Study guide

7.1 Pure Component Vapor Pressure and Phase Equilibria

PE Chemical Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the PE Chemical Exam How to Use This Guide and the NCEES Handbook

2 Chapter 1: Material Balances & Flowsheet Calculations

1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations

3 Chapter 2: Energy Balances & Thermochemistry

2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances

4 Chapter 3: Fluid Statics & Incompressible Pipe Flow

3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations

5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up

6 Chapter 5: Thermodynamic Laws & Fundamental Relations

5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations

7 Chapter 6: Real Gases & Equations of State

6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions

8 Chapter 7: Phase & Chemical Reaction Equilibria

7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation

9 Chapter 8: Heat Transfer Mechanisms & Conduction

8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange

10 Chapter 9: Heat Exchanger Design & Phase Change

9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances

11 Chapter 10: Mass Transfer Fundamentals & Diffusion

10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

12 Chapter 11: Distillation Operations

11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components

13 Chapter 12: Rate-Controlled & Equilibrium Separations

12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations

14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors

13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations

15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis

14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models

16 Chapter 15: Physical & Transport Properties of Fluids

15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles

17 Chapter 16: Materials of Construction & Corrosion

16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention

18 Chapter 17: Process Safety & Pressure Relief Systems

17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment

19 Chapter 18: Process Control & Engineering Economics

18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems

20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance

19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation

21 Chapter 20: Plant Operation, Reliability & Continuous Improvement

20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting

7.1 Pure Component Vapor Pressure and Phase Equilibria

Key Takeaways Explain This Topic AI

The Gibbs Phase Rule (F = C - P + 2) dictates the degrees of freedom for non-reacting equilibrium systems; for a pure single-component fluid (C = 1), specifying pressure uniquely fixes the saturation temperature during two-phase coexistence (P = 2 -> F = 1).

The Clapeyron equation [dP_sat/dT = Delta H_vap / (T * Delta v_vap)] is an exact thermodynamic relationship governing phase boundaries; introducing ideal gas vapor behavior and neglecting liquid volume yields the Clausius-Clapeyron equation [d(ln P_sat)/dT = Delta H_vap / (R * T^2)].

The Antoine equation [log10(P_sat) = A - B/(T + C) or ln(P_sat) = A - B/(T + C)] empirically models vapor pressure curvature across moderate temperature intervals by incorporating an effective temperature adjustment parameter C.

On the NCEES PE Chemical Exam, unit consistency in Antoine equation evaluations is paramount: mixing Celsius with Kelvin, base-10 with natural logarithms, or mmHg with bar or kPa generates catastrophic numerical errors.

Cox charts linearize vapor pressure data over extended temperature spans by plotting log(P_sat) against an empirical temperature scale calibrated to water, enabling rapid graphical interpolation and safe extrapolation toward the critical point.

Last updated: September 2026

7.1 Pure Component Vapor Pressure and Phase Equilibria

Phase equilibria and vapor pressure estimation form the cornerstone of separation design, relief system sizing, and process vessel specification on the NCEES PE Chemical Exam . When a pure liquid boils inside a reboiler, flashes across an expansion valve, or evaporates from a storage tank, the system establishes a dynamic balance governed by thermodynamic potential gradients. Understanding how temperature and pressure dictate phase transitions enables chemical engineers to accurately compute operating conditions, prevent cavitation, and size distillation columns.

1. Fundamental Thermodynamic Criteria of Phase Equilibrium

Consider an isolated, multi-phase, pure-component system containing π \pi π distinct phases (e.g., solid, liquid, and vapor) labeled α , β , … , π \alpha, \beta, \dots, \pi α , β , … , π . From the Second Law of Thermodynamics , an isolated system reaches equilibrium when its total entropy is maximized. At specified temperature ( T T T ) and pressure ( P P P ), this condition corresponds to minimizing the total Gibbs free energy ( d G T , P = 0 dG_{T,P} = 0 d G T , P ​ = 0 ).

For a closed, heterogeneous system at uniform T T T and P P P , transferring an infinitesimal quantity of moles d n i dn_i d n i ​ from phase α \alpha α to phase β \beta β produces a change in total Gibbs energy: d G = μ i α ( − d n i ) + μ i β ( d n i ) = ( μ i β − μ i α ) d n i dG = \mu_i^\alpha (-dn_i) + \mu_i^\beta (dn_i) = \left( \mu_i^\beta - \mu_i^\alpha \right) dn_i d G = μ i α ​ ( − d n i ​ ) + μ i β ​ ( d n i ​ ) = ( μ i β ​ − μ i α ​ ) d n i ​

Where μ i \mu_i μ i ​ is the chemical potential of species i i i , defined as the partial molar Gibbs free energy: μ i ≡ ( ∂ G ∂ n i ) T , P , n j ≠ i \mu_i \equiv \left( \frac{\partial G}{\partial n_i} \right)_{T, P, n_{j \ne i}} μ i ​ ≡ ( ∂ n i ​ ∂ G ​ ) T , P , n j  = i ​ ​

At thermodynamic equilibrium, d G = 0 dG = 0 d G = 0 for any arbitrary, reversible mass transfer d n i dn_i d n i ​ . Therefore, phase coexistence demands three simultaneous conditions:

Thermal Equilibrium : Uniform temperature across all phases. T α = T β = ⋯ = T π T^\alpha = T^\beta = \dots = T^\pi T α = T β = ⋯ = T π

Mechanical Equilibrium : Uniform pressure across all phases (in the absence of interfacial surface tension or hydrostatic heads). P α = P β = ⋯ = P π P^\alpha = P^\beta = \dots = P^\pi P α = P β = ⋯ = P π

Chemical / Phase Equilibrium : Uniform chemical potential (or fugacity) of each component across all phases. μ i α = μ i β = ⋯ = μ i π ⟺ f i α = f i β = ⋯ = f i π \mu_i^\alpha = \mu_i^\beta = \dots = \mu_i^\pi \iff f_i^\alpha = f_i^\beta = \dots = f_i^\pi μ i α ​ = μ i β ​ = ⋯ = μ i π ​ ⟺ f i α ​ = f i β ​ = ⋯ = f i π ​

If μ i α > μ i β \mu_i^\alpha > \mu_i^\beta μ i α ​ > μ i β ​ , mass spontaneously transfers from phase α \alpha α to phase β \beta β until the chemical potentials equalize. For a pure substance ( C = 1 C = 1 C = 1 ), the chemical potential equals the molar Gibbs free energy of that phase ( μ = g \mu = g μ = g ).

2. The Gibbs Phase Rule

Josiah Willard Gibbs established the Gibbs Phase Rule , which defines the number of independent intensive variables (degrees of freedom, F F F ) that must be specified to completely fix the thermodynamic state of an equilibrium system.

  • Mathematical Formulation
  • For a non-reacting system: F = C − P + 2 F = C - P + 2 F = C − P + 2

Where:

F F F = degrees of freedom (variance) of the system.

C C C = number of non-reacting chemical components.

P P P = number of phases coexisting at equilibrium.

2 2 2 = represents the two intensive state variables: temperature ( T T T ) and pressure ( P P P ).

If the system involves r r r independent reversible chemical reactions and s s s special stoichiometric constraints (such as equimolar production from an initial charge), the rule generalizes to: F = ( C − r − s ) − P + 2 F = (C - r - s) - P + 2 F = ( C − r − s ) − P + 2

Degrees of Freedom for Pure Fluids ( C = 1 C = 1 C = 1 )

Single Phase ( P = 1 P = 1 P = 1 : Superheated Vapor, Subcooled Liquid, or Supercritical Fluid) : F = 1 − 1 + 2 = 2 F = 1 - 1 + 2 = 2 F = 1 − 1 + 2 = 2 Two intensive properties must be specified (e.g., both T T T and P P P ) to locate the thermodynamic state and determine properties such as density, enthalpy, and entropy.

Two Coexisting Phases ( P = 2 P = 2 P = 2 : Saturated Liquid + Saturated Vapor) : F = 1 − 2 + 2 = 1 F = 1 - 2 + 2 = 1 F = 1 − 2 + 2 = 1 Only one intensive variable can be independently specified. Specifying temperature T T T uniquely fixes the vapor pressure P s a t ( T ) P^{sat}(T) P s a t ( T ) . Conversely, specifying system pressure P P P uniquely fixes the saturation boiling temperature T s a t ( P ) T^{sat}(P) T s a t ( P ) . A chemical process engineer cannot independently control both temperature and pressure in an equilibrium reboiler containing pure liquid and vapor.

Three Coexisting Phases ( P = 3 P = 3 P = 3 : Solid + Liquid + Vapor at the Triple Point) : F = 1 − 3 + 2 = 0 F = 1 - 3 + 2 = 0 F = 1 − 3 + 2 = 0 The system is invariant . The triple point exists at a single, unique temperature and pressure (for water, T t p = 0.01 ∘ C = 273.16 K T_{tp} = 0.01^\circ\text{C} = 273.16\text{ K} T tp ​ = 0.0 1 ∘ C = 273.16 K and P t p = 0.6117 kPa = 4.587 mmHg P_{tp} = 0.6117\text{ kPa} = 4.587\text{ mmHg} P tp ​ = 0.6117 kPa = 4.587 mmHg ). Neither T T T nor P P P can be altered without causing at least one phase to completely disappear.

Critical Point :

At the critical point ( T c , P c T_c, P_c T c ​ , P c ​ ), the meniscus between liquid and vapor vanishes, and all intensive properties of both phases merge into a single supercritical fluid. This boundary point is invariant ( F = 0 F = 0 F = 0 ) for a pure component.

Comparison Table: Gibbs Phase Rule Applications in Process Engineering

System Description Components ( C C C ) Phases ( P P P ) Degrees of Freedom ( F F F ) Practical Engineering Consequence

Superheated Steam in Piping 1 1 (Vapor) 2 Must measure both T T T and P P P to calculate steam density and enthalpy.

Boiler Drum Steam-Water Mixture 1 2 (Liquid + Vapor) 1 Pressure transmitter uniquely determines water temperature; redundant T T T probe acts as check.

Pure Water Triple Point Cell 1 3 (Solid + Liquid + Vapor) 0 Used as an international temperature calibration standard ( 273.16 K 273.16\text{ K} 273.16 K ).

Binary Distillation Column Tray 2 2 (Liquid + Vapor) 2 Specifying column pressure P P P leaves 1 degree of freedom: tray temperature fixes composition.

Immiscible Liquid Decanter (Water + Hydrocarbon) 2 3 (2 Liquid + 1 Vapor) 1 Fixing column pressure P P P fixes three-phase boiling temperature and all equilibrium compositions.

3. The Clapeyron and Clausius-Clapeyron Equations

Along any phase coexistence boundary line on a P − T P-T P − T diagram, the molar Gibbs free energy of the two coexisting phases must remain equal ( g α = g β g^\alpha = g^\beta g α = g β ). Moving an infinitesimal distance d T dT d T and d P dP d P along this equilibrium curve requires: d g α = d g β dg^\alpha = dg^\beta d g α = d g β

Applying the fundamental property relation d g = − s d T + v d P dg = -s dT + v dP d g = − s d T + v d P : − s α d T + v α d P = − s β d T + v β d P -s^\alpha dT + v^\alpha dP = -s^\beta dT + v^\beta dP − s α d T + v α d P = − s β d T + v β d P

Rearranging terms: ( v β − v α ) d P = ( s β − s α ) d T \left( v^\beta - v^\alpha \right) dP = \left( s^\beta - s^\alpha \right) dT ( v β − v α ) d P = ( s β − s α ) d T

Because the phase transition is reversible at constant T T T and P P P , the molar entropy of phase change is Δ s = s β − s α = Δ h / T \Delta s = s^\beta - s^\alpha = \Delta h / T Δ s = s β − s α = Δ h / T . Substituting this yields the Clapeyron Equation : d P s a t d T = Δ h v a p T ( v V − v L ) = Δ H v a p T Δ v v a p \frac{dP^{sat}}{dT} = \frac{\Delta h_{vap}}{T \left( v^V - v^L \right)} = \frac{\Delta H_{vap}}{T \Delta v_{vap}} d T d P s a t ​ = T ( v V − v L ) Δ h v a p ​ ​ = T Δ v v a p ​ Δ H v a p ​ ​

The Clapeyron equation is thermodynamically exact for any first-order phase transition (solid-liquid, liquid-vapor, solid-vapor) across all pressures up to the critical point.

The Clausius-Clapeyron Approximation

For vapor-liquid equilibria at low to moderate pressures (typically P < 5 bar P < 5\text{ bar} P < 5 bar or T < 0.75 T c T < 0.75 T_c T < 0.75 T c ​ ), Rudolf Clausius introduced two simplifying assumptions:

Negligible Liquid Molar Volume : The molar volume of the liquid phase is negligible compared to the molar volume of the vapor phase ( v V ≫ v L ⟹ Δ v v a p = v V − v L ≈ v V v^V \gg v^L \implies \Delta v_{vap} = v^V - v^L \approx v^V v V ≫ v L ⟹ Δ v v a p ​ = v V − v L ≈ v V ).

Ideal Gas Vapor Behavior : The vapor phase behaves as an ideal gas ( v V = R T / P s a t v^V = R T / P^{sat} v V = RT / P s a t ).

Constant Latent Heat : The enthalpy of vaporization ( Δ H v a p \Delta H_{vap} Δ H v a p ​ ) remains constant over the temperature span of interest.

Substituting v V = R T / P s a t v^V = R T / P^{sat} v V = RT / P s a t into the Clapeyron equation: d P s a t d T = Δ H v a p T ( R T P s a t ) = P s a t Δ H v a p R T 2 \frac{dP^{sat}}{dT} = \frac{\Delta H_{vap}}{T \left( \frac{R T}{P^{sat}} \right)} = \frac{P^{sat} \Delta H_{vap}}{R T^2} d T d P s a t ​ = T ( P s a t RT ​ ) Δ H v a p ​ ​ = R T 2 P s a t Δ H v a p ​ ​

Dividing through by P s a t P^{sat} P s a t yields the differential Clausius-Clapeyron Equation : 1 P s a t d P s a t d T = d ln ⁡ P s a t d T = Δ H v a p R T 2 \frac{1}{P^{sat}} \frac{dP^{sat}}{dT} = \frac{d\ln P^{sat}}{dT} = \frac{\Delta H_{vap}}{R T^2} P s a t 1 ​ d T d P s a t ​ = d T d ln P s a t ​ = R T 2 Δ H v a p ​ ​

Separating variables and integrating between state 1 ( T 1 , P 1 s a t T_1, P_1^{sat} T 1 ​ , P 1 s a t ​ ) and state 2 ( T 2 , P 2 s a t T_2, P_2^{sat} T 2 ​ , P 2 s a t ​ ): ∫ P 1 s a t P 2 s a t d ln ⁡ P s a t = Δ H v a p R ∫ T 1 T 2 d T T 2 \int_{P_1^{sat}}^{P_2^{sat}} d\ln P^{sat} = \frac{\Delta H_{vap}}{R} \int_{T_1}^{T_2} \frac{dT}{T^2} ∫ P 1 s a t ​ P 2 s a t ​ ​ d ln P s a t = R Δ H v a p ​ ​ ∫ T 1 ​ T 2 ​ ​ T 2 d T ​ ln ⁡ ( P 2 s a t P 1 s a t ) = − Δ H v a p R ( 1 T 2 − 1 T 1 ) = Δ H v a p R ( T 2 − T 1 T 1 T 2 ) \ln\left( \frac{P_2^{sat}}{P_1^{sat}} \right) = -\frac{\Delta H_{vap}}{R} \left( \frac{1}{T_2} - \frac{1}{T_1} \right) = \frac{\Delta H_{vap}}{R} \left( \frac{T_2 - T_1}{T_1 T_2} \right) ln ( P 1 s a t ​ P 2 s a t ​ ​ ) = − R Δ H v a p ​ ​ ( T 2 ​ 1 ​ − T 1 ​ 1 ​ ) = R Δ H v a p ​ ​ ( T 1 ​ T 2 ​ T 2 ​ − T 1 ​ ​ )

Linear Form and Graphical Interpretation

The indefinite integral produces a linear relationship: ln ⁡ P s a t = − Δ H v a p R ( 1 T ) + C c o n s t \ln P^{sat} = -\frac{\Delta H_{vap}}{R} \left( \frac{1}{T} \right) + C_{const} ln P s a t = − R Δ H v a p ​ ​ ( T 1 ​ ) + C co n s t ​

A plot of ln ⁡ P s a t \ln P^{sat} ln P s a t versus 1 / T 1/T 1/ T (with temperature in absolute units, K \text{K} K ) yields a straight line with a negative slope equal to − Δ H v a p / R -\Delta H_{vap} / R − Δ H v a p ​ / R .

The y-intercept represents the integration constant C c o n s t C_{const} C co n s t ​ .

This equation provides a rapid two-point estimation method on the PE exam when only the normal boiling point ( T b T_b T b ​ at 1.0 atm 1.0\text{ atm} 1.0 atm ) and latent heat of vaporization are given.

4. Empirical Vapor Pressure Formulations: The Antoine Equation

While the Clausius-Clapeyron equation provides fundamental insight, real vapor pressure curves plotted as ln ⁡ P s a t \ln P^{sat} ln P s a t vs 1 / T 1/T 1/ T exhibit distinct curvature over wide temperature ranges. This curvature arises because Δ H v a p \Delta H_{vap} Δ H v a p ​ decreases monotonically with increasing temperature (reaching zero at the critical point, T c T_c T c ​ ), and real vapor deviations ( Z < 1 Z < 1 Z < 1 ) become pronounced at higher pressures.

To capture this curvature empirically without complex multi-parameter equations of state, Louis Charles Antoine (1888) introduced an effective temperature offset parameter ( C C C ).

Antoine Equation Formulations

On the NCEES PE Chemical Exam and in engineering reference literature, the Antoine equation appears in two common algebraic forms:

Form 1: Base-10 Logarithm (Common in Perry's Chemical Engineers' Handbook) log ⁡ 10 P s a t = A − B T + C \log_{10} P^{sat} = A - \frac{B}{T + C} lo g 10 ​ P s a t = A − T + C B ​

Typical units: P s a t P^{sat} P s a t in mmHg \text{mmHg} mmHg (or bar \text{bar} bar ), and T T T in ∘ C ^\circ\text{C} ∘ C .

Solved explicitly for temperature (bubble/dew point calculation): T = B A − log ⁡ 10 P s a t − C T = \frac{B}{A - \log_{10} P^{sat}} - C T = A − lo g 10 ​ P s a t B ​ − C

Form 2: Natural Logarithm (Common in NCEES Reference Handbook & NIST) ln ⁡ P s a t = A − B T + C \ln P^{sat} = A - \frac{B}{T + C} ln P s a t = A − T + C B ​

Typical units: P s a t P^{sat} P s a t in kPa \text{kPa} kPa (or bar \text{bar} bar ), and T T T in K \text{K} K (or ∘ C ^\circ\text{C} ∘ C ).

Solved explicitly for temperature: T = B A − ln ⁡ P s a t − C T = \frac{B}{A - \ln P^{sat}} - C T = A − ln P s a t B ​ − C

Extended Vapor Pressure Models (DIPPR 101 & Wagner)

For high-accuracy applications spanning from the triple point to the critical point, process simulators (Aspen, HYSYS) employ the Wagner Equation : ln ⁡ P r s a t = A τ + B τ 1.5 + C τ 3 + D τ 6 1 − τ \ln P_r^{sat} = \frac{A \tau + B \tau^{1.5} + C \tau^3 + D \tau^6}{1 - \tau} ln P r s a t ​ = 1 − τ A τ + B τ 1.5 + C τ 3 + D τ 6 ​

Where reduced vapor pressure is P r s a t = P s a t / P c P_r^{sat} = P^{sat}/P_c P r s a t ​ = P s a t / P c ​ , dimensionless temperature departure is τ = 1 − T r = 1 − ( T / T c ) \tau = 1 - T_r = 1 - (T/T_c) τ = 1 − T r ​ = 1 − ( T / T c ​ ) , and A , B , C , D A, B, C, D A , B , C , D are substance-specific constants. The Wagner equation correctly models the infinite slope of Δ H v a p \Delta H_{vap} Δ H v a p ​ as T → T c T \to T_c T → T c ​ and avoids unphysical behavior outside the Antoine temperature range.

5. Cox Charts and Reference Fluid Methods

Before digital computers, chemical engineers utilized graphical Cox Charts to linearize vapor pressure curves across vast temperature spans (from sub-ambient to supercritical conditions).

Operating Principle

Edwin R. Cox (1923) observed that if log ⁡ 10 P s a t \log_{10} P^{sat} lo g 10 ​ P s a t is plotted against a special, non-linear temperature scale calibrated so that the vapor pressure of a reference substance (usually water) forms a perfectly straight line, the vapor pressure curves of almost all other hydrocarbons and organic liquids also become straight lines: log ⁡ 10 P s a t = A − B T ∗ \log_{10} P^{sat} = A - \frac{B}{T^*} lo g 10 ​ P s a t = A − T ∗ B ​

Where T ∗ T^* T ∗ is the transformed reference temperature function.

Key Practical Properties of Cox Charts

Infinite Convergence Point : For homologous series (e.g., straight-chain paraffinic alkanes: methane through n-decane), the straight lines converge toward a single common focal point at high temperature and pressure.

Extrapolation Accuracy : Because the lines are straight on Cox coordinates, drawing a line through just two reliable data points (such as the normal boiling point and room-temperature vapor pressure) enables accurate extrapolation toward elevated pressures without significant error.

6. Summary Comparison: Vapor Pressure Estimation Models

Method Mathematical Form Input Parameters Required Temperature & Pressure Range Error on PE Exam / Limitations

Clausius-Clapeyron ln ⁡ ( P 2 / P 1 ) = − Δ H v a p R ( 1 T 2 − 1 T 1 ) \ln(P_2/P_1) = -\frac{\Delta H_{vap}}{R}\left(\frac{1}{T_2}-\frac{1}{T_1}\right) ln ( P 2 ​ / P 1 ​ ) = − R Δ H v a p ​ ​ ( T 2 ​ 1 ​ − T 1 ​ 1 ​ ) Normal boiling point ( T b T_b T b ​ ), Δ H v a p \Delta H_{vap} Δ H v a p ​ Narrow temperature range ( < 30 ∘ C < 30^\circ\text{C} < 3 0 ∘ C span), P < 2 bar P < 2\text{ bar} P < 2 bar 5 − 15 % 5-15\% 5 − 15% error over wide spans; assumes constant Δ H v a p \Delta H_{vap} Δ H v a p ​ and ideal gas.

Antoine Equation log ⁡ 10 P s a t = A − B T + C \log_{10} P^{sat} = A - \frac{B}{T + C} lo g 10 ​ P s a t = A − T + C B ​ Three empirical parameters ( A , B , C A, B, C A , B , C ) Subcritical range ( T m i n ≤ T ≤ T m a x T_{min} \le T \le T_{max} T min ​ ≤ T ≤ T ma x ​ listed in handbook) < 1 − 2 % < 1-2\% < 1 − 2% inside tabulated range; severe divergence if extrapolated outside range.

Cox Chart log ⁡ 10 P s a t = A − B / T ∗ \log_{10} P^{sat} = A - B/T^* lo g 10 ​ P s a t = A − B / T ∗ Reference fluid curve (water) + 2 points Broad subcritical range up to T c T_c T c ​ Graphical read errors ( 2 − 4 % 2-4\% 2 − 4% ); excellent for rapid homologous series screening.

Wagner Equation ln ⁡ P r = A τ + B τ 1.5 + C τ 3 + D τ 6 1 − τ \ln P_r = \frac{A\tau + B\tau^{1.5} + C\tau^3 + D\tau^6}{1-\tau} ln P r ​ = 1 − τ A τ + B τ 1.5 + C τ 3 + D τ 6 ​ T c , P c T_c, P_c T c ​ , P c ​ , four constants ( A , B , C , D A, B, C, D A , B , C , D ) Entire coexistence curve (Triple point to T c T_c T c ​ ) < 0.1 % < 0.1\% < 0.1% ; complex algebra; standard in process simulator property packages.

Lee-Kesler Corresponding States ln ⁡ P r s a t = f ( 0 ) ( T r ) + ω f ( 1 ) ( T r ) \ln P_r^{sat} = f^{(0)}(T_r) + \omega f^{(1)}(T_r) ln P r s a t ​ = f ( 0 ) ( T r ​ ) + ω f ( 1 ) ( T r ​ ) T c , P c T_c, P_c T c ​ , P c ​ , acentric factor ω \omega ω Generalized for non-polar to slightly polar fluids 1 − 3 % 1-3\% 1 − 3% error; ideal when empirical Antoine constants are unavailable.

  • 7. Comprehensive Worked Numerical Example: Vacuum Distillation Reboiler Analysis
  • Problem Statement

A chemical plant purifies n-hexane ( C 6 H 14 \text{C}_6\text{H}_{14} C 6 ​ H 14 ​ , M W = 86.18 g/mol MW = 86.18\text{ g/mol} M W = 86.18 g/mol ) in a continuous vacuum distillation column. The reboiler operates at an absolute pressure of P r e b = 250.0 mmHg P_{reb} = 250.0\text{ mmHg} P re b ​ = 250.0 mmHg ( 0.3289 atm = 33.33 kPa 0.3289\text{ atm} = 33.33\text{ kPa} 0.3289 atm = 33.33 kPa ).

The NCEES PE Chemical Reference Handbook supplies the following Antoine constants for n-hexane: log ⁡ 10 ( P s a t [ mmHg ] ) = A − B T [ ∘ C ] + C \log_{10}\left(P^{sat}[\text{mmHg}]\right) = A - \frac{B}{T[^\circ\text{C}] + C} lo g 10 ​ ( P s a t [ mmHg ] ) = A − T [ ∘ C ] + C B ​

Where:

  • A = 6.87776 A = 6.87776 A = 6.87776
  • B = 1171.53 B = 1171.53 B = 1171.53
  • C = 224.366 C = 224.366 C = 224.366
  • Valid range: − 13 ∘ C -13^\circ\text{C} − 1 3 ∘ C to 95 ∘ C 95^\circ\text{C} 9 5 ∘ C

Calculate:

The degrees of freedom ( F F F ) for the boiling liquid-vapor mixture inside the reboiler.

The operating temperature ( T r e b T_{reb} T re b ​ ) inside the reboiler in ∘ C ^\circ\text{C} ∘ C and K \text{K} K .

The normal boiling point ( T b T_b T b ​ at P = 760.0 mmHg P = 760.0\text{ mmHg} P = 760.0 mmHg ) of n-hexane.

The latent heat of vaporization ( Δ H v a p \Delta H_{vap} Δ H v a p ​ ) at the reboiler operating temperature using the combined Clausius-Clapeyron and Antoine derivative relationship: d ln ⁡ P s a t d T = Δ H v a p R T 2 \frac{d\ln P^{sat}}{dT} = \frac{\Delta H_{vap}}{R T^2} d T d ln P s a t ​ = R T 2 Δ H v a p ​ ​

The percentage reduction in reboiler operating temperature achieved by pulling vacuum ( 250 mmHg 250\text{ mmHg} 250 mmHg ) compared to atmospheric operation ( 760 mmHg 760\text{ mmHg} 760 mmHg ).

  • Step 1: Degrees of Freedom Analysis
  • Apply the Gibbs Phase Rule for a non-reacting system: F = C − P + 2 F = C - P + 2 F = C − P + 2

Number of components: C = 1 C = 1 C = 1 (pure n-hexane).

Number of phases: P = 2 P = 2 P = 2 (saturated liquid + saturated vapor). F = 1 − 2 + 2 = 1 F = 1 - 2 + 2 = \mathbf{1} F = 1 − 2 + 2 = 1

There is 1 degree of freedom . Because the plant operator fixes the operating pressure at P r e b = 250.0 mmHg P_{reb} = 250.0\text{ mmHg} P re b ​ = 250.0 mmHg , the system variance is exhausted ( 1 − 1 = 0 1 - 1 = 0 1 − 1 = 0 ). The boiling temperature is completely constrained by thermodynamics and cannot be adjusted independently.

Step 2: Reboiler Operating Temperature ( T r e b T_{reb} T re b ​ )

Rearrange the Antoine equation to solve explicitly for T T T : log ⁡ 10 ( P s a t ) = A − B T + C ⟹ T = B A − log ⁡ 10 ( P s a t ) − C \log_{10}(P^{sat}) = A - \frac{B}{T + C} \implies T = \frac{B}{A - \log_{10}(P^{sat})} - C lo g 10 ​ ( P s a t ) = A − T + C B ​ ⟹ T = A − lo g 10 ​ ( P s a t ) B ​ − C

Evaluate log ⁡ 10 ( 250.0 ) \log_{10}(250.0) lo g 10 ​ ( 250.0 ) : log ⁡ 10 ( 250.0 ) = 2.397940 \log_{10}(250.0) = 2.397940 lo g 10 ​ ( 250.0 ) = 2.397940

Substitute constants: T r e b = 1171.53 6.87776 − 2.397940 − 224.366 T_{reb} = \frac{1171.53}{6.87776 - 2.397940} - 224.366 T re b ​ = 6.87776 − 2.397940 1171.53 ​ − 224.366 T r e b = 1171.53 4.479820 − 224.366 = 261.5127 − 224.366 = 37.15 ∘ C T_{reb} = \frac{1171.53}{4.479820} - 224.366 = 261.5127 - 224.366 = \mathbf{37.15^\circ\text{C}} T re b ​ = 4.479820 1171.53 ​ − 224.366 = 261.5127 − 224.366 = 37.1 5 ∘ C

Convert to absolute temperature: T r e b = 37.147 + 273.15 = 310.30 K T_{reb} = 37.147 + 273.15 = \mathbf{310.30\text{ K}} T re b ​ = 37.147 + 273.15 = 310.30 K

Step 3: Normal Boiling Point Determination

At atmospheric pressure, P s a t = 760.0 mmHg P^{sat} = 760.0\text{ mmHg} P s a t = 760.0 mmHg : log ⁡ 10 ( 760.0 ) = 2.880814 \log_{10}(760.0) = 2.880814 lo g 10 ​ ( 760.0 ) = 2.880814 T b = 1171.53 6.87776 − 2.880814 − 224.366 = 1171.53 3.996946 − 224.366 T_b = \frac{1171.53}{6.87776 - 2.880814} - 224.366 = \frac{1171.53}{3.996946} - 224.366 T b ​ = 6.87776 − 2.880814 1171.53 ​ − 224.366 = 3.996946 1171.53 ​ − 224.366 T b = 293.106 − 224.366 = 68.74 ∘ C ( 341.89 K ) T_b = 293.106 - 224.366 = \mathbf{68.74^\circ\text{C}} \quad (341.89\text{ K}) T b ​ = 293.106 − 224.366 = 68.7 4 ∘ C ( 341.89 K )

(Literature experimental normal boiling point of n-hexane is 68.7 ∘ C 68.7^\circ\text{C} 68. 7 ∘ C ; calculation matches exactly).

Step 4: Latent Heat of Vaporization ( Δ H v a p \Delta H_{vap} Δ H v a p ​ ) at Reboiler Conditions

From the Clausius-Clapeyron equation: d ln ⁡ P s a t d T = Δ H v a p R T 2 ⟹ Δ H v a p = R T 2 ( d ln ⁡ P s a t d T ) \frac{d\ln P^{sat}}{dT} = \frac{\Delta H_{vap}}{R T^2} \implies \Delta H_{vap} = R T^2 \left( \frac{d\ln P^{sat}}{dT} \right) d T d ln P s a t ​ = R T 2 Δ H v a p ​ ​ ⟹ Δ H v a p ​ = R T 2 ( d T d ln P s a t ​ )

Relate natural log to base-10 log: ln ⁡ P s a t = ln ⁡ ( 10 ) ⋅ log ⁡ 10 P s a t = 2.302585 ⋅ ( A − B T + C ) \ln P^{sat} = \ln(10) \cdot \log_{10} P^{sat} = 2.302585 \cdot \left( A - \frac{B}{T + C} \right) ln P s a t = ln ( 10 ) ⋅ lo g 10 ​ P s a t = 2.302585 ⋅ ( A − T + C B ​ )

Differentiating with respect to temperature ( T T T in ∘ C ^\circ\text{C} ∘ C or K \text{K} K , since d ( T [ ∘ C ] ) = d ( T [ K ] ) d(T[^\circ\text{C}]) = d(T[\text{K}]) d ( T [ ∘ C ]) = d ( T [ K ]) ): d ln ⁡ P s a t d T = 2.302585 ⋅ B ( T [ ∘ C ] + C ) 2 \frac{d\ln P^{sat}}{dT} = 2.302585 \cdot \frac{B}{(T[^\circ\text{C}] + C)^2} d T d ln P s a t ​ = 2.302585 ⋅ ( T [ ∘ C ] + C ) 2 B ​

Substitute T r e b = 37.147 ∘ C T_{reb} = 37.147^\circ\text{C} T re b ​ = 37.14 7 ∘ C , B = 1171.53 B = 1171.53 B = 1171.53 , and C = 224.366 C = 224.366 C = 224.366 : T [ ∘ C ] + C = 37.147 + 224.366 = 261.513 T[^\circ\text{C}] + C = 37.147 + 224.366 = 261.513 T [ ∘ C ] + C = 37.147 + 224.366 = 261.513 ( T + C ) 2 = ( 261.513 ) 2 = 68 , 389.05 (T + C)^2 = (261.513)^2 = 68,389.05 ( T + C ) 2 = ( 261.513 ) 2 = 68 , 389.05 d ln ⁡ P s a t d T = 2.302585 × 1171.53 68 , 389.05 = 2697.547 68 , 389.05 = 0.039444 K − 1 \frac{d\ln P^{sat}}{dT} = \frac{2.302585 \times 1171.53}{68,389.05} = \frac{2697.547}{68,389.05} = \mathbf{0.039444\text{ K}^{-1}} d T d ln P s a t ​ = 68 , 389.05 2.302585 × 1171.53 ​ = 68 , 389.05 2697.547 ​ = 0.039444 K − 1

Now calculate Δ H v a p \Delta H_{vap} Δ H v a p ​ at T = 310.30 K T = 310.30\text{ K} T = 310.30 K using R = 8.31447 J/(mol ⋅ K) R = 8.31447\text{ J/(mol}\cdot\text{K)} R = 8.31447 J/(mol ⋅ K) : T 2 = ( 310.30 K ) 2 = 96 , 286.09 K 2 T^2 = (310.30\text{ K})^2 = 96,286.09\text{ K}^2 T 2 = ( 310.30 K ) 2 = 96 , 286.09 K 2 Δ H v a p = ( 8.31447 J/(mol ⋅ K) ) × ( 96 , 286.09 K 2 ) × ( 0.039444 K − 1 ) \Delta H_{vap} = \left( 8.31447\text{ J/(mol}\cdot\text{K)} \right) \times \left( 96,286.09\text{ K}^2 \right) \times \left( 0.039444\text{ K}^{-1} \right) Δ H v a p ​ = ( 8.31447 J/(mol ⋅ K) ) × ( 96 , 286.09 K 2 ) × ( 0.039444 K − 1 ) Δ H v a p = 8.31447 × 3797.91 = 31 , 577 J/mol = 31.58 kJ/mol \Delta H_{vap} = 8.31447 \times 3797.91 = \mathbf{31,577\text{ J/mol}} = \mathbf{31.58\text{ kJ/mol}} Δ H v a p ​ = 8.31447 × 3797.91 = 31 , 577 J/mol = 31.58 kJ/mol

In specific mass units: Δ h v a p = 31 , 577 J/mol 0.08618 kg/mol = 366 , 408 J/kg = 366.4 kJ/kg \Delta h_{vap} = \frac{31,577\text{ J/mol}}{0.08618\text{ kg/mol}} = 366,408\text{ J/kg} = \mathbf{366.4\text{ kJ/kg}} Δ h v a p ​ = 0.08618 kg/mol 31 , 577 J/mol ​ = 366 , 408 J/kg = 366.4 kJ/kg

(Literature experimental value for n-hexane at 37 ∘ C 37^\circ\text{C} 3 7 ∘ C is 31.6 kJ/mol 31.6\text{ kJ/mol} 31.6 kJ/mol ; exact agreement demonstrates the thermodynamic consistency between the Antoine derivative and latent heat).

Step 5: Vacuum Temperature Reduction Δ T = T b − T r e b = 68.74 ∘ C − 37.15 ∘ C = 31.59 ∘ C \Delta T = T_b - T_{reb} = 68.74^\circ\text{C} - 37.15^\circ\text{C} = \mathbf{31.59^\circ\text{C}} Δ T = T b ​ − T re b ​ = 68.7 4 ∘ C − 37.1 5 ∘ C = 31.5 9 ∘ C Percentage Reduction (Absolute Scale) = 341.89 K − 310.30 K 341.89 K × 100 % = 9.24 % \text{Percentage Reduction (Absolute Scale)} = \frac{341.89\text{ K} - 310.30\text{ K}}{341.89\text{ K}} \times 100\% = \mathbf{9.24\%} Percentage Reduction (Absolute Scale) = 341.89 K 341.89 K − 310.30 K ​ × 100% = 9.24%

Operating the reboiler under a vacuum of 250 mmHg 250\text{ mmHg} 250 mmHg lowers the boiling point by 31.6 ∘ C 31.6^\circ\text{C} 31. 6 ∘ C . In industrial practice, this thermal reduction permits the use of low-pressure utility waste steam ( 100 ∘ C 100^\circ\text{C} 10 0 ∘ C ) as the reboiler heating medium instead of expensive high-pressure steam, and prevents heat-sensitive chemicals from thermal degradation and fouling.

  • 8. Critical PE Exam Traps & Pitfalls
  • Trap 1: The Antoine Equation Unit Catastrophe

Antoine constants are purely empirical curve-fit parameters tied to exact units. You must verify three items before pressing buttons on your calculator:

Base-10 vs. Natural Logarithm : Does the formula specify log ⁡ 10 ( P ) \log_{10}(P) lo g 10 ​ ( P ) or ln ⁡ ( P ) \ln(P) ln ( P ) ? Entering a natural logarithm into a base-10 equation produces an error factor of ln ⁡ ( 10 ) ≈ 2.303 \ln(10) \approx 2.303 ln ( 10 ) ≈ 2.303 .

Temperature Scale : Does the parameter C C C expect Celsius ( ∘ C ^\circ\text{C} ∘ C ) or Kelvin ( K \text{K} K )? If C ≈ 200 − 250 C \approx 200-250 C ≈ 200 − 250 , the equation almost certainly expects ∘ C ^\circ\text{C} ∘ C . If C ≈ − 30 C \approx -30 C ≈ − 30 to − 50 -50 − 50 , it expects K \text{K} K .

Pressure Units : Does the formula evaluate pressure in mmHg \text{mmHg} mmHg , bar \text{bar} bar , kPa \text{kPa} kPa , or psia \text{psia} psia ? Look at the table header carefully.

Trap 2: Extrapolating the Clausius-Clapeyron Equation Near the Critical Point

The Clausius-Clapeyron equation assumes Δ v v a p ≈ v V \Delta v_{vap} \approx v^V Δ v v a p ​ ≈ v V and ideal gas behavior ( Z = 1 Z = 1 Z = 1 ). Near the critical point ( T r > 0.85 T_r > 0.85 T r ​ > 0.85 ), saturated liquid volume expands dramatically, vapor compressibility drops to Z c ≈ 0.27 Z_c \approx 0.27 Z c ​ ≈ 0.27 , and Δ H v a p \Delta H_{vap} Δ H v a p ​ plummets toward zero. Using Clausius-Clapeyron to estimate vapor pressures above 0.8 T c 0.8 T_c 0.8 T c ​ results in errors exceeding 30 − 50 % 30-50\% 30 − 50% .

Trap 3: Misapplying the Phase Rule to Partially Miscible or Immiscible Systems

When two liquids are completely immiscible (e.g., liquid water + liquid toluene in a steam stripping vessel), they form two distinct liquid phases . Candidates often count the liquid mixture as a single phase ( P = 1 P = 1 P = 1 ). For water + toluene + vapor: C = 2 , P = 3 ⟹ F = 2 − 3 + 2 = 1 C = 2, P = 3 \implies F = 2 - 3 + 2 = 1 C = 2 , P = 3 ⟹ F = 2 − 3 + 2 = 1 . Fixing total system pressure completely fixes the three-phase boiling temperature, meaning the mixture boils at a temperature lower than the normal boiling point of either pure component.