Study guide
How to Use This Guide and the NCEES Handbook
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
How to Use This Guide and the NCEES Handbook
Key Takeaways Explain This Topic AI
Because the exam is closed book with an on-screen reference, the skill being tested is locating and applying a handbook relation under time pressure, not recalling it from memory.
Work every problem in the units the question gives you; the exam mixes SI and USCS deliberately, and unit conversion is one of the highest-frequency error sources on the PE Chemical exam.
Use a three-pass strategy across the 8-hour block: sweep for fast questions, return to medium-effort calculations, then spend what remains on the longest problems, leaving no question blank because there is no guessing penalty.
The two friction factor conventions are the classic PE trap: Darcy-Weisbach f D = 64 / R e f_D = 64/Re f D = 64/ R e in laminar flow versus Fanning f F = 16 / R e f_F = 16/Re f F = 16/ R e , with f D = 4 f F f_D = 4 f_F f D = 4 f F ; using the wrong one produces a 4x error in pressure drop.
This guide is organized so that Chapters 1-15 cover the six calculation-heavy knowledge areas and Chapters 16-20 cover Plant Design and Operation, the exam's largest area at 15-23 questions.
Last updated: September 2026
How to Use This Guide and the NCEES Handbook
The PE Chemical exam does not test whether you memorized the Colburn analogy. It tests whether, with an electronic handbook open and a clock running, you can identify the governing relation, recognize which variables the problem actually gave you, and execute cleanly in the units on the screen. That is a different skill from coursework, and it is trainable.
1. Practice the Way the Exam Works
Rule 1: Never solve a practice problem from memory. The handbook is provided; the exam assumes you will use it. If you solve from memory during practice, you never build the retrieval skill you actually need, and on exam day you will burn four minutes hunting for a correlation you should have found in twenty seconds.
Rule 2: Learn the handbook's organization, not its contents. You do not need to know that the Dittus-Boelter correlation is on a particular page. You need to know that convective correlations live in the heat transfer section, that they are indexed by geometry and by heating-versus-cooling, and that the exponent on the Prandtl number changes between the two cases. Structure beats page numbers.
Rule 3: Build a nomenclature reflex. The largest silent error source on this exam is a symbol collision. (k) is a thermal conductivity, a reaction rate constant, an isentropic exponent, and a mass-transfer coefficient depending on the chapter. C p C_p C p is a heat capacity; C v C_v C v is either a constant-volume heat capacity or a control valve flow coefficient. Read the problem's stated units to disambiguate the symbol before you write anything down.
2. Units: The Exam Mixes Them on Purpose
The specification explicitly states the exam uses both SI and USCS. In practice this means:
Quantity SI form you will see USCS form you will see
Pressure kPa \text{kPa} kPa , bar \text{bar} bar , MPa \text{MPa} MPa psia \text{psia} psia , psig \text{psig} psig , in H 2 O \text{in H}_2\text{O} in H 2 O
Heat flux W/m 2 \text{W/m}^2 W/m 2 Btu/(hr ⋅ ft 2 ) \text{Btu/(hr}\cdot\text{ft}^2) Btu/(hr ⋅ ft 2 )
Overall coefficient (U) W/(m 2 ⋅ K) \text{W/(m}^2\cdot\text{K)} W/(m 2 ⋅ K) Btu/(hr ⋅ ft 2 ⋅ ∘ F) \text{Btu/(hr}\cdot\text{ft}^2\cdot^\circ\text{F)} Btu/(hr ⋅ ft 2 ⋅ ∘ F)
Corrosion rate mm/yr \text{mm/yr} mm/yr mpy \text{mpy} mpy (mils per year)
Volumetric flow m 3 /s \text{m}^3\text{/s} m 3 /s gpm \text{gpm} gpm , acfm \text{acfm} acfm , scfm \text{scfm} scfm
Three unit disciplines will save you more points than any single technical topic:
Convert temperature to absolute before any ratio or any radiation calculation. β = 1 / T \beta = 1/T β = 1/ T requires kelvin. σ T 4 \sigma T^4 σ T 4 requires kelvin or rankine. Using ∘ C ^\circ\text{C} ∘ C in a thermal expansion coefficient produces errors well over 100%.
Distinguish gauge from absolute. Every choked-flow, compressibility, and relief-sizing calculation needs absolute pressure. A relief valve set at 250 psig 250\text{ psig} 250 psig relieves at 1.10 × 250 + 14.7 = 289.7 psia 1.10 \times 250 + 14.7 = 289.7\text{ psia} 1.10 × 250 + 14.7 = 289.7 psia .
Distinguish mass from mole. A stream given as wt% \text{wt\%} wt% and a stream given as mol% \text{mol\%} mol% are different streams. Convert once, at the top of the page, and label it.
3. The Friction Factor Trap (and Its Relatives)
Some conventions have two coexisting definitions, and the exam knows it. Learn these four pairs cold:
Convention A Convention B Relationship
Darcy-Weisbach f D = 64 / R e f_D = 64/Re f D = 64/ R e (laminar) Fanning f F = 16 / R e f_F = 16/Re f F = 16/ R e f D = 4 f F f_D = 4 f_F f D = 4 f F
Colburn j D = f Fanning / 2 j_D = f_{\text{Fanning}}/2 j D = f Fanning /2 — j D = f Darcy / 8 j_D = f_{\text{Darcy}}/8 j D = f Darcy /8
Antoine with log 10 \log_{10} lo g 10 Antoine with ln \ln ln Constants are not interchangeable
Enthalpy from steam tables Enthalpy from a formation-based table Different reference states; never mix in one Δ H \Delta H Δ H
The Darcy/Fanning error is worth a factor of four in pressure drop and is the most commonly planted distractor in fluids questions. The reference-state error is subtler: subtracting a steam-table enthalpy from a NIST formation-based enthalpy for water introduces an offset of roughly 105 kJ/kg 105\text{ kJ/kg} 105 kJ/kg that no amount of careful arithmetic will reveal. Always compute a Δ H \Delta H Δ H from a single consistent source.
4. Pacing: A Three-Pass Strategy for 8 Hours
With 6 minutes per question on average, the distribution matters more than the mean. Some questions are 90-second definition or judgment calls; some are 12-minute multi-step balances. A single linear pass wastes your best thinking on whichever hard problem happens to appear early. PASS 1 (~150 min, questions 1-80)
Answer everything solvable in under ~3 minutes.
Flag anything longer. Expect to clear 35-45 questions.
- |
- v [take the scheduled break here]
- PASS 2 (~220 min)
- Work the flagged medium problems: single-concept
calculations needing a handbook lookup.
- |
- v
- PASS 3 (~110 min)
Longest multi-step problems + verification sweep.
Confirm no question is left blank.
Rules that make this work:
Answer before you flag. Put your best guess in even on a flagged question. If you run out of time, you still have a shot; there is no guessing penalty.
Enforce a hard abandon rule. If a question has consumed 10 minutes without converging, mark your best answer, flag it, and move on. One 25-minute problem costs you four other questions.
Sanity-check magnitudes, not digits. A (U) of 5,000 W/(m 2 ⋅ K) 5{,}000\text{ W/(m}^2\cdot\text{K)} 5 , 000 W/(m 2 ⋅ K) for a gas-gas exchanger is wrong by two orders of magnitude and can be rejected without redoing the arithmetic. Distractors are usually built from specific procedural mistakes (wrong friction factor convention, missing the 4 × 4\times 4 × , forgetting absolute temperature), so an answer that is off by exactly 4x or exactly 2x should make you suspicious of your own work.
5. How This Guide Maps to the Specification
- Guide chapters Official knowledge area Questions
- 1-2 Mass/Energy Balances 12-18
- 3-4 Fluids 10-16
- 5-7 Thermodynamics 11-17
- 8-9 Heat Transfer 9-14
- 10-12 Mass Transfer 7-11
- 13-14 Chemical Reaction Engineering 6-10
- 15 Transport and physical properties supporting Fluids, Heat Transfer, and Thermodynamics —
- 16-20 Plant Design and Operation 15-23
Chapters 16 through 20 deserve a specific note. They cover materials of construction and corrosion, process safety and relief, inerting and containment, process control and economics, instrumentation and safety instrumented systems, PFDs and P&IDs and scale-up and siting, equipment selection and sizing and optimization, environmental emissions and remediation, operating procedures and startup/shutdown, mechanical integrity and reliability, and debottlenecking and troubleshooting. Every one of those is a named subtopic in the official specification, and together they are the largest block of questions on the exam. Do not treat them as an appendix.
Each section that follows ends with practice checks written in the exam's own style: a realistic scenario, four plausible options where the wrong ones encode specific procedural errors, and an explanation that shows the full path rather than just naming the winner.