Study guide

7.1 Reinforced Concrete Design

PE Civil Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Overview & Discipline Selection

1.1 PE Civil Exam Structure and Format 1.2 Choosing Your PE Civil Discipline

2 Construction Operations & Materials

2.1 Earthwork Construction and Estimating 2.2 Construction Scheduling and Project Control 2.3 Material Quality Control and Testing

3 Temporary Structures & Safety

3.1 Temporary Structures and Shoring 3.2 Construction Safety and Health Regulations

4 Soil Properties & Subsurface Exploration

4.1 Subsurface Exploration and Laboratory Testing 4.2 Engineering Properties of Soils

5 Foundation Design & Slope Stability

5.1 Lateral Earth Pressures and Retaining Structures 5.2 Shallow and Deep Foundation Design 5.3 Slope Stability and Soil Stabilization

6 Structural Analysis & Loading

6.1 Structural Loadings and Load Paths 6.2 Structural Analysis Methods

7 Design of Structural Materials

7.1 Reinforced Concrete Design 7.2 Structural Steel Design 7.3 Timber and Masonry Design

8 Highway Geometric Design

8.1 Geometric Design of Highways 8.2 Pavement Design and Materials

9 Traffic Operations & Safety

9.1 Traffic Engineering and Capacity Analysis 9.2 Traffic Safety and Operations 9.3 Intersection and Corridor Planning

10 Hydraulics & Open Channel Flow

10.1 Fluid Mechanics and Hydraulics 10.2 Open Channel Flow

11 Hydrology & Environmental Systems

11.1 Hydrology and Stormwater Management 11.2 Water Supply and Wastewater Treatment

7.1 Reinforced Concrete Design

Key Takeaways Explain This Topic AI

Whitney stress block simplifies concrete compression with an equivalent rectangular stress of 0.85*f'c and depth a = beta_1 * c.

Beam design controls ductility by requiring net tensile strain epsilon_t >= 0.005 for a tension-controlled strength factor phi = 0.90.

Shear reinforcement stirrup spacing must be halved from d/2 (max 24 in) to d/4 (max 12 in) if Vs exceeds 4 * lambda * sqrt(f'c) * bw * d.

Tension development length ld incorporates multipliers such as 1.3 for top bars cast with >12 inches of concrete below them.

Short columns require longitudinal reinforcement ratios between 1% and 8% and tie spacing limited to the lesser of 16db, 48dt, or column width.

Last updated: July 2026

Reinforced Concrete Design per ACI 318

Reinforced concrete design on the PE Civil exam is governed by the American Concrete Institute (ACI) 318 standard. The exam tests your ability to apply the strength design method (also known as load and resistance factor design, or LRFD) to analyze and design flexural members, shear reinforcement, development lengths, and short columns. Understanding the fundamental assumptions, code limitations, and design equations of ACI 318 is critical for solving these problems quickly and accurately.

1. Flexural Design of Beams

The flexural design of reinforced concrete beams is based on the assumption of strain compatibility, where the strain in both the concrete and steel is directly proportional to their distance from the neutral axis. Under bending, the concrete in compression behaves nonlinearly, which ACI 318 simplifies using the rectangular Whitney stress block .

Whitney Stress Block Assumptions

The actual parabolic stress distribution in concrete is simplified by a rectangular block with an average stress of 0.85 f c ′ 0.85 f'_c 0.85 f c ′ ​ and a depth of a a a . The relationship between the depth of the stress block ( a a a ) and the distance from the extreme compression fiber to the neutral axis ( c c c ) is: a = β 1 c a = \beta_1 c a = β 1 ​ c

The parameter β 1 \beta_1 β 1 ​ is a reduction factor that depends on the compressive strength of the concrete ( f c ′ f'_c f c ′ ​ ):

For f c ′ ≤ 4 , 000 psi f'_c \le 4,000 \text{ psi} f c ′ ​ ≤ 4 , 000 psi : β 1 = 0.85 \beta_1 = 0.85 β 1 ​ = 0.85

For 4 , 000 psi < f c ′ < 8 , 000 psi 4,000 \text{ psi} < f'_c < 8,000 \text{ psi} 4 , 000 psi < f c ′ ​ < 8 , 000 psi : β 1 = 0.85 − 0.05 f c ′ − 4000 1000 \beta_1 = 0.85 - 0.05 \frac{f'_c - 4000}{1000} β 1 ​ = 0.85 − 0.05 1000 f c ′ ​ − 4000 ​

For f c ′ ≥ 8 , 000 psi f'_c \ge 8,000 \text{ psi} f c ′ ​ ≥ 8 , 000 psi : β 1 = 0.65 \beta_1 = 0.65 β 1 ​ = 0.65

Nominal and Design Moment Capacity

For a singly reinforced rectangular beam, the nominal moment capacity ( M n M_n M n ​ ) is determined by establishing horizontal force equilibrium ( C = T C = T C = T ):

  • Compressive force of concrete: C = 0.85 f c ′ a b C = 0.85 f'_c a b C = 0.85 f c ′ ​ ab
  • Tensile force of steel: T = A s f y T = A_s f_y T = A s ​ f y ​

Equating the forces yields the depth of the stress block: a = A s f y 0.85 f c ′ b a = \frac{A_s f_y}{0.85 f'_c b} a = 0.85 f c ′ ​ b A s ​ f y ​ ​

The nominal moment capacity is the tensile force multiplied by the internal lever arm: M n = A s f y ( d − a 2 ) M_n = A_s f_y \left(d - \frac{a}{2}\right) M n ​ = A s ​ f y ​ ( d − 2 a ​ )

Or in terms of the reinforcement ratio ( ρ = A s b d \rho = \frac{A_s}{bd} ρ = b d A s ​ ​ ): M n = ρ b d 2 f y ( 1 − 0.59 ρ f y f c ′ ) M_n = \rho b d^2 f_y \left(1 - 0.59 \rho \frac{f_y}{f'_c}\right) M n ​ = ρ b d 2 f y ​ ( 1 − 0.59 ρ f c ′ ​ f y ​ ​ )

The design moment capacity is ϕ M n \phi M_n ϕ M n ​ , where the strength reduction factor ( ϕ \phi ϕ ) depends on the net tensile strain ( ϵ t \epsilon_t ϵ t ​ ) in the extreme tension steel layer:

Tension-controlled ( ϵ t ≥ 0.005 \epsilon_t \ge 0.005 ϵ t ​ ≥ 0.005 ): ϕ = 0.90 \phi = 0.90 ϕ = 0.90

Compression-controlled ( ϵ t ≤ 0.002 \epsilon_t \le 0.002 ϵ t ​ ≤ 0.002 ): ϕ = 0.65 \phi = 0.65 ϕ = 0.65 (for tied members) or ϕ = 0.75 \phi = 0.75 ϕ = 0.75 (for spiral members)

Transition zone ( 0.002 < ϵ t < 0.005 0.002 < \epsilon_t < 0.005 0.002 < ϵ t ​ < 0.005 ): ϕ = 0.65 + 0.25 ϵ t − 0.002 0.003 \phi = 0.65 + 0.25 \frac{\epsilon_t - 0.002}{0.003} ϕ = 0.65 + 0.25 0.003 ϵ t ​ − 0.002 ​ (for tied members)

The net tensile strain is computed from the strain diagram using the concrete compressive strain limit ( ϵ c u = 0.003 \epsilon_{cu} = 0.003 ϵ c u ​ = 0.003 ): ϵ t = 0.003 ( d − c c ) \epsilon_t = 0.003 \left(\frac{d - c}{c}\right) ϵ t ​ = 0.003 ( c d − c ​ )

Flexural Design Limits

To ensure ductile failure, ACI 318 limits the maximum reinforcement and establishes a minimum reinforcement ratio to prevent sudden collapse upon concrete cracking. The minimum steel area ( A s , m i n A_{s,min} A s , min ​ ) is the greater of: A s , m i n = 3 f c ′ f y b w d and 200 f y b w d A_{s,min} = \frac{3 \sqrt{f'_c}}{f_y} b_w d \quad \text{and} \quad \frac{200}{f_y} b_w d A s , min ​ = f y ​ 3 f c ′ ​ ​ ​ b w ​ d and f y ​ 200 ​ b w ​ d

ACI 318 transitioned from using ρ m a x \rho_{max} ρ ma x ​ in older editions to enforcing that the net tensile strain ϵ t \epsilon_t ϵ t ​ must be at least 0.004 0.004 0.004 for non-prestressed flexural members. Sections with ϵ t < 0.004 \epsilon_t < 0.004 ϵ t ​ < 0.004 are not permitted unless compression reinforcement is added.

Step-by-Step Beam Flexural Design Procedure

When designing a rectangular beam for flexure on the PE exam, follow these systematic steps:

Determine Factored Design Load ( M u M_u M u ​ ) : Use ACI 318 load combinations (e.g., 1.2 D + 1.6 L 1.2D + 1.6L 1.2 D + 1.6 L ).

Calculate Required Capacity : If beam dimensions ( b b b and d d d ) are known, calculate the required nominal capacity under the assumption of a tension-controlled section ( ϕ = 0.90 \phi = 0.90 ϕ = 0.90 ): R n = M u ϕ b d 2 R_n = \frac{M_u}{\phi b d^2} R n ​ = ϕ b d 2 M u ​ ​

Calculate Reinforcement Ratio ( ρ \rho ρ ) : ρ = 0.85 f c ′ f y ( 1 − 1 − 2 R n 0.85 f c ′ ) \rho = \frac{0.85 f'_c}{f_y} \left( 1 - \sqrt{1 - \frac{2 R_n}{0.85 f'_c}} \right) ρ = f y ​ 0.85 f c ′ ​ ​ ( 1 − 1 − 0.85 f c ′ ​ 2 R n ​ ​ ​ )

Determine Steel Area ( A s A_s A s ​ ) : A s = ρ b d A_s = \rho b d A s ​ = ρ b d .

Verify Limits : Ensure A s ≥ A s , m i n A_s \ge A_{s,min} A s ​ ≥ A s , min ​ . Verify that the net tensile strain ϵ t ≥ 0.005 \epsilon_t \ge 0.005 ϵ t ​ ≥ 0.005 to confirm that the strength reduction factor ϕ = 0.90 \phi = 0.90 ϕ = 0.90 is valid. If ϵ t < 0.005 \epsilon_t < 0.005 ϵ t ​ < 0.005 , the beam must be resized or designed with compression steel (doubly reinforced).

Parameter Description Typical Value range

f c ′ f'_c f c ′ ​ Concrete compressive strength 3 , 000 psi − 6 , 000 psi 3,000 \text{ psi} - 6,000 \text{ psi} 3 , 000 psi − 6 , 000 psi

f y f_y f y ​ Yield strength of reinforcement 60 , 000 psi (Grade 60) 60,000 \text{ psi} \text{ (Grade 60)} 60 , 000 psi (Grade 60)

  • β 1 \beta_1 β 1 ​ Stress block depth factor 0.65 − 0.85 0.65 - 0.85 0.65 − 0.85
  • ϕ \phi ϕ Strength reduction factor 0.65 − 0.90 0.65 - 0.90 0.65 − 0.90
  • 2. Shear Reinforcement (Stirrups)

Concrete members are susceptible to diagonal tension cracks caused by shear. Because concrete is weak in tension, steel shear reinforcement (typically in the form of vertical stirrups ) is provided to carry the excess shear.

Nominal Shear Capacity

The total design shear strength ( ϕ V n \phi V_n ϕ V n ​ ) must equal or exceed the factored shear force ( V u V_u V u ​ ) at the critical section (located at a distance d d d from the support face): V u ≤ ϕ V n = ϕ ( V c + V s ) V_u \le \phi V_n = \phi (V_c + V_s) V u ​ ≤ ϕ V n ​ = ϕ ( V c ​ + V s ​ )

Where the shear reduction factor ϕ \phi ϕ is 0.75 0.75 0.75 .

The concrete shear strength ( V c V_c V c ​ ) for members subjected to shear and flexure is: V c = 2 λ f c ′ b w d V_c = 2 \lambda \sqrt{f'_c} b_w d V c ​ = 2 λ f c ′ ​ ​ b w ​ d

Where λ \lambda λ is the lightweight concrete factor (1.0 for normal weight, 0.85 for sand-lightweight, 0.75 for all-lightweight).

Steel Shear Capacity and Stirrup Spacing

If the factored shear V u V_u V u ​ exceeds the concrete shear strength ( V u > ϕ V c V_u > \phi V_c V u ​ > ϕ V c ​ ), stirrups are required. The required steel shear capacity ( V s V_s V s ​ ) is: V s = V u ϕ − V c V_s = \frac{V_u}{\phi} - V_c V s ​ = ϕ V u ​ ​ − V c ​

The spacing ( s s s ) of vertical stirrups with area A v A_v A v ​ (where A v = 2 × A b a r A_v = 2 \times A_{bar} A v ​ = 2 × A ba r ​ for a standard double-leg stirrup) is: s = A v f y t d V s s = \frac{A_v f_{yt} d}{V_s} s = V s ​ A v ​ f y t ​ d ​

ACI Spacing and Minimum Area Limits

Even if the calculated shear is low, minimum shear reinforcement ( A v , m i n A_{v,min} A v , min ​ ) is required if V u > 0.5 ϕ V c V_u > 0.5 \phi V_c V u ​ > 0.5 ϕ V c ​ . The minimum shear reinforcement spacing is limited by: s m a x = A v f y t 0.75 f c ′ b w and s m a x = A v f y t 50 b w s_{max} = \frac{A_v f_{yt}}{0.75 \sqrt{f'_c} b_w} \quad \text{and} \quad s_{max} = \frac{A_v f_{yt}}{50 b_w} s ma x ​ = 0.75 f c ′ ​ ​ b w ​ A v ​ f y t ​ ​ and s ma x ​ = 50 b w ​ A v ​ f y t ​ ​

Furthermore, maximum stirrup spacing limits are based on the magnitude of V s V_s V s ​ :

If V s ≤ 4 f c ′ b w d V_s \le 4 \sqrt{f'_c} b_w d V s ​ ≤ 4 f c ′ ​ ​ b w ​ d : s m a x = min ⁡ ( d / 2 , 24 inches ) s_{max} = \min(d/2, 24 \text{ inches}) s ma x ​ = min ( d /2 , 24 inches )

If V s > 4 f c ′ b w d V_s > 4 \sqrt{f'_c} b_w d V s ​ > 4 f c ′ ​ ​ b w ​ d : s m a x = min ⁡ ( d / 4 , 12 inches ) s_{max} = \min(d/4, 12 \text{ inches}) s ma x ​ = min ( d /4 , 12 inches )

If V s > 8 f c ′ b w d V_s > 8 \sqrt{f'_c} b_w d V s ​ > 8 f c ′ ​ ​ b w ​ d : The section must be resized (exceeds allowable limits).

Step-by-Step Shear Design Procedure

To design shear stirrups, follow this workflow:

Calculate V u V_u V u ​ at the Critical Section : The critical section is located at distance d d d from the face of the support.

Calculate Concrete Shear Capacity ( ϕ V c \phi V_c ϕ V c ​ ) : ϕ V c = 0.75 × 2 λ f c ′ b w d \phi V_c = 0.75 \times 2 \lambda \sqrt{f'_c} b_w d ϕ V c ​ = 0.75 × 2 λ f c ′ ​ ​ b w ​ d

Evaluate Shear Reinforcement Requirements :

Case A: V u ≤ 0.5 ϕ V c V_u \le 0.5 \phi V_c V u ​ ≤ 0.5 ϕ V c ​ : No stirrups are required.

Case B: 0.5 ϕ V c < V u ≤ ϕ V c 0.5 \phi V_c < V_u \le \phi V_c 0.5 ϕ V c ​ < V u ​ ≤ ϕ V c ​ : Provide minimum shear reinforcement ( A v , m i n A_{v,min} A v , min ​ ) at spacing s m a x s_{max} s ma x ​ .

Case C: V u > ϕ V c V_u > \phi V_c V u ​ > ϕ V c ​ : Calculate required steel shear capacity V s V_s V s ​ and design stirrup spacing s s s . Ensure s ≤ s m a x s \le s_{max} s ≤ s ma x ​ .

3. Development Length

For reinforced concrete to act monolithically, there must be a complete bond transfer between the steel and concrete. The development length ( l d l_d l d ​ ) is the shortest embedment length required to develop the yield strength of the reinforcing bar.

Tension Development Length

For deformed bars in tension, ACI 318 provides a general formula: l d = ( 3 40 f y λ f c ′ ψ t ψ e ψ s ψ g ( c b + K t r d b ) ) d b l_d = \left( \frac{3}{40} \frac{f_y}{\lambda \sqrt{f'_c}} \frac{\psi_t \psi_e \psi_s \psi_g}{\left(\frac{c_b + K_{tr}}{d_b}\right)} \right) d_b l d ​ = ​ 40 3 ​ λ f c ′ ​ ​ f y ​ ​ ( d b ​ c b ​ + K t r ​ ​ ) ψ t ​ ψ e ​ ψ s ​ ψ g ​ ​ ​ d b ​

Where the modification factors are defined as:

Casting position factor ( ψ t \psi_t ψ t ​ ): 1.3 for "top bars" (horizontal reinforcement with more than 12 inches of fresh concrete cast below them) and 1.0 for other bars.

Coating factor ( ψ e \psi_e ψ e ​ ): 1.5 for epoxy-coated bars with cover less than 3 d b 3d_b 3 d b ​ or clear spacing less than 6 d b 6d_b 6 d b ​ , 1.2 for other epoxy-coated bars, and 1.0 for uncoated/zinc-coated bars. (Note: ψ t × ψ e ≤ 1.7 \psi_t \times \psi_e \le 1.7 ψ t ​ × ψ e ​ ≤ 1.7 ).

Size factor ( ψ s \psi_s ψ s ​ ): 0.8 for #6 and smaller bars, and 1.0 for #7 and larger bars.

Grade factor ( ψ g \psi_g ψ g ​ ): 1.0 for Grade 60 steel, 1.15 for Grade 80, and 1.3 for Grade 100.

Spacing/Cover factor ( c b c_b c b ​ ): The smaller of the distance from the center of the bar to the nearest concrete surface or half the center-to-center spacing of the bars.

Transverse reinforcement index ( K t r K_{tr} K t r ​ ): Represents the contribution of stirrups crossing potential splitting planes. For typical PE exam problems, K t r K_{tr} K t r ​ can be conservatively taken as 0.

The ratio c b + K t r d b \frac{c_b + K_{tr}}{d_b} d b ​ c b ​ + K t r ​ ​ must not exceed 2.5. The minimum development length in tension is always 12 inches.

Hook Development Length

When space is limited, standard 90 ∘ 90^\circ 9 0 ∘ or 180 ∘ 180^\circ 18 0 ∘ hooks are used. The development length for a standard hook in tension ( l d h l_{dh} l d h ​ ) is: l d h = ( f y ψ e ψ c ψ r 50 λ f c ′ ) d b ≥ max ⁡ ( 8 d b , 6 inches ) l_{dh} = \left( \frac{f_y \psi_e \psi_c \psi_r}{50 \lambda \sqrt{f'_c}} \right) d_b \ge \max(8d_b, 6 \text{ inches}) l d h ​ = ( 50 λ f c ′ ​ ​ f y ​ ψ e ​ ψ c ​ ψ r ​ ​ ) d b ​ ≥ max ( 8 d b ​ , 6 inches )

Where ψ e \psi_e ψ e ​ is the coating factor (1.2 for epoxy, 1.0 for uncoated), ψ c \psi_c ψ c ​ is the cover factor (0.7 if side cover is ≥ 2.5 \ge 2.5 ≥ 2.5 inches and end cover is ≥ 2.0 \ge 2.0 ≥ 2.0 inches), and ψ r \psi_r ψ r ​ is the confining reinforcement factor (typically 1.0 or 0.8 if enclosed by ties/stirrups).

4. Design of Short Columns

A column is considered a short column if its strength is governed solely by the cross-sectional materials and dimensions, without being reduced by slenderness effects.

Pure Axial Compressive Capacity

Under ACI 318, the nominal axial strength of a column under zero eccentricity ( P 0 P_0 P 0 ​ ) accounts for the concrete area and steel area: P 0 = 0.85 f c ′ ( A g − A s t ) + f y A s t P_0 = 0.85 f'_c (A_g - A_{st}) + f_y A_{st} P 0 ​ = 0.85 f c ′ ​ ( A g ​ − A s t ​ ) + f y ​ A s t ​

Where A g A_g A g ​ is the gross area of the column, and A s t A_{st} A s t ​ is the total area of longitudinal steel.

To account for accidental eccentricities, the nominal axial strength is reduced to P n , m a x P_{n,max} P n , ma x ​ :

Tied columns : P n , m a x = 0.80 P 0 P_{n,max} = 0.80 P_0 P n , ma x ​ = 0.80 P 0 ​ (strength reduction factor ϕ = 0.65 \phi = 0.65 ϕ = 0.65 ; design strength ϕ P n , m a x = 0.52 P 0 \phi P_{n,max} = 0.52 P_0 ϕ P n , ma x ​ = 0.52 P 0 ​ )

Spiral columns : P n , m a x = 0.85 P 0 P_{n,max} = 0.85 P_0 P n , ma x ​ = 0.85 P 0 ​ (strength reduction factor ϕ = 0.75 \phi = 0.75 ϕ = 0.75 ; design strength ϕ P n , m a x = 0.6375 P 0 \phi P_{n,max} = 0.6375 P_0 ϕ P n , ma x ​ = 0.6375 P 0 ​ )

Column Reinforcement Limits and Tie Spacing

Longitudinal steel ratio ( ρ g = A s t / A g \rho_g = A_{st} / A_g ρ g ​ = A s t ​ / A g ​ ): Must be between 1% and 8%. In practice, ratios above 4% make steel placement very difficult due to congestion at splices.

Minimum number of longitudinal bars : 4 for rectangular ties, 6 for spiral columns.

Tie spacing ( s s s ): For tied columns, the spacing of lateral ties must not exceed the minimum of:

  • 16 longitudinal bar diameters ( 16 d b 16 d_b 16 d b ​ )
  • 48 tie bar diameters ( 48 d t i e 48 d_{tie} 48 d t i e ​ )

The least lateral dimension of the column cross-section.

Furthermore, lateral ties must be arranged such that every corner and alternate longitudinal bar is laterally supported by a tie corner with an interior angle of not more than 135 degrees, and no bar can be more than 6 inches clear on either side from such a laterally supported bar.

Loading diagram... Whitney Stress Block and Strain Profile

ACI 318 Strength Reduction Factors