Study guide
19.2 Process Equipment Selection, Sizing, and Optimization
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
19.2 Process Equipment Selection, Sizing, and Optimization
Key Takeaways Explain This Topic AI
Vapor-liquid separator diameter follows the Souders-Brown relation v m a x = K ( ρ L − ρ V ) / ρ V v_{max} = K \sqrt{(\rho_L - \rho_V)/\rho_V} v ma x = K ( ρ L − ρ V ) / ρ V , with K ≈ 0.107 m/s K \approx 0.107\text{ m/s} K ≈ 0.107 m/s ( 0.35 ft/s 0.35\text{ ft/s} 0.35 ft/s ) for a vertical drum fitted with a mesh pad.
Centrifugal pumps suit high flow, moderate head, and low viscosity; positive displacement pumps are required for high viscosity, low flow at high head, and metering duty, and they must never be operated against a closed discharge without a relief path.
Centrifugal compressors suit high flow at moderate compression ratio; reciprocating compressors suit low flow at high compression ratio, and both are limited by discharge temperature, which forces multistaging with intercooling.
Any capital-versus-operating optimum is found by setting d C t o t a l / d x = 0 dC_{total}/dx = 0 d C t o t a l / d x = 0 ; when capital rises linearly and operating cost falls as (1/x), the optimum is x ∗ = a / b x^* = \sqrt{a/b} x ∗ = a / b and the two cost terms are equal at the optimum .
Optimum reflux ratio for a distillation column lies at roughly 1.1 to 1.2 times R m i n R_{min} R min , because column cost rises steeply as R → R m i n R \to R_{min} R → R min (infinite stages) while utility cost rises steadily as (R) increases.
Last updated: September 2026
19.2 Process Equipment Selection, Sizing, and Optimization
The NCEES specification names Process equipment design (e.g., equipment selection, optimization, sizing) under Design. Exam questions in this subtopic are short: pick the right machine for a stated duty, or size one piece of equipment from a standard correlation, or find the economic optimum of a single design variable.
- 1. Selection Logic
- Pumps
Duty Choice Why
High flow, moderate head, μ < 100 cP \mu < 100\text{ cP} μ < 100 cP Centrifugal Cheapest, simplest, smooth flow, throttleable
High viscosity ( > ∼ 500 cP > \sim 500\text{ cP} >∼ 500 cP ) Positive displacement (gear, screw, progressing cavity) Centrifugal head and efficiency collapse with viscosity
- Low flow at high head PD (reciprocating, plunger) Centrifugal would need impractical impeller speed or staging
- Accurate dosing Metering (diaphragm) pump Flow set by displacement, nearly independent of discharge pressure
- Slurries Recessed-impeller or peristaltic Solids handling without trim damage
The defining behavioral difference: a centrifugal pump produces a head that falls as flow rises, so closing the discharge simply drives it to shutoff head and it survives (briefly — it will overheat). A positive displacement pump produces whatever pressure it takes to move the fixed displacement, so closing the discharge ruptures the casing or the piping. Every PD pump requires a relief valve on the discharge, upstream of the first block valve.
Compressors
- Duty Choice
- High flow, compression ratio per stage ≲ 3 \lesssim 3 ≲ 3 Centrifugal
- Low to moderate flow, high compression ratio Reciprocating
- Moderate flow, moderate ratio, dirty gas Rotary screw
- Very high flow, ratio (< 1.2) Axial or blower
Both types are limited by discharge temperature . For an ideal gas in isentropic compression, T 2 = T 1 ( P 2 / P 1 ) ( k − 1 ) / k T_2 = T_1 (P_2/P_1)^{(k-1)/k} T 2 = T 1 ( P 2 / P 1 ) ( k − 1 ) / k , so compression ratio is capped by lubricant breakdown and by the material's temperature limit. This is why large ratios are split into multiple stages with intercooling , which also minimizes total work — the optimum stage pressure ratio for (n) stages with perfect intercooling is ( P f i n a l / P i n i t i a l ) 1 / n (P_{final}/P_{initial})^{1/n} ( P f ina l / P ini t ia l ) 1/ n at each stage.
Heat exchangers
- Situation Choice
- General duty, high pressure, large area Shell and tube (Section 9.1)
Close temperature approach, clean fluids, moderate pressure Plate-and-frame — approaches of 1 − 2 ∘ C 1-2^\circ\text{C} 1 − 2 ∘ C are achievable
No cooling water available Air-cooled — approach limited to ∼ 10 − 15 ∘ C \sim 10-15^\circ\text{C} ∼ 10 − 1 5 ∘ C above ambient
- Small duty Double-pipe / hairpin
- Heavy fouling Spiral, or shell-and-tube with removable bundle and generous fouling allowance
- 2. Sizing a Vapor-Liquid Separator
Knockout drums, flash drums, compressor suction scrubbers, and reflux drums are all sized on the same principle: the upward gas velocity must be low enough that entrained droplets settle out rather than being carried over. Equating drag and gravity on a droplet gives the Souders-Brown equation: v m a x = K ρ L − ρ V ρ V v_{max} = K \sqrt{\frac{\rho_L - \rho_V}{\rho_V}} v ma x = K ρ V ρ L − ρ V
Configuration (K)
Vertical drum with mesh pad mist eliminator ≈ 0.107 m/s \approx 0.107\text{ m/s} ≈ 0.107 m/s ( 0.35 ft/s 0.35\text{ ft/s} 0.35 ft/s )
- Vertical drum without mist eliminator ≈ 0.05 − 0.07 m/s \approx 0.05-0.07\text{ m/s} ≈ 0.05 − 0.07 m/s
- Horizontal drum Higher, because the gas path is longer relative to the settling distance
Worked example. A vertical knockout drum with a mesh pad handles 2.0 m 3 /s 2.0\text{ m}^3\text{/s} 2.0 m 3 /s of vapor at ρ V = 12 kg/m 3 \rho_V = 12\text{ kg/m}^3 ρ V = 12 kg/m 3 with ρ L = 700 kg/m 3 \rho_L = 700\text{ kg/m}^3 ρ L = 700 kg/m 3 . Size the diameter. v m a x = 0.107 700 − 12 12 = 0.107 57.33 = 0.107 ( 7.572 ) = 0.810 m/s v_{max} = 0.107\sqrt{\frac{700 - 12}{12}} = 0.107\sqrt{57.33} = 0.107(7.572) = 0.810\text{ m/s} v ma x = 0.107 12 700 − 12 = 0.107 57.33 = 0.107 ( 7.572 ) = 0.810 m/s A = V ˙ v m a x = 2.0 0.810 = 2.47 m 2 D = 4 A π = 4 ( 2.47 ) π = 1.77 m A = \frac{\dot{V}}{v_{max}} = \frac{2.0}{0.810} = 2.47\text{ m}^2 \qquad D = \sqrt{\frac{4A}{\pi}} = \sqrt{\frac{4(2.47)}{\pi}} = 1.77\text{ m} A = v ma x V ˙ = 0.810 2.0 = 2.47 m 2 D = π 4 A = π 4 ( 2.47 ) = 1.77 m
Round up to a standard 1.8 m 1.8\text{ m} 1.8 m shell. Height is then set separately by liquid holdup requirements (typically 5-10 minutes between high and low level for surge, more if the drum feeds a pump) plus disengagement space above the inlet nozzle and below the mesh pad.
Note the pressure sensitivity: v m a x ∝ 1 / ρ V v_{max} \propto 1/\sqrt{\rho_V} v ma x ∝ 1/ ρ V and ρ V ∝ P \rho_V \propto P ρ V ∝ P , so a drum sized at 10 bar 10\text{ bar} 10 bar and then operated at 20 bar 20\text{ bar} 20 bar can handle a larger mass flow but a smaller volumetric one, and the same drum in vacuum service becomes enormous.
3. Economic Optimization of a Design Variable
Nearly every sizing decision is a contest between capital cost , which rises with size, and operating cost , which falls with size. The optimum is where the total is minimized: C t o t a l ( x ) = C c a p i t a l ( x ) + C o p e r a t i n g ( x ) , d C t o t a l d x = 0 C_{total}(x) = C_{capital}(x) + C_{operating}(x), \qquad \frac{dC_{total}}{dx} = 0 C t o t a l ( x ) = C c a p i t a l ( x ) + C o p er a t in g ( x ) , d x d C t o t a l = 0
The canonical form. When operating cost varies as (1/x) and annualized capital varies linearly with (x): C t o t a l = a x + b x ⟹ d C d x = − a x 2 + b = 0 ⟹ x ∗ = a / b C_{total} = \frac{a}{x} + b x \qquad \Longrightarrow \qquad \frac{dC}{dx} = -\frac{a}{x^2} + b = 0 \qquad \Longrightarrow \qquad \boxed{x^* = \sqrt{a/b}} C t o t a l = x a + b x ⟹ d x d C = − x 2 a + b = 0 ⟹ x ∗ = a / b
Example. Annual heat loss through insulation costs a / x = 8,000 / x a/x = 8{,}000/x a / x = 8 , 000/ x $ / yr \text{\textdollar}/\text{yr} $ / yr with (x) in inches, and annualized insulation capital is (bx = 500x) $ / yr \text{\textdollar}/\text{yr} $ / yr . Then x ∗ = 8,000 / 500 = 16 = 4.0 in x^* = \sqrt{8{,}000/500} = \sqrt{16} = 4.0\text{ in} x ∗ = 8 , 000/500 = 16 = 4.0 in , with C m i n = 8,000 / 4 + 500 ( 4 ) = 2,000 + 2,000 = $ 4,000 /yr C_{min} = 8{,}000/4 + 500(4) = 2{,}000 + 2{,}000 = \text{\textdollar}4{,}000\text{/yr} C min = 8 , 000/4 + 500 ( 4 ) = 2 , 000 + 2 , 000 = $ 4 , 000 /yr .
Notice that at the optimum the two cost terms are exactly equal ( $ 2,000 \text{\textdollar}2{,}000 $ 2 , 000 each). That equality is a property of this (1/x)-plus-linear form, and it makes a fast sanity check — but it does not generalize. For C = a / x 2 + b x C = a/x^2 + bx C = a / x 2 + b x the optimum has capital cost equal to twice the operating cost. Differentiate; do not assume.
The same structure recurs across the discipline:
- Design variable Capital rises with Operating falls with
- Pipe diameter More metal, larger valves and fittings Lower velocity, less friction, less pump power
- Insulation thickness More insulation installed Less heat loss
Exchanger approach Δ T \Delta T Δ T (smaller) More area (as 1 / Δ T l m 1/\Delta T_{lm} 1/Δ T l m ) Less utility consumed
- Number of effects in an evaporator More bodies Less steam per unit evaporated
- Reflux ratio Fewer stages needed — (utility cost rises with (R))
Optimum reflux ratio deserves its own note because it is shaped differently. As R → R m i n R \to R_{min} R → R min the required number of stages goes to infinity, so capital cost rises without bound; as (R) increases, stage count falls quickly at first and then flattens while reboiler and condenser duty (and column diameter) keep climbing. The total cost curve is therefore steep on the left and shallow on the right, and the minimum sits at roughly R o p t ≈ 1.1 R_{opt} \approx 1.1 R o pt ≈ 1.1 to 1.2 × R m i n 1.2 \times R_{min} 1.2 × R min . Because the curve is flat near the optimum, designers commonly select toward the upper end to buy operating flexibility cheaply.
4. Heuristics Worth Carrying Into the Exam
These are the first-pass numbers a practicing process engineer uses before any rigorous calculation, and NCEES writes judgment questions against them:
Liquid line velocity: 1 − 3 m/s 1-3\text{ m/s} 1 − 3 m/s (pump discharge), 0.5 − 1.5 m/s 0.5-1.5\text{ m/s} 0.5 − 1.5 m/s (pump suction, to protect NPSH).
Gas line velocity: 15 − 30 m/s 15-30\text{ m/s} 15 − 30 m/s .
Shell-and-tube (U): ∼ 850 W/(m 2 ⋅ K) \sim 850\text{ W/(m}^2\cdot\text{K)} ∼ 850 W/(m 2 ⋅ K) water-water, ∼ 300 \sim 300 ∼ 300 organic-water, ∼ 30 − 60 \sim 30-60 ∼ 30 − 60 gas-gas.
Minimum exchanger approach: ∼ 10 ∘ C \sim 10^\circ\text{C} ∼ 1 0 ∘ C with cooling water, ∼ 5 ∘ C \sim 5^\circ\text{C} ∼ 5 ∘ C process-process, 1 − 2 ∘ C 1-2^\circ\text{C} 1 − 2 ∘ C only in plate exchangers.
Tray spacing 0.45 − 0.60 m 0.45-0.60\text{ m} 0.45 − 0.60 m ; overall tray efficiency 50 − 70 % 50-70\% 50 − 70% for hydrocarbons.
Vessel L/D: (3) for low pressure, (4-5) at elevated pressure (shell cost favors slender vessels as pressure rises).
Design margin: size equipment for roughly 110 − 120 % 110-120\% 110 − 120% of design rate, and motors for the maximum possible operating point, not the normal one.