Study guide
12.3 Adsorption, Membrane Separations, and Drying Operations
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
12.3 Adsorption, Membrane Separations, and Drying Operations
Key Takeaways Explain This Topic AI
Adsorption isotherms quantify solid-fluid equilibrium: the Langmuir model (q = q_max * K * C / (1 + K * C)) assumes localized monolayer coverage on identical sites, whereas the Freundlich model (q = K_F * C^(1/n)) models multilayer adsorption on heterogeneous surfaces.
Fixed-bed breakthrough curves exhibit a Mass Transfer Zone (MTZ) that migrates downstream; breakthrough time t_b occurs when effluent concentration reaches a threshold (typically C/C_0 = 0.05), and bed length unused at breakthrough is governed by the length of the MTZ.
In Reverse Osmosis (RO), solvent water flux is driven by net hydraulic overpressure (J_w = A_w * (Delta_P - Delta_Pi)), whereas solute salt flux is driven purely by concentration gradient (J_s = B_s * Delta_C); increasing operating pressure Delta_P dilutes permeate, directly increasing salt rejection R_j.
Solid moisture content MUST be computed on a dry basis (X = mass water / mass dry solid) for drying calculations; using wet basis (x = mass water / total wet mass) produces severe errors because dry solid mass m_s is the only invariant reference.
Drying proceeds through a Constant Rate Period (surface liquid film evaporates at wet-bulb temperature T_wb, governed by convective heat transfer R_c = h * (T_db - T_wb) / lambda) followed by a Falling Rate Period below critical moisture X_c where internal diffusion limits drying rate.
Last updated: September 2026
12.3 Adsorption, Membrane Separations, and Drying Operations
Beyond traditional gas-liquid and liquid-liquid contacting towers, chemical engineers frequently deploy specialized rate-controlled and solid-fluid separation operations. Adsorption captures trace pollutants or purifies products via solid surface forces; membrane separations achieve molecular-scale separations without phase changes; and drying removes volatile liquids from solid matrices to produce stable particulate products. Each of these three operations possesses unique governing equations, transport mechanisms, and design pitfalls tested on the NCEES PE Chemical Exam .
1. Adsorption Equilibria and Fixed-Bed Dynamics
Adsorption transfers solute molecules (adsorbates) from a gas or liquid phase onto the surface of a porous solid (adsorbent). Distinguish physical adsorption (physisorption) , driven by weak van der Waals forces and easily reversible with heat, from chemical adsorption (chemisorption) , which involves valence electron sharing, high activation energy, and formation of a surface monolayer.
Industrial Adsorbents
Activated Carbon : Hydrophobic; non-polar; specific surface area 600 − 1 , 500 m 2 /g 600-1,500\text{ m}^2\text{/g} 600 − 1 , 500 m 2 /g . Standard for VOC abatement, organic wastewater treatment, and solvent recovery.
Molecular Sieve Zeolites : Crystalline aluminosilicates with uniform molecular pore apertures ( 3 A ˚ , 4 A ˚ , 5 A ˚ , 10 A ˚ 3\text{ Å}, 4\text{ Å}, 5\text{ Å}, 10\text{ Å} 3 A ˚ , 4 A ˚ , 5 A ˚ , 10 A ˚ ). Highly polar; widely used for deep gas drying, natural gas dehydration, and air separation ( N 2 / O 2 N_2/O_2 N 2 / O 2 ).
Silica Gel & Activated Alumina : Hydrophilic metal oxides; high affinity for water vapor and polar compounds.
1. The Langmuir Adsorption Isotherm
The Langmuir model assumes reversible adsorption onto a fixed number of equivalent, localized surface sites with zero lateral interaction between adsorbed molecules (monolayer coverage): q = q m a x ⋅ K ⋅ C 1 + K ⋅ C ( Liquid Systems ) q = \frac{q_{max} \cdot K \cdot C}{1 + K \cdot C} \quad (\text{Liquid Systems}) q = 1 + K ⋅ C q ma x ⋅ K ⋅ C ( Liquid Systems ) q = q m a x ⋅ b ⋅ P 1 + b ⋅ P ( Gas Systems ) q = \frac{q_{max} \cdot b \cdot P}{1 + b \cdot P} \quad (\text{Gas Systems}) q = 1 + b ⋅ P q ma x ⋅ b ⋅ P ( Gas Systems )
Where:
q q q = equilibrium adsorbent loading ( mg solute / g adsorbent \text{mg solute / g adsorbent} mg solute / g adsorbent or mol/kg \text{mol/kg} mol/kg ).
q m a x q_{max} q ma x = maximum theoretical monolayer saturation capacity ( mg/g \text{mg/g} mg/g or mol/kg \text{mol/kg} mol/kg ).
K K K or b b b = Langmuir equilibrium adsorption constant ( L/mg \text{L/mg} L/mg or atm − 1 \text{atm}^{-1} atm − 1 ), proportional to the energy of adsorption.
C C C or P P P = fluid solute equilibrium concentration ( mg/L \text{mg/L} mg/L ) or partial pressure ( atm \text{atm} atm ).
Linearization for Parameter Extraction: C q = 1 q m a x K + 1 q m a x C \frac{C}{q} = \frac{1}{q_{max} K} + \frac{1}{q_{max}} C q C = q ma x K 1 + q ma x 1 C
A plot of C / q C/q C / q (y-axis) versus C C C (x-axis) yields a straight line where: Slope = 1 q m a x ⟹ q m a x = 1 Slope \text{Slope} = \frac{1}{q_{max}} \implies q_{max} = \frac{1}{\text{Slope}} Slope = q ma x 1 ⟹ q ma x = Slope 1 y-Intercept = 1 q m a x K ⟹ K = Slope y-Intercept \text{y-Intercept} = \frac{1}{q_{max} K} \implies K = \frac{\text{Slope}}{\text{y-Intercept}} y-Intercept = q ma x K 1 ⟹ K = y-Intercept Slope
2. The Freundlich Adsorption Isotherm
The empirical Freundlich model describes multilayer adsorption on heterogeneous surfaces with non-uniform site energies: q = K F ⋅ C 1 / n q = K_F \cdot C^{1/n} q = K F ⋅ C 1/ n
Where:
K F K_F K F = Freundlich capacity parameter ( (mg/g)(L/mg) 1 / n \text{(mg/g)(L/mg)}^{1/n} (mg/g)(L/mg) 1/ n ).
n n n = heterogeneity factor ( n > 1 n > 1 n > 1 represents favorable adsorption; 1 / n < 1 1/n < 1 1/ n < 1 ).
Linearization: ln ( q ) = ln ( K F ) + 1 n ln ( C ) \ln(q) = \ln(K_F) + \frac{1}{n} \ln(C) ln ( q ) = ln ( K F ) + n 1 ln ( C )
A log-log plot of ln ( q ) \ln(q) ln ( q ) versus ln ( C ) \ln(C) ln ( C ) yields slope 1 / n 1/n 1/ n and y-intercept ln ( K F ) \ln(K_F) ln ( K F ) . Adsorption Isotherms Fixed-Bed Breakthrough Curve
- q ^ C/C_0 ^
- | Langmuir (Asymptotic q_max) 1.0 | /--- Exhaustion (t_e)
- | /------------------ | / (C/C_0 = 0.95)
- | / | /
- | / Freundlich (Multilayer) | MTZ /
- | / / | ======== /
- | / / | /
- | / / | Breakthrough (t_b)
- | / / 0.0 | (C/C_0 = 0.05)
- +------------------------> C +-----------------------> Time (t)
- Fixed-Bed Adsorption Dynamics & Breakthrough
In industrial fixed-bed adsorbers, fluid containing solute at concentration C 0 C_0 C 0 flows downward through a bed of packed solid adsorbent of total length L L L .
Mass Transfer Zone (MTZ) : The active band within the bed where mass transfer occurs. Upstream of the MTZ, the adsorbent is completely saturated ( q = q 0 q = q_0 q = q 0 ). Downstream of the MTZ, the bed remains virgin ( q = 0 q = 0 q = 0 ).
Breakthrough Time ( t b t_b t b ) : The operating time at which effluent solute concentration reaches an allowable regulatory or process leakage limit (typically C / C 0 = 0.05 C/C_0 = 0.05 C / C 0 = 0.05 , or 5 % 5\% 5% of inlet concentration).
Exhaustion Time ( t e t_e t e ) : The point where the bed is essentially saturated ( C / C 0 = 0.95 C/C_0 = 0.95 C / C 0 = 0.95 , or 95 % 95\% 95% ).
Length of the Mass Transfer Zone ( L M T Z L_{MTZ} L MTZ ) : L M T Z = L [ t e − t b t e − ( 1 − f ) ( t e − t b ) ] L_{MTZ} = L \left[ \frac{t_e - t_b}{t_e - (1 - f)(t_e - t_b)} \right] L MTZ = L [ t e − ( 1 − f ) ( t e − t b ) t e − t b ]
Where f f f is the fractional saturation of the MTZ (typically f ≈ 0.50 f \approx 0.50 f ≈ 0.50 for symmetrical S-shaped breakthrough curves). The length of bed unused at breakthrough is L U B = ( 1 − f ) L M T Z LUB = (1 - f) L_{MTZ} LU B = ( 1 − f ) L MTZ . A narrower MTZ yields higher bed utilization before breakthrough.
2. Membrane Separations: Gas Permeation & Reverse Osmosis
Membranes separate components by using a semipermeable synthetic barrier that permits selective transport of certain chemical species while restricting others. Transport through non-porous dense polymeric membranes follows the solution-diffusion mechanism :
Sorption of penetrant molecules into the high-pressure upstream membrane surface.
Molecular diffusion across the dense selective layer driven by chemical potential gradient.
Desorption from the low-pressure downstream membrane surface into the permeate.
1. Gas Permeation
For a gas component i i i , the volumetric permeation flux ( J i J_i J i , in cm 3 (STP)/(cm 2 ⋅ s) \text{cm}^3\text{(STP)/(cm}^2\cdot\text{s)} cm 3 (STP)/(cm 2 ⋅ s) or mol/(m 2 ⋅ s) \text{mol/(m}^2\cdot\text{s)} mol/(m 2 ⋅ s) ) through a dense selective layer of thickness l l l is: J i = P M , i l ( p i , f e e d − p i , p e r m ) = ( P M , i l ) Δ p i J_i = \frac{P_{M,i}}{l} \left( p_{i,feed} - p_{i,perm} \right) = \left( \frac{P_{M,i}}{l} \right) \Delta p_i J i = l P M , i ( p i , f ee d − p i , p er m ) = ( l P M , i ) Δ p i
Where:
P M , i P_{M,i} P M , i = membrane permeability coefficient ( P M , i = D i ⋅ S i P_{M,i} = D_i \cdot S_i P M , i = D i ⋅ S i , the product of diffusivity D i D_i D i and solubility S i S_i S i ). Standard unit is the Barrer ( 1 Barrer = 10 − 10 cm 3 (STP) ⋅ cm / ( cm 2 ⋅ s ⋅ cmHg ) 1\text{ Barrer} = 10^{-10}\text{ cm}^3\text{(STP)}\cdot\text{cm}/(\text{cm}^2\cdot\text{s}\cdot\text{cmHg}) 1 Barrer = 1 0 − 10 cm 3 (STP) ⋅ cm / ( cm 2 ⋅ s ⋅ cmHg ) ).
P M , i / l P_{M,i} / l P M , i / l = permeance , expressed in Gas Permeation Units (GPU, where 1 GPU = 10 − 6 cm 3 (STP)/(cm 2 ⋅ s ⋅ cmHg ) 1\text{ GPU} = 10^{-6}\text{ cm}^3\text{(STP)/(cm}^2\cdot\text{s}\cdot\text{cmHg}) 1 GPU = 1 0 − 6 cm 3 (STP)/(cm 2 ⋅ s ⋅ cmHg ) ).
Δ p i = x i , f P f e e d − y i , p P p e r m \Delta p_i = x_{i,f} P_{feed} - y_{i,p} P_{perm} Δ p i = x i , f P f ee d − y i , p P p er m = partial pressure driving force across the membrane.
The ideal membrane selectivity (separation factor) for gas A A A over gas B B B is: α A / B = P M , A P M , B = ( D A D B ) ( S A S B ) \alpha_{A/B} = \frac{P_{M,A}}{P_{M,B}} = \left( \frac{D_A}{D_B} \right) \left( \frac{S_A}{S_B} \right) α A / B = P M , B P M , A = ( D B D A ) ( S B S A )
2. Reverse Osmosis (RO) & Osmotic Pressure Balances
In liquid systems containing dissolved salts or macromolecules, natural osmosis causes pure solvent water to migrate across a semipermeable membrane into the concentrated brine solution until equilibrium osmotic pressure is established.
Osmotic Pressure ( Π \Pi Π ) via the van 't Hoff Equation: For dilute solutions: Π = i ⋅ M ⋅ R ⋅ T = ∑ c k R T \Pi = i \cdot M \cdot R \cdot T = \sum c_k R T Π = i ⋅ M ⋅ R ⋅ T = ∑ c k RT
Where:
i i i = dimensionless van 't Hoff dissociation factor (e.g., i ≈ 2 i \approx 2 i ≈ 2 for NaCl → Na + + Cl − \text{NaCl} \to \text{Na}^+ + \text{Cl}^- NaCl → Na + + Cl − ; i ≈ 3 i \approx 3 i ≈ 3 for Na 2 SO 4 \text{Na}_2\text{SO}_4 Na 2 SO 4 ).
M M M = molar salt concentration ( mol/L \text{mol/L} mol/L or kmol/m 3 \text{kmol/m}^3 kmol/m 3 ).
R R R = ideal gas constant ( 0.08314 L ⋅ bar/(mol ⋅ K) 0.08314\text{ L}\cdot\text{bar/(mol}\cdot\text{K)} 0.08314 L ⋅ bar/(mol ⋅ K) or 8.314 kPa ⋅ m 3 /(kmol ⋅ K) 8.314\text{ kPa}\cdot\text{m}^3\text{/(kmol}\cdot\text{K)} 8.314 kPa ⋅ m 3 /(kmol ⋅ K) ).
T T T = absolute temperature ( K \text{K} K ).
Water Flux ( J w J_w J w ): To force water from the saline solution into the fresh water permeate ( Reverse Osmosis ), an applied hydraulic pressure difference ( Δ P \Delta P Δ P ) exceeding the osmotic pressure difference ( Δ Π \Delta \Pi ΔΠ ) must be imposed: J w = A w ⋅ ( Δ P − Δ Π ) = A w ⋅ [ ( P f − P p ) − ( Π f − Π p ) ] J_w = A_w \cdot (\Delta P - \Delta \Pi) = A_w \cdot \left[ (P_f - P_p) - (\Pi_f - \Pi_p) \right] J w = A w ⋅ ( Δ P − ΔΠ ) = A w ⋅ [ ( P f − P p ) − ( Π f − Π p ) ]
Where:
A w A_w A w = water permeability coefficient (permeance) of the membrane ( m 3 / ( m 2 ⋅ s ⋅ bar ) \text{m}^3/(\text{m}^2\cdot\text{s}\cdot\text{bar}) m 3 / ( m 2 ⋅ s ⋅ bar ) or LMH/bar \text{LMH/bar} LMH/bar , where LMH = L / ( m 2 ⋅ h ) \text{LMH} = \text{L}/(\text{m}^2\cdot\text{h}) LMH = L / ( m 2 ⋅ h ) ).
Δ P = P f e e d − P p e r m e a t e \Delta P = P_{feed} - P_{permeate} Δ P = P f ee d − P p er m e a t e = applied transmembrane hydraulic pressure difference.
Δ Π = Π f e e d − Π p e r m e a t e \Delta \Pi = \Pi_{feed} - \Pi_{permeate} ΔΠ = Π f ee d − Π p er m e a t e = transmembrane osmotic pressure difference.
Solute (Salt) Flux ( J s J_s J s ): Salt transport across a non-porous RO membrane occurs via molecular diffusion, driven strictly by the concentration gradient , completely independent of the applied hydraulic pressure Δ P \Delta P Δ P : J s = B s ⋅ ( C f − C p ) J_s = B_s \cdot (C_f - C_p) J s = B s ⋅ ( C f − C p )
Where B s B_s B s is the solute permeability coefficient ( m/s \text{m/s} m/s or LMH \text{LMH} LMH ), and C f , C p C_f, C_p C f , C p are feed and permeate solute concentrations ( mg/L \text{mg/L} mg/L ).
Permeate Solute Concentration ( C p C_p C p ) and Salt Rejection ( R j R_j R j ): Since solute and solvent flow simultaneously: C p = J s J w = B s ( C f − C p ) J w ⟹ C p = C f ( B s J w + B s ) C_p = \frac{J_s}{J_w} = \frac{B_s (C_f - C_p)}{J_w} \implies C_p = C_f \left( \frac{B_s}{J_w + B_s} \right) C p = J w J s = J w B s ( C f − C p ) ⟹ C p = C f ( J w + B s B s )
Observed Salt Rejection ( R j R_j R j ): R j ≡ 1 − C p C f = J w J w + B s R_j \equiv 1 - \frac{C_p}{C_f} = \frac{J_w}{J_w + B_s} R j ≡ 1 − C f C p = J w + B s J w
Important
Why Increasing Pressure Improves Water Purity:
As applied hydraulic pressure Δ P \Delta P Δ P increases, water flux J w J_w J w rises linearly ( J w ∝ Δ P − Δ Π J_w \propto \Delta P - \Delta \Pi J w ∝ Δ P − ΔΠ ). However, solute flux J s J_s J s remains constant. Consequently, higher operating pressure dilutes the salt in the permeate stream , directly increasing salt rejection R j R_j R j !
3. Drying Operations & Psychrometry
Drying removes volatile liquids (typically water) from a solid, wet cake, or slurry by thermal vaporization to produce a dry solid product.
1. Solid Moisture Content Definitions
Caution
THE MOST COMMON PE EXAM DRYING ERROR:
Never confuse wet basis moisture ( x x x ) with dry basis moisture ( X X X ) ! As drying proceeds, the mass of water decreases while the mass of bone-dry solid ( m s m_s m s ) remains strictly constant. All kinetic rate equations require moisture on a dry basis .
Wet Basis Moisture ( x x x ) : Mass fraction of water relative to total wet solid: x = m w m w + m s x = \frac{m_w}{m_w + m_s} x = m w + m s m w
Dry Basis Moisture ( X X X ) : Mass ratio of water relative to invariant dry solid: X = m w m s X = \frac{m_w}{m_s} X = m s m w
Conversion Formulas : X = x 1 − x , x = X 1 + X X = \frac{x}{1 - x}, \quad x = \frac{X}{1 + X} X = 1 − x x , x = 1 + X X
Free Moisture ( X f r e e X_{free} X f ree ) : The moisture evaporable under the prevailing drying air conditions: X f r e e = X − X e q X_{free} = X - X_{eq} X f ree = X − X e q Where X e q X_{eq} X e q is the equilibrium moisture content determined by the solid's sorption isotherm at the air's relative humidity and temperature. Moisture below X e q X_{eq} X e q cannot be removed by air drying. Drying Rate Curve (R vs. X)
- Drying Rate (R) ^
- | Constant Rate Period
- R_c | +--------------------+
- | /| |
- | / |
- | / |
- | Falling / |
- | Rate / |
- | Period / |
- | / |
- +-------+-------+--------------------+---> Dry Basis Moisture (X)
- X_eq X_c X_1
- (Equil) (Critical) (Initial)
- 2. The Drying Rate Curve & Drying Kinetics
Batch drying under constant external air conditions (constant temperature, humidity, and air velocity) exhibits two distinct regimes separated by the Critical Moisture Content ( X c X_c X c ) :
Period 1: Constant Rate Period ( X > X c X > X_c X > X c )
Water evaporates freely from a continuous, saturated liquid film covering the outer solid surface.
The drying rate is entirely externally mass- and heat-transfer controlled (independent of solid thickness or porosity).
The solid surface temperature remains constant at the wet-bulb temperature ( T s = T w b T_s = T_{wb} T s = T w b ) of the drying air.
The constant drying rate R c R_c R c ( kg water/(m 2 ⋅ h) \text{kg water/(m}^2\cdot\text{h)} kg water/(m 2 ⋅ h) ) is given by: R c = h ( T d b − T w b ) λ w = k y ( Y s a t − Y a i r ) R_c = \frac{h (T_{db} - T_{wb})}{\lambda_w} = k_y (Y_{sat} - Y_{air}) R c = λ w h ( T d b − T w b ) = k y ( Y s a t − Y ai r ) Where h h h is the convective heat transfer coefficient, T d b T_{db} T d b is the dry-bulb temperature, T w b T_{wb} T w b is the wet-bulb temperature, and λ w \lambda_w λ w is latent heat of vaporization.
Drying time in the constant rate period from initial moisture X 1 X_1 X 1 to critical moisture X c X_c X c : t c = m s A ⋅ R c ( X 1 − X c ) t_c = \frac{m_s}{A \cdot R_c} (X_1 - X_c) t c = A ⋅ R c m s ( X 1 − X c ) Where m s m_s m s is bone-dry solid mass ( kg \text{kg} kg ) and A A A is exposed drying surface area ( m 2 \text{m}^2 m 2 ).
Period 2: Falling Rate Period ( X e q < X < X c X_{eq} < X < X_c X e q < X < X c )
At X c X_c X c , the continuous surface liquid film ruptures; dry patches appear. Liquid must diffuse or wick through internal solid pores to reach the drying surface.
Drying is internally mass-transfer controlled ; the solid surface temperature rises toward the air dry-bulb temperature ( T d b T_{db} T d b ).
In the standard linear falling rate model, the drying rate is directly proportional to free moisture: R ( X ) = R c ( X − X e q X c − X e q ) R(X) = R_c \left( \frac{X - X_{eq}}{X_c - X_{eq}} \right) R ( X ) = R c ( X c − X e q X − X e q )
Drying time in the falling rate period from X c X_c X c down to target final moisture X 2 X_2 X 2 : t f = − m s A ∫ X c X 2 d X R ( X ) = m s ( X c − X e q ) A ⋅ R c ln ( X c − X e q X 2 − X e q ) t_f = -\frac{m_s}{A} \int_{X_c}^{X_2} \frac{dX}{R(X)} = \frac{m_s (X_c - X_{eq})}{A \cdot R_c} \ln\left( \frac{X_c - X_{eq}}{X_2 - X_{eq}} \right) t f = − A m s ∫ X c X 2 R ( X ) d X = A ⋅ R c m s ( X c − X e q ) ln ( X 2 − X e q X c − X e q )
Total Batch Drying Time ( t t o t a l t_{total} t t o t a l ) t t o t a l = t c + t f = m s A ⋅ R c [ ( X 1 − X c ) + ( X c − X e q ) ln ( X c − X e q X 2 − X e q ) ] t_{total} = t_c + t_f = \frac{m_s}{A \cdot R_c} \left[ (X_1 - X_c) + (X_c - X_{eq}) \ln\left( \frac{X_c - X_{eq}}{X_2 - X_{eq}} \right) \right] t t o t a l = t c + t f = A ⋅ R c m s [ ( X 1 − X c ) + ( X c − X e q ) ln ( X 2 − X e q X c − X e q ) ]
4. Summary Comparison Table: Adsorption, Membrane, and Drying Parameters
Process / Technology Primary Driving Force Governing Rate Equation Limiting Phenomena Industrial Hardware
Langmuir Adsorption Chemical potential / concentration gradient q = q m a x K C / ( 1 + K C ) q = q_{max} K C / (1 + K C) q = q ma x K C / ( 1 + K C ) Surface saturation; intraparticle pore diffusion Fixed-bed vessels, TSA/PSA dual-column systems
Breakthrough Dynamics Fluid convection through porous bed u z = u 0 ρ f / ( ρ b q 0 + ϵ ρ f ) u_z = u_0 \rho_f / (\rho_b q_0 + \epsilon \rho_f) u z = u 0 ρ f / ( ρ b q 0 + ϵ ρ f ) Mass Transfer Zone ( L M T Z L_{MTZ} L MTZ ) elongation; channeling Granular activated carbon (GAC) adsorbers, molecular sieves
Reverse Osmosis (RO) Net hydraulic overpressure ( Δ P − Δ Π ) (\Delta P - \Delta \Pi) ( Δ P − ΔΠ ) J w = A w ( Δ P − Δ Π ) J_w = A_w (\Delta P - \Delta \Pi) J w = A w ( Δ P − ΔΠ ) Concentration polarization; osmotic pressure ceiling; fouling Spiral-wound modules, hollow fiber cartridges
Gas Permeation Component partial pressure ( Δ p i ) (\Delta p_i) ( Δ p i ) J i = ( P M , i / l ) Δ p i J_i = (P_{M,i} / l) \Delta p_i J i = ( P M , i / l ) Δ p i Permeate backpressure; plasticization Polyimide hollow fibers, spiral-wound envelopes
Constant Rate Drying External heat/mass transfer ( T d b − T w b ) (T_{db} - T_{wb}) ( T d b − T w b ) R c = h ( T d b − T w b ) / λ w R_c = h (T_{db} - T_{wb}) / \lambda_w R c = h ( T d b − T w b ) / λ w Boundary layer air velocity; humid air saturation Tray dryers, rotary dryers, spray dryers, fluid beds
Falling Rate Drying Internal liquid moisture diffusion / capillarity R = R c ( X − X e q ) / ( X c − X e q ) R = R_c (X - X_{eq}) / (X_c - X_{eq}) R = R c ( X − X e q ) / ( X c − X e q ) Internal pore resistance; solid thermal degradation Vacuum tray dryers, freeze dryers, tunnel kilns
- 5. Comprehensive Worked Numerical Examples
- Example A: Industrial Reverse Osmosis Desalination System Sizing
An industrial reverse osmosis facility desalinates T = 25.0 ∘ C T = 25.0^\circ\text{C} T = 25. 0 ∘ C ( 298.15 K 298.15\text{ K} 298.15 K ) brackish feed containing C f = 4 , 000.0 mg/L C_f = 4,000.0\text{ mg/L} C f = 4 , 000.0 mg/L of sodium chloride ( NaCl \text{NaCl} NaCl , M w = 58.44 g/mol M_w = 58.44\text{ g/mol} M w = 58.44 g/mol ) to produce high-purity boiler feedwater.
Operating & Membrane Parameters:
Feed hydraulic pressure: P f = 25.0 bar P_f = 25.0\text{ bar} P f = 25.0 bar ; Permeate pressure: P p = 1.0 bar P_p = 1.0\text{ bar} P p = 1.0 bar
Feed osmotic pressure: Π f = 3.20 bar \Pi_f = 3.20\text{ bar} Π f = 3.20 bar ; Permeate osmotic pressure: Π p ≈ 0.10 bar \Pi_p \approx 0.10\text{ bar} Π p ≈ 0.10 bar
Membrane water permeance: A w = 2.00 × 10 − 7 m 3 / ( m 2 ⋅ s ⋅ bar ) = 0.720 LMH/bar A_w = 2.00 \times 10^{-7}\text{ m}^3/(\text{m}^2\cdot\text{s}\cdot\text{bar}) = 0.720\text{ LMH/bar} A w = 2.00 × 1 0 − 7 m 3 / ( m 2 ⋅ s ⋅ bar ) = 0.720 LMH/bar
Membrane salt permeability: B s = 6.00 × 10 − 8 m/s = 0.216 LMH B_s = 6.00 \times 10^{-8}\text{ m/s} = 0.216\text{ LMH} B s = 6.00 × 1 0 − 8 m/s = 0.216 LMH
Calculate:
Net transmembrane driving pressure ( Δ P − Δ Π \Delta P - \Delta \Pi Δ P − ΔΠ ) in bar \text{bar} bar .
Pure water flux J w J_w J w in LMH \text{LMH} LMH and in m/s \text{m/s} m/s .
Permeate salt concentration C p C_p C p in mg/L \text{mg/L} mg/L .
Observed salt rejection R j R_j R j .
Solution: Δ P = P f − P p = 25.0 − 1.0 = 24.0 bar \Delta P = P_f - P_p = 25.0 - 1.0 = 24.0\text{ bar} Δ P = P f − P p = 25.0 − 1.0 = 24.0 bar Δ Π = Π f − Π p = 3.20 − 0.10 = 3.10 bar \Delta \Pi = \Pi_f - \Pi_p = 3.20 - 0.10 = 3.10\text{ bar} ΔΠ = Π f − Π p = 3.20 − 0.10 = 3.10 bar Net Driving Pressure = Δ P − Δ Π = 24.0 − 3.10 = 20.90 bar \text{Net Driving Pressure} = \Delta P - \Delta \Pi = 24.0 - 3.10 = \mathbf{20.90\text{ bar}} Net Driving Pressure = Δ P − ΔΠ = 24.0 − 3.10 = 20.90 bar
Water flux calculation: J w = A w ⋅ ( Δ P − Δ Π ) = ( 0.720 LMH/bar ) × 20.90 bar = 15.048 LMH J_w = A_w \cdot (\Delta P - \Delta \Pi) = (0.720\text{ LMH/bar}) \times 20.90\text{ bar} = \mathbf{15.048\text{ LMH}} J w = A w ⋅ ( Δ P − ΔΠ ) = ( 0.720 LMH/bar ) × 20.90 bar = 15.048 LMH J w = 15.048 L/(m 2 ⋅ h) 1 , 000 L/m 3 × 3 , 600 s/h = 4.180 × 10 − 6 m/s J_w = \frac{15.048\text{ L/(m}^2\cdot\text{h)}}{1,000\text{ L/m}^3 \times 3,600\text{ s/h}} = \mathbf{4.180 \times 10^{-6}\text{ m/s}} J w = 1 , 000 L/m 3 × 3 , 600 s/h 15.048 L/(m 2 ⋅ h) = 4.180 × 1 0 − 6 m/s
Permeate salt concentration: C p = C f ( B s J w + B s ) = 4 , 000.0 mg/L × ( 0.216 LMH 15.048 + 0.216 LMH ) = 4 , 000.0 × ( 0.216 15.264 ) = 56.60 mg/L C_p = C_f \left( \frac{B_s}{J_w + B_s} \right) = 4,000.0\text{ mg/L} \times \left( \frac{0.216\text{ LMH}}{15.048 + 0.216\text{ LMH}} \right) = 4,000.0 \times \left( \frac{0.216}{15.264} \right) = \mathbf{56.60\text{ mg/L}} C p = C f ( J w + B s B s ) = 4 , 000.0 mg/L × ( 15.048 + 0.216 LMH 0.216 LMH ) = 4 , 000.0 × ( 15.264 0.216 ) = 56.60 mg/L
Salt rejection: R j = 1 − C p C f = 1 − 56.60 4 , 000.0 = 1 − 0.01415 = 0.98585 ( 98.59 % ) R_j = 1 - \frac{C_p}{C_f} = 1 - \frac{56.60}{4,000.0} = 1 - 0.01415 = \mathbf{0.98585} \quad (\mathbf{98.59\%}) R j = 1 − C f C p = 1 − 4 , 000.0 56.60 = 1 − 0.01415 = 0.98585 ( 98.59% )
Example B: Batch Tray Dryer Sizing and Drying Time
A batch tray dryer processes a porous pharmaceutical cake containing m s = 400.0 kg m_s = 400.0\text{ kg} m s = 400.0 kg of bone-dry solid. The exposed drying surface area is A = 16.0 m 2 A = 16.0\text{ m}^2 A = 16.0 m 2 . The wet cake enters at an initial moisture content of x 1 = 0.200 x_1 = 0.200 x 1 = 0.200 ( 20.0 wt % 20.0\text{ wt}\% 20.0 wt % wet basis) and must be dried to a final moisture content of x 2 = 0.040 x_2 = 0.040 x 2 = 0.040 ( 4.0 wt % 4.0\text{ wt}\% 4.0 wt % wet basis).
Drying Data:
Constant drying rate: R c = 2.00 kg water/(m 2 ⋅ h) R_c = 2.00\text{ kg water/(m}^2\cdot\text{h)} R c = 2.00 kg water/(m 2 ⋅ h)
Critical moisture content: X c = 0.100 kg water/kg dry solid X_c = 0.100\text{ kg water/kg dry solid} X c = 0.100 kg water/kg dry solid
Equilibrium moisture content: X e q = 0.010 kg water/kg dry solid X_{eq} = 0.010\text{ kg water/kg dry solid} X e q = 0.010 kg water/kg dry solid
Calculate:
Initial dry-basis moisture X 1 X_1 X 1 and final dry-basis moisture X 2 X_2 X 2 .
Drying time in the constant rate period ( t c t_c t c ) in hours.
Drying time in the falling rate period ( t f t_f t f ) in hours.
Total batch drying time ( t t o t a l t_{total} t t o t a l ) in hours.
Solution: X 1 = x 1 1 − x 1 = 0.200 1 − 0.200 = 0.200 0.800 = 0.2500 kg/kg dry solid X_1 = \frac{x_1}{1 - x_1} = \frac{0.200}{1 - 0.200} = \frac{0.200}{0.800} = \mathbf{0.2500\text{ kg/kg dry solid}} X 1 = 1 − x 1 x 1 = 1 − 0.200 0.200 = 0.800 0.200 = 0.2500 kg/kg dry solid X 2 = x 2 1 − x 2 = 0.040 1 − 0.040 = 0.040 0.960 = 0.04167 kg/kg dry solid X_2 = \frac{x_2}{1 - x_2} = \frac{0.040}{1 - 0.040} = \frac{0.040}{0.960} = \mathbf{0.04167\text{ kg/kg dry solid}} X 2 = 1 − x 2 x 2 = 1 − 0.040 0.040 = 0.960 0.040 = 0.04167 kg/kg dry solid
Because X 1 ( 0.250 ) > X c ( 0.100 ) > X 2 ( 0.04167 ) X_1 (0.250) > X_c (0.100) > X_2 (0.04167) X 1 ( 0.250 ) > X c ( 0.100 ) > X 2 ( 0.04167 ) , drying spans both constant and falling rate regimes.
Constant rate drying time: t c = m s A ⋅ R c ( X 1 − X c ) = 400.0 kg ( 16.0 m 2 ) × ( 2.00 kg/(m 2 ⋅ h) ) × ( 0.2500 − 0.100 ) = 400.0 32.0 × 0.1500 = 1.875 hours t_c = \frac{m_s}{A \cdot R_c} (X_1 - X_c) = \frac{400.0\text{ kg}}{(16.0\text{ m}^2) \times (2.00\text{ kg/(m}^2\cdot\text{h)})} \times (0.2500 - 0.100) = \frac{400.0}{32.0} \times 0.1500 = \mathbf{1.875\text{ hours}} t c = A ⋅ R c m s ( X 1 − X c ) = ( 16.0 m 2 ) × ( 2.00 kg/(m 2 ⋅ h) ) 400.0 kg × ( 0.2500 − 0.100 ) = 32.0 400.0 × 0.1500 = 1.875 hours
Falling rate drying time: X c − X e q = 0.100 − 0.010 = 0.0900 X_c - X_{eq} = 0.100 - 0.010 = 0.0900 X c − X e q = 0.100 − 0.010 = 0.0900 X 2 − X e q = 0.04167 − 0.010 = 0.03167 X_2 - X_{eq} = 0.04167 - 0.010 = 0.03167 X 2 − X e q = 0.04167 − 0.010 = 0.03167 X c − X e q X 2 − X e q = 0.0900 0.03167 = 2.8418 \frac{X_c - X_{eq}}{X_2 - X_{eq}} = \frac{0.0900}{0.03167} = 2.8418 X 2 − X e q X c − X e q = 0.03167 0.0900 = 2.8418 ln ( 2.8418 ) = 1.04447 \ln(2.8418) = 1.04447 ln ( 2.8418 ) = 1.04447 t f = m s ( X c − X e q ) A ⋅ R c ln ( X c − X e q X 2 − X e q ) = 400.0 × 0.0900 32.0 × 1.04447 = 1.125 × 1.04447 = 1.175 hours t_f = \frac{m_s (X_c - X_{eq})}{A \cdot R_c} \ln\left( \frac{X_c - X_{eq}}{X_2 - X_{eq}} \right) = \frac{400.0 \times 0.0900}{32.0} \times 1.04447 = 1.125 \times 1.04447 = \mathbf{1.175\text{ hours}} t f = A ⋅ R c m s ( X c − X e q ) ln ( X 2 − X e q X c − X e q ) = 32.0 400.0 × 0.0900 × 1.04447 = 1.125 × 1.04447 = 1.175 hours
Total drying time: t t o t a l = t c + t f = 1.875 h + 1.175 h = 3.050 hours ( 3 h 3 min ) t_{total} = t_c + t_f = 1.875\text{ h} + 1.175\text{ h} = \mathbf{3.050\text{ hours}} \quad (3\text{ h } 3\text{ min}) t t o t a l = t c + t f = 1.875 h + 1.175 h = 3.050 hours ( 3 h 3 min )
- 6. Critical PE Exam Traps & Pitfalls
- Trap 1: Using Wet Basis Moisture in Drying Equations
The formula t c = ( m / ( A R c ) ) ( x 1 − x 2 ) t_c = (m / (A R_c)) (x_1 - x_2) t c = ( m / ( A R c )) ( x 1 − x 2 ) using wet-basis moisture x x x is completely wrong. Total mass changes as water evaporates, so m m m is not constant. You MUST use bone-dry solid mass m s m_s m s and dry-basis moistures X 1 , X c , X 2 X_1, X_c, X_2 X 1 , X c , X 2 .
Trap 2: Ignoring Osmotic Pressure Direction in Reverse Osmosis
In RO calculations, water flux is driven by Δ P − Δ Π \Delta P - \Delta \Pi Δ P − ΔΠ . If the applied hydraulic pressure does not exceed the osmotic pressure of the feed ( Δ P < Δ Π \Delta P < \Delta \Pi Δ P < ΔΠ ), water will flow backward (forward osmosis), diluting the feed. Always verify that Δ P > Δ Π \Delta P > \Delta \Pi Δ P > ΔΠ .
Trap 3: Assuming Salt Flux Increases with Applied Hydraulic Pressure
In reverse osmosis, salt transport ( J s = B s Δ C J_s = B_s \Delta C J s = B s Δ C ) is independent of applied hydraulic pressure Δ P \Delta P Δ P . Increasing pump discharge pressure increases pure water flux, which dilutes the permeate salt concentration and improves salt rejection. Never calculate an increased salt flux when Δ P \Delta P Δ P is raised.
Trap 4: Misinterpreting Solid Temperature During Drying
During the constant rate drying period, the solid surface is saturated with liquid and remains at the wet-bulb temperature ( T w b T_{wb} T w b ) of the drying air, NOT the dry-bulb temperature ( T d b T_{db} T d b ). Heat-sensitive materials can safely be dried using hot air during this period because evaporative cooling shields the product.