Study guide
2.2 Flow, Counter, and Motion Sensors
NCEES PE Control Systems Engineering Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Handbook, ISA-5.1, and IEC 61511 on Exam Day 1.3 CBT Strategy, AITs, Calculators, and Pacing
2 Process Measurement Sensors
2.1 Pressure, Level, and Temperature Sensors 2.2 Flow, Counter, and Motion Sensors 2.3 Analytical Instruments and Sampling Systems
3 Specialty Sensors and Characteristics
3.1 Fire and Gas Detectors 3.2 Machinery Monitoring and Protection 3.3 Sensor Characteristics: Accuracy, Calibration, and Dynamics
4 Selection, Installation, and Primary Calculations
4.1 Sensor Selection and Material Compatibility 4.2 Sensor Installation Details and Drawings 4.3 Flow Calculations 4.4 Level Calculations
5 Conversions, Thermowells, and Checkout
5.1 Process Measurement Unit Conversions 5.2 Thermowell Design and Wake Frequency 5.3 Sensor Testing and Commissioning
6 Drawings, Dynamics, and PID
6.1 P&IDs, Loop Diagrams, and ISA-5.1 Symbology 6.2 Process Dynamics and Loop Response 6.3 Feedback Control and PID
7 Advanced, Discrete, and Process Applications
7.1 Feedforward, Cascade, Ratio, Override, and Split-Range 7.2 Discrete and Sequential Control 7.3 Control of Common Process Equipment
8 HMI, Alarms, Logic, and Architecture
8.1 HMI, Displays, and Control-Room Layout 8.2 Alarm Management 8.3 IEC 61131-3 Logic Implementation 8.4 DCS, PLC, SCADA Architecture and Interfaces
9 Capacity, Testing, and Cybersecurity
9.1 Capacity, Availability, Heat Load, Power, and Environment 9.2 FAT, IST, SAT, and Commissioning 9.3 Performance Monitoring and Management of Change 9.4 Control-System Cybersecurity
10 Valve Type, Trim, Sizing, and Actuators
10.1 Valve Types and Materials 10.2 Valve Trim, Leakage Class, and Characteristics 10.3 Valve Sizing, Pressure Drop, and Split-Range 10.4 Actuators and Failure Modes
11 Fluid Dynamics, Accessories, and Relief Types
11.1 Cavitation, Flashing, Choked Flow, and Noise 11.2 Valve Accessories and Installation 11.3 Pressure-Relieving Device Types and Installation 11.4 Pressure-Relieving Device Calculations
12 Motors, Solenoids, Regulators, and Checkout
12.1 Motor Starters, VSDs, and Soft Starters 12.2 Solenoid Valves and Relays as Final Elements 12.3 Self-Regulating Devices 12.4 Final Element Testing and Commissioning
13 Signal Types and Conversion
13.1 Analog and Discrete Signal Types 13.2 Buses, Topologies, and Digital Protocols 13.3 Signal Conversion, I/P, Splitters, and Bit Precision
14 Hazardous Areas, Power, and Circuits
14.1 Hazardous-Area Methods and Intrinsic Safety 14.2 Power, Grounding, Segregation, and EMI 14.3 Two-Wire, Four-Wire, and Loop Calculations
15 Media and Network Architecture
15.1 Transmission Media: Copper, Fiber, Wireless 15.2 TCP/IP, OPC, Addressing, and Architectures 15.3 OPC, Network Addressing, and Segmentation
16 Lifecycle and Risk Allocation
16.1 IEC 61511 Lifecycle Structure and Phases 16.2 Hazard and Risk Assessment 16.3 LOPA, IPLs, and SIF Identification
17 SRS, Design, and SIL Calculations
17.1 Safety Requirements Specification 17.2 SIS Design, Device Selection, and Constraints 17.3 SIL Calculations and Formulas
18 SAT, Proof Testing, and MOC
18.1 Installation, Commissioning, Validation, and SAT 18.2 Operation, Proof Testing, Demands, and Bypasses 18.3 Modification, Decommissioning, and MOC
2.2 Flow, Counter, and Motion Sensors
Key Takeaways Explain This Topic AI
Orifice, venturi, nozzle, pitot, and averaging-pitot meters infer volumetric flow from DP and need density (and usually straight run) to report mass; Coriolis measures mass and density directly.
Conventional magnetic flowmeters need a full pipe of conductive liquid (typically ≥ about 5 μS/cm) and have no vortex-style high-Reynolds cutoff; vortex meters need high Re and drop out at low flow.
Transit-time ultrasonic meters need an acoustically clean path; Doppler meters need particles or bubbles as scatterers—do not swap them.
Coriolis is justified when 0.1%-class mass (and usually density) plus weak straight-run needs beat orifice-plus-densitometer uncertainty and installed cost, especially on high-value or custody streams.
Pulse counters and turbine pickups totalize K-factor pulses; proximity probes, encoders, tachometers, and LVDTs are the motion set for speed and stem position, not process flow.
Last updated: August 2026
Flowmeters the PE exam actually specifies
Flow questions on PE Control Systems are almost never 'what is Bernoulli's equation.' They are: which meter survives this phase, which one is linear at this Reynolds number, and whether you can afford Coriolis or must live with an orifice plus a density correction. Treat mass flow and volumetric flow as different PVs. An orifice infers volume (actually a discharge through an area) from DP; mass is inferred only after density. Coriolis reports mass from tube twist and density from tube frequency.
DP primary elements
Orifice plates (concentric, eccentric, segmental) are the lowest-capital DP primary. Permanent pressure loss is high (a large fraction of the measured DP does not recover). Uncalibrated discharge-coefficient uncertainty is often on the order of 0.5–2% of rate depending on β, tap type, and International Organization for Standardization (ISO) 5167 / ASME MFC-3M compliance. They need straight run (commonly 10–30 diameters upstream after a disturbance, plus downstream recovery). Square-root extraction is in the transmitter or distributed control system (DCS); at 10% of max flow you have 1% of max DP, so noise and zero error explode—this is why DP flow has poor rangeability unless you stack transmitters or use characterization carefully.
A venturi recovers most of the DP, so permanent loss is low; it handles dirty fluids better than a sharp-edged orifice and costs more to install. A flow nozzle sits between orifice and venturi: common on steam, intermediate recovery, still a DP device. A pitot tube is a point-velocity sensor; a traverse is required if the profile is unknown. An averaging pitot (multiple ports across the pipe) reduces ΔP versus an orifice on large ducts and still needs density for mass. All DP primaries need impulse-line discipline: condensate pots on steam, purges on dirty gas, and no gas trapped in liquid legs.
Magnetic, vortex, turbine, and variable area
A magnetic flowmeter uses Faraday's law (E = B·L·v) in a conductive liquid. Conventional magmeters want roughly ≥ 5 μS/cm (special designs go lower; hydrocarbons and gases are still out). There is essentially no permanent pressure drop, the pipe must be full, and liners (polytetrafluoroethylene (PTFE), rubber, ceramic) are a materials choice. Magmeters do not have a vortex-style high-Reynolds floor; they do have a velocity window (often about 0.3–12 m/s) and fail on empty pipe, gas breakout, and nonconductive fluids.
A vortex meter sheds von Kármán vortices; frequency f = St · v / d with Strouhal number near 0.2 in the linear range. Steam, gas, and many liquids work. Conductivity is irrelevant. The killer is Reynolds number : manufacturers typically want Re on the order of 10,000–20,000 or higher. Below the low-flow cutoff the meter is not 'a little less accurate'—it is off. High viscosity and oversized meters are how you fail a vortex application that looked fine at nameplate flow.
Turbine meters give a pulse train with a K-factor (pulses per gallon or per cubic meter). Accuracy on clean, lubricating liquids can be 0.15–0.5%, which is why they still appear in custody and fuel. Bearings and solids are the failure mode. The pulse train feeds a counter or totalizer—the same hardware idea as a turbine pickup on a pump or compressor shaft.
Variable-area meters (rotameters) are local, inexpensive, must be vertical, and are viscosity- and density-sensitive. Use them for purge indication, not as the custody PV.
Ultrasonic, Coriolis, thermal mass, positive displacement
Transit-time ultrasonic meters compare upstream and downstream flight times. They need an acoustically clean path: little solids, little bubbles, known pipe ID. Doppler ultrasonic meters need scatterers (particles or bubbles); they are the wrong meter on a clean, degassed liquid and the right one on many slurries. Neither requires electrical conductivity. Clamp-on uncertainty is worse than spool-piece uncertainty; do not claim 0.5% on a clamp-on without a calibration story.
Coriolis meters measure mass from oscillating-tube Coriolis force and density from natural frequency. Typical liquid mass accuracy is 0.1% class. Straight-run requirements are usually minimal. Pressure drop can be high on bent-tube designs; straight-tube designs drain and clean better. Gas Coriolis is possible but density (signal) is low—size carefully. Capital cost is several times an orifice run.
Thermal-mass meters infer gas mass from heated-velocity sensors. They are strong on clean gases and weak on changing composition, moisture, and liquids. Positive-displacement (PD) meters (oval gear, rotary) shine on viscous liquids and custody where moving parts are acceptable. They add pressure drop and maintenance.
Counters and motion sensors
A pulse counter totalizes K-factor or pickup pulses for inventory and flow. Debounce, pull-up, and NAMUR (process-industry sensor interface) versus transistor-transistor logic (TTL) levels belong on the loop sheet. Proximity probes (inductive for metals, often in American Petroleum Institute (API) 670 machinery protection); capacitive for some nonmetals) give gap or pass/fail presence. Encoders (incremental or absolute) give shaft angle and, by differentiation, speed. A tachometer or magnetic pickup on a toothed wheel is frequency proportional to speed. A linear variable differential transformer (LVDT) is an AC-excited transformer whose core position (valve stem, damper) sets the secondary voltages—no sliding contact, good for dirty stem position compared with a potentiometer.
Meter versus process (phase, conductivity, accuracy, ΔP)
- Meter Typical phase Conductivity need Accuracy class (installed, honest) Permanent ΔP
- Orifice + DP Liquid, gas, steam None ~1–2% uncalibrated volume High
- Venturi Liquid, gas, steam None ~0.7–1.5% Low
- Flow nozzle Steam, gas, liquid None ~1% class Medium
- Averaging pitot Gas, steam, liquid None ~1–2%+ (profile) Low
- Magmeter Conductive liquid, full pipe Typically ≥ ~5 μS/cm conventional ~0.2–0.5% Essentially none
- Vortex Liquid, gas, steam None ~0.7–1.5% above Re cutoff Medium
- Turbine Clean liquid None ~0.15–0.5% Medium
- Transit-time US Clean liquid or gas None ~0.5–1% spool None
- Doppler US Dirty liquid with scatterers None ~1–5% None
- Coriolis Liquid (gas if sized) None ~0.1% mass; density extra Medium–high
- Thermal mass Gas None ~1–2%, composition-sensitive Low
- PD Viscous liquid None ~0.1–0.5% Medium
- Variable area Liquid or gas None ~2–10% local Medium
Relative hardware cost index for a typical 2 in liquid flow point (orifice run = 1)
Loading diagram... Mass-flow selection: orifice plus densitometer versus Coriolis
Worked example: when Coriolis beats orifice plus densitometer
A 2-inch finished acetic-acid line, 12,000 lb/h, 80 °C, liquid, Re ≈ 80,000, customer custody target ±0.2% mass , fluid worth about $1.20/lb. An orifice (β ≈ 0.6) plus DP infers volumetric-like flow; mass needs density. Density of acetic acid moves several percent from 20 °C to 80 °C. A separate densitometer (vibrating element or nuclear) adds capital, another failure mode, and stacked uncertainty. Combined mass uncertainty of 0.5–1% is common if the orifice is not proving-quality and the density loop is ordinary.
A 0.5% mass error is 60 lb/h. Annualized: 60 × 8760 × $1.20 ≈ $630,000/year of measurement money, even before contract penalties. A liquid Coriolis at 0.1% mass, with density from the same tubes, typically costs on the order of $12,000–$25,000 installed versus $3,000–$6,000 for an orifice run. The Coriolis is justified. The same plant's cooling-water header at ±2% for energy balance is not a Coriolis project—use an orifice or magmeter (conductivity of treated water is usually ample).
Reynolds versus conductivity, mag versus vortex. A 2-inch full-pipe water line, 50 μS/cm, flow that swings from Re ≈ 8,000 to 80,000: the magmeter is in conductivity range and does not shut off at Re = 8,000. A vortex meter may be below its linear Re cutoff at the low end even though the high end looks perfect. Do not pick vortex 'because steam plants use vortex' when this service is low-Re liquid. Do not pick a magmeter for dry steam or hydrocarbon condensate with no conductivity.
Motion and exam traps
Specify an LVDT or a qualified positioner feedback for stem position; a cheap pot on a sticky stem is a loop-sheet lie. Do not use a Doppler meter on clean condensate. Do not claim orifice ±0.1% without a proving story. Square-root DP at 10% flow is a noise trap. Thermal mass on a composition-changing vent is a composition trap, not a flow trap.