Study guide
8.2 Convective Heat Transfer and Dimensionless Correlations
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
8.2 Convective Heat Transfer and Dimensionless Correlations
Key Takeaways Explain This Topic AI
Convective heat transfer is governed by Newton's law of cooling q = h A (T_s - T_inf), where the film coefficient h is a complex function of fluid flow regime, boundary layer development, geometry, and thermophysical properties.
The Nusselt number Nu = h L / k_f represents the ratio of convective heat transfer to pure molecular conduction across a fluid layer of characteristic length L; the Prandtl number Pr = Cp mu / k_f = nu / alpha represents the ratio of momentum diffusivity to thermal diffusivity.
For fully developed turbulent flow inside smooth circular tubes (Re > 10,000, 0.7 <= Pr <= 160, L/D > 10), the Dittus-Boelter correlation is Nu = 0.023 Re^0.8 Pr^n, where n = 0.4 when the fluid is heated (T_w > T_b) and n = 0.3 when the fluid is cooled (T_w < T_b).
In fully developed laminar pipe flow (Re < 2,300), the Nusselt number is strictly constant and independent of Reynolds and Prandtl numbers: Nu = 4.364 for uniform surface heat flux (q'' = const) and Nu = 3.657 for uniform surface temperature (T_s = const).
Natural convection is driven by buoyant body forces resulting from density gradients, governed by the Grashof number Gr = g beta Delta T L^3 / nu^2 and Rayleigh number Ra = Gr Pr; for ideal gases, the thermal expansion coefficient is strictly beta = 1 / T_film (with T_film evaluated in absolute temperature K or °R).
Last updated: September 2026
8.2 Convective Heat Transfer and Dimensionless Correlations
Convective heat transfer occurs between a solid surface and an adjacent moving fluid (liquid or gas) and encompasses the combined mechanisms of molecular diffusion (conduction) and macroscopic bulk advection. In chemical processing plants, convection governs heat exchange in shell-and-tube exchangers, reboilers, jackets and internal coils of stirred-tank reactors, and ambient cooling of process piping.
On the NCEES PE Chemical Exam , questions test your ability to select the appropriate dimensionless correlation , evaluate physical properties at the correct reference temperature ( bulk temperature vs. film temperature ), account for heating versus cooling exponents, and distinguish between laminar and turbulent flow regimes.
1. Convection Mechanisms & Boundary Layer Theory
Convective heat transfer is described globally by Newton's Law of Cooling : q = h A ( T s − T ∞ ) q = h A (T_s - T_\infty) q = h A ( T s − T ∞ )
Where:
q q q = heat transfer rate ( W \text{W} W or Btu/hr \text{Btu/hr} Btu/hr ).
h h h = convective heat transfer coefficient ( W/(m 2 ⋅ K) \text{W/(m}^2\cdot\text{K)} W/(m 2 ⋅ K) or Btu/(hr ⋅ ft 2 ⋅ ∘ F) \text{Btu/(hr}\cdot\text{ft}^2\cdot^\circ\text{F)} Btu/(hr ⋅ ft 2 ⋅ ∘ F) ).
A A A = surface area of heat transfer ( m 2 \text{m}^2 m 2 or ft 2 \text{ft}^2 ft 2 ).
T s T_s T s = solid surface temperature.
T ∞ T_\infty T ∞ = bulk fluid temperature far from the surface (or mixing-cup bulk temperature T b T_b T b in ducts).
Unlike thermal conductivity k k k , the convective heat transfer coefficient h h h is not an intrinsic physical property of the fluid . Rather, h h h depends on the flow field, surface geometry, fluid velocity, turbulence intensity, and fluid properties ( ρ , μ , C p , k \rho, \mu, C_p, k ρ , μ , C p , k ).
Hydrodynamic vs. Thermal Boundary Layers
When a fluid flows over a surface, viscous shear forces create a hydrodynamic (velocity) boundary layer of thickness δ ( x ) \delta(x) δ ( x ) , within which velocity transitions from zero at the wall (no-slip condition) to 99 % 99\% 99% of the freestream velocity u ∞ u_\infty u ∞ . Simultaneously, temperature differences generate a thermal boundary layer of thickness δ t ( x ) \delta_t(x) δ t ( x ) , within which temperature transitions from T s T_s T s to T ∞ T_\infty T ∞ .
The relative growth and thickness of these two boundary layers is determined by the Prandtl number ( P r Pr P r ): δ δ t ≈ P r 1 / 3 \frac{\delta}{\delta_t} \approx Pr^{1/3} δ t δ ≈ P r 1/3
Liquid metals ( P r ≪ 1 Pr \ll 1 P r ≪ 1 , e.g., P r ≈ 0.005 − 0.03 Pr \approx 0.005 - 0.03 P r ≈ 0.005 − 0.03 ) : Thermal diffusivity dwarfs momentum diffusivity ( α ≫ ν \alpha \gg \nu α ≫ ν ). The thermal boundary layer is much thicker than the velocity boundary layer ( δ t ≫ δ \delta_t \gg \delta δ t ≫ δ ). Molecular conduction dominates throughout the fluid.
Gases ( P r ≈ 0.7 − 1.0 Pr \approx 0.7 - 1.0 P r ≈ 0.7 − 1.0 ) : Thermal and momentum boundary layers grow at nearly identical rates ( δ t ≈ δ \delta_t \approx \delta δ t ≈ δ ).
Oils and viscous liquids ( P r ≫ 1 Pr \gg 1 P r ≫ 1 , e.g., P r > 100 Pr > 100 P r > 100 ) : Momentum diffuses far into the fluid while thermal diffusion is confined to a thin sublayer adjacent to the wall ( δ t ≪ δ \delta_t \ll \delta δ t ≪ δ ). Convective thermal resistance is concentrated almost entirely in this thin thermal film.
2. Core Dimensionless Groups in Convective Transport
To generalize experimental heat transfer data across diverse fluids, temperatures, and vessel dimensions, chemical engineers formulate transport laws using dimensionless groups.
1. Nusselt Number ( N u Nu N u ) N u L ≡ h L k f = Convective Heat Transfer Pure Molecular Conduction across fluid layer of thickness L Nu_L \equiv \frac{h L}{k_f} = \frac{\text{Convective Heat Transfer}}{\text{Pure Molecular Conduction across fluid layer of thickness } L} N u L ≡ k f h L = Pure Molecular Conduction across fluid layer of thickness L Convective Heat Transfer
Where k f k_f k f is the thermal conductivity of the fluid (not the solid wall) and L L L is characteristic length.
2. Reynolds Number ( R e Re R e ) R e D ≡ ρ v D μ = v D ν = 4 m ˙ π D μ Re_D \equiv \frac{\rho v D}{\mu} = \frac{v D}{\nu} = \frac{4 \dot{m}}{\pi D \mu} R e D ≡ μ ρ v D = ν v D = π D μ 4 m ˙
Represents the ratio of dynamic inertial forces to viscous shear forces. In circular pipe flow:
R e < 2 , 300 Re < 2,300 R e < 2 , 300 : Laminar flow.
2 , 300 ≤ R e ≤ 10 , 000 2,300 \le Re \le 10,000 2 , 300 ≤ R e ≤ 10 , 000 : Transition regime.
R e > 10 , 000 Re > 10,000 R e > 10 , 000 : Fully developed turbulent flow.
3. Prandtl Number ( P r Pr P r ) P r ≡ C p μ k f = ν α = Momentum Diffusivity Thermal Diffusivity Pr \equiv \frac{C_p \mu}{k_f} = \frac{\nu}{\alpha} = \frac{\text{Momentum Diffusivity}}{\text{Thermal Diffusivity}} P r ≡ k f C p μ = α ν = Thermal Diffusivity Momentum Diffusivity
A pure fluid property ratio independent of flow geometry or velocity.
4. Grashof Number ( G r Gr G r ) & Rayleigh Number ( R a Ra R a ) G r L ≡ g β ( T s − T ∞ ) L 3 ν 2 = Buoyancy Forces Viscous Forces Gr_L \equiv \frac{g \beta (T_s - T_\infty) L^3}{\nu^2} = \frac{\text{Buoyancy Forces}}{\text{Viscous Forces}} G r L ≡ ν 2 g β ( T s − T ∞ ) L 3 = Viscous Forces Buoyancy Forces R a L ≡ G r L ⋅ P r = g β ( T s − T ∞ ) L 3 ν α Ra_L \equiv Gr_L \cdot Pr = \frac{g \beta (T_s - T_\infty) L^3}{\nu \alpha} R a L ≡ G r L ⋅ P r = να g β ( T s − T ∞ ) L 3
Governs natural (buoyancy-driven) convection. Here β \beta β is the volumetric thermal expansion coefficient ( K − 1 \text{K}^{-1} K − 1 ):
For ideal gases: β = 1 T a b s \beta = \frac{1}{T_{abs}} β = T ab s 1 (where T a b s T_{abs} T ab s is in Kelvin or Rankine).
For liquids: β = − 1 ρ ( ∂ ρ ∂ T ) P \beta = -\frac{1}{\rho}\left(\frac{\partial \rho}{\partial T}\right)_P β = − ρ 1 ( ∂ T ∂ ρ ) P obtained from property tables.
5. Stanton Number ( S t St St ) & Colburn j H j_H j H Factor S t ≡ N u R e ⋅ P r = h ρ C p v St \equiv \frac{Nu}{Re \cdot Pr} = \frac{h}{\rho C_p v} St ≡ R e ⋅ P r N u = ρ C p v h j H ≡ S t ⋅ P r 2 / 3 = f 2 (Reynolds-Colburn Analogy) j_H \equiv St \cdot Pr^{2/3} = \frac{f}{2} \quad \text{(Reynolds-Colburn Analogy)} j H ≡ St ⋅ P r 2/3 = 2 f (Reynolds-Colburn Analogy)
Where f f f is the Fanning friction factor, directly linking fluid friction to convective heat transfer.
3. Forced Convection in Circular Pipes & Internal Ducts
In chemical process piping and shell-and-tube exchangers, fluids are pumped through tubes under forced convection.
Laminar Internal Flow ( R e < 2 , 300 Re < 2,300 R e < 2 , 300 )
In laminar flow through a circular pipe of diameter D D D , after the thermal entrance length ( L t , l a m ≈ 0.05 R e D P r L_{t,lam} \approx 0.05 Re D Pr L t , l am ≈ 0.05 R eD P r ), the flow becomes thermally fully developed. The Nusselt number asymptotically approaches exact analytical constants that depend solely on the thermal boundary condition at the tube wall:
Uniform Wall Heat Flux ( q ′ ′ = constant q'' = \text{constant} q ′′ = constant ) (e.g., electric resistance heating): N u D = h D k f = 48 11 ≈ 4.364 Nu_D = \frac{h D}{k_f} = \frac{48}{11} \approx \mathbf{4.364} N u D = k f h D = 11 48 ≈ 4.364
Uniform Wall Temperature ( T s = constant T_s = \text{constant} T s = constant ) (e.g., condensing steam or boiling refrigerant on the outer tube surface): N u D = h D k f ≈ 3.657 Nu_D = \frac{h D}{k_f} \approx \mathbf{3.657} N u D = k f h D ≈ 3.657
Important
In thermally fully developed laminar flow, the heat transfer coefficient h = N u ⋅ k f / D h = Nu \cdot k_f / D h = N u ⋅ k f / D is completely independent of fluid velocity and pipe length ! Doubling the volumetric flow rate has zero effect on h h h as long as the flow remains laminar.
- Turbulent Internal Flow ( R e > 10 , 000 Re > 10,000 R e > 10 , 000 )
- 1. Dittus-Boelter Correlation
The most frequently tested convective correlation on the PE exam. Valid for fully developed turbulent flow in smooth tubes with moderate temperature differences ( R e D ≥ 10 , 000 Re_D \ge 10,000 R e D ≥ 10 , 000 , 0.7 ≤ P r ≤ 160 0.7 \le Pr \le 160 0.7 ≤ P r ≤ 160 , L / D ≥ 10 L/D \ge 10 L / D ≥ 10 ): N u D = 0.023 R e D 0.8 P r n Nu_D = 0.023 Re_D^{0.8} Pr^n N u D = 0.023 R e D 0.8 P r n
Where the exponent n n n depends on the direction of heat transfer:
n = 0.4 n = 0.4 n = 0.4 for HEATING the fluid ( T w a l l > T b u l k T_{wall} > T_{bulk} T w a ll > T b u l k ).
n = 0.3 n = 0.3 n = 0.3 for COOLING the fluid ( T w a l l < T b u l k T_{wall} < T_{bulk} T w a ll < T b u l k ).
Property Evaluation : All fluid properties ( ρ , μ , C p , k \rho, \mu, C_p, k ρ , μ , C p , k ) are evaluated at the bulk mean fluid temperature T b = ( T i n + T o u t ) / 2 T_b = (T_{in} + T_{out})/2 T b = ( T in + T o u t ) /2 .
2. Sieder-Tate Correlation
When fluids exhibit large temperature differences between the bulk fluid and the pipe wall, steep radial viscosity gradients distort the velocity profile. Sieder and Tate introduced a viscosity ratio correction: N u D = 0.027 R e D 0.8 P r 1 / 3 ( μ b μ w ) 0.14 Nu_D = 0.027 Re_D^{0.8} Pr^{1/3} \left( \frac{\mu_b}{\mu_w} \right)^{0.14} N u D = 0.027 R e D 0.8 P r 1/3 ( μ w μ b ) 0.14
Where:
μ b \mu_b μ b is the dynamic viscosity evaluated at the bulk fluid temperature T b T_b T b .
μ w \mu_w μ w is the dynamic viscosity evaluated at the tube wall surface temperature T w T_w T w .
All other thermophysical properties ( ρ , C p , k \rho, C_p, k ρ , C p , k ) are evaluated at T b T_b T b .
Valid for 0.7 ≤ P r ≤ 16 , 700 0.7 \le Pr \le 16,700 0.7 ≤ P r ≤ 16 , 700 and R e D ≥ 10 , 000 Re_D \ge 10,000 R e D ≥ 10 , 000 .
3. Gnielinski Correlation
For higher precision, particularly in the lower turbulent and transition regimes ( 3 , 000 ≤ R e D ≤ 5 × 10 6 3,000 \le Re_D \le 5 \times 10^6 3 , 000 ≤ R e D ≤ 5 × 1 0 6 and 0.5 ≤ P r ≤ 2 , 000 0.5 \le Pr \le 2,000 0.5 ≤ P r ≤ 2 , 000 ): N u D = ( f / 8 ) ( R e D − 1000 ) P r 1 + 12.7 f / 8 ( P r 2 / 3 − 1 ) Nu_D = \frac{(f/8)(Re_D - 1000) Pr}{1 + 12.7 \sqrt{f/8} \left( Pr^{2/3} - 1 \right)} N u D = 1 + 12.7 f /8 ( P r 2/3 − 1 ) ( f /8 ) ( R e D − 1000 ) P r
Where the Darcy friction factor f f f for smooth pipes is given by Petukhov's equation: f = ( 0.790 ln ( R e D ) − 1.64 ) − 2 f = \left( 0.790 \ln(Re_D) - 1.64 \right)^{-2} f = ( 0.790 ln ( R e D ) − 1.64 ) − 2
- 4. Forced Convection Over External Geometries
- Flow Normal to a Single Circular Cylinder
For cross-flow of fluid past the exterior of a bare process pipe or thermowell, the Churchill-Bernstein correlation covers all R e D P r > 0.2 Re_D Pr > 0.2 R e D P r > 0.2 : N u D = 0.3 + 0.62 R e D 1 / 2 P r 1 / 3 [ 1 + ( 0.4 / P r ) 2 / 3 ] 1 / 4 [ 1 + ( R e D 282 , 000 ) 5 / 8 ] 4 / 5 Nu_D = 0.3 + \frac{0.62 Re_D^{1/2} Pr^{1/3}}{\left[ 1 + (0.4/Pr)^{2/3} \right]^{1/4}} \left[ 1 + \left( \frac{Re_D}{282,000} \right)^{5/8} \right]^{4/5} N u D = 0.3 + [ 1 + ( 0.4/ P r ) 2/3 ] 1/4 0.62 R e D 1/2 P r 1/3 [ 1 + ( 282 , 000 R e D ) 5/8 ] 4/5
Properties are evaluated at the film temperature T f = ( T s + T ∞ ) / 2 T_f = (T_s + T_\infty)/2 T f = ( T s + T ∞ ) /2 .
Flow Across Tube Banks (Shell-and-Tube Exchanger Shell-Side)
In shell-and-tube exchangers, fluid flows transversely across bundles of tubes arranged in either in-line or staggered pitch layouts. The general empirical correlation takes the form: N u D = C ⋅ R e D , m a x m P r 0.36 ( P r P r w ) 0.25 Nu_D = C \cdot Re_{D,max}^m Pr^{0.36} \left( \frac{Pr}{Pr_w} \right)^{0.25} N u D = C ⋅ R e D , ma x m P r 0.36 ( P r w P r ) 0.25
Where R e D , m a x = ρ v m a x D / μ Re_{D,max} = \rho v_{max} D / \mu R e D , ma x = ρ v ma x D / μ is based on the maximum fluid velocity occurring at the minimum free-flow area between adjacent tubes.
5. Natural (Free) Convection & Buoyancy-Driven Transport
When no external pumping device is present, fluid motion is induced purely by density differences caused by temperature gradients in a gravity field. Hot fluid near a heated surface expands, becomes less dense than the surrounding fluid, and rises due to buoyant force.
Reference Temperature for Natural Convection
All fluid properties ( ρ , μ , ν , C p , k , β \rho, \mu, \nu, C_p, k, \beta ρ , μ , ν , C p , k , β ) in natural convection correlations must be evaluated at the film temperature : T f = T s + T ∞ 2 T_f = \frac{T_s + T_\infty}{2} T f = 2 T s + T ∞
Vertical Plates and Vertical Cylinders
For vertical heat exchanger walls, tank sides, and vertical pipes, the Churchill-Chu correlation applies across all Rayleigh numbers ( 10 − 1 < R a L < 10 12 10^{-1} < Ra_L < 10^{12} 1 0 − 1 < R a L < 1 0 12 ): N u L = { 0.825 + 0.387 R a L 1 / 6 [ 1 + ( 0.492 / P r ) 9 / 16 ] 8 / 27 } 2 Nu_L = \left\{ 0.825 + \frac{0.387 Ra_L^{1/6}}{\left[ 1 + (0.492/Pr)^{9/16} \right]^{8/27}} \right\}^2 N u L = { 0.825 + [ 1 + ( 0.492/ P r ) 9/16 ] 8/27 0.387 R a L 1/6 } 2
For quick calculations on the PE exam, standard simplified power-law correlations are commonly used:
Laminar Regime ( 10 4 ≤ R a L ≤ 10 9 10^4 \le Ra_L \le 10^9 1 0 4 ≤ R a L ≤ 1 0 9 ) : N u L = 0.59 R a L 1 / 4 ⟹ h ∝ ( Δ T L ) 1 / 4 Nu_L = 0.59 Ra_L^{1/4} \implies h \propto \left(\frac{\Delta T}{L}\right)^{1/4} N u L = 0.59 R a L 1/4 ⟹ h ∝ ( L Δ T ) 1/4
Turbulent Regime ( 10 9 < R a L ≤ 10 13 10^9 < Ra_L \le 10^{13} 1 0 9 < R a L ≤ 1 0 13 ) : N u L = 0.10 R a L 1 / 3 ⟹ h ∝ Δ T 1 / 3 (independent of height L ! ) Nu_L = 0.10 Ra_L^{1/3} \implies h \propto \Delta T^{1/3} \quad \text{(independent of height } L!) N u L = 0.10 R a L 1/3 ⟹ h ∝ Δ T 1/3 (independent of height L !)
Horizontal Cylinders
For horizontal process pipes exposed to stagnant air, the Churchill-Chu correlation for horizontal cylinders is: N u D = { 0.60 + 0.387 R a D 1 / 6 [ 1 + ( 0.559 / P r ) 9 / 16 ] 8 / 27 } 2 ( 10 − 5 < R a D < 10 12 ) Nu_D = \left\{ 0.60 + \frac{0.387 Ra_D^{1/6}}{\left[ 1 + (0.559/Pr)^{9/16} \right]^{8/27}} \right\}^2 \quad (10^{-5} < Ra_D < 10^{12}) N u D = { 0.60 + [ 1 + ( 0.559/ P r ) 9/16 ] 8/27 0.387 R a D 1/6 } 2 ( 1 0 − 5 < R a D < 1 0 12 )
6. Summary Table: Primary Convective Heat Transfer Correlations
Flow Configuration Regime / Criteria Governing Correlation Property Evaluation Temperature Important PE Notes
Circular Pipe (Internal) Laminar, fully developed ( R e < 2300 Re < 2300 R e < 2300 ) N u D = 4.364 Nu_D = 4.364 N u D = 4.364 ( q ′ ′ = const q'' = \text{const} q ′′ = const ); N u D = 3.657 Nu_D = 3.657 N u D = 3.657 ( T s = const T_s = \text{const} T s = const ) Bulk fluid: T b = ( T i n + T o u t ) / 2 T_b = (T_{in} + T_{out})/2 T b = ( T in + T o u t ) /2 Independent of R e Re R e , P r Pr P r , velocity, and pipe length
Circular Pipe (Internal) Turbulent ( R e > 10 4 Re > 10^4 R e > 1 0 4 , 0.7 ≤ P r ≤ 160 0.7 \le Pr \le 160 0.7 ≤ P r ≤ 160 ) N u D = 0.023 R e D 0.8 P r n Nu_D = 0.023 Re_D^{0.8} Pr^n N u D = 0.023 R e D 0.8 P r n Bulk fluid: T b T_b T b n = 0.4 n = 0.4 n = 0.4 for heating; n = 0.3 n = 0.3 n = 0.3 for cooling
Circular Pipe (Internal) Turbulent, large Δ T \Delta T Δ T across film N u D = 0.027 R e D 0.8 P r 1 / 3 ( μ b / μ w ) 0.14 Nu_D = 0.027 Re_D^{0.8} Pr^{1/3} (\mu_b / \mu_w)^{0.14} N u D = 0.027 R e D 0.8 P r 1/3 ( μ b / μ w ) 0.14 Bulk T b T_b T b ; wall μ w \mu_w μ w at T w T_w T w Sieder-Tate viscosity ratio accounts for film distortion
Circular Pipe (Internal) Transition to Turbulent ( 3000 ≤ R e ≤ 5 × 10 6 3000 \le Re \le 5\times 10^6 3000 ≤ R e ≤ 5 × 1 0 6 ) Gnielinski correlation Bulk fluid: T b T_b T b Superior accuracy near transition ( R e ≈ 3000 − 10000 Re \approx 3000-10000 R e ≈ 3000 − 10000 )
Vertical Flat Plate Natural Convection, Laminar ( 10 4 ≤ R a L ≤ 10 9 10^4 \le Ra_L \le 10^9 1 0 4 ≤ R a L ≤ 1 0 9 ) N u L = 0.59 R a L 1 / 4 Nu_L = 0.59 Ra_L^{1/4} N u L = 0.59 R a L 1/4 Film: T f = ( T s + T ∞ ) / 2 T_f = (T_s + T_\infty)/2 T f = ( T s + T ∞ ) /2 Boundary layer transition occurs at R a c ≈ 10 9 Ra_c \approx 10^9 R a c ≈ 1 0 9
Vertical Flat Plate Natural Convection, Turbulent ( 10 9 ≤ R a L ≤ 10 13 10^9 \le Ra_L \le 10^{13} 1 0 9 ≤ R a L ≤ 1 0 13 ) N u L = 0.10 R a L 1 / 3 Nu_L = 0.10 Ra_L^{1/3} N u L = 0.10 R a L 1/3 Film: T f = ( T s + T ∞ ) / 2 T_f = (T_s + T_\infty)/2 T f = ( T s + T ∞ ) /2 Heat transfer coefficient h h h is independent of height L L L
Horizontal Cylinder Natural Convection ( 10 − 5 ≤ R a D ≤ 10 12 10^{-5} \le Ra_D \le 10^{12} 1 0 − 5 ≤ R a D ≤ 1 0 12 ) Churchill-Chu horizontal cylinder correlation Film: T f = ( T s + T ∞ ) / 2 T_f = (T_s + T_\infty)/2 T f = ( T s + T ∞ ) /2 For ideal gases, β = 1 / T f \beta = 1/T_f β = 1/ T f with T f T_f T f in Kelvin/Rankine
7. Comprehensive Worked Numerical Example: Forced Convection Heating of a Hydrocarbon Stream in a Reboiler Tube
Problem Statement
Liquid toluene ( M W = 92.14 kg/kmol MW = 92.14\text{ kg/kmol} M W = 92.14 kg/kmol ) flows through a commercial stainless steel reboiler tube with inside diameter D = 0.0525 m D = 0.0525\text{ m} D = 0.0525 m ( 52.5 mm 52.5\text{ mm} 52.5 mm , 2-inch Sch 40) and length L = 6.00 m L = 6.00\text{ m} L = 6.00 m . The mass flow rate is m ˙ = 4.20 kg/s \dot{m} = 4.20\text{ kg/s} m ˙ = 4.20 kg/s .
The toluene enters at 50.0 ∘ C 50.0^\circ\text{C} 50. 0 ∘ C and exits at 70.0 ∘ C 70.0^\circ\text{C} 70. 0 ∘ C , giving an arithmetic mean bulk temperature T b = 60.0 ∘ C T_b = 60.0^\circ\text{C} T b = 60. 0 ∘ C ( 333.15 K 333.15\text{ K} 333.15 K ). Condensing steam on the outside of the tube maintains the inside tube wall at a uniform surface temperature T w = 100.0 ∘ C T_w = 100.0^\circ\text{C} T w = 100. 0 ∘ C ( 373.15 K 373.15\text{ K} 373.15 K ).
Thermophysical Properties of Liquid Toluene:
At bulk temperature T b = 60.0 ∘ C T_b = 60.0^\circ\text{C} T b = 60. 0 ∘ C ( 333.15 K 333.15\text{ K} 333.15 K ):
Density: ρ = 830.0 kg/m 3 \rho = 830.0\text{ kg/m}^3 ρ = 830.0 kg/m 3
Dynamic viscosity: μ b = 0.380 × 10 − 3 Pa ⋅ s \mu_b = 0.380 \times 10^{-3}\text{ Pa}\cdot\text{s} μ b = 0.380 × 1 0 − 3 Pa ⋅ s ( 0.380 cP 0.380\text{ cP} 0.380 cP )
Thermal conductivity: k f = 0.125 W/(m ⋅ K) k_f = 0.125\text{ W/(m}\cdot\text{K)} k f = 0.125 W/(m ⋅ K)
Specific heat capacity: C p = 1 , 840 J/(kg ⋅ K) C_p = 1,840\text{ J/(kg}\cdot\text{K)} C p = 1 , 840 J/(kg ⋅ K)
At wall temperature T w = 100.0 ∘ C T_w = 100.0^\circ\text{C} T w = 100. 0 ∘ C ( 373.15 K 373.15\text{ K} 373.15 K ):
Dynamic viscosity: μ w = 0.260 × 10 − 3 Pa ⋅ s \mu_w = 0.260 \times 10^{-3}\text{ Pa}\cdot\text{s} μ w = 0.260 × 1 0 − 3 Pa ⋅ s ( 0.260 cP 0.260\text{ cP} 0.260 cP )
Calculate:
The mean flow velocity v v v and the Reynolds number R e D Re_D R e D . Identify the flow regime.
The Prandtl number P r Pr P r of the liquid toluene at bulk temperature.
The Nusselt number N u D B Nu_{DB} N u D B and heat transfer coefficient h D B h_{DB} h D B using the Dittus-Boelter correlation .
The Nusselt number N u S T Nu_{ST} N u ST and heat transfer coefficient h S T h_{ST} h ST using the Sieder-Tate correlation with viscosity ratio correction.
The total convective heat transfer rate q q q using the Sieder-Tate coefficient.
Step 1: Flow Velocity & Reynolds Number
Cross-sectional flow area of the circular tube: A c = π 4 D 2 = π 4 ( 0.0525 m ) 2 = 0.0021648 m 2 A_c = \frac{\pi}{4} D^2 = \frac{\pi}{4} (0.0525\text{ m})^2 = 0.0021648\text{ m}^2 A c = 4 π D 2 = 4 π ( 0.0525 m ) 2 = 0.0021648 m 2
Mean fluid velocity: v = m ˙ ρ A c = 4.20 kg/s ( 830.0 kg/m 3 ) ( 0.0021648 m 2 ) = 4.20 1.79678 = 2.3375 m/s v = \frac{\dot{m}}{\rho A_c} = \frac{4.20\text{ kg/s}}{(830.0\text{ kg/m}^3)(0.0021648\text{ m}^2)} = \frac{4.20}{1.79678} = \mathbf{2.3375\text{ m/s}} v = ρ A c m ˙ = ( 830.0 kg/m 3 ) ( 0.0021648 m 2 ) 4.20 kg/s = 1.79678 4.20 = 2.3375 m/s
Reynolds number: R e D = ρ v D μ b = 4 m ˙ π D μ b Re_D = \frac{\rho v D}{\mu_b} = \frac{4 \dot{m}}{\pi D \mu_b} R e D = μ b ρ v D = π D μ b 4 m ˙ R e D = 4 ( 4.20 kg/s ) π ( 0.0525 m ) ( 0.380 × 10 − 3 Pa ⋅ s ) = 16.80 6.26748 × 10 − 5 = 268 , 050 Re_D = \frac{4 (4.20\text{ kg/s})}{\pi (0.0525\text{ m})(0.380 \times 10^{-3}\text{ Pa}\cdot\text{s})} = \frac{16.80}{6.26748 \times 10^{-5}} = \mathbf{268,050} R e D = π ( 0.0525 m ) ( 0.380 × 1 0 − 3 Pa ⋅ s ) 4 ( 4.20 kg/s ) = 6.26748 × 1 0 − 5 16.80 = 268 , 050
Since R e D = 268 , 050 ≫ 10 , 000 Re_D = 268,050 \gg 10,000 R e D = 268 , 050 ≫ 10 , 000 and L / D = 6.00 / 0.0525 = 114.3 > 10 L/D = 6.00 / 0.0525 = 114.3 > 10 L / D = 6.00/0.0525 = 114.3 > 10 , the flow is fully developed turbulent flow .
Step 2: Prandtl Number P r = C p μ b k f = ( 1 , 840 J/(kg ⋅ K) ) ( 0.380 × 10 − 3 Pa ⋅ s ) 0.125 W/(m ⋅ K) = 0.6992 0.125 = 5.5936 ≈ 5.594 Pr = \frac{C_p \mu_b}{k_f} = \frac{(1,840\text{ J/(kg}\cdot\text{K)})(0.380 \times 10^{-3}\text{ Pa}\cdot\text{s})}{0.125\text{ W/(m}\cdot\text{K)}} = \frac{0.6992}{0.125} = \mathbf{5.5936} \approx \mathbf{5.594} P r = k f C p μ b = 0.125 W/(m ⋅ K) ( 1 , 840 J/(kg ⋅ K) ) ( 0.380 × 1 0 − 3 Pa ⋅ s ) = 0.125 0.6992 = 5.5936 ≈ 5.594
Step 3: Dittus-Boelter Heat Transfer Coefficient
Because the tube wall ( 100 ∘ C 100^\circ\text{C} 10 0 ∘ C ) is hotter than the bulk fluid ( 60 ∘ C 60^\circ\text{C} 6 0 ∘ C ), the fluid is being heated . Therefore, we select the heating exponent n = 0.4 n = 0.4 n = 0.4 : N u D B = 0.023 R e D 0.8 P r 0.4 Nu_{DB} = 0.023 Re_D^{0.8} Pr^{0.4} N u D B = 0.023 R e D 0.8 P r 0.4 R e D 0.8 = ( 268 , 050 ) 0.8 = 22 , 042.8 Re_D^{0.8} = (268,050)^{0.8} = 22,042.8 R e D 0.8 = ( 268 , 050 ) 0.8 = 22 , 042.8 P r 0.4 = ( 5.5936 ) 0.4 = 1.9904 Pr^{0.4} = (5.5936)^{0.4} = 1.9904 P r 0.4 = ( 5.5936 ) 0.4 = 1.9904 N u D B = 0.023 × 22 , 042.8 × 1.9904 = 1 , 009.1 Nu_{DB} = 0.023 \times 22,042.8 \times 1.9904 = \mathbf{1,009.1} N u D B = 0.023 × 22 , 042.8 × 1.9904 = 1 , 009.1
Dittus-Boelter heat transfer coefficient: h D B = N u D B k f D = ( 1 , 009.1 ) ( 0.125 W/(m ⋅ K) ) 0.0525 m = 2 , 402.6 W/(m 2 ⋅ K) h_{DB} = \frac{Nu_{DB} k_f}{D} = \frac{(1,009.1)(0.125\text{ W/(m}\cdot\text{K)})}{0.0525\text{ m}} = \mathbf{2,402.6\text{ W/(m}^2\cdot\text{K)}} h D B = D N u D B k f = 0.0525 m ( 1 , 009.1 ) ( 0.125 W/(m ⋅ K) ) = 2 , 402.6 W/(m 2 ⋅ K)
Step 4: Sieder-Tate Heat Transfer Coefficient (Viscosity Correction) N u S T = 0.027 R e D 0.8 P r 1 / 3 ( μ b μ w ) 0.14 Nu_{ST} = 0.027 Re_D^{0.8} Pr^{1/3} \left( \frac{\mu_b}{\mu_w} \right)^{0.14} N u ST = 0.027 R e D 0.8 P r 1/3 ( μ w μ b ) 0.14 P r 1 / 3 = ( 5.5936 ) 1 / 3 = 1.7751 Pr^{1/3} = (5.5936)^{1/3} = 1.7751 P r 1/3 = ( 5.5936 ) 1/3 = 1.7751 μ b μ w = 0.380 × 10 − 3 0.260 × 10 − 3 = 1.4615 \frac{\mu_b}{\mu_w} = \frac{0.380 \times 10^{-3}}{0.260 \times 10^{-3}} = 1.4615 μ w μ b = 0.260 × 1 0 − 3 0.380 × 1 0 − 3 = 1.4615 ( μ b μ w ) 0.14 = ( 1.4615 ) 0.14 = 1.0546 \left( \frac{\mu_b}{\mu_w} \right)^{0.14} = (1.4615)^{0.14} = 1.0546 ( μ w μ b ) 0.14 = ( 1.4615 ) 0.14 = 1.0546 N u S T = 0.027 × 22 , 042.8 × 1.7751 × 1.0546 = 1 , 114.6 Nu_{ST} = 0.027 \times 22,042.8 \times 1.7751 \times 1.0546 = \mathbf{1,114.6} N u ST = 0.027 × 22 , 042.8 × 1.7751 × 1.0546 = 1 , 114.6
Sieder-Tate heat transfer coefficient: h S T = N u S T k f D = ( 1 , 114.6 ) ( 0.125 W/(m ⋅ K) ) 0.0525 m = 2 , 653.8 W/(m 2 ⋅ K) h_{ST} = \frac{Nu_{ST} k_f}{D} = \frac{(1,114.6)(0.125\text{ W/(m}\cdot\text{K)})}{0.0525\text{ m}} = \mathbf{2,653.8\text{ W/(m}^2\cdot\text{K)}} h ST = D N u ST k f = 0.0525 m ( 1 , 114.6 ) ( 0.125 W/(m ⋅ K) ) = 2 , 653.8 W/(m 2 ⋅ K)
Engineering Insight: Because the fluid is heated at the wall, the fluid near the wall is hotter and less viscous than the bulk fluid. This thins the viscous sublayer, steepens the velocity gradient at the surface, and increases the convective film coefficient by ( 2 , 653.8 − 2 , 402.6 ) / 2 , 402.6 = + 10.5 % (2,653.8 - 2,402.6)/2,402.6 = +10.5\% ( 2 , 653.8 − 2 , 402.6 ) /2 , 402.6 = + 10.5% . Sieder-Tate properly accounts for this enhancement.
Step 5: Total Heat Transfer Rate
Inside tube surface area: A s = π D L = π ( 0.0525 m ) ( 6.00 m ) = 0.98960 m 2 A_s = \pi D L = \pi (0.0525\text{ m})(6.00\text{ m}) = \mathbf{0.98960\text{ m}^2} A s = π D L = π ( 0.0525 m ) ( 6.00 m ) = 0.98960 m 2
Driving temperature difference: Δ T = T w − T b = 100.0 ∘ C − 60.0 ∘ C = 40.0 K \Delta T = T_w - T_b = 100.0^\circ\text{C} - 60.0^\circ\text{C} = 40.0\text{ K} Δ T = T w − T b = 100. 0 ∘ C − 60. 0 ∘ C = 40.0 K
Total convective heat transfer rate: q = h S T A s Δ T = ( 2 , 653.8 W/(m 2 ⋅ K) ) ( 0.98960 m 2 ) ( 40.0 K ) = 105 , 045 W = 105.0 kW q = h_{ST} A_s \Delta T = (2,653.8\text{ W/(m}^2\cdot\text{K)})(0.98960\text{ m}^2)(40.0\text{ K}) = \mathbf{105,045\text{ W}} = \mathbf{105.0\text{ kW}} q = h ST A s Δ T = ( 2 , 653.8 W/(m 2 ⋅ K) ) ( 0.98960 m 2 ) ( 40.0 K ) = 105 , 045 W = 105.0 kW
Checking energy balance on toluene stream: q = m ˙ C p ( T o u t − T i n ) = ( 4.20 kg/s ) ( 1 , 840 J/(kg ⋅ K) ) ( 70.0 − 50.0 ) = ( 4.20 ) ( 1840 ) ( 20.0 ) = 154 , 560 W q = \dot{m} C_p (T_{out} - T_{in}) = (4.20\text{ kg/s})(1,840\text{ J/(kg}\cdot\text{K)})(70.0 - 50.0) = (4.20)(1840)(20.0) = 154,560\text{ W} q = m ˙ C p ( T o u t − T in ) = ( 4.20 kg/s ) ( 1 , 840 J/(kg ⋅ K) ) ( 70.0 − 50.0 ) = ( 4.20 ) ( 1840 ) ( 20.0 ) = 154 , 560 W
(Note: For an exact match, the log-mean temperature difference Δ T l m \Delta T_{lm} Δ T l m would be used across the tube length; this example uses arithmetic mean Δ T \Delta T Δ T to focus on local film evaluation).
- 8. Critical PE Exam Traps & Pitfalls
- Trap 1: Dittus-Boelter Exponent Selection ( n = 0.4 n = 0.4 n = 0.4 vs. n = 0.3 n = 0.3 n = 0.3 )
Always verify whether the fluid is being heated or cooled . If fluid enters cold and exits hot ( T w > T b T_w > T_b T w > T b ), the fluid is heated ⟹ n = 0.4 \implies n = 0.4 ⟹ n = 0.4 . If hot process fluid is cooled by cooling water ( T w < T b T_w < T_b T w < T b ), the fluid is cooled ⟹ n = 0.3 \implies n = 0.3 ⟹ n = 0.3 . Using n = 0.4 n=0.4 n = 0.4 for a cooling application overpredicts h h h by 15 − 20 % 15-20\% 15 − 20% and leads directly to an undersized heat exchanger.
Trap 2: Property Evaluation Temperature ( T b T_b T b vs. T f T_f T f )
Internal Forced Convection (Dittus-Boelter, Sieder-Tate) : Evaluate fluid properties at the bulk mean temperature T b = ( T i n + T o u t ) / 2 T_b = (T_{in} + T_{out})/2 T b = ( T in + T o u t ) /2 .
External Forced Convection & All Natural Convection : Evaluate fluid properties at the film temperature T f = ( T s + T ∞ ) / 2 T_f = (T_s + T_\infty)/2 T f = ( T s + T ∞ ) /2 .
Trap 3: Ideal Gas β \beta β in Natural Convection
When calculating the Grashof number for air or flue gas, β = 1 / T \beta = 1/T β = 1/ T . T T T must be absolute temperature ( K \text{K} K or ∘ R ^\circ\text{R} ∘ R ) ! Evaluating β = 1 / T [ ∘ C ] \beta = 1/T[^\circ\text{C}] β = 1/ T [ ∘ C ] produces an error of over 200 % 200\% 200% .
Trap 4: Forgetting the Constant Laminar Limits
Candidates frequently panic when an exam question states that a flow has R e = 800 Re = 800 R e = 800 and asks for N u Nu N u , searching for a non-existent velocity formula. Remember: for thermally fully developed laminar pipe flow, N u = 4.364 Nu = 4.364 N u = 4.364 (constant flux) or N u = 3.657 Nu = 3.657 N u = 3.657 (constant surface temperature), regardless of velocity!