Study guide
1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems)
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems)
Key Takeaways Explain This Topic AI
Atomic species balances require no generation or consumption terms because chemical reactions conserve individual nuclear atoms (sum Atoms In = sum Atoms Out).
The extent of reaction (xi) formulation decouples stoichiometry from stream accounting via n_{i,out} = n_{i,in} + sum (nu_{ir} * xi_r), creating linear systems for multi-reaction networks.
Percent excess reactant is strictly defined relative to the stoichiometric amount required to consume the limiting reactant fed to completion: % Excess = [(n_fed - n_stoich) / n_stoich] * 100%.
Fractional conversion quantifies reactant disappearance [X_A = (n_{A,in} - n_{A,out}) / n_{A,in}], whereas selectivity defines the molar ratio of desired product formed relative to competitive byproduct formed.
In combustion systems, theoretical oxygen assumes 100% conversion of fuel carbon to CO2, hydrogen to H2O, and sulfur to SO2; Orsat gas analysis reports flue gas composition on a moisture-free dry basis.
Last updated: September 2026
1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems)
Material balance calculations under steady-state conditions represent the primary test of a chemical engineer's core competency on the NCEES PE Chemical Exam . While non-reactive systems require only physical accounting of conserved mass, reactive systems require simultaneous reconciliation of chemical stoichiometry, reaction equilibrium, conversion kinetics, and selectivity. The PE exam tests your ability to choose the most computationally efficient balancing technique—molecular species balances, atomic species balances, or extents of reaction—under tight exam timing constraints.
The Steady-State Mass Conservation Equation
For any continuous chemical process operating at steady state, the rate of accumulation of total mass and individual atomic elements within the control volume is identically zero: ∑ m ˙ in = ∑ m ˙ out \sum \dot{m}_{\text{in}} = \sum \dot{m}_{\text{out}} ∑ m ˙ in = ∑ m ˙ out
For a specific chemical species i i i , the molar balance accounts for chemical generation and consumption: n ˙ i , in + R ˙ i , gen = n ˙ i , out + R ˙ i , con \dot{n}_{i, \text{in}} + \dot{R}_{i, \text{gen}} = \dot{n}_{i, \text{out}} + \dot{R}_{i, \text{con}} n ˙ i , in + R ˙ i , gen = n ˙ i , out + R ˙ i , con
Where n ˙ i \dot{n}_i n ˙ i is the molar flow rate (lbmol/h or kmol/h), and R ˙ i , gen \dot{R}_{i, \text{gen}} R ˙ i , gen and R ˙ i , con \dot{R}_{i, \text{con}} R ˙ i , con represent the molar rates of generation and consumption through chemical reaction.
Three Balancing Methodologies for Reactive Systems
Depending on the complexity of the reaction network and the nature of the given data, chemical engineers employ one of three distinct balancing methodologies:
1. Molecular Species Balances
Formulation : Formulate explicit input-output-generation-consumption balances for each molecular compound using reaction stoichiometry.
Governing Equation : n ˙ i , out = n ˙ i , in + ∑ r = 1 R ν i r ξ r \dot{n}_{i, \text{out}} = \dot{n}_{i, \text{in}} + \sum_{r=1}^R \nu_{ir} \xi_r n ˙ i , out = n ˙ i , in + ∑ r = 1 R ν i r ξ r
Best Used When : The flowsheet involves only a single reaction or simple non-reversible parallel reactions with clearly specified fractional conversions.
2. Atomic (Elemental) Balances
Formulation : Perform balances on individual atomic nuclei (Carbon, Hydrogen, Oxygen, Nitrogen, etc.). Because chemical reactions only rearrange atomic bonds without altering nuclear identity, generation and consumption terms are identically zero : ∑ all input streams j n ˙ j a j i = ∑ all output streams k n ˙ k a k i \sum_{\text{all input streams } j} \dot{n}_j a_{ji} = \sum_{\text{all output streams } k} \dot{n}_k a_{ki} all input streams j ∑ n ˙ j a ji = all output streams k ∑ n ˙ k a ki
Where a j i a_{ji} a ji is the number of atoms of element i i i in molecule j j j .
Best Used When : Reaction mechanisms are complex, unknown, or involve multiple simultaneous cracking, combustion, gasification, or reforming steps (e.g., coal gasification, biomass pyrolysis, steam cracking).
PE Rule : When using atomic balances, do not write molecular balances or extent-of-reaction equations; doing so produces mathematically dependent equations.
3. Extent of Reaction ( ξ \xi ξ ) Formulation
Formulation : For a reaction network with R R R independent chemical reactions, define an extent of reaction ξ r \xi_r ξ r for each reaction r r r : n ˙ i , out = n ˙ i , in + ∑ r = 1 R ν i r ξ r \dot{n}_{i, \text{out}} = \dot{n}_{i, \text{in}} + \sum_{r=1}^R \nu_{ir} \xi_r n ˙ i , out = n ˙ i , in + r = 1 ∑ R ν i r ξ r
Where ν i r \nu_{ir} ν i r is the stoichiometric coefficient of species i i i in reaction r r r (positive for products, negative for reactants, zero for inerts).
Best Used When : Multi-reaction networks with series and parallel pathways where yield, selectivity, or equilibrium expressions are specified in terms of reaction progress.
Summary Table: Reactive Material Balance Methods
Method Primary Unknowns Balance Equations Treatment of Reactions Primary Advantage on PE Exam
Molecular Balances Exit molar flows n ˙ i \dot{n}_i n ˙ i C C C molecular species balances Generation/consumption terms calculated via stoichiometry Intuitive for single reactions with known conversions.
Atomic Balances Exit stream flows & fractions Number of independent elements Completely ignored; no ξ \xi ξ or generation terms Fastest method when reaction paths are complex or incomplete.
Extent of Reaction Extents ξ 1 , … , ξ R \xi_1, \dots, \xi_R ξ 1 , … , ξ R and exit flows n ˙ i = n ˙ i , 0 + ∑ ν i r ξ r \dot{n}_i = \dot{n}_{i,0} + \sum \nu_{ir} \xi_r n ˙ i = n ˙ i , 0 + ∑ ν i r ξ r Embedded systematically through stoichiometric matrix Systematic linear algebra; easily handles parallel/series reactions.
- Stoichiometric Definitions & Critical PE Exam Traps
- Limiting and Excess Reactants
Limiting Reactant : The reactant present in the smallest stoichiometric proportion. If the reaction proceeded to 100% completion, the limiting reactant would be completely consumed first.
Theoretical (Stoichiometric) Requirement : The molar quantity of excess reactant required to react completely with all limiting reactant fed to the reactor .
Percent Excess : % Excess = ( n ˙ excess, fed − n ˙ excess, stoichiometric n ˙ excess, stoichiometric ) × 100 % \%\text{ Excess} = \left( \frac{\dot{n}_{\text{excess, fed}} - \dot{n}_{\text{excess, stoichiometric}}}{\dot{n}_{\text{excess, stoichiometric}}} \right) \times 100\% % Excess = ( n ˙ excess, stoichiometric n ˙ excess, fed − n ˙ excess, stoichiometric ) × 100%
Warning
CRITICAL PE EXAM TRAP: The theoretical stoichiometric requirement n ˙ excess, stoichiometric \dot{n}_{\text{excess, stoichiometric}} n ˙ excess, stoichiometric is calculated based on 100% conversion of the limiting reactant fed , regardless of the actual fractional conversion achieved in the reactor!
A frequent exam trap provides a conversion of 60 % 60\% 60% and tempts the candidate to calculate excess air based on the 60 % 60\% 60% fuel actually burned. This will invariably match an incorrect distractor.
Fractional Conversion, Yield, and Selectivity
Fractional Conversion ( X A X_A X A ) : The fraction of reactant A A A fed that is consumed by all reactions: X A = n ˙ A , in − n ˙ A , out n ˙ A , in X_A = \frac{\dot{n}_{A, \text{in}} - \dot{n}_{A, \text{out}}}{\dot{n}_{A, \text{in}}} X A = n ˙ A , in n ˙ A , in − n ˙ A , out
Fractional Yield ( Y P Y_P Y P ) : The moles of desired product P P P formed divided by the moles of product that would have formed if all of the limiting reactant fed had reacted exclusively to produce P P P : Y P = n ˙ P , out − n ˙ P , in n ˙ A , in ( ν P ∣ ν A ∣ ) Y_P = \frac{\dot{n}_{P, \text{out}} - \dot{n}_{P, \text{in}}}{\dot{n}_{A, \text{in}} \left( \frac{\nu_P}{|\nu_A|} \right)} Y P = n ˙ A , in ( ∣ ν A ∣ ν P ) n ˙ P , out − n ˙ P , in
Selectivity ( S P / U S_{P/U} S P / U ) : The molar ratio of desired product P P P formed relative to undesired byproduct U U U formed: S P / U = n ˙ P , formed n ˙ U , formed = n ˙ P , out − n ˙ P , in n ˙ U , out − n ˙ U , in S_{P/U} = \frac{\dot{n}_{P, \text{formed}}}{\dot{n}_{U, \text{formed}}} = \frac{\dot{n}_{P, \text{out}} - \dot{n}_{P, \text{in}}}{\dot{n}_{U, \text{out}} - \dot{n}_{U, \text{in}}} S P / U = n ˙ U , formed n ˙ P , formed = n ˙ U , out − n ˙ U , in n ˙ P , out − n ˙ P , in
Combustion Calculations & Flue Gas Accounting
Combustion systems feature heavily in the PE Chemical exam thermal-fluids and kinetics domains:
Theoretical Oxygen (Air) : The exact moles of O 2 \text{O}_2 O 2 needed to oxidize all fuel carbon to CO 2 \text{CO}_2 CO 2 , all hydrogen to H 2 O \text{H}_2\text{O} H 2 O , all sulfur to SO 2 \text{SO}_2 SO 2 , and all nitrogen to N 2 \text{N}_2 N 2 (unreacted).
Standard Air Composition : Standard dry atmospheric air consists of 21.0 mol% O 2 21.0\text{ mol\% }\text{O}_2 21.0 mol% O 2 and 79.0 mol% N 2 79.0\text{ mol\% }\text{N}_2 79.0 mol% N 2 , giving the fundamental stoichiometric ratio: Moles N 2 Moles O 2 = 79.0 21.0 = 3.762 \frac{\text{Moles } \text{N}_2}{\text{Moles } \text{O}_2} = \frac{79.0}{21.0} = 3.762 Moles O 2 Moles N 2 = 21.0 79.0 = 3.762
Wet Basis vs. Orsat (Dry Basis) Analysis :
Wet Basis : Includes water vapor in the total molar flue gas count.
Orsat (Dry Basis) : Measures combustion flue gas after condensing and removing all water vapor. y i , wet = y i , dry ( 1 − y H 2 O , wet ) y_{i, \text{wet}} = y_{i, \text{dry}} \left( 1 - y_{\text{H}_2\text{O}, \text{wet}} \right) y i , wet = y i , dry ( 1 − y H 2 O , wet ) y i , dry = y i , wet 1 − y H 2 O , wet y_{i, \text{dry}} = \frac{y_{i, \text{wet}}}{1 - y_{\text{H}_2\text{O}, \text{wet}}} y i , dry = 1 − y H 2 O , wet y i , wet
- Comprehensive Worked Numerical Example: Propane Dehydrogenation & Cracking
- Problem Statement
A chemical reactor is fed 1 , 000 lbmol/h 1,000\text{ lbmol/h} 1 , 000 lbmol/h of a hydrocarbon feed gas consisting of 90.0 mol% 90.0\text{ mol\%} 90.0 mol% propane ( C 3 H 8 \text{C}_3\text{H}_8 C 3 H 8 ) and 10.0 mol% 10.0\text{ mol\%} 10.0 mol% nitrogen ( N 2 \text{N}_2 N 2 , inert). Inside the catalytic reactor, two simultaneous gas-phase reactions occur:
Dehydrogenation to Propylene (Desired) : C 3 H 8 ⟶ C 3 H 6 + H 2 ( Reaction 1, Extent ξ 1 ) \text{C}_3\text{H}_8 \longrightarrow \text{C}_3\text{H}_6 + \text{H}_2 \quad (\text{Reaction 1, Extent } \xi_1) C 3 H 8 ⟶ C 3 H 6 + H 2 ( Reaction 1, Extent ξ 1 )
Cracking to Ethylene and Methane (Undesired) : C 3 H 8 ⟶ C 2 H 4 + CH 4 ( Reaction 2, Extent ξ 2 ) \text{C}_3\text{H}_8 \longrightarrow \text{C}_2\text{H}_4 + \text{CH}_4 \quad (\text{Reaction 2, Extent } \xi_2) C 3 H 8 ⟶ C 2 H 4 + CH 4 ( Reaction 2, Extent ξ 2 )
Process Specifications:
The fractional conversion of propane is X = 0.800 X = 0.800 X = 0.800 ( 80.0 % 80.0\% 80.0% ).
The selectivity of propylene relative to ethylene in the reactor product is S = 8.00 lbmol C 3 H 6 / lbmol C 2 H 4 S = 8.00\text{ lbmol }\text{C}_3\text{H}_6 / \text{lbmol }\text{C}_2\text{H}_4 S = 8.00 lbmol C 3 H 6 / lbmol C 2 H 4 .
Calculate:
The extents of reaction ξ 1 \xi_1 ξ 1 and ξ 2 \xi_2 ξ 2 (lbmol/h).
The complete component molar flow rates and total molar flow rate of the reactor effluent.
Verify the solution using independent atomic balances for Carbon and Hydrogen.
Calculate the fractional yield of propylene based on propane fed.
Step 1: Feed Rates & Extents of Reaction Formulation
Feed stream molar flow rates:
Propane fed: n ˙ C 3 H 8 , 0 = 1 , 000 × 0.900 = 900.0 lbmol/h \dot{n}_{\text{C}_3\text{H}_8, 0} = 1,000 \times 0.900 = 900.0\text{ lbmol/h} n ˙ C 3 H 8 , 0 = 1 , 000 × 0.900 = 900.0 lbmol/h
Nitrogen fed: n ˙ N 2 , 0 = 1 , 000 × 0.100 = 100.0 lbmol/h \dot{n}_{\text{N}_2, 0} = 1,000 \times 0.100 = 100.0\text{ lbmol/h} n ˙ N 2 , 0 = 1 , 000 × 0.100 = 100.0 lbmol/h
From the conversion specification ( X = 0.800 X = 0.800 X = 0.800 ): Propane consumed = n ˙ C 3 H 8 , 0 × X = 900.0 × 0.800 = 720.0 lbmol/h \text{Propane consumed} = \dot{n}_{\text{C}_3\text{H}_8, 0} \times X = 900.0 \times 0.800 = 720.0\text{ lbmol/h} Propane consumed = n ˙ C 3 H 8 , 0 × X = 900.0 × 0.800 = 720.0 lbmol/h Propane exiting = 900.0 − 720.0 = 180.0 lbmol/h \text{Propane exiting} = 900.0 - 720.0 = 180.0\text{ lbmol/h} Propane exiting = 900.0 − 720.0 = 180.0 lbmol/h
Both reactions consume propane with stoichiometric coefficient ν = − 1 \nu = -1 ν = − 1 : Total propane consumed = ξ 1 + ξ 2 = 720.0 lbmol/h \text{Total propane consumed} = \xi_1 + \xi_2 = 720.0\text{ lbmol/h} Total propane consumed = ξ 1 + ξ 2 = 720.0 lbmol/h
From reaction stoichiometry, propylene produced is n ˙ C 3 H 6 = ξ 1 \dot{n}_{\text{C}_3\text{H}_6} = \xi_1 n ˙ C 3 H 6 = ξ 1 , and ethylene produced is n ˙ C 2 H 4 = ξ 2 \dot{n}_{\text{C}_2\text{H}_4} = \xi_2 n ˙ C 2 H 4 = ξ 2 . The selectivity specification is: S = n ˙ C 3 H 6 n ˙ C 2 H 4 = ξ 1 ξ 2 = 8.00 ⟹ ξ 1 = 8.00 ξ 2 S = \frac{\dot{n}_{\text{C}_3\text{H}_6}}{\dot{n}_{\text{C}_2\text{H}_4}} = \frac{\xi_1}{\xi_2} = 8.00 \implies \xi_1 = 8.00 \xi_2 S = n ˙ C 2 H 4 n ˙ C 3 H 6 = ξ 2 ξ 1 = 8.00 ⟹ ξ 1 = 8.00 ξ 2
Substitute into the propane consumption equation: 8.00 ξ 2 + ξ 2 = 9.00 ξ 2 = 720.0 lbmol/h 8.00 \xi_2 + \xi_2 = 9.00 \xi_2 = 720.0\text{ lbmol/h} 8.00 ξ 2 + ξ 2 = 9.00 ξ 2 = 720.0 lbmol/h ξ 2 = 720.0 9.00 = 80.0 lbmol/h \xi_2 = \frac{720.0}{9.00} = \mathbf{80.0\text{ lbmol/h}} ξ 2 = 9.00 720.0 = 80.0 lbmol/h ξ 1 = 8.00 × 80.0 = 640.0 lbmol/h \xi_1 = 8.00 \times 80.0 = \mathbf{640.0\text{ lbmol/h}} ξ 1 = 8.00 × 80.0 = 640.0 lbmol/h
Step 2: Component Molar Flows in Reactor Effluent
Apply the extent of reaction equation n ˙ i = n ˙ i , 0 + ∑ ν i r ξ r \dot{n}_{i} = \dot{n}_{i, 0} + \sum \nu_{ir} \xi_r n ˙ i = n ˙ i , 0 + ∑ ν i r ξ r for each species:
Propane ( C 3 H 8 \text{C}_3\text{H}_8 C 3 H 8 ) : 900.0 − ξ 1 − ξ 2 = 900.0 − 640.0 − 80.0 = 180.0 lbmol/h 900.0 - \xi_1 - \xi_2 = 900.0 - 640.0 - 80.0 = \mathbf{180.0\text{ lbmol/h}} 900.0 − ξ 1 − ξ 2 = 900.0 − 640.0 − 80.0 = 180.0 lbmol/h
Propylene ( C 3 H 6 \text{C}_3\text{H}_6 C 3 H 6 ) : 0 + ξ 1 = 640.0 lbmol/h 0 + \xi_1 = \mathbf{640.0\text{ lbmol/h}} 0 + ξ 1 = 640.0 lbmol/h
Hydrogen ( H 2 \text{H}_2 H 2 ) : 0 + ξ 1 = 640.0 lbmol/h 0 + \xi_1 = \mathbf{640.0\text{ lbmol/h}} 0 + ξ 1 = 640.0 lbmol/h
Ethylene ( C 2 H 4 \text{C}_2\text{H}_4 C 2 H 4 ) : 0 + ξ 2 = 80.0 lbmol/h 0 + \xi_2 = \mathbf{80.0\text{ lbmol/h}} 0 + ξ 2 = 80.0 lbmol/h
Methane ( CH 4 \text{CH}_4 CH 4 ) : 0 + ξ 2 = 80.0 lbmol/h 0 + \xi_2 = \mathbf{80.0\text{ lbmol/h}} 0 + ξ 2 = 80.0 lbmol/h
Nitrogen ( N 2 \text{N}_2 N 2 , inert) : 100.0 + 0 = 100.0 lbmol/h 100.0 + 0 = \mathbf{100.0\text{ lbmol/h}} 100.0 + 0 = 100.0 lbmol/h
Total effluent molar flow rate: n ˙ total = 180.0 + 640.0 + 640.0 + 80.0 + 80.0 + 100.0 = 1 , 720.0 lbmol/h \dot{n}_{\text{total}} = 180.0 + 640.0 + 640.0 + 80.0 + 80.0 + 100.0 = \mathbf{1,720.0\text{ lbmol/h}} n ˙ total = 180.0 + 640.0 + 640.0 + 80.0 + 80.0 + 100.0 = 1 , 720.0 lbmol/h
(Notice that the total moles increased from 1 , 000 1,000 1 , 000 to 1 , 720 lbmol/h 1,720\text{ lbmol/h} 1 , 720 lbmol/h because each reaction produces 2 moles of product from 1 mole of reactant: Δ n = ξ 1 + ξ 2 = 720 lbmol/h \Delta n = \xi_1 + \xi_2 = 720\text{ lbmol/h} Δ n = ξ 1 + ξ 2 = 720 lbmol/h .)
Effluent Composition Table
Component Effluent Flow (lbmol/h) Mole Fraction ( y i y_i y i ) Mol %
Propane ( C 3 H 8 \text{C}_3\text{H}_8 C 3 H 8 ) 180.0 180.0 / 1720.0 = 0.1047 180.0 / 1720.0 = 0.1047 180.0/1720.0 = 0.1047 10.47%
Propylene ( C 3 H 6 \text{C}_3\text{H}_6 C 3 H 6 ) 640.0 640.0 / 1720.0 = 0.3721 640.0 / 1720.0 = 0.3721 640.0/1720.0 = 0.3721 37.21%
Hydrogen ( H 2 \text{H}_2 H 2 ) 640.0 640.0 / 1720.0 = 0.3721 640.0 / 1720.0 = 0.3721 640.0/1720.0 = 0.3721 37.21%
Ethylene ( C 2 H 4 \text{C}_2\text{H}_4 C 2 H 4 ) 80.0 80.0 / 1720.0 = 0.0465 80.0 / 1720.0 = 0.0465 80.0/1720.0 = 0.0465 4.65%
Methane ( CH 4 \text{CH}_4 CH 4 ) 80.0 80.0 / 1720.0 = 0.0465 80.0 / 1720.0 = 0.0465 80.0/1720.0 = 0.0465 4.65%
Nitrogen ( N 2 \text{N}_2 N 2 ) 100.0 100.0 / 1720.0 = 0.0581 100.0 / 1720.0 = 0.0581 100.0/1720.0 = 0.0581 5.81%
- Total 1,720.0 1.0000 100.00%
- Step 3: Verification via Independent Atomic Balances
To prove mathematical rigor, verify using atomic Carbon and Hydrogen balances:
Carbon Atom Balance (lb-atom C/h) : Carbon In = 900.0 lbmol C 3 H 8 × 3 C/molecule = 2 , 700.0 lb-atom C/h \text{Carbon In} = 900.0\text{ lbmol }\text{C}_3\text{H}_8 \times 3\text{ C/molecule} = \mathbf{2,700.0\text{ lb-atom C/h}} Carbon In = 900.0 lbmol C 3 H 8 × 3 C/molecule = 2 , 700.0 lb-atom C/h Carbon Out = ( 180.0 × 3 ) + ( 640.0 × 3 ) + ( 80.0 × 2 ) + ( 80.0 × 1 ) \text{Carbon Out} = (180.0 \times 3) + (640.0 \times 3) + (80.0 \times 2) + (80.0 \times 1) Carbon Out = ( 180.0 × 3 ) + ( 640.0 × 3 ) + ( 80.0 × 2 ) + ( 80.0 × 1 ) Carbon Out = 540.0 + 1 , 920.0 + 160.0 + 80.0 = 2 , 700.0 lb-atom C/h (Exact Closure) \text{Carbon Out} = 540.0 + 1,920.0 + 160.0 + 80.0 = \mathbf{2,700.0\text{ lb-atom C/h (Exact Closure)}} Carbon Out = 540.0 + 1 , 920.0 + 160.0 + 80.0 = 2 , 700.0 lb-atom C/h (Exact Closure)
Hydrogen Atom Balance (lb-atom H/h) : Hydrogen In = 900.0 lbmol C 3 H 8 × 8 H/molecule = 7 , 200.0 lb-atom H/h \text{Hydrogen In} = 900.0\text{ lbmol }\text{C}_3\text{H}_8 \times 8\text{ H/molecule} = \mathbf{7,200.0\text{ lb-atom H/h}} Hydrogen In = 900.0 lbmol C 3 H 8 × 8 H/molecule = 7 , 200.0 lb-atom H/h Hydrogen Out = ( 180.0 × 8 ) + ( 640.0 × 6 ) + ( 640.0 × 2 ) + ( 80.0 × 4 ) + ( 80.0 × 4 ) \text{Hydrogen Out} = (180.0 \times 8) + (640.0 \times 6) + (640.0 \times 2) + (80.0 \times 4) + (80.0 \times 4) Hydrogen Out = ( 180.0 × 8 ) + ( 640.0 × 6 ) + ( 640.0 × 2 ) + ( 80.0 × 4 ) + ( 80.0 × 4 ) Hydrogen Out = 1 , 440.0 + 3 , 840.0 + 1 , 280.0 + 320.0 + 320.0 = 7 , 200.0 lb-atom H/h (Exact Closure) \text{Hydrogen Out} = 1,440.0 + 3,840.0 + 1,280.0 + 320.0 + 320.0 = \mathbf{7,200.0\text{ lb-atom H/h (Exact Closure)}} Hydrogen Out = 1 , 440.0 + 3 , 840.0 + 1 , 280.0 + 320.0 + 320.0 = 7 , 200.0 lb-atom H/h (Exact Closure)
Step 4: Fractional Yield of Propylene
Based on propane fed: Y = n ˙ propylene, formed n ˙ propane, fed × ( 1 / 1 ) = 640.0 lbmol/h 900.0 lbmol/h = 0.7111 (71.11%) Y = \frac{\dot{n}_{\text{propylene, formed}}}{\dot{n}_{\text{propane, fed}} \times (1/1)} = \frac{640.0\text{ lbmol/h}}{900.0\text{ lbmol/h}} = \mathbf{0.7111\text{ (71.11\%)}} Y = n ˙ propane, fed × ( 1/1 ) n ˙ propylene, formed = 900.0 lbmol/h 640.0 lbmol/h = 0.7111 (71.11%)
Notice the fundamental relationship: Yield = Conversion × Selectivity to Propane Consumed = 0.800 × ( 640.0 / 720.0 ) = 0.800 × 0.8889 = 0.7111 \text{Yield} = \text{Conversion} \times \text{Selectivity to Propane Consumed} = 0.800 \times (640.0 / 720.0) = 0.800 \times 0.8889 = 0.7111 Yield = Conversion × Selectivity to Propane Consumed = 0.800 × ( 640.0/720.0 ) = 0.800 × 0.8889 = 0.7111 .