Study guide
10.5 Support of Excavation (Trenching, Cofferdams)
NCEES PE Civil Construction Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Soil Mechanics
1.1 Lateral Earth Pressure 1.2 Soil Consolidation and Settlement 1.3 Effective and Total Stresses 1.4 Bearing Capacity 1.5 Slope Stability
2 Chapter 2: Site Layout and Development
2.1 Layout and Control 2.2 Horizontal and Vertical Curves 2.3 Site Investigations and Utilities
3 Chapter 3: Material Properties
3.1 Soils, Rock, and Aggregates 3.2 Concrete Material Properties 3.3 Steel Material Properties 3.4 Wood Material Properties
4 Chapter 4: Estimating Quantities and Costs
4.1 Quantity Take-Off Methods 4.2 Cost Estimating 4.3 Engineering Economics 4.4 Work Measurement and Productivity (Earned Value)
5 Chapter 5: Project Planning and Scheduling
5.1 Construction Sequencing 5.2 Activity Time Analysis 5.3 Critical Path Method and Network Analysis 5.4 Resource Scheduling and Leveling 5.5 Time–Cost Trade-Off and Crashing
6 Chapter 6: Material Production, Execution, and Quality Control
6.1 Specification Conformance and Hold-Points 6.2 Field Testing: Concrete, Soils, and Aggregates 6.3 Compaction: Principles, Calculations, and Equipment 6.4 Concrete Placement, Consolidation, and Finishing 6.5 Bolting and Welding: Structural Steel Connections 6.6 Acceptance Sampling and Statistical Quality Control
7 Chapter 7: Structural Mechanics
7.1 Loads (Dead, Live, Construction, Wind, and Preloading) 7.2 Statics and Stresses (Bending, Shear, Deflection) 7.3 Beams, Columns, and Slabs 7.4 Foundation and Retaining Wall Mechanics
8 Chapter 8: Hydraulics and Hydrology
8.1 Stormwater Collection and Drainage (Open-Channel Flow) 8.2 Runoff Analysis 8.3 Detention and Retention Ponds
9 Chapter 9: Operations and Methods
9.1 Lifting and Rigging 9.2 Crane Capacity and Stability 9.3 Dewatering and Pumping 9.4 Equipment Selection and Production Rates 9.5 Deep Foundation Installation 9.6 Excavation and Embankment (Cut and Fill)
10 Chapter 10: Support of Construction Loads
10.1 Formwork Design 10.2 Falsework and Scaffolding 10.3 Shoring and Reshoring 10.4 Bracing and Anchorage 10.5 Support of Excavation (Trenching, Cofferdams) 10.6 Erection and Equipment Loads on Permanent Structures
11 Chapter 11: Health and Safety
11.1 OSHA Construction Regulations and Safety Management 11.2 Work Zone and Public Safety (Traffic Control)
10.5 Support of Excavation (Trenching, Cofferdams)
Key Takeaways Explain This Topic AI
Excavations deeper than 5 feet require a protective system (sloping, shoring, or shielding) unless cut entirely in stable rock.
Soil classification (Type A, B, or C) dictates the allowable slope angles and the design of shoring systems.
Sheet piling and soldier pile walls provide active earth support, utilizing embedment depth and internal struts or tiebacks for stability.
Cofferdams must be designed to resist hydrostatic pressure, hydrodynamic forces, and groundwater seepage (piping).
Last updated: July 2026
Introduction to Support of Excavation
Excavation and trenching are among the most hazardous construction operations. A soil cave-in occurs when the shear stress in the soil wedge exceeds the soil's shear strength, causing the walls of the excavation to collapse. Under OSHA 1926 Subpart P , excavations deeper than 5 feet 5\text{ feet} 5 feet require a protective system (sloping, shoring, or shielding) unless cut entirely in stable rock. For excavations deeper than 20 feet 20\text{ feet} 20 feet , the protective system must be designed by a registered professional engineer. In addition, a safe means of egress (ladders, steps, or ramps) is required for trenches 4 feet 4\text{ feet} 4 feet or deeper, with a maximum lateral travel distance of 25 feet 25\text{ feet} 25 feet for workers.
Soil Classification and Sloping Systems
Under OSHA regulations, soil is classified into three types based on unconfined compressive strength ( q u q_u q u ):
Type A: Cohesive soils (clays, silty clays) with q u > 1.5 tsf q_u > 1.5\text{ tsf} q u > 1.5 tsf (tons per square foot). No soil can be classified as Type A if it is fissured, subject to vibration, or has water seeping.
Type B: Cohesive soils with 0.5 < q u ≤ 1.5 tsf 0.5 < q_u \le 1.5\text{ tsf} 0.5 < q u ≤ 1.5 tsf , or granular cohesionless soils (silt, sandy loam), or previously disturbed soils.
Type C: Cohesive soils with q u ≤ 0.5 tsf q_u \le 0.5\text{ tsf} q u ≤ 0.5 tsf , granular soils (sand, gravel), submerged soils, or soils with active water seepage.
The maximum allowable slope (Horizontal to Vertical, H:V) for sloping systems is dictated by these soil types:
- Type A: 0.75 : 1 0.75:1 0.75 : 1 ( 53 ∘ 53^\circ 5 3 ∘ )
- Type B: 1 : 1 1:1 1 : 1 ( 45 ∘ 45^\circ 4 5 ∘ )
- Type C: 1.5 : 1 1.5:1 1.5 : 1 ( 34 ∘ 34^\circ 3 4 ∘ )
Benching (excavating steps) is permitted only in cohesive soils (Type A and B) and is strictly prohibited in granular Type C soils.
Earth Retention Systems
In urban areas or deep excavations where sloping is impossible due to property limits, structural support systems are required. These include sheet pile walls, soldier piles with lagging, and cofferdams.
Sheet Pile and Soldier Pile Walls
Sheet piles are interlocking steel sections driven into the subgrade. Cantilever sheet piles rely on embedment depth for stability and are limited to shallow cuts. Anchored sheet piles use ground anchors (tiebacks) or internal struts to resist lateral loads. Soldier pile walls use vertical steel H-piles driven at intervals, with horizontal timber lagging inserted between them as excavation proceeds.
Unlike permanent retaining walls designed using Rankine active pressure, braced excavations with struts do not rotate about their base. Therefore, they do not mobilize a linear triangular active pressure distribution. Instead, engineers use Peck's Apparent Earth Pressure Diagrams to design struts, walers, and lagging. For sand, the maximum apparent lateral pressure is constant at 0.65 K a γ H 0.65 K_a \gamma H 0.65 K a γ H . For clays, the pressure envelope is trapezoidal, varying based on the stability number N b = γ H / c N_b = \gamma H / c N b = γ H / c , where γ \gamma γ is unit weight, H H H is depth, and c c c is cohesion.
Cofferdams and Groundwater Seepage
A cofferdam is a temporary watertight enclosure driven into water-bearing ground or open water and dewatered to allow construction in a dry environment. A major failure mode for cofferdams is piping (also known as a boiling or quicksand condition). Dewatering the inside of the cofferdam creates a hydraulic head difference, forcing water to flow under the sheet piles and seep upward through the excavation floor. This upward flow exerts a drag force on the soil particles.
If the upward seepage pressure equals the buoyant unit weight of the soil, the effective stress drops to zero ( σ ′ = 0 \sigma' = 0 σ ′ = 0 ). The soil loses all shear strength, behaving like a liquid. The critical hydraulic gradient ( i c i_c i c ) at which this occurs is: ∋ c = γ ′ γ w = G s − 1 1 + e \ni_c = \frac{\gamma'}{\gamma_w} = \frac{G_s - 1}{1 + e} ∋ c = γ w γ ′ = 1 + e G s − 1
where:
γ ′ \gamma' γ ′ is the buoyant unit weight of soil ( pcf \text{pcf} pcf ).
γ w \gamma_w γ w is the unit weight of water ( 62.4 pcf 62.4\text{ pcf} 62.4 pcf ).
G s G_s G s is the specific gravity of soil solids (typically 2.65 to 2.70 2.65\text{ to }2.70 2.65 to 2.70 ).
e e e is the void ratio of the soil.
The actual hydraulic gradient is i = Δ h / L i = \Delta h / L i = Δ h / L , where Δ h \Delta h Δ h is the head difference and L L L is the length of the flow path. The Factor of Safety ( FS \text{FS} FS ) against piping is: FS = i c i \text{FS} = \frac{i_c}{i} FS = i i c
A minimum Factor of Safety of 1.5 to 2.0 1.5\text{ to }2.0 1.5 to 2.0 is required.
Worked Engineering Example: Piping Safety Check
Problem Scenario: A cofferdam is excavated in a fine sand deposit. The sheet piles are driven to an embedment depth that provides a groundwater flow path length of L = 15 feet L = 15\text{ feet} L = 15 feet beneath the bottom of the excavation. The groundwater table outside the cofferdam is 9 feet 9\text{ feet} 9 feet above the excavation floor, which is pumped dry ( Δ h = 9 feet \Delta h = 9\text{ feet} Δ h = 9 feet ). Laboratory testing indicates the sand has a specific gravity of G s = 2.68 G_s = 2.68 G s = 2.68 and an in-place void ratio of e = 0.60 e = 0.60 e = 0.60 . Calculate the critical hydraulic gradient ( i c i_c i c ), the actual hydraulic gradient ( i i i ), and determine the Factor of Safety against piping.
Step 1: Calculate the critical hydraulic gradient ( i c i_c i c ). ∋ c = G s − 1 1 + e = 2.68 − 1 1 + 0.60 = 1.05 \ni_c = \frac{G_s - 1}{1 + e} = \frac{2.68 - 1}{1 + 0.60} = 1.05 ∋ c = 1 + e G s − 1 = 1 + 0.60 2.68 − 1 = 1.05
Step 2: Calculate the actual hydraulic gradient ( i i i ). ∋ = Δ h L = 9 ft 15 ft = 0.60 \ni = \frac{\Delta h}{L} = \frac{9\text{ ft}}{15\text{ ft}} = 0.60 ∋= L Δ h = 15 ft 9 ft = 0.60
Step 3: Calculate the Factor of Safety against piping. FS = i c i = 1.05 0.60 = 1.75 \text{FS} = \frac{i_c}{i} = \frac{1.05}{0.60} = 1.75 FS = i i c = 0.60 1.05 = 1.75
Conclusion: The Factor of Safety is 1.75 1.75 1.75 . Since 1.75 ≥ 1.50 1.75 \ge 1.50 1.75 ≥ 1.50 , the excavation is safe against piping under these conditions.
Critical Field Traps in Excavation Support
Incorrect Soil Classification: Classifying a soil as Type A based solely on visual inspection when it is actually a fissured clay or near heavy traffic vibrations. These factors automatically downgrade the soil to Type B or C.
Spoils Pile Placement: OSHA requires that the excavated soil (spoils pile) and any construction equipment be placed at least 2 feet 2\text{ feet} 2 feet away from the edge of the excavation. Placing loads too close creates a surcharge that increases lateral earth pressure and triggers shallow slope failure.
Water Accumulation: Water seeping into a trench must be actively pumped out. Water accumulation increases lateral pressure (hydrostatic force) and reduces the soil's effective stress and cohesion, accelerating cave-ins.
Misusing Trench Boxes: A trench box does not prevent trench wall movement. If a large void exists between the trench box and the soil wall, a cave-in can impact the box dynamically, crushing it or knocking it over. Backfilling the space between the box and the soil wall is critical.