Study guide

20.2 Mechanical Integrity, Reliability, and Failure Mechanisms

PE Chemical Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the PE Chemical Exam How to Use This Guide and the NCEES Handbook

2 Chapter 1: Material Balances & Flowsheet Calculations

1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations

3 Chapter 2: Energy Balances & Thermochemistry

2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances

4 Chapter 3: Fluid Statics & Incompressible Pipe Flow

3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations

5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up

6 Chapter 5: Thermodynamic Laws & Fundamental Relations

5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations

7 Chapter 6: Real Gases & Equations of State

6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions

8 Chapter 7: Phase & Chemical Reaction Equilibria

7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation

9 Chapter 8: Heat Transfer Mechanisms & Conduction

8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange

10 Chapter 9: Heat Exchanger Design & Phase Change

9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances

11 Chapter 10: Mass Transfer Fundamentals & Diffusion

10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

12 Chapter 11: Distillation Operations

11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components

13 Chapter 12: Rate-Controlled & Equilibrium Separations

12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations

14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors

13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations

15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis

14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models

16 Chapter 15: Physical & Transport Properties of Fluids

15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles

17 Chapter 16: Materials of Construction & Corrosion

16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention

18 Chapter 17: Process Safety & Pressure Relief Systems

17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment

19 Chapter 18: Process Control & Engineering Economics

18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems

20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance

19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation

21 Chapter 20: Plant Operation, Reliability & Continuous Improvement

20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting

20.2 Mechanical Integrity, Reliability, and Failure Mechanisms

Key Takeaways Explain This Topic AI

PSM mechanical integrity applies to pressure vessels and storage tanks, piping, relief and vent systems, emergency shutdown systems, controls including alarms and interlocks, and pumps , and requires inspection and testing following recognized and generally accepted good engineering practice (RAGAGEP).

Remaining life is ( t a c t u a l − t r e q u i r e d ) / corrosion rate (t_{actual} - t_{required}) / \text{corrosion rate} ( t a c t u a l ​ − t re q u i re d ​ ) / corrosion rate ; under API 510 and API 570 the internal or thickness inspection interval is the lesser of one-half the remaining life or 10 years .

Corrosion rate must be evaluated on both a long-term and a short-term basis, and the greater of the two governs, so that a recent acceleration is not masked by years of benign history.

For a constant failure rate, reliability is R ( t ) = e − λ t R(t) = e^{-\lambda t} R ( t ) = e − λ t with M T B F = 1 / λ MTBF = 1/\lambda MTBF = 1/ λ , and steady-state availability is (MTBF/(MTBF + MTTR)); redundancy multiplies unreliability, so (n) parallel units give R = 1 − ( 1 − R i ) n R = 1 - (1-R_i)^n R = 1 − ( 1 − R i ​ ) n .

Corrosion under insulation is most aggressive where the metal sits between roughly − 12 ∘ C -12^\circ\text{C} − 1 2 ∘ C and 175 ∘ C 175^\circ\text{C} 17 5 ∘ C , is invisible from outside, and is a leading cause of unexpected piping failures in insulated service.

Last updated: September 2026

20.2 Mechanical Integrity, Reliability, and Failure Mechanisms

The NCEES specification lists Process equipment and reliability (e.g., testing, maintenance, mechanical integrity, failure mechanisms) under Operation and Maintenance. Section 16.2 covered the electrochemistry of corrosion. This section covers the program that finds damage before it causes a loss of containment, and the arithmetic that decides how often to look.

1. The Mechanical Integrity Element

Under (1910.119(j)), mechanical integrity applies to:

  • Pressure vessels and storage tanks
  • Piping systems, including components such as valves
  • Relief and vent systems and devices
  • Emergency shutdown systems
  • Controls, including monitoring devices and sensors, alarms, and interlocks
  • Pumps

The program must include written procedures, trained maintenance personnel, inspection and testing at frequencies consistent with manufacturer recommendations and good engineering practice, documentation of every inspection, correction of deficiencies before further use (or in a safe and timely manner with interim measures), and quality assurance that new equipment is fabricated and installed to specification.

RAGAGEP — recognized and generally accepted good engineering practice — is the benchmark. The standards a chemical engineer is expected to name:

  • Standard Scope
  • API 510 Pressure vessel inspection, rating, repair, alteration
  • API 570 In-service piping inspection
  • API 653 Aboveground storage tank inspection and reconstruction
  • API 576 Inspection of pressure-relieving devices
  • API 580 / 581 Risk-based inspection methodology and quantitative basis
  • ASME BPVC Sec. VIII Pressure vessel design and construction (Section 16.1)
  • 2. Corrosion Rate, Remaining Life, and Inspection Interval

Thickness is monitored at fixed thickness measurement locations (TMLs) so that successive readings are comparable. Long-term rate = t i n i t i a l − t a c t u a l years between them Short-term rate = t p r e v i o u s − t a c t u a l years between them \text{Long-term rate} = \frac{t_{initial} - t_{actual}}{\text{years between them}} \qquad \text{Short-term rate} = \frac{t_{previous} - t_{actual}}{\text{years between them}} Long-term rate = years between them t ini t ia l ​ − t a c t u a l ​ ​ Short-term rate = years between them t p re v i o u s ​ − t a c t u a l ​ ​

The greater of the two governs. A component that corroded at 0.05 mm/yr 0.05\text{ mm/yr} 0.05 mm/yr for fifteen years and then at 0.60 mm/yr 0.60\text{ mm/yr} 0.60 mm/yr since the last inspection has a long-term average that looks harmless; using it would set an interval that lets the component fail. The short-term rate is what detects a process upset, a change in feedstock, or a failed corrosion inhibitor. Remaining life = t a c t u a l − t r e q u i r e d corrosion rate \text{Remaining life} = \frac{t_{actual} - t_{required}}{\text{corrosion rate}} Remaining life = corrosion rate t a c t u a l ​ − t re q u i re d ​ ​

where t r e q u i r e d t_{required} t re q u i re d ​ is the minimum thickness for the design pressure and temperature (Section 16.1), excluding the corrosion allowance — the corrosion allowance is what is being consumed, not what must be retained.

The interval rule. Under API 510 for vessels and API 570 for piping, the internal or on-stream thickness inspection interval is the lesser of one-half the remaining life or 10 years (shorter for high-consequence piping classes). External visual inspection is typically on a 5-year cycle.

Worked example. A vessel course has t n o m i n a l = 0.500 in t_{nominal} = 0.500\text{ in} t n o mina l ​ = 0.500 in , t r e q u i r e d = 0.300 in t_{required} = 0.300\text{ in} t re q u i re d ​ = 0.300 in , current measured thickness 0.380 in 0.380\text{ in} 0.380 in , and a governing corrosion rate of 0.008 in/yr 0.008\text{ in/yr} 0.008 in/yr . Remaining life = 0.380 − 0.300 0.008 = 0.080 0.008 = 10.0 years \text{Remaining life} = \frac{0.380 - 0.300}{0.008} = \frac{0.080}{0.008} = 10.0\text{ years} Remaining life = 0.008 0.380 − 0.300 ​ = 0.008 0.080 ​ = 10.0 years Interval = min ⁡ ( 1 2 ( 10.0 ) , 10 ) = 5.0 years \text{Interval} = \min\left( \tfrac{1}{2}(10.0),\ 10 \right) = 5.0\text{ years} Interval = min ( 2 1 ​ ( 10.0 ) , 10 ) = 5.0 years

The half-life rule exists so that the component is examined at least once more while enough wall remains to act on the finding. Inspecting at the full remaining life would mean the next look happens at the moment of retirement thickness.

3. Damage Mechanisms

Mechanism Conditions Characteristic signature

General corrosion Uniform attack in an aggressive bulk fluid Even wall loss; predictable, manageable by allowance

Pitting Chlorides, stagnant zones, deposits Deep local penetration with negligible weight loss; not caught by average thickness

Chloride SCC Austenitic stainless, chlorides, tensile stress, > ∼ 60 ∘ C > \sim 60^\circ\text{C} >∼ 6 0 ∘ C Branched transgranular cracking; catastrophic and fast

Corrosion under insulation (CUI) Insulated carbon steel, roughly (-12) to 175 ∘ C 175^\circ\text{C} 17 5 ∘ C , water ingress Hidden beneath the jacket; a leading cause of unexpected piping failure

HTHA Hydrogen at elevated temperature and partial pressure Methane formation at grain boundaries; governed by API 941 Nelson curves

Sulfidation Sulfur compounds above ∼ 260 ∘ C \sim 260^\circ\text{C} ∼ 26 0 ∘ C Scaling of carbon and low-alloy steel in hot hydrocarbon service

Creep (T > 0.4)- 0.5 T m 0.5 T_m 0.5 T m ​ Time-dependent deformation; Larson-Miller (Section 16.1)

Brittle fracture BCC steel below its DBTT Sudden cleavage, often on a cold startup or an autorefrigeration event

Erosion-corrosion High velocity, entrained solids, two-phase Grooved, horseshoe-shaped loss at elbows and downstream of restrictions

MIC Stagnant water, sulfate-reducing bacteria Localized pitting under deposits, often in hydrotest water left in place

Two of these deserve emphasis because they defeat ordinary inspection. CUI is invisible without removing the insulation, which is expensive, so it is inspected on a risk-prioritized basis targeting known water-ingress points: penetrations, supports, damaged jacketing, and lines that cycle through the damp temperature band. Pitting and SCC produce essentially no measurable general wall loss, so a thickness-only inspection program will report a healthy component right up to the through-wall leak; detecting them requires appropriate techniques such as visual examination, dye penetrant, or ultrasonic shear wave.

Risk-based inspection (API 580/581) allocates inspection effort by risk = probability of failure × consequence of failure \text{risk} = \text{probability of failure} \times \text{consequence of failure} risk = probability of failure × consequence of failure , concentrating resources on the small fraction of components that carry most of the risk rather than inspecting everything on a uniform calendar.

4. Reliability Mathematics

During the flat middle of the bathtub curve the failure rate λ \lambda λ is approximately constant, and: R ( t ) = e − λ t , M T B F = 1 λ R(t) = e^{-\lambda t}, \qquad MTBF = \frac{1}{\lambda} R ( t ) = e − λ t , MTBF = λ 1 ​ Failure rate lambda

  • ^
  • |\ /
  • | \ infant / wear-out
  • | \ mortality /
  • | \___________________________________/
  • | useful life (constant lambda)
  • +----------------------------------------------> time

Availability accounts for how long repairs take, not only how often failures occur: A = M T B F M T B F + M T T R A = \frac{MTBF}{MTBF + MTTR} A = MTBF + MTTR MTBF ​

A pump with M T B F = 8,000 h MTBF = 8{,}000\text{ h} MTBF = 8 , 000 h and M T T R = 40 h MTTR = 40\text{ h} MTTR = 40 h has A = 8,000 / 8,040 = 0.995 A = 8{,}000/8{,}040 = 0.995 A = 8 , 000/8 , 040 = 0.995 . Cutting (MTTR) to 10 h 10\text{ h} 10 h by stocking a spare rotating assembly raises (A) to (0.99875) — often cheaper per point of availability than extending (MTBF).

System architecture. For components in series (all must work), reliabilities multiply: R s y s = ∏ R i R_{sys} = \prod R_i R sys ​ = ∏ R i ​

For components in parallel (any one suffices), unreliabilities multiply: R s y s = 1 − ∏ ( 1 − R i ) R_{sys} = 1 - \prod (1 - R_i) R sys ​ = 1 − ∏ ( 1 − R i ​ )

Three parallel pumps each at (R = 0.90), with any one able to carry the duty, give R s y s = 1 − ( 0.10 ) 3 = 0.999 R_{sys} = 1 - (0.10)^3 = 0.999 R sys ​ = 1 − ( 0.10 ) 3 = 0.999 . The same three in series — as in a train where every unit must run — give R s y s = 0.90 3 = 0.729 R_{sys} = 0.90^3 = 0.729 R sys ​ = 0.9 0 3 = 0.729 . This asymmetry is why a long unspared chain of equipment has poor availability even when every individual item is good, and why sparing is applied to the specific items with the lowest (R).

Maintenance strategy follows from consequence:

  • Strategy Basis Use when
  • Run to failure React after breakdown Non-critical, cheap, redundant items
  • Preventive Fixed time or run-hours Known wear-out behavior

Predictive / condition-based Vibration, thermography, oil analysis, thickness Failure develops detectably over time

Proactive / RCM Eliminate the root cause Chronic repeat failures

Time-based preventive maintenance on an item with a constant failure rate is wasted effort: a memoryless failure process is no less likely to fail just after an overhaul than just before one, and the intervention itself introduces infant-mortality risk. Preventive replacement only pays where there is a genuine wear-out mechanism.