Study guide

14.2 Power, Grounding, Segregation, and EMI

NCEES PE Control Systems Engineering Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Handbook, ISA-5.1, and IEC 61511 on Exam Day 1.3 CBT Strategy, AITs, Calculators, and Pacing

2 Process Measurement Sensors

2.1 Pressure, Level, and Temperature Sensors 2.2 Flow, Counter, and Motion Sensors 2.3 Analytical Instruments and Sampling Systems

3 Specialty Sensors and Characteristics

3.1 Fire and Gas Detectors 3.2 Machinery Monitoring and Protection 3.3 Sensor Characteristics: Accuracy, Calibration, and Dynamics

4 Selection, Installation, and Primary Calculations

4.1 Sensor Selection and Material Compatibility 4.2 Sensor Installation Details and Drawings 4.3 Flow Calculations 4.4 Level Calculations

5 Conversions, Thermowells, and Checkout

5.1 Process Measurement Unit Conversions 5.2 Thermowell Design and Wake Frequency 5.3 Sensor Testing and Commissioning

6 Drawings, Dynamics, and PID

6.1 P&IDs, Loop Diagrams, and ISA-5.1 Symbology 6.2 Process Dynamics and Loop Response 6.3 Feedback Control and PID

7 Advanced, Discrete, and Process Applications

7.1 Feedforward, Cascade, Ratio, Override, and Split-Range 7.2 Discrete and Sequential Control 7.3 Control of Common Process Equipment

8 HMI, Alarms, Logic, and Architecture

8.1 HMI, Displays, and Control-Room Layout 8.2 Alarm Management 8.3 IEC 61131-3 Logic Implementation 8.4 DCS, PLC, SCADA Architecture and Interfaces

9 Capacity, Testing, and Cybersecurity

9.1 Capacity, Availability, Heat Load, Power, and Environment 9.2 FAT, IST, SAT, and Commissioning 9.3 Performance Monitoring and Management of Change 9.4 Control-System Cybersecurity

10 Valve Type, Trim, Sizing, and Actuators

10.1 Valve Types and Materials 10.2 Valve Trim, Leakage Class, and Characteristics 10.3 Valve Sizing, Pressure Drop, and Split-Range 10.4 Actuators and Failure Modes

11 Fluid Dynamics, Accessories, and Relief Types

11.1 Cavitation, Flashing, Choked Flow, and Noise 11.2 Valve Accessories and Installation 11.3 Pressure-Relieving Device Types and Installation 11.4 Pressure-Relieving Device Calculations

12 Motors, Solenoids, Regulators, and Checkout

12.1 Motor Starters, VSDs, and Soft Starters 12.2 Solenoid Valves and Relays as Final Elements 12.3 Self-Regulating Devices 12.4 Final Element Testing and Commissioning

13 Signal Types and Conversion

13.1 Analog and Discrete Signal Types 13.2 Buses, Topologies, and Digital Protocols 13.3 Signal Conversion, I/P, Splitters, and Bit Precision

14 Hazardous Areas, Power, and Circuits

14.1 Hazardous-Area Methods and Intrinsic Safety 14.2 Power, Grounding, Segregation, and EMI 14.3 Two-Wire, Four-Wire, and Loop Calculations

15 Media and Network Architecture

15.1 Transmission Media: Copper, Fiber, Wireless 15.2 TCP/IP, OPC, Addressing, and Architectures 15.3 OPC, Network Addressing, and Segmentation

16 Lifecycle and Risk Allocation

16.1 IEC 61511 Lifecycle Structure and Phases 16.2 Hazard and Risk Assessment 16.3 LOPA, IPLs, and SIF Identification

17 SRS, Design, and SIL Calculations

17.1 Safety Requirements Specification 17.2 SIS Design, Device Selection, and Constraints 17.3 SIL Calculations and Formulas

18 SAT, Proof Testing, and MOC

18.1 Installation, Commissioning, Validation, and SAT 18.2 Operation, Proof Testing, Demands, and Bypasses 18.3 Modification, Decommissioning, and MOC

14.2 Power, Grounding, Segregation, and EMI

Key Takeaways Explain This Topic AI

Redundant 24 VDC bulk supplies are commonly diode-auctioneered onto one bus. Subtract the diode forward drop (about 0.3 V Schottky to 0.7 V silicon) from every solenoid and analog-loop voltage budget, and fuse so a field short cannot collapse the whole bus.

Round-trip voltage drop is Vd = I × 2 × R' × L. A 350 mA solenoid on 600 ft (one way) of 18 AWG at 6.5 Ω/1000 ft drops 2.73 V and sees 21.27 V from a 24.0 V bus — below a 21.6 V (−10%) coil floor.

Conventional analog 4–20 mA shields are usually grounded at one end, typically the I/O or marshalling end, to avoid a 60 Hz ground loop. VFD and motor-lead shields are bonded at both ends with 360° glands because the noise is high-frequency.

Keep analog and IS pairs out of VSD/motor-lead trays by distance or a metallic barrier. Ferrites and analog filters are cleanup after the geometry is fixed, not a substitute for segregation.

Single-point (star) grounding favors analog accuracy at power frequency. Multi-point bonding favors high-frequency EMC. Mixing the two without a plan is how plants create noisy 4–20 mA and circulating shield current.

Last updated: August 2026

A loop that is entity-correct and still chatters at 12 mA is not a classification problem. It is a power, grounding, and electromagnetic-compatibility problem. PE Control Systems items in this neighborhood ask whether the 24 V is still 24 V at the load, whether two supplies can share a bus without back-feeding, and whether the analog pair was routed as if it were another motor lead.

UPS, fusing, and diode-auctioneered 24 VDC

Control-room 120 VAC for DCS/PLC processors is usually an online (double-conversion) UPS : incoming AC is rectified and the inverter carries the load continuously, so transfer time is not a ride-through gamble. Line-interactive or standby UPS units that switch after a dropout are a poor match for switch-mode I/O supplies that already dropped out. SIS power is a separate battery-backed source when independence from the BPCS is part of the safety design; a shared UPS that dies for both systems is not “redundant” in the safety sense.

Field I/O more often lives on 24 VDC bulk with battery backup or a DC UPS. Size the battery for the documented ride-through (orderly shutdown versus continuous operation). Treat inrush of analog barriers, solenoids, and network switches as part of the current, not as a surprise after commissioning.

Fusing is coordination, not decoration. Fuse the +24 V feeder to a marshalled group so a shorted solenoid or a crushed tray takes that group, not the entire cabinet. The fuse in a zener barrier is part of the IS certificate — substituting a larger field-replaceable fuse is how a loop stops being the loop on the control drawing. Do not add a second series fuse on the IS field pair unless that fuse is on the drawing; extra resistance and extra opening energy were not in the entity file.

Diode auctioneering (diode-OR) lets two DC supplies feed one bus through steering diodes. The higher source voltage conducts; the lower sits reverse-biased. A silicon diode drops about 0.7 V ; a Schottky about 0.3–0.4 V . The bus the loops actually see is Vsupply − Vf , and that drop belongs in every analog and solenoid budget. Diodes must be rated for the full bus current plus inrush; a diode that opens is a single point of failure unless you have monitored parallel paths. If Supply A is 24.5 V and Supply B is 23.8 V, only A carries load until A fails — “both supplies sharing” is not what the circuit does.

Worked numeric voltage drop on a 24 V loop

Instrument copper at about 20 °C is close to 6.5 Ω per 1000 ft for 18 AWG and 4.1 Ω per 1000 ft for 16 AWG . Use those working values unless the problem states NEC Chapter 9 Table 8 (75 °C) resistances, which are higher.

Round-trip drop for a two-conductor run of one-way length L (in kft) and resistance R' (Ω/kft) is:

Vd = I × 2 × R' × L

Worked solenoid (power loop). A 24.0 VDC bulk bus feeds a coil that draws 350 mA holding. The one-way cable length is 600 ft of 18 AWG. Neglect the auctioneering diode for the first pass.

  • One-way resistance = 6.5 Ω/kft × 0.600 kft = 3.90 Ω
  • Round-trip resistance = 7.80 Ω
  • Vd = 0.350 A × 7.80 Ω = 2.73 V
  • Voltage at the coil = 24.00 − 2.73 = 21.27 V

A coil specified 24 V ±10% has a 21.6 V floor. 21.27 V is below 21.6 V , so the valve may chatter, pull in weakly, or drop out on a warm day when copper resistance rises. Two honest fixes: 16 AWG on the same route ( R_rt = 2 × 4.1 × 0.600 = 4.92 Ω , Vd = 1.72 V , Vcoil = 22.28 V ) or a shorter run / local 24 V supply. If you then auctioneer through a 0.4 V Schottky, subtract that from the bus first: 23.6 V at the cabinet already, then 2.73 V of cable, 20.87 V at the coil — the diode you ignored is now the whole problem.

Same cable, analog loop. At 20 mA , that 7.80 Ω round trip drops only 0.156 V . Analog cable drop is usually tenths of a volt. Solenoid and 4-wire transmitter power conductors are where 24 V loops actually fail voltage drop. Still include analog cable in the Section 14.3 compliance budget; it is small, not zero, and it grows with thin wire and long runs.

A 10% voltage-drop rule of thumb (2.4 V on a 24 V bus) is a screening test, not a substitute for the nameplate minimum. Many 24 V solenoids and 2-wire transmitters have a minimum operating voltage tighter than 10%.

Control-signal isolation is the other half of “the 24 V arrived but the milliamp signal is garbage.” When a field device, a cable shield, and a panel analog common sit on different earths, the difference current has nowhere to go except along the signal conductor. Analog isolators , isolated analog-input cards, and galvanic IS isolators break that metallic loop. Isolation is not optional just because both ends say “24 V common.”

Single-point versus multi-point grounding, and shields

Single-point (star) grounding ties analog commons, shield drains, and the cabinet earth bar to one reference so that 50/60 Hz current has no loop area to circulate. It is the default mental model for millivolt thermocouples and quiet 4–20 mA.

Multi-point bonding ties cable shields and armor to earth at more than one place so that high-frequency noise (VFD PWM edges, radio, ESD) has a short path off the shield. At a few hundred kilohertz, a 30 m drain wire to a distant star point is an inductor, not a ground.

Plants use both, on purpose:

Analog 4–20 mA and millivolt pairs: ground the shield at one end , almost always the control-room / I/O cabinet end. Leave the field end insulated unless the manufacturer’s control drawing says otherwise. Two-end analog shield grounds on a long pair are a 60 Hz loop around the tank farm earth gradient.

VFD / motor leads: bond the shield (or armor) at both ends with 360° glands , not a pigtail. The standing-wave and common-mode current on a PWM motor cable will not drain through a single pigtail.

Hybrid: some digital / fieldbus installations ground the shield at the cabinet and capacitor-couple the field end so that AC noise has a path while DC earth current does not. Follow the bus installation guide; do not invent a third earth on a spare drain.

The instrument cylinder ground and the electrical safety ground (PE) must still be bonded as a safety system. “Single-point analog” does not mean floating the cabinet. It means you do not let the analog shield be a parallel PE conductor between two buildings.

Segregation from VSD/motor leads, ferrites, and filters

A variable-speed drive’s motor leads are a fast common-mode noise source. Capacitive coupling into a parallel 4–20 mA pair looks like a wandering process value, a HART modem that will not connect, or a barrier that appears to “noise-trip.” Geometry beats firmware.

Do not pull analog, IS, or millivolt cable in the same conduit or undivided tray as VSD output or motor leads.

Separate with distance (a common installation practice is on the order of 300 mm ) or a grounded metallic barrier / separate steel tray.

Cross at right angles when the route must meet.

Use symmetric, shielded VFD cable, 360° termination, and a motor-end EMC gland. Unshielded THHN bundled with analog is the commissioning failure mode.

After the route is clean, ferrite sleeves (common-mode chokes) on the analog pair at the cabinet entry, and RC or active filters on the analog input, take residual RF. Ferrites on a still-bundled motor/analog pair treat the symptom.

Do not hang random capacitors across an IS pair to “filter noise.” That capacitance is Ci on the entity sheet.

Noise source What it couples into Mitigation that belongs on the drawing

VSD / motor leads (PWM edges) Analog 4–20 mA, HART, IS pairs Segregate trays; shielded symmetric motor cable; 360° glands; analog shield one-end

60 Hz earth gradient between buildings Shield loops, thermocouples Single-end analog shield ground; isolators; do not use shield as PE

Auctioneered 24 V bus ripple / shared returns Several loops at once Separate analog commons from solenoid returns; adequate bulk capacitance; star 24 V returns

Radio / handhelds / ESD at cabinets High-impedance millivolt inputs Ferrites at entry; filtered glands; keep spare analog pairs terminated

Lightning / switching surges on long pairs Transmitter electronics, AI cards IS-rated SPDs on the control drawing; bonding of barriers and glands

Contact bounce / solenoid kickback on the same 24 V Analog supply droop Separate fused 24 V for solenoids versus analog; freewheel diodes on coils

If the value jumped the day the VFD started, move the analog cable before you retune the PID.