Study guide
10.2 Falsework and Scaffolding
NCEES PE Civil Construction Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Soil Mechanics
1.1 Lateral Earth Pressure 1.2 Soil Consolidation and Settlement 1.3 Effective and Total Stresses 1.4 Bearing Capacity 1.5 Slope Stability
2 Chapter 2: Site Layout and Development
2.1 Layout and Control 2.2 Horizontal and Vertical Curves 2.3 Site Investigations and Utilities
3 Chapter 3: Material Properties
3.1 Soils, Rock, and Aggregates 3.2 Concrete Material Properties 3.3 Steel Material Properties 3.4 Wood Material Properties
4 Chapter 4: Estimating Quantities and Costs
4.1 Quantity Take-Off Methods 4.2 Cost Estimating 4.3 Engineering Economics 4.4 Work Measurement and Productivity (Earned Value)
5 Chapter 5: Project Planning and Scheduling
5.1 Construction Sequencing 5.2 Activity Time Analysis 5.3 Critical Path Method and Network Analysis 5.4 Resource Scheduling and Leveling 5.5 Time–Cost Trade-Off and Crashing
6 Chapter 6: Material Production, Execution, and Quality Control
6.1 Specification Conformance and Hold-Points 6.2 Field Testing: Concrete, Soils, and Aggregates 6.3 Compaction: Principles, Calculations, and Equipment 6.4 Concrete Placement, Consolidation, and Finishing 6.5 Bolting and Welding: Structural Steel Connections 6.6 Acceptance Sampling and Statistical Quality Control
7 Chapter 7: Structural Mechanics
7.1 Loads (Dead, Live, Construction, Wind, and Preloading) 7.2 Statics and Stresses (Bending, Shear, Deflection) 7.3 Beams, Columns, and Slabs 7.4 Foundation and Retaining Wall Mechanics
8 Chapter 8: Hydraulics and Hydrology
8.1 Stormwater Collection and Drainage (Open-Channel Flow) 8.2 Runoff Analysis 8.3 Detention and Retention Ponds
9 Chapter 9: Operations and Methods
9.1 Lifting and Rigging 9.2 Crane Capacity and Stability 9.3 Dewatering and Pumping 9.4 Equipment Selection and Production Rates 9.5 Deep Foundation Installation 9.6 Excavation and Embankment (Cut and Fill)
10 Chapter 10: Support of Construction Loads
10.1 Formwork Design 10.2 Falsework and Scaffolding 10.3 Shoring and Reshoring 10.4 Bracing and Anchorage 10.5 Support of Excavation (Trenching, Cofferdams) 10.6 Erection and Equipment Loads on Permanent Structures
11 Chapter 11: Health and Safety
11.1 OSHA Construction Regulations and Safety Management 11.2 Work Zone and Public Safety (Traffic Control)
10.2 Falsework and Scaffolding
Key Takeaways Explain This Topic AI
Falsework refers to temporary structures that support permanent structures (like concrete slabs or bridge decks) until they become self-supporting.
Scaffolding is a temporary structure used to support workers and materials during the construction, repair, or cleaning of a structure.
Falsework design must rigorously evaluate load paths, member capacities, and overall stability, particularly buckling of vertical posts.
OSHA categorizes scaffolds by load ratings (Light, Medium, Heavy) and strictly enforces fall protection and structural safety standards.
Last updated: July 2026
Introduction to Falsework and Scaffolding
In construction, temporary structures support the project before it is self-supporting. While formwork molds the concrete, falsework is the temporary structural system designed to support the dead load of forms, reinforcing steel, fresh concrete, and construction live loads. By contrast, scaffolding is an independent, temporary platform system engineered to provide safe access for workers, tools, and materials. Because falsework and scaffolding carry significant loads, engineering failures are often catastrophic. Consequently, they are heavily regulated by codes such as ASCE 37 (Design Loads on Structures During Construction), ACI 347 (Guide to Formwork for Concrete), and OSHA 1926 Subpart L (Scaffolds).
- Structural Design of Falsework Systems
- Load Paths and Structural Mechanics
Designing falsework requires tracing loads through an uninterrupted path to a solid foundation: Slab/Deck → Plywood Sheathing → Joists → Stringers → Vertical Shores → Mudsills → Subgrade/Soil \text{Slab/Deck} \rightarrow \text{Plywood Sheathing} \rightarrow \text{Joists} \rightarrow \text{Stringers} \rightarrow \text{Vertical Shores} \rightarrow \text{Mudsills} \rightarrow \text{Subgrade/Soil} Slab/Deck → Plywood Sheathing → Joists → Stringers → Vertical Shores → Mudsills → Subgrade/Soil
According to ASCE 37 , the design vertical load ( W W W ) is W = D + L W = D + L W = D + L , where D D D represents the dead load, including concrete ( 150 pcf 150\text{ pcf} 150 pcf ), reinforcing steel, and formwork self-weight ( 5 to 15 psf 5\text{ to }15\text{ psf} 5 to 15 psf ). L L L is the construction live load, which is a minimum of 20 psf 20\text{ psf} 20 psf for light-duty operations (hand placement) and 50 psf 50\text{ psf} 50 psf for heavy-duty operations (motorized carts). Concrete discharge via pump or bucket requires additional impact allowances.
In addition, falsework must resist lateral forces. ACI 347 dictates bracing to resist a minimum horizontal load equal to 2 % 2\% 2% of the total dead load or 100 lb/ft 100\text{ lb/ft} 100 lb/ft applied at the edge of the deck, whichever is greater. Diagonal cross-bracing is the primary method used to prevent racking.
Compression Member Stability and Buckling
Vertical shores are critical compression members. Their capacity is governed by elastic or inelastic buckling . The critical buckling capacity ( P c r P_{cr} P cr ) of a long compression member is defined by the Euler Buckling formula: P c r = π 2 E I ( K L ) 2 P_{cr} = \frac{\pi^2 E I}{(K L)^2} P cr = ( K L ) 2 π 2 E I
where E E E is the Modulus of Elasticity ( psi \text{psi} psi ), I I I is the minimum Moment of Inertia ( in 4 \text{in}^4 in 4 ), L L L is the unbraced length ( in \text{in} in ), and K K K is the effective length factor.
The factor K K K depends on end connections: pinned-pinned (typical wood shores with base plates): K = 1.0 K = 1.0 K = 1.0 ; fixed-pinned: K = 0.7 K = 0.7 K = 0.7 ; and fixed-free: K = 2.0 K = 2.0 K = 2.0 .
To maximize capacity, horizontal lacing is used to reduce the unbraced length ( L L L ). If a 16 -ft 16\text{-ft} 16 -ft shore is braced at its midpoint in both directions, L L L is cut to 8 -ft 8\text{-ft} 8 -ft , increasing its buckling load by a factor of four.
Worked Engineering Example: Shore Stability
Problem Scenario: A contractor is pouring a 9 -inch 9\text{-inch} 9 -inch thick reinforced concrete slab ( γ = 150 pcf \gamma = 150\text{ pcf} γ = 150 pcf ). The formwork dead weight is 8 psf 8\text{ psf} 8 psf , and the design live load is 50 psf 50\text{ psf} 50 psf . The slab is supported by nominal 4 × 4 4\times4 4 × 4 timber shores (actual dimensions 3.5 in × 3.5 in 3.5\text{ in} \times 3.5\text{ in} 3.5 in × 3.5 in ) arranged in a 4.0 -ft 4.0\text{-ft} 4.0 -ft square grid. The shores are unbraced over their entire 12 -ft 12\text{-ft} 12 -ft height, with pinned-pinned ends ( K = 1.0 K = 1.0 K = 1.0 ). Modulus of Elasticity E = 1.6 × 10 6 psi E = 1.6 \times 10^6\text{ psi} E = 1.6 × 1 0 6 psi . Using a Factor of Safety of 3.0 against Euler buckling, determine if the shores are structurally adequate.
Step 1: Calculate design load.
Concrete Dead Load: DL s l a b = 9 12 × 150 = 112.5 psf \text{DL}_{slab} = \frac{9}{12} \times 150 = 112.5\text{ psf} DL s l ab = 12 9 × 150 = 112.5 psf
- Formwork Dead Load: DL f o r m s = 8 psf \text{DL}_{forms} = 8\text{ psf} DL f or m s = 8 psf
- Live Load: LL = 50 psf \text{LL} = 50\text{ psf} LL = 50 psf
Total Load: w = 112.5 + 8 + 50 = 170.5 psf w = 112.5 + 8 + 50 = 170.5\text{ psf} w = 112.5 + 8 + 50 = 170.5 psf
Step 2: Calculate axial load on a shore.
Tributary Area: A t r i b = 4 × 4 = 16 sq ft A_{trib} = 4 \times 4 = 16\text{ sq ft} A t r ib = 4 × 4 = 16 sq ft
Axial Load ( P P P ): P = 170.5 × 16 = 2 , 728 lbs P = 170.5 \times 16 = 2,728\text{ lbs} P = 170.5 × 16 = 2 , 728 lbs
Step 3: Calculate Moment of Inertia ( I I I ).
I = b d 3 12 = 3.5 × ( 3.5 ) 3 12 ≈ 12.51 in 4 I = \frac{b d^3}{12} = \frac{3.5 \times (3.5)^3}{12} \approx 12.51\text{ in}^4 I = 12 b d 3 = 12 3.5 × ( 3.5 ) 3 ≈ 12.51 in 4
Step 4: Calculate Euler buckling load ( P c r P_{cr} P cr ).
Unbraced Length ( L L L ): L = 12 × 12 = 144 inches L = 12 \times 12 = 144\text{ inches} L = 12 × 12 = 144 inches
Critical Buckling Load: P c r = π 2 × ( 1.6 × 10 6 ) × 12.51 144 2 ≈ 9 , 524 lbs P_{cr} = \frac{\pi^2 \times (1.6 \times 10^6) \times 12.51}{144^2} \approx 9,524\text{ lbs} P cr = 14 4 2 π 2 × ( 1.6 × 1 0 6 ) × 12.51 ≈ 9 , 524 lbs
Step 5: Determine allowable buckling load.
P a l l o w = P c r FS = 9 , 524 3.0 ≈ 3 , 175 lbs P_{allow} = \frac{P_{cr}}{\text{FS}} = \frac{9,524}{3.0} \approx 3,175\text{ lbs} P a ll o w = FS P cr = 3.0 9 , 524 ≈ 3 , 175 lbs
Conclusion: The shore is adequate since the design load ( 2 , 728 lbs 2,728\text{ lbs} 2 , 728 lbs ) is less than the allowable buckling load ( 3 , 175 lbs 3,175\text{ lbs} 3 , 175 lbs ).
- Scaffolding Systems and Safety Regulations (OSHA 1926 Subpart L)
- Scaffold Load Ratings and Safety Factors
Under OSHA 1926.451 , scaffolds are classified by uniform capacity: Light Duty ( 25 psf 25\text{ psf} 25 psf for workers and hand tools), Medium Duty ( 50 psf 50\text{ psf} 50 psf for bricklaying or concrete finishing), and Heavy Duty ( 75 psf 75\text{ psf} 75 psf for stone masonry or stockpiled materials). Scaffold components must support their self-weight and at least four times the maximum intended load, representing a 4 : 1 4:1 4 : 1 safety factor, while suspension cables require a 6 : 1 6:1 6 : 1 safety factor.
Mandatory Erection and Safety Protocols
OSHA guidelines mitigate hazards: platforms must be fully planked with scaffold-grade lumber, with gaps under 1 inch 1\text{ inch} 1 inch . Planks must extend past end supports by 6 to 12 inches 6\text{ to }12\text{ inches} 6 to 12 inches unless cleated. Fall protection is mandatory at heights of 10 feet 10\text{ feet} 10 feet or more; top rails must be 38 to 45 inches 38\text{ to }45\text{ inches} 38 to 45 inches high and support 200 lbs 200\text{ lbs} 200 lbs of force. Scaffold legs must rest on adjustable base plates and mudsills, never on loose bricks or barrels. Finally, supported scaffolds with a height-to-base-width ratio exceeding 4 : 1 4:1 4 : 1 must be secured to the structure with ties or guys.
Critical Field Traps in Falsework and Scaffolding
Common field traps include placing mudsills on uncompacted or frozen ground, which thaws or saturates, causing differential settlement and progressive collapse. Another trap is exceeding the slenderness ratio limit of L / d ≤ 50 L/d \le 50 L / d ≤ 50 for timber shores, often by piecing timbers together with scab joints that act as hinges. Finally, omitting diagonal bracing leaves the temporary structure with no shear rigidity, allowing it to rack and collapse parallelogram-style under wind or concrete discharge surge loads.