Study guide

10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

PE Chemical Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the PE Chemical Exam How to Use This Guide and the NCEES Handbook

2 Chapter 1: Material Balances & Flowsheet Calculations

1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations

3 Chapter 2: Energy Balances & Thermochemistry

2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances

4 Chapter 3: Fluid Statics & Incompressible Pipe Flow

3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations

5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up

6 Chapter 5: Thermodynamic Laws & Fundamental Relations

5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations

7 Chapter 6: Real Gases & Equations of State

6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions

8 Chapter 7: Phase & Chemical Reaction Equilibria

7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation

9 Chapter 8: Heat Transfer Mechanisms & Conduction

8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange

10 Chapter 9: Heat Exchanger Design & Phase Change

9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances

11 Chapter 10: Mass Transfer Fundamentals & Diffusion

10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

12 Chapter 11: Distillation Operations

11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components

13 Chapter 12: Rate-Controlled & Equilibrium Separations

12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations

14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors

13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations

15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis

14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models

16 Chapter 15: Physical & Transport Properties of Fluids

15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles

17 Chapter 16: Materials of Construction & Corrosion

16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention

18 Chapter 17: Process Safety & Pressure Relief Systems

17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment

19 Chapter 18: Process Control & Engineering Economics

18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems

20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance

19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation

21 Chapter 20: Plant Operation, Reliability & Continuous Improvement

20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting

10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

Key Takeaways Explain This Topic AI

The Sherwood number (Sh = k_c * L / D_AB) represents the dimensionless ratio of convective mass transfer rate to pure molecular diffusive transport, directly paralleling the Nusselt number (Nu = h * L / k) in heat transfer.

The Schmidt number (Sc = mu / (rho * D_AB) = nu / D_AB) represents the ratio of momentum diffusivity (kinematic viscosity) to mass diffusivity, dictating the relative thickness of hydrodynamic and concentration boundary layers (delta_u / delta_c approx Sc^(1/3)), directly paralleling the Prandtl number (Pr = nu / alpha).

Typical Schmidt numbers differ by orders of magnitude between phases: gases exhibit Sc approx 0.5 to 2.5 (where hydrodynamic and concentration boundary layers are comparable, delta_u approx delta_c), whereas liquids exhibit Sc approx 500 to 5,000 (where the concentration boundary layer is 8 to 17 times thinner than the velocity boundary layer).

The Chilton-Colburn mass transfer j_D factor analogy establishes equivalence between momentum, heat, and mass transfer: j_D = (Sh / (Re * Sc^(1/3))) = (k_c / u) * Sc^(2/3) = j_H = (Nu / (Re * Pr^(1/3))) = f / 2, allowing direct calculation of mass transfer coefficients from Fanning friction factors (f) or heat transfer data.

For a single sphere or bubble suspended in a quiescent fluid (Re -> 0), the theoretical minimum Sherwood number is Sh = 2.0, derived analytically from 3D radial molecular diffusion; in flowing fluids, the Froessling/Ranz-Marshall correlation extends this to Sh = 2.0 + 0.60 * Re^(1/2) * Sc^(1/3).

Last updated: September 2026

10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

In chemical engineering transport phenomena, empirical mass transfer correlations are organized into dimensionless groups . This methodology allows laboratory data obtained on small-scale bench models using air-water systems to be scaled directly to multi-meter industrial reactors operating at high temperatures and pressures. On the NCEES PE Chemical Exam , mastery of mass transfer dimensionless numbers—and their profound analogies to heat and momentum transfer—enables engineers to solve complex rating problems rapidly without re-deriving microscopic transport balances.

1. Core Mass Transfer Dimensionless Groups +---------------------------------------------------------------------------------------+

  • | HEAT VS. MASS TRANSFER ANALOGIES |
  • +----------------------------+-----------------------------+----------------------------+
  • | MOMENTUM TRANSFER | HEAT TRANSFER | MASS TRANSFER |
  • +----------------------------+-----------------------------+----------------------------+
  • | Kinematic Viscosity (nu) | Thermal Diffusivity (alpha) | Mass Diffusivity (D_AB) |
  • | nu = mu / rho | alpha = k / (rho * Cp) | D_AB |
  • | Friction Factor (f / 2) | Nusselt Number (Nu = h*L/k) | Sherwood Number (Sh=kc*L/D)|
  • | Reynolds Number (Re) | Prandtl Number (Pr = nu/a) | Schmidt Number (Sc = nu/D) |
  • | Colburn j_M = f / 2 | Colburn j_H = Nu/(Re*Pr^1/3)| Colburn j_D = Sh/(Re*Sc^1/3|
  • +----------------------------+-----------------------------+----------------------------+
  • 1. Sherwood Number ( S h Sh S h )

The Sherwood number is the dimensionless convective mass transfer coefficient, representing the ratio of total convective mass transfer to pure molecular diffusion across characteristic length L L L : S h ≡ k c L D A B Sh \equiv \frac{k_c L}{D_{AB}} S h ≡ D A B ​ k c ​ L ​

Where:

k c k_c k c ​ = convective mass transfer coefficient ( m/s \text{m/s} m/s or ft/hr \text{ft/hr} ft/hr ).

L L L = characteristic geometric length (e.g., tube inner diameter D D D , particle diameter d p d_p d p ​ , plate length L L L ; in m \text{m} m or ft \text{ft} ft ).

D A B D_{AB} D A B ​ = binary molecular diffusivity ( m 2 / s \text{m}^2/\text{s} m 2 / s or ft 2 / hr \text{ft}^2/\text{hr} ft 2 / hr ).

Physical Meaning: If mass transfer occurred solely by pure steady-state molecular diffusion across a stagnant stagnant boundary film of thickness δ \delta δ , then k c = D A B / δ k_c = D_{AB} / \delta k c ​ = D A B ​ / δ . Substituting this yields S h = L / δ Sh = L / \delta S h = L / δ . Thus, the Sherwood number represents the ratio of the macroscopic system dimension to the concentration boundary layer thickness. It is the direct mass transfer analogue of the Nusselt number ( N u = h L / k Nu = h L / k N u = h L / k ).

2. Schmidt Number ( S c Sc S c )

The Schmidt number is the ratio of momentum diffusivity (kinematic viscosity, ν \nu ν ) to mass diffusivity ( D A B D_{AB} D A B ​ ): S c ≡ μ ρ D A B = ν D A B Sc \equiv \frac{\mu}{\rho D_{AB}} = \frac{\nu}{D_{AB}} S c ≡ ρ D A B ​ μ ​ = D A B ​ ν ​

Where:

μ \mu μ = dynamic fluid viscosity ( Pa ⋅ s = kg/(m ⋅ s) \text{Pa}\cdot\text{s} = \text{kg/(m}\cdot\text{s)} Pa ⋅ s = kg/(m ⋅ s) or lb/(ft ⋅ hr) \text{lb/(ft}\cdot\text{hr)} lb/(ft ⋅ hr) ).

ρ \rho ρ = fluid density ( kg/m 3 \text{kg/m}^3 kg/m 3 or lb/ft 3 \text{lb/ft}^3 lb/ft 3 ).

ν = μ / ρ \nu = \mu / \rho ν = μ / ρ = kinematic viscosity / momentum diffusivity ( m 2 / s \text{m}^2/\text{s} m 2 / s or ft 2 / hr \text{ft}^2/\text{hr} ft 2 / hr ).

Physical Meaning: The Schmidt number governs the relative rates of momentum and mass transport by molecular diffusion through fluid layers. It dictates the ratio of the hydrodynamic (velocity) boundary layer thickness ( δ u \delta_u δ u ​ ) to the concentration boundary layer thickness ( δ c \delta_c δ c ​ ): δ u δ c ≈ S c 1 / 3 \frac{\delta_u}{\delta_c} \approx Sc^{1/3} δ c ​ δ u ​ ​ ≈ S c 1/3

Phase Contrast on the PE Exam:

Gases: ν ≈ 10 − 5 m 2 / s \nu \approx 10^{-5}\text{ m}^2/\text{s} ν ≈ 1 0 − 5 m 2 / s , D A B ≈ 10 − 5 m 2 / s ⟹ S c ≈ 0.5 to 2.5 D_{AB} \approx 10^{-5}\text{ m}^2/\text{s} \implies \mathbf{Sc \approx 0.5\text{ to }2.5} D A B ​ ≈ 1 0 − 5 m 2 / s ⟹ Sc ≈ 0.5 to 2.5 .

In gas flows, momentum and mass diffuse at comparable rates. The velocity boundary layer and concentration boundary layer are roughly the same thickness ( δ u ≈ δ c \delta_u \approx \delta_c δ u ​ ≈ δ c ​ ).

Liquids: ν ≈ 10 − 6 m 2 / s \nu \approx 10^{-6}\text{ m}^2/\text{s} ν ≈ 1 0 − 6 m 2 / s , D A B ≈ 10 − 9 m 2 / s ⟹ S c ≈ 500 to 5 , 000 D_{AB} \approx 10^{-9}\text{ m}^2/\text{s} \implies \mathbf{Sc \approx 500\text{ to }5,000} D A B ​ ≈ 1 0 − 9 m 2 / s ⟹ Sc ≈ 500 to 5 , 000 .

In liquid flows, momentum diffuses hundreds or thousands of times faster than mass! Consequently, δ u / δ c ≈ ( 1 , 000 ) 1 / 3 = 10 \delta_u / \delta_c \approx (1,000)^{1/3} = 10 δ u ​ / δ c ​ ≈ ( 1 , 000 ) 1/3 = 10 . The concentration boundary layer is an ultra-thin film embedded deep within the viscous sublayer of the velocity boundary layer.

3. Mass Transfer Peclet Number ( P e m Pe_m P e m ​ )

The Peclet number for mass transfer characterizes the relative importance of convective bulk advection to molecular diffusion: P e m ≡ R e ⋅ S c = ( ρ u L μ ) ( μ ρ D A B ) = u L D A B Pe_m \equiv Re \cdot Sc = \left( \frac{\rho u L}{\mu} \right) \left( \frac{\mu}{\rho D_{AB}} \right) = \frac{u L}{D_{AB}} P e m ​ ≡ R e ⋅ S c = ( μ ρ uL ​ ) ( ρ D A B ​ μ ​ ) = D A B ​ uL ​

Where:

u u u = fluid superficial or bulk velocity ( m/s \text{m/s} m/s or ft/s \text{ft/s} ft/s ).

For P e m ≫ 1 Pe_m \gg 1 P e m ​ ≫ 1 : Bulk flow advection overwhelms molecular diffusion. Concentration changes are swept rapidly downstream.

For P e m ≪ 1 Pe_m \ll 1 P e m ​ ≪ 1 : Molecular diffusion dominates advective flow. Solute diffuses upstream against the bulk current.

4. Lewis Number ( L e Le L e )

The Lewis number compares thermal diffusivity ( α \alpha α ) to mass diffusivity ( D A B D_{AB} D A B ​ ): L e ≡ S c P r = α D A B = k ρ C p D A B Le \equiv \frac{Sc}{Pr} = \frac{\alpha}{D_{AB}} = \frac{k}{\rho C_p D_{AB}} L e ≡ P r S c ​ = D A B ​ α ​ = ρ C p ​ D A B ​ k ​

Where P r = ν / α Pr = \nu / \alpha P r = ν / α is the Prandtl number.

In air-water vapor mixtures at ambient atmospheric conditions, L e ≈ 1.0 Le \approx 1.0 L e ≈ 1.0 . This thermodynamic coincidence means heat and mass transfer boundary layers grow at identical rates, allowing the wet-bulb psychrometric temperature to equal the thermodynamic adiabatic saturation temperature.

5. Stanton Number for Mass Transfer ( S t m St_m S t m ​ )

The mass transfer Stanton number represents the ratio of mass transfer flux to the convective flux carried by the main flow: S t m ≡ S h R e ⋅ S c = k c u St_m \equiv \frac{Sh}{Re \cdot Sc} = \frac{k_c}{u} S t m ​ ≡ R e ⋅ S c S h ​ = u k c ​ ​

2. Transport Analogies: Reynolds and Chilton-Colburn

When mass transfer coefficients cannot be easily measured, chemical engineers rely on transport analogies to calculate k c k_c k c ​ directly from friction factors ( f f f ) or heat transfer coefficients ( h h h ).

1. Reynolds Analogy

Osborne Reynolds hypothesized that the mechanisms transferring momentum to a pipe wall are identical to those transferring heat or mass. For a smooth wall with zero pressure gradient: f 2 = h ρ C p u = k c u ⟹ f 2 = S t h = S t m \frac{f}{2} = \frac{h}{\rho C_p u} = \frac{k_c}{u} \implies \frac{f}{2} = St_h = St_m 2 f ​ = ρ C p ​ u h ​ = u k c ​ ​ ⟹ 2 f ​ = S t h ​ = S t m ​

Where f f f is the Fanning friction factor.

Strict Limitation: The Reynolds analogy is valid only when P r ≈ 1.0 Pr \approx 1.0 P r ≈ 1.0 and S c ≈ 1.0 Sc \approx 1.0 S c ≈ 1.0 , and where form drag (flow separation) is absent. It fails completely for liquids ( S c ≫ 1 Sc \gg 1 S c ≫ 1 ).

2. Chilton-Colburn j j j -Factor Analogy

T. H. Chilton and A. P. Colburn modified the Reynolds analogy by introducing empirical exponent factors ( S c 2 / 3 Sc^{2/3} S c 2/3 and P r 2 / 3 Pr^{2/3} P r 2/3 ) to account for boundary layer thickness differences across fluids: j D ≡ S t m ⋅ S c 2 / 3 = ( k c u ) S c 2 / 3 = S h R e ⋅ S c 1 / 3 \mathbf{j_D \equiv St_m \cdot Sc^{2/3} = \left( \frac{k_c}{u} \right) Sc^{2/3} = \frac{Sh}{Re \cdot Sc^{1/3}}} j D ​ ≡ S t m ​ ⋅ S c 2/3 = ( u k c ​ ​ ) S c 2/3 = Re ⋅ S c 1/3 Sh ​ j H ≡ S t h ⋅ P r 2 / 3 = ( h ρ C p u ) P r 2 / 3 = N u R e ⋅ P r 1 / 3 \mathbf{j_H \equiv St_h \cdot Pr^{2/3} = \left( \frac{h}{\rho C_p u} \right) Pr^{2/3} = \frac{Nu}{Re \cdot Pr^{1/3}}} j H ​ ≡ S t h ​ ⋅ P r 2/3 = ( ρ C p ​ u h ​ ) P r 2/3 = Re ⋅ P r 1/3 Nu ​ j D = j H = f 2 \mathbf{j_D = j_H = \frac{f}{2}} j D ​ = j H ​ = 2 f ​

Important

Fanning vs. Darcy Friction Factors in the Analogy:

The friction factor in the Chilton-Colburn analogy is strictly the Fanning friction factor ( f f f ). If the Moody / Darcy-Weisbach friction factor ( f D = 4 f f_D = 4f f D ​ = 4 f ) is used, the relationship becomes: j D = f D 8 j_D = \frac{f_D}{8} j D ​ = 8 f D ​ ​ Confusing f f f and f D f_D f D ​ is one of the most widespread numerical calculation errors on the NCEES PE Chemical exam, leading to a factor-of-four ( 400 % 400\% 400% ) error!

Range of Validity: The Chilton-Colburn analogy provides remarkable accuracy (±10%) across turbulent regimes in pipes, flat plates, and conduits for:

  • 0.6 ≤ S c ≤ 3 , 000 0.6 \le Sc \le 3,000 0.6 ≤ S c ≤ 3 , 000
  • 0.6 ≤ P r ≤ 10 , 000 0.6 \le Pr \le 10,000 0.6 ≤ P r ≤ 10 , 000
  • R e > 10 , 000 Re > 10,000 R e > 10 , 000
  • 3. Standard Empirical Correlations for Practical Engineering Geometries
  • 1. Mass Transfer from a Sphere in Stagnant Fluid ( R e = 0 Re = 0 R e = 0 )

Consider a spherical pellet or droplet of diameter d p d_p d p ​ suspended in an infinitely large quiescent fluid ( u = 0 u = 0 u = 0 ). In spherical coordinates, steady-state radial diffusion is governed by: d d r ( r 2 d C A d r ) = 0 \frac{d}{dr}\left( r^2 \frac{dC_A}{dr} \right) = 0 d r d ​ ( r 2 d r d C A ​ ​ ) = 0

Integrating from the sphere surface ( r = R = d p / 2 , C A = C A s r = R = d_p / 2, C_A = C_{As} r = R = d p ​ /2 , C A ​ = C A s ​ ) to infinity ( r → ∞ , C A = C A ∞ r \to \infty, C_A = C_{A\infty} r → ∞ , C A ​ = C A ∞ ​ ): C A ( r ) = C A ∞ + ( C A s − C A ∞ ) R r C_A(r) = C_{A\infty} + (C_{As} - C_{A\infty}) \frac{R}{r} C A ​ ( r ) = C A ∞ ​ + ( C A s ​ − C A ∞ ​ ) r R ​

The molar flux leaving the surface is: N A s = − D A B d C A d r ∣ r = R = − D A B [ − ( C A s − C A ∞ ) R R 2 ] = D A B R ( C A s − C A ∞ ) = 2 D A B d p ( C A s − C A ∞ ) N_{As} = -D_{AB} \left. \frac{dC_A}{dr} \right|_{r=R} = -D_{AB} \left[ -(C_{As} - C_{A\infty}) \frac{R}{R^2} \right] = \frac{D_{AB}}{R} (C_{As} - C_{A\infty}) = \frac{2 D_{AB}}{d_p} (C_{As} - C_{A\infty}) N A s ​ = − D A B ​ d r d C A ​ ​ ​ r = R ​ = − D A B ​ [ − ( C A s ​ − C A ∞ ​ ) R 2 R ​ ] = R D A B ​ ​ ( C A s ​ − C A ∞ ​ ) = d p ​ 2 D A B ​ ​ ( C A s ​ − C A ∞ ​ )

Equating this to convective flux N A s = k c ( C A s − C A ∞ ) N_{As} = k_c (C_{As} - C_{A\infty}) N A s ​ = k c ​ ( C A s ​ − C A ∞ ​ ) : k c = 2 D A B d p ⟹ S h = k c d p D A B = 2.0 k_c = \frac{2 D_{AB}}{d_p} \implies \mathbf{Sh = \frac{k_c d_p}{D_{AB}} = 2.0} k c ​ = d p ​ 2 D A B ​ ​ ⟹ Sh = D AB ​ k c ​ d p ​ ​ = 2.0

Note

The Asymptotic Limit S h = 2.0 Sh = 2.0 S h = 2.0 :

For a 3D sphere, the Sherwood number can never drop below 2.0 2.0 2.0 , no matter how slow the fluid moves! The value S h = 2.0 Sh = 2.0 S h = 2.0 represents the absolute lower thermodynamic bound for 3D steady-state radial molecular conduction.

2. Droplets, Bubbles, and Solid Spheres in Flow (Froessling / Ranz-Marshall)

When fluid flows past a sphere, forced convection augments molecular diffusion. The classic Froessling (or Ranz-Marshall ) correlation superimposes convective boundary layer thinning onto the conductive limit: S h = 2.0 + 0.60 ⋅ R e p 1 / 2 ⋅ S c 1 / 3 \mathbf{Sh = 2.0 + 0.60 \cdot Re_p^{1/2} \cdot Sc^{1/3}} Sh = 2.0 + 0.60 ⋅ R e p 1/2 ​ ⋅ S c 1/3

Where:

R e p = ρ u d p μ Re_p = \frac{\rho u d_p}{\mu} R e p ​ = μ ρ u d p ​ ​ = particle Reynolds number ( 0 ≤ R e p ≤ 200 0 \le Re_p \le 200 0 ≤ R e p ​ ≤ 200 ).

S c = μ ρ D A B Sc = \frac{\mu}{\rho D_{AB}} S c = ρ D A B ​ μ ​ ( 0.6 ≤ S c ≤ 250 0.6 \le Sc \le 250 0.6 ≤ S c ≤ 250 ).

This equation is identical in functional form to the Ranz-Marshall heat transfer equation: N u = 2.0 + 0.60 R e p 1 / 2 P r 1 / 3 Nu = 2.0 + 0.60 Re_p^{1/2} Pr^{1/3} N u = 2.0 + 0.60 R e p 1/2 ​ P r 1/3 .

3. Flow Inside Circular Tubes

For mass transfer to or from the inner wall of a smooth cylindrical tube of inner diameter D D D :

Laminar Flow ( R e < 2 , 100 Re < 2,100 R e < 2 , 100 ):

For fully developed velocity and concentration profiles with uniform wall concentration: S h = 3.66 Sh = 3.66 S h = 3.66

For uniform wall mass flux: S h = 4.36 Sh = 4.36 S h = 4.36

For the laminar entrance region, the Graetz-Leveque mass transfer equation applies: S h a v g = 1.62 ( R e ⋅ S c ⋅ D L ) 1 / 3 Sh_{avg} = 1.62 \left( Re \cdot Sc \cdot \frac{D}{L} \right)^{1/3} S h a vg ​ = 1.62 ( R e ⋅ S c ⋅ L D ​ ) 1/3

Turbulent Flow ( R e > 10 , 000 , 0.7 ≤ S c ≤ 160 Re > 10,000, 0.7 \le Sc \le 160 R e > 10 , 000 , 0.7 ≤ S c ≤ 160 ):

The Linton-Sherwood (or Gilliland) correlation relates pipe mass transfer to fluid properties: S h = 0.023 ⋅ R e 0.83 ⋅ S c 0.44 \mathbf{Sh = 0.023 \cdot Re^{0.83} \cdot Sc^{0.44}} Sh = 0.023 ⋅ R e 0.83 ⋅ S c 0.44

Alternatively, invoking the Chilton-Colburn analogy with the Blasius friction factor ( f = 0.079 R e − 0.25 f = 0.079 Re^{-0.25} f = 0.079 R e − 0.25 ): S h = 0.023 ⋅ R e 0.80 ⋅ S c 1 / 3 Sh = 0.023 \cdot Re^{0.80} \cdot Sc^{1/3} S h = 0.023 ⋅ R e 0.80 ⋅ S c 1/3

4. Flow Over a Flat Plate

For boundary layer flow over a smooth flat plate of length L L L :

Laminar Boundary Layer ( R e L < 5 × 10 5 Re_L < 5 \times 10^5 R e L ​ < 5 × 1 0 5 ): S h a v g = 0.664 ⋅ R e L 1 / 2 ⋅ S c 1 / 3 Sh_{avg} = 0.664 \cdot Re_L^{1/2} \cdot Sc^{1/3} S h a vg ​ = 0.664 ⋅ R e L 1/2 ​ ⋅ S c 1/3

Turbulent Boundary Layer ( R e L > 5 × 10 5 Re_L > 5 \times 10^5 R e L ​ > 5 × 1 0 5 ): S h a v g = 0.037 ⋅ R e L 0.80 ⋅ S c 1 / 3 Sh_{avg} = 0.037 \cdot Re_L^{0.80} \cdot Sc^{1/3} S h a vg ​ = 0.037 ⋅ R e L 0.80 ​ ⋅ S c 1/3

5. Flow Through Packed Beds (Wakao and Kaguei)

For fluid flowing through a packed bed of spheres of diameter d p d_p d p ​ : S h = 2.0 + 1.1 ⋅ R e p 0.60 ⋅ S c 1 / 3 \mathbf{Sh = 2.0 + 1.1 \cdot Re_p^{0.60} \cdot Sc^{1/3}} Sh = 2.0 + 1.1 ⋅ R e p 0.60 ​ ⋅ S c 1/3

Where R e p = ρ u s u p e r f i c i a l d p μ Re_p = \frac{\rho u_{superficial} d_p}{\mu} R e p ​ = μ ρ u s u p er f i c ia l ​ d p ​ ​ ( 3 ≤ R e p ≤ 10 , 000 3 \le Re_p \le 10,000 3 ≤ R e p ​ ≤ 10 , 000 ).

4. Summary Table of Dimensionless Groups and Analogies

Group Mathematical Definition Physical Meaning Heat Transfer Counterpart Typical Industrial Values

Sherwood ( S h Sh S h ) k c L D A B \frac{k_c L}{D_{AB}} D A B ​ k c ​ L ​ Total convective mass transfer rate Molecular diffusion rate \frac{\text{Total convective mass transfer rate}}{\text{Molecular diffusion rate}} Molecular diffusion rate Total convective mass transfer rate ​ Nusselt number ( N u = h L k Nu = \frac{h L}{k} N u = k h L ​ ) 2.0 2.0 2.0 to 5 , 000 5,000 5 , 000

Schmidt ( S c Sc S c ) μ ρ D A B = ν D A B \frac{\mu}{\rho D_{AB}} = \frac{\nu}{D_{AB}} ρ D A B ​ μ ​ = D A B ​ ν ​ Momentum diffusivity (kinematic viscosity) Mass diffusivity \frac{\text{Momentum diffusivity (kinematic viscosity)}}{\text{Mass diffusivity}} Mass diffusivity Momentum diffusivity (kinematic viscosity) ​ Prandtl number ( P r = ν α Pr = \frac{\nu}{\alpha} P r = α ν ​ ) Gases: 0.5 − 2.5 0.5 - 2.5 0.5 − 2.5 ; Liquids: 500 − 5 , 000 500 - 5,000 500 − 5 , 000

Peclet ( P e m Pe_m P e m ​ ) R e ⋅ S c = u L D A B Re \cdot Sc = \frac{u L}{D_{AB}} R e ⋅ S c = D A B ​ uL ​ Bulk convective advection rate Molecular diffusion rate \frac{\text{Bulk convective advection rate}}{\text{Molecular diffusion rate}} Molecular diffusion rate Bulk convective advection rate ​ Thermal Peclet ( P e h = R e ⋅ P r Pe_h = Re \cdot Pr P e h ​ = R e ⋅ P r ) 10 2 10^2 1 0 2 to 10 8 10^8 1 0 8

Lewis ( L e Le L e ) S c P r = α D A B \frac{Sc}{Pr} = \frac{\alpha}{D_{AB}} P r S c ​ = D A B ​ α ​ Thermal diffusivity Mass diffusivity \frac{\text{Thermal diffusivity}}{\text{Mass diffusivity}} Mass diffusivity Thermal diffusivity ​ Unity for air-water Air-water vapor: ≈ 1.0 \approx 1.0 ≈ 1.0 ; Liquids: 10 − 100 10 - 100 10 − 100

Stanton ( S t m St_m S t m ​ ) S h R e ⋅ S c = k c u \frac{Sh}{Re \cdot Sc} = \frac{k_c}{u} R e ⋅ S c S h ​ = u k c ​ ​ Actual mass transfer rate Convective transport capacity \frac{\text{Actual mass transfer rate}}{\text{Convective transport capacity}} Convective transport capacity Actual mass transfer rate ​ Thermal Stanton ( S t h = N u R e ⋅ P r St_h = \frac{Nu}{Re \cdot Pr} S t h ​ = R e ⋅ P r N u ​ ) 10 − 5 10^{-5} 1 0 − 5 to 10 − 2 10^{-2} 1 0 − 2

Chilton-Colburn ( j D j_D j D ​ ) S t m ⋅ S c 2 / 3 = S h R e ⋅ S c 1 / 3 St_m \cdot Sc^{2/3} = \frac{Sh}{Re \cdot Sc^{1/3}} S t m ​ ⋅ S c 2/3 = R e ⋅ S c 1/3 S h ​ Modified mass transfer friction factor ( j D = f / 2 j_D = f/2 j D ​ = f /2 ) Colburn factor ( j H = S t h ⋅ P r 2 / 3 j_H = St_h \cdot Pr^{2/3} j H ​ = S t h ​ ⋅ P r 2/3 ) 10 − 4 10^{-4} 1 0 − 4 to 10 − 2 10^{-2} 1 0 − 2

  • 5. Comprehensive Worked Numerical Example: Sublimation from a Suspended Sphere
  • Problem Statement

To calibrate an aerodynamic test section, a smooth spherical pellet of pure naphthalene ( C 10 H 8 \text{C}_{10}\text{H}_8 C 10 ​ H 8 ​ , M A = 128.17 g/mol M_A = 128.17\text{ g/mol} M A ​ = 128.17 g/mol ) having a diameter of d p = 25.0 mm = 0.0250 m d_p = 25.0\text{ mm} = 0.0250\text{ m} d p ​ = 25.0 mm = 0.0250 m is suspended in a dry air stream inside a wind tunnel.

Operating Conditions:

Air temperature: T = 300.0 K T = 300.0\text{ K} T = 300.0 K ( 26.85 ∘ C 26.85^\circ\text{C} 26.8 5 ∘ C ).

Absolute tunnel pressure: P = 1.01325 bar = 101 , 325 Pa P = 1.01325\text{ bar} = 101,325\text{ Pa} P = 1.01325 bar = 101 , 325 Pa .

Free-stream air velocity: u = 4.50 m/s u = 4.50\text{ m/s} u = 4.50 m/s .

Physical Properties at 300.0 K 300.0\text{ K} 300.0 K :

Air density: ρ = 1.177 kg/m 3 \rho = 1.177\text{ kg/m}^3 ρ = 1.177 kg/m 3 .

Air dynamic viscosity: μ = 1.85 × 10 − 5 Pa ⋅ s = 1.85 × 10 − 5 kg/(m ⋅ s) \mu = 1.85 \times 10^{-5}\text{ Pa}\cdot\text{s} = 1.85 \times 10^{-5}\text{ kg/(m}\cdot\text{s)} μ = 1.85 × 1 0 − 5 Pa ⋅ s = 1.85 × 1 0 − 5 kg/(m ⋅ s) .

Air kinematic viscosity: ν = μ / ρ = 1.5718 × 10 − 5 m 2 / s \nu = \mu / \rho = 1.5718 \times 10^{-5}\text{ m}^2/\text{s} ν = μ / ρ = 1.5718 × 1 0 − 5 m 2 / s .

Binary diffusivity of naphthalene in air: D A B = 6.11 × 10 − 6 m 2 / s D_{AB} = 6.11 \times 10^{-6}\text{ m}^2/\text{s} D A B ​ = 6.11 × 1 0 − 6 m 2 / s .

Vapor pressure of solid naphthalene: P A ∗ = 11.0 Pa P_A^* = 11.0\text{ Pa} P A ∗ ​ = 11.0 Pa .

Universal gas constant: R = 8.31446 J/(mol ⋅ K) R = 8.31446\text{ J/(mol}\cdot\text{K)} R = 8.31446 J/(mol ⋅ K) .

Calculate:

The particle Reynolds number ( R e p Re_p R e p ​ ) and Schmidt number ( S c Sc S c ).

The mass transfer Peclet number ( P e m Pe_m P e m ​ ).

The Sherwood number ( S h Sh S h ) using the Froessling correlation.

The convective mass transfer coefficient ( k c k_c k c ​ ) in m/s \text{m/s} m/s .

The Chilton-Colburn j D j_D j D ​ factor.

The molar sublimation flux ( N A N_A N A ​ ) in mol/(m 2 ⋅ s) \text{mol/(m}^2\cdot\text{s)} mol/(m 2 ⋅ s) and total mass sublimation rate ( m ˙ A \dot{m}_A m ˙ A ​ ) in mg/hr \text{mg/hr} mg/hr from the sphere.

Step 1: Dimensionless Group Evaluation ( R e p Re_p R e p ​ and S c Sc S c )

Particle Reynolds number: R e p = ρ u d p μ = ( 1.177 kg/m 3 ) × ( 4.50 m/s ) × ( 0.0250 m ) 1.85 × 10 − 5 Pa ⋅ s Re_p = \frac{\rho u d_p}{\mu} = \frac{(1.177\text{ kg/m}^3) \times (4.50\text{ m/s}) \times (0.0250\text{ m})}{1.85 \times 10^{-5}\text{ Pa}\cdot\text{s}} R e p ​ = μ ρ u d p ​ ​ = 1.85 × 1 0 − 5 Pa ⋅ s ( 1.177 kg/m 3 ) × ( 4.50 m/s ) × ( 0.0250 m ) ​ R e p = 0.1324125 1.85 × 10 − 5 = 7 , 157.4 ≈ 7 , 157 Re_p = \frac{0.1324125}{1.85 \times 10^{-5}} = \mathbf{7,157.4} \approx \mathbf{7,157} R e p ​ = 1.85 × 1 0 − 5 0.1324125 ​ = 7 , 157.4 ≈ 7 , 157

Schmidt number: S c = ν D A B = 1.5718 × 10 − 5 m 2 / s 6.11 × 10 − 6 m 2 / s = 2.5725 ≈ 2.573 Sc = \frac{\nu}{D_{AB}} = \frac{1.5718 \times 10^{-5}\text{ m}^2/\text{s}}{6.11 \times 10^{-6}\text{ m}^2/\text{s}} = \mathbf{2.5725} \approx \mathbf{2.573} S c = D A B ​ ν ​ = 6.11 × 1 0 − 6 m 2 / s 1.5718 × 1 0 − 5 m 2 / s ​ = 2.5725 ≈ 2.573

Step 2: Mass Transfer Peclet Number ( P e m Pe_m P e m ​ ) P e m = R e p ⋅ S c = 7 , 157.4 × 2.5725 = 18 , 412 Pe_m = Re_p \cdot Sc = 7,157.4 \times 2.5725 = \mathbf{18,412} P e m ​ = R e p ​ ⋅ S c = 7 , 157.4 × 2.5725 = 18 , 412

Convective advection dominates molecular diffusion by more than four orders of magnitude.

Step 3: Sherwood Number Determination

Applying the Froessling correlation for forced convection past a sphere: S h = 2.0 + 0.60 ⋅ R e p 1 / 2 ⋅ S c 1 / 3 Sh = 2.0 + 0.60 \cdot Re_p^{1/2} \cdot Sc^{1/3} S h = 2.0 + 0.60 ⋅ R e p 1/2 ​ ⋅ S c 1/3

Evaluate components:

  • R e p 1 / 2 = 7 , 157.4 = 84.601 Re_p^{1/2} = \sqrt{7,157.4} = 84.601 R e p 1/2 ​ = 7 , 157.4 ​ = 84.601
  • S c 1 / 3 = ( 2.5725 ) 1 / 3 = 1.3702 Sc^{1/3} = (2.5725)^{1/3} = 1.3702 S c 1/3 = ( 2.5725 ) 1/3 = 1.3702

Substitute into correlation: S h = 2.0 + 0.60 × 84.601 × 1.3702 = 2.0 + 0.60 × 115.920 Sh = 2.0 + 0.60 \times 84.601 \times 1.3702 = 2.0 + 0.60 \times 115.920 S h = 2.0 + 0.60 × 84.601 × 1.3702 = 2.0 + 0.60 × 115.920 S h = 2.0 + 69.552 = 71.552 ≈ 71.55 Sh = 2.0 + 69.552 = \mathbf{71.552} \approx \mathbf{71.55} S h = 2.0 + 69.552 = 71.552 ≈ 71.55

(Note: Stagnant conduction represents 2.0 / 71.55 = 2.8 % 2.0 / 71.55 = 2.8\% 2.0/71.55 = 2.8% of total transfer, while forced convection contributes 97.2 % 97.2\% 97.2% ).

Step 4: Convective Mass Transfer Coefficient ( k c k_c k c ​ ) S h = k c d p D A B ⟹ k c = S h ⋅ D A B d p Sh = \frac{k_c d_p}{D_{AB}} \implies k_c = \frac{Sh \cdot D_{AB}}{d_p} S h = D A B ​ k c ​ d p ​ ​ ⟹ k c ​ = d p ​ S h ⋅ D A B ​ ​ k c = 71.552 × ( 6.11 × 10 − 6 m 2 / s ) 0.0250 m = 4.3718 × 10 − 4 0.0250 = 0.017487 m/s = 1.749 × 10 − 2 m/s k_c = \frac{71.552 \times (6.11 \times 10^{-6}\text{ m}^2/\text{s})}{0.0250\text{ m}} = \frac{4.3718 \times 10^{-4}}{0.0250} = \mathbf{0.017487\text{ m/s}} = \mathbf{1.749 \times 10^{-2}\text{ m/s}} k c ​ = 0.0250 m 71.552 × ( 6.11 × 1 0 − 6 m 2 / s ) ​ = 0.0250 4.3718 × 1 0 − 4 ​ = 0.017487 m/s = 1.749 × 1 0 − 2 m/s

Step 5: Chilton-Colburn j D j_D j D ​ Factor

Mass transfer Stanton number: S t m = k c u = 0.017487 m/s 4.50 m/s = 3.8860 × 10 − 3 St_m = \frac{k_c}{u} = \frac{0.017487\text{ m/s}}{4.50\text{ m/s}} = 3.8860 \times 10^{-3} S t m ​ = u k c ​ ​ = 4.50 m/s 0.017487 m/s ​ = 3.8860 × 1 0 − 3

Evaluate S c 2 / 3 Sc^{2/3} S c 2/3 : S c 2 / 3 = ( 2.5725 ) 2 / 3 = 1.8774 Sc^{2/3} = (2.5725)^{2/3} = 1.8774 S c 2/3 = ( 2.5725 ) 2/3 = 1.8774

Calculate j D j_D j D ​ : j D = S t m ⋅ S c 2 / 3 = ( 3.8860 × 10 − 3 ) × 1.8774 = 7.296 × 10 − 3 ≈ 7.30 × 10 − 3 j_D = St_m \cdot Sc^{2/3} = (3.8860 \times 10^{-3}) \times 1.8774 = \mathbf{7.296 \times 10^{-3}} \approx \mathbf{7.30 \times 10^{-3}} j D ​ = S t m ​ ⋅ S c 2/3 = ( 3.8860 × 1 0 − 3 ) × 1.8774 = 7.296 × 1 0 − 3 ≈ 7.30 × 1 0 − 3

Step 6: Sublimation Flux and Mass Sublimation Rate

Surface vapor concentration of naphthalene: C A s = P A ∗ R T = 11.0 Pa ( 8.31446 J/(mol ⋅ K) ) × ( 300.0 K ) = 11.0 2 , 494.34 = 4.40998 × 10 − 3 mol/m 3 C_{As} = \frac{P_A^*}{R T} = \frac{11.0\text{ Pa}}{(8.31446\text{ J/(mol}\cdot\text{K)}) \times (300.0\text{ K})} = \frac{11.0}{2,494.34} = \mathbf{4.40998 \times 10^{-3}\text{ mol/m}^3} C A s ​ = RT P A ∗ ​ ​ = ( 8.31446 J/(mol ⋅ K) ) × ( 300.0 K ) 11.0 Pa ​ = 2 , 494.34 11.0 ​ = 4.40998 × 1 0 − 3 mol/m 3

Since bulk air contains zero naphthalene ( C A ∞ = 0 C_{A\infty} = 0 C A ∞ ​ = 0 ), the driving force is Δ C A = C A s \Delta C_A = C_{As} Δ C A ​ = C A s ​ : N A = k c ⋅ C A s = ( 0.017487 m/s ) × ( 4.40998 × 10 − 3 mol/m 3 ) = 7.7117 × 10 − 5 mol/(m 2 ⋅ s) N_A = k_c \cdot C_{As} = (0.017487\text{ m/s}) \times (4.40998 \times 10^{-3}\text{ mol/m}^3) = \mathbf{7.7117 \times 10^{-5}\text{ mol/(m}^2\cdot\text{s)}} N A ​ = k c ​ ⋅ C A s ​ = ( 0.017487 m/s ) × ( 4.40998 × 1 0 − 3 mol/m 3 ) = 7.7117 × 1 0 − 5 mol/(m 2 ⋅ s)

Total outer surface area of the sphere: A s = π d p 2 = π × ( 0.0250 m ) 2 = 1.9635 × 10 − 3 m 2 A_s = \pi d_p^2 = \pi \times (0.0250\text{ m})^2 = \mathbf{1.9635 \times 10^{-3}\text{ m}^2} A s ​ = π d p 2 ​ = π × ( 0.0250 m ) 2 = 1.9635 × 1 0 − 3 m 2

Molar sublimation rate: n ˙ A = N A ⋅ A s = ( 7.7117 × 10 − 5 mol/(m 2 ⋅ s) ) × ( 1.9635 × 10 − 3 m 2 ) = 1.5142 × 10 − 7 mol/s \dot{n}_A = N_A \cdot A_s = (7.7117 \times 10^{-5}\text{ mol/(m}^2\cdot\text{s)}) \times (1.9635 \times 10^{-3}\text{ m}^2) = 1.5142 \times 10^{-7}\text{ mol/s} n ˙ A ​ = N A ​ ⋅ A s ​ = ( 7.7117 × 1 0 − 5 mol/(m 2 ⋅ s) ) × ( 1.9635 × 1 0 − 3 m 2 ) = 1.5142 × 1 0 − 7 mol/s

Mass sublimation rate: m ˙ A = n ˙ A ⋅ M A = ( 1.5142 × 10 − 7 mol/s ) × ( 128.17 g/mol ) = 1.9407 × 10 − 5 g/s = 1.9407 × 10 − 2 mg/s \dot{m}_A = \dot{n}_A \cdot M_A = (1.5142 \times 10^{-7}\text{ mol/s}) \times (128.17\text{ g/mol}) = 1.9407 \times 10^{-5}\text{ g/s} = 1.9407 \times 10^{-2}\text{ mg/s} m ˙ A ​ = n ˙ A ​ ⋅ M A ​ = ( 1.5142 × 1 0 − 7 mol/s ) × ( 128.17 g/mol ) = 1.9407 × 1 0 − 5 g/s = 1.9407 × 1 0 − 2 mg/s

Converting to hourly loss: m ˙ A = 1.9407 × 10 − 2 mg/s × 3 , 600 s/hr = 69.87 mg/hr ≈ 69.9 mg/hr \dot{m}_A = 1.9407 \times 10^{-2}\text{ mg/s} \times 3,600\text{ s/hr} = \mathbf{69.87\text{ mg/hr}} \approx \mathbf{69.9\text{ mg/hr}} m ˙ A ​ = 1.9407 × 1 0 − 2 mg/s × 3 , 600 s/hr = 69.87 mg/hr ≈ 69.9 mg/hr

  • 6. Critical NCEES PE Exam Traps & Pitfalls
  • Trap 1: Confusing Fanning and Darcy Friction Factors in the Chilton-Colburn Analogy

The Chilton-Colburn relationship is defined strictly as j D = f / 2 j_D = f / 2 j D ​ = f /2 , where f f f is the Fanning friction factor (found on the PE Handbook mass transfer page and in chemical engineering fluid flow tables). In mechanical civil hydraulics tables, the Darcy friction factor is f D = 4 f f_D = 4f f D ​ = 4 f . If you substitute f D f_D f D ​ directly into j D = f D / 2 j_D = f_D / 2 j D ​ = f D ​ /2 , you will calculate a mass transfer coefficient that is 400 % 400\% 400% too large ! Remember: j D = f Fanning / 2 = f Darcy / 8 j_D = f_{\text{Fanning}} / 2 = f_{\text{Darcy}} / 8 j D ​ = f Fanning ​ /2 = f Darcy ​ /8 .

Trap 2: Forgetting the Asymptotic Lower Limit S h = 2.0 Sh = 2.0 S h = 2.0 for Spheres and Droplets

In spray scrubbers, fluid bed driers, or evaporative coolers, when relative droplet velocity approaches zero ( u → 0 , R e p → 0 u \to 0, Re_p \to 0 u → 0 , R e p ​ → 0 ), the convective contribution vanishes, but S h Sh S h does not equal zero ! It approaches S h = 2.0 Sh = 2.0 S h = 2.0 asymptotically due to 3D spherical molecular diffusion. Assuming k c → 0 k_c \to 0 k c ​ → 0 when velocity stops will cause you to grossly miscalculate droplet drying or dissolution times.

Trap 3: Applying Gas-Phase Correlations Directly to Liquid-Phase Flows

Gas-phase mass transfer correlations often assume S c ≈ 1 Sc \approx 1 S c ≈ 1 . If an engineer uses a gas-phase correlation for water flow ( S c ≈ 1 , 000 Sc \approx 1,000 S c ≈ 1 , 000 ), the resulting coefficient will be completely erroneous. In liquids, because S c Sc S c is so large, the mass transfer resistance is confined to an extremely thin sublayer ( δ c ≈ 0.1 δ u \delta_c \approx 0.1 \delta_u δ c ​ ≈ 0.1 δ u ​ ), requiring correlations with proper S c 1 / 3 Sc^{1/3} S c 1/3 or S c 0.44 Sc^{0.44} S c 0.44 dampening terms.