Study guide

12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria

PE Chemical Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the PE Chemical Exam How to Use This Guide and the NCEES Handbook

2 Chapter 1: Material Balances & Flowsheet Calculations

1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations

3 Chapter 2: Energy Balances & Thermochemistry

2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances

4 Chapter 3: Fluid Statics & Incompressible Pipe Flow

3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations

5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up

6 Chapter 5: Thermodynamic Laws & Fundamental Relations

5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations

7 Chapter 6: Real Gases & Equations of State

6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions

8 Chapter 7: Phase & Chemical Reaction Equilibria

7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation

9 Chapter 8: Heat Transfer Mechanisms & Conduction

8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange

10 Chapter 9: Heat Exchanger Design & Phase Change

9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances

11 Chapter 10: Mass Transfer Fundamentals & Diffusion

10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

12 Chapter 11: Distillation Operations

11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components

13 Chapter 12: Rate-Controlled & Equilibrium Separations

12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations

14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors

13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations

15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis

14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models

16 Chapter 15: Physical & Transport Properties of Fluids

15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles

17 Chapter 16: Materials of Construction & Corrosion

16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention

18 Chapter 17: Process Safety & Pressure Relief Systems

17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment

19 Chapter 18: Process Control & Engineering Economics

18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems

20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance

19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation

21 Chapter 20: Plant Operation, Reliability & Continuous Improvement

20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting

12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria

Key Takeaways Explain This Topic AI

Liquid-Liquid Extraction (LLE) separates mixtures based on relative chemical solubilities rather than vapor pressures, making it the preferred industrial process for heat-sensitive biomolecules, close-boiling isomers, and azeotropic mixtures.

Ternary phase equilibria are represented on equilateral or right-angled triangular diagrams containing a binodal solubility curve, two-phase immiscibility envelope, conjugate tie lines, and a plait point where extract and raffinate compositions merge.

The Lever-Arm Rule governs material balances across two-phase envelopes: the mixture point M lies on the tie line between extract E and raffinate R, with phase mass ratio E / R = distance(M, R) / distance(E, M).

Selectivity (separation factor beta = (y_A / y_B) / (x_A / x_B) = K_D,A / K_D,B) must substantially exceed 1.0 for a feasible extraction; when beta = 1.0, separation is thermodynamically impossible.

In countercurrent multistage extraction with mutually immiscible carrier and solvent, theoretical stages are evaluated analytically via the extraction Kremser equation with extraction factor E_ext = K_D * S / B.

Last updated: September 2026

12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria

When components in a liquid mixture have nearly identical boiling points, form close-boiling azeotropes, or degrade thermally at reboiler temperatures, distillation becomes economically unviable or physically impossible. Under these conditions, Liquid-Liquid Extraction (LLE) —also termed solvent extraction—is the separation method of choice. LLE exploits differences in the chemical structure and solubility of components between two partially miscible liquid phases.

Key industrial examples tested on the NCEES PE Chemical Exam include the extraction of aromatics (benzene, toluene, xylene) from aliphatic hydrocarbons using sulfolane, recovery of acetic acid from dilute aqueous streams using ethyl acetate or isopropyl ether, and extraction of antibiotics and active pharmaceutical ingredients (APIs) from fermentation broths.

1. Terminology and Basic Phase Equilibrium Definitions

An extraction system involves at least three distinct chemical components:

Solute ( A A A ) : The target species to be removed or recovered.

Carrier / Diluent ( B B B ) : The liquid component initially containing the solute in the feed stream.

Solvent ( S S S or C C C ) : The added extracting liquid that is immiscible or partially miscible with the carrier B B B , and possesses high chemical affinity for solute A A A .

The feed stream ( F F F ) containing A + B A + B A + B is contacted with solvent stream ( S S S ). The system separates into two liquid phases:

Extract ( E E E ) : The solvent-rich phase containing the extracted solute A A A and a minor amount of carrier B B B .

Raffinate ( R R R ) : The carrier-rich phase containing the residual, unextracted solute A A A and dissolved solvent S S S . Solvent Feed (S)

  • |
  • v
  • +-------------+
  • Feed (F) ->| EXTRACTION |-> Extract (E) [Solvent-Rich + Solute A]
  • [A + B] | COLUMN |
  • +-------------+
  • |
  • v
  • Raffinate (R) [Carrier-Rich + Residual A]
  • 1. Distribution Coefficient ( K D K_D K D ​ )

The distribution coefficient (also known as the partition coefficient) measures the equilibrium affinity of solute A A A for the extract phase relative to the raffinate phase: K D ≡ y A x A K_D \equiv \frac{y_A}{x_A} K D ​ ≡ x A ​ y A ​ ​

Where:

y A y_A y A ​ = mass or mole fraction of solute A A A in the extract phase.

x A x_A x A ​ = mass or mole fraction of solute A A A in the conjugate raffinate phase.

For an effective extraction, K D > 1.0 K_D > 1.0 K D ​ > 1.0 is highly desirable, as it minimizes the required solvent circulation rate. If K D < 1.0 K_D < 1.0 K D ​ < 1.0 , extraction is still possible but requires large solvent volumes ( S ≫ F S \gg F S ≫ F ).

2. Selectivity (Separation Factor, β \beta β )

Selectivity ( β \beta β ) measures the ability of solvent S S S to separate solute A A A from carrier B B B . It is directly analogous to relative volatility ( α \alpha α ) in distillation: β A / B ≡ y A / x A y B / x B = K D , A K D , B \beta_{A/B} \equiv \frac{y_A / x_A}{y_B / x_B} = \frac{K_{D,A}}{K_{D,B}} β A / B ​ ≡ y B ​ / x B ​ y A ​ / x A ​ ​ = K D , B ​ K D , A ​ ​

Where:

y B , x B y_B, x_B y B ​ , x B ​ = mass or mole fractions of carrier B B B in extract and raffinate phases, respectively.

K D , A , K D , B K_{D,A}, K_{D,B} K D , A ​ , K D , B ​ = distribution coefficients of solute A A A and carrier B B B .

Selectivity Criteria:

β > 1.0 \beta > 1.0 β > 1.0 : The solvent preferentially dissolves solute A A A over carrier B B B . Separation by extraction is feasible. Industrial systems typically target β ≥ 5 \beta \ge 5 β ≥ 5 to 10 10 10 .

β = 1.0 \beta = 1.0 β = 1.0 : The solvent dissolves A A A and B B B in exact proportion to their concentrations. Separation by extraction is thermodynamically impossible .

β < 1.0 \beta < 1.0 β < 1.0 : The solvent preferentially extracts carrier B B B rather than solute A A A .

2. Ternary Phase Diagrams: Equilateral and Right-Angled

Ternary liquid-liquid equilibria (LLE) are mapped using three-component phase diagrams governed by the Gibbs Phase Rule: F = C − P + 2 = 3 − 2 + 2 = 3 F = C - P + 2 = 3 - 2 + 2 = 3 F = C − P + 2 = 3 − 2 + 2 = 3 degrees of freedom. At fixed operating temperature and pressure, F = 1 F = 1 F = 1 , meaning specifying one liquid-phase composition uniquely fixes all other conjugate equilibrium compositions. Equilateral Triangle Right-Angled Triangle

  • Solute (A) Solute (A) ^
  • /\ |
  • / \ |\
  • / \ | \
  • / Dome \ | \ Dome
  • /--------\ | \
  • / Tie- \ | \
  • / Lines \ |-----\
  • / \ | \
  • Carrier (B) +----------------+ Solvent (S) Carrier (B) +-------+---> Solvent (S)
  • Equilateral Triangular Diagrams

Each vertex represents 100 % 100\% 100% purity of a pure component ( A A A , B B B , or S S S ).

The side opposite a vertex represents 0 % 0\% 0% of that component.

Composition lines run parallel to the edges. At any interior point, x A + x B + x S = 1.00 x_A + x_B + x_S = 1.00 x A ​ + x B ​ + x S ​ = 1.00 ( 100 % 100\% 100% ).

Right-Angled Triangular Diagrams

Right-angled diagrams plot solute mass fraction ( x A x_A x A ​ ) on the vertical y-axis and solvent mass fraction ( x S x_S x S ​ ) on the horizontal x-axis. The origin ( 0 , 0 ) (0,0) ( 0 , 0 ) represents 100 % 100\% 100% pure carrier B B B . The carrier fraction is determined by difference: x B = 1.0 − x A − x S x_B = 1.0 - x_A - x_S x B ​ = 1.0 − x A ​ − x S ​ . This format is widely used on computer screens and engineering tests because standard Cartesian axes can be read directly.

Anatomical Features of the Ternary Diagram

Binodal Curve (Solubility Envelope) : The dome-shaped boundary separating the single-phase homogeneous liquid region (outside the dome) from the two-phase heterogeneous region (inside the dome). Any overall mixture falling beneath the binodal curve spontaneously splits into two conjugate liquid phases.

Tie Lines : Straight lines connecting two equilibrium phases in thermodynamic contact inside the two-phase region. One end terminates at the Extract side of the binodal curve ( E E E ), while the other end terminates at the Raffinate side ( R R R ). Tie lines are generally non-horizontal and cannot cross each other.

Plait Point ( P P P ) : The critical point on the binodal curve where the tie lines shrink to zero length. At the plait point, the compositions and physical densities of the extract and raffinate phases become identical, and the interfacial tension vanishes.

3. The Lever-Arm Rule in Extraction

When two streams are mixed, or when an unstable mixture splits into two equilibrium phases, the overall material balance obeys the Inverse Lever-Arm Rule .

Total and Component Mass Balances

Mixing Feed ( F F F ) with Solvent ( S S S ) produces an overall combined mixture ( M M M ): M = F + S = E + R M = F + S = E + R M = F + S = E + R M ⋅ x A , M = F ⋅ x A , F + S ⋅ x A , S = E ⋅ y A , E + R ⋅ x A , R M \cdot x_{A,M} = F \cdot x_{A,F} + S \cdot x_{A,S} = E \cdot y_{A,E} + R \cdot x_{A,R} M ⋅ x A , M ​ = F ⋅ x A , F ​ + S ⋅ x A , S ​ = E ⋅ y A , E ​ + R ⋅ x A , R ​ M ⋅ x S , M = F ⋅ x S , F + S ⋅ x S , S = E ⋅ y S , E + R ⋅ x S , R M \cdot x_{S,M} = F \cdot x_{S,F} + S \cdot x_{S,S} = E \cdot y_{S,E} + R \cdot x_{S,R} M ⋅ x S , M ​ = F ⋅ x S , F ​ + S ⋅ x S , S ​ = E ⋅ y S , E ​ + R ⋅ x S , R ​

Geometric Interpretation on the Phase Diagram

The mixture point M M M must lie strictly on the straight line connecting F F F and S S S .

By the inverse lever-arm rule on line F − S F-S F − S : F S = M S ‾ F M ‾ \frac{F}{S} = \frac{\overline{MS}}{\overline{FM}} S F ​ = FM MS ​ F M = M S ‾ F S ‾ , S M = F M ‾ F S ‾ \frac{F}{M} = \frac{\overline{MS}}{\overline{FS}}, \quad \frac{S}{M} = \frac{\overline{FM}}{\overline{FS}} M F ​ = FS MS ​ , M S ​ = FS FM ​

If point M M M falls within the two-phase region, it splits along the unique equilibrium tie line passing through M M M , establishing conjugate phases E E E and R R R .

By the inverse lever-arm rule on tie line E − M − R E-M-R E − M − R : E R = M R ‾ E M ‾ \frac{E}{R} = \frac{\overline{MR}}{\overline{EM}} R E ​ = EM MR ​ E M = M R ‾ E R ‾ , R M = E M ‾ E R ‾ \frac{E}{M} = \frac{\overline{MR}}{\overline{ER}}, \quad \frac{R}{M} = \frac{\overline{EM}}{\overline{ER}} M E ​ = ER MR ​ , M R ​ = ER EM ​

Important

Lever-Arm Rule Direction:

The mass of a phase is proportional to the opposite line segment! For example, E E E is proportional to the segment between M M M and R R R ( M R ‾ \overline{MR} MR ), NOT the segment adjacent to E E E ( E M ‾ \overline{EM} EM ). Inverting this ratio is one of the most common calculation traps on the PE exam.

4. Multistage Countercurrent Extraction: Hunter-Nash Method

To achieve high solute recovery while minimizing solvent consumption, industrial extractors use multistage countercurrent cascades. Extract E1 <--- [Stage 1] <--- [Stage 2] <--- ... <--- [Stage N] <--- Solvent S

  • | | |
  • Feed F ---> [Stage 1] ---> [Stage 2] ---> ... ---> [Stage N] ---> Raffinate RN
  • Overall Cascade Balances and the Difference Point ( Δ \Delta Δ )

Overall mass balances across the entire N N N -stage cascade: F + S = E 1 + R N = M F + S = E_1 + R_N = M F + S = E 1 ​ + R N ​ = M

Rearranging shows that the difference in mass flow between adjacent countercurrent streams is constant across every stage in the column: Δ = F − E 1 = R N − S = R j − E j + 1 \Delta = F - E_1 = R_N - S = R_j - E_{j+1} Δ = F − E 1 ​ = R N ​ − S = R j ​ − E j + 1 ​

Where Δ \Delta Δ is the operating difference point (or pole point). Geometrically:

The line through F F F and E 1 E_1 E 1 ​ must pass through Δ \Delta Δ .

The line through R N R_N R N ​ and S S S must also pass through Δ \Delta Δ .

Therefore, point Δ \Delta Δ lies at the intersection of line F − E 1 F-E_1 F − E 1 ​ and line R N − S R_N-S R N ​ − S .

The Hunter-Nash Stepping Procedure

Plot feed point F F F , solvent point S S S , desired raffinate R N R_N R N ​ , and extract E 1 E_1 E 1 ​ .

Draw line F − E 1 F-E_1 F − E 1 ​ and line S − R N S-R_N S − R N ​ and extend them until they intersect at the difference point Δ \Delta Δ .

Step 1 (Equilibrium Tie Line): Starting at E 1 E_1 E 1 ​ , follow the tie line across the two-phase region to determine the raffinate leaving stage 1, R 1 R_1 R 1 ​ .

Step 2 (Operating Line through Δ \Delta Δ ): Connect R 1 R_1 R 1 ​ to the pole point Δ \Delta Δ . The intersection of line R 1 − Δ R_1-\Delta R 1 ​ − Δ with the extract side of the binodal curve locates E 2 E_2 E 2 ​ .

Subsequent Steps: Follow the tie line from E 2 E_2 E 2 ​ to find R 2 R_2 R 2 ​ , then draw line R 2 − Δ R_2-\Delta R 2 ​ − Δ to find E 3 E_3 E 3 ​ . Repeat until the calculated raffinate composition R j R_j R j ​ reaches or surpasses the design specification R N R_N R N ​ .

The total number of tie lines traversed equals the number of theoretical stages ( N N N ) .

Minimum Solvent Rate ( S m i n S_{min} S min ​ )

If the solvent rate is reduced, the mixture point M M M shifts toward F F F , moving the operating point Δ \Delta Δ closer to the binodal curve. The minimum solvent rate ( S m i n S_{min} S min ​ ) occurs when an operating line passing through Δ \Delta Δ coincides exactly with an equilibrium tie line that projects through the feed point F F F ( tie-line pinch ). At this condition, an infinite number of stages ( N → ∞ N \to \infty N → ∞ ) is required.

5. Immiscible Extraction and the Analytical Kremser Equation

When the carrier solvent ( B B B ) and extracting solvent ( S S S ) are virtually insoluble in one another (e.g., water and heavy hydrocarbons), the flow rates of carrier B B B and solvent S S S remain strictly constant through all stages.

Solute-Free Mass Ratios

Let:

B B B = mass flow rate of pure carrier liquid ( kg/h \text{kg/h} kg/h or lb/h \text{lb/h} lb/h ).

S S S = mass flow rate of pure extracting solvent ( kg/h \text{kg/h} kg/h or lb/h \text{lb/h} lb/h ).

X X X = solute-free mass ratio in raffinate: X = x A 1 − x A = mass solute A mass carrier B X = \frac{x_A}{1 - x_A} = \frac{\text{mass solute } A}{\text{mass carrier } B} X = 1 − x A ​ x A ​ ​ = mass carrier B mass solute A ​ .

Y Y Y = solute-free mass ratio in extract: Y = y A 1 − y A = mass solute A mass solvent S Y = \frac{y_A}{1 - y_A} = \frac{\text{mass solute } A}{\text{mass solvent } S} Y = 1 − y A ​ y A ​ ​ = mass solvent S mass solute A ​ .

The operating line is linear in solute-free coordinates: B ( X i n − X o u t ) = S ( Y o u t − Y i n ) B (X_{in} - X_{out}) = S (Y_{out} - Y_{in}) B ( X in ​ − X o u t ​ ) = S ( Y o u t ​ − Y in ​ ) Y = B S ( X − X o u t ) + Y i n Y = \frac{B}{S} (X - X_{out}) + Y_{in} Y = S B ​ ( X − X o u t ​ ) + Y in ​

If the equilibrium relationship is also linear ( Y = m ⋅ X = K D ′ ⋅ X Y = m \cdot X = K_D' \cdot X Y = m ⋅ X = K D ′ ​ ⋅ X ):

The Extraction Factor ( E e x t E_{ext} E e x t ​ ) E e x t ≡ m ⋅ S B = K D ′ ⋅ S B E_{ext} \equiv \frac{m \cdot S}{B} = \frac{K_D' \cdot S}{B} E e x t ​ ≡ B m ⋅ S ​ = B K D ′ ​ ⋅ S ​

Tip

Contrast with Absorption Factor:

Notice that in extraction, the equilibrium slope m m m ( K D K_D K D ​ ) is in the numerator ( E e x t = m S / B E_{ext} = m S / B E e x t ​ = m S / B ), whereas in gas absorption, m m m is in the denominator ( A = L / ( m G ) A = L / (m G) A = L / ( m G ) ). This is because in extraction, the extracting agent ( S S S ) receives solute from B B B , whereas in absorption, the liquid ( L L L ) scrubs solute from gas ( G G G ). For an effective countercurrent extraction cascade, E e x t > 1.0 E_{ext} > 1.0 E e x t ​ > 1.0 (typically 1.3 ≤ E e x t ≤ 2.0 1.3 \le E_{ext} \le 2.0 1.3 ≤ E e x t ​ ≤ 2.0 ).

Analytical Theoretical Stage Sizing

For a countercurrent cascade with pure entering solvent ( Y i n = 0 Y_{in} = 0 Y in ​ = 0 ): N = ln ⁡ [ ( X i n X o u t ) ( 1 − 1 E e x t ) + 1 E e x t ] ln ⁡ ( E e x t ) N = \frac{\ln\left[ \left( \frac{X_{in}}{X_{out}} \right) \left( 1 - \frac{1}{E_{ext}} \right) + \frac{1}{E_{ext}} \right]}{\ln(E_{ext})} N = ln ( E e x t ​ ) ln [ ( X o u t ​ X in ​ ​ ) ( 1 − E e x t ​ 1 ​ ) + E e x t ​ 1 ​ ] ​

6. Industrial Extraction Equipment Selection

Selecting extraction equipment requires balancing stage efficiency, residence time, liquid-liquid settling rates, and mechanical shear.

Equipment Type Operating Principle Major Advantages Key Limitations Best Applications

Mixer-Settler Discrete stirred tank followed by horizontal gravity settler decanter High stage efficiency ( > 90 − 95 % >90-95\% > 90 − 95% ); easily handles large flow rates and wide density differences High floor space footprint; large solvent inventory; high capital cost for many stages ( > 4 >4 > 4 ) Hydrometallurgical metals recovery (copper, uranium), petrochemical washes

Sieve Tray Column Unagitated vertical tower; light phase disperses through perforated plates Low capital cost; no moving parts; reliable for low stage counts ( 2 − 5 2-5 2 − 5 ) Low stage efficiency ( 20 − 30 % 20-30\% 20 − 30% ); prone to fouling; cannot handle low interfacial tension systems Simple petrochemical wash towers, caustic treating

Agitated Column (Scheibel, Karr, RDC) Rotating impellers alternate with wire mesh or baffle calming zones Compact vertical footprint; handles 10 − 30 10-30 10 − 30 stages in single shell; high volumetric efficiency Mechanical complexity; emulsion formation if agitation is excessive Pharmaceutical purification, fine chemicals, isomer separations

Pulsed Column Hydraulic pulse applied to liquid in perforated plate tower No internal rotating seals; excellent droplet dispersion; small holdup Requires external pulse generator; cavitation risks at high frequencies Nuclear fuel reprocessing (radiological containment), toxic systems

Centrifugal Extractor (Podbielniak) High-speed rotation generates 1 , 000 − 5 , 000 × g 1,000-5,000 \times g 1 , 000 − 5 , 000 × g centrifugal field Extremely low residence time (seconds); separates low density differences ( Δ ρ < 0.02 g/cm 3 \Delta \rho < 0.02\text{ g/cm}^3 Δ ρ < 0.02 g/cm 3 ) High capital and maintenance costs; limited liquid throughput Fermentation broth antibiotics (penicillin), thermally unstable pharmaceuticals

  • 7. Comprehensive Worked Numerical Example: Countercurrent Extraction of Pyridine
  • Problem Statement

A wastewater stream of F = 2 , 000.0 kg/h F = 2,000.0\text{ kg/h} F = 2 , 000.0 kg/h containing 25.0 wt % 25.0\text{ wt}\% 25.0 wt % pyridine ( A A A ) and 75.0 wt % 75.0\text{ wt}\% 75.0 wt % water ( B B B ) is to be treated in a countercurrent extraction cascade using pure benzene ( S S S ) at 25.0 ∘ C 25.0^\circ\text{C} 25. 0 ∘ C to reduce the pyridine content in the exiting raffinate to 1.50 wt % 1.50\text{ wt}\% 1.50 wt % (wet basis).

Thermodynamic & Process Data:

Water ( B B B ) and benzene ( S S S ) are mutually completely immiscible.

The equilibrium distribution of pyridine on a solute-free mass ratio basis is linear: Y = m ⋅ X = 0.80 ⋅ X ( K D ′ = 0.80 ) Y = m \cdot X = 0.80 \cdot X \quad (K_D' = 0.80) Y = m ⋅ X = 0.80 ⋅ X ( K D ′ ​ = 0.80 )

Pure benzene solvent is fed to the extractor ( Y i n = 0 Y_{in} = 0 Y in ​ = 0 ).

Calculate:

The mass flow rate of pure water carrier ( B B B ) and the initial solute ratio ( X i n X_{in} X in ​ ).

The required final solute ratio in the raffinate ( X o u t X_{out} X o u t ​ ).

The minimum solvent flow rate S m i n S_{min} S min ​ in kg/h \text{kg/h} kg/h .

The actual solvent rate S S S using a design margin of 1.40 × S m i n 1.40 \times S_{min} 1.40 × S min ​ .

The extraction factor E e x t E_{ext} E e x t ​ .

The outlet extract solute ratio ( Y o u t Y_{out} Y o u t ​ ) and total pyridine extracted in kg/h \text{kg/h} kg/h .

The required number of theoretical stages N N N using the Kremser extraction equation.

Step 1: Carrier Flow and Feed Solute Ratio B = F × ( 1 − x A , F ) = 2 , 000.0 kg/h × ( 1 − 0.250 ) = 1 , 500.0 kg/h of water B = F \times (1 - x_{A,F}) = 2,000.0\text{ kg/h} \times (1 - 0.250) = \mathbf{1,500.0\text{ kg/h of water}} B = F × ( 1 − x A , F ​ ) = 2 , 000.0 kg/h × ( 1 − 0.250 ) = 1 , 500.0 kg/h of water

Initial solute-free ratio in feed: X i n = x A , F 1 − x A , F = 0.250 0.750 = 0.3333 kg pyridine / kg water X_{in} = \frac{x_{A,F}}{1 - x_{A,F}} = \frac{0.250}{0.750} = \mathbf{0.3333\text{ kg pyridine / kg water}} X in ​ = 1 − x A , F ​ x A , F ​ ​ = 0.750 0.250 ​ = 0.3333 kg pyridine / kg water

Step 2: Target Raffinate Solute Ratio

The target raffinate concentration is x A , R = 0.0150 x_{A,R} = 0.0150 x A , R ​ = 0.0150 ( 1.50 wt % 1.50\text{ wt}\% 1.50 wt % ): X o u t = x A , R 1 − x A , R = 0.0150 1 − 0.0150 = 0.0150 0.9850 = 0.01523 kg pyridine / kg water X_{out} = \frac{x_{A,R}}{1 - x_{A,R}} = \frac{0.0150}{1 - 0.0150} = \frac{0.0150}{0.9850} = \mathbf{0.01523\text{ kg pyridine / kg water}} X o u t ​ = 1 − x A , R ​ x A , R ​ ​ = 1 − 0.0150 0.0150 ​ = 0.9850 0.0150 ​ = 0.01523 kg pyridine / kg water

Step 3: Minimum Solvent Rate ( S m i n S_{min} S min ​ )

At the minimum solvent rate ( N → ∞ N \to \infty N → ∞ ), the extract leaving stage 1 ( Y o u t ∗ Y_{out}^* Y o u t ∗ ​ ) reaches equilibrium with the incoming feed ( X i n X_{in} X in ​ ): Y o u t ∗ = m ⋅ X i n = 0.80 × 0.3333 = 0.26667 kg pyridine / kg benzene Y_{out}^* = m \cdot X_{in} = 0.80 \times 0.3333 = 0.26667\text{ kg pyridine / kg benzene} Y o u t ∗ ​ = m ⋅ X in ​ = 0.80 × 0.3333 = 0.26667 kg pyridine / kg benzene

Applying the overall solute balance at minimum solvent flow: B ( X i n − X o u t ) = S m i n ( Y o u t ∗ − Y i n ) B(X_{in} - X_{out}) = S_{min}(Y_{out}^* - Y_{in}) B ( X in ​ − X o u t ​ ) = S min ​ ( Y o u t ∗ ​ − Y in ​ ) S m i n = B ⋅ X i n − X o u t Y o u t ∗ − 0 = 1 , 500.0 × 0.3333 − 0.01523 0.26667 = 1 , 500.0 × 0.31810 0.26667 = 1 , 500.0 × 1.1929 = 1 , 789.3 kg/h S_{min} = B \cdot \frac{X_{in} - X_{out}}{Y_{out}^* - 0} = 1,500.0 \times \frac{0.3333 - 0.01523}{0.26667} = 1,500.0 \times \frac{0.31810}{0.26667} = 1,500.0 \times 1.1929 = \mathbf{1,789.3\text{ kg/h}} S min ​ = B ⋅ Y o u t ∗ ​ − 0 X in ​ − X o u t ​ ​ = 1 , 500.0 × 0.26667 0.3333 − 0.01523 ​ = 1 , 500.0 × 0.26667 0.31810 ​ = 1 , 500.0 × 1.1929 = 1 , 789.3 kg/h

Step 4: Actual Solvent Rate ( S S S )

Using S = 1.40 × S m i n S = 1.40 \times S_{min} S = 1.40 × S min ​ : S = 1.40 × 1 , 789.3 kg/h = 2 , 505.0 kg/h of benzene S = 1.40 \times 1,789.3\text{ kg/h} = \mathbf{2,505.0\text{ kg/h of benzene}} S = 1.40 × 1 , 789.3 kg/h = 2 , 505.0 kg/h of benzene

Step 5: Extraction Factor ( E e x t E_{ext} E e x t ​ ) E e x t = m ⋅ S B = 0.80 × 2 , 505.0 kg/h 1 , 500.0 kg/h = 2 , 004.0 1 , 500.0 = 1.336 E_{ext} = \frac{m \cdot S}{B} = \frac{0.80 \times 2,505.0\text{ kg/h}}{1,500.0\text{ kg/h}} = \frac{2,004.0}{1,500.0} = \mathbf{1.336} E e x t ​ = B m ⋅ S ​ = 1 , 500.0 kg/h 0.80 × 2 , 505.0 kg/h ​ = 1 , 500.0 2 , 004.0 ​ = 1.336

Because E e x t = 1.336 > 1.0 E_{ext} = 1.336 > 1.0 E e x t ​ = 1.336 > 1.0 , deep solute recovery is achieved without an internal equilibrium pinch.

Step 6: Outlet Extract Composition and Solute Removal

From the operating line balance: Y o u t = B S ( X i n − X o u t ) = 1 , 500.0 2 , 505.0 × ( 0.3333 − 0.01523 ) = 0.59880 × 0.31810 = 0.19048 kg/kg Y_{out} = \frac{B}{S} (X_{in} - X_{out}) = \frac{1,500.0}{2,505.0} \times (0.3333 - 0.01523) = 0.59880 \times 0.31810 = \mathbf{0.19048\text{ kg/kg}} Y o u t ​ = S B ​ ( X in ​ − X o u t ​ ) = 2 , 505.0 1 , 500.0 ​ × ( 0.3333 − 0.01523 ) = 0.59880 × 0.31810 = 0.19048 kg/kg

Total pyridine extracted: m ˙ A , e x t r a c t e d = B ( X i n − X o u t ) = 1 , 500.0 × ( 0.3333 − 0.01523 ) = 1 , 500.0 × 0.31810 = 477.15 kg/h \dot{m}_{A,extracted} = B(X_{in} - X_{out}) = 1,500.0 \times (0.3333 - 0.01523) = 1,500.0 \times 0.31810 = \mathbf{477.15\text{ kg/h}} m ˙ A , e x t r a c t e d ​ = B ( X in ​ − X o u t ​ ) = 1 , 500.0 × ( 0.3333 − 0.01523 ) = 1 , 500.0 × 0.31810 = 477.15 kg/h Recovery = 477.15 kg/h 500.0 kg/h × 100 % = 95.43 % \text{Recovery} = \frac{477.15\text{ kg/h}}{500.0\text{ kg/h}} \times 100\% = \mathbf{95.43\%} Recovery = 500.0 kg/h 477.15 kg/h ​ × 100% = 95.43%

Step 7: Number of Theoretical Stages ( N N N )

Using the Kremser extraction equation for Y i n = 0 Y_{in} = 0 Y in ​ = 0 : X i n X o u t = 0.3333 0.01523 = 21.884 \frac{X_{in}}{X_{out}} = \frac{0.3333}{0.01523} = 21.884 X o u t ​ X in ​ ​ = 0.01523 0.3333 ​ = 21.884 1 − 1 E e x t = 1 − 1 1.336 = 1 − 0.74850 = 0.25150 1 - \frac{1}{E_{ext}} = 1 - \frac{1}{1.336} = 1 - 0.74850 = 0.25150 1 − E e x t ​ 1 ​ = 1 − 1.336 1 ​ = 1 − 0.74850 = 0.25150

Evaluating the numerator argument: Arg = ( X i n X o u t ) ( 1 − 1 E e x t ) + 1 E e x t = ( 21.884 × 0.25150 ) + 0.74850 = 5.5038 + 0.74850 = 6.2523 \text{Arg} = \left( \frac{X_{in}}{X_{out}} \right) \left( 1 - \frac{1}{E_{ext}} \right) + \frac{1}{E_{ext}} = (21.884 \times 0.25150) + 0.74850 = 5.5038 + 0.74850 = 6.2523 Arg = ( X o u t ​ X in ​ ​ ) ( 1 − E e x t ​ 1 ​ ) + E e x t ​ 1 ​ = ( 21.884 × 0.25150 ) + 0.74850 = 5.5038 + 0.74850 = 6.2523 ln ⁡ ( Arg ) = ln ⁡ ( 6.2523 ) = 1.83295 \ln(\text{Arg}) = \ln(6.2523) = 1.83295 ln ( Arg ) = ln ( 6.2523 ) = 1.83295 ln ⁡ ( E e x t ) = ln ⁡ ( 1.336 ) = 0.28968 \ln(E_{ext}) = \ln(1.336) = 0.28968 ln ( E e x t ​ ) = ln ( 1.336 ) = 0.28968 N = 1.83295 0.28968 = 6.33 theoretical stages N = \frac{1.83295}{0.28968} = \mathbf{6.33\text{ theoretical stages}} N = 0.28968 1.83295 ​ = 6.33 theoretical stages

A standard design would specify an agitated column equivalent to 7 7 7 theoretical stages.

  • 8. Critical PE Exam Traps & Pitfalls
  • Trap 1: Inverting the Lever-Arm Rule Ratio

In phase split calculations, remember that the length of the segment opposite a phase corresponds to that phase's mass. On tie line E − M − R E-M-R E − M − R , the mass of extract is E = M ⋅ ( M R ‾ / E R ‾ ) E = M \cdot (\overline{MR} / \overline{ER}) E = M ⋅ ( MR / ER ) , and the mass of raffinate is R = M ⋅ ( E M ‾ / E R ‾ ) R = M \cdot (\overline{EM} / \overline{ER}) R = M ⋅ ( EM / ER ) . Swapping the numerator segments inverts the phase split, yielding catastrophic errors.

Trap 2: Forgetting Downstream Solvent Recovery Costs

Extraction does not produce a pure final product; it merely transfers the solute from one liquid phase into another. The extract must subsequently be separated (typically via distillation) to recover the solvent for recycle and isolate pure solute. On PE exam design evaluations, the most volatile or easiest-to-distill solvent is chosen to minimize reboiler duty.

Trap 3: Misidentifying the Plait Point

The plait point is NOT necessarily at the apex (top) of the binodal curve! The apex represents the maximum solute concentration of the two-phase dome, whereas the plait point is where the tie line length shrinks to zero. Depending on the mutual solubility of carrier and solvent, the plait point can lie on the left or right slope of the curve.

Trap 4: Confusing Extraction Factor E e x t E_{ext} E e x t ​ with Absorption Factor A A A

In gas absorption, A = L / ( m G ) A = L / (m G) A = L / ( m G ) , where m m m is in the denominator. In liquid extraction, E e x t = m S / B E_{ext} = m S / B E e x t ​ = m S / B , where m = K D m = K_D m = K D ​ is in the numerator . Applying the absorption definition to extraction will cause you to compute 1 / E e x t 1/E_{ext} 1/ E e x t ​ , incorrectly concluding that an operable system has pinched.