Study guide
11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation)
PE Electrical and Computer: Power Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Strategy & Reference Handbook
1.1 PE Power Exam Format, CBT Navigation & Reference Handbook 1.2 2026 Reference Standards (NEC 2020, NFPA 70E-2021, NESC) & Scoring Mechanics 1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery
2 Chapter 2: Measurement, Metering & Field Testing
2.1 Current Transformers (CTs), Potential Transformers (PTs) & Meter Connections 2.2 Instrument Transformer Burdens, Saturation Curves & Ratio Correction Factors 2.3 Insulation Resistance Testing (Megger, Polarization Index, Dielectric Absorption) 2.4 Ground Resistance Testing (Fall-of-Potential 62% Rule & Clamp-on Methods)
3 Chapter 3: General Applications — Grounding & Surge Protection
3.1 Substation Ground Grid Design & IEEE 80 Touch/Step Voltage Criteria 3.2 Lightning Protection Systems & Rolling Sphere / Cone of Protection Methods 3.3 Surge Protective Devices (SPDs) & Voltage Surge Arresters
4 Chapter 4: General Applications — Lighting & Energy Management
4.1 Illumination Engineering & Zonal Cavity / Lumen Method Calculations 4.2 Energy Management, Demand Factors & Load Factor Calculations 4.3 Economic Dispatch, Energy Efficiency & Load Profile Analysis
5 Chapter 5: Electrical Safety & NFPA Standards
5.1 NFPA 70E Shock Protection, Approach Boundaries & PPE Requirements 5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations 5.3 Hazardous (Classified) Locations (Class I, II, III & Division/Zone Systems) 5.4 Special Occupancies & Critical Systems (NEC Articles 517 Health Care, 700/701/702 Emergency)
6 Chapter 6: NEC Wiring Methods & Installation Requirements
6.1 Conductor Ampacity & NEC Table 310.16 Derating Adjustments 6.2 Raceway Fill, Box Sizing & Conduit Bending Calculations (Chapter 9 Tables) 6.3 Equipment Grounding Conductors & Grounding Electrode Sizing (NEC Article 250)
7 Chapter 7: Circuit Analysis — Fundamentals & Symmetrical Components
7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition) 7.2 Balanced Three-Phase Circuits (Wye-Delta Configurations & Power Formulas) 7.3 Symmetrical Components & Fortescue Sequence Transformation Matrices 7.4 Sequence Impedances & Positive, Negative, Zero Sequence Network Construction
8 Chapter 8: Circuit Analysis — Per-Unit & Phasor Analysis
8.1 Per-Unit System Fundamentals & Base Conversion Formulas 8.2 Three-Phase Per-Unit Network Modeling & Equipment Impedance Conversion 8.3 Phasor Diagrams, Complex Power & Power Triangle Relationships
9 Chapter 9: Power Electronics & Logic Controls
9.1 Power Electronic Converters (Rectifiers, Inverters & DC-DC Topologies) 9.2 Inverter-Based Resources (IBRs), Grid-Forming & Grid-Following Controls 9.3 Variable Frequency Drives (VFDs), PWM Operation & Harmonic Mitigation 9.4 Boolean Algebra, Logic Gates, De Morgan's Laws & Ladder Logic Control Diagrams
10 Chapter 10: Rotating Machines — Induction & Synchronous
10.1 Three-Phase Induction Motors (Equivalent Circuits, Slip & Performance) 10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes 10.3 Synchronous Machines (Operating Principles, Power-Angle Curves & V-Curves) 10.4 Motor Starting Methods (DOL, Wye-Delta, Autotransformer, Soft-Start) & Voltage Dip
11 Chapter 11: Electric Power Devices & Renewable Energy
11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation) 11.2 Power Factor Correction Capacitors & Shunt Bank Sizing 11.3 Battery Energy Storage Systems (BESS) & Ultracapacitors 11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)
12 Chapter 12: Transmission & Distribution — Steady-State & Power Quality
12.1 Transmission Line Modeling, Voltage Drop & Conductor Sizing 12.2 Voltage Regulation, Reactive Power Support & Tap-Changer Controls 12.3 Power Quality, Harmonics, THD & IEEE 519 Compliance 12.4 Power Flow Analysis & System Stability (Steady-State, Transient & Swing Equation)
13 Chapter 13: Transmission & Distribution — Fault Analysis & Transformer Shifts
13.1 Symmetrical Three-Phase Bolted Fault Calculations 13.2 Unsymmetrical Fault Analysis (SLG, L-L, DLG Fault Calculations) 13.3 Transformer Connection Types, Zero-Sequence Paths & 30-Degree Phase Shifts
14 Chapter 14: Protection Systems & Device Coordination
14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves 14.2 Protective Relaying Schemes (Differential 87, Distance 21, Undervoltage 27) 14.3 Circuit Breakers, Fuses & Automatic Reclosers 14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)
11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation)
Key Takeaways Explain This Topic AI
A two-winding transformer turns ratio a = N 1 / N 2 = V 1 / V 2 = I 2 / I 1 a = N_1/N_2 = V_1/V_2 = I_2/I_1 a = N 1 / N 2 = V 1 / V 2 = I 2 / I 1 allows impedance referral across windings using Z 1 = a 2 Z 2 Z_1 = a^2 Z_2 Z 1 = a 2 Z 2 ; autotransformers deliver power through combined conduction and induction ( S t r a n s f e r r e d = S r a t e d ( 1 − 1 / a ) S_{transferred} = S_{rated}(1 - 1/a) S t r an s f erre d = S r a t e d ( 1 − 1/ a ) ).
The per-phase equivalent circuit separates shunt core excitation parameters ( R c , X m R_c, X_m R c , X m , from Open-Circuit test at rated voltage) from series winding impedances ( R e q , X e q R_{eq}, X_{eq} R e q , X e q , from Short-Circuit test at rated current).
Voltage regulation quantifies terminal voltage variation from no-load to full-load ( V R % = ∣ V N L ∣ − ∣ V F L ∣ ∣ V F L ∣ × 100 % VR\% = \frac{|V_{NL}| - |V_{FL}|}{|V_{FL}|} \times 100\% V R % = ∣ V F L ∣ ∣ V N L ∣ − ∣ V F L ∣ × 100% ); lagging loads cause voltage drop, whereas leading loads can yield negative regulation (voltage rise).
Maximum operating efficiency occurs at the exact load fraction x = P c o r e / P c u , F L x = \sqrt{P_{core}/P_{cu,FL}} x = P core / P c u , F L where variable I 2 R I^2R I 2 R copper losses equal constant core losses ( P c u = P c o r e P_{cu} = P_{core} P c u = P core ).
Dissolved Gas Analysis (DGA per IEEE C57.104) identifies internal transformer failure modes: H 2 H_2 H 2 (corona), C H 4 / C 2 H 6 CH_4/C_2H_6 C H 4 / C 2 H 6 (low/medium thermal oil breakdown), C 2 H 4 C_2H_4 C 2 H 4 (high-temp oil overheating), C 2 H 2 C_2H_2 C 2 H 2 (dielectric arcing), and C O / C O 2 CO/CO_2 CO / C O 2 (cellulose insulation decomposition).
Last updated: August 2026
11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation)
Executive Overview: Power transformers are the central electromagnetic links in electrical power transmission and distribution networks. On the NCEES PE Power examination, transformer questions evaluate quantitative mastery of turns ratio conversions, per-phase equivalent circuit parameter extraction from standard laboratory tests (Open-Circuit and Short-Circuit tests), full-load voltage regulation under lagging and leading power factors, load-dependent efficiency calculations, autotransformer power magnification, and condition assessment diagnostics including Dissolved Gas Analysis (DGA).
- 1. Transformer Construction, Turns Ratio, Polarity & Autotransformers
- Turns Ratio and Impedance Referral
An ideal two-winding transformer relates primary and secondary voltages, currents, and impedances through the turns ratio a a a : a = N 1 N 2 = V 1 V 2 = I 2 I 1 a = \frac{N_1}{N_2} = \frac{V_1}{V_2} = \frac{I_2}{I_1} a = N 2 N 1 = V 2 V 1 = I 1 I 2
When transferring circuit impedances from one side of the transformer to the other:
Referring Secondary Impedance to Primary (High-to-Low or Low-to-High): Z 2 ′ = a 2 Z 2 = ( N 1 N 2 ) 2 Z 2 Z_2' = a^2 Z_2 = \left(\frac{N_1}{N_2}\right)^2 Z_2 Z 2 ′ = a 2 Z 2 = ( N 2 N 1 ) 2 Z 2
Referring Primary Impedance to Secondary: Z 1 ′ = Z 1 a 2 = ( N 2 N 1 ) 2 Z 1 Z_1' = \frac{Z_1}{a^2} = \left(\frac{N_2}{N_1}\right)^2 Z_1 Z 1 ′ = a 2 Z 1 = ( N 1 N 2 ) 2 Z 1 Primary Side (N1) Secondary Side (N2)
- o-------+ +-------o
- ) (
- V1 ( N1 N2 ) V2
- ) (
- o-------+ +-------o
Impedance Referral Rule:
- Move from LV to HV => Multiply impedance by a^2 (Z increases)
- Move from HV to LV => Divide impedance by a^2 (Z decreases)
- Terminal Polarity: Subtractive vs. Additive
Transformer polarity indicates the relative instantaneous direction of induced voltages between high-voltage (HV, labeled H 1 , H 2 H_1, H_2 H 1 , H 2 ) and low-voltage (LV, labeled X 1 , X 2 X_1, X_2 X 1 , X 2 ) terminals:
Subtractive Polarity: H 1 H_1 H 1 and X 1 X_1 X 1 are adjacent (on the same side). If H 1 H_1 H 1 and X 1 X_1 X 1 are connected together and voltage V H 1 − H 2 V_{H1-H2} V H 1 − H 2 is applied, the voltage measured across the remaining terminals is V t e s t = V H V − V L V V_{test} = V_{HV} - V_{LV} V t es t = V H V − V L V .
Additive Polarity: H 1 H_1 H 1 and X 1 X_1 X 1 are diagonally opposite ( H 1 H_1 H 1 adjacent to X 2 X_2 X 2 ). The test voltage is V t e s t = V H V + V L V V_{test} = V_{HV} + V_{LV} V t es t = V H V + V L V .
Polarity Type Terminal Layout Standard Practice (IEEE C57.12.00)
Subtractive H 1 H_1 H 1 directly opposite X 1 X_1 X 1 All single-phase units > 200 kVA > 200\text{ kVA} > 200 kVA , OR any unit with HV rating > 8 , 660 V > 8,660\text{ V} > 8 , 660 V
Additive H 1 H_1 H 1 diagonally opposite X 1 X_1 X 1 Single-phase units ≤ 200 kVA \le 200\text{ kVA} ≤ 200 kVA AND HV rating ≤ 8 , 660 V \le 8,660\text{ V} ≤ 8 , 660 V
Autotransformers & Power Magnification
An autotransformer connects the primary and secondary windings in series, sharing a common section of winding. Because part of the energy transfers through direct electrical conduction rather than purely magnetic induction, an autotransformer exhibits significantly higher apparent power throughput for a given physical core size.
For a step-down autotransformer with high-voltage V H V_H V H and low-voltage V X V_X V X ( a a u t o = V H / V X > 1 a_{auto} = V_H / V_X > 1 a a u t o = V H / V X > 1 ): S a u t o = S t w o − w i n d i n g × V H V H − V X = S 2 w × a a u t o a a u t o − 1 S_{auto} = S_{two-winding} \times \frac{V_H}{V_H - V_X} = S_{2w} \times \frac{a_{auto}}{a_{auto} - 1} S a u t o = S tw o − w in d in g × V H − V X V H = S 2 w × a a u t o − 1 a a u t o
The total power throughput decomposes into two components:
Transformed (Inductive) Power: Transferred magnetically through the core: S i n d = S a u t o ( 1 − 1 a a u t o ) = S 2 w S_{ind} = S_{auto} \left(1 - \frac{1}{a_{auto}}\right) = S_{2w} S in d = S a u t o ( 1 − a a u t o 1 ) = S 2 w
Conducted Power: Transferred directly through electrical connection: S c o n d = S a u t o − S i n d = S a u t o ( 1 a a u t o ) S_{cond} = S_{auto} - S_{ind} = S_{auto} \left(\frac{1}{a_{auto}}\right) S co n d = S a u t o − S in d = S a u t o ( a a u t o 1 )
Exam Key Point: When turns ratio a a u t o a_{auto} a a u t o is close to 1.0 (e.g., 13.8 kV 13.8\text{ kV} 13.8 kV to 12.47 kV 12.47\text{ kV} 12.47 kV , a = 1.107 a = 1.107 a = 1.107 ), over 90 % 90\% 90% of power is conducted directly. This yields minimal losses, high efficiency ( > 99.5 % >99.5\% > 99.5% ), and extremely low impedance, but eliminates electrical isolation between primary and secondary circuits.
2. Per-Phase Equivalent Circuit & Standard Parameter Tests
The complete single-phase equivalent circuit of a real power transformer includes winding resistances ( R 1 , R 2 R_1, R_2 R 1 , R 2 ), leakage reactances ( X 1 , X 2 X_1, X_2 X 1 , X 2 ), core loss resistance ( R c R_c R c ), and magnetizing reactance ( X m X_m X m ). R1 X1 R2' X2'
- o---[####]------[UUUU]---+---------+----[####]------[UUUU]---o
- | |
- [ ] Rc [ ] jXm
- [ ] [ ]
- | |
- o------------------------+---------+-------------------------o
In standard power engineering analysis, the shunt excitation branch is moved to the input terminals, and series components are lumped into equivalent values referred to either the primary or secondary: R e q 1 = R 1 + a 2 R 2 , X e q 1 = X 1 + a 2 X 2 , Z e q 1 = R e q 1 + j X e q 1 R_{eq1} = R_1 + a^2 R_2, \quad X_{eq1} = X_1 + a^2 X_2, \quad Z_{eq1} = R_{eq1} + j X_{eq1} R e q 1 = R 1 + a 2 R 2 , X e q 1 = X 1 + a 2 X 2 , Z e q 1 = R e q 1 + j X e q 1 R e q 2 = R 1 a 2 + R 2 , X e q 2 = X 1 a 2 + X 2 , Z e q 2 = R e q 2 + j X e q 2 R_{eq2} = \frac{R_1}{a^2} + R_2, \quad X_{eq2} = \frac{X_1}{a^2} + X_2, \quad Z_{eq2} = R_{eq2} + j X_{eq2} R e q 2 = a 2 R 1 + R 2 , X e q 2 = a 2 X 1 + X 2 , Z e q 2 = R e q 2 + j X e q 2
Open-Circuit (No-Load) Test
Setup: Performed at rated voltage on the Low-Voltage (LV) winding with the High-Voltage (HV) winding left open-circuit (for safety and instrumentation availability).
Measurements: Open-circuit voltage V o c = V r a t e d , L V V_{oc} = V_{rated,LV} V oc = V r a t e d , L V , no-load current I o c I_{oc} I oc , and no-load power P o c P_{oc} P oc .
Extracted Parameters (Core Excitation Branch referred to LV): Core Loss Resistance: R c , L V = V o c 2 P o c \text{Core Loss Resistance: } R_{c,LV} = \frac{V_{oc}^2}{P_{oc}} Core Loss Resistance: R c , L V = P oc V oc 2 Core Loss Current: I c = P o c V o c \text{Core Loss Current: } I_c = \frac{P_{oc}}{V_{oc}} Core Loss Current: I c = V oc P oc Magnetizing Current: I m = I o c 2 − I c 2 \text{Magnetizing Current: } I_m = \sqrt{I_{oc}^2 - I_c^2} Magnetizing Current: I m = I oc 2 − I c 2 Magnetizing Reactance: X m , L V = V o c I m = V o c I o c 2 − ( P o c / V o c ) 2 \text{Magnetizing Reactance: } X_{m,LV} = \frac{V_{oc}}{I_m} = \frac{V_{oc}}{\sqrt{I_{oc}^2 - (P_{oc}/V_{oc})^2}} Magnetizing Reactance: X m , L V = I m V oc = I oc 2 − ( P oc / V oc ) 2 V oc
Short-Circuit Test
Setup: Performed at rated current on the High-Voltage (HV) winding with the Low-Voltage (LV) winding bolted short-circuited.
Measurements: Short-circuit voltage V s c V_{sc} V sc (typically 3 – 8 % 3\text{--}8\% 3 – 8% of rated V H V V_{HV} V H V ), rated current I s c = I r a t e d , H V I_{sc} = I_{rated,HV} I sc = I r a t e d , H V , and short-circuit power P s c P_{sc} P sc .
Extracted Parameters (Series Winding Impedance referred to HV): Equivalent Resistance: R e q , H V = P s c I s c 2 \text{Equivalent Resistance: } R_{eq,HV} = \frac{P_{sc}}{I_{sc}^2} Equivalent Resistance: R e q , H V = I sc 2 P sc Equivalent Impedance Magnitude: Z e q , H V = V s c I s c \text{Equivalent Impedance Magnitude: } Z_{eq,HV} = \frac{V_{sc}}{I_{sc}} Equivalent Impedance Magnitude: Z e q , H V = I sc V sc Equivalent Leakage Reactance: X e q , H V = Z e q , H V 2 − R e q , H V 2 \text{Equivalent Leakage Reactance: } X_{eq,HV} = \sqrt{Z_{eq,HV}^2 - R_{eq,HV}^2} Equivalent Leakage Reactance: X e q , H V = Z e q , H V 2 − R e q , H V 2
3. Voltage Regulation & Phasor Dynamics
Transformer Voltage Regulation ( V R % VR\% V R % ) is the percentage change in secondary terminal voltage magnitude from no-load ( V N L V_{NL} V N L ) to full-load ( V F L V_{FL} V F L ) under a constant primary supply voltage: V R % = ∣ V N L ∣ − ∣ V F L ∣ ∣ V F L ∣ × 100 % = ∣ V 1 / a ∣ − ∣ V 2 , F L ∣ ∣ V 2 , F L ∣ × 100 % VR\% = \frac{|V_{NL}| - |V_{FL}|}{|V_{FL}|} \times 100\% = \frac{|V_1/a| - |V_{2,FL}|}{|V_{2,FL}|} \times 100\% V R % = ∣ V F L ∣ ∣ V N L ∣ − ∣ V F L ∣ × 100% = ∣ V 2 , F L ∣ ∣ V 1 / a ∣ − ∣ V 2 , F L ∣ × 100%
Approximate Formula (Kapp Regulation Formula)
Using the equivalent circuit referred to the secondary winding: V R % ≈ I 2 ( R e q 2 cos θ 2 ± X e q 2 sin θ 2 ) V 2 , F L × 100 % VR\% \approx \frac{I_2 (R_{eq2} \cos \theta_2 \pm X_{eq2} \sin \theta_2)}{V_{2,FL}} \times 100\% V R % ≈ V 2 , F L I 2 ( R e q 2 cos θ 2 ± X e q 2 sin θ 2 ) × 100%
In per-unit notation: V R % ≈ [ R p u cos θ ± X p u sin θ + 1 2 ( X p u cos θ ∓ R p u sin θ ) 2 ] × 100 % VR\% \approx \left[ R_{pu} \cos \theta \pm X_{pu} \sin \theta + \frac{1}{2} (X_{pu} \cos \theta \mp R_{pu} \sin \theta)^2 \right] \times 100\% V R % ≈ [ R p u cos θ ± X p u sin θ + 2 1 ( X p u cos θ ∓ R p u sin θ ) 2 ] × 100%
Where the sign convention is:
+ + + (Plus): Lagging (inductive) load power factor.
− - − (Minus): Leading (capacitive) load power factor. Voltage Regulation Behavior vs Power Factor:
- Lagging PF (Inductive): VR% > 0 (V_FL < V_NL => Terminal voltage drops under load)
- Unity PF (Resistive): VR% > 0 (Small positive drop due to Req)
- Leading PF (Capacitive): VR% can be < 0 (V_FL > V_NL => Terminal voltage rises under load!)
Zero Voltage Regulation Condition: Voltage regulation equals exactly zero when R e q 2 cos θ = X e q 2 sin θ R_{eq2} \cos \theta = X_{eq2} \sin \theta R e q 2 cos θ = X e q 2 sin θ , which occurs at a leading power factor angle of θ = arctan ( R e q / X e q ) \theta = \arctan(R_{eq}/X_{eq}) θ = arctan ( R e q / X e q ) .
4. Efficiency & Condition for Maximum Efficiency
Transformer efficiency η \eta η is the ratio of active output power to active input power: η = P o u t P i n = P o u t P o u t + P l o s s = x S r a t e d cos θ x S r a t e d cos θ + P c o r e + x 2 P c u , F L \eta = \frac{P_{out}}{P_{in}} = \frac{P_{out}}{P_{out} + P_{loss}} = \frac{x \, S_{rated} \cos \theta}{x \, S_{rated} \cos \theta + P_{core} + x^2 P_{cu,FL}} η = P in P o u t = P o u t + P l oss P o u t = x S r a t e d cos θ + P core + x 2 P c u , F L x S r a t e d cos θ
Where:
x = S l o a d / S r a t e d x = S_{load} / S_{rated} x = S l o a d / S r a t e d is the per-unit load fraction ( 0 ≤ x ≤ 1.0 0 \le x \le 1.0 0 ≤ x ≤ 1.0 ).
P c o r e = P o c P_{core} = P_{oc} P core = P oc is the constant core (no-load) iron loss in Watts.
P c u , F L = P s c P_{cu,FL} = P_{sc} P c u , F L = P sc is the full-load series copper loss ( I F L 2 R e q I_{FL}^2 R_{eq} I F L 2 R e q ) in Watts.
x 2 P c u , F L x^2 P_{cu,FL} x 2 P c u , F L is the copper loss at load fraction x x x .
Condition for Maximum Efficiency
Differentiating η \eta η with respect to load fraction x x x and setting d η / d x = 0 d\eta / dx = 0 d η / d x = 0 yields the fundamental maximum efficiency theorem: Variable Copper Loss ( x 2 P c u , F L ) = Constant Core Loss ( P c o r e ) \text{Variable Copper Loss } (x^2 P_{cu,FL}) = \text{Constant Core Loss } (P_{core}) Variable Copper Loss ( x 2 P c u , F L ) = Constant Core Loss ( P core ) x η , m a x = P c o r e P c u , F L x_{\eta,max} = \sqrt{\frac{P_{core}}{P_{cu,FL}}} x η , ma x = P c u , F L P core
The corresponding load apparent power at maximum efficiency is: S η , m a x = S r a t e d × P c o r e P c u , F L S_{\eta,max} = S_{rated} \times \sqrt{\frac{P_{core}}{P_{cu,FL}}} S η , ma x = S r a t e d × P c u , F L P core Efficiency Optimization Curve:
- Loss (W)
- ^
- | / Total Loss (Pcore + x^2*Pcu)
- | /
- | Pcu ====/==== x^2 * Pcu,FL
- | /
- |----------X-------------------- Pcore (constant)
- | /|
- | / |
- +-------+--+------------------------> Load Fraction x
- 0 x_max = sqrt(Pcore/Pcu,FL)
- 5. Transformer Testing, Diagnostics & Dissolved Gas Analysis (DGA)
- Routine Electrical Field Tests
Transformer Turns Ratio (TTR): Verifies the physical turns ratio across all tap positions within ± 0.5 % \pm 0.5\% ± 0.5% of nameplate per IEEE C57.12.90. Identifies shorted turns or open windings.
Winding DC Resistance Test: Utilizes a 4-wire Kelvin bridge or digital low-resistance ohmmeter (DLRO). Compares winding resistances across phases (must balance within ± 2 % \pm 2\% ± 2% ) to detect loose internal connections, tap changer contact degradation, or broken conductor strands.
Insulation Power Factor / Dissipation Factor ( tan δ \tan \delta tan δ ): Evaluates dielectric loss in winding insulation and bushings. New liquid-filled transformers must exhibit power factor < 0.5 % < 0.5\% < 0.5% at 20 ∘ C 20^\circ\text{C} 2 0 ∘ C . Values between 0.5 % 0.5\% 0.5% and 1.0 % 1.0\% 1.0% indicate insulation aging or moisture ingress; > 1.0 % > 1.0\% > 1.0% requires corrective processing.
Dissolved Gas Analysis (DGA per IEEE C57.104)
Mineral insulating oil breaks down thermally and electrically, releasing specific diagnostic hydrocarbon gases. DGA is the single most sensitive method for early internal fault detection.
Fault Gas Chemical Formula Primary Generation Mechanism & Internal Defect
Hydrogen H 2 \text{H}_2 H 2 Partial discharge (corona), low-energy electrical sparking, electrolysis from moisture
Methane CH 4 \text{CH}_4 CH 4 Low-temperature thermal oil breakdown ( < 300 ∘ C < 300^\circ\text{C} < 30 0 ∘ C )
Ethane C 2 H 6 \text{C}_2\text{H}_6 C 2 H 6 Medium-temperature thermal oil decomposition ( 300 ∘ C to 700 ∘ C 300^\circ\text{C} \text{ to } 700^\circ\text{C} 30 0 ∘ C to 70 0 ∘ C )
Ethylene C 2 H 4 \text{C}_2\text{H}_4 C 2 H 4 Severe high-temperature thermal overheating of oil ( > 700 ∘ C > 700^\circ\text{C} > 70 0 ∘ C , e.g., hot spots)
Acetylene C 2 H 2 \text{C}_2\text{H}_2 C 2 H 2 High-energy electric arcing , dielectric breakdown ( > 1000 ∘ C > 1000^\circ\text{C} > 100 0 ∘ C ) — Immediate Critical Hazard
Carbon Monoxide CO \text{CO} CO Thermal degradation and overheating of cellulose paper insulation
Carbon Dioxide CO 2 \text{CO}_2 CO 2 Severe cellulose insulation oxidation/aging (normal ratio CO 2 / CO ≈ 7 – 10 \text{CO}_2/\text{CO} \approx 7\text{--}10 CO 2 / CO ≈ 7 – 10 )
Exam Diagnostic Ratio Trap: The presence of trace Acetylene ( C 2 H 2 > 1 – 2 ppm \text{C}_2\text{H}_2 > 1\text{--}2\text{ ppm} C 2 H 2 > 1 – 2 ppm ) indicates active internal arcing and flashover. A CO 2 / CO \text{CO}_2/\text{CO} CO 2 / CO ratio dropping below 3.0 3.0 3.0 indicates dangerous cellulose paper insulation degradation.
- 6. Comprehensive Worked Transformer Calculation
- Problem Statement
A single-phase, 500 kVA 500\text{ kVA} 500 kVA , 13 , 800 V : 480 V 13,800\text{ V} : 480\text{ V} 13 , 800 V : 480 V , 60 Hz 60\text{ Hz} 60 Hz distribution transformer underwent open-circuit and short-circuit testing:
Open-Circuit Test (LV Side, HV Open): V o c = 480 V V_{oc} = 480\text{ V} V oc = 480 V , I o c = 18.5 A I_{oc} = 18.5\text{ A} I oc = 18.5 A , P o c = 2 , 200 W P_{oc} = 2,200\text{ W} P oc = 2 , 200 W .
Short-Circuit Test (HV Side, LV Shorted): V s c = 650 V V_{sc} = 650\text{ V} V sc = 650 V , I s c = 36.23 A I_{sc} = 36.23\text{ A} I sc = 36.23 A (rated HV current), P s c = 4 , 800 W P_{sc} = 4,800\text{ W} P sc = 4 , 800 W .
Calculate:
The equivalent series impedance parameters ( R e q , L V , X e q , L V R_{eq,LV}, X_{eq,LV} R e q , L V , X e q , L V ) and per-unit impedance Z p u Z_{pu} Z p u .
The full-load voltage regulation ( V R % VR\% V R % ) at 0.80 0.80 0.80 power factor lagging and 0.80 0.80 0.80 leading.
The full-load efficiency at 0.80 0.80 0.80 power factor lagging.
The kVA load at which maximum efficiency occurs and the maximum efficiency value at unity power factor.
Step-by-Step Solution
Step 1: Turns Ratio and Base Quantities a = 13 , 800 V 480 V = 28.75 a = \frac{13,800\text{ V}}{480\text{ V}} = 28.75 a = 480 V 13 , 800 V = 28.75 I r a t e d , L V = 500 , 000 VA 480 V = 1 , 041.67 A , I r a t e d , H V = 500 , 000 VA 13 , 800 V = 36.232 A I_{rated,LV} = \frac{500,000\text{ VA}}{480\text{ V}} = 1,041.67\text{ A}, \quad I_{rated,HV} = \frac{500,000\text{ VA}}{13,800\text{ V}} = 36.232\text{ A} I r a t e d , L V = 480 V 500 , 000 VA = 1 , 041.67 A , I r a t e d , H V = 13 , 800 V 500 , 000 VA = 36.232 A Z b a s e , L V = ( 480 V ) 2 500 , 000 VA = 0.4608 Ω Z_{base,LV} = \frac{(480\text{ V})^2}{500,000\text{ VA}} = 0.4608\ \Omega Z ba se , L V = 500 , 000 VA ( 480 V ) 2 = 0.4608 Ω
Step 2: Equivalent Series Impedance from Short-Circuit Test From the SC test on the HV side: R e q , H V = P s c I s c 2 = 4 , 800 W ( 36.232 A ) 2 = 3.6565 Ω R_{eq,HV} = \frac{P_{sc}}{I_{sc}^2} = \frac{4,800\text{ W}}{(36.232\text{ A})^2} = 3.6565\ \Omega R e q , H V = I sc 2 P sc = ( 36.232 A ) 2 4 , 800 W = 3.6565 Ω Z e q , H V = V s c I s c = 650 V 36.232 A = 17.940 Ω Z_{eq,HV} = \frac{V_{sc}}{I_{sc}} = \frac{650\text{ V}}{36.232\text{ A}} = 17.940\ \Omega Z e q , H V = I sc V sc = 36.232 A 650 V = 17.940 Ω X e q , H V = Z e q , H V 2 − R e q , H V 2 = ( 17.940 ) 2 − ( 3.6565 ) 2 = 17.563 Ω X_{eq,HV} = \sqrt{Z_{eq,HV}^2 - R_{eq,HV}^2} = \sqrt{(17.940)^2 - (3.6565)^2} = 17.563\ \Omega X e q , H V = Z e q , H V 2 − R e q , H V 2 = ( 17.940 ) 2 − ( 3.6565 ) 2 = 17.563 Ω
Referring parameters to the LV side: R e q , L V = R e q , H V a 2 = 3.6565 ( 28.75 ) 2 = 0.004423 Ω = 4.423 m Ω R_{eq,LV} = \frac{R_{eq,HV}}{a^2} = \frac{3.6565}{(28.75)^2} = 0.004423\ \Omega = 4.423\text{ m}\Omega R e q , L V = a 2 R e q , H V = ( 28.75 ) 2 3.6565 = 0.004423 Ω = 4.423 m Ω X e q , L V = X e q , H V a 2 = 17.563 ( 28.75 ) 2 = 0.021248 Ω = 21.248 m Ω X_{eq,LV} = \frac{X_{eq,HV}}{a^2} = \frac{17.563}{(28.75)^2} = 0.021248\ \Omega = 21.248\text{ m}\Omega X e q , L V = a 2 X e q , H V = ( 28.75 ) 2 17.563 = 0.021248 Ω = 21.248 m Ω Z e q , L V = 17.940 ( 28.75 ) 2 = 0.021704 Ω = 21.704 m Ω Z_{eq,LV} = \frac{17.940}{(28.75)^2} = 0.021704\ \Omega = 21.704\text{ m}\Omega Z e q , L V = ( 28.75 ) 2 17.940 = 0.021704 Ω = 21.704 m Ω
Per-Unit Series Impedances: R p u = R e q , L V Z b a s e , L V = 0.004423 Ω 0.4608 Ω = 0.00960 pu = 0.960 % R_{pu} = \frac{R_{eq,LV}}{Z_{base,LV}} = \frac{0.004423\ \Omega}{0.4608\ \Omega} = 0.00960\text{ pu} = 0.960\% R p u = Z ba se , L V R e q , L V = 0.4608 Ω 0.004423 Ω = 0.00960 pu = 0.960% X p u = X e q , L V Z b a s e , L V = 0.021248 Ω 0.4608 Ω = 0.04611 pu = 4.611 % X_{pu} = \frac{X_{eq,LV}}{Z_{base,LV}} = \frac{0.021248\ \Omega}{0.4608\ \Omega} = 0.04611\text{ pu} = 4.611\% X p u = Z ba se , L V X e q , L V = 0.4608 Ω 0.021248 Ω = 0.04611 pu = 4.611% Z p u = Z e q , L V Z b a s e , L V = 0.04710 pu = 4.710 % Z_{pu} = \frac{Z_{eq,LV}}{Z_{base,LV}} = 0.04710\text{ pu} = 4.710\% Z p u = Z ba se , L V Z e q , L V = 0.04710 pu = 4.710%
Step 3: Voltage Regulation Calculation
At 0.80 0.80 0.80 Lagging Power Factor ( cos θ = 0.80 \cos \theta = 0.80 cos θ = 0.80 , sin θ = + 0.60 \sin \theta = +0.60 sin θ = + 0.60 ): V R % ≈ [ R p u cos θ + X p u sin θ ] × 100 % VR\% \approx [R_{pu} \cos \theta + X_{pu} \sin \theta] \times 100\% V R % ≈ [ R p u cos θ + X p u sin θ ] × 100% V R % ≈ [ 0.00960 ( 0.80 ) + 0.04611 ( 0.60 ) ] × 100 % = [ 0.00768 + 0.02767 ] × 100 % = 3.535 % VR\% \approx [0.00960(0.80) + 0.04611(0.60)] \times 100\% = [0.00768 + 0.02767] \times 100\% = 3.535\% V R % ≈ [ 0.00960 ( 0.80 ) + 0.04611 ( 0.60 )] × 100% = [ 0.00768 + 0.02767 ] × 100% = 3.535%
Exact Calculation Check: V N L ′ = 480 ∠ 0 ∘ + ( 1041.67 ∠ − 36.87 ∘ ) ( 0.004423 + j 0.021248 ) = 480 + 22.608 ∠ 41.36 ∘ = 496.97 + j 14.94 = 497.19 ∠ 1.72 ∘ V \mathbf{V}_{NL}' = 480\angle 0^\circ + (1041.67\angle -36.87^\circ)(0.004423 + j0.021248) = 480 + 22.608\angle 41.36^\circ = 496.97 + j14.94 = 497.19\angle 1.72^\circ\text{ V} V N L ′ = 480∠ 0 ∘ + ( 1041.67∠ − 36.8 7 ∘ ) ( 0.004423 + j 0.021248 ) = 480 + 22.608∠41.3 6 ∘ = 496.97 + j 14.94 = 497.19∠1.7 2 ∘ V V R % e x a c t = 497.19 − 480 480 × 100 % = 3.58 % VR\%_{exact} = \frac{497.19 - 480}{480} \times 100\% = 3.58\% V R % e x a c t = 480 497.19 − 480 × 100% = 3.58%
At 0.80 0.80 0.80 Leading Power Factor ( cos θ = 0.80 \cos \theta = 0.80 cos θ = 0.80 , sin θ = − 0.60 \sin \theta = -0.60 sin θ = − 0.60 ): V R % ≈ [ R p u cos θ − X p u sin θ ] × 100 % VR\% \approx [R_{pu} \cos \theta - X_{pu} \sin \theta] \times 100\% V R % ≈ [ R p u cos θ − X p u sin θ ] × 100% V R % ≈ [ 0.00960 ( 0.80 ) − 0.04611 ( 0.60 ) ] × 100 % = [ 0.00768 − 0.02767 ] × 100 % = − 1.999 % ≈ − 2.00 % VR\% \approx [0.00960(0.80) - 0.04611(0.60)] \times 100\% = [0.00768 - 0.02767] \times 100\% = -1.999\% \approx -2.00\% V R % ≈ [ 0.00960 ( 0.80 ) − 0.04611 ( 0.60 )] × 100% = [ 0.00768 − 0.02767 ] × 100% = − 1.999% ≈ − 2.00%
Step 4: Full-Load Efficiency at 0.80 Lagging PF P o u t = 500 kVA × 0.80 = 400 kW P_{out} = 500\text{ kVA} \times 0.80 = 400\text{ kW} P o u t = 500 kVA × 0.80 = 400 kW P c o r e = 2 , 200 W = 2.20 kW , P c u , F L = 4 , 800 W = 4.80 kW P_{core} = 2,200\text{ W} = 2.20\text{ kW}, \quad P_{cu,FL} = 4,800\text{ W} = 4.80\text{ kW} P core = 2 , 200 W = 2.20 kW , P c u , F L = 4 , 800 W = 4.80 kW η F L = 400 kW 400 kW + 2.20 kW + 4.80 kW = 400 407.0 = 0.9828 = 98.28 % \eta_{FL} = \frac{400\text{ kW}}{400\text{ kW} + 2.20\text{ kW} + 4.80\text{ kW}} = \frac{400}{407.0} = 0.9828 = 98.28\% η F L = 400 kW + 2.20 kW + 4.80 kW 400 kW = 407.0 400 = 0.9828 = 98.28%
Step 5: Maximum Efficiency Load and Value x η , m a x = P c o r e P c u , F L = 2 , 200 W 4 , 800 W = 0.45833 = 0.6770 x_{\eta,max} = \sqrt{\frac{P_{core}}{P_{cu,FL}}} = \sqrt{\frac{2,200\text{ W}}{4,800\text{ W}}} = \sqrt{0.45833} = 0.6770 x η , ma x = P c u , F L P core = 4 , 800 W 2 , 200 W = 0.45833 = 0.6770 S η , m a x = 0.6770 × 500 kVA = 338.5 kVA S_{\eta,max} = 0.6770 \times 500\text{ kVA} = 338.5\text{ kVA} S η , ma x = 0.6770 × 500 kVA = 338.5 kVA
At unity power factor ( cos θ = 1.0 \cos \theta = 1.0 cos θ = 1.0 ): P o u t = 338.5 kW P_{out} = 338.5\text{ kW} P o u t = 338.5 kW P l o s s = P c o r e + x 2 P c u , F L = 2.20 kW + 2.20 kW = 4.40 kW P_{loss} = P_{core} + x^2 P_{cu,FL} = 2.20\text{ kW} + 2.20\text{ kW} = 4.40\text{ kW} P l oss = P core + x 2 P c u , F L = 2.20 kW + 2.20 kW = 4.40 kW η m a x = 338.5 kW 338.5 kW + 4.40 kW = 338.5 342.9 = 0.9872 = 98.72 % \eta_{max} = \frac{338.5\text{ kW}}{338.5\text{ kW} + 4.40\text{ kW}} = \frac{338.5}{342.9} = 0.9872 = 98.72\% η ma x = 338.5 kW + 4.40 kW 338.5 kW = 342.9 338.5 = 0.9872 = 98.72%
7. Common Exam Traps & Strategic Pitfalls
Test Referral Side Confusion: The Open-Circuit test gives parameters on the test winding side (usually LV); the Short-Circuit test gives series parameters on its test winding side (usually HV). Always verify which side the parameters are referred to before computing voltage drop.
Leading Power Factor Sign Error: Leading power factors subtract the reactive term in the voltage regulation formula ( R cos θ − X sin θ R \cos \theta - X \sin \theta R cos θ − X sin θ ), often producing negative regulation (voltage rise).
Copper Loss Scaling with Load Squared: P c u ( x ) = x 2 P c u , F L P_{cu}(x) = x^2 P_{cu,FL} P c u ( x ) = x 2 P c u , F L . At half load ( x = 0.5 x = 0.5 x = 0.5 ), copper losses drop to ( 0.5 ) 2 = 0.25 (0.5)^2 = 0.25 ( 0.5 ) 2 = 0.25 ( 25 % 25\% 25% ) of full load, NOT 50 % 50\% 50% .
Autotransformer High Fault Current Trap: Because the equivalent impedance of an autotransformer is reduced by ( 1 − 1 / a ) (1 - 1/a) ( 1 − 1/ a ) compared to a standard two-winding unit, short-circuit fault currents are dramatically higher.