Study guide

11.2 Power Factor Correction Capacitors & Shunt Bank Sizing

PE Electrical and Computer: Power Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Strategy & Reference Handbook

1.1 PE Power Exam Format, CBT Navigation & Reference Handbook 1.2 2026 Reference Standards (NEC 2020, NFPA 70E-2021, NESC) & Scoring Mechanics 1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery

2 Chapter 2: Measurement, Metering & Field Testing

2.1 Current Transformers (CTs), Potential Transformers (PTs) & Meter Connections 2.2 Instrument Transformer Burdens, Saturation Curves & Ratio Correction Factors 2.3 Insulation Resistance Testing (Megger, Polarization Index, Dielectric Absorption) 2.4 Ground Resistance Testing (Fall-of-Potential 62% Rule & Clamp-on Methods)

3 Chapter 3: General Applications — Grounding & Surge Protection

3.1 Substation Ground Grid Design & IEEE 80 Touch/Step Voltage Criteria 3.2 Lightning Protection Systems & Rolling Sphere / Cone of Protection Methods 3.3 Surge Protective Devices (SPDs) & Voltage Surge Arresters

4 Chapter 4: General Applications — Lighting & Energy Management

4.1 Illumination Engineering & Zonal Cavity / Lumen Method Calculations 4.2 Energy Management, Demand Factors & Load Factor Calculations 4.3 Economic Dispatch, Energy Efficiency & Load Profile Analysis

5 Chapter 5: Electrical Safety & NFPA Standards

5.1 NFPA 70E Shock Protection, Approach Boundaries & PPE Requirements 5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations 5.3 Hazardous (Classified) Locations (Class I, II, III & Division/Zone Systems) 5.4 Special Occupancies & Critical Systems (NEC Articles 517 Health Care, 700/701/702 Emergency)

6 Chapter 6: NEC Wiring Methods & Installation Requirements

6.1 Conductor Ampacity & NEC Table 310.16 Derating Adjustments 6.2 Raceway Fill, Box Sizing & Conduit Bending Calculations (Chapter 9 Tables) 6.3 Equipment Grounding Conductors & Grounding Electrode Sizing (NEC Article 250)

7 Chapter 7: Circuit Analysis — Fundamentals & Symmetrical Components

7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition) 7.2 Balanced Three-Phase Circuits (Wye-Delta Configurations & Power Formulas) 7.3 Symmetrical Components & Fortescue Sequence Transformation Matrices 7.4 Sequence Impedances & Positive, Negative, Zero Sequence Network Construction

8 Chapter 8: Circuit Analysis — Per-Unit & Phasor Analysis

8.1 Per-Unit System Fundamentals & Base Conversion Formulas 8.2 Three-Phase Per-Unit Network Modeling & Equipment Impedance Conversion 8.3 Phasor Diagrams, Complex Power & Power Triangle Relationships

9 Chapter 9: Power Electronics & Logic Controls

9.1 Power Electronic Converters (Rectifiers, Inverters & DC-DC Topologies) 9.2 Inverter-Based Resources (IBRs), Grid-Forming & Grid-Following Controls 9.3 Variable Frequency Drives (VFDs), PWM Operation & Harmonic Mitigation 9.4 Boolean Algebra, Logic Gates, De Morgan's Laws & Ladder Logic Control Diagrams

10 Chapter 10: Rotating Machines — Induction & Synchronous

10.1 Three-Phase Induction Motors (Equivalent Circuits, Slip & Performance) 10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes 10.3 Synchronous Machines (Operating Principles, Power-Angle Curves & V-Curves) 10.4 Motor Starting Methods (DOL, Wye-Delta, Autotransformer, Soft-Start) & Voltage Dip

11 Chapter 11: Electric Power Devices & Renewable Energy

11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation) 11.2 Power Factor Correction Capacitors & Shunt Bank Sizing 11.3 Battery Energy Storage Systems (BESS) & Ultracapacitors 11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)

12 Chapter 12: Transmission & Distribution — Steady-State & Power Quality

12.1 Transmission Line Modeling, Voltage Drop & Conductor Sizing 12.2 Voltage Regulation, Reactive Power Support & Tap-Changer Controls 12.3 Power Quality, Harmonics, THD & IEEE 519 Compliance 12.4 Power Flow Analysis & System Stability (Steady-State, Transient & Swing Equation)

13 Chapter 13: Transmission & Distribution — Fault Analysis & Transformer Shifts

13.1 Symmetrical Three-Phase Bolted Fault Calculations 13.2 Unsymmetrical Fault Analysis (SLG, L-L, DLG Fault Calculations) 13.3 Transformer Connection Types, Zero-Sequence Paths & 30-Degree Phase Shifts

14 Chapter 14: Protection Systems & Device Coordination

14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves 14.2 Protective Relaying Schemes (Differential 87, Distance 21, Undervoltage 27) 14.3 Circuit Breakers, Fuses & Automatic Reclosers 14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)

11.2 Power Factor Correction Capacitors & Shunt Bank Sizing

Key Takeaways Explain This Topic AI

Shunt power factor correction capacitors inject leading reactive power ( Q C = ω C V 2 = 2 π f C V 2 Q_C = \omega C V^2 = 2\pi f C V^2 Q C ​ = ω C V 2 = 2 π f C V 2 ), reducing total line current, I 2 R I^2R I 2 R distribution losses, and utility penalties while releasing upstream capacity.

Bank sizing follows Q C = P ( tan ⁡ θ 1 − tan ⁡ θ 2 ) = P [ tan ⁡ ( arccos ⁡ ( PF 1 ) ) − tan ⁡ ( arccos ⁡ ( PF 2 ) ) ] Q_C = P (\tan \theta_1 - \tan \theta_2) = P [\tan(\arccos(\text{PF}_1)) - \tan(\arccos(\text{PF}_2))] Q C ​ = P ( tan θ 1 ​ − tan θ 2 ​ ) = P [ tan ( arccos ( PF 1 ​ )) − tan ( arccos ( PF 2 ​ ))] ; actual reactive output varies with voltage squared ( Q a c t = Q r a t ( V a c t / V r a t ) 2 Q_{act} = Q_{rat}(V_{act}/V_{rat})^2 Q a c t ​ = Q r a t ​ ( V a c t ​ / V r a t ​ ) 2 ).

Switching an isolated capacitor bank creates high inrush current ( I p e a k ≈ I F L 2 S s c / Q C I_{peak} \approx I_{FL}\sqrt{2S_{sc}/Q_C} I p e ak ​ ≈ I F L ​ 2 S sc ​ / Q C ​ ​ ), whereas back-to-back switching against an energized bank produces extreme high-frequency transients requiring inrush reactors.

Parallel resonance between the utility transformer inductance and capacitor bank occurs at harmonic order h r = S s c / Q C h_r = \sqrt{S_{sc}/Q_C} h r ​ = S sc ​ / Q C ​ ​ ; series detuning reactors ( 4.2 % , 5.67 % , 7 % 4.2\%, 5.67\%, 7\% 4.2% , 5.67% , 7% ) shift resonance safely below characteristic harmonic frequencies.

Capacitors applied at induction motor terminals must never exceed 90 % 90\% 90% of no-load magnetizing reactive power ( Q C ≤ 0.90 Q n l Q_C \le 0.90 \, Q_{nl} Q C ​ ≤ 0.90 Q n l ​ ) to prevent self-excitation overvoltages upon disconnection.

Last updated: August 2026

11.2 Power Factor Correction Capacitors & Shunt Bank Sizing

Executive Overview: Power factor correction (PFC) is one of the most frequently tested topics on the NCEES PE Power examination. Shunt capacitor banks supply local reactive power ( Q C Q_C Q C ​ ), cancelling inductive reactive demand from motors and transformers. Key competencies include calculating required kVAR ratings, delta vs. wye capacitance sizing, voltage sensitivity derating, evaluating inrush currents during isolated and back-to-back switching, calculating parallel harmonic resonant frequencies, applying series detuning reactors, and preventing motor self-excitation.

  • 1. Fundamentals of Power Factor Correction & Reactive Injection
  • The Power Triangle and Compensation Formulas

An uncorrected load drawing real power P P P at an initial power factor PF 1 = cos ⁡ θ 1 \text{PF}_1 = \cos \theta_1 PF 1 ​ = cos θ 1 ​ (lagging) requires apparent power S 1 S_1 S 1 ​ and reactive power Q 1 Q_1 Q 1 ​ : S 1 = P PF 1 , Q 1 = P tan ⁡ θ 1 = P tan ⁡ ( arccos ⁡ ( PF 1 ) ) = S 1 2 − P 2 S_1 = \frac{P}{\text{PF}_1}, \quad Q_1 = P \tan \theta_1 = P \tan(\arccos(\text{PF}_1)) = \sqrt{S_1^2 - P^2} S 1 ​ = PF 1 ​ P ​ , Q 1 ​ = P tan θ 1 ​ = P tan ( arccos ( PF 1 ​ )) = S 1 2 ​ − P 2 ​

To improve the power factor to a new target PF 2 = cos ⁡ θ 2 \text{PF}_2 = \cos \theta_2 PF 2 ​ = cos θ 2 ​ (lagging) without changing the active power P P P consumed by the process, a shunt capacitor bank must supply reactive power Q C Q_C Q C ​ : Q 2 = P tan ⁡ θ 2 = P tan ⁡ ( arccos ⁡ ( PF 2 ) ) Q_2 = P \tan \theta_2 = P \tan(\arccos(\text{PF}_2)) Q 2 ​ = P tan θ 2 ​ = P tan ( arccos ( PF 2 ​ )) Q C = Q 1 − Q 2 = P ( tan ⁡ θ 1 − tan ⁡ θ 2 ) Q_C = Q_1 - Q_2 = P (\tan \theta_1 - \tan \theta_2) Q C ​ = Q 1 ​ − Q 2 ​ = P ( tan θ 1 ​ − tan θ 2 ​ ) Power Factor Correction Power Triangle:

  • +---------------------- P (Constant Active Power) ----------------------->
  • | /| |
  • | / | |
  • | / | |
  • | / | |
  • | S2 / | Q2 |
  • | / | (Target) | Q1
  • | / θ2 | | (Uncorrected)
  • | S1 /-------+ |
  • | / | |
  • | / | QC = Q1 - Q2 |
  • | / θ1 | (Capacitor) |
  • V /___________|________________V
  • Three-Phase Delta vs. Wye Capacitor Bank Sizing

For a three-phase capacitor bank rated at total reactive power Q C Q_C Q C ​ on a line-to-line voltage V L L V_{LL} V LL ​ and frequency f f f :

Delta-Connected Bank (Industry Standard for ≤ 1000 V \le 1000\text{ V} ≤ 1000 V ): Each phase capacitor sees full line-to-line voltage V L L V_{LL} V LL ​ and supplies Q C , 1 ϕ = Q C / 3 Q_{C,1\phi} = Q_C / 3 Q C , 1 ϕ ​ = Q C ​ /3 : Q C , 1 ϕ = ω C Δ V L L 2 = 2 π f C Δ V L L 2 Q_{C,1\phi} = \omega C_\Delta V_{LL}^2 = 2\pi f C_\Delta V_{LL}^2 Q C , 1 ϕ ​ = ω C Δ ​ V LL 2 ​ = 2 π f C Δ ​ V LL 2 ​ C Δ = Q C 3 × 2 π f V L L 2 = Q C ω V L L 2 × 3 C_\Delta = \frac{Q_C}{3 \times 2\pi f V_{LL}^2} = \frac{Q_C}{\omega V_{LL}^2 \times 3} C Δ ​ = 3 × 2 π f V LL 2 ​ Q C ​ ​ = ω V LL 2 ​ × 3 Q C ​ ​

Wye-Connected Bank: Each phase capacitor sees line-to-neutral voltage V L N = V L L / 3 V_{LN} = V_{LL} / \sqrt{3} V L N ​ = V LL ​ / 3 ​ : Q C , 1 ϕ = ω C Y V L N 2 = ω C Y ( V L L 3 ) 2 = ω C Y V L L 2 3 Q_{C,1\phi} = \omega C_Y V_{LN}^2 = \omega C_Y \left(\frac{V_{LL}}{\sqrt{3}}\right)^2 = \frac{\omega C_Y V_{LL}^2}{3} Q C , 1 ϕ ​ = ω C Y ​ V L N 2 ​ = ω C Y ​ ( 3 ​ V LL ​ ​ ) 2 = 3 ω C Y ​ V LL 2 ​ ​ C Y = Q C 2 π f V L L 2 = 3 × C Δ C_Y = \frac{Q_C}{2\pi f V_{LL}^2} = 3 \times C_\Delta C Y ​ = 2 π f V LL 2 ​ Q C ​ ​ = 3 × C Δ ​

Exam Equivalence Rule: For the same total three-phase kVAR rating at a given voltage, a Delta-connected capacitor requires only 1 / 3 1/3 1/3 the capacitance in Microfarads ( C Δ = C Y / 3 C_\Delta = C_Y / 3 C Δ ​ = C Y ​ /3 ) of a Wye bank, but its dielectric must withstand 3 \sqrt{3} 3 ​ times higher voltage ( V L L V_{LL} V LL ​ ). Delta connections are universal in low-voltage systems because they eliminate zero-sequence harmonic circulation.

Voltage Sensitivity Derating

Capacitor reactive power output is strictly proportional to the square of the applied terminal voltage: Q a c t u a l = Q r a t e d × ( V a c t u a l V r a t e d ) 2 Q_{actual} = Q_{rated} \times \left( \frac{V_{actual}}{V_{rated}} \right)^2 Q a c t u a l ​ = Q r a t e d ​ × ( V r a t e d ​ V a c t u a l ​ ​ ) 2 I a c t u a l = I r a t e d × ( V a c t u a l V r a t e d ) I_{actual} = I_{rated} \times \left( \frac{V_{actual}}{V_{rated}} \right) I a c t u a l ​ = I r a t e d ​ × ( V r a t e d ​ V a c t u a l ​ ​ )

Example: A 100 kVAR 100\text{ kVAR} 100 kVAR , 480 V 480\text{ V} 480 V capacitor bank operating at an actual bus voltage of 460 V 460\text{ V} 460 V produces only Q a c t = 100 × ( 460 / 480 ) 2 = 91.84 kVAR Q_{act} = 100 \times (460/480)^2 = 91.84\text{ kVAR} Q a c t ​ = 100 × ( 460/480 ) 2 = 91.84 kVAR (an 8.16 % 8.16\% 8.16% capacity loss).

2. System Benefits of Power Factor Correction

Installing shunt capacitors provides measurable improvements across distribution feeders:

Feeder Line Current Reduction: I 2 = I 1 × ( PF 1 PF 2 ) I_2 = I_1 \times \left(\frac{\text{PF}_1}{\text{PF}_2}\right) I 2 ​ = I 1 ​ × ( PF 2 ​ PF 1 ​ ​ )

Conductor I 2 R I^2R I 2 R Loss Reduction: % Loss Reduction = [ 1 − ( PF 1 PF 2 ) 2 ] × 100 % \% \text{ Loss Reduction} = \left[ 1 - \left( \frac{\text{PF}_1}{\text{PF}_2} \right)^2 \right] \times 100\% % Loss Reduction = [ 1 − ( PF 2 ​ PF 1 ​ ​ ) 2 ] × 100%

Upstream Substation Transformer Released Capacity: Δ S r e l e a s e d = S 1 − S 2 = P ( 1 PF 1 − 1 PF 2 ) \Delta S_{released} = S_1 - S_2 = P \left( \frac{1}{\text{PF}_1} - \frac{1}{\text{PF}_2} \right) Δ S re l e a se d ​ = S 1 ​ − S 2 ​ = P ( PF 1 ​ 1 ​ − PF 2 ​ 1 ​ )

Feeder Voltage Drop Improvement: Δ V d r o p ≈ R P + X ( Q − Q C ) V b u s \Delta V_{drop} \approx \frac{R P + X (Q - Q_C)}{V_{bus}} Δ V d ro p ​ ≈ V b u s ​ RP + X ( Q − Q C ​ ) ​

  • 3. Switching Transients & Inrush Current Dynamics
  • Isolated Bank Energization

When energizing a single capacitor bank from an inductive utility source with short-circuit capacity S s c S_{sc} S sc ​ , the peak inrush current and natural transient frequency are: I p e a k , i s o = I F L 2 × S s c Q C = I r a t e d 2 × X C X s c I_{peak,iso} = I_{FL} \sqrt{2 \times \frac{S_{sc}}{Q_C}} = I_{rated} \sqrt{2 \times \frac{X_C}{X_{sc}}} I p e ak , i so ​ = I F L ​ 2 × Q C ​ S sc ​ ​ ​ = I r a t e d ​ 2 × X sc ​ X C ​ ​ ​ f i n r u s h = f 0 S s c Q C f_{inrush} = f_0 \sqrt{\frac{S_{sc}}{Q_C}} f in r u s h ​ = f 0 ​ Q C ​ S sc ​ ​ ​

Typical isolated bank inrush current magnitudes range from 5 – 15 × I r a t e d 5\text{--}15 \times I_{rated} 5 – 15 × I r a t e d ​ with natural frequencies of 300 – 1000 Hz 300\text{--}1000\text{ Hz} 300 – 1000 Hz .

Back-to-Back Capacitor Bank Switching

When a capacitor bank is energized on a bus where another energized capacitor bank is already connected, the energized bank acts as an instantaneous, extremely low-impedance voltage source. The high-frequency inrush current is limited only by the small inductance of the interconnecting busbar or cables ( L b u s ≈ 10 – 50 μ H L_{bus} \approx 10\text{--}50\ \mu\text{H} L b u s ​ ≈ 10 – 50 μ H ): I p e a k , b b = 2 3 V L L C 1 C 2 ( C 1 + C 2 ) L b u s I_{peak,bb} = \sqrt{\frac{2}{3}} V_{LL} \sqrt{\frac{C_1 C_2}{(C_1 + C_2) L_{bus}}} I p e ak , bb ​ = 3 2 ​ ​ V LL ​ ( C 1 ​ + C 2 ​ ) L b u s ​ C 1 ​ C 2 ​ ​ ​ f b b = 1 2 π L b u s C 1 C 2 C 1 + C 2 f_{bb} = \frac{1}{2\pi \sqrt{L_{bus} \frac{C_1 C_2}{C_1 + C_2}}} f bb ​ = 2 π L b u s ​ C 1 ​ + C 2 ​ C 1 ​ C 2 ​ ​ ​ 1 ​ Back-to-Back Switching Hazards:

  • Inrush currents reach 20x to 100x rated current
  • Transient frequencies reach 2 kHz to 10 kHz
  • Severe risk of circuit breaker contact welding and dielectric restrikes
  • MANDATORY MITIGATION: Series current-limiting inrush reactors (20 to 100 μH)
  • 4. Harmonic Resonance Hazards & Detuning Reactors
  • Parallel Resonance Mechanism

A shunt capacitor bank operates in parallel with the inductive source impedance of the upstream substation transformer ( X s c = X t x + X s y s X_{sc} = X_{tx} + X_{sys} X sc ​ = X t x ​ + X sys ​ ). At the parallel resonant frequency, the inductive and capacitive reactances cancel, creating an extremely high parallel impedance: X L ( h ) = h X s c , X C ( h ) = X C h X_L(h) = h X_{sc}, \quad X_C(h) = \frac{X_C}{h} X L ​ ( h ) = h X sc ​ , X C ​ ( h ) = h X C ​ ​ At resonance: h r X s c = X C h r ⟹ h r = X C X s c \text{At resonance: } h_r X_{sc} = \frac{X_C}{h_r} \implies h_r = \sqrt{\frac{X_C}{X_{sc}}} At resonance: h r ​ X sc ​ = h r ​ X C ​ ​ ⟹ h r ​ = X sc ​ X C ​ ​ ​

Expressing the resonant harmonic order h r h_r h r ​ in terms of short-circuit MVA and capacitor kVAR: h r = S s c Q C = k V A s c k V A R C = k V A t x Z t x , p u × k V A R C h_r = \sqrt{\frac{S_{sc}}{Q_C}} = \sqrt{\frac{kVA_{sc}}{kVAR_C}} = \sqrt{\frac{kVA_{tx}}{Z_{tx,pu} \times kVAR_C}} h r ​ = Q C ​ S sc ​ ​ ​ = kV A R C ​ kV A sc ​ ​ ​ = Z t x , p u ​ × kV A R C ​ kV A t x ​ ​ ​

If non-linear loads (such as 6-pulse VFDs or uninterruptible power supplies) inject harmonic currents near h r h_r h r ​ (e.g., h = 5 h = 5 h = 5 or h = 7 h = 7 h = 7 ), the circulating tank current magnifies by the circuit quality factor Q f a c t o r Q_{factor} Q f a c t or ​ , causing catastrophic overvoltage, fuse blowing, and capacitor rupture. Parallel Resonance Impedance Peak:

  • Impedance |Z|
  • ^
  • | /\ <-- Severe Voltage Distortion & Harmonic Amplification
  • | / \
  • | / \
  • | / \
  • | Inductive / \ Capacitive
  • | Region / \ Region
  • +---------------+------------+-------------------> Harmonic Order (h)
  • 1 h_r = sqrt(S_sc / Q_C)
  • Series Detuning Reactors (Passive De-tuning)

To prevent harmonic resonance without creating an active harmonic filter, a series iron-core or air-core reactor is placed in series with each capacitor phase. The reactor percentage p p p is defined as: p = X L X C × 100 % p = \frac{X_L}{X_C} \times 100\% p = X C ​ X L ​ ​ × 100%

The resonant tuning harmonic order h t u n e h_{tune} h t u n e ​ and tuning frequency f t u n e f_{tune} f t u n e ​ are: h t u n e = 1 p = 1 X L / X C , f t u n e = f 0 p h_{tune} = \frac{1}{\sqrt{p}} = \frac{1}{\sqrt{X_L / X_C}}, \quad f_{tune} = \frac{f_0}{\sqrt{p}} h t u n e ​ = p ​ 1 ​ = X L ​ / X C ​ ​ 1 ​ , f t u n e ​ = p ​ f 0 ​ ​

Detuning Factor ( p p p ) Tuning Frequency ( f t u n e f_{tune} f t u n e ​ ) Resonant Order ( h t u n e h_{tune} h t u n e ​ ) Target Application & Trapped Harmonics

7.0 % 7.0\% 7.0% 227 Hz 227\text{ Hz} 227 Hz 3.78 3.78 3.78 Standard for 60 Hz 60\text{ Hz} 60 Hz systems with 5th ( 300 Hz 300\text{ Hz} 300 Hz ) and 7th ( 420 Hz 420\text{ Hz} 420 Hz ) harmonics

5.67 % 5.67\% 5.67% 252 Hz 252\text{ Hz} 252 Hz 4.20 4.20 4.20 Compact de-tuning below 5th harmonic

4.2 % 4.2\% 4.2% 293 Hz 293\text{ Hz} 293 Hz 4.88 4.88 4.88 Tight de-tuning for dedicated 5th harmonic filtering

14.0 % 14.0\% 14.0% 160 Hz 160\text{ Hz} 160 Hz 2.67 2.67 2.67 Prevents resonance in systems with heavy 3rd harmonic ( 180 Hz 180\text{ Hz} 180 Hz ) content

Capacitor Voltage Rise with Series Reactor

The series reactor produces a fundamental frequency voltage boost across the capacitor terminals: V c a p = V b u s 1 − p = V b u s 1 − ( X L / X C ) V_{cap} = \frac{V_{bus}}{1 - p} = \frac{V_{bus}}{1 - (X_L / X_C)} V c a p ​ = 1 − p V b u s ​ ​ = 1 − ( X L ​ / X C ​ ) V b u s ​ ​

Critical Design Rule: When a 7 % 7\% 7% detuning reactor ( p = 0.07 p = 0.07 p = 0.07 ) is installed on a 480 V 480\text{ V} 480 V bus, the capacitor cans operate at V c a p = 480 / ( 1 − 0.07 ) = 516.1 V V_{cap} = 480 / (1 - 0.07) = 516.1\text{ V} V c a p ​ = 480/ ( 1 − 0.07 ) = 516.1 V . Standard 480 V 480\text{ V} 480 V capacitor cans will fail prematurely; engineers must specify 600 V 600\text{ V} 600 V rated capacitor cans .

5. Motor Terminal PFC & Self-Excitation Hazards

When power factor correction capacitors are connected directly across induction motor terminals (downstream of the motor contactor):

Self-Excitation Hazard

When the motor contactor opens, the spinning rotor continues turning due to mechanical load inertia. If the capacitor bank supplies more reactive power than the motor no-load magnetizing requirement ( Q C > Q n l Q_C > Q_{nl} Q C ​ > Q n l ​ ), the capacitor provides self-excitation current. The induction machine acts as a self-excited induction generator (SEIG), generating terminal voltages reaching 150 – 200 % 150\text{--}200\% 150 – 200% of rated voltage . If the contactor is reclosed out-of-phase, extreme transient torques can shatter motor shafts and couplings. Mandatory Sizing Limit: Q C ≤ 0.90 × Q n l = 0.90 × ( 3 V L L I n o − l o a d ) \text{Mandatory Sizing Limit: } Q_C \le 0.90 \times Q_{nl} = 0.90 \times (\sqrt{3} \, V_{LL} \, I_{no-load}) Mandatory Sizing Limit: Q C ​ ≤ 0.90 × Q n l ​ = 0.90 × ( 3 ​ V LL ​ I n o − l o a d ​ )

Thermal Overload Relay Sizing Adjustment

When capacitors are installed on the load side of the motor starter overload relay, the relay senses only the corrected, reduced line current I n e w I_{new} I n e w ​ : I n e w = I F L × ( PF u n c o r r e c t e d PF c o r r e c t e d ) I_{new} = I_{FL} \times \left( \frac{\text{PF}_{uncorrected}}{\text{PF}_{corrected}} \right) I n e w ​ = I F L ​ × ( PF correc t e d ​ PF u n correc t e d ​ ​ )

Exam Trap: Overload thermal heaters must be resized downward based on I n e w I_{new} I n e w ​ . If the original full-load current rating is retained, the motor loses all thermal overload protection against mechanical stalls.

  • 6. Comprehensive Worked PFC & Resonance Calculation
  • Problem Statement

An industrial manufacturing facility operates a balanced three-phase load of P = 2 , 000 kW P = 2,000\text{ kW} P = 2 , 000 kW at 480 V 480\text{ V} 480 V , 60 Hz 60\text{ Hz} 60 Hz , with an uncorrected power factor of PF 1 = 0.72 \text{PF}_1 = 0.72 PF 1 ​ = 0.72 lagging. The facility is served by a 2 , 500 kVA 2,500\text{ kVA} 2 , 500 kVA , 13.8 kV / 480 V 13.8\text{ kV} / 480\text{ V} 13.8 kV /480 V transformer with impedance Z = 5.75 % Z = 5.75\% Z = 5.75% .

Calculate:

The required capacitor bank rating ( Q C Q_C Q C ​ ) in kVAR to achieve a corrected power factor of PF 2 = 0.95 \text{PF}_2 = 0.95 PF 2 ​ = 0.95 lagging.

The per-phase capacitance in Microfarads ( μ F \mu\text{F} μ F ) for a Delta-connected capacitor bank.

The released transformer capacity ( Δ S \Delta S Δ S ) in kVA and the percentage reduction in feeder I 2 R I^2R I 2 R copper losses.

The parallel resonant harmonic order ( h r h_r h r ​ ) created by this installation.

The fundamental voltage across the capacitor cans if a 7.0 % 7.0\% 7.0% series detuning reactor is installed.

Step-by-Step Solution

Step 1: Required Reactive Power Compensation ( Q C Q_C Q C ​ ) θ 1 = arccos ⁡ ( 0.72 ) = 43.946 ∘ ⟹ tan ⁡ θ 1 = tan ⁡ ( 43.946 ∘ ) = 0.96394 \theta_1 = \arccos(0.72) = 43.946^\circ \implies \tan \theta_1 = \tan(43.946^\circ) = 0.96394 θ 1 ​ = arccos ( 0.72 ) = 43.94 6 ∘ ⟹ tan θ 1 ​ = tan ( 43.94 6 ∘ ) = 0.96394 θ 2 = arccos ⁡ ( 0.95 ) = 18.195 ∘ ⟹ tan ⁡ θ 2 = tan ⁡ ( 18.195 ∘ ) = 0.32868 \theta_2 = \arccos(0.95) = 18.195^\circ \implies \tan \theta_2 = \tan(18.195^\circ) = 0.32868 θ 2 ​ = arccos ( 0.95 ) = 18.19 5 ∘ ⟹ tan θ 2 ​ = tan ( 18.19 5 ∘ ) = 0.32868 Q C = P ( tan ⁡ θ 1 − tan ⁡ θ 2 ) = 2 , 000 kW × ( 0.96394 − 0.32868 ) = 2 , 000 × 0.63526 = 1 , 270.5 kVAR Q_C = P (\tan \theta_1 - \tan \theta_2) = 2,000\text{ kW} \times (0.96394 - 0.32868) = 2,000 \times 0.63526 = 1,270.5\text{ kVAR} Q C ​ = P ( tan θ 1 ​ − tan θ 2 ​ ) = 2 , 000 kW × ( 0.96394 − 0.32868 ) = 2 , 000 × 0.63526 = 1 , 270.5 kVAR Standard Bank Size: Q C = 1 , 270 kVAR \text{Standard Bank Size: } Q_C = 1,270\text{ kVAR} Standard Bank Size: Q C ​ = 1 , 270 kVAR

Step 2: Delta-Connected Capacitance per Phase Q C , 1 ϕ = 1 , 270.5 kVAR 3 = 423.5 kVAR = 423 , 500 VAR Q_{C,1\phi} = \frac{1,270.5\text{ kVAR}}{3} = 423.5\text{ kVAR} = 423,500\text{ VAR} Q C , 1 ϕ ​ = 3 1 , 270.5 kVAR ​ = 423.5 kVAR = 423 , 500 VAR C Δ = Q C , 1 ϕ 2 π f V L L 2 = 423 , 500 VAR 2 π ( 60 Hz ) ( 480 V ) 2 = 423 , 500 376.991 × 230 , 400 = 423 , 500 86 , 858 , 726 = 4.876 × 10 − 3 F = 4 , 876 μ F C_\Delta = \frac{Q_{C,1\phi}}{2\pi f V_{LL}^2} = \frac{423,500\text{ VAR}}{2\pi (60\text{ Hz})(480\text{ V})^2} = \frac{423,500}{376.991 \times 230,400} = \frac{423,500}{86,858,726} = 4.876 \times 10^{-3}\text{ F} = 4,876\ \mu\text{F} C Δ ​ = 2 π f V LL 2 ​ Q C , 1 ϕ ​ ​ = 2 π ( 60 Hz ) ( 480 V ) 2 423 , 500 VAR ​ = 376.991 × 230 , 400 423 , 500 ​ = 86 , 858 , 726 423 , 500 ​ = 4.876 × 1 0 − 3 F = 4 , 876 μ F

Step 3: Released Capacity & Loss Reduction S 1 = 2 , 000 kW 0.72 = 2 , 777.8 kVA , S 2 = 2 , 000 kW 0.95 = 2 , 105.3 kVA S_1 = \frac{2,000\text{ kW}}{0.72} = 2,777.8\text{ kVA}, \quad S_2 = \frac{2,000\text{ kW}}{0.95} = 2,105.3\text{ kVA} S 1 ​ = 0.72 2 , 000 kW ​ = 2 , 777.8 kVA , S 2 ​ = 0.95 2 , 000 kW ​ = 2 , 105.3 kVA Δ S r e l e a s e d = S 1 − S 2 = 2 , 777.8 − 2 , 105.3 = 672.5 kVA \Delta S_{released} = S_1 - S_2 = 2,777.8 - 2,105.3 = 672.5\text{ kVA} Δ S re l e a se d ​ = S 1 ​ − S 2 ​ = 2 , 777.8 − 2 , 105.3 = 672.5 kVA % Loss Reduction = [ 1 − ( 0.72 0.95 ) 2 ] × 100 % = [ 1 − 0.5744 ] × 100 % = 42.56 % \% \text{ Loss Reduction} = \left[ 1 - \left(\frac{0.72}{0.95}\right)^2 \right] \times 100\% = [1 - 0.5744] \times 100\% = 42.56\% % Loss Reduction = [ 1 − ( 0.95 0.72 ​ ) 2 ] × 100% = [ 1 − 0.5744 ] × 100% = 42.56%

Step 4: Parallel Resonant Harmonic Order Transformer Short-Circuit Capacity: S s c = S t x Z t x , p u = 2 , 500 kVA 0.0575 = 43 , 478.3 kVA = 43.48 MVA S_{sc} = \frac{S_{tx}}{Z_{tx,pu}} = \frac{2,500\text{ kVA}}{0.0575} = 43,478.3\text{ kVA} = 43.48\text{ MVA} S sc ​ = Z t x , p u ​ S t x ​ ​ = 0.0575 2 , 500 kVA ​ = 43 , 478.3 kVA = 43.48 MVA h r = S s c Q C = 43 , 478.3 kVA 1 , 270.5 kVAR = 34.22 = 5.85 h_r = \sqrt{\frac{S_{sc}}{Q_C}} = \sqrt{\frac{43,478.3\text{ kVA}}{1,270.5\text{ kVAR}}} = \sqrt{34.22} = 5.85 h r ​ = Q C ​ S sc ​ ​ ​ = 1 , 270.5 kVAR 43 , 478.3 kVA ​ ​ = 34.22 ​ = 5.85

Resonance Assessment: Resonant harmonic order h r = 5.85 h_r = 5.85 h r ​ = 5.85 lies directly between the 5th ( h = 5 h = 5 h = 5 ) and 7th ( h = 7 h = 7 h = 7 ) characteristic harmonics generated by 6-pulse non-linear drives. Under minor load variations, h r h_r h r ​ will shift directly onto the 5th harmonic, causing massive harmonic current amplification.

Step 5: Detuning Reactor Selection and Capacitor Voltage Rise Applying a p = 7.0 % p = 7.0\% p = 7.0% series detuning reactor ( p = 0.07 p = 0.07 p = 0.07 ): h t u n e = 1 0.07 = 3.78 ⟹ f t u n e = 3.78 × 60 Hz = 226.8 Hz h_{tune} = \frac{1}{\sqrt{0.07}} = 3.78 \implies f_{tune} = 3.78 \times 60\text{ Hz} = 226.8\text{ Hz} h t u n e ​ = 0.07 ​ 1 ​ = 3.78 ⟹ f t u n e ​ = 3.78 × 60 Hz = 226.8 Hz

Because 226.8 Hz < 300 Hz 226.8\text{ Hz} < 300\text{ Hz} 226.8 Hz < 300 Hz (5th harmonic), the bank behaves inductively at all harmonic frequencies ( h ≥ 5 h \ge 5 h ≥ 5 ), completely eliminating parallel resonance.

Capacitor terminal voltage with 7 % 7\% 7% reactor: V c a p = V b u s 1 − p = 480 V 1 − 0.07 = 480 V 0.93 = 516.13 V V_{cap} = \frac{V_{bus}}{1 - p} = \frac{480\text{ V}}{1 - 0.07} = \frac{480\text{ V}}{0.93} = 516.13\text{ V} V c a p ​ = 1 − p V b u s ​ ​ = 1 − 0.07 480 V ​ = 0.93 480 V ​ = 516.13 V

Capacitor cans must be specified with a minimum voltage rating of 600 V 600\text{ V} 600 V .

7. Common Exam Traps & Strategic Pitfalls

Delta vs. Wye Microfarad Inversion: Remember that C Y = 3 × C Δ C_Y = 3 \times C_\Delta C Y ​ = 3 × C Δ ​ . If asked for Delta capacitance, dividing the total three-phase kVAR by ω V L L 2 \omega V_{LL}^2 ω V LL 2 ​ without dividing by 3 will produce an answer 3 times too large.

Overcurrent Protection Sizing per NEC 460.8(B): Conductor ampacity supplying capacitor banks must not be less than 135 % 135\% 135% of the rated capacitor current .

Residual Discharge Resistors (NEC 460.6): Capacitors rated ≤ 600 V \le 600\text{ V} ≤ 600 V must discharge stored voltage to ≤ 50 V \le 50\text{ V} ≤ 50 V within 1 minute after de-energization; capacitors > 600 V > 600\text{ V} > 600 V must discharge to ≤ 50 V \le 50\text{ V} ≤ 50 V within 5 minutes .

Loading diagram... Power Factor Correction and Harmonic Detuning Filter Architecture