Study guide

6.3 Residual Properties and Enthalpy/Entropy Departure Functions

PE Chemical Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the PE Chemical Exam How to Use This Guide and the NCEES Handbook

2 Chapter 1: Material Balances & Flowsheet Calculations

1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations

3 Chapter 2: Energy Balances & Thermochemistry

2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances

4 Chapter 3: Fluid Statics & Incompressible Pipe Flow

3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations

5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up

6 Chapter 5: Thermodynamic Laws & Fundamental Relations

5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations

7 Chapter 6: Real Gases & Equations of State

6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions

8 Chapter 7: Phase & Chemical Reaction Equilibria

7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation

9 Chapter 8: Heat Transfer Mechanisms & Conduction

8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange

10 Chapter 9: Heat Exchanger Design & Phase Change

9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances

11 Chapter 10: Mass Transfer Fundamentals & Diffusion

10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

12 Chapter 11: Distillation Operations

11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components

13 Chapter 12: Rate-Controlled & Equilibrium Separations

12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations

14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors

13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations

15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis

14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models

16 Chapter 15: Physical & Transport Properties of Fluids

15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles

17 Chapter 16: Materials of Construction & Corrosion

16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention

18 Chapter 17: Process Safety & Pressure Relief Systems

17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment

19 Chapter 18: Process Control & Engineering Economics

18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems

20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance

19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation

21 Chapter 20: Plant Operation, Reliability & Continuous Improvement

20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting

6.3 Residual Properties and Enthalpy/Entropy Departure Functions

Key Takeaways Explain This Topic AI

A residual property M^R(T, P) = M(T, P) - M^ig(T, P) quantifies the exact difference between an actual real fluid state property and its hypothetical ideal gas value at the identical temperature, pressure, and composition.

Thermodynamic departure paths decouple real fluid calculations into ideal gas temperature integrals (integral C_p^ig dT) and pressure-dependent residual departures at terminal states: Delta H = -H^R(T1, P1) + Delta H^ig(T1 -> T2) + H^R(T2, P2).

The fugacity coefficient phi = f/P represents the dimensionless exponent of residual Gibbs free energy (ln phi = G^R / (RT)), linking volumetric equations of state directly to phase equilibrium criteria (f_i^V = f_i^L).

Analytical departure functions derived from cubic equations of state (SRK, PR) allow exact computation of high-pressure enthalpy departures, entropy departures, and fugacities without empirical steam tables.

For isentropic compression and expansion, real gas entropy departures alter the discharge temperature and shaft work by up to 20-30% compared to ideal gas isentropic formulas, requiring an iterative departure balance: Delta S = 0.

Last updated: September 2026

6.3 Residual Properties and Enthalpy/Entropy Departure Functions

Thermodynamic property evaluations on the NCEES PE Chemical Exam extend far beyond ideal gas heat capacities and steam tables. In high-pressure chemical reactors, multi-stage gas compressors, Joule-Thomson refrigeration loops, and supercritical fluid processes, enthalpy changes ( Δ H \Delta H Δ H ) and entropy changes ( Δ S \Delta S Δ S ) deviate significantly from ideal gas behavior. Because enthalpy and entropy cannot be measured directly with physical gauges, chemical engineers evaluate real fluid behavior using residual properties (also termed departure functions ).

Residual properties link measurable P V T PVT P V T volumetric equations of state directly to unmeasurable caloric properties ( H , S , G , U H, S, G, U H , S , G , U ) through exact mathematical derivations grounded in the Maxwell relations .

1. The Theoretical Foundation of Residual Properties

A residual property ( M R M^R M R ) is defined as the difference between the actual molar thermodynamic property of a fluid ( M M M ) and the molar property the fluid would exhibit as an ideal gas ( M i g M^{ig} M i g ) at the identical temperature, pressure, and composition : M R ( T , P ) ≡ M ( T , P ) − M i g ( T , P ) M^R(T, P) \equiv M(T, P) - M^{ig}(T, P) M R ( T , P ) ≡ M ( T , P ) − M i g ( T , P )

Where M M M can represent molar volume ( v v v ), enthalpy ( h h h ), entropy ( s s s ), internal energy ( u u u ), Gibbs free energy ( g g g ), or Helmholtz free energy ( a a a ).

Why the Hypothetical Ideal Gas Reference?

All real gases approach ideal behavior as pressure approaches zero ( P → 0 P \to 0 P → 0 ). However, M i g ( T , P ) M^{ig}(T, P) M i g ( T , P ) is evaluated at the actual process pressure P P P , representing a hypothetical state where molecules possess their real thermal heat capacities ( C p i g ( T ) C_p^{ig}(T) C p i g ​ ( T ) ) but zero intermolecular forces and zero physical molecular volume.

The Volume Residual ( v R v^R v R )

The residual molar volume derives directly from the compressibility factor Z Z Z : v R = v − v i g = Z R T P − R T P = R T P ( Z − 1 ) v^R = v - v^{ig} = \frac{Z R T}{P} - \frac{R T}{P} = \frac{R T}{P}(Z - 1) v R = v − v i g = P ZRT ​ − P RT ​ = P RT ​ ( Z − 1 )

Notice that if a fluid behaves ideally, Z = 1 Z = 1 Z = 1 , and the residual volume is identically zero ( v R = 0 v^R = 0 v R = 0 ).

2. Fundamental Derivation of Departure Functions from Maxwell Relations

From the fundamental property relation for a single-phase fluid of constant composition: d G = V d P − S d T dG = V dP - S dT d G = V d P − S d T

For an ideal gas at the same T T T and P P P : d G i g = V i g d P − S i g d T dG^{ig} = V^{ig} dP - S^{ig} dT d G i g = V i g d P − S i g d T

Subtracting the ideal gas differential from the real fluid differential defines the residual Gibbs free energy differential ( d G R dG^R d G R ): d G R = ( V − V i g ) d P − ( S − S i g ) d T = V R d P − S R d T dG^R = (V - V^{ig}) dP - (S - S^{ig}) dT = V^R dP - S^R dT d G R = ( V − V i g ) d P − ( S − S i g ) d T = V R d P − S R d T

1. Residual Gibbs Free Energy & Fugacity Coefficient

At constant temperature ( d T = 0 dT = 0 d T = 0 ): ( ∂ G R ∂ P ) T = V R = R T P ( Z − 1 ) \left( \frac{\partial G^R}{\partial P} \right)_T = V^R = \frac{R T}{P}(Z - 1) ( ∂ P ∂ G R ​ ) T ​ = V R = P RT ​ ( Z − 1 )

Integrating from the zero-pressure ideal gas reference state ( P = 0 P = 0 P = 0 , where G R = 0 G^R = 0 G R = 0 ) to process pressure P P P : G R R T = ∫ 0 P Z − 1 P d P \frac{G^R}{R T} = \int_0^P \frac{Z - 1}{P} dP RT G R ​ = ∫ 0 P ​ P Z − 1 ​ d P

In chemical thermodynamics, the fugacity coefficient ( ϕ \phi ϕ ) of a pure substance is defined by: G − G i g = R T ln ⁡ ( f P ) = R T ln ⁡ ϕ G - G^{ig} = R T \ln\left( \frac{f}{P} \right) = R T \ln \phi G − G i g = RT ln ( P f ​ ) = RT ln ϕ

Therefore, the fugacity coefficient is the direct exponential of the residual Gibbs free energy: ln ⁡ ϕ = G R R T = ∫ 0 P Z − 1 P d P \ln \phi = \frac{G^R}{R T} = \int_0^P \frac{Z - 1}{P} dP ln ϕ = RT G R ​ = ∫ 0 P ​ P Z − 1 ​ d P

2. Residual Enthalpy Departure ( H R H^R H R )

Applying the Gibbs-Helmholtz relation ( H = − T 2 [ ∂ ( G / T ) / ∂ T ] P H = -T^2 [\partial(G/T)/\partial T]_P H = − T 2 [ ∂ ( G / T ) / ∂ T ] P ​ ): H R R T = − T [ ∂ ( G R / R T ) ∂ T ] P = − T ∫ 0 P ( ∂ Z ∂ T ) P d P P \frac{H^R}{R T} = -T \left[ \frac{\partial (G^R / R T)}{\partial T} \right]_P = -T \int_0^P \left( \frac{\partial Z}{\partial T} \right)_P \frac{dP}{P} RT H R ​ = − T [ ∂ T ∂ ( G R / RT ) ​ ] P ​ = − T ∫ 0 P ​ ( ∂ T ∂ Z ​ ) P ​ P d P ​ H R = − R T 2 ∫ 0 P ( ∂ Z ∂ T ) P d P P = ∫ 0 P [ v − T ( ∂ v ∂ T ) P ] d P H^R = -R T^2 \int_0^P \left( \frac{\partial Z}{\partial T} \right)_P \frac{dP}{P} = \int_0^P \left[ v - T \left( \frac{\partial v}{\partial T} \right)_P \right] dP H R = − R T 2 ∫ 0 P ​ ( ∂ T ∂ Z ​ ) P ​ P d P ​ = ∫ 0 P ​ [ v − T ( ∂ T ∂ v ​ ) P ​ ] d P

3. Residual Entropy Departure ( S R S^R S R )

From the definition G R = H R − T S R G^R = H^R - T S^R G R = H R − T S R , solving for residual entropy yields: S R R = H R R T − G R R T = − T ∫ 0 P ( ∂ Z ∂ T ) P d P P − ∫ 0 P ( Z − 1 ) d P P \frac{S^R}{R} = \frac{H^R}{R T} - \frac{G^R}{R T} = -T \int_0^P \left( \frac{\partial Z}{\partial T} \right)_P \frac{dP}{P} - \int_0^P (Z - 1) \frac{dP}{P} R S R ​ = RT H R ​ − RT G R ​ = − T ∫ 0 P ​ ( ∂ T ∂ Z ​ ) P ​ P d P ​ − ∫ 0 P ​ ( Z − 1 ) P d P ​ S R = ∫ 0 P [ R P − ( ∂ v ∂ T ) P ] d P S^R = \int_0^P \left[ \frac{R}{P} - \left( \frac{\partial v}{\partial T} \right)_P \right] dP S R = ∫ 0 P ​ [ P R ​ − ( ∂ T ∂ v ​ ) P ​ ] d P

3. Volume-Explicit vs. Pressure-Explicit Integral Forms

While the derivations above integrate with respect to pressure, cubic equations of state (vdW, SRK, PR) express pressure as an explicit function of molar volume: P = f ( T , v ) P = f(T, v) P = f ( T , v ) . Converting the departure integrals from ( T , P ) (T, P) ( T , P ) coordinates to ( T , v ) (T, v) ( T , v ) coordinates via integration by parts yields the general volume-explicit departure formulas: H R R T = Z − 1 + 1 R T ∫ ∞ v [ T ( ∂ P ∂ T ) v − P ] d v \frac{H^R}{R T} = Z - 1 + \frac{1}{R T} \int_\infty^v \left[ T \left( \frac{\partial P}{\partial T} \right)_v - P \right] dv RT H R ​ = Z − 1 + RT 1 ​ ∫ ∞ v ​ [ T ( ∂ T ∂ P ​ ) v ​ − P ] d v S R R = ln ⁡ Z + 1 R ∫ ∞ v [ ( ∂ P ∂ T ) v − R v ] d v \frac{S^R}{R} = \ln Z + \frac{1}{R} \int_\infty^v \left[ \left( \frac{\partial P}{\partial T} \right)_v - \frac{R}{v} \right] dv R S R ​ = ln Z + R 1 ​ ∫ ∞ v ​ [ ( ∂ T ∂ P ​ ) v ​ − v R ​ ] d v ln ⁡ ϕ = Z − 1 − ln ⁡ Z − 1 R T ∫ ∞ v ( P − R T v ) d v \ln \phi = Z - 1 - \ln Z - \frac{1}{R T} \int_\infty^v \left( P - \frac{R T}{v} \right) dv ln ϕ = Z − 1 − ln Z − RT 1 ​ ∫ ∞ v ​ ( P − v RT ​ ) d v

These universal integral equations allow analytical evaluation of departure functions for any analytical equation of state.

  • 4. Analytical Residual Expressions for Virial and Cubic Equations of State
  • 1. Truncated Virial Equation ( Z = 1 + B P / R T Z = 1 + B P / R T Z = 1 + BP / RT )

For low to moderate pressures where the two-term virial equation is valid, analytical differentiation yields: ln ⁡ ϕ = B P R T = Z − 1 \ln \phi = \frac{B P}{R T} = Z - 1 ln ϕ = RT BP ​ = Z − 1 H R R T = P R ( B T − d B d T ) \frac{H^R}{R T} = \frac{P}{R} \left( \frac{B}{T} - \frac{dB}{dT} \right) RT H R ​ = R P ​ ( T B ​ − d T d B ​ ) S R R = − P R ( d B d T ) \frac{S^R}{R} = -\frac{P}{R} \left( \frac{dB}{dT} \right) R S R ​ = − R P ​ ( d T d B ​ )

2. Soave-Redlich-Kwong (SRK)

Integrating the SRK equation of state yields: ln ⁡ ϕ = Z − 1 − ln ⁡ ( Z − B ) − A B ln ⁡ ( 1 + B Z ) \ln \phi = Z - 1 - \ln(Z - B) - \frac{A}{B} \ln\left( 1 + \frac{B}{Z} \right) ln ϕ = Z − 1 − ln ( Z − B ) − B A ​ ln ( 1 + Z B ​ ) H R R T = Z − 1 − A B [ 1 + m T r α ] ln ⁡ ( 1 + B Z ) \frac{H^R}{R T} = Z - 1 - \frac{A}{B} \left[ 1 + \frac{m \sqrt{T_r}}{\sqrt{\alpha}} \right] \ln\left( 1 + \frac{B}{Z} \right) RT H R ​ = Z − 1 − B A ​ [ 1 + α ​ m T r ​ ​ ​ ] ln ( 1 + Z B ​ ) S R R = ln ⁡ ( Z − B ) − A B [ m T r α ] ln ⁡ ( 1 + B Z ) \frac{S^R}{R} = \ln(Z - B) - \frac{A}{B} \left[ \frac{m \sqrt{T_r}}{\sqrt{\alpha}} \right] \ln\left( 1 + \frac{B}{Z} \right) R S R ​ = ln ( Z − B ) − B A ​ [ α ​ m T r ​ ​ ​ ] ln ( 1 + Z B ​ )

3. Peng-Robinson (PR)

Integrating the Peng-Robinson equation of state yields the industry standard departure formulations: ln ⁡ ϕ = Z − 1 − ln ⁡ ( Z − B ) − A 2 2 B ln ⁡ [ Z + ( 1 + 2 ) B Z + ( 1 − 2 ) B ] \ln \phi = Z - 1 - \ln(Z - B) - \frac{A}{2\sqrt{2} B} \ln\left[ \frac{Z + (1 + \sqrt{2})B}{Z + (1 - \sqrt{2})B} \right] ln ϕ = Z − 1 − ln ( Z − B ) − 2 2 ​ B A ​ ln [ Z + ( 1 − 2 ​ ) B Z + ( 1 + 2 ​ ) B ​ ] H R R T = Z − 1 − A 2 2 B [ 1 + κ T r α ] ln ⁡ [ Z + ( 1 + 2 ) B Z + ( 1 − 2 ) B ] \frac{H^R}{R T} = Z - 1 - \frac{A}{2\sqrt{2} B} \left[ 1 + \frac{\kappa \sqrt{T_r}}{\sqrt{\alpha}} \right] \ln\left[ \frac{Z + (1 + \sqrt{2})B}{Z + (1 - \sqrt{2})B} \right] RT H R ​ = Z − 1 − 2 2 ​ B A ​ [ 1 + α ​ κ T r ​ ​ ​ ] ln [ Z + ( 1 − 2 ​ ) B Z + ( 1 + 2 ​ ) B ​ ] S R R = ln ⁡ ( Z − B ) − A 2 2 B [ κ T r α ] ln ⁡ [ Z + ( 1 + 2 ) B Z + ( 1 − 2 ) B ] \frac{S^R}{R} = \ln(Z - B) - \frac{A}{2\sqrt{2} B} \left[ \frac{\kappa \sqrt{T_r}}{\sqrt{\alpha}} \right] \ln\left[ \frac{Z + (1 + \sqrt{2})B}{Z + (1 - \sqrt{2})B} \right] R S R ​ = ln ( Z − B ) − 2 2 ​ B A ​ [ α ​ κ T r ​ ​ ​ ] ln [ Z + ( 1 − 2 ​ ) B Z + ( 1 + 2 ​ ) B ​ ]

Where A = a P / ( R T ) 2 A = a P / (R T)^2 A = a P / ( RT ) 2 and B = b P / R T B = b P / R T B = b P / RT .

5. Generalized Three-Parameter Lee-Kesler Departure Tables

When cubic equations are not solved analytically on the PE exam, candidates utilize the generalized Lee-Kesler departure tables in the NCEES Reference Handbook. These express dimensionless residual enthalpy and entropy as two-term acentric factor expansions: H R R T c = ( H R R T c ) ( 0 ) + ω ( H R R T c ) ( 1 ) \frac{H^R}{R T_c} = \left( \frac{H^R}{R T_c} \right)^{(0)} + \omega \left( \frac{H^R}{R T_c} \right)^{(1)} R T c ​ H R ​ = ( R T c ​ H R ​ ) ( 0 ) + ω ( R T c ​ H R ​ ) ( 1 ) S R R = ( S R R ) ( 0 ) + ω ( S R R ) ( 1 ) \frac{S^R}{R} = \left( \frac{S^R}{R} \right)^{(0)} + \omega \left( \frac{S^R}{R} \right)^{(1)} R S R ​ = ( R S R ​ ) ( 0 ) + ω ( R S R ​ ) ( 1 ) log ⁡ 10 ( ϕ ) = ( log ⁡ 10 ϕ ) ( 0 ) + ω ( log ⁡ 10 ϕ ) ( 1 ) \log_{10}(\phi) = (\log_{10}\phi)^{(0)} + \omega (\log_{10}\phi)^{(1)} lo g 10 ​ ( ϕ ) = ( lo g 10 ​ ϕ ) ( 0 ) + ω ( lo g 10 ​ ϕ ) ( 1 )

Both the simple fluid terms (superscript 0 0 0 ) and correction terms (superscript 1 1 1 ) are tabulated against reduced temperature ( T r T_r T r ​ ) and reduced pressure ( P r P_r P r ​ ).

6. The Three-Step Thermodynamic Process Path

Because enthalpy ( H H H ) and entropy ( S S S ) are state functions , their changes between State 1 ( T 1 , P 1 T_1, P_1 T 1 ​ , P 1 ​ ) and State 2 ( T 2 , P 2 T_2, P_2 T 2 ​ , P 2 ​ ) depend only on the initial and final states, not the physical path.

Direct integration of real fluid properties between ( T 1 , P 1 ) (T_1, P_1) ( T 1 ​ , P 1 ​ ) and ( T 2 , P 2 ) (T_2, P_2) ( T 2 ​ , P 2 ​ ) is difficult because heat capacity varies with both temperature and pressure ( C p ( T , P ) C_p(T, P) C p ​ ( T , P ) ). Chemical engineers replace the real process path with a three-step hypothetical path : Real State 1 (T_1, P_1) --------------------------> Real State 2 (T_2, P_2)

  • | ^
  • | Step 1: Depressurization | Step 3: Pressurization
  • | ΔH_1 = -H^R(T_1, P_1) | ΔH_3 = +H^R(T_2, P_2)
  • v |
  • Ideal Gas (T_1, P -> 0) ------> Step 2 ---------> Ideal Gas (T_2, P -> 0)
  • Ideal Sensible Heating
  • ΔH_2 = ∫ C_p^ig(T) dT
  • Governing Equations for Real Changes

1. Enthalpy Change ( Δ H \Delta H Δ H ): Δ H = Δ H 1 + Δ H 2 + Δ H 3 \Delta H = \Delta H_1 + \Delta H_2 + \Delta H_3 Δ H = Δ H 1 ​ + Δ H 2 ​ + Δ H 3 ​ Δ H = − H R ( T 1 , P 1 ) + ∫ T 1 T 2 C p i g ( T ) d T + H R ( T 2 , P 2 ) \Delta H = -H^R(T_1, P_1) + \int_{T_1}^{T_2} C_p^{ig}(T) dT + H^R(T_2, P_2) Δ H = − H R ( T 1 ​ , P 1 ​ ) + ∫ T 1 ​ T 2 ​ ​ C p i g ​ ( T ) d T + H R ( T 2 ​ , P 2 ​ )

2. Entropy Change ( Δ S \Delta S Δ S ): Δ S = − S R ( T 1 , P 1 ) + [ ∫ T 1 T 2 C p i g ( T ) T d T − R ln ⁡ ( P 2 P 1 ) ] + S R ( T 2 , P 2 ) \Delta S = -S^R(T_1, P_1) + \left[ \int_{T_1}^{T_2} \frac{C_p^{ig}(T)}{T} dT - R \ln\left( \frac{P_2}{P_1} \right) \right] + S^R(T_2, P_2) Δ S = − S R ( T 1 ​ , P 1 ​ ) + [ ∫ T 1 ​ T 2 ​ ​ T C p i g ​ ( T ) ​ d T − R ln ( P 1 ​ P 2 ​ ​ ) ] + S R ( T 2 ​ , P 2 ​ )

Important

Sign Convention Rule:

In Step 1, the fluid transitions from the real state to the ideal gas state , which is the reverse of departure; hence, we subtract the initial residual property: − H R ( T 1 , P 1 ) -H^R(T_1, P_1) − H R ( T 1 ​ , P 1 ​ ) and − S R ( T 1 , P 1 ) -S^R(T_1, P_1) − S R ( T 1 ​ , P 1 ​ ) .

In Step 3, the fluid transitions from the ideal gas state to the final real state ; hence, we add the final residual property: + H R ( T 2 , P 2 ) +H^R(T_2, P_2) + H R ( T 2 ​ , P 2 ​ ) and + S R ( T 2 , P 2 ) +S^R(T_2, P_2) + S R ( T 2 ​ , P 2 ​ ) .

7. Summary Table: Departure Function Formulations Across Models

Property Truncated Virial ( Z = 1 + B P / R T Z = 1 + BP/RT Z = 1 + BP / RT ) Soave-Redlich-Kwong (SRK) Peng-Robinson (PR) Lee-Kesler Tabulations

Fugacity Coeff. ( ln ⁡ ϕ \ln \phi ln ϕ ) B P R T \frac{B P}{R T} RT BP ​ Z − 1 − ln ⁡ ( Z − B ) − A B ln ⁡ ( 1 + B Z ) Z - 1 - \ln(Z-B) - \frac{A}{B}\ln(1+\frac{B}{Z}) Z − 1 − ln ( Z − B ) − B A ​ ln ( 1 + Z B ​ ) Z − 1 − ln ⁡ ( Z − B ) − A 2 2 B ln ⁡ [ Z + 2.414 B Z − 0.414 B ] Z - 1 - \ln(Z-B) - \frac{A}{2\sqrt{2}B}\ln[\frac{Z+2.414B}{Z-0.414B}] Z − 1 − ln ( Z − B ) − 2 2 ​ B A ​ ln [ Z − 0.414 B Z + 2.414 B ​ ] ( log ⁡ 10 ϕ ) ( 0 ) + ω ( log ⁡ 10 ϕ ) ( 1 ) (\log_{10}\phi)^{(0)} + \omega (\log_{10}\phi)^{(1)} ( lo g 10 ​ ϕ ) ( 0 ) + ω ( lo g 10 ​ ϕ ) ( 1 )

Enthalpy Departure ( H R H^R H R ) P 2 R T ( … ) ≈ P ( B − T d B d T ) \frac{P^2}{R T}(\dots) \approx P(B - T \frac{dB}{dT}) RT P 2 ​ ( … ) ≈ P ( B − T d T d B ​ ) Function of Z , A , B , m , T r Z, A, B, m, T_r Z , A , B , m , T r ​ Function of Z , A , B , κ , T r Z, A, B, \kappa, T_r Z , A , B , κ , T r ​ R T c [ ( H R R T c ) ( 0 ) + ω ( H R R T c ) ( 1 ) ] R T_c [(\frac{H^R}{RT_c})^{(0)} + \omega (\frac{H^R}{RT_c})^{(1)}] R T c ​ [( R T c ​ H R ​ ) ( 0 ) + ω ( R T c ​ H R ​ ) ( 1 ) ]

Entropy Departure ( S R S^R S R ) − P ( d B d T ) -P \left( \frac{dB}{dT} \right) − P ( d T d B ​ ) Function of Z , A , B , m , T r Z, A, B, m, T_r Z , A , B , m , T r ​ Function of Z , A , B , κ , T r Z, A, B, \kappa, T_r Z , A , B , κ , T r ​ R [ ( S R R ) ( 0 ) + ω ( S R R ) ( 1 ) ] R [(\frac{S^R}{R})^{(0)} + \omega (\frac{S^R}{R})^{(1)}] R [( R S R ​ ) ( 0 ) + ω ( R S R ​ ) ( 1 ) ]

Primary Exam Use Low pressure ( P r < 0.5 P_r < 0.5 P r ​ < 0.5 ) Refining VLE, light hydrocarbons Gas processing, high-pressure pipelines General real gas problems without EOS software

  • 8. Comprehensive Worked Numerical Example: High-Pressure Carbon Dioxide Gas Heater Sizing
  • Problem Statement

A supercritical carbon dioxide ( CO 2 \text{CO}_2 CO 2 ​ ) extraction unit operates an in-line electric process preheater. Pure CO 2 \text{CO}_2 CO 2 ​ gas enters the heater at State 1 ( T 1 = 310.0 K T_1 = 310.0\text{ K} T 1 ​ = 310.0 K , P 1 = 8.00 MPa P_1 = 8.00\text{ MPa} P 1 ​ = 8.00 MPa ) at a molar flow rate of n ˙ = 500.0 mol/s \dot{n} = 500.0\text{ mol/s} n ˙ = 500.0 mol/s .

The gas is heated isobarically ( P 2 = P 1 = 8.00 MPa = 80.0 bar P_2 = P_1 = 8.00\text{ MPa} = 80.0\text{ bar} P 2 ​ = P 1 ​ = 8.00 MPa = 80.0 bar ) to State 2 ( T 2 = 420.0 K T_2 = 420.0\text{ K} T 2 ​ = 420.0 K ) before entering the extraction column.

Thermodynamic Data for CO 2 \text{CO}_2 CO 2 ​ ( M W = 44.01 g/mol MW = 44.01\text{ g/mol} M W = 44.01 g/mol , T c = 304.2 K T_c = 304.2\text{ K} T c ​ = 304.2 K , P c = 7.38 MPa P_c = 7.38\text{ MPa} P c ​ = 7.38 MPa ):

At State 1 ( 310.0 K , 8.00 MPa 310.0\text{ K}, 8.00\text{ MPa} 310.0 K , 8.00 MPa ): Tabulated molar enthalpy departure is H 1 R = − 6 , 850.0 J/mol H^R_1 = -6,850.0\text{ J/mol} H 1 R ​ = − 6 , 850.0 J/mol .

At State 2 ( 420.0 K , 8.00 MPa 420.0\text{ K}, 8.00\text{ MPa} 420.0 K , 8.00 MPa ): Tabulated molar enthalpy departure is H 2 R = − 1 , 420.0 J/mol H^R_2 = -1,420.0\text{ J/mol} H 2 R ​ = − 1 , 420.0 J/mol .

Ideal gas heat capacity for CO 2 \text{CO}_2 CO 2 ​ across this range is given by the mean value: C ˉ p i g = 41.50 J/(mol ⋅ K) \bar{C}_p^{ig} = 41.50\text{ J/(mol}\cdot\text{K)} C ˉ p i g ​ = 41.50 J/(mol ⋅ K) .

Calculate:

The reduced temperatures ( T r 1 , T r 2 T_{r1}, T_{r2} T r 1 ​ , T r 2 ​ ) and reduced pressure ( P r P_r P r ​ ) to confirm real fluid regime.

The ideal gas enthalpy change ( Δ H i g \Delta H^{ig} Δ H i g ) from T 1 T_1 T 1 ​ to T 2 T_2 T 2 ​ .

The actual molar enthalpy change ( Δ H \Delta H Δ H ) of the CO 2 \text{CO}_2 CO 2 ​ stream.

The required electrical heating duty ( Q ˙ \dot{Q} Q ˙ ​ ) in kilowatts ( kW \text{kW} kW ).

The heating duty that would have been calculated if the engineer had mistakenly assumed ideal gas behavior, and the engineering consequences of that assumption.

Step 1: Reduced Coordinates T r 1 = T 1 T c = 310.0 K 304.2 K = 1.019 T_{r1} = \frac{T_1}{T_c} = \frac{310.0\text{ K}}{304.2\text{ K}} = \mathbf{1.019} T r 1 ​ = T c ​ T 1 ​ ​ = 304.2 K 310.0 K ​ = 1.019 T r 2 = T 2 T c = 420.0 K 304.2 K = 1.381 T_{r2} = \frac{T_2}{T_c} = \frac{420.0\text{ K}}{304.2\text{ K}} = \mathbf{1.381} T r 2 ​ = T c ​ T 2 ​ ​ = 304.2 K 420.0 K ​ = 1.381 P r = P P c = 8.00 MPa 7.38 MPa = 1.084 P_r = \frac{P}{P_c} = \frac{8.00\text{ MPa}}{7.38\text{ MPa}} = \mathbf{1.084} P r ​ = P c ​ P ​ = 7.38 MPa 8.00 MPa ​ = 1.084

Because T r 1 ≈ 1.02 T_{r1} \approx 1.02 T r 1 ​ ≈ 1.02 and P r = 1.08 P_r = 1.08 P r ​ = 1.08 , State 1 is right in the dense supercritical transition region just above the critical point, where intermolecular attractive forces are extremely strong and real gas deviations are severe.

Step 2: Ideal Gas Enthalpy Change (Step 2) Δ H i g = ∫ T 1 T 2 C p i g ( T ) d T = C ˉ p i g ( T 2 − T 1 ) \Delta H^{ig} = \int_{T_1}^{T_2} C_p^{ig}(T) dT = \bar{C}_p^{ig} (T_2 - T_1) Δ H i g = ∫ T 1 ​ T 2 ​ ​ C p i g ​ ( T ) d T = C ˉ p i g ​ ( T 2 ​ − T 1 ​ ) Δ H i g = ( 41.50 J/(mol ⋅ K) ) × ( 420.0 − 310.0 ) K = 41.50 × 110.0 = 4 , 565.0 J/mol \Delta H^{ig} = (41.50\text{ J/(mol}\cdot\text{K)}) \times (420.0 - 310.0)\text{ K} = 41.50 \times 110.0 = \mathbf{4,565.0\text{ J/mol}} Δ H i g = ( 41.50 J/(mol ⋅ K) ) × ( 420.0 − 310.0 ) K = 41.50 × 110.0 = 4 , 565.0 J/mol

Step 3: Actual Molar Enthalpy Change

Apply the three-step departure formulation: Δ H = − H 1 R + Δ H i g + H 2 R \Delta H = -H^R_1 + \Delta H^{ig} + H^R_2 Δ H = − H 1 R ​ + Δ H i g + H 2 R ​ Δ H = − ( − 6 , 850.0 J/mol ) + 4 , 565.0 J/mol + ( − 1 , 420.0 J/mol ) \Delta H = -(-6,850.0\text{ J/mol}) + 4,565.0\text{ J/mol} + (-1,420.0\text{ J/mol}) Δ H = − ( − 6 , 850.0 J/mol ) + 4 , 565.0 J/mol + ( − 1 , 420.0 J/mol ) Δ H = + 6 , 850.0 + 4 , 565.0 − 1 , 420.0 = 9 , 995.0 J/mol \Delta H = +6,850.0 + 4,565.0 - 1,420.0 = \mathbf{9,995.0\text{ J/mol}} Δ H = + 6 , 850.0 + 4 , 565.0 − 1 , 420.0 = 9 , 995.0 J/mol

Thermodynamic Insight : In heating the fluid from 310 K 310\text{ K} 310 K to 420 K 420\text{ K} 420 K , we must supply 4 , 565 J/mol 4,565\text{ J/mol} 4 , 565 J/mol to increase molecular kinetic energy (sensible heat), PLUS we must supply ( 6 , 850 − 1 , 420 ) = 5 , 430 J/mol (6,850 - 1,420) = 5,430\text{ J/mol} ( 6 , 850 − 1 , 420 ) = 5 , 430 J/mol of energy to pull the molecules apart against their strong mutual attractive forces. The real fluid requires more than double the energy of an ideal gas!

Step 4: Required Electric Heater Duty

For an open steady-state heating unit with no shaft work ( W ˙ s = 0 \dot{W}_s = 0 W ˙ s ​ = 0 ): Q ˙ = n ˙ Δ H \dot{Q} = \dot{n} \Delta H Q ˙ ​ = n ˙ Δ H Q ˙ = ( 500.0 mol/s ) × ( 9 , 995.0 J/mol ) = 4 , 997 , 500 W = 4 , 997.5 kW ≈ 4 , 998 kW (5.00 MW) \dot{Q} = (500.0\text{ mol/s}) \times (9,995.0\text{ J/mol}) = 4,997,500\text{ W} = \mathbf{4,997.5\text{ kW}} \approx \mathbf{4,998\text{ kW}} \text{ (5.00 MW)} Q ˙ ​ = ( 500.0 mol/s ) × ( 9 , 995.0 J/mol ) = 4 , 997 , 500 W = 4 , 997.5 kW ≈ 4 , 998 kW (5.00 MW)

Step 5: Comparison with Ideal Gas Assumption

If ideal gas behavior had been assumed: Q ˙ i d e a l = n ˙ Δ H i g = ( 500.0 mol/s ) × ( 4 , 565.0 J/mol ) = 2 , 282 , 500 W = 2 , 282.5 kW \dot{Q}_{ideal} = \dot{n} \Delta H^{ig} = (500.0\text{ mol/s}) \times (4,565.0\text{ J/mol}) = 2,282,500\text{ W} = \mathbf{2,282.5\text{ kW}} Q ˙ ​ i d e a l ​ = n ˙ Δ H i g = ( 500.0 mol/s ) × ( 4 , 565.0 J/mol ) = 2 , 282 , 500 W = 2 , 282.5 kW Underprediction = Q ˙ i d e a l − Q ˙ r e a l Q ˙ r e a l × 100 % = 2 , 282.5 − 4 , 997.5 4 , 997.5 × 100 % = − 54.33 % \text{Underprediction} = \frac{\dot{Q}_{ideal} - \dot{Q}_{real}}{\dot{Q}_{real}} \times 100\% = \frac{2,282.5 - 4,997.5}{4,997.5} \times 100\% = \mathbf{-54.33\%} Underprediction = Q ˙ ​ re a l ​ Q ˙ ​ i d e a l ​ − Q ˙ ​ re a l ​ ​ × 100% = 4 , 997.5 2 , 282.5 − 4 , 997.5 ​ × 100% = − 54.33%

An engineer who designs the heater using the ideal gas law would undersize the heating element by 54.3 % 54.3\% 54.3% . In the actual plant, the heater would fail to reach the target extraction temperature of 420 K 420\text{ K} 420 K , stalling extraction and potentially overloading the electrical supply.

  • 9. Critical PE Exam Traps & Pitfalls
  • Trap 1: The Initial Departure Sign Error

The most common error in residual enthalpy calculations is writing Δ H = H 1 R + Δ H i g + H 2 R \Delta H = H^R_1 + \Delta H^{ig} + H^R_2 Δ H = H 1 R ​ + Δ H i g + H 2 R ​ . The initial state departure must be subtracted ( − H 1 R -H^R_1 − H 1 R ​ ) because the first step depressurizes the real gas to the ideal gas state. Since H R H^R H R is typically negative for attractive gases, subtracting a negative number yields a positive contribution: − ( − 6 , 850 ) = + 6 , 850 J/mol -(-6,850) = +6,850\text{ J/mol} − ( − 6 , 850 ) = + 6 , 850 J/mol .

Trap 2: Mixing Pressure Units in the Residual Entropy Formulation

In the entropy departure equation, the ideal gas pressure change is − R ln ⁡ ( P 2 / P 1 ) -R \ln(P_2 / P_1) − R ln ( P 2 ​ / P 1 ​ ) . This pressure ratio is strictly part of the ideal gas step . Do not insert P 2 / P 1 P_2 / P_1 P 2 ​ / P 1 ​ into the residual entropy functions S R S^R S R . Furthermore, P 1 P_1 P 1 ​ and P 2 P_2 P 2 ​ must be in the same absolute units so the ratio is dimensionless.

Trap 3: Misinterpreting Reference Table Headers

Handbooks and exam reference manuals often tabulate departure values with a leading negative sign, such as − ( H − H i g ) / ( R T c ) -(H - H^{ig}) / (R T_c) − ( H − H i g ) / ( R T c ​ ) or − ( H R ) / ( R T c ) -(H^R) / (R T_c) − ( H R ) / ( R T c ​ ) to report positive tabulated numbers. If the table heading already has a minus sign, the tabulated value is positive, but the actual residual property H R H^R H R is negative! Always verify whether the table header includes the negative sign before plugging numbers into your equation.

Trap 4: Confusing Fugacity with Fugacity Coefficient

Remember that the fugacity coefficient ϕ = f / P \phi = f / P ϕ = f / P is dimensionless, whereas fugacity f = ϕ P f = \phi P f = ϕP has units of pressure ( bar \text{bar} bar , kPa \text{kPa} kPa , or psia \text{psia} psia ). At low pressures, lim ⁡ P → 0 ϕ = 1.00 \lim_{P \to 0} \phi = 1.00 lim P → 0 ​ ϕ = 1.00 and lim ⁡ P → 0 f = P \lim_{P \to 0} f = P lim P → 0 ​ f = P .