Study guide
7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition)
PE Electrical and Computer: Power Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Strategy & Reference Handbook
1.1 PE Power Exam Format, CBT Navigation & Reference Handbook 1.2 2026 Reference Standards (NEC 2020, NFPA 70E-2021, NESC) & Scoring Mechanics 1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery
2 Chapter 2: Measurement, Metering & Field Testing
2.1 Current Transformers (CTs), Potential Transformers (PTs) & Meter Connections 2.2 Instrument Transformer Burdens, Saturation Curves & Ratio Correction Factors 2.3 Insulation Resistance Testing (Megger, Polarization Index, Dielectric Absorption) 2.4 Ground Resistance Testing (Fall-of-Potential 62% Rule & Clamp-on Methods)
3 Chapter 3: General Applications — Grounding & Surge Protection
3.1 Substation Ground Grid Design & IEEE 80 Touch/Step Voltage Criteria 3.2 Lightning Protection Systems & Rolling Sphere / Cone of Protection Methods 3.3 Surge Protective Devices (SPDs) & Voltage Surge Arresters
4 Chapter 4: General Applications — Lighting & Energy Management
4.1 Illumination Engineering & Zonal Cavity / Lumen Method Calculations 4.2 Energy Management, Demand Factors & Load Factor Calculations 4.3 Economic Dispatch, Energy Efficiency & Load Profile Analysis
5 Chapter 5: Electrical Safety & NFPA Standards
5.1 NFPA 70E Shock Protection, Approach Boundaries & PPE Requirements 5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations 5.3 Hazardous (Classified) Locations (Class I, II, III & Division/Zone Systems) 5.4 Special Occupancies & Critical Systems (NEC Articles 517 Health Care, 700/701/702 Emergency)
6 Chapter 6: NEC Wiring Methods & Installation Requirements
6.1 Conductor Ampacity & NEC Table 310.16 Derating Adjustments 6.2 Raceway Fill, Box Sizing & Conduit Bending Calculations (Chapter 9 Tables) 6.3 Equipment Grounding Conductors & Grounding Electrode Sizing (NEC Article 250)
7 Chapter 7: Circuit Analysis — Fundamentals & Symmetrical Components
7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition) 7.2 Balanced Three-Phase Circuits (Wye-Delta Configurations & Power Formulas) 7.3 Symmetrical Components & Fortescue Sequence Transformation Matrices 7.4 Sequence Impedances & Positive, Negative, Zero Sequence Network Construction
8 Chapter 8: Circuit Analysis — Per-Unit & Phasor Analysis
8.1 Per-Unit System Fundamentals & Base Conversion Formulas 8.2 Three-Phase Per-Unit Network Modeling & Equipment Impedance Conversion 8.3 Phasor Diagrams, Complex Power & Power Triangle Relationships
9 Chapter 9: Power Electronics & Logic Controls
9.1 Power Electronic Converters (Rectifiers, Inverters & DC-DC Topologies) 9.2 Inverter-Based Resources (IBRs), Grid-Forming & Grid-Following Controls 9.3 Variable Frequency Drives (VFDs), PWM Operation & Harmonic Mitigation 9.4 Boolean Algebra, Logic Gates, De Morgan's Laws & Ladder Logic Control Diagrams
10 Chapter 10: Rotating Machines — Induction & Synchronous
10.1 Three-Phase Induction Motors (Equivalent Circuits, Slip & Performance) 10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes 10.3 Synchronous Machines (Operating Principles, Power-Angle Curves & V-Curves) 10.4 Motor Starting Methods (DOL, Wye-Delta, Autotransformer, Soft-Start) & Voltage Dip
11 Chapter 11: Electric Power Devices & Renewable Energy
11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation) 11.2 Power Factor Correction Capacitors & Shunt Bank Sizing 11.3 Battery Energy Storage Systems (BESS) & Ultracapacitors 11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)
12 Chapter 12: Transmission & Distribution — Steady-State & Power Quality
12.1 Transmission Line Modeling, Voltage Drop & Conductor Sizing 12.2 Voltage Regulation, Reactive Power Support & Tap-Changer Controls 12.3 Power Quality, Harmonics, THD & IEEE 519 Compliance 12.4 Power Flow Analysis & System Stability (Steady-State, Transient & Swing Equation)
13 Chapter 13: Transmission & Distribution — Fault Analysis & Transformer Shifts
13.1 Symmetrical Three-Phase Bolted Fault Calculations 13.2 Unsymmetrical Fault Analysis (SLG, L-L, DLG Fault Calculations) 13.3 Transformer Connection Types, Zero-Sequence Paths & 30-Degree Phase Shifts
14 Chapter 14: Protection Systems & Device Coordination
14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves 14.2 Protective Relaying Schemes (Differential 87, Distance 21, Undervoltage 27) 14.3 Circuit Breakers, Fuses & Automatic Reclosers 14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)
7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition)
Key Takeaways Explain This Topic AI
Thevenin and Norton phasor equivalents reduce linear single-phase AC networks to an open-circuit voltage source (V_th) in series with a complex Thevenin impedance (Z_th = R_th + jX_th) or a short-circuit current source (I_sc = I_N) in parallel with Z_th, where Z_th = V_th / I_sc.
The Maximum Real Power Transfer Theorem for complex networks mandates a complex-conjugate load impedance (Z_L = Z_th* = R_th - jX_th), resulting in maximum power transfer P_max = |V_th|^2 / (4 R_th). For a purely resistive constrained load, R_L = |Z_th|.
Superposition requires deactivating independent sources (independent voltage sources replaced by short circuits, independent current sources by open circuits) while keeping dependent sources fully active; circuits with sources at distinct frequencies cannot have their phasors summed directly and must be analyzed in the time/instantaneous power domain.
Resonance in series RLC circuits occurs at omega_0 = 1/sqrt(LC) where circuit impedance is at a minimum (Z = R) and reactive voltages undergo magnification (V_L = V_C = Q * V_in), with quality factor Q = omega_0*L/R and fractional bandwidth BW = omega_0 / Q.
Parallel RLC resonance exhibits maximum impedance (Z = R) at omega_0 with quality factor Q = R / (omega_0 L) = omega_0 C*R, acting as a band-stop current filter.
Last updated: August 2026
7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition)
Executive Overview: Circuit analysis forms the quantitative backbone of the NCEES PE Electrical and Computer: Power examination. Questions in Domain 4 evaluate a candidate's ability to model complex single-phase AC networks in steady state using phasors, transform multi-loop networks into Thevenin/Norton equivalents, calculate maximum complex power transfer, apply superposition across linear networks, and evaluate RLC resonance phenomena. Mastering rigorous complex matrix algebra, conjugate arithmetic, and impedance transformations is essential for rapid, error-free problem solving under CBT time constraints.
1. Phasor Domain Fundamentals & Complex Impedance
In sinusoidal steady-state AC analysis, all voltages and currents oscillate at a constant angular frequency ω = 2 π f rad/s \omega = 2\pi f\text{ rad/s} ω = 2 π f rad/s . Time-domain signals v ( t ) = V p e a k cos ( ω t + θ ) v(t) = V_{peak} \cos(\omega t + \theta) v ( t ) = V p e ak cos ( ω t + θ ) are mapped into the frequency domain as root-mean-square (RMS) phasors: V = V r m s ∠ θ = V r m s e j θ = V r m s ( cos θ + j sin θ ) \mathbf{V} = V_{rms} \angle \theta = V_{rms} e^{j\theta} = V_{rms}(\cos\theta + j\sin\theta) V = V r m s ∠ θ = V r m s e j θ = V r m s ( cos θ + j sin θ )
PE Exam Standard Note: Unless explicitly stated otherwise (such as in instantaneous waveform definitions), all voltage and current magnitudes on the PE Power exam are given in RMS values .
Constitutive Branch Impedance & Admittance Relationships
Element Time-Domain Relationship Phasor Impedance ( Z \mathbf{Z} Z ) Phasor Admittance ( Y = 1 / Z \mathbf{Y} = 1/\mathbf{Z} Y = 1/ Z )
Resistor ( R R R ) v ( t ) = R i ( t ) v(t) = R \, i(t) v ( t ) = R i ( t ) Z R = R ∠ 0 ∘ = R + j 0 \mathbf{Z}_R = R \angle 0^\circ = R + j0 Z R = R ∠ 0 ∘ = R + j 0 Y R = G = 1 R \mathbf{Y}_R = G = \frac{1}{R} Y R = G = R 1
Inductor ( L L L ) v ( t ) = L d i ( t ) d t v(t) = L \frac{di(t)}{dt} v ( t ) = L d t d i ( t ) Z L = j ω L = ω L ∠ + 90 ∘ \mathbf{Z}_L = j\omega L = \omega L \angle +90^\circ Z L = jω L = ω L ∠ + 9 0 ∘ Y L = − j B L = − j 1 ω L = 1 ω L ∠ − 90 ∘ \mathbf{Y}_L = -j B_L = -j\frac{1}{\omega L} = \frac{1}{\omega L}\angle -90^\circ Y L = − j B L = − j ω L 1 = ω L 1 ∠ − 9 0 ∘
Capacitor ( C C C ) i ( t ) = C d v ( t ) d t i(t) = C \frac{dv(t)}{dt} i ( t ) = C d t d v ( t ) Z C = 1 j ω C = − j 1 ω C = 1 ω C ∠ − 90 ∘ \mathbf{Z}_C = \frac{1}{j\omega C} = -j\frac{1}{\omega C} = \frac{1}{\omega C}\angle -90^\circ Z C = jω C 1 = − j ω C 1 = ω C 1 ∠ − 9 0 ∘ Y C = + j B C = + j ω C = ω C ∠ + 90 ∘ \mathbf{Y}_C = +j B_C = +j\omega C = \omega C \angle +90^\circ Y C = + j B C = + jω C = ω C ∠ + 9 0 ∘
For any general two-terminal passive branch: Z = R + j X = ∣ Z ∣ ∠ θ Z , where ∣ Z ∣ = R 2 + X 2 , θ Z = arctan ( X R ) \mathbf{Z} = R + jX = |Z|\angle \theta_Z, \quad \text{where } |Z| = \sqrt{R^2 + X^2}, \quad \theta_Z = \arctan\left(\frac{X}{R}\right) Z = R + j X = ∣ Z ∣∠ θ Z , where ∣ Z ∣ = R 2 + X 2 , θ Z = arctan ( R X ) Y = G + j B = 1 R + j X = R − j X R 2 + X 2 = R ∣ Z ∣ 2 − j X ∣ Z ∣ 2 \mathbf{Y} = G + jB = \frac{1}{R + jX} = \frac{R - jX}{R^2 + X^2} = \frac{R}{|Z|^2} - j\frac{X}{|Z|^2} Y = G + j B = R + j X 1 = R 2 + X 2 R − j X = ∣ Z ∣ 2 R − j ∣ Z ∣ 2 X
If X > 0 X > 0 X > 0 (inductive), the current lags voltage ( θ Z > 0 \theta_Z > 0 θ Z > 0 , susceptance B < 0 B < 0 B < 0 ).
If X < 0 X < 0 X < 0 (capacitive), the current leads voltage ( θ Z < 0 \theta_Z < 0 θ Z < 0 , susceptance B > 0 B > 0 B > 0 ).
2. Thevenin & Norton Equivalent Circuits in the Phasor Domain
Any linear, active, two-terminal AC network containing independent sources, linear dependent sources, and linear passive impedances can be represented at its output terminals ( A − B A-B A − B ) by an equivalent circuit: THEVENIN EQUIVALENT CIRCUIT: NORTON EQUIVALENT CIRCUIT:
- Z_th +-----> A
- +---[ZZZZ]---+-----> A |
- | | |
- + | | +--+--+
- (~) V_th | ^ | |
- | | I_sc ( ) [Z_th]|
- | | | | |
- +------------+-----> B +--+--+
- |
- +-----> B
- Analytical Determination of Parameters
Thevenin Open-Circuit Voltage ( V t h \mathbf{V}_{th} V t h ): The phasor voltage across terminals A − B A-B A − B when the external load is disconnected ( I l o a d = 0 I_{load} = 0 I l o a d = 0 ): V t h = V o c = V A − V B \mathbf{V}_{th} = \mathbf{V}_{oc} = \mathbf{V}_A - \mathbf{V}_B V t h = V oc = V A − V B
Norton Short-Circuit Current ( I s c \mathbf{I}_{sc} I sc ): The phasor current flowing from terminal A A A to terminal B B B when terminals A − B A-B A − B are connected by an ideal zero-impedance conductor: I s c = I N = I A → B ( V A B = 0 ) \mathbf{I}_{sc} = \mathbf{I}_N = \mathbf{I}_{A \to B} \quad (V_{AB} = 0) I sc = I N = I A → B ( V A B = 0 )
Thevenin Equivalent Impedance ( Z t h \mathbf{Z}_{th} Z t h ):
General Definition (Works with all circuits, including those with dependent sources): Z t h = V t h I s c = V o c I s c \mathbf{Z}_{th} = \frac{\mathbf{V}_{th}}{\mathbf{I}_{sc}} = \frac{\mathbf{V}_{oc}}{\mathbf{I}_{sc}} Z t h = I sc V t h = I sc V oc
Independent Sources Only Method (Deactivation/Look-in Method): Deactivate all independent sources:
Replace all independent voltage sources with short circuits ( V = 0 \mathbf{V} = 0 V = 0 ).
Replace all independent current sources with open circuits ( I = 0 \mathbf{I} = 0 I = 0 ).
Calculate looking-in equivalent impedance Z i n \mathbf{Z}_{in} Z in across terminals A − B A-B A − B .
Test Source Method (For circuits containing Dependent Sources): Deactivate all independent sources, connect an external test source V t e s t \mathbf{V}_{test} V t es t (or I t e s t \mathbf{I}_{test} I t es t ) across terminals A − B A-B A − B , and calculate the resulting ratio: Z t h = V t e s t I t e s t \mathbf{Z}_{th} = \frac{\mathbf{V}_{test}}{\mathbf{I}_{test}} Z t h = I t es t V t es t
Source Transformation Relationships V t h = I s c Z t h , I N = V t h Z t h , Z N = Z t h \mathbf{V}_{th} = \mathbf{I}_{sc} \mathbf{Z}_{th}, \quad \mathbf{I}_N = \frac{\mathbf{V}_{th}}{\mathbf{Z}_{th}}, \quad \mathbf{Z}_N = \mathbf{Z}_{th} V t h = I sc Z t h , I N = Z t h V t h , Z N = Z t h
3. Maximum Power Transfer Theorem for Complex Impedances
When a linear AC source represented by Thevenin parameters V t h \mathbf{V}_{th} V t h and Z t h = R t h + j X t h \mathbf{Z}_{th} = R_{th} + jX_{th} Z t h = R t h + j X t h is connected to a variable load impedance Z L = R L + j X L \mathbf{Z}_L = R_L + jX_L Z L = R L + j X L , the complex power delivered to the load is: S L = V L I L ∗ = ∣ I L ∣ 2 Z L = ∣ V t h ( R t h + R L ) + j ( X t h + X L ) ∣ 2 ( R L + j X L ) \mathbf{S}_L = \mathbf{V}_L \mathbf{I}_L^* = |\mathbf{I}_L|^2 \mathbf{Z}_L = \left| \frac{\mathbf{V}_{th}}{(R_{th} + R_L) + j(X_{th} + X_L)} \right|^2 (R_L + jX_L) S L = V L I L ∗ = ∣ I L ∣ 2 Z L = ( R t h + R L ) + j ( X t h + X L ) V t h 2 ( R L + j X L )
The real active power dissipated in the load is: P L = ∣ I L ∣ 2 R L = ∣ V t h ∣ 2 R L ( R t h + R L ) 2 + ( X t h + X L ) 2 P_L = |\mathbf{I}_L|^2 R_L = \frac{|\mathbf{V}_{th}|^2 R_L}{(R_{th} + R_L)^2 + (X_{th} + X_L)^2} P L = ∣ I L ∣ 2 R L = ( R t h + R L ) 2 + ( X t h + X L ) 2 ∣ V t h ∣ 2 R L +---------------------------------------------------------------------------------------------------+
- | MAXIMUM REAL POWER TRANSFER CONDITIONS (PE POWER SUMMARY) |
- +-----------------------+-----------------------------------------------+---------------------------+
- | Load Constraint Type | Optimal Load Condition | Maximum Active Power |
- +-----------------------+-----------------------------------------------+---------------------------+
- | **Unconstrained** | **Complex Conjugate Match:** | |
| (Both R_L, X_L vary) | $\mathbf{Z}_L = \mathbf{Z}_{th}^* = R_{th} - jX_{th}$ | $P_{max} = \frac{|\mathbf{V}_{th}|^2}{4 R_{th}}$ |
- +-----------------------+-----------------------------------------------+---------------------------+
- | **Purely Resistive** | **Magnitude Match:** | |
| ($X_L = 0$, $R_L$ var)| $R_L = |\mathbf{Z}_{th}| = \sqrt{R_{th}^2 + X_{th}^2}$ | $P = \frac{|\mathbf{V}_{th}|^2 R_L}{(R_{th} + R_L)^2 + X_{th}^2}$ |
- +-----------------------+-----------------------------------------------+---------------------------+
- | **Fixed Load Angle** | **Magnitude Match:** | |
- | ($\theta_L$ constant) | $|\mathbf{Z}_L| = |\mathbf{Z}_{th}|$ | Dependent on $\theta_L$ |
- +-----------------------+-----------------------------------------------+---------------------------+
Critical Exam Pitfall: Under complex conjugate matching ( Z L = Z t h ∗ \mathbf{Z}_L = \mathbf{Z}_{th}^* Z L = Z t h ∗ ), the net reactance of the loop cancels entirely ( X t h + X L = X t h − X t h = 0 X_{th} + X_L = X_{th} - X_{th} = 0 X t h + X L = X t h − X t h = 0 ), driving the circuit into resonance. The load current magnitude becomes ∣ I L ∣ = ∣ V t h ∣ / ( 2 R t h ) |\mathbf{I}_L| = |\mathbf{V}_{th}| / (2 R_{th}) ∣ I L ∣ = ∣ V t h ∣/ ( 2 R t h ) . Note that total source power generated is P s o u r c e = ∣ I L ∣ 2 ( R t h + R L ) = 2 P m a x P_{source} = |\mathbf{I}_L|^2 (R_{th} + R_L) = 2 P_{max} P so u rce = ∣ I L ∣ 2 ( R t h + R L ) = 2 P ma x , representing an electrical efficiency of exactly 50 % 50\% 50% .
4. Superposition Theorem & Multi-Frequency AC Networks
The Superposition Theorem states that in any linear bilateral electrical network, the current or voltage response across any branch is equal to the algebraic sum of the individual responses produced by each independent source acting alone.
Procedural Rules for Superposition
Select one independent source at a time.
Deactivate all other independent sources:
Set independent voltage sources to zero → \rightarrow → Replace with Short Circuit .
Set independent current sources to zero → \rightarrow → Replace with Open Circuit .
Dependent sources (CCCS, CCVS, VCCS, VCVS) MUST REMAIN ACTIVE during every individual sub-circuit calculation.
Calculate the partial response phasor (e.g., V k ′ \mathbf{V}_k' V k ′ or I k ′ \mathbf{I}_k' I k ′ ).
Repeat for all independent sources.
The Frequency Superposition Boundary Rule +---------------------------------------------------------------------------------------------------+
- | SUPERPOSITION ACROSS FREQUENCIES: CRITICAL MATHEMATICAL RULES |
- |
| CASE 1: All Sources at SAME Frequency (omega_1 = omega_2):
- | -> Sum phasor quantities directly: V_total = V_1 + V_2 + ... + V_n
- | -> Compute power from final total phasor: P_total = |I_total|^2 * R
- |
| CASE 2: Sources at DIFFERENT Frequencies (omega_1 != omega_2, or DC + AC):
| -> NEVER ADD PHASORS OF DIFFERENT FREQUENCIES DIRECTLY! (Phasors rotate at different speeds).
| -> Sum responses in the TIME DOMAIN:
| v_total(t) = V_1_peak * cos(omega_1*t + theta_1) + V_2_peak * cos(omega_2*t + theta_2)
| -> Total RMS voltage across orthogonal frequencies:
| V_rms_total = sqrt( V_dc^2 + V_1_rms^2 + V_2_rms^2 + ... )
| -> Total average real power is the sum of independent average powers:
| P_total = P_1(omega_1) + P_2(omega_2) + ...
- +---------------------------------------------------------------------------------------------------+
- 5. Systematic Nodal & Mesh Analysis in the Phasor Domain
- Nodal Admittance Formulation ( [ Y ] V = I [\mathbf{Y}]\mathbf{V} = \mathbf{I} [ Y ] V = I )
For an N N N -node network with one reference node, Kirchhoff's Current Law (KCL) at each non-reference node yields the matrix equation: [ Y 11 Y 12 ⋯ Y 1 n Y 21 Y 22 ⋯ Y 2 n ⋮ ⋮ ⋱ ⋮ Y n 1 Y n 2 ⋯ Y n n ] [ V 1 V 2 ⋮ V n ] = [ I s 1 I s 2 ⋮ I s n ] \begin{bmatrix}
- \mathbf{Y}_{11} & \mathbf{Y}_{12} & \cdots & \mathbf{Y}_{1n} \\
- \mathbf{Y}_{21} & \mathbf{Y}_{22} & \cdots & \mathbf{Y}_{2n} \\
- \vdots & \vdots & \ddots & \vdots \\
- \mathbf{Y}_{n1} & \mathbf{Y}_{n2} & \cdots & \mathbf{Y}_{nn}
- \end{bmatrix}
- \begin{bmatrix}
- \mathbf{V}_1 \\
- \mathbf{V}_2 \\
- \vdots \\
- \mathbf{V}_n
- \end{bmatrix}
- =
- \begin{bmatrix}
- \mathbf{I}_{s1} \\
- \mathbf{I}_{s2} \\
- \vdots \\
- \mathbf{I}_{sn}
\end{bmatrix} Y 11 Y 21 ⋮ Y n 1 Y 12 Y 22 ⋮ Y n 2 ⋯ ⋯ ⋱ ⋯ Y 1 n Y 2 n ⋮ Y nn V 1 V 2 ⋮ V n = I s 1 I s 2 ⋮ I s n
Self-Admittance ( Y i i \mathbf{Y}_{ii} Y ii ): Sum of all branch admittances connected directly to node i i i (always positive).
Mutual Admittance ( Y i j \mathbf{Y}_{ij} Y ij ): Negative of the sum of all branch admittances connected directly between node i i i and node j j j ( Y i j = − y i j \mathbf{Y}_{ij} = -y_{ij} Y ij = − y ij ). For reciprocal networks, Y i j = Y j i \mathbf{Y}_{ij} = \mathbf{Y}_{ji} Y ij = Y ji .
Injected Node Current ( I s i \mathbf{I}_{si} I s i ): Sum of all independent source currents entering node i i i (positive if entering, negative if leaving).
Mesh Impedance Formulation ( [ Z ] I = V [\mathbf{Z}]\mathbf{I} = \mathbf{V} [ Z ] I = V )
For an M M M -mesh planar network, Kirchhoff's Voltage Law (KVL) yields: [ Z m e s h ] [ I m e s h ] = [ V s o u r c e ] [\mathbf{Z}_{mesh}][\mathbf{I}_{mesh}] = [\mathbf{V}_{source}] [ Z m es h ] [ I m es h ] = [ V so u rce ]
Self-Impedance ( Z k k \mathbf{Z}_{kk} Z kk ): Sum of all impedances around mesh k k k .
Mutual Impedance ( Z k j \mathbf{Z}_{kj} Z kj ): Negative of the impedance common to mesh k k k and mesh j j j (assuming consistent clockwise mesh current orientation).
6. Series & Parallel RLC Resonance
Resonance in an AC circuit occurs at the specific frequency ω 0 \omega_0 ω 0 where the input voltage and input current are in phase (i.e., the net reactive component of the driving-point impedance or admittance equals zero, Im { Z i n } = 0 \text{Im}\{\mathbf{Z}_{in}\} = 0 Im { Z in } = 0 , yielding a unity power factor). SERIES RLC RESONANCE: PARALLEL RLC RESONANCE:
- R L C +------+------+------+
- +-[RRR]----[LLLL]----[ | ]----+ | | | |
- | | +--+--++--+--++--+--+ |
- (~) V_in | I_in( ) |[R]| |[L]| |[C]| |
- | | +--+--++--+--++--+--+ |
- +-----------------------------+ | | | |
- +------+------+------+
- Comprehensive Comparison of Series vs. Parallel RLC Resonance
Parameter / Feature Series RLC Circuit Parallel RLC Circuit
Resonant Angular Frequency ( ω 0 \omega_0 ω 0 ) ω 0 = 1 L C rad/s \omega_0 = \frac{1}{\sqrt{LC}}\text{ rad/s} ω 0 = L C 1 rad/s ω 0 = 1 L C rad/s \omega_0 = \frac{1}{\sqrt{LC}}\text{ rad/s} ω 0 = L C 1 rad/s
Resonant Frequency ( f 0 f_0 f 0 ) f 0 = 1 2 π L C Hz f_0 = \frac{1}{2\pi\sqrt{LC}}\text{ Hz} f 0 = 2 π L C 1 Hz f 0 = 1 2 π L C Hz f_0 = \frac{1}{2\pi\sqrt{LC}}\text{ Hz} f 0 = 2 π L C 1 Hz
Input Impedance at ω 0 \omega_0 ω 0 Z ( ω 0 ) = R \mathbf{Z}(\omega_0) = R Z ( ω 0 ) = R ( Minimum ) Z ( ω 0 ) = R \mathbf{Z}(\omega_0) = R Z ( ω 0 ) = R ( Maximum )
Input Current at ω 0 \omega_0 ω 0 I ( ω 0 ) = V i n R \mathbf{I}(\omega_0) = \frac{\mathbf{V}_{in}}{R} I ( ω 0 ) = R V in ( Maximum ) I ( ω 0 ) = V i n R \mathbf{I}(\omega_0) = \frac{\mathbf{V}_{in}}{R} I ( ω 0 ) = R V in ( Minimum )
Quality Factor ( Q Q Q ) Q = ω 0 L R = 1 ω 0 C R = 1 R L C Q = \frac{\omega_0 L}{R} = \frac{1}{\omega_0 C R} = \frac{1}{R}\sqrt{\frac{L}{C}} Q = R ω 0 L = ω 0 CR 1 = R 1 C L Q = R ω 0 L = ω 0 C R = R C L Q = \frac{R}{\omega_0 L} = \omega_0 C R = R\sqrt{\frac{C}{L}} Q = ω 0 L R = ω 0 CR = R L C
Half-Power Bandwidth ( B W BW B W ) B W = Δ ω = ω 0 Q = R L rad/s BW = \Delta\omega = \frac{\omega_0}{Q} = \frac{R}{L}\text{ rad/s} B W = Δ ω = Q ω 0 = L R rad/s B W = Δ ω = ω 0 Q = 1 R C rad/s BW = \Delta\omega = \frac{\omega_0}{Q} = \frac{1}{RC}\text{ rad/s} B W = Δ ω = Q ω 0 = RC 1 rad/s
Bandwidth in Hertz ( Δ f \Delta f Δ f ) Δ f = f 0 Q = R 2 π L Hz \Delta f = \frac{f_0}{Q} = \frac{R}{2\pi L}\text{ Hz} Δ f = Q f 0 = 2 π L R Hz Δ f = f 0 Q = 1 2 π R C Hz \Delta f = \frac{f_0}{Q} = \frac{1}{2\pi R C}\text{ Hz} Δ f = Q f 0 = 2 π RC 1 Hz
Half-Power Frequencies ( ω 1 , ω 2 \omega_1, \omega_2 ω 1 , ω 2 ) ω 1 , 2 = ∓ R 2 L + ( R 2 L ) 2 + 1 L C \omega_{1,2} = \mp \frac{R}{2L} + \sqrt{\left(\frac{R}{2L}\right)^2 + \frac{1}{LC}} ω 1 , 2 = ∓ 2 L R + ( 2 L R ) 2 + L C 1 ω 1 , 2 = ∓ 1 2 R C + ( 1 2 R C ) 2 + 1 L C \omega_{1,2} = \mp \frac{1}{2RC} + \sqrt{\left(\frac{1}{2RC}\right)^2 + \frac{1}{LC}} ω 1 , 2 = ∓ 2 RC 1 + ( 2 RC 1 ) 2 + L C 1
High- Q Q Q Approximation ( Q ≥ 10 Q \ge 10 Q ≥ 10 ) ω 1 , 2 ≈ ω 0 ∓ B W 2 = ω 0 ( 1 ∓ 1 2 Q ) \omega_{1,2} \approx \omega_0 \mp \frac{BW}{2} = \omega_0 \left(1 \mp \frac{1}{2Q}\right) ω 1 , 2 ≈ ω 0 ∓ 2 B W = ω 0 ( 1 ∓ 2 Q 1 ) ω 1 , 2 ≈ ω 0 ∓ B W 2 = ω 0 ( 1 ∓ 1 2 Q ) \omega_{1,2} \approx \omega_0 \mp \frac{BW}{2} = \omega_0 \left(1 \mp \frac{1}{2Q}\right) ω 1 , 2 ≈ ω 0 ∓ 2 B W = ω 0 ( 1 ∓ 2 Q 1 )
Voltage / Current Magnification V L ( ω 0 ) = V C ( ω 0 ) = Q × V i n V_L(\omega_0) = V_C(\omega_0) = Q \times V_{in} V L ( ω 0 ) = V C ( ω 0 ) = Q × V in I L ( ω 0 ) = I C ( ω 0 ) = Q × I i n I_L(\omega_0) = I_C(\omega_0) = Q \times I_{in} I L ( ω 0 ) = I C ( ω 0 ) = Q × I in
- 7. Comprehensive Step-by-Step Worked AC Thevenin Example
- Problem Statement
An AC circuit operates at steady state with a source voltage V s = 120 ∠ 0 ∘ V (RMS) \mathbf{V}_s = 120\angle 0^\circ\text{ V (RMS)} V s = 120∠ 0 ∘ V (RMS) . The circuit consists of:
- A source-connected series branch: Z 1 = 4 + j 12 Ω \mathbf{Z}_1 = 4 + j12\,\Omega Z 1 = 4 + j 12 Ω
- A parallel shunt branch: Z 2 = − j 10 Ω \mathbf{Z}_2 = -j10\,\Omega Z 2 = − j 10 Ω
A series output branch leading to load terminals A − B A-B A − B : Z 3 = 2 + j 4 Ω \mathbf{Z}_3 = 2 + j4\,\Omega Z 3 = 2 + j 4 Ω
Determine:
The Thevenin equivalent voltage phasor V t h \mathbf{V}_{th} V t h across terminals A − B A-B A − B .
The Thevenin equivalent impedance Z t h \mathbf{Z}_{th} Z t h .
The Norton short-circuit current I s c \mathbf{I}_{sc} I sc .
The optimal load impedance Z L \mathbf{Z}_L Z L for maximum real power transfer, and the value of P m a x P_{max} P ma x . CIRCUIT SCHEMATIC:
- Z_1 = 4 + j12 ohms Z_3 = 2 + j4 ohms
- +-------[ZZZZZZ]-----------+-----------[ZZZZZZ]----------> A
- | |
- + | |
- (~) Vs = 120 /_ 0° V +--+--+
- | | | Z_2 = -j10 ohms
- | [ C ]
- | | |
- | +--+--+
- | |
- +--------------------------+------------------------------> B
Step-by-Step Numerical Solution =========================================================================================
CALCULATION WORKFLOW & SOLUTION:
=========================================================================================
Step 1: Compute Open-Circuit Thevenin Voltage (V_th)
With terminals A-B open, zero current flows through branch Z_3 (I_3 = 0).
The open-circuit voltage V_th = V_oc is the voltage across shunt impedance Z_2:
V_th = Vs * [ Z_2 / (Z_1 + Z_2) ]
Evaluate denominator:
- Z_1 + Z_2 = (4 + j12) + (-j10) = 4 + j2 ohms
- Polar form: |Z_sum| = sqrt(4^2 + 2^2) = sqrt(20) = 4.47214 ohms
- theta = arctan(2 / 4) = 26.565°
- Z_1 + Z_2 = 4.47214 /_ 26.565° ohms
Evaluate numerator:
Vs * Z_2 = (120 /_ 0°) * (10 /_ -90°) = 1200 /_ -90° V
Perform complex division:
- V_th = (1200 /_ -90°) / (4.47214 /_ 26.565°)
- = 268.328 /_ (-90° - 26.565°)
- = 268.328 /_ -116.565° V
Rectangular Conversion:
- V_th = 268.328 * cos(-116.565°) + j 268.328 * sin(-116.565°)
- = 268.328 * (-0.44721) + j 268.328 * (-0.89443)
- = -120.00 - j240.00 V
Step 2: Compute Looking-In Thevenin Impedance (Z_th)
Deactivate independent voltage source Vs (replace with short circuit).
Looking into terminals A-B:
Z_th = Z_3 + (Z_1 || Z_2)
Calculate parallel combination (Z_1 || Z_2):
- Z_p = (Z_1 * Z_2) / (Z_1 + Z_2) = (4 + j12)(-j10) / (4 + j2)
- = (120 - j40) / (4 + j2)
- = [ (120 - j40) * (4 - j2) ] / [ 4^2 + 2^2 ]
- = [ (480 - j240 - j160 - 80) ] / 20
- = (400 - j400) / 20
- = 20.00 - j20.00 ohms
Add series branch Z_3:
- Z_th = (20.00 - j20.00) + (2.00 + j4.00)
- = 22.00 - j16.00 ohms
Polar Conversion:
- |Z_th| = sqrt(22^2 + (-16)^2) = sqrt(484 + 256) = sqrt(740) = 27.203 ohms
- theta_Z = arctan(-16 / 22) = -36.027°
- Z_th = 27.203 /_ -36.027° ohms
- Step 3: Compute Norton Short-Circuit Current (I_sc)
- I_sc = V_th / Z_th
- = (268.328 /_ -116.565°) / (27.203 /_ -36.027°)
- = 9.864 /_ (-116.565° - (-36.027°))
- = 9.864 /_ -80.538° A
Rectangular Form:
- I_sc = 9.864 * cos(-80.538°) + j 9.864 * sin(-80.538°)
- = 1.622 - j9.730 A
Step 4: Determine Maximum Real Power Transfer Conditions
Optimal complex load impedance per conjugate matching:
Z_L = Z_th* = (22.00 - j16.00)* = 22.00 + j16.00 ohms (27.203 /_ +36.027° ohms)
Maximum Real Power delivered to load:
- P_max = |V_th|^2 / (4 * R_th)
- = (268.328)^2 / (4 * 22.00)
- = 72,000.0 / 88.00
- = 818.18 W
Cross-Verification via Load Current:
- I_L = V_th / (Z_th + Z_L) = (268.328 /_ -116.565°) / (22 - j16 + 22 + j16)
- = (268.328 /_ -116.565°) / 44.00 = 6.09836 /_ -116.565° A
- P_L = |I_L|^2 * R_L = (6.09836)^2 * 22.00 = 37.190 * 22.00 = 818.18 W (CONFIRMED)
- =========================================================================================
- 8. Common Exam Traps & Strategic Pitfalls
Conjugate Load Reactance Sign Inversion: Selecting Z L = Z t h \mathbf{Z}_L = \mathbf{Z}_{th} Z L = Z t h instead of Z L = Z t h ∗ \mathbf{Z}_L = \mathbf{Z}_{th}^* Z L = Z t h ∗ . If Z t h = 22 − j 16 Ω \mathbf{Z}_{th} = 22 - j16\,\Omega Z t h = 22 − j 16 Ω (capacitive), the matching load must be inductive ( Z L = 22 + j 16 Ω \mathbf{Z}_L = 22 + j16\,\Omega Z L = 22 + j 16 Ω ) to cancel source reactance and achieve resonance.
RMS vs. Peak Factor of 2 Confusion: Applying the textbook peak-voltage formula P m a x = V p e a k 2 / ( 8 R t h ) P_{max} = V_{peak}^2 / (8 R_{th}) P ma x = V p e ak 2 / ( 8 R t h ) when given RMS quantities. On the PE exam, where voltages are RMS, the denominator is 4 R t h 4 R_{th} 4 R t h .
Direct Phasor Summation Across Frequencies: Adding phasors from a 60 Hz 60\text{ Hz} 60 Hz source and a 180 Hz 180\text{ Hz} 180 Hz harmonic source directly. Phasors rotate at different angular velocities; their time waveforms must be combined or their powers summed orthogonally ( P t o t a l = P 60 + P 180 P_{total} = P_{60} + P_{180} P t o t a l = P 60 + P 180 ).
Series vs. Parallel Quality Factor Inversion: Confusing Q s e r i e s = ω 0 L R Q_{series} = \frac{\omega_0 L}{R} Q ser i es = R ω 0 L with Q p a r a l l e l = R ω 0 L Q_{parallel} = \frac{R}{\omega_0 L} Q p a r a ll e l = ω 0 L R . Note that in a series circuit, decreasing R R R increases Q Q Q , whereas in a parallel circuit, increasing R R R increases Q Q Q .