Study guide
13.3 Signal Conversion, I/P, Splitters, and Bit Precision
NCEES PE Control Systems Engineering Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Handbook, ISA-5.1, and IEC 61511 on Exam Day 1.3 CBT Strategy, AITs, Calculators, and Pacing
2 Process Measurement Sensors
2.1 Pressure, Level, and Temperature Sensors 2.2 Flow, Counter, and Motion Sensors 2.3 Analytical Instruments and Sampling Systems
3 Specialty Sensors and Characteristics
3.1 Fire and Gas Detectors 3.2 Machinery Monitoring and Protection 3.3 Sensor Characteristics: Accuracy, Calibration, and Dynamics
4 Selection, Installation, and Primary Calculations
4.1 Sensor Selection and Material Compatibility 4.2 Sensor Installation Details and Drawings 4.3 Flow Calculations 4.4 Level Calculations
5 Conversions, Thermowells, and Checkout
5.1 Process Measurement Unit Conversions 5.2 Thermowell Design and Wake Frequency 5.3 Sensor Testing and Commissioning
6 Drawings, Dynamics, and PID
6.1 P&IDs, Loop Diagrams, and ISA-5.1 Symbology 6.2 Process Dynamics and Loop Response 6.3 Feedback Control and PID
7 Advanced, Discrete, and Process Applications
7.1 Feedforward, Cascade, Ratio, Override, and Split-Range 7.2 Discrete and Sequential Control 7.3 Control of Common Process Equipment
8 HMI, Alarms, Logic, and Architecture
8.1 HMI, Displays, and Control-Room Layout 8.2 Alarm Management 8.3 IEC 61131-3 Logic Implementation 8.4 DCS, PLC, SCADA Architecture and Interfaces
9 Capacity, Testing, and Cybersecurity
9.1 Capacity, Availability, Heat Load, Power, and Environment 9.2 FAT, IST, SAT, and Commissioning 9.3 Performance Monitoring and Management of Change 9.4 Control-System Cybersecurity
10 Valve Type, Trim, Sizing, and Actuators
10.1 Valve Types and Materials 10.2 Valve Trim, Leakage Class, and Characteristics 10.3 Valve Sizing, Pressure Drop, and Split-Range 10.4 Actuators and Failure Modes
11 Fluid Dynamics, Accessories, and Relief Types
11.1 Cavitation, Flashing, Choked Flow, and Noise 11.2 Valve Accessories and Installation 11.3 Pressure-Relieving Device Types and Installation 11.4 Pressure-Relieving Device Calculations
12 Motors, Solenoids, Regulators, and Checkout
12.1 Motor Starters, VSDs, and Soft Starters 12.2 Solenoid Valves and Relays as Final Elements 12.3 Self-Regulating Devices 12.4 Final Element Testing and Commissioning
13 Signal Types and Conversion
13.1 Analog and Discrete Signal Types 13.2 Buses, Topologies, and Digital Protocols 13.3 Signal Conversion, I/P, Splitters, and Bit Precision
14 Hazardous Areas, Power, and Circuits
14.1 Hazardous-Area Methods and Intrinsic Safety 14.2 Power, Grounding, Segregation, and EMI 14.3 Two-Wire, Four-Wire, and Loop Calculations
15 Media and Network Architecture
15.1 Transmission Media: Copper, Fiber, Wireless 15.2 TCP/IP, OPC, Addressing, and Architectures 15.3 OPC, Network Addressing, and Segmentation
16 Lifecycle and Risk Allocation
16.1 IEC 61511 Lifecycle Structure and Phases 16.2 Hazard and Risk Assessment 16.3 LOPA, IPLs, and SIF Identification
17 SRS, Design, and SIL Calculations
17.1 Safety Requirements Specification 17.2 SIS Design, Device Selection, and Constraints 17.3 SIL Calculations and Formulas
18 SAT, Proof Testing, and MOC
18.1 Installation, Commissioning, Validation, and SAT 18.2 Operation, Proof Testing, Demands, and Bypasses 18.3 Modification, Decommissioning, and MOC
13.3 Signal Conversion, I/P, Splitters, and Bit Precision
Key Takeaways Explain This Topic AI
Analog-to-digital and digital-to-analog converters map 4–20 mA (or 1–5 V) to integer codes; quantization is commonly bounded by ±½ LSB and isolation does not remove it.
An I/P converts 4–20 mA to 3–15 psi; a P/I reverses that; an I/I repeats or isolates current and may steal loop voltage if it is a passive series device.
Splitters duplicate a 4–20 mA signal for a second consumer; each series burden is a voltage tax that must be checked at 20 mA.
Engineering-unit resolution over a 4–20 mA span is approximately (URV − LRV)/2^n, so 16-bit is 16 times finer than 12-bit on the same span.
Stacking a series splitter and a series isolator on a 24 V loop is a classic brown-out: the transmitter can be left below its minimum terminal voltage at 20 mA.
Last updated: August 2026
Why conversion is its own spec item (4.B)
Specification 4.B is the hardware that sits between signal types: analog-to-digital (A/D) , digital-to-analog (D/A) , I/P , P/I , I/I , splitters, filters, and the bit precision of the converter. The exam loves two mistakes: treating bit depth as decoration instead of engineering-unit resolution, and stacking isolators and splitters until a 24 V loop cannot power the transmitter at 20 mA.
A/D, D/A, quantization, and isolation
An analog-input card samples a 4–20 mA (or 1–5 V) signal, usually after a burden resistor and an anti-aliasing filter, and maps it to an integer. That is A/D . An analog-output card does the reverse: integer to current — D/A . Quantization error is inherent: the true analog value is replaced by the nearest code. A common bound is ±½ LSB (least significant bit).
Galvanic isolation on the card or in a field isolator breaks ground loops and common-mode voltage. Isolation does not remove quantization, and a series isolator in the field adds voltage drop and its own transfer error. If two systems must share a 4–20 mA without tying commons, isolate on purpose — then pay for that isolation in the voltage budget, not as an afterthought.
If the converter’s electrical range is 0–20 mA or 0–24 mA but the process span is only 4–20 mA, some codes sit below live zero. Effective counts on the process span shrink: counts on span ≈ 2 n × 16 mA full-scale mA \text{counts on span} \approx 2^{n} \times \frac{16\text{ mA}}{\text{full-scale mA}} counts on span ≈ 2 n × full-scale mA 16 mA
Always ask whether n n n bits cover 4–20 mA or a wider card range. A “12-bit input” that actually digitizes 0–24 mA is coarser on the live-zero span than a 12-bit converter mapped only across 16 mA.
I/P, P/I, and I/I
An I/P (current-to-pneumatic) transducer converts 4–20 mA → 3–15 psi (sometimes 6–30 psi). That is how an electronic loop still drives a pneumatic actuator or positioner. Live zero maps to live zero: 4 mA → 3 psi, 12 mA → 9 psi, 20 mA → 15 psi. A P/I is the reverse, used when a pneumatic process variable must enter a distributed control system.
An I/I is a current isolator/repeater: 4–20 mA in, isolated 4–20 mA out. Use it to break a ground loop, to re-power a long run, or to feed a second system without tying commons. It is not free: a passive I/I sits in series and consumes loop voltage; an active (powered) I/I can source the output loop from a separate supply so the input loop only sees a modest burden.
Splitters and filters
A splitter takes one 4–20 mA and produces two (or more) isolated 4–20 mA outputs — for example the basic process control system and a local recorder, or a control analog input and a safety analog voter, with isolation between them. Passive splitters add series voltage drop on the input loop. Powered splitters need 24 V and still have input compliance limits.
Filters (RC, instrumentation-amplifier low-pass, 50/60 Hz rejection) sit before the A/D. They reduce aliasing and noise but add lag. Do not put a one-second filter on a loop that must trip in 200 ms, and do not skip anti-aliasing on a high-speed sampled input. Filtering is signal conditioning; it is not a substitute for shielding and a current loop.
Worked numeric: 12-bit versus 16-bit over a 4–20 mA span
A level transmitter is 4–20 mA = 0–80.00 in . The analog input maps that 16 mA span onto the converter (live zero aligned to 0% counts).
12-bit: 2 12 = 4096 2^{12} = 4096 2 12 = 4096 codes. Δ EU,12 = 80.00 in 4096 = 0.0195 in/bit \Delta_{\text{EU,12}} = \frac{80.00\text{ in}}{4096} = 0.0195\text{ in/bit} Δ EU,12 = 4096 80.00 in = 0.0195 in/bit
Half-LSB quantization ≈ ±0.0098 in .
16-bit: 2 16 = 65536 2^{16} = 65536 2 16 = 65536 codes. Δ EU,16 = 80.00 in 65536 = 0.00122 in/bit \Delta_{\text{EU,16}} = \frac{80.00\text{ in}}{65536} = 0.00122\text{ in/bit} Δ EU,16 = 65536 80.00 in = 0.00122 in/bit
Half-LSB ≈ ±0.00061 in .
The ratio is exact: 65536 / 4096 = 16 = 2 4 65536/4096 = 16 = 2^{4} 65536/4096 = 16 = 2 4 . Sixteen-bit is 16 times finer than 12-bit over the same span. If the process only needs 0.1 in resolution, both converters are finer than the requirement — and the analog transmitter accuracy, not the bit depth, will dominate. If the item asks which converter can resolve 0.002 in , only 16-bit gets there ( 0.00122 < 0.002 < 0.0195 0.00122 < 0.002 < 0.0195 0.00122 < 0.002 < 0.0195 ).
Using 2 n − 1 2^{n}-1 2 n − 1 instead of 2 n 2^{n} 2 n changes the 12-bit step from 0.0195 to 80 / 4095 ≈ 0.0195 80/4095 \approx 0.0195 80/4095 ≈ 0.0195 in — immaterial at PE precision. The traps are using 20 mA as the span instead of 16 mA , treating the card as 8-bit leftover from an old analog-output stereotype, or ignoring that a 0–24 mA card wastes codes below 4 mA.
Exam trap: splitter plus isolator kills the voltage budget
Loop voltage is checked at 20 mA (worst IR drop, worst burden).
Given: 24.0 VDC supply. Transmitter minimum 12.0 V at 20 mA. Cable loop resistance 100 Ω . Analog-input burden 250 Ω . A technician then series-inserts a passive isolator (5.0 V drop at 20 mA) and a passive splitter (another 5.0 V at 20 mA).
Drops at 20 mA:
- Cable: 0.020 × 100 = 2.0 0.020 \times 100 = 2.0 0.020 × 100 = 2.0 V
- Analog-input burden: 0.020 × 250 = 5.0 0.020 \times 250 = 5.0 0.020 × 250 = 5.0 V
- Isolator: 5.0 V
- Splitter: 5.0 V
- Sum of drops = 17.0 V
- Voltage left for the transmitter: 24.0 − 17.0 = 7.0 24.0 - 17.0 = 7.0 24.0 − 17.0 = 7.0 V
7.0 V < 12.0 V required. The transmitter browns out as current rises: the process variable may peg, drop toward a fail-low current, or chatter. The fix is not a bigger splitter. Use a powered splitter/isolator that does not steal 10 V from the input loop, raise the supply if the transmitter allows, shorten or thicken the cable, or take the second copy from a control-system analog output or HART instead of another series burden.
Without the two add-ons, remaining voltage would be 24.0 − 2.0 − 5.0 = 17.0 24.0 - 2.0 - 5.0 = 17.0 24.0 − 2.0 − 5.0 = 17.0 V — comfortably above 12 V. The stack, not the original loop, is what dies.
Caution
Stacking burdens
Every series device is a voltage tax at 20 mA. Isolator + splitter + barrier + 250 Ω card is how a healthy 24 V design fails on paper while each device “only drops 5 V.”
After you can scale milliamps, pick HART versus fieldbus, and defend a loop voltage budget, drill mixed Signals items at /practice/pe-control-systems .