Study guide

12.4 Filtration, Crystallization, and Solid-Fluid Separations

PE Chemical Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the PE Chemical Exam How to Use This Guide and the NCEES Handbook

2 Chapter 1: Material Balances & Flowsheet Calculations

1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations

3 Chapter 2: Energy Balances & Thermochemistry

2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances

4 Chapter 3: Fluid Statics & Incompressible Pipe Flow

3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations

5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up

6 Chapter 5: Thermodynamic Laws & Fundamental Relations

5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations

7 Chapter 6: Real Gases & Equations of State

6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions

8 Chapter 7: Phase & Chemical Reaction Equilibria

7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation

9 Chapter 8: Heat Transfer Mechanisms & Conduction

8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange

10 Chapter 9: Heat Exchanger Design & Phase Change

9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances

11 Chapter 10: Mass Transfer Fundamentals & Diffusion

10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

12 Chapter 11: Distillation Operations

11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components

13 Chapter 12: Rate-Controlled & Equilibrium Separations

12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations

14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors

13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations

15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis

14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models

16 Chapter 15: Physical & Transport Properties of Fluids

15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles

17 Chapter 16: Materials of Construction & Corrosion

16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention

18 Chapter 17: Process Safety & Pressure Relief Systems

17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment

19 Chapter 18: Process Control & Engineering Economics

18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems

20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance

19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation

21 Chapter 20: Plant Operation, Reliability & Continuous Improvement

20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting

12.4 Filtration, Crystallization, and Solid-Fluid Separations

Key Takeaways Explain This Topic AI

Constant-pressure cake filtration linearizes as t / V = [ μ α c / ( 2 A 2 Δ P ) ] V + μ R m / ( A Δ P ) t/V = \left[ \mu \alpha c / (2 A^2 \Delta P) \right] V + \mu R_m / (A \Delta P) t / V = [ μα c / ( 2 A 2 Δ P ) ] V + μ R m ​ / ( A Δ P ) ; plotting (t/V) against (V) gives a straight line whose slope yields the specific cake resistance α \alpha α and whose intercept yields the medium resistance R m R_m R m ​ .

For an incompressible cake, doubling Δ P \Delta P Δ P halves the filtration time; for a fully compressible cake ( α = α 0 Δ P s \alpha = \alpha_0 \Delta P^{s} α = α 0 ​ Δ P s with s → 1 s \to 1 s → 1 ), raising Δ P \Delta P Δ P buys no increase in throughput because the cake simply consolidates.

Crystallizer yield must be computed on the hydrate basis: water of crystallization leaves with the crystals, concentrating the mother liquor, so treating a hydrate as anhydrous badly underestimates yield.

An ideal MSMPR crystallizer has population density n = n 0 exp ⁡ [ − L / ( G τ ) ] n = n^0 \exp[-L/(G\tau)] n = n 0 exp [ − L / ( G τ )] , dominant crystal size L D = 3 G τ L_D = 3 G \tau L D ​ = 3 G τ , and a fixed coefficient of variation of about 50% regardless of operating conditions.

The Lapple cut diameter d p c = 9 μ W / [ 2 π N e v i ( ρ p − ρ ) ] d_{pc} = \sqrt{9 \mu W / [2\pi N_e v_i (\rho_p - \rho)]} d p c ​ = 9 μ W / [ 2 π N e ​ v i ​ ( ρ p ​ − ρ )] ​ defines the particle size a cyclone collects with 50% efficiency, using an effective number of turns N e ≈ 5 N_e \approx 5 N e ​ ≈ 5 .

Last updated: September 2026

12.4 Filtration, Crystallization, and Solid-Fluid Separations

The NCEES specification lists Other separations (e.g., liquid-liquid, liquid-solid, gas-solid, extraction, drying, adsorption, filtration, membrane separations, crystallization) as a single subtopic under Mass Transfer Applications. Sections 12.2 and 12.3 covered extraction, adsorption, membranes, and drying. This section covers the solid-handling operations that complete the list, and which appear on the exam as short, highly numerical problems.

1. Cake Filtration Theory

Slurry flows through a septum; solids build a cake of increasing thickness whose resistance grows with the volume already filtered. Combining Darcy's law through the cake and medium gives the general filtration rate equation: d t d V = μ A Δ P ( α c V A + R m ) \frac{dt}{dV} = \frac{\mu}{A \Delta P} \left( \frac{\alpha c V}{A} + R_m \right) d V d t ​ = A Δ P μ ​ ( A α c V ​ + R m ​ )

  • Symbol Meaning Typical units
  • (V) Cumulative filtrate volume m 3 \text{m}^3 m 3
  • (A) Filter area m 2 \text{m}^2 m 2
  • Δ P \Delta P Δ P Pressure drop across cake + medium Pa \text{Pa} Pa
  • μ \mu μ Filtrate viscosity Pa ⋅ s \text{Pa}\cdot\text{s} Pa ⋅ s
  • (c) Mass of dry cake per volume of filtrate kg/m 3 \text{kg/m}^3 kg/m 3
  • α \alpha α Specific cake resistance m/kg \text{m/kg} m/kg
  • R m R_m R m ​ Medium resistance m − 1 \text{m}^{-1} m − 1

Constant-pressure operation. Holding Δ P \Delta P Δ P fixed and integrating from (V = 0): t V = ( μ α c 2 A 2 Δ P ) V + μ R m A Δ P \boxed{\ \frac{t}{V} = \left( \frac{\mu \alpha c}{2 A^2 \Delta P} \right) V + \frac{\mu R_m}{A \Delta P}\ } V t ​ = ( 2 A 2 Δ P μα c ​ ) V + A Δ P μ R m ​ ​ ​

This is the workhorse. Plot (t/V) versus (V); the data fall on a straight line. The slope gives α \alpha α and the intercept gives R m R_m R m ​ . The exam typically hands you the fitted line and asks for a time, a required area, or a scale-up.

Constant-rate operation. If instead a positive-displacement pump holds (dV/dt) constant, V = V ˙ t V = \dot{V}t V = V ˙ t and the required pressure rises linearly with time. Most industrial filtrations begin at constant rate (pump-limited) and switch to constant pressure once the pump reaches its discharge limit.

2. Cake Compressibility

Real cakes consolidate under load. The specific resistance follows: α = α 0 ( Δ P ) s \alpha = \alpha_0 (\Delta P)^{s} α = α 0 ​ ( Δ P ) s

where (s) is the compressibility index .

  • (s) Cake behavior Effect of doubling Δ P \Delta P Δ P
  • (0) Incompressible (sand, coarse crystals) Rate doubles; time halves
  • (0.2-0.8) Moderately compressible (most precipitates) Partial gain
  • → 1 \to 1 → 1 Highly compressible (gelatinous hydroxides, biomass) No gain at all

Substituting into the cake-dominated limit, the filtration rate scales as Δ P 1 − s \Delta P^{1-s} Δ P 1 − s . At (s = 1) the exponent is zero: squeezing harder simply collapses the pore structure by exactly as much as the extra driving force gains. The industrial answer for a highly compressible cake is a filter aid (diatomaceous earth precoat or body feed), which provides a rigid incompressible matrix, not a bigger pump.

3. Worked Example: Constant-Pressure Filtration

Problem. A plate-and-frame press operating at constant pressure yields the fitted relation t / V = 3.00 × 10 4 V + 1.20 × 10 3 t/V = 3.00 \times 10^4 V + 1.20 \times 10^3 t / V = 3.00 × 1 0 4 V + 1.20 × 1 0 3 , with (t) in seconds and (V) in m 3 \text{m}^3 m 3 . (a) How long to collect 0.50 m 3 0.50\text{ m}^3 0.50 m 3 of filtrate? (b) The cake is essentially incompressible; how long if Δ P \Delta P Δ P is doubled?

(a) Multiply through by (V): t = V [ 3.00 × 10 4 V + 1.20 × 10 3 ] = 0.50 [ ( 3.00 × 10 4 ) ( 0.50 ) + 1.20 × 10 3 ] t = V \left[ 3.00 \times 10^4 V + 1.20 \times 10^3 \right] = 0.50 \left[ (3.00\times10^4)(0.50) + 1.20\times10^3 \right] t = V [ 3.00 × 1 0 4 V + 1.20 × 1 0 3 ] = 0.50 [ ( 3.00 × 1 0 4 ) ( 0.50 ) + 1.20 × 1 0 3 ] t = 0.50 [ 15,000 + 1,200 ] = 0.50 ( 16,200 ) = 8,100 s = 2.25 h t = 0.50 \left[ 15{,}000 + 1{,}200 \right] = 0.50(16{,}200) = 8{,}100\text{ s} = 2.25\text{ h} t = 0.50 [ 15 , 000 + 1 , 200 ] = 0.50 ( 16 , 200 ) = 8 , 100 s = 2.25 h

(b) Both the slope and the intercept carry Δ P \Delta P Δ P in the denominator, and for an incompressible cake α \alpha α does not change. Doubling Δ P \Delta P Δ P halves both coefficients: t = 0.50 [ ( 1.50 × 10 4 ) ( 0.50 ) + 600 ] = 0.50 ( 8,100 ) = 4,050 s = 1.125 h t = 0.50 \left[ (1.50\times10^4)(0.50) + 600 \right] = 0.50(8{,}100) = 4{,}050\text{ s} = 1.125\text{ h} t = 0.50 [ ( 1.50 × 1 0 4 ) ( 0.50 ) + 600 ] = 0.50 ( 8 , 100 ) = 4 , 050 s = 1.125 h

Exactly half. Had the cake been fully compressible ((s = 1)), α \alpha α would have doubled along with Δ P \Delta P Δ P , the slope would have been unchanged, and the gain would have been confined to the small medium-resistance term.

Equipment note. A plate-and-frame press is batch, high-pressure, labor-intensive, and suited to low-throughput high-value solids. A rotary vacuum drum filter is continuous but limited to roughly 80 kPa 80\text{ kPa} 80 kPa of driving force by the vacuum; its capacity is set by the submergence fraction (fraction of the drum immersed, typically (0.2) to (0.35)) and the cycle time, since each drum revolution filters, washes, dries, and discharges.

4. Crystallization

Driving force. Crystallization requires supersaturation , generated by cooling, by evaporating solvent, by adding an antisolvent, or by reaction. Between the solubility curve and the metastable limit lies the metastable zone, where existing crystals grow but spontaneous nucleation does not occur. Good crystallizer operation stays inside that zone: nucleate once, then grow. Blow through the metastable limit and you get a shower of fines and an unfilterable product.

Yield with a hydrate — the classic exam problem.

Problem. 2,000 kg 2{,}000\text{ kg} 2 , 000 kg of a 30.0 wt % 30.0\text{ wt}\% 30.0 wt % MgSO 4 \text{MgSO}_4 MgSO 4 ​ solution is cooled to 20 ∘ C 20^\circ\text{C} 2 0 ∘ C , where solubility is 25.0 kg 25.0\text{ kg} 25.0 kg anhydrous MgSO 4 \text{MgSO}_4 MgSO 4 ​ per 100 kg 100\text{ kg} 100 kg water. Crystals form as MgSO 4 ⋅ 7 H 2 O \text{MgSO}_4 \cdot 7\text{H}_2\text{O} MgSO 4 ​ ⋅ 7 H 2 ​ O ((M = 246.5); anhydrous (M = 120.4)). Evaporation is negligible. Find the crystal yield.

Solution. Feed contains 600 kg 600\text{ kg} 600 kg MgSO 4 \text{MgSO}_4 MgSO 4 ​ and 1,400 kg 1{,}400\text{ kg} 1 , 400 kg water. Let (C) be kg of heptahydrate. The anhydrous fraction of the hydrate is (120.4/246.5 = 0.4884), so each kg of crystal removes 0.4884 kg 0.4884\text{ kg} 0.4884 kg MgSO 4 \text{MgSO}_4 MgSO 4 ​ and 0.5116 kg 0.5116\text{ kg} 0.5116 kg water. Saturating the mother liquor: 600 − 0.4884 C 1,400 − 0.5116 C = 0.250 \frac{600 - 0.4884C}{1{,}400 - 0.5116C} = 0.250 1 , 400 − 0.5116 C 600 − 0.4884 C ​ = 0.250 600 − 0.4884 C = 350 − 0.1279 C ⟹ 250 = 0.3606 C ⟹ C = 693 kg 600 - 0.4884C = 350 - 0.1279C \quad \Longrightarrow \quad 250 = 0.3606C \quad \Longrightarrow \quad C = 693\text{ kg} 600 − 0.4884 C = 350 − 0.1279 C ⟹ 250 = 0.3606 C ⟹ C = 693 kg

The trap. Ignoring water of crystallization gives 600 − C = 0.250 ( 1,400 ) 600 - C = 0.250(1{,}400) 600 − C = 0.250 ( 1 , 400 ) , so C = 250 kg C = 250\text{ kg} C = 250 kg — low by a factor of (2.8). Removing water with the crystals concentrates the remaining liquor and drives far more solute out of solution than the anhydrous balance predicts. Always check whether the crystal is a hydrate.

MSMPR population balance. For a mixed-suspension, mixed-product-removal crystallizer at steady state with size-independent growth rate (G) and residence time τ \tau τ : n ( L ) = n 0 exp ⁡ ⁣ ( − L G τ ) n(L) = n^0 \exp\!\left( -\frac{L}{G\tau} \right) n ( L ) = n 0 exp ( − G τ L ​ )

A semilog plot of population density (n) against size (L) is a straight line of slope − 1 / ( G τ ) -1/(G\tau) − 1/ ( G τ ) and intercept n 0 n^0 n 0 (the nuclei population density). Consequences worth memorizing:

Dominant (mass-weighted modal) size: L D = 3 G τ L_D = 3 G \tau L D ​ = 3 G τ . To grow bigger crystals, increase residence time or growth rate — nothing else in the ideal model matters.

Coefficient of variation: a fixed 50% for an ideal MSMPR, independent of (G), τ \tau τ , and supersaturation. A narrow distribution therefore cannot be achieved by tuning an MSMPR; it requires fines destruction, classified product removal, or seeded batch operation.

5. Leaching and Gas-Solid Separation

Leaching (solid-liquid extraction) recovers a solute from a solid matrix with a solvent — oilseed extraction with hexane, metal recovery from ore, sugar from beets. Stage calculations mirror liquid-liquid extraction, with one addition: each stage's underflow carries retained solution with the solids. The usual simplifying assumption is constant underflow , meaning each stage's exiting solids retain a fixed mass of solution per mass of inert solid, which makes the operating line straight and permits a McCabe-Thiele or Kremser construction.

Cyclones separate solids from gas by centrifugal action. The Lapple cut diameter — the size collected at 50% efficiency — is: d p c = 9 μ W 2 π N e v i ( ρ p − ρ ) d_{pc} = \sqrt{\frac{9 \mu W}{2 \pi N_e v_i (\rho_p - \rho)}} d p c ​ = 2 π N e ​ v i ​ ( ρ p ​ − ρ ) 9 μ W ​ ​

with (W) the inlet width, v i v_i v i ​ the inlet velocity, and N e N_e N e ​ the effective number of gas turns (conventionally N e ≈ 5 N_e \approx 5 N e ​ ≈ 5 for a standard high-efficiency cyclone).

Example. μ = 1.8 × 10 − 5 Pa ⋅ s \mu = 1.8\times10^{-5}\text{ Pa}\cdot\text{s} μ = 1.8 × 1 0 − 5 Pa ⋅ s , W = 0.10 m W = 0.10\text{ m} W = 0.10 m , v i = 15 m/s v_i = 15\text{ m/s} v i ​ = 15 m/s , N e = 5 N_e = 5 N e ​ = 5 , ρ p = 2,000 kg/m 3 \rho_p = 2{,}000\text{ kg/m}^3 ρ p ​ = 2 , 000 kg/m 3 , ρ = 1.2 kg/m 3 \rho = 1.2\text{ kg/m}^3 ρ = 1.2 kg/m 3 : d p c = 9 ( 1.8 × 10 − 5 ) ( 0.10 ) 2 π ( 5 ) ( 15 ) ( 1,998.8 ) = 1.62 × 10 − 5 9.42 × 10 5 = 1.72 × 10 − 11 = 4.1 × 10 − 6 m = 4.1 μ m d_{pc} = \sqrt{\frac{9(1.8\times10^{-5})(0.10)}{2\pi(5)(15)(1{,}998.8)}} = \sqrt{\frac{1.62\times10^{-5}}{9.42\times10^{5}}} = \sqrt{1.72\times10^{-11}} = 4.1\times10^{-6}\text{ m} = 4.1\ \mu\text{m} d p c ​ = 2 π ( 5 ) ( 15 ) ( 1 , 998.8 ) 9 ( 1.8 × 1 0 − 5 ) ( 0.10 ) ​ ​ = 9.42 × 1 0 5 1.62 × 1 0 − 5 ​ ​ = 1.72 × 1 0 − 11 ​ = 4.1 × 1 0 − 6 m = 4.1 μ m

Because d p c ∝ W / v i d_{pc} \propto \sqrt{W/v_i} d p c ​ ∝ W / v i ​ ​ , a smaller, faster cyclone collects finer particles — which is why high-efficiency service uses several small parallel cyclones rather than one large one, at the cost of higher pressure drop. Below roughly 5 μ m 5\ \mu\text{m} 5 μ m , cyclones become ineffective and a baghouse or electrostatic precipitator is required.