Study guide
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency
Key Takeaways Explain This Topic AI
The First Law for open steady-state flow systems couples thermal and shaft energy with fluid enthalpy via Q_dot - W_dot_s = sum [m_dot_out * (h + u^2/2 + gz)_out] - sum [m_dot_in * (h + u^2/2 + gz)_in], where W_dot_s > 0 denotes shaft work produced by the system (turbines) and W_dot_s < 0 denotes work consumed (compressors and pumps).
The Second Law of Thermodynamics dictates that spontaneous heat transfer occurs solely down temperature gradients and establishes that no cyclic heat engine can convert 100% of absorbed thermal energy into net mechanical work (Kelvin-Planck statement).
The theoretical Carnot efficiency eta_Carnot = 1 - (T_C / T_H) sets the absolute upper thermodynamic limit for any heat engine operating between thermal reservoirs at T_H and T_C, where both temperatures must strictly be expressed in absolute Kelvin or Rankine.
Refrigerators and heat pumps operate on reversed cycles characterized by coefficients of performance (COP); the ideal Carnot relations are COP_R = T_C / (T_H - T_C) and COP_HP = T_H / (T_H - T_C) = COP_R + 1.
The Second Law efficiency eta_II = eta_actual / eta_Carnot benchmarks real equipment against reversible performance, providing the definitive metric for identifying avoidable thermodynamic destruction across chemical plant utilities.
Last updated: September 2026
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency
Thermodynamics governs the direction, feasibility, and ultimate energy conversion limits of all chemical and physical processes. On the NCEES PE Chemical Exam , Thermodynamics is weighted at 11-17 of the 80 questions, of which 4-6 come from the Basic Thermodynamics subtopic that covers state functions, the first and second laws, and power cycles. Mastering open-system energy conservation, the directional constraints imposed by the Second Law, reversible Carnot limits, and real-cycle utility efficiencies is indispensable for rapid, error-free problem solving on exam day.
1. The First Law of Thermodynamics: Energy Conservation
The First Law states that energy cannot be created or destroyed; it can only change form. In chemical engineering applications, energy accounting must be formulated precisely for both closed non-flow systems and continuous open flow systems.
Closed Systems (Non-Flow)
For a fixed mass of fluid contained within a closed boundary (no mass crosses the system envelope): d U = δ Q − δ W dU = \delta Q - \delta W d U = δ Q − δ W
Integrating between State 1 and State 2: Δ U = Q − W \Delta U = Q - W Δ U = Q − W
Where:
Δ U = U 2 − U 1 \Delta U = U_2 - U_1 Δ U = U 2 − U 1 is the change in total internal energy ( kJ \text{kJ} kJ or Btu \text{Btu} Btu ).
Q Q Q is the net heat transferred across the system boundary into the fluid ( Q > 0 Q > 0 Q > 0 for heat added to the system, Q < 0 Q < 0 Q < 0 for heat rejected).
W W W is the net work done by the fluid on the surroundings ( W > 0 W > 0 W > 0 for work done by the system, such as gas expansion; W < 0 W < 0 W < 0 for work done on the system, such as gas compression).
For a reversible quasi-static process in a closed system, boundary work is evaluated as: W r e v = ∫ V 1 V 2 P d V W_{rev} = \int_{V_1}^{V_2} P \, dV W re v = ∫ V 1 V 2 P d V
Open Steady-State Flow Systems (Control Volumes)
In continuous chemical process plants, fluids flow continuously across unit operation boundaries. The macroscopic rate-based First Law energy balance across a control volume is: d ( m U ) c v d t = Q ˙ − W ˙ s + ∑ i n m ˙ i n ( h i n + u i n 2 2 + g z i n ) − ∑ o u t m ˙ o u t ( h o u t + u o u t 2 2 + g z o u t ) \frac{d(mU)_{cv}}{dt} = \dot{Q} - \dot{W}_s + \sum_{in} \dot{m}_{in} \left( h_{in} + \frac{u_{in}^2}{2} + g z_{in} \right) - \sum_{out} \dot{m}_{out} \left( h_{out} + \frac{u_{out}^2}{2} + g z_{out} \right) d t d ( m U ) c v = Q ˙ − W ˙ s + in ∑ m ˙ in ( h in + 2 u in 2 + g z in ) − o u t ∑ m ˙ o u t ( h o u t + 2 u o u t 2 + g z o u t )
At steady state , accumulation is zero ( d ( m U ) c v / d t = 0 d(mU)_{cv}/dt = 0 d ( m U ) c v / d t = 0 ). For process equipment where kinetic ( u 2 / 2 u^2/2 u 2 /2 ) and potential ( g z gz g z ) energy changes are negligible compared to thermal enthalpy changes, the balance reduces to the standard NCEES PE Chemical Reference Handbook formulation: Q ˙ − W ˙ s = Δ H ˙ = ∑ o u t m ˙ o u t h o u t − ∑ i n m ˙ i n h i n \dot{Q} - \dot{W}_s = \Delta \dot{H} = \sum_{out} \dot{m}_{out} h_{out} - \sum_{in} \dot{m}_{in} h_{in} Q ˙ − W ˙ s = Δ H ˙ = o u t ∑ m ˙ o u t h o u t − in ∑ m ˙ in h in
Sign Conventions and Equipment Simplifications
Shaft Work ( W ˙ s \dot{W}_s W ˙ s ) :
Power-producing devices (Turbines, Expanders) : Fluid expands and performs work on the shaft. W ˙ s > 0 \dot{W}_s > 0 W ˙ s > 0 . If adiabatic ( Q ˙ ≈ 0 \dot{Q} \approx 0 Q ˙ ≈ 0 ): W ˙ s = − Δ H ˙ = m ˙ ( h i n − h o u t ) \dot{W}_s = -\Delta \dot{H} = \dot{m} (h_{in} - h_{out}) W ˙ s = − Δ H ˙ = m ˙ ( h in − h o u t )
Power-consuming devices (Compressors, Pumps, Blowers) : External mechanical shaft work is delivered to the fluid. W ˙ s < 0 \dot{W}_s < 0 W ˙ s < 0 . The power consumed by the equipment is: W ˙ c o m p = − W ˙ s = Δ H ˙ = m ˙ ( h o u t − h i n ) \dot{W}_{comp} = -\dot{W}_s = \Delta \dot{H} = \dot{m} (h_{out} - h_{in}) W ˙ co m p = − W ˙ s = Δ H ˙ = m ˙ ( h o u t − h in )
Heat Exchangers, Reboilers, Condensers :
No shaft penetrates the shell or tube bundle ( W ˙ s = 0 \dot{W}_s = 0 W ˙ s = 0 ): Q ˙ = Δ H ˙ = m ˙ ( h o u t − h i n ) \dot{Q} = \Delta \dot{H} = \dot{m} (h_{out} - h_{in}) Q ˙ = Δ H ˙ = m ˙ ( h o u t − h in )
Throttling Valves and Porous Plugs :
Uninsulated expansion with no work and negligible heat transfer ( Q ˙ = 0 \dot{Q} = 0 Q ˙ = 0 , W ˙ s = 0 \dot{W}_s = 0 W ˙ s = 0 ): h i n = h o u t (Strictly Isenthalpic) h_{in} = h_{out} \quad \text{(Strictly Isenthalpic)} h in = h o u t (Strictly Isenthalpic)
2. The Second Law of Thermodynamics: Directionality and Quality of Energy
While the First Law mandates quantity conservation, it cannot predict whether an energy conversion process can spontaneously occur. The Second Law of Thermodynamics dictates the directional asymmetry of natural processes: work can always be completely converted into heat via friction, but heat cannot be completely converted into work in a continuous cycle.
Classical Second Law Statements
Kelvin-Planck Statement : It is impossible for any continuous device that operates on a thermodynamic cycle to receive heat from a single thermal reservoir and deliver a net amount of work to the surroundings. (A heat engine must always reject waste heat to a colder sink; 100% thermal efficiency is physically impossible.)
Clausius Statement : It is impossible to construct a cyclic device that operates in such a manner that its sole effect is the transfer of heat from a cooler body to a hotter body. (External work input is mandatory to drive refrigeration or heat pump cycles.)
The Clausius Inequality
For any closed system undergoing an arbitrary thermodynamic cycle: ∮ δ Q T b ≤ 0 \oint \frac{\delta Q}{T_b} \le 0 ∮ T b δ Q ≤ 0
Where T b T_b T b is the absolute thermodynamic temperature of the system boundary where heat transfer occurs.
Reversible Cycle : ∮ δ Q r e v T b = 0 \oint \frac{\delta Q_{rev}}{T_b} = 0 ∮ T b δ Q re v = 0 (defines the state function entropy, d S = ( δ Q / T ) r e v dS = (\delta Q / T)_{rev} d S = ( δ Q / T ) re v ).
Irreversible (Real) Cycle : ∮ δ Q T b < 0 \oint \frac{\delta Q}{T_b} < 0 ∮ T b δ Q < 0 .
Impossible Cycle : ∮ δ Q T b > 0 \oint \frac{\delta Q}{T_b} > 0 ∮ T b δ Q > 0 (violates the Second Law).
For an open flow system operating at steady state, the Second Law dictates that the total rate of entropy generation ( S ˙ g e n \dot{S}_{gen} S ˙ g e n ) within the control volume must be non-negative: S ˙ g e n = ∑ o u t m ˙ o u t s o u t − ∑ i n m ˙ i n s i n − ∑ j Q ˙ j T j ≥ 0 \dot{S}_{gen} = \sum_{out} \dot{m}_{out} s_{out} - \sum_{in} \dot{m}_{in} s_{in} - \sum_j \frac{\dot{Q}_j}{T_j} \ge 0 S ˙ g e n = o u t ∑ m ˙ o u t s o u t − in ∑ m ˙ in s in − j ∑ T j Q ˙ j ≥ 0
3. Heat Engines and the Carnot Cycle Limit
A heat engine is a thermodynamic cycle that absorbs thermal energy ( Q H Q_H Q H ) from a high-temperature heat source at absolute temperature T H T_H T H , converts a fraction of that heat into net mechanical work ( W n e t W_{net} W n e t ), and rejects the remaining waste heat ( Q C Q_C Q C ) to a low-temperature heat sink at absolute temperature T C T_C T C . [ High-Temperature Reservoir: T_H ]
- |
- | Q_H (Heat Absorbed)
- v
- +-----------------+
- | HEAT ENGINE | =====> W_net = Q_H - Q_C
- +-----------------+
- |
- | Q_C (Waste Heat Rejected)
- v
- [ Low-Temperature Reservoir: T_C ]
From the First Law applied to the cyclic heat engine ( Δ U c y c l e = 0 \Delta U_{cycle} = 0 Δ U cyc l e = 0 ): W n e t = Q H − Q C W_{net} = Q_H - Q_C W n e t = Q H − Q C
The thermal efficiency ( η t h \eta_{th} η t h ) of any heat engine is defined as the ratio of desired net work output to the expensive heat input: η t h = W n e t Q H = Q H − Q C Q H = 1 − Q C Q H \eta_{th} = \frac{W_{net}}{Q_H} = \frac{Q_H - Q_C}{Q_H} = 1 - \frac{Q_C}{Q_H} η t h = Q H W n e t = Q H Q H − Q C = 1 − Q H Q C
The Ideal Carnot Heat Engine
Nicolas Léonard Sadi Carnot demonstrated in 1824 that the maximum possible efficiency between two thermal reservoirs is achieved by a reversible cycle comprising four sequential operations:
Isothermal Expansion ( 1 → 2 1 \to 2 1 → 2 ) : Fluid absorbs heat Q H Q_H Q H reversibly from the source at constant temperature T H T_H T H .
Isentropic (Adiabatic Reversible) Expansion ( 2 → 3 2 \to 3 2 → 3 ) : Fluid expands without heat exchange, producing work while its temperature drops from T H T_H T H to T C T_C T C .
Isothermal Compression ( 3 → 4 3 \to 4 3 → 4 ) : Fluid rejects heat Q C Q_C Q C reversibly to the cold sink at constant temperature T C T_C T C .
Isentropic (Adiabatic Reversible) Compression ( 4 → 1 4 \to 1 4 → 1 ) : Fluid is compressed without heat exchange, consuming work while its temperature rises from T C T_C T C back to T H T_H T H .
Because the entire Carnot cycle is externally and internally reversible: Q C Q H = T C T H \frac{Q_C}{Q_H} = \frac{T_C}{T_H} Q H Q C = T H T C
Substituting this relation into the thermal efficiency equation gives the famous Carnot efficiency : η C a r n o t = 1 − T C T H = T H − T C T H \eta_{Carnot} = 1 - \frac{T_C}{T_H} = \frac{T_H - T_C}{T_H} η C a r n o t = 1 − T H T C = T H T H − T C
Important
The Absolute Temperature Rule: In the Carnot efficiency equation, T H T_H T H and T C T_C T C must strictly be expressed in absolute thermodynamic units : Kelvin ( K = ∘ C + 273.15 \text{K} = ^\circ\text{C} + 273.15 K = ∘ C + 273.15 ) or Rankine ( ∘ R = ∘ F + 459.67 ^\circ\text{R} = ^\circ\text{F} + 459.67 ∘ R = ∘ F + 459.67 ). Substituting temperatures in Celsius or Fahrenheit is the single most common calculation trap on the PE exam.
Carnot Principles and Second-Law Corollaries
No heat engine operating between two given thermal reservoirs can be more efficient than a reversible Carnot engine operating between the same reservoirs: η a c t u a l ≤ η C a r n o t \eta_{actual} \le \eta_{Carnot} η a c t u a l ≤ η C a r n o t .
All reversible engines operating between the same two thermal reservoirs possess the identical efficiency, completely independent of the working fluid (steam, helium, air, or organic hydrocarbons).
To maximize thermal efficiency, chemical engineers must either raise source temperature T H T_H T H (e.g., using superheated steam or gas turbine combustion) or lower sink temperature T C T_C T C (e.g., cooling water or ambient river heat sinks).
4. Reversed Carnot Cycles: Refrigerators and Heat Pumps
Operating a Carnot cycle in reverse creates a cyclic refrigeration or heat pump device. Work input ( W n e t , i n W_{net, in} W n e t , in ) is supplied to transport thermal energy from a low-temperature region ( T C T_C T C ) to a high-temperature region ( T H T_H T H ). [ Warm Space / Heat Sink: T_H ]
- ^
- | Q_H (Heat Delivered)
- +-----------------+
- W_in =======> | REVERSED CYCLE |
- +-----------------+
- ^
- | Q_C (Cooling Heat Absorbed)
- [ Cold Space / Refrigerated Zone: T_C ]
By First Law energy conservation: W n e t , i n = Q H − Q C W_{net, in} = Q_H - Q_C W n e t , in = Q H − Q C
Because efficiency η = Desired Output / Work Input \eta = \text{Desired Output} / \text{Work Input} η = Desired Output / Work Input would frequently exceed 100 % 100\% 100% , performance is quantified using the Coefficient of Performance (COP) .
Refrigerators
The engineering objective of a refrigerator is cooling—removing heat Q C Q_C Q C from a cold refrigerated space: C O P R = β = Cooling Effect Work Input = Q C W n e t , i n = Q C Q H − Q C COP_R = \beta = \frac{\text{Cooling Effect}}{\text{Work Input}} = \frac{Q_C}{W_{net, in}} = \frac{Q_C}{Q_H - Q_C} CO P R = β = Work Input Cooling Effect = W n e t , in Q C = Q H − Q C Q C
For a reversible Carnot refrigerator: C O P R , C a r n o t = T C T H − T C COP_{R, Carnot} = \frac{T_C}{T_H - T_C} CO P R , C a r n o t = T H − T C T C
Heat Pumps
The engineering objective of a heat pump is heating—delivering thermal energy Q H Q_H Q H to a warm space (such as a plant administrative building or distillation column preheater): C O P H P = γ = Heating Effect Work Input = Q H W n e t , i n = Q H Q H − Q C COP_{HP} = \gamma = \frac{\text{Heating Effect}}{\text{Work Input}} = \frac{Q_H}{W_{net, in}} = \frac{Q_H}{Q_H - Q_C} CO P H P = γ = Work Input Heating Effect = W n e t , in Q H = Q H − Q C Q H
For a reversible Carnot heat pump: C O P H P , C a r n o t = T H T H − T C COP_{HP, Carnot} = \frac{T_H}{T_H - T_C} CO P H P , C a r n o t = T H − T C T H
Fundamental Relationship Between C O P H P COP_{HP} CO P H P and C O P R COP_R CO P R
Comparing the two COP expressions reveals an exact mathematical identity: C O P H P = Q H W i n = Q C + W i n W i n = Q C W i n + 1 = C O P R + 1 COP_{HP} = \frac{Q_H}{W_{in}} = \frac{Q_C + W_{in}}{W_{in}} = \frac{Q_C}{W_{in}} + 1 = COP_R + 1 CO P H P = W in Q H = W in Q C + W in = W in Q C + 1 = CO P R + 1 C O P H P = C O P R + 1 COP_{HP} = COP_R + 1 CO P H P = CO P R + 1
Because C O P R > 0 COP_R > 0 CO P R > 0 , the theoretical and actual COP of a heat pump is always greater than unity ( C O P H P > 1 COP_{HP} > 1 CO P H P > 1 ). A heat pump delivers more thermal energy than the electrical shaft power consumed because it pumps existing ambient thermal energy into the heated zone.
5. Summary Table: Energy Conversion Cycles Across Chemical Utilities
Cycle Type Primary Objective Energy Governing Equation Ideal Carnot Performance Metric Typical Industrial Actual Range
Heat Engine (Steam Rankine / ORC) Net Power Generation ( W n e t W_{net} W n e t ) W n e t = Q H − Q C W_{net} = Q_H - Q_C W n e t = Q H − Q C η C a r n o t = 1 − T C T H \eta_{Carnot} = 1 - \frac{T_C}{T_H} η C a r n o t = 1 − T H T C η a c t u a l = 25 % − 45 % \eta_{actual} = 25\% - 45\% η a c t u a l = 25% − 45%
Refrigerator / Chiller Cooling Duty ( Q C Q_C Q C ) W i n = Q H − Q C W_{in} = Q_H - Q_C W in = Q H − Q C C O P R = T C T H − T C COP_{R} = \frac{T_C}{T_H - T_C} CO P R = T H − T C T C C O P a c t u a l = 2.0 − 5.0 COP_{actual} = 2.0 - 5.0 CO P a c t u a l = 2.0 − 5.0
Heat Pump Heating Duty ( Q H Q_H Q H ) W i n = Q H − Q C W_{in} = Q_H - Q_C W in = Q H − Q C C O P H P = T H T H − T C COP_{HP} = \frac{T_H}{T_H - T_C} CO P H P = T H − T C T H C O P a c t u a l = 3.0 − 6.0 COP_{actual} = 3.0 - 6.0 CO P a c t u a l = 3.0 − 6.0
Absorption Chiller Cooling via Waste Heat Q C = f ( Q H , Q g e n ) Q_C = f(Q_H, Q_{gen}) Q C = f ( Q H , Q g e n ) C O P a b s = ( 1 − T C T g e n ) ( T e v a p T C − T e v a p ) COP_{abs} = \left(1 - \frac{T_C}{T_{gen}}\right)\left(\frac{T_{evap}}{T_C - T_{evap}}\right) CO P ab s = ( 1 − T g e n T C ) ( T C − T e v a p T e v a p ) C O P a c t u a l = 0.6 − 1.4 COP_{actual} = 0.6 - 1.4 CO P a c t u a l = 0.6 − 1.4
6. Critical PE Exam Traps & Pitfalls
- Warning
- PE Exam Trap 1: Temperatures Not Converted to Absolute Scale
Calculating Carnot efficiency using Celsius or Fahrenheit produces catastrophic errors. For example, between 300 ∘ C 300^\circ\text{C} 30 0 ∘ C and 30 ∘ C 30^\circ\text{C} 3 0 ∘ C :
Incorrect (Celsius): η = 1 − 30 / 300 = 90.0 % \eta = 1 - 30/300 = 90.0\% η = 1 − 30/300 = 90.0%
Correct (Kelvin): η = 1 − ( 30 + 273.15 ) / ( 300 + 273.15 ) = 1 − 303.15 / 573.15 = 47.1 % \eta = 1 - (30 + 273.15)/(300 + 273.15) = 1 - 303.15 / 573.15 = 47.1\% η = 1 − ( 30 + 273.15 ) / ( 300 + 273.15 ) = 1 − 303.15/573.15 = 47.1% The distractor list on the exam will always include the value evaluated with raw Celsius or Fahrenheit!
- Warning
- PE Exam Trap 2: Conflating C O P R COP_R CO P R and C O P H P COP_{HP} CO P H P
If an exam question asks for the compressor power required for a chilling duty Q C Q_C Q C and you divide by C O P H P COP_{HP} CO P H P instead of C O P R COP_R CO P R , your calculated power will be too low by a factor of ( C O P R + 1 ) / C O P R (COP_R + 1) / COP_R ( CO P R + 1 ) / CO P R . Always identify whether the process requirement is heat removal ( Q C → C O P R Q_C \to COP_R Q C → CO P R ) or heat addition ( Q H → C O P H P Q_H \to COP_{HP} Q H → CO P H P ).
- Warning
- PE Exam Trap 3: Work Sign Convention in Open-System Energy Balances
The NCEES standard open-system First Law is Q ˙ − W ˙ s = Δ H ˙ \dot{Q} - \dot{W}_s = \Delta \dot{H} Q ˙ − W ˙ s = Δ H ˙ . When solving for a pump or compressor, the shaft work is negative ( W ˙ s < 0 \dot{W}_s < 0 W ˙ s < 0 ). If a compressor draws 50 kW 50\text{ kW} 50 kW of mechanical power, W ˙ s = − 50 kW \dot{W}_s = -50\text{ kW} W ˙ s = − 50 kW , resulting in Δ H ˙ = Q ˙ − ( − 50 kW ) = Q ˙ + 50 kW \Delta \dot{H} = \dot{Q} - (-50\text{ kW}) = \dot{Q} + 50\text{ kW} Δ H ˙ = Q ˙ − ( − 50 kW ) = Q ˙ + 50 kW . Do not double-invert signs.
- 7. Step-by-Step Worked Numerical Example: Waste Heat Organic Rankine Cycle (ORC)
- Problem Statement
A chemical plant produces high-temperature waste heat in a sulfur recovery unit (SRU) condenser. Waste heat is continuously available at a steady rate of Q ˙ H = 5.00 MW \dot{Q}_H = 5.00\text{ MW} Q ˙ H = 5.00 MW ( 5 , 000 kW 5,000\text{ kW} 5 , 000 kW ) at an effective source temperature of T H = 260.0 ∘ C T_H = 260.0^\circ\text{C} T H = 260. 0 ∘ C .
Plant engineers design an Organic Rankine Cycle (ORC) utilizing cyclopentane as the working fluid to recover this waste heat. The ORC condenser rejects heat to an industrial cooling tower water loop maintained at T C = 25.0 ∘ C T_C = 25.0^\circ\text{C} T C = 25. 0 ∘ C . The actual ORC unit delivers a net measured electrical power output of W ˙ a c t u a l = 1.450 MW \dot{W}_{actual} = 1.450\text{ MW} W ˙ a c t u a l = 1.450 MW ( 1 , 450 kW 1,450\text{ kW} 1 , 450 kW ).
Calculate:
The maximum theoretical Carnot thermal efficiency ( η C a r n o t \eta_{Carnot} η C a r n o t ) operating between these reservoirs.
The maximum theoretical shaft power ( W ˙ m a x \dot{W}_{max} W ˙ ma x ) that could be produced by a reversible heat engine.
The actual thermal efficiency ( η a c t u a l \eta_{actual} η a c t u a l ) of the installed ORC system.
The Second Law efficiency ( η I I \eta_{II} η II ) of the cycle.
The rate of waste heat rejected to the cooling tower loop ( Q ˙ C \dot{Q}_C Q ˙ C ) in megawatts.
The net rate of entropy generation ( S ˙ g e n \dot{S}_{gen} S ˙ g e n ) in the universe caused by the actual cycle operation.
- Step-by-Step Solution
- Step 1: Convert Temperatures to Absolute Thermodynamic Scale
High-temperature reservoir: T H = 260.0 ∘ C + 273.15 = 533.15 K T_H = 260.0^\circ\text{C} + 273.15 = 533.15\text{ K} T H = 260. 0 ∘ C + 273.15 = 533.15 K
Low-temperature reservoir: T C = 25.0 ∘ C + 273.15 = 298.15 K T_C = 25.0^\circ\text{C} + 273.15 = 298.15\text{ K} T C = 25. 0 ∘ C + 273.15 = 298.15 K
Step 2: Maximum Carnot Thermal Efficiency η C a r n o t = 1 − T C T H = 1 − 298.15 K 533.15 K = 1 − 0.55922 = 0.44078 (44.08%) \eta_{Carnot} = 1 - \frac{T_C}{T_H} = 1 - \frac{298.15\text{ K}}{533.15\text{ K}} = 1 - 0.55922 = \mathbf{0.44078\text{ (44.08\%)}} η C a r n o t = 1 − T H T C = 1 − 533.15 K 298.15 K = 1 − 0.55922 = 0.44078 (44.08%)
Step 3: Maximum Theoretical Shaft Power Output W ˙ m a x = η C a r n o t × Q ˙ H = 0.44078 × 5.000 MW = 2.2039 MW ≈ 2 , 204 kW \dot{W}_{max} = \eta_{Carnot} \times \dot{Q}_H = 0.44078 \times 5.000\text{ MW} = \mathbf{2.2039\text{ MW} \approx 2,204\text{ kW}} W ˙ ma x = η C a r n o t × Q ˙ H = 0.44078 × 5.000 MW = 2.2039 MW ≈ 2 , 204 kW
Step 4: Actual Thermal Efficiency η a c t u a l = W ˙ a c t u a l Q ˙ H = 1.450 MW 5.000 MW = 0.2900 (29.00%) \eta_{actual} = \frac{\dot{W}_{actual}}{\dot{Q}_H} = \frac{1.450\text{ MW}}{5.000\text{ MW}} = \mathbf{0.2900\text{ (29.00\%)}} η a c t u a l = Q ˙ H W ˙ a c t u a l = 5.000 MW 1.450 MW = 0.2900 (29.00%)
Step 5: Second Law Efficiency
The Second Law efficiency benchmarks the actual conversion against the thermodynamic ideal: η I I = η a c t u a l η C a r n o t = 0.2900 0.44078 = 0.6579 (65.79%) \eta_{II} = \frac{\eta_{actual}}{\eta_{Carnot}} = \frac{0.2900}{0.44078} = \mathbf{0.6579\text{ (65.79\%)}} η II = η C a r n o t η a c t u a l = 0.44078 0.2900 = 0.6579 (65.79%)
(The ORC captures 65.8 % 65.8\% 65.8% of the maximum power thermodynamically available from this temperature differential.)
Step 6: Waste Heat Rejection to Cooling Water
By First Law energy conservation across the cyclic ORC plant: Q ˙ C = Q ˙ H − W ˙ a c t u a l = 5.000 MW − 1.450 MW = 3.550 MW ( 3 , 550 kW ) \dot{Q}_C = \dot{Q}_H - \dot{W}_{actual} = 5.000\text{ MW} - 1.450\text{ MW} = \mathbf{3.550\text{ MW} \quad (3,550\text{ kW})} Q ˙ C = Q ˙ H − W ˙ a c t u a l = 5.000 MW − 1.450 MW = 3.550 MW ( 3 , 550 kW )
Step 7: Rate of Universe Entropy Generation
The universe comprises the heat source, the heat sink, and the cyclic heat engine. Because the engine operates cyclically, its internal entropy change over complete cycles is zero ( Δ S e n g i n e = 0 \Delta S_{engine} = 0 Δ S e n g in e = 0 ). Entropy changes occur only in the thermal reservoirs: S ˙ s o u r c e = − Q ˙ H T H = − 5 , 000 kW 533.15 K = − 9.3782 kW/K \dot{S}_{source} = -\frac{\dot{Q}_H}{T_H} = -\frac{5,000\text{ kW}}{533.15\text{ K}} = -9.3782\text{ kW/K} S ˙ so u rce = − T H Q ˙ H = − 533.15 K 5 , 000 kW = − 9.3782 kW/K S ˙ s i n k = + Q ˙ C T C = + 3 , 550 kW 298.15 K = + 11.9068 kW/K \dot{S}_{sink} = +\frac{\dot{Q}_C}{T_C} = +\frac{3,550\text{ kW}}{298.15\text{ K}} = +11.9068\text{ kW/K} S ˙ s ink = + T C Q ˙ C = + 298.15 K 3 , 550 kW = + 11.9068 kW/K
Total entropy generation rate: S ˙ g e n = S ˙ s o u r c e + S ˙ s i n k = − 9.3782 + 11.9068 = + 2.5286 kW/K \dot{S}_{gen} = \dot{S}_{source} + \dot{S}_{sink} = -9.3782 + 11.9068 = \mathbf{+2.5286\text{ kW/K}} S ˙ g e n = S ˙ so u rce + S ˙ s ink = − 9.3782 + 11.9068 = + 2.5286 kW/K
(Notice that S ˙ g e n > 0 \dot{S}_{gen} > 0 S ˙ g e n > 0 , strictly validating Second Law conformity. Reversible operation would produce S ˙ g e n = 0 \dot{S}_{gen} = 0 S ˙ g e n = 0 .)
Verify using the Gouy-Stodola theorem ( T 0 = T C = 298.15 K T_0 = T_C = 298.15\text{ K} T 0 = T C = 298.15 K ): W ˙ l o s t = T 0 S ˙ g e n = 298.15 K × 2.5286 kW/K = 753.9 kW = 0.7539 MW \dot{W}_{lost} = T_0 \dot{S}_{gen} = 298.15\text{ K} \times 2.5286\text{ kW/K} = 753.9\text{ kW} = 0.7539\text{ MW} W ˙ l os t = T 0 S ˙ g e n = 298.15 K × 2.5286 kW/K = 753.9 kW = 0.7539 MW W ˙ a c t u a l + W ˙ l o s t = 1.4500 MW + 0.7539 MW = 2.2039 MW = W ˙ m a x (Exact Closure!) \dot{W}_{actual} + \dot{W}_{lost} = 1.4500\text{ MW} + 0.7539\text{ MW} = 2.2039\text{ MW} = \dot{W}_{max} \quad \text{(Exact Closure!)} W ˙ a c t u a l + W ˙ l os t = 1.4500 MW + 0.7539 MW = 2.2039 MW = W ˙ ma x (Exact Closure!)