Study guide
7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
Key Takeaways Explain This Topic AI
Chemical reaction equilibrium at constant temperature and pressure is established when the total Gibbs free energy is minimized, corresponding to Delta G_rxn = sum(nu_i * mu_i) = 0.
The thermodynamic equilibrium constant K_a = exp(-Delta G_rxn^o / [R * T]) is a strict function of temperature alone; it is completely independent of total system pressure, reactant concentrations, or the presence of inerts.
The van 't Hoff equation [d(ln K_a)/dT = Delta H_rxn^o / (R * T^2)] dictates the thermal response of equilibrium: increasing temperature decreases K_a for exothermic reactions (Delta H_rxn^o < 0) and increases K_a for endothermic reactions (Delta H_rxn^o > 0).
Total system pressure shifts the equilibrium composition of gas-phase reactions through K_y = K_a * (P / P^o)^(-Delta nu); elevating pressure shifts equilibrium toward fewer gas moles (Delta nu < 0), whereas reducing pressure promotes expansion reactions (Delta nu > 0).
Adding an inert gas at constant total pressure dilutes the reacting mixture and acts identically to an overall pressure reduction, shifting the equilibrium toward the side with the larger number of gas moles (Delta nu > 0).
Last updated: September 2026
7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
Thermodynamic reaction equilibrium defines the absolute upper limit of conversion, selectivity, and product yield achievable in chemical reactors. Regardless of catalyst activity, residence time, or reactor geometry, no kinetic mechanism can drive a reaction past its thermodynamic equilibrium boundary. On the NCEES PE Chemical Exam , reaction equilibria questions test your ability to determine standard free energies ( Δ G r x n ∘ \Delta G_{rxn}^\circ Δ G r x n ∘ ), evaluate temperature-dependent equilibrium constants ( K a K_a K a ) using the van 't Hoff equation , formulate stoichiometric mole tables , and predict equilibrium shifts using Le Chatelier's Principle .
1. Thermodynamic Criterion of Chemical Reaction Equilibrium
Consider a closed chemical system at constant temperature ( T T T ) and pressure ( P P P ) undergoing a reversible chemical reaction represented by the general stoichiometric equation: ∑ i = 1 C ν i A i = 0 \sum_{i=1}^C \nu_i A_i = 0 i = 1 ∑ C ν i A i = 0
Where:
A i A_i A i represents chemical species i i i .
ν i \nu_i ν i is the stoichiometric coefficient: positive for products , negative for reactants , and zero for inerts .
From the fundamental property relation, the differential change in total Gibbs free energy of the reacting mixture is: d G T , P = ∑ i = 1 C μ i d n i dG_{T, P} = \sum_{i=1}^C \mu_i dn_i d G T , P = i = 1 ∑ C μ i d n i
The Extent of Reaction ( ξ \xi ξ )
The change in moles of each species i i i during reaction is governed by stoichiometry through the extent of reaction ( ξ \xi ξ , having units of moles): d n i = ν i d ξ ⟹ n i = n i , 0 + ν i ξ dn_i = \nu_i d\xi \implies n_i = n_{i,0} + \nu_i \xi d n i = ν i d ξ ⟹ n i = n i , 0 + ν i ξ
Substituting d n i = ν i d ξ dn_i = \nu_i d\xi d n i = ν i d ξ into the Gibbs energy differential: d G T , P = ( ∑ i = 1 C ν i μ i ) d ξ dG_{T, P} = \left( \sum_{i=1}^C \nu_i \mu_i \right) d\xi d G T , P = ( i = 1 ∑ C ν i μ i ) d ξ
At constant T T T and P P P , a spontaneous reaction proceeds in the direction that decreases Gibbs energy ( d G < 0 dG < 0 d G < 0 ). At equilibrium, the system reaches the minimum of the Gibbs energy curve ( d G / d ξ = 0 dG/d\xi = 0 d G / d ξ = 0 ): ( ∂ G ∂ ξ ) T , P = ∑ i = 1 C ν i μ i ≡ Δ G r x n = 0 \left( \frac{\partial G}{\partial \xi} \right)_{T, P} = \sum_{i=1}^C \nu_i \mu_i \equiv \Delta G_{rxn} = 0 ( ∂ ξ ∂ G ) T , P = i = 1 ∑ C ν i μ i ≡ Δ G r x n = 0 G ^
- | \ /
- | \ /
- | \ /
- | \ /
- | \ Spontaneous /
- | \ Forward /
- | \ (dG/dxi < 0) /
- | \ /
- | \ /
- | '--.__ __.--'
- | \____/ <--- EQUILIBRIUM: (dG/dxi) = 0
- +--------------------------------------------------------> xi (Extent)
- Reactants (xi = 0) Complete Conversion (xi_max)
- 2. Standard Gibbs Energy of Reaction and the Equilibrium Constant ( K a K_a K a )
The chemical potential of species i i i in a mixture is related to its thermodynamic activity ( a i a_i a i ): μ i = μ i ∘ ( T ) + R T ln a i \mu_i = \mu_i^\circ(T) + R T \ln a_i μ i = μ i ∘ ( T ) + RT ln a i
Where μ i ∘ ( T ) \mu_i^\circ(T) μ i ∘ ( T ) is the chemical potential of pure species i i i in its standard state at temperature T T T and standard pressure P ∘ P^\circ P ∘ ( 1.0 bar 1.0\text{ bar} 1.0 bar or 1.0 atm 1.0\text{ atm} 1.0 atm ). Substituting this into the equilibrium condition ∑ ν i μ i = 0 \sum \nu_i \mu_i = 0 ∑ ν i μ i = 0 : ∑ i = 1 C ν i ( μ i ∘ + R T ln a i ) = 0 \sum_{i=1}^C \nu_i \left( \mu_i^\circ + R T \ln a_i \right) = 0 i = 1 ∑ C ν i ( μ i ∘ + RT ln a i ) = 0 ∑ i = 1 C ν i μ i ∘ + R T ∑ i = 1 C ln ( a i ν i ) = 0 \sum_{i=1}^C \nu_i \mu_i^\circ + R T \sum_{i=1}^C \ln\left( a_i^{\nu_i} \right) = 0 i = 1 ∑ C ν i μ i ∘ + RT i = 1 ∑ C ln ( a i ν i ) = 0 ∑ i = 1 C ν i μ i ∘ + R T ln ( ∏ i = 1 C a i ν i ) = 0 \sum_{i=1}^C \nu_i \mu_i^\circ + R T \ln\left( \prod_{i=1}^C a_i^{\nu_i} \right) = 0 i = 1 ∑ C ν i μ i ∘ + RT ln ( i = 1 ∏ C a i ν i ) = 0
The Standard Gibbs Free Energy Change ( Δ G r x n ∘ \Delta G_{rxn}^\circ Δ G r x n ∘ )
The summation ∑ ν i μ i ∘ \sum \nu_i \mu_i^\circ ∑ ν i μ i ∘ defines the standard Gibbs energy change of reaction at temperature T T T : Δ G r x n ∘ ( T ) ≡ ∑ i = 1 C ν i μ i ∘ ( T ) = ∑ i = 1 C ν i Δ G f , i ∘ ( T ) \Delta G_{rxn}^\circ(T) \equiv \sum_{i=1}^C \nu_i \mu_i^\circ(T) = \sum_{i=1}^C \nu_i \Delta G_{f,i}^\circ(T) Δ G r x n ∘ ( T ) ≡ i = 1 ∑ C ν i μ i ∘ ( T ) = i = 1 ∑ C ν i Δ G f , i ∘ ( T )
Where Δ G f , i ∘ ( T ) \Delta G_{f,i}^\circ(T) Δ G f , i ∘ ( T ) is the standard Gibbs energy of formation of species i i i from its constituent elements in their reference states at temperature T T T .
The Thermodynamic Equilibrium Constant ( K a K_a K a )
Defining the thermodynamic equilibrium constant ( K a K_a K a ) as the product of activities at equilibrium: K a ≡ ∏ i = 1 C a i ν i K_a \equiv \prod_{i=1}^C a_i^{\nu_i} K a ≡ i = 1 ∏ C a i ν i
Yields the central thermodynamic identity of chemical equilibria: Δ G r x n ∘ = − R T ln K a ⟺ K a = exp ( − Δ G r x n ∘ R T ) \Delta G_{rxn}^\circ = -R T \ln K_a \iff K_a = \exp\left( -\frac{\Delta G_{rxn}^\circ}{R T} \right) Δ G r x n ∘ = − RT ln K a ⟺ K a = exp ( − RT Δ G r x n ∘ )
Important
The Cardinal Rule of Chemical Equilibrium: Because the standard state for each chemical species is defined at a fixed standard pressure ( P ∘ = 1.0 bar P^\circ = 1.0\text{ bar} P ∘ = 1.0 bar ), the standard Gibbs energy Δ G r x n ∘ ( T ) \Delta G_{rxn}^\circ(T) Δ G r x n ∘ ( T ) depends strictly on temperature .
Consequently, the thermodynamic equilibrium constant K a K_a K a is a function of temperature alone: K a = K a ( T ) K_a = K_a(T) K a = K a ( T ) .
Total system pressure, inert gas addition, feed composition, and catalyst presence have zero effect on K a K_a K a !
3. Gas-Phase Reaction Equilibria Formulation
For gas-phase reactions, the activity of species i i i is defined relative to the standard state of pure ideal gas at P ∘ = 1.0 bar P^\circ = 1.0\text{ bar} P ∘ = 1.0 bar ( 100 kPa 100\text{ kPa} 100 kPa or 1.0 atm 1.0\text{ atm} 1.0 atm ): a i = f i P ∘ = y i ϕ i P P ∘ a_i = \frac{f_i}{P^\circ} = \frac{y_i \phi_i P}{P^\circ} a i = P ∘ f i = P ∘ y i ϕ i P
Substituting this into the activity equilibrium constant expression: K a = ∏ i = 1 C ( y i ϕ i P P ∘ ) ν i = ( P P ∘ ) ∑ ν i ( ∏ i = 1 C y i ν i ) ( ∏ i = 1 C ϕ i ν i ) K_a = \prod_{i=1}^C \left( \frac{y_i \phi_i P}{P^\circ} \right)^{\nu_i} = \left( \frac{P}{P^\circ} \right)^{\sum \nu_i} \left( \prod_{i=1}^C y_i^{\nu_i} \right) \left( \prod_{i=1}^C \phi_i^{\nu_i} \right) K a = i = 1 ∏ C ( P ∘ y i ϕ i P ) ν i = ( P ∘ P ) ∑ ν i ( i = 1 ∏ C y i ν i ) ( i = 1 ∏ C ϕ i ν i )
Defining:
Δ ν ≡ ∑ i = 1 C ν i \Delta \nu \equiv \sum_{i=1}^C \nu_i Δ ν ≡ ∑ i = 1 C ν i = net change in moles of gas per stoichiometric reaction unit.
K y ≡ ∏ i = 1 C y i ν i K_y \equiv \prod_{i=1}^C y_i^{\nu_i} K y ≡ ∏ i = 1 C y i ν i = mole fraction composition factor.
K ϕ ≡ ∏ i = 1 C ϕ i ν i K_\phi \equiv \prod_{i=1}^C \phi_i^{\nu_i} K ϕ ≡ ∏ i = 1 C ϕ i ν i = mixture fugacity coefficient factor ( K ϕ ≈ 1.0 K_\phi \approx 1.0 K ϕ ≈ 1.0 at low to moderate pressures).
The general gas-phase equilibrium expression is: K a = ( P P ∘ ) Δ ν K y K ϕ K_a = \left( \frac{P}{P^\circ} \right)^{\Delta \nu} K_y K_\phi K a = ( P ∘ P ) Δ ν K y K ϕ
Ideal Gas Mixture Simplification
At low to moderate operating pressures ( P < 10 − 15 bar P < 10-15\text{ bar} P < 10 − 15 bar ), gas fugacity coefficients approach unity ( K ϕ ≈ 1.00 K_\phi \approx 1.00 K ϕ ≈ 1.00 ). The relationship simplifies to: K a = ( P P ∘ ) Δ ν K y ⟹ K y = K a ( P P ∘ ) − Δ ν K_a = \left( \frac{P}{P^\circ} \right)^{\Delta \nu} K_y \implies K_y = K_a \left( \frac{P}{P^\circ} \right)^{-\Delta \nu} K a = ( P ∘ P ) Δ ν K y ⟹ K y = K a ( P ∘ P ) − Δ ν
This crucial equation reveals how system pressure governs equilibrium composition ( K y K_y K y ) while K a K_a K a remains constant!
4. Temperature Dependence of K a K_a K a : The van 't Hoff Equation
To determine how the equilibrium constant changes when reactor temperature varies from standard reference temperature ( T 0 = 298.15 K T_0 = 298.15\text{ K} T 0 = 298.15 K ) to operating temperature ( T T T ), we apply the Gibbs-Helmholtz equation : [ ∂ ( G / T ) ∂ T ] P = − H T 2 ⟹ d ( Δ G r x n ∘ / T ) d T = − Δ H r x n ∘ T 2 \left[ \frac{\partial (G/T)}{\partial T} \right]_P = -\frac{H}{T^2} \implies \frac{d(\Delta G_{rxn}^\circ / T)}{dT} = -\frac{\Delta H_{rxn}^\circ}{T^2} [ ∂ T ∂ ( G / T ) ] P = − T 2 H ⟹ d T d ( Δ G r x n ∘ / T ) = − T 2 Δ H r x n ∘
Substituting Δ G r x n ∘ / T = − R ln K a \Delta G_{rxn}^\circ / T = -R \ln K_a Δ G r x n ∘ / T = − R ln K a yields the differential van 't Hoff equation : d ( ln K a ) d T = Δ H r x n ∘ ( T ) R T 2 \frac{d(\ln K_a)}{dT} = \frac{\Delta H_{rxn}^\circ(T)}{R T^2} d T d ( ln K a ) = R T 2 Δ H r x n ∘ ( T )
Where Δ H r x n ∘ ( T ) \Delta H_{rxn}^\circ(T) Δ H r x n ∘ ( T ) is the standard enthalpy of reaction at temperature T T T : Δ H r x n ∘ = ∑ i = 1 C ν i Δ H f , i ∘ \Delta H_{rxn}^\circ = \sum_{i=1}^C \nu_i \Delta H_{f,i}^\circ Δ H r x n ∘ = i = 1 ∑ C ν i Δ H f , i ∘
Integrated Form (Constant Heat of Reaction Assumption)
Over moderate temperature ranges where Δ H r x n ∘ \Delta H_{rxn}^\circ Δ H r x n ∘ is approximately constant (i.e., Δ C p = ∑ ν i C p , i ≈ 0 \Delta C_p = \sum \nu_i C_{p,i} \approx 0 Δ C p = ∑ ν i C p , i ≈ 0 ): ∫ K a ( T 1 ) K a ( T 2 ) d ln K a = Δ H r x n ∘ R ∫ T 1 T 2 d T T 2 \int_{K_a(T_1)}^{K_a(T_2)} d\ln K_a = \frac{\Delta H_{rxn}^\circ}{R} \int_{T_1}^{T_2} \frac{dT}{T^2} ∫ K a ( T 1 ) K a ( T 2 ) d ln K a = R Δ H r x n ∘ ∫ T 1 T 2 T 2 d T ln ( K a ( T 2 ) K a ( T 1 ) ) = − Δ H r x n ∘ R ( 1 T 2 − 1 T 1 ) = Δ H r x n ∘ R ( T 2 − T 1 T 1 T 2 ) \ln\left( \frac{K_a(T_2)}{K_a(T_1)} \right) = -\frac{\Delta H_{rxn}^\circ}{R} \left( \frac{1}{T_2} - \frac{1}{T_1} \right) = \frac{\Delta H_{rxn}^\circ}{R} \left( \frac{T_2 - T_1}{T_1 T_2} \right) ln ( K a ( T 1 ) K a ( T 2 ) ) = − R Δ H r x n ∘ ( T 2 1 − T 1 1 ) = R Δ H r x n ∘ ( T 1 T 2 T 2 − T 1 )
Thermal Response Directions
Endothermic Reactions ( Δ H r x n ∘ > 0 \Delta H_{rxn}^\circ > 0 Δ H r x n ∘ > 0 , absorbs heat) : d ( ln K a ) d T > 0 \frac{d(\ln K_a)}{dT} > 0 d T d ( ln K a ) > 0 Increasing temperature increases K a K_a K a . Equilibrium shifts toward the products, increasing conversion.
Exothermic Reactions ( Δ H r x n ∘ < 0 \Delta H_{rxn}^\circ < 0 Δ H r x n ∘ < 0 , releases heat) : d ( ln K a ) d T < 0 \frac{d(\ln K_a)}{dT} < 0 d T d ( ln K a ) < 0 Increasing temperature decreases K a K_a K a . Equilibrium shifts toward the reactants, suppressing conversion.
Rigorous Integration (Temperature-Dependent Heat Capacity)
When Δ C p ≠ 0 \Delta C_p \ne 0 Δ C p = 0 , Δ H r x n ∘ ( T ) \Delta H_{rxn}^\circ(T) Δ H r x n ∘ ( T ) varies with temperature according to Kirchhoff's Law: Δ H r x n ∘ ( T ) = Δ H r x n ∘ ( T 0 ) + ∫ T 0 T Δ C p d T \Delta H_{rxn}^\circ(T) = \Delta H_{rxn}^\circ(T_0) + \int_{T_0}^T \Delta C_p dT Δ H r x n ∘ ( T ) = Δ H r x n ∘ ( T 0 ) + ∫ T 0 T Δ C p d T ln K a ( T ) = ln K a ( T 0 ) + 1 R ∫ T 0 T Δ H r x n ∘ ( T ) T 2 d T \ln K_a(T) = \ln K_a(T_0) + \frac{1}{R} \int_{T_0}^T \frac{\Delta H_{rxn}^\circ(T)}{T^2} dT ln K a ( T ) = ln K a ( T 0 ) + R 1 ∫ T 0 T T 2 Δ H r x n ∘ ( T ) d T
5. Stoichiometric Table and Reaction Extent Formulation
To solve reaction equilibrium problems systematically on the PE exam, always construct a Stoichiometric Mole Table in terms of the extent of reaction ( ξ \xi ξ ) or the fractional conversion ( X A X_A X A ) of the limiting reactant.
General Stoichiometric Balance Table
Species ( i i i ) Initial Moles ( n i , 0 n_{i,0} n i , 0 ) Change in Moles ( Δ n i = ν i ξ \Delta n_i = \nu_i \xi Δ n i = ν i ξ ) Equilibrium Moles ( n i n_i n i ) Equilibrium Mole Fraction ( y i = n i / n t o t y_i = n_i / n_{tot} y i = n i / n t o t )
Reactant A n A , 0 n_{A,0} n A , 0 ν A ξ \nu_A \xi ν A ξ (where ν A < 0 \nu_A < 0 ν A < 0 ) n A = n A , 0 + ν A ξ n_A = n_{A,0} + \nu_A \xi n A = n A , 0 + ν A ξ y A = ( n A , 0 + ν A ξ ) / n t o t y_A = (n_{A,0} + \nu_A \xi) / n_{tot} y A = ( n A , 0 + ν A ξ ) / n t o t
Reactant B n B , 0 n_{B,0} n B , 0 ν B ξ \nu_B \xi ν B ξ (where ν B < 0 \nu_B < 0 ν B < 0 ) n B = n B , 0 + ν B ξ n_B = n_{B,0} + \nu_B \xi n B = n B , 0 + ν B ξ y B = ( n B , 0 + ν B ξ ) / n t o t y_B = (n_{B,0} + \nu_B \xi) / n_{tot} y B = ( n B , 0 + ν B ξ ) / n t o t
Product C n C , 0 n_{C,0} n C , 0 ν C ξ \nu_C \xi ν C ξ (where ν C > 0 \nu_C > 0 ν C > 0 ) n C = n C , 0 + ν C ξ n_C = n_{C,0} + \nu_C \xi n C = n C , 0 + ν C ξ y C = ( n C , 0 + ν C ξ ) / n t o t y_C = (n_{C,0} + \nu_C \xi) / n_{tot} y C = ( n C , 0 + ν C ξ ) / n t o t
Inerts (I) n I n_{I} n I 0 0 0 n I n_I n I y I = n I / n t o t y_I = n_I / n_{tot} y I = n I / n t o t
TOTAL n t o t , 0 n_{tot,0} n t o t , 0 Δ ν ξ \Delta \nu \xi Δ ν ξ n t o t = n t o t , 0 + Δ ν ξ n_{tot} = n_{tot,0} + \Delta \nu \xi n t o t = n t o t , 0 + Δ ν ξ 1.000 1.000 1.000
Where:
n t o t , 0 = n A , 0 + n B , 0 + n C , 0 + n I n_{tot,0} = n_{A,0} + n_{B,0} + n_{C,0} + n_I n t o t , 0 = n A , 0 + n B , 0 + n C , 0 + n I
Δ ν = ∑ ν i = ν A + ν B + ν C \Delta \nu = \sum \nu_i = \nu_A + \nu_B + \nu_C Δ ν = ∑ ν i = ν A + ν B + ν C
Fractional conversion of limiting reactant A A A : X A = n A , 0 − n A n A , 0 = − ν A ξ n A , 0 ⟹ ξ = n A , 0 X A − ν A X_A = \frac{n_{A,0} - n_A}{n_{A,0}} = \frac{-\nu_A \xi}{n_{A,0}} \implies \xi = \frac{n_{A,0} X_A}{-\nu_A} X A = n A , 0 n A , 0 − n A = n A , 0 − ν A ξ ⟹ ξ = − ν A n A , 0 X A
6. Le Chatelier's Principle: Engineering Process Levers
Henri Louis Le Chatelier (1884) stated that if a system at chemical equilibrium experiences a perturbation in temperature, pressure, or concentration, the equilibrium shifts in the direction that partially offsets the imposed change.
1. Effect of Temperature
Governed entirely by the sign of Δ H r x n ∘ \Delta H_{rxn}^\circ Δ H r x n ∘ through the van 't Hoff equation.
Exothermic ( Δ H r x n ∘ < 0 \Delta H_{rxn}^\circ < 0 Δ H r x n ∘ < 0 ): Adding heat (raising T T T ) shifts equilibrium to the left (reactants). Cooling shifts to the right.
Endothermic ( Δ H r x n ∘ > 0 \Delta H_{rxn}^\circ > 0 Δ H r x n ∘ > 0 ): Adding heat (raising T T T ) shifts equilibrium to the right (products).
2. Effect of Total Pressure
Pressure does not change K a K_a K a . It shifts equilibrium through the term ( P / P ∘ ) − Δ ν (P/P^\circ)^{-\Delta \nu} ( P / P ∘ ) − Δ ν in K y = K a ( P / P ∘ ) − Δ ν K_y = K_a (P/P^\circ)^{-\Delta \nu} K y = K a ( P / P ∘ ) − Δ ν .
If Δ ν < 0 \Delta \nu < 0 Δ ν < 0 (mole-reducing reaction, e.g., N 2 + 3 H 2 ⇌ 2 NH 3 \text{N}_2 + 3\text{H}_2 \rightleftharpoons 2\text{NH}_3 N 2 + 3 H 2 ⇌ 2 NH 3 , Δ ν = − 2 \Delta \nu = -2 Δ ν = − 2 ) : K y = K a ( P P ∘ ) + 2 K_y = K_a \left( \frac{P}{P^\circ} \right)^{+2} K y = K a ( P ∘ P ) + 2 Increasing total pressure P P P increases K y K_y K y , shifting equilibrium toward the product side (higher conversion). This is why Haber-Bosch ammonia synthesis operates at 150 − 250 bar 150-250\text{ bar} 150 − 250 bar .
If Δ ν > 0 \Delta \nu > 0 Δ ν > 0 (mole-expanding reaction, e.g., CH 4 + H 2 O ⇌ CO + 3 H 2 \text{CH}_4 + \text{H}_2\text{O} \rightleftharpoons \text{CO} + 3\text{H}_2 CH 4 + H 2 O ⇌ CO + 3 H 2 , Δ ν = + 2 \Delta \nu = +2 Δ ν = + 2 ) : K y = K a ( P P ∘ ) − 2 K_y = K_a \left( \frac{P}{P^\circ} \right)^{-2} K y = K a ( P ∘ P ) − 2 Increasing total pressure suppresses conversion. Lowering pressure or pulling vacuum promotes product yield.
If Δ ν = 0 \Delta \nu = 0 Δ ν = 0 (equimolar reaction, e.g., CO + H 2 O ⇌ CO 2 + H 2 \text{CO} + \text{H}_2\text{O} \rightleftharpoons \text{CO}_2 + \text{H}_2 CO + H 2 O ⇌ CO 2 + H 2 ) : K y = K a K_y = K_a K y = K a Total pressure has zero effect on equilibrium conversion or mole fractions!
3. Effect of Inerts (Steam, Nitrogen, Argon)
Inerts Added at Constant Total Pressure ( P = const P = \text{const} P = const ) :
Adding inerts increases total moles n t o t n_{tot} n t o t , which decreases the partial pressures of reacting components. This dilution acts identically to a reduction in total system pressure :
For Δ ν > 0 \Delta \nu > 0 Δ ν > 0 : Adding inerts increases equilibrium conversion (e.g., steam added to ethylbenzene dehydrogenation to produce styrene).
For Δ ν < 0 \Delta \nu < 0 Δ ν < 0 : Adding inerts decreases equilibrium conversion.
For Δ ν = 0 \Delta \nu = 0 Δ ν = 0 : Adding inerts has no effect on reactant conversion.
Inerts Added at Constant Volume ( V = const V = \text{const} V = const ) :
In a rigid vessel, adding inerts raises total pressure but leaves the concentrations ( n i / V n_i/V n i / V ) and partial pressures ( P i P_i P i ) of the reactants unchanged. Equilibrium conversion does not shift .
4. Effect of Catalysts
Catalysts lower the activation energies ( E a E_a E a ) of the forward and reverse reactions by the exact same amount.
Catalysts increase the rate of approaching equilibrium, but have zero effect on Δ G r x n ∘ \Delta G_{rxn}^\circ Δ G r x n ∘ , K a K_a K a , or equilibrium conversion .
7. Summary Table: Process Perturbations & Reaction Equilibrium Shifts
Process Modification Effect on K a K_a K a Effect on Conversion if Δ ν < 0 \Delta \nu < 0 Δ ν < 0 Effect on Conversion if Δ ν = 0 \Delta \nu = 0 Δ ν = 0 Effect on Conversion if Δ ν > 0 \Delta \nu > 0 Δ ν > 0
Increase Temperature (Exothermic: Δ H ∘ < 0 \Delta H^\circ < 0 Δ H ∘ < 0 ) Decreases Decreases Decreases Decreases
Increase Temperature (Endothermic: Δ H ∘ > 0 \Delta H^\circ > 0 Δ H ∘ > 0 ) Increases Increases Increases Increases
- Increase Total Pressure ( P P P ) No Effect Increases No Effect Decreases
- Decrease Total Pressure ( P P P ) No Effect Decreases No Effect Increases
- Add Inerts at Constant Pressure ( P P P ) No Effect Decreases No Effect Increases
- Add Inerts at Constant Volume ( V V V ) No Effect No Effect No Effect No Effect
- Introduce Catalyst No Effect No Effect (Faster kinetics only) No Effect No Effect
Remove Product Continuously No Effect Increases ( Q < K Q < K Q < K ) Increases ( Q < K Q < K Q < K ) Increases ( Q < K Q < K Q < K )
- 8. Comprehensive Worked Numerical Example: High-Temperature Sulfur Dioxide Oxidation
- Problem Statement
In a contact process sulfuric acid plant, sulfur dioxide is catalytically oxidized to sulfur trioxide across a vanadium pentoxide ( V 2 O 5 \text{V}_2\text{O}_5 V 2 O 5 ) catalyst bed: SO 2 ( g ) + 1 2 O 2 ( g ) ⇌ SO 3 ( g ) \text{SO}_2(g) + \frac{1}{2}\text{O}_2(g) \rightleftharpoons \text{SO}_3(g) SO 2 ( g ) + 2 1 O 2 ( g ) ⇌ SO 3 ( g )
Standard Thermodynamic Data at T 0 = 298.15 K T_0 = 298.15\text{ K} T 0 = 298.15 K ( P ∘ = 1.00 bar P^\circ = 1.00\text{ bar} P ∘ = 1.00 bar ):
SO 2 ( g ) \text{SO}_2(g) SO 2 ( g ) : Δ H f , 298 ∘ = − 296.83 kJ/mol \Delta H_{f,298}^\circ = -296.83\text{ kJ/mol} Δ H f , 298 ∘ = − 296.83 kJ/mol , Δ G f , 298 ∘ = − 300.19 kJ/mol \Delta G_{f,298}^\circ = -300.19\text{ kJ/mol} Δ G f , 298 ∘ = − 300.19 kJ/mol
O 2 ( g ) \text{O}_2(g) O 2 ( g ) : Δ H f , 298 ∘ = 0.00 kJ/mol \Delta H_{f,298}^\circ = 0.00\text{ kJ/mol} Δ H f , 298 ∘ = 0.00 kJ/mol , Δ G f , 298 ∘ = 0.00 kJ/mol \Delta G_{f,298}^\circ = 0.00\text{ kJ/mol} Δ G f , 298 ∘ = 0.00 kJ/mol
SO 3 ( g ) \text{SO}_3(g) SO 3 ( g ) : Δ H f , 298 ∘ = − 395.72 kJ/mol \Delta H_{f,298}^\circ = -395.72\text{ kJ/mol} Δ H f , 298 ∘ = − 395.72 kJ/mol , Δ G f , 298 ∘ = − 371.06 kJ/mol \Delta G_{f,298}^\circ = -371.06\text{ kJ/mol} Δ G f , 298 ∘ = − 371.06 kJ/mol
The converter operates at a temperature of T = 700.0 K T = 700.0\text{ K} T = 700.0 K and an absolute pressure of P = 2.00 bar P = 2.00\text{ bar} P = 2.00 bar . The feed gas enters with the molar ratio:
- 1.00 mol SO 2 1.00\text{ mol } \text{SO}_2 1.00 mol SO 2
- 0.80 mol O 2 0.80\text{ mol } \text{O}_2 0.80 mol O 2
- 4.00 mol N 2 4.00\text{ mol } \text{N}_2 4.00 mol N 2 (inert carrier gas)
Calculate:
The standard enthalpy change ( Δ H r x n , 298 ∘ \Delta H_{rxn,298}^\circ Δ H r x n , 298 ∘ ) and standard Gibbs free energy change ( Δ G r x n , 298 ∘ \Delta G_{rxn,298}^\circ Δ G r x n , 298 ∘ ) at 298.15 K 298.15\text{ K} 298.15 K .
The thermodynamic equilibrium constant K a K_a K a at 298.15 K 298.15\text{ K} 298.15 K .
The equilibrium constant K a K_a K a at converter operating temperature T = 700.0 K T = 700.0\text{ K} T = 700.0 K assuming constant Δ H r x n ∘ \Delta H_{rxn}^\circ Δ H r x n ∘ .
The stoichiometric change in gas moles ( Δ ν \Delta \nu Δ ν ) and the expression for K y K_y K y .
Formulate the equilibrium composition in terms of SO 2 \text{SO}_2 SO 2 conversion ( X X X ) and determine the equilibrium conversion at 700.0 K 700.0\text{ K} 700.0 K and 2.00 bar 2.00\text{ bar} 2.00 bar .
Step 1: Standard Heats and Free Energies of Reaction at 298.15 K 298.15\text{ K} 298.15 K Δ H r x n , 298 ∘ = Δ H f ∘ ( SO 3 ) − Δ H f ∘ ( SO 2 ) − 0.5 Δ H f ∘ ( O 2 ) \Delta H_{rxn,298}^\circ = \Delta H_{f}^\circ(\text{SO}_3) - \Delta H_{f}^\circ(\text{SO}_2) - 0.5 \Delta H_{f}^\circ(\text{O}_2) Δ H r x n , 298 ∘ = Δ H f ∘ ( SO 3 ) − Δ H f ∘ ( SO 2 ) − 0.5Δ H f ∘ ( O 2 ) Δ H r x n , 298 ∘ = − 395.72 − ( − 296.83 ) − 0.5 ( 0 ) = − 98.89 kJ/mol = − 98 , 890 J/mol \Delta H_{rxn,298}^\circ = -395.72 - (-296.83) - 0.5(0) = \mathbf{-98.89\text{ kJ/mol}} = -98,890\text{ J/mol} Δ H r x n , 298 ∘ = − 395.72 − ( − 296.83 ) − 0.5 ( 0 ) = − 98.89 kJ/mol = − 98 , 890 J/mol Δ G r x n , 298 ∘ = Δ G f ∘ ( SO 3 ) − Δ G f ∘ ( SO 2 ) − 0.5 Δ G f ∘ ( O 2 ) \Delta G_{rxn,298}^\circ = \Delta G_{f}^\circ(\text{SO}_3) - \Delta G_{f}^\circ(\text{SO}_2) - 0.5 \Delta G_{f}^\circ(\text{O}_2) Δ G r x n , 298 ∘ = Δ G f ∘ ( SO 3 ) − Δ G f ∘ ( SO 2 ) − 0.5Δ G f ∘ ( O 2 ) Δ G r x n , 298 ∘ = − 371.06 − ( − 300.19 ) − 0.5 ( 0 ) = − 70.87 kJ/mol = − 70 , 870 J/mol \Delta G_{rxn,298}^\circ = -371.06 - (-300.19) - 0.5(0) = \mathbf{-70.87\text{ kJ/mol}} = -70,870\text{ J/mol} Δ G r x n , 298 ∘ = − 371.06 − ( − 300.19 ) − 0.5 ( 0 ) = − 70.87 kJ/mol = − 70 , 870 J/mol
(The negative Δ H ∘ \Delta H^\circ Δ H ∘ indicates a strongly exothermic reaction; the negative Δ G ∘ \Delta G^\circ Δ G ∘ indicates strong thermodynamic spontaneity at ambient temperature).
Step 2: Equilibrium Constant at 298.15 K 298.15\text{ K} 298.15 K K a ( 298.15 K ) = exp ( − Δ G r x n , 298 ∘ R T 0 ) = exp ( − − 70 , 870 J/mol ( 8.31447 J/(mol ⋅ K) ) ( 298.15 K ) ) K_a(298.15\text{ K}) = \exp\left( -\frac{\Delta G_{rxn,298}^\circ}{R T_0} \right) = \exp\left( -\frac{-70,870\text{ J/mol}}{(8.31447\text{ J/(mol}\cdot\text{K)})(298.15\text{ K})} \right) K a ( 298.15 K ) = exp ( − R T 0 Δ G r x n , 298 ∘ ) = exp ( − ( 8.31447 J/(mol ⋅ K) ) ( 298.15 K ) − 70 , 870 J/mol ) K a ( 298.15 K ) = exp ( 70 , 870 2478.96 ) = exp ( 28.5886 ) = 2.605 × 10 12 K_a(298.15\text{ K}) = \exp\left( \frac{70,870}{2478.96} \right) = \exp(28.5886) = \mathbf{2.605 \times 10^{12}} K a ( 298.15 K ) = exp ( 2478.96 70 , 870 ) = exp ( 28.5886 ) = 2.605 × 1 0 12
At room temperature, equilibrium lies overwhelmingly on the product side ( K a > 10 12 K_a > 10^{12} K a > 1 0 12 ), but the reaction is kinetically inert without high temperatures to activate the catalyst.
Step 3: Equilibrium Constant at T = 700.0 K T = 700.0\text{ K} T = 700.0 K via van 't Hoff Equation
Apply the integrated van 't Hoff equation: ln ( K a ( T ) K a ( T 0 ) ) = − Δ H r x n ∘ R ( 1 T − 1 T 0 ) \ln\left( \frac{K_a(T)}{K_a(T_0)} \right) = -\frac{\Delta H_{rxn}^\circ}{R} \left( \frac{1}{T} - \frac{1}{T_0} \right) ln ( K a ( T 0 ) K a ( T ) ) = − R Δ H r x n ∘ ( T 1 − T 0 1 ) 1 T − 1 T 0 = 1 700.0 K − 1 298.15 K = 0.00142857 − 0.00335402 = − 0.00192545 K − 1 \frac{1}{T} - \frac{1}{T_0} = \frac{1}{700.0\text{ K}} - \frac{1}{298.15\text{ K}} = 0.00142857 - 0.00335402 = -0.00192545\text{ K}^{-1} T 1 − T 0 1 = 700.0 K 1 − 298.15 K 1 = 0.00142857 − 0.00335402 = − 0.00192545 K − 1 ln ( K a ( 700 ) K a ( 298 ) ) = − ( − 98 , 890 8.31447 ) × ( − 0.00192545 ) = ( 11 , 893.72 ) × ( − 0.00192545 ) = − 22.9006 \ln\left( \frac{K_a(700)}{K_a(298)} \right) = -\left( \frac{-98,890}{8.31447} \right) \times (-0.00192545) = (11,893.72) \times (-0.00192545) = \mathbf{-22.9006} ln ( K a ( 298 ) K a ( 700 ) ) = − ( 8.31447 − 98 , 890 ) × ( − 0.00192545 ) = ( 11 , 893.72 ) × ( − 0.00192545 ) = − 22.9006 K a ( 700.0 K ) = K a ( 298.15 K ) × exp ( − 22.9006 ) = ( 2.605 × 10 12 ) × ( 1.1335 × 10 − 10 ) = 295.3 K_a(700.0\text{ K}) = K_a(298.15\text{ K}) \times \exp(-22.9006) = (2.605 \times 10^{12}) \times (1.1335 \times 10^{-10}) = \mathbf{295.3} K a ( 700.0 K ) = K a ( 298.15 K ) × exp ( − 22.9006 ) = ( 2.605 × 1 0 12 ) × ( 1.1335 × 1 0 − 10 ) = 295.3
Raising the temperature from 298 K 298\text{ K} 298 K to 700 K 700\text{ K} 700 K drops the equilibrium constant by 10 orders of magnitude (from 2.6 × 10 12 2.6 \times 10^{12} 2.6 × 1 0 12 down to 295.3 295.3 295.3 ) due to the exothermic heat of reaction.
Step 4: Stoichiometry and Equilibrium Expression
Stoichiometric coefficients: ν SO 2 = − 1 , ν O 2 = − 0.5 , ν SO 3 = + 1 , ν N 2 = 0 \nu_{\text{SO}_2} = -1, \quad \nu_{\text{O}_2} = -0.5, \quad \nu_{\text{SO}_3} = +1, \quad \nu_{\text{N}_2} = 0 ν SO 2 = − 1 , ν O 2 = − 0.5 , ν SO 3 = + 1 , ν N 2 = 0 Δ ν = ∑ ν i = − 1 − 0.5 + 1 = − 0.5 \Delta \nu = \sum \nu_i = -1 - 0.5 + 1 = \mathbf{-0.5} Δ ν = ∑ ν i = − 1 − 0.5 + 1 = − 0.5
Gas-phase equilibrium formulation ( P ∘ = 1.00 bar P^\circ = 1.00\text{ bar} P ∘ = 1.00 bar ): K a = ( P P ∘ ) Δ ν K y = ( P P ∘ ) − 0.5 y SO 3 y SO 2 ⋅ y O 2 0.5 K_a = \left( \frac{P}{P^\circ} \right)^{\Delta \nu} K_y = \left( \frac{P}{P^\circ} \right)^{-0.5} \frac{y_{\text{SO}_3}}{y_{\text{SO}_2} \cdot y_{\text{O}_2}^{0.5}} K a = ( P ∘ P ) Δ ν K y = ( P ∘ P ) − 0.5 y SO 2 ⋅ y O 2 0.5 y SO 3
Step 5: Stoichiometric Table and Conversion Calculation
Let X X X be the fractional conversion of SO 2 \text{SO}_2 SO 2 (extent ξ = 1.00 X \xi = 1.00 X ξ = 1.00 X ):
Species Feed Moles ( n i , 0 n_{i,0} n i , 0 ) Change Equilibrium Moles ( n i n_i n i ) Mole Fraction ( y i y_i y i )
SO 2 \text{SO}_2 SO 2 1.00 1.00 1.00 − X -X − X 1.00 − X 1.00 - X 1.00 − X ( 1.00 − X ) / n t o t (1.00 - X) / n_{tot} ( 1.00 − X ) / n t o t
O 2 \text{O}_2 O 2 0.80 0.80 0.80 − 0.5 X -0.5X − 0.5 X 0.80 − 0.5 X 0.80 - 0.5X 0.80 − 0.5 X ( 0.80 − 0.5 X ) / n t o t (0.80 - 0.5X) / n_{tot} ( 0.80 − 0.5 X ) / n t o t
- SO 3 \text{SO}_3 SO 3 0.00 0.00 0.00 + X +X + X X X X X / n t o t X / n_{tot} X / n t o t
- N 2 \text{N}_2 N 2 (inert) 4.00 4.00 4.00 0 0 0 4.00 4.00 4.00 4.00 / n t o t 4.00 / n_{tot} 4.00/ n t o t
TOTAL ( n t o t n_{tot} n t o t ) 5.80 5.80 5.80 − 0.5 X -0.5X − 0.5 X 5.80 − 0.5 X 5.80 - 0.5X 5.80 − 0.5 X 1.000 1.000 1.000
Substitute mole fractions into K y K_y K y : K y = y SO 3 y SO 2 y O 2 0.5 = X n t o t ( 1.00 − X n t o t ) ( 0.80 − 0.5 X n t o t ) 0.5 = X 1.00 − X n t o t 0.80 − 0.5 X K_y = \frac{y_{\text{SO}_3}}{y_{\text{SO}_2} y_{\text{O}_2}^{0.5}} = \frac{\frac{X}{n_{tot}}}{\left(\frac{1.00 - X}{n_{tot}}\right) \left(\frac{0.80 - 0.5X}{n_{tot}}\right)^{0.5}} = \frac{X}{1.00 - X} \sqrt{\frac{n_{tot}}{0.80 - 0.5X}} K y = y SO 2 y O 2 0.5 y SO 3 = ( n t o t 1.00 − X ) ( n t o t 0.80 − 0.5 X ) 0.5 n t o t X = 1.00 − X X 0.80 − 0.5 X n t o t K y = X 1.00 − X 5.80 − 0.5 X 0.80 − 0.5 X K_y = \frac{X}{1.00 - X} \sqrt{\frac{5.80 - 0.5X}{0.80 - 0.5X}} K y = 1.00 − X X 0.80 − 0.5 X 5.80 − 0.5 X
Relating K y K_y K y to K a K_a K a at P = 2.00 bar P = 2.00\text{ bar} P = 2.00 bar : K y = K a ( P P ∘ ) − Δ ν = 295.3 × ( 2.00 ) − ( − 0.5 ) = 295.3 × 2.00 = 295.3 × 1.4142 = 417.6 K_y = K_a \left( \frac{P}{P^\circ} \right)^{-\Delta \nu} = 295.3 \times (2.00)^{-(-0.5)} = 295.3 \times \sqrt{2.00} = 295.3 \times 1.4142 = \mathbf{417.6} K y = K a ( P ∘ P ) − Δ ν = 295.3 × ( 2.00 ) − ( − 0.5 ) = 295.3 × 2.00 = 295.3 × 1.4142 = 417.6
Equating expressions: X 1.00 − X 5.80 − 0.5 X 0.80 − 0.5 X = 417.6 \frac{X}{1.00 - X} \sqrt{\frac{5.80 - 0.5X}{0.80 - 0.5X}} = 417.6 1.00 − X X 0.80 − 0.5 X 5.80 − 0.5 X = 417.6
Solving for X X X by trial and error / successive approximation:
For X = 0.980 X = 0.980 X = 0.980 : 0.980 0.020 5.80 − 0.490 0.80 − 0.490 = 49.0 × 5.310 0.310 = 49.0 × 17.129 = 49.0 × 4.1387 = 202.8 ( < 417.6 ) \frac{0.980}{0.020} \sqrt{\frac{5.80 - 0.490}{0.80 - 0.490}} = 49.0 \times \sqrt{\frac{5.310}{0.310}} = 49.0 \times \sqrt{17.129} = 49.0 \times 4.1387 = 202.8 \quad (< 417.6) 0.020 0.980 0.80 − 0.490 5.80 − 0.490 = 49.0 × 0.310 5.310 = 49.0 × 17.129 = 49.0 × 4.1387 = 202.8 ( < 417.6 )
For X = 0.990 X = 0.990 X = 0.990 : 0.990 0.010 5.80 − 0.495 0.80 − 0.495 = 99.0 × 5.305 0.305 = 99.0 × 17.393 = 99.0 × 4.1705 = 412.9 ≈ 417.6 \frac{0.990}{0.010} \sqrt{\frac{5.80 - 0.495}{0.80 - 0.495}} = 99.0 \times \sqrt{\frac{5.305}{0.305}} = 99.0 \times \sqrt{17.393} = 99.0 \times 4.1705 = 412.9 \approx 417.6 0.010 0.990 0.80 − 0.495 5.80 − 0.495 = 99.0 × 0.305 5.305 = 99.0 × 17.393 = 99.0 × 4.1705 = 412.9 ≈ 417.6
For X = 0.9905 X = 0.9905 X = 0.9905 : 0.9905 0.0095 × 4.172 = 104.26 × 4.172 = 435.0 ( > 417.6 ) \frac{0.9905}{0.0095} \times 4.172 = 104.26 \times 4.172 = 435.0 \quad (> 417.6) 0.0095 0.9905 × 4.172 = 104.26 × 4.172 = 435.0 ( > 417.6 )
Interpolating yields the equilibrium conversion: X e q = 0.990 ( 99.0 % ) X_{eq} = \mathbf{0.990} \quad (\mathbf{99.0\%}) X e q = 0.990 ( 99.0% )
At 700 K 700\text{ K} 700 K and 2 bar 2\text{ bar} 2 bar , thermodynamic equilibrium permits up to 99.0 % 99.0\% 99.0% conversion of sulfur dioxide to sulfur trioxide.
- 9. Critical PE Exam Traps & Pitfalls
- Trap 1: Believing that System Pressure Changes the Equilibrium Constant ( K a K_a K a )
This is among the most heavily tested conceptual distractors on the NCEES PE Chemical Exam. Pressure NEVER changes K a K_a K a ! K a K_a K a is solely a function of temperature ( K a = exp [ − Δ G ∘ / ( R T ) ] K_a = \exp[-\Delta G^\circ / (R T)] K a = exp [ − Δ G ∘ / ( RT )] ). Pressure changes the equilibrium composition ( K y K_y K y ) through the ( P / P ∘ ) − Δ ν (P/P^\circ)^{-\Delta \nu} ( P / P ∘ ) − Δ ν factor, but K a K_a K a remains strictly constant.
Trap 2: Inverting Signs in the van 't Hoff Equation
Notice the negative sign in ln ( K 2 / K 1 ) = − ( Δ H ∘ / R ) ( 1 / T 2 − 1 / T 1 ) \ln(K_2/K_1) = -(\Delta H^\circ / R) (1/T_2 - 1/T_1) ln ( K 2 / K 1 ) = − ( Δ H ∘ / R ) ( 1/ T 2 − 1/ T 1 ) . For an exothermic reaction ( Δ H ∘ < 0 \Delta H^\circ < 0 Δ H ∘ < 0 ), − Δ H ∘ -\Delta H^\circ − Δ H ∘ becomes positive. When heating ( T 2 > T 1 T_2 > T_1 T 2 > T 1 ), ( 1 / T 2 − 1 / T 1 ) (1/T_2 - 1/T_1) ( 1/ T 2 − 1/ T 1 ) is negative. A positive multiplied by a negative yields a negative, meaning ln ( K 2 / K 1 ) < 0 ⟹ K 2 < K 1 \ln(K_2/K_1) < 0 \implies K_2 < K_1 ln ( K 2 / K 1 ) < 0 ⟹ K 2 < K 1 . Verify this physical consistency: heating an exothermic reaction must reduce K K K .
Trap 3: Forgetting Inert Moles in the Total Mole Count ( n t o t n_{tot} n t o t )
When setting up mole fractions ( y i = n i / n t o t y_i = n_i / n_{tot} y i = n i / n t o t ), inerts (such as nitrogen in air, or steam) do not react, but they must be included in n t o t n_{tot} n t o t . Omitting inerts from the denominator artificially inflates the reactant partial pressures, producing severe calculation errors.
Trap 4: Expecting a Catalyst to Increase Thermodynamic Equilibrium Conversion
If an exam question asks "Which modification will increase the equilibrium conversion of an endothermic reaction?" and includes "Adding an active catalyst" as an option, do not pick it! Catalysts only increase the rate at which equilibrium is reached. They alter neither Δ G r x n ∘ \Delta G_{rxn}^\circ Δ G r x n ∘ nor K a K_a K a nor equilibrium conversion.