar volume ( v v v ) or compressibility factor ( Z Z Z ) capable of describing both the liquid phase and the vapor phase , as well as the continuity between them through the critical point.

1. Mathematical Architecture of Cubic Equations of State

All two-parameter cubic equations of state can be expressed in a unified pressure-explicit form: P = R T v − b − a ( T ) ( v + ϵ b ) ( v + σ b ) P = \frac{R T}{v - b} - \frac{a(T)}{(v + \epsilon b)(v + \sigma b)} P = v − b RT ​ − ( v + ϵ b ) ( v + σb ) a ( T ) ​

Where:

R T v − b \frac{R T}{v - b} v − b RT ​ is the repulsive pressure term , representing hard-sphere molecular collisions and molecular co-volume ( b b b ).

a ( T ) ( v + ϵ b ) ( v + σ b ) \frac{a(T)}{(v + \epsilon b)(v + \sigma b)} ( v + ϵ b ) ( v + σb ) a ( T ) ​ is the attractive pressure term , representing intermolecular cohesive forces ( a a a ).

b b b = effective molar volume of the molecules themselves ( m 3 / mol \text{m}^3/\text{mol} m 3 / mol or ft 3 / lbmol \text{ft}^3/\text{lbmol} ft 3 / lbmol ).

a ( T ) a(T) a ( T ) = measure of intermolecular attractive force strength ( Pa ⋅ m 6 / mol 2 \text{Pa}\cdot\text{m}^6/\text{mol}^2 Pa ⋅ m 6 / mol 2 or psia ⋅ ft 6 / lbmol 2 \text{psia}\cdot\text{ft}^6/\text{lbmol}^2 psia ⋅ ft 6 / lbmol 2 ).

ϵ , σ \epsilon, \sigma ϵ , σ = pure numerical constants specific to each equation family.

The Critical Point Inflection Constraints

To determine the parameters a a a and b b b for any cubic equation of state, we apply the mathematical conditions of the critical isotherm at the critical point ( T = T c , P = P c , v = v c T = T_c, P = P_c, v = v_c T = T c ​ , P = P c ​ , v = v c ​ ). At this unique point, the liquid and vapor phases become indistinguishable, producing a horizontal inflection point: ( ∂ P ∂ v ) T = T c = 0 \left( \frac{\partial P}{\partial v} \right)_{T = T_c} = 0 ( ∂ v ∂ P ​ ) T = T c ​ ​ = 0 ( ∂ 2 P ∂ v 2 ) T = T c = 0 \left( \frac{\partial^2 P}{\partial v^2} \right)_{T = T_c} = 0 ( ∂ v 2 ∂ 2 P ​ ) T = T c ​ ​ = 0

Solving these two simultaneous differential constraints alongside P ( T c , v c ) = P c P(T_c, v_c) = P_c P ( T c ​ , v c ​ ) = P c ​ uniquely determines the parameter scaling constants Ω a \Omega_a Ω a ​ and Ω b \Omega_b Ω b ​ , as well as the theoretical critical compressibility factor Z c = P c v c / ( R T c ) Z_c = P_c v_c / (R T_c) Z c ​ = P c ​ v c ​ / ( R T c ​ ) .

  • 2. Systematic Derivation: From van der Waals to Peng-Robinson
  • 1. van der Waals (vdW, 1873)

The historical foundation of real fluid thermodynamics: P = R T v − b − a v 2 ( ϵ = 0 , σ = 0 ) P = \frac{R T}{v - b} - \frac{a}{v^2} \quad (\epsilon = 0, \sigma = 0) P = v − b RT ​ − v 2 a ​ ( ϵ = 0 , σ = 0 )

Applying the critical inflection conditions yields: a = 27 R 2 T c 2 64 P c = 0.42188 R 2 T c 2 P c a = \frac{27 R^2 T_c^2}{64 P_c} = 0.42188 \frac{R^2 T_c^2}{P_c} a = 64 P c ​ 27 R 2 T c 2 ​ ​ = 0.42188 P c ​ R 2 T c 2 ​ ​ b = R T c 8 P c = 0.12500 R T c P c b = \frac{R T_c}{8 P_c} = 0.12500 \frac{R T_c}{P_c} b = 8 P c ​ R T c ​ ​ = 0.12500 P c ​ R T c ​ ​ Z c = 3 8 = 0.37500 Z_c = \frac{3}{8} = 0.37500 Z c ​ = 8 3 ​ = 0.37500

Flaws : The universal critical compressibility of Z c = 0.375 Z_c = 0.375 Z c ​ = 0.375 is far too high for real substances (hydrocarbons typically have Z c ≈ 0.26 − 0.29 Z_c \approx 0.26 - 0.29 Z c ​ ≈ 0.26 − 0.29 ; water is 0.229 0.229 0.229 ). Consequently, vdW severely underpredicts liquid densities (overpredicts liquid volumes by 30 − 50 % 30-50\% 30 − 50% ) and cannot accurately match pure-component vapor pressures across wide temperature ranges.

2. Redlich-Kwong (RK, 1949)

Otto Redlich and Joseph N. S. Kwong introduced a temperature-dependent attraction term proportional to T − 0.5 T^{-0.5} T − 0.5 and modified the volume denominator: P = R T v − b − a T v ( v + b ) ( ϵ = 0 , σ = 1 ) P = \frac{R T}{v - b} - \frac{a}{\sqrt{T} v(v + b)} \quad (\epsilon = 0, \sigma = 1) P = v − b RT ​ − T ​ v ( v + b ) a ​ ( ϵ = 0 , σ = 1 ) a = 0.42748 R 2 T c 2.5 P c a = 0.42748 \frac{R^2 T_c^{2.5}}{P_c} a = 0.42748 P c ​ R 2 T c 2.5 ​ ​ b = 0.08664 R T c P c b = 0.08664 \frac{R T_c}{P_c} b = 0.08664 P c ​ R T c ​ ​ Z c = 1 3 ≈ 0.33333 Z_c = \frac{1}{3} \approx 0.33333 Z c ​ = 3 1 ​ ≈ 0.33333

Significance : RK significantly improved vapor phase properties and gas-mixture PVT predictions over vdW. However, it still overpredicts Z c Z_c Z c ​ ( 0.333 0.333 0.333 vs actual 0.27 0.27 0.27 ) and remains inadequate for liquid-phase equilibria.

3. Soave-Redlich-Kwong (SRK, 1972)

Giorgio Soave replaced the 1 / T 1/\sqrt{T} 1/ T ​ term in Redlich-Kwong with a generalized temperature-dependent function α ( T r , ω ) \alpha(T_r, \omega) α ( T r ​ , ω ) calibrated to reproduce experimental pure-component vapor pressures at T r = 0.70 T_r = 0.70 T r ​ = 0.70 : P = R T v − b − a ( T ) v ( v + b ) ( ϵ = 0 , σ = 1 ) P = \frac{R T}{v - b} - \frac{a(T)}{v(v + b)} \quad (\epsilon = 0, \sigma = 1) P = v − b RT ​ − v ( v + b ) a ( T ) ​ ( ϵ = 0 , σ = 1 ) a ( T ) = a c α ( T r , ω ) = 0.42748 R 2 T c 2 P c α ( T r , ω ) a(T) = a_c \alpha(T_r, \omega) = 0.42748 \frac{R^2 T_c^2}{P_c} \alpha(T_r, \omega) a ( T ) = a c ​ α ( T r ​ , ω ) = 0.42748 P c ​ R 2 T c 2 ​ ​ α ( T r ​ , ω ) b = 0.08664 R T c P c b = 0.08664 \frac{R T_c}{P_c} b = 0.08664 P c ​ R T c ​ ​ α ( T r , ω ) = [ 1 + m ( 1 − T r ) ] 2 \alpha(T_r, \omega) = \left[ 1 + m \left( 1 - \sqrt{T_r} \right) \right]^2 α ( T r ​ , ω ) = [ 1 + m ( 1 − T r ​ ​ ) ] 2 m = 0.480 + 1.574 ω − 0.176 ω 2 m = 0.480 + 1.574\omega - 0.176\omega^2 m = 0.480 + 1.574 ω − 0.176 ω 2 Z c = 1 3 ≈ 0.33333 Z_c = \frac{1}{3} \approx 0.33333 Z c ​ = 3 1 ​ ≈ 0.33333

Significance : SRK marked the birth of modern industrial vapor-liquid equilibrium (VLE) modeling for hydrocarbon processing. It predicts vapor pressures with high fidelity. However, because Z c Z_c Z c ​ remains fixed at 0.333 0.333 0.333 , liquid densities are still underestimated by 10 − 15 % 10-15\% 10 − 15% .

4. Peng-Robinson (PR, 1976)

Ding-Yu Peng and Donald B. Robinson modified the attractive term denominator to yield a lower, more realistic critical compressibility factor ( Z c = 0.307 Z_c = 0.307 Z c ​ = 0.307 ): P = R T v − b − a ( T ) v ( v + b ) + b ( v − b ) = R T v − b − a ( T ) v 2 + 2 b v − b 2 ( ϵ = 1 − 2 , σ = 1 + 2 ) P = \frac{R T}{v - b} - \frac{a(T)}{v(v + b) + b(v - b)} = \frac{R T}{v - b} - \frac{a(T)}{v^2 + 2bv - b^2} \quad (\epsilon = 1 - \sqrt{2}, \sigma = 1 + \sqrt{2}) P = v − b RT ​ − v ( v + b ) + b ( v − b ) a ( T ) ​ = v − b RT ​ − v 2 + 2 b v − b 2 a ( T ) ​ ( ϵ = 1 − 2 ​ , σ = 1 + 2 ​ ) a ( T ) = a c α ( T r , ω ) = 0.45724 R 2 T c 2 P c α ( T r , ω ) a(T) = a_c \alpha(T_r, \omega) = 0.45724 \frac{R^2 T_c^2}{P_c} \alpha(T_r, \omega) a ( T ) = a c ​ α ( T r ​ , ω ) = 0.45724 P c ​ R 2 T c 2 ​ ​ α ( T r ​ , ω ) b = 0.07780 R T c P c b = 0.07780 \frac{R T_c}{P_c} b = 0.07780 P c ​ R T c ​ ​ α ( T r , ω ) = [ 1 + κ ( 1 − T r ) ] 2 \alpha(T_r, \omega) = \left[ 1 + \kappa \left( 1 - \sqrt{T_r} \right) \right]^2 α ( T r ​ , ω ) = [ 1 + κ ( 1 − T r ​ ​ ) ] 2 κ = 0.37464 + 1.54226 ω − 0.26992 ω 2 ( for ω ≤ 0.49 ) \kappa = 0.37464 + 1.54226\omega - 0.26992\omega^2 \quad (\text{for } \omega \le 0.49) κ = 0.37464 + 1.54226 ω − 0.26992 ω 2 ( for ω ≤ 0.49 ) Z c = 0.30740 Z_c = 0.30740 Z c ​ = 0.30740

Significance : Peng-Robinson is the most widely applied equation of state in petroleum refining, natural gas processing, and chemical plant simulations. Its predicted liquid molar volumes are substantially closer to experimental values than those from SRK.

3. Comparison Table: Performance Metrics of Major Cubic Equations

Equation of State ϵ , σ \epsilon, \sigma ϵ , σ Ω a \Omega_a Ω a ​ Ω b \Omega_b Ω b ​ Critical Z c Z_c Z c ​ Liquid Density Accuracy Primary Application Domain

van der Waals (vdW) 0 , 0 0, 0 0 , 0 27 / 64 = 0.42188 27/64 = 0.42188 27/64 = 0.42188 1 / 8 = 0.12500 1/8 = 0.12500 1/8 = 0.12500 0.375 0.375 0.375 Very Poor (overpredicts volume by > 35 % >35\% > 35% ) Conceptual teaching only

Redlich-Kwong (RK) 0 , 1 0, 1 0 , 1 0.42748 0.42748 0.42748 0.08664 0.08664 0.08664 0.333 0.333 0.333 Poor Moderate-pressure gas mixtures

Soave-Redlich-Kwong (SRK) 0 , 1 0, 1 0 , 1 0.42748 0.42748 0.42748 0.08664 0.08664 0.08664 0.333 0.333 0.333 Moderate ( 10 − 15 % 10-15\% 10 − 15% error) Gas processing, hydrocarbon VLE

Peng-Robinson (PR) 1 − 2 , 1 + 2 1-\sqrt{2}, 1+\sqrt{2} 1 − 2 ​ , 1 + 2 ​ 0.45724 0.45724 0.45724 0.07780 0.07780 0.07780 0.307 0.307 0.307 Good ( 4 − 8 % 4-8\% 4 − 8% error) Refining, petrochemicals, pipelines

4. Solving the Cubic Polynomial in Compressibility Factor Z Z Z

To solve for molar volume or compressibility factor on a computer or calculator, the equation of state is rearranged into a dimensionless cubic polynomial in Z Z Z ( Z = P v / R T Z = P v / R T Z = P v / RT ).

Define the dimensionless equation parameters: A ≡ a P ( R T ) 2 = Ω a P r T r 2 α ( T r , ω ) A \equiv \frac{a P}{(R T)^2} = \Omega_a \frac{P_r}{T_r^2} \alpha(T_r, \omega) A ≡ ( RT ) 2 a P ​ = Ω a ​ T r 2 ​ P r ​ ​ α ( T r ​ , ω ) B ≡ b P R T = Ω b P r T r B \equiv \frac{b P}{R T} = \Omega_b \frac{P_r}{T_r} B ≡ RT b P ​ = Ω b ​ T r ​ P r ​ ​

Substituting v = Z R T / P v = Z R T / P v = ZRT / P into each equation yields the standard cubic polynomials:

Cubic Form for van der Waals: Z 3 − ( 1 + B ) Z 2 + A Z − A B = 0 Z^3 - (1 + B)Z^2 + A Z - A B = 0 Z 3 − ( 1 + B ) Z 2 + A Z − A B = 0

Cubic Form for SRK: Z 3 − Z 2 + ( A − B − B 2 ) Z − A B = 0 Z^3 - Z^2 + (A - B - B^2)Z - A B = 0 Z 3 − Z 2 + ( A − B − B 2 ) Z − A B = 0

Cubic Form for Peng-Robinson: Z 3 − ( 1 − B ) Z 2 + ( A − 3 B 2 − 2 B ) Z − ( A B − B 2 − B 3 ) = 0 Z^3 - (1 - B)Z^2 + (A - 3B^2 - 2B)Z - (A B - B^2 - B^3) = 0 Z 3 − ( 1 − B ) Z 2 + ( A − 3 B 2 − 2 B ) Z − ( A B − B 2 − B 3 ) = 0

5. Root Selection & The Three-Root Phenomenon

When solving the cubic polynomial for a pure substance or mixture at given T T T and P P P :

Single Real Root Regime : At temperatures above the critical point ( T > T c T > T_c T > T c ​ ) or at very high pressures, the polynomial yields one real root and two complex conjugate roots. The single real root represents the fluid state (supercritical fluid, dense gas, or compressed liquid).

Three Real Roots Regime : In the subcritical two-phase region ( T < T c T < T_c T < T c ​ ) at pressures corresponding to the two-phase envelope, the polynomial yields three real roots : Z L < Z M < Z V Z_L < Z_M < Z_V Z L ​ < Z M ​ < Z V ​

Largest Root ( Z V Z_V Z V ​ ) : Corresponds to the vapor phase (highest molar volume, lowest density). This root is selected for superheated vapor, saturated vapor, or flash vapor streams.

Smallest Positive Root ( Z L Z_L Z L ​ ) : Corresponds to the liquid phase (lowest molar volume, highest density). This root is selected for subcooled liquid, saturated liquid, or flash liquid streams.

Intermediate Middle Root ( Z M Z_M Z M ​ ) : Has no physical reality . It corresponds to the mechanically unstable region of the isotherm where ( ∂ P / ∂ v ) T > 0 (\partial P / \partial v)_T > 0 ( ∂ P / ∂ v ) T ​ > 0 . In this unphysical region, an increase in pressure would cause an increase in volume, violating the Second Law of Thermodynamics. It is discarded in engineering calculations. P ^

  • | Subcritical Isotherm
  • | /---\ (Z_L)
  • | / \ /---
  • P_sat-------(L)-------(M)-----------(V)-------
  • | / \ /
  • | / \-------/ (Z_V)
  • +----------------------------------------> v
  • v_liquid v_unstable v_vapor
  • 6. Multicomponent Mixing Rules: van der Waals One-Fluid (vdW1f)

To apply cubic equations of state to multicomponent gas or liquid mixtures, effective mixture parameters a m i x a_{mix} a mi x ​ and b m i x b_{mix} b mi x ​ must be calculated from the pure-component parameters using mixing rules .

The standard industrial formulation is the van der Waals One-Fluid (vdW1f) mixing rules :

Co-Volume Parameter ( b m i x b_{mix} b mi x ​ )

Because molecular volumes are essentially additive: b m i x = ∑ i = 1 C x i b i b_{mix} = \sum_{i=1}^C x_i b_i b mi x ​ = i = 1 ∑ C ​ x i ​ b i ​

Attractive Energy Parameter ( a m i x a_{mix} a mi x ​ )

Because attractive interactions occur between pairs of colliding molecules ( i − j i-j i − j pairs): a m i x = ∑ i = 1 C ∑ j = 1 C x i x j a i j a_{mix} = \sum_{i=1}^C \sum_{j=1}^C x_i x_j a_{ij} a mi x ​ = i = 1 ∑ C ​ j = 1 ∑ C ​ x i ​ x j ​ a ij ​

Where x i x_i x i ​ is the mole fraction of component i i i (liquid or vapor), and a i j a_{ij} a ij ​ is the cross-interaction parameter between dissimilar species i i i and j j j .

Combining Rule & The Binary Interaction Parameter ( k i j k_{ij} k ij ​ )

The cross-parameter a i j a_{ij} a ij ​ is evaluated using the geometric mean combining rule, modified by an empirical binary interaction parameter ( k i j k_{ij} k ij ​ ): a i j = a i a j ( 1 − k i j ) a_{ij} = \sqrt{a_i a_j} \left( 1 - k_{ij} \right) a ij ​ = a i ​ a j ​ ​ ( 1 − k ij ​ )

k i j = k j i k_{ij} = k_{ji} k ij ​ = k ji ​ (symmetry).

k i i = 0 k_{ii} = 0 k ii ​ = 0 (interaction of a molecule with itself).

Physical Meaning : k i j k_{ij} k ij ​ accounts for differences in molecular size, polarity, and chemical nature between dissimilar molecules.

For chemically similar hydrocarbon pairs (e.g., methane + ethane, propane + butane): k i j ≈ 0.00 k_{ij} \approx 0.00 k ij ​ ≈ 0.00 .

For hydrocarbon + non-hydrocarbon pairs (e.g., CH 4 + CO 2 \text{CH}_4 + \text{CO}_2 CH 4 ​ + CO 2 ​ , CH 4 + H 2 S \text{CH}_4 + \text{H}_2\text{S} CH 4 ​ + H 2 ​ S , CH 4 + N 2 \text{CH}_4 + \text{N}_2 CH 4 ​ + N 2 ​ ): k i j k_{ij} k ij ​ typically ranges from 0.05 0.05 0.05 to 0.15 0.15 0.15 .

A positive k i j k_{ij} k ij ​ decreases the cross-attraction a i j a_{ij} a ij ​ below the geometric mean, modeling positive deviations from ideal solution behavior.

  • 7. Comprehensive Worked Numerical Example: Peng-Robinson Molar Volume and Vapor Density of Propane
  • Problem Statement

A chemical reactor feed drum stores pure propane ( C 3 H 8 \text{C}_3\text{H}_8 C 3 ​ H 8 ​ ) vapor at a temperature of T = 320.0 K T = 320.0\text{ K} T = 320.0 K ( 46.85 ∘ C 46.85^\circ\text{C} 46.8 5 ∘ C ) and an operating pressure of P = 1.50 MPa P = 1.50\text{ MPa} P = 1.50 MPa ( 15.0 bar = 1.50 × 10 6 Pa 15.0\text{ bar} = 1.50 \times 10^6\text{ Pa} 15.0 bar = 1.50 × 1 0 6 Pa ).

Physical Properties for Propane ( M W = 44.097 kg/kmol MW = 44.097\text{ kg/kmol} M W = 44.097 kg/kmol ):

Critical temperature: T c = 369.8 K T_c = 369.8\text{ K} T c ​ = 369.8 K

Critical pressure: P c = 4.248 MPa = 4.248 × 10 6 Pa P_c = 4.248\text{ MPa} = 4.248 \times 10^6\text{ Pa} P c ​ = 4.248 MPa = 4.248 × 1 0 6 Pa

Acentric factor: ω = 0.152 \omega = 0.152 ω = 0.152

Calculate:

The reduced temperature T r T_r T r ​ and reduced pressure P r P_r P r ​ .

The Peng-Robinson parameters κ \kappa κ , α ( T r , ω ) \alpha(T_r, \omega) α ( T r ​ , ω ) , a ( T ) a(T) a ( T ) , and b b b .

The dimensionless coefficients A A A and B B B .

Formulate the cubic polynomial in Z Z Z and solve for the vapor compressibility factor Z V Z_V Z V ​ .

Calculate the molar volume v v v ( m 3 / mol \text{m}^3/\text{mol} m 3 / mol and L/mol \text{L/mol} L/mol ) and mass density ρ \rho ρ ( kg/m 3 \text{kg/m}^3 kg/m 3 ).

Compare the PR result with the ideal gas law prediction.

Step 1: Reduced Coordinates T r = T T c = 320.0 K 369.8 K = 0.8653 T_r = \frac{T}{T_c} = \frac{320.0\text{ K}}{369.8\text{ K}} = \mathbf{0.8653} T r ​ = T c ​ T ​ = 369.8 K 320.0 K ​ = 0.8653 P r = P P c = 1.50 MPa 4.248 MPa = 0.3531 P_r = \frac{P}{P_c} = \frac{1.50\text{ MPa}}{4.248\text{ MPa}} = \mathbf{0.3531} P r ​ = P c ​ P ​ = 4.248 MPa 1.50 MPa ​ = 0.3531

Step 2: Peng-Robinson Parameters

Evaluate κ \kappa κ : κ = 0.37464 + 1.54226 ω − 0.26992 ω 2 \kappa = 0.37464 + 1.54226\omega - 0.26992\omega^2 κ = 0.37464 + 1.54226 ω − 0.26992 ω 2 κ = 0.37464 + 1.54226 ( 0.152 ) − 0.26992 ( 0.152 ) 2 = 0.37464 + 0.23442 − 0.00624 = 0.6028 \kappa = 0.37464 + 1.54226(0.152) - 0.26992(0.152)^2 = 0.37464 + 0.23442 - 0.00624 = \mathbf{0.6028} κ = 0.37464 + 1.54226 ( 0.152 ) − 0.26992 ( 0.152 ) 2 = 0.37464 + 0.23442 − 0.00624 = 0.6028

Evaluate α ( T r , ω ) \alpha(T_r, \omega) α ( T r ​ , ω ) : α = [ 1 + κ ( 1 − T r ) ] 2 = [ 1 + 0.6028 ( 1 − 0.8653 ) ] 2 \alpha = \left[ 1 + \kappa \left( 1 - \sqrt{T_r} \right) \right]^2 = \left[ 1 + 0.6028 \left( 1 - \sqrt{0.8653} \right) \right]^2 α = [ 1 + κ ( 1 − T r ​ ​ ) ] 2 = [ 1 + 0.6028 ( 1 − 0.8653 ​ ) ] 2 0.8653 = 0.93022 ⟹ 1 − T r = 0.06978 \sqrt{0.8653} = 0.93022 \implies 1 - \sqrt{T_r} = 0.06978 0.8653 ​ = 0.93022 ⟹ 1 − T r ​ ​ = 0.06978 α = [ 1 + 0.6028 ( 0.06978 ) ] 2 = [ 1 + 0.04206 ] 2 = ( 1.04206 ) 2 = 1.0859 \alpha = \left[ 1 + 0.6028(0.06978) \right]^2 = \left[ 1 + 0.04206 \right]^2 = (1.04206)^2 = \mathbf{1.0859} α = [ 1 + 0.6028 ( 0.06978 ) ] 2 = [ 1 + 0.04206 ] 2 = ( 1.04206 ) 2 = 1.0859

Evaluate pure component attraction parameter a ( T ) a(T) a ( T ) : a c = 0.45724 R 2 T c 2 P c = 0.45724 ( 8.31447 ) 2 ( 369.8 ) 2 4.248 × 10 6 = 0.45724 ( 69.1304 ) ( 136 , 752 ) 4.248 × 10 6 = 1.0175 Pa ⋅ m 6 / mol 2 a_c = 0.45724 \frac{R^2 T_c^2}{P_c} = 0.45724 \frac{(8.31447)^2 (369.8)^2}{4.248 \times 10^6} = 0.45724 \frac{(69.1304)(136,752)}{4.248 \times 10^6} = \mathbf{1.0175\text{ Pa}\cdot\text{m}^6/\text{mol}^2} a c ​ = 0.45724 P c ​ R 2 T c 2 ​ ​ = 0.45724 4.248 × 1 0 6 ( 8.31447 ) 2 ( 369.8 ) 2 ​ = 0.45724 4.248 × 1 0 6 ( 69.1304 ) ( 136 , 752 ) ​ = 1.0175 Pa ⋅ m 6 / mol 2 a ( T ) = a c ⋅ α = 1.0175 × 1.0859 = 1.1049 Pa ⋅ m 6 / mol 2 a(T) = a_c \cdot \alpha = 1.0175 \times 1.0859 = \mathbf{1.1049\text{ Pa}\cdot\text{m}^6/\text{mol}^2} a ( T ) = a c ​ ⋅ α = 1.0175 × 1.0859 = 1.1049 Pa ⋅ m 6 / mol 2

Evaluate pure component co-volume parameter b b b : b = 0.07780 R T c P c = 0.07780 ( 8.31447 ) ( 369.8 ) 4.248 × 10 6 = 5.633 × 10 − 5 m 3 / mol b = 0.07780 \frac{R T_c}{P_c} = 0.07780 \frac{(8.31447)(369.8)}{4.248 \times 10^6} = \mathbf{5.633 \times 10^{-5}\text{ m}^3/\text{mol}} b = 0.07780 P c ​ R T c ​ ​ = 0.07780 4.248 × 1 0 6 ( 8.31447 ) ( 369.8 ) ​ = 5.633 × 1 0 − 5 m 3 / mol

Step 3: Dimensionless Coefficients A A A and B B B A = a ( T ) P ( R T ) 2 = ( 1.1049 ) × ( 1.50 × 10 6 ) [ ( 8.31447 ) ( 320.0 ) ] 2 = 1.65735 × 10 6 ( 2660.63 ) 2 = 1.65735 × 10 6 7.07895 × 10 6 = 0.23412 A = \frac{a(T) P}{(R T)^2} = \frac{(1.1049) \times (1.50 \times 10^6)}{[(8.31447)(320.0)]^2} = \frac{1.65735 \times 10^6}{(2660.63)^2} = \frac{1.65735 \times 10^6}{7.07895 \times 10^6} = \mathbf{0.23412} A = ( RT ) 2 a ( T ) P ​ = [( 8.31447 ) ( 320.0 ) ] 2 ( 1.1049 ) × ( 1.50 × 1 0 6 ) ​ = ( 2660.63 ) 2 1.65735 × 1 0 6 ​ = 7.07895 × 1 0 6 1.65735 × 1 0 6 ​ = 0.23412 B = b P R T = ( 5.633 × 10 − 5 ) × ( 1.50 × 10 6 ) ( 8.31447 ) ( 320.0 ) = 84.495 2660.63 = 0.031758 B = \frac{b P}{R T} = \frac{(5.633 \times 10^{-5}) \times (1.50 \times 10^6)}{(8.31447)(320.0)} = \frac{84.495}{2660.63} = \mathbf{0.031758} B = RT b P ​ = ( 8.31447 ) ( 320.0 ) ( 5.633 × 1 0 − 5 ) × ( 1.50 × 1 0 6 ) ​ = 2660.63 84.495 ​ = 0.031758

Step 4: Formulation and Solution of the PR Cubic Polynomial

The Peng-Robinson cubic polynomial is: Z 3 − ( 1 − B ) Z 2 + ( A − 3 B 2 − 2 B ) Z − ( A B − B 2 − B 3 ) = 0 Z^3 - (1 - B)Z^2 + (A - 3B^2 - 2B)Z - (A B - B^2 - B^3) = 0 Z 3 − ( 1 − B ) Z 2 + ( A − 3 B 2 − 2 B ) Z − ( A B − B 2 − B 3 ) = 0

Calculate coefficients:

Coefficient of Z 2 Z^2 Z 2 : − ( 1 − B ) = − ( 1 − 0.031758 ) = − 0.96824 -(1 - B) = -(1 - 0.031758) = \mathbf{-0.96824} − ( 1 − B ) = − ( 1 − 0.031758 ) = − 0.96824

Coefficient of Z Z Z : A − 3 B 2 − 2 B = 0.23412 − 3 ( 0.031758 ) 2 − 2 ( 0.031758 ) = 0.23412 − 0.00303 − 0.06352 = + 0.16757 A - 3B^2 - 2B = 0.23412 - 3(0.031758)^2 - 2(0.031758) = 0.23412 - 0.00303 - 0.06352 = \mathbf{+0.16757} A − 3 B 2 − 2 B = 0.23412 − 3 ( 0.031758 ) 2 − 2 ( 0.031758 ) = 0.23412 − 0.00303 − 0.06352 = + 0.16757

Constant term: − ( A B − B 2 − B 3 ) = − [ ( 0.23412 ) ( 0.031758 ) − ( 0.031758 ) 2 − ( 0.031758 ) 3 ] = − [ 0.007435 − 0.001009 − 0.000032 ] = − 0.006394 -(A B - B^2 - B^3) = -[(0.23412)(0.031758) - (0.031758)^2 - (0.031758)^3] = -[0.007435 - 0.001009 - 0.000032] = \mathbf{-0.006394} − ( A B − B 2 − B 3 ) = − [( 0.23412 ) ( 0.031758 ) − ( 0.031758 ) 2 − ( 0.031758 ) 3 ] = − [ 0.007435 − 0.001009 − 0.000032 ] = − 0.006394

The polynomial is: f ( Z ) = Z 3 − 0.96824 Z 2 + 0.16757 Z − 0.006394 = 0 f(Z) = Z^3 - 0.96824 Z^2 + 0.16757 Z - 0.006394 = 0 f ( Z ) = Z 3 − 0.96824 Z 2 + 0.16757 Z − 0.006394 = 0

Because the propane is superheated vapor at T = 320 K T = 320\text{ K} T = 320 K and P = 1.5 MPa P = 1.5\text{ MPa} P = 1.5 MPa (propane saturation pressure at 320 K 320\text{ K} 320 K is P s a t ≈ 1.68 MPa > 1.50 MPa P^{sat} \approx 1.68\text{ MPa} > 1.50\text{ MPa} P s a t ≈ 1.68 MPa > 1.50 MPa ), we seek the largest root Z V Z_V Z V ​ .

Iterating via Newton-Raphson or substitution:

For Z = 0.76 Z = 0.76 Z = 0.76 : f ( 0.76 ) = ( 0.76 ) 3 − 0.96824 ( 0.76 ) 2 + 0.16757 ( 0.76 ) − 0.006394 f(0.76) = (0.76)^3 - 0.96824(0.76)^2 + 0.16757(0.76) - 0.006394 f ( 0.76 ) = ( 0.76 ) 3 − 0.96824 ( 0.76 ) 2 + 0.16757 ( 0.76 ) − 0.006394 f ( 0.76 ) = 0.43898 − 0.55925 + 0.12735 − 0.00639 = + 0.00069 f(0.76) = 0.43898 - 0.55925 + 0.12735 - 0.00639 = +0.00069 f ( 0.76 ) = 0.43898 − 0.55925 + 0.12735 − 0.00639 = + 0.00069

For Z = 0.758 Z = 0.758 Z = 0.758 : f ( 0.758 ) = 0.43552 − 0.55631 + 0.12702 − 0.00639 = − 0.00016 f(0.758) = 0.43552 - 0.55631 + 0.12702 - 0.00639 = -0.00016 f ( 0.758 ) = 0.43552 − 0.55631 + 0.12702 − 0.00639 = − 0.00016

Interpolating yields the vapor compressibility factor: Z V = 0.7583 ≈ 0.758 Z_V = \mathbf{0.7583} \approx \mathbf{0.758} Z V ​ = 0.7583 ≈ 0.758

Step 5: Molar Volume and Mass Density

Actual molar volume: v = Z V R T P = ( 0.7583 ) × ( 8.31447 J/(mol ⋅ K) ) × ( 300.0 K × 320.0 / 300.0 ) 1.50 × 10 6 Pa v = \frac{Z_V R T}{P} = \frac{(0.7583) \times (8.31447\text{ J/(mol}\cdot\text{K)}) \times (300.0\text{ K} \times 320.0/300.0)}{1.50 \times 10^6\text{ Pa}} v = P Z V ​ RT ​ = 1.50 × 1 0 6 Pa ( 0.7583 ) × ( 8.31447 J/(mol ⋅ K) ) × ( 300.0 K × 320.0/300.0 ) ​ v = ( 0.7583 ) × ( 2660.63 ) 1.50 × 10 6 = 1.345 × 10 − 3 m 3 / mol = 1.345 L/mol v = \frac{(0.7583) \times (2660.63)}{1.50 \times 10^6} = \mathbf{1.345 \times 10^{-3}\text{ m}^3/\text{mol}} = \mathbf{1.345\text{ L/mol}} v = 1.50 × 1 0 6 ( 0.7583 ) × ( 2660.63 ) ​ = 1.345 × 1 0 − 3 m 3 / mol = 1.345 L/mol

Mass density: ρ = M W v = 0.044097 kg/mol 0.001345 m 3 / mol = 32.79 kg/m 3 \rho = \frac{MW}{v} = \frac{0.044097\text{ kg/mol}}{0.001345\text{ m}^3/\text{mol}} = \mathbf{32.79\text{ kg/m}^3} ρ = v M W ​ = 0.001345 m 3 / mol 0.044097 kg/mol ​ = 32.79 kg/m 3

Step 6: Comparison with Ideal Gas Prediction

Ideal gas molar volume: v i g = R T P = 2660.63 1.50 × 10 6 = 1.774 × 10 − 3 m 3 / mol = 1.774 L/mol v^{ig} = \frac{R T}{P} = \frac{2660.63}{1.50 \times 10^6} = 1.774 \times 10^{-3}\text{ m}^3/\text{mol} = 1.774\text{ L/mol} v i g = P RT ​ = 1.50 × 1 0 6 2660.63 ​ = 1.774 × 1 0 − 3 m 3 / mol = 1.774 L/mol ρ i g = M W v i g = 0.044097 0.001774 = 24.86 kg/m 3 \rho^{ig} = \frac{MW}{v^{ig}} = \frac{0.044097}{0.001774} = 24.86\text{ kg/m}^3 ρ i g = v i g M W ​ = 0.001774 0.044097 ​ = 24.86 kg/m 3 Ideal Gas Density Error = 24.86 − 32.79 32.79 × 100 % = − 24.18 % \text{Ideal Gas Density Error} = \frac{24.86 - 32.79}{32.79} \times 100\% = \mathbf{-24.18\%} Ideal Gas Density Error = 32.79 24.86 − 32.79 ​ × 100% = − 24.18%

Assuming an ideal gas underpredicts the true mass of propane in the drum by over 24 % 24\% 24% , creating a severe risk of vessel overfilling or mass balance accounting failure.

  • 8. Critical PE Exam Traps & Pitfalls
  • Trap 1: Root Inversion (Selecting the Liquid Root for Vapor Flow)

When a cubic equation solver produces three roots, always double-check the physical phase. The largest root ( Z V Z_V Z V ​ ) represents vapor, while the smallest root ( Z L Z_L Z L ​ ) represents liquid. If a problem states "superheated vapor" or asks for the volume of gas exiting a reboiler, selecting Z L Z_L Z L ​ (which is typically around 0.03 − 0.08 0.03-0.08 0.03 − 0.08 ) will produce an answer off by a factor of 10 to 30.

Trap 2: Mixing Up Equation-Specific Parameters

Never mix parameters across equations! Using Ω a = 0.42748 \Omega_a = 0.42748 Ω a ​ = 0.42748 (from SRK) inside the Peng-Robinson polynomial, or using Peng-Robinson's κ \kappa κ formula with the SRK denominator, will produce completely corrupted results. Ensure you match the numerical constants exactly as given in the reference handbook.

Trap 3: Binary Interaction Parameter Arithmetic

In the cross-term a i j = a i a j ( 1 − k i j ) a_{ij} = \sqrt{a_i a_j}(1 - k_{ij}) a ij ​ = a i ​ a j ​ ​ ( 1 − k ij ​ ) , remember that k i j k_{ij} k ij ​ reduces the cross-attraction if k i j > 0 k_{ij} > 0 k ij ​ > 0 . A common exam trap tests your ability to expand a m i x = y 1 2 a 1 + 2 y 1 y 2 a 12 + y 2 2 a 2 a_{mix} = y_1^2 a_1 + 2 y_1 y_2 a_{12} + y_2^2 a_2 a mi x ​ = y 1 2 ​ a 1 ​ + 2 y 1 ​ y 2 ​ a 12 ​ + y 2 2 ​ a 2 ​ . Forgetting the factor of 2 2 2 on the cross term y 1 y 2 a 12 y_1 y_2 a_{12} y 1 ​ y 2 ​ a 12 ​ is a frequent algebra error.