Study guide
11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)
PE Electrical and Computer: Power Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Strategy & Reference Handbook
1.1 PE Power Exam Format, CBT Navigation & Reference Handbook 1.2 2026 Reference Standards (NEC 2020, NFPA 70E-2021, NESC) & Scoring Mechanics 1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery
2 Chapter 2: Measurement, Metering & Field Testing
2.1 Current Transformers (CTs), Potential Transformers (PTs) & Meter Connections 2.2 Instrument Transformer Burdens, Saturation Curves & Ratio Correction Factors 2.3 Insulation Resistance Testing (Megger, Polarization Index, Dielectric Absorption) 2.4 Ground Resistance Testing (Fall-of-Potential 62% Rule & Clamp-on Methods)
3 Chapter 3: General Applications — Grounding & Surge Protection
3.1 Substation Ground Grid Design & IEEE 80 Touch/Step Voltage Criteria 3.2 Lightning Protection Systems & Rolling Sphere / Cone of Protection Methods 3.3 Surge Protective Devices (SPDs) & Voltage Surge Arresters
4 Chapter 4: General Applications — Lighting & Energy Management
4.1 Illumination Engineering & Zonal Cavity / Lumen Method Calculations 4.2 Energy Management, Demand Factors & Load Factor Calculations 4.3 Economic Dispatch, Energy Efficiency & Load Profile Analysis
5 Chapter 5: Electrical Safety & NFPA Standards
5.1 NFPA 70E Shock Protection, Approach Boundaries & PPE Requirements 5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations 5.3 Hazardous (Classified) Locations (Class I, II, III & Division/Zone Systems) 5.4 Special Occupancies & Critical Systems (NEC Articles 517 Health Care, 700/701/702 Emergency)
6 Chapter 6: NEC Wiring Methods & Installation Requirements
6.1 Conductor Ampacity & NEC Table 310.16 Derating Adjustments 6.2 Raceway Fill, Box Sizing & Conduit Bending Calculations (Chapter 9 Tables) 6.3 Equipment Grounding Conductors & Grounding Electrode Sizing (NEC Article 250)
7 Chapter 7: Circuit Analysis — Fundamentals & Symmetrical Components
7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition) 7.2 Balanced Three-Phase Circuits (Wye-Delta Configurations & Power Formulas) 7.3 Symmetrical Components & Fortescue Sequence Transformation Matrices 7.4 Sequence Impedances & Positive, Negative, Zero Sequence Network Construction
8 Chapter 8: Circuit Analysis — Per-Unit & Phasor Analysis
8.1 Per-Unit System Fundamentals & Base Conversion Formulas 8.2 Three-Phase Per-Unit Network Modeling & Equipment Impedance Conversion 8.3 Phasor Diagrams, Complex Power & Power Triangle Relationships
9 Chapter 9: Power Electronics & Logic Controls
9.1 Power Electronic Converters (Rectifiers, Inverters & DC-DC Topologies) 9.2 Inverter-Based Resources (IBRs), Grid-Forming & Grid-Following Controls 9.3 Variable Frequency Drives (VFDs), PWM Operation & Harmonic Mitigation 9.4 Boolean Algebra, Logic Gates, De Morgan's Laws & Ladder Logic Control Diagrams
10 Chapter 10: Rotating Machines — Induction & Synchronous
10.1 Three-Phase Induction Motors (Equivalent Circuits, Slip & Performance) 10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes 10.3 Synchronous Machines (Operating Principles, Power-Angle Curves & V-Curves) 10.4 Motor Starting Methods (DOL, Wye-Delta, Autotransformer, Soft-Start) & Voltage Dip
11 Chapter 11: Electric Power Devices & Renewable Energy
11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation) 11.2 Power Factor Correction Capacitors & Shunt Bank Sizing 11.3 Battery Energy Storage Systems (BESS) & Ultracapacitors 11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)
12 Chapter 12: Transmission & Distribution — Steady-State & Power Quality
12.1 Transmission Line Modeling, Voltage Drop & Conductor Sizing 12.2 Voltage Regulation, Reactive Power Support & Tap-Changer Controls 12.3 Power Quality, Harmonics, THD & IEEE 519 Compliance 12.4 Power Flow Analysis & System Stability (Steady-State, Transient & Swing Equation)
13 Chapter 13: Transmission & Distribution — Fault Analysis & Transformer Shifts
13.1 Symmetrical Three-Phase Bolted Fault Calculations 13.2 Unsymmetrical Fault Analysis (SLG, L-L, DLG Fault Calculations) 13.3 Transformer Connection Types, Zero-Sequence Paths & 30-Degree Phase Shifts
14 Chapter 14: Protection Systems & Device Coordination
14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves 14.2 Protective Relaying Schemes (Differential 87, Distance 21, Undervoltage 27) 14.3 Circuit Breakers, Fuses & Automatic Reclosers 14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)
11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)
Key Takeaways Explain This Topic AI
Solar PV cell operation is defined by characteristic I-V and P-V curves; Maximum Power Point ( P m p = V m p ⋅ I m p P_{mp} = V_{mp} \cdot I_{mp} P m p = V m p ⋅ I m p ) defines the Fill Factor F F = P m p V o c ⋅ I s c ≈ 0.70 – 0.85 FF = \frac{P_{mp}}{V_{oc} \cdot I_{sc}} \approx 0.70\text{--}0.85 FF = V oc ⋅ I sc P m p ≈ 0.70 – 0.85 .
Open-circuit voltage increases as cell temperature drops ( β V o c ≈ − 0.28 to − 0.38 % / ∘ C \beta_{Voc} \approx -0.28\text{ to } -0.38\%/^\circ\text{C} β V oc ≈ − 0.28 to − 0.38% / ∘ C ); NEC 690.7 mandates calculating maximum PV string voltage at lowest expected ambient temperature ( V o c , m a x = V o c , S T C [ 1 + β V o c ( T m i n − 25 ∘ C ) ] V_{oc,max} = V_{oc,STC}[1 + \beta_{Voc}(T_{min} - 25^\circ\text{C})] V oc , ma x = V oc , STC [ 1 + β V oc ( T min − 2 5 ∘ C )] ).
Wind turbine aerodynamic power follows the cubic wind velocity law ( P w i n d = 1 2 ρ A v 3 P_{wind} = \frac{1}{2} \rho A v^3 P w in d = 2 1 ρ A v 3 ); the Betz limit establishes the theoretical maximum aerodynamic extraction efficiency at C p , m a x = 16 / 27 ≈ 59.26 % C_{p,max} = 16/27 \approx 59.26\% C p , ma x = 16/27 ≈ 59.26% .
Utility wind generators utilize four configurations: Type 1 (SCIG), Type 2 (variable rotor R), Type 3 (DFIG with partial ~30% converter), and Type 4 (Full-converter Synchronous / PMSG with complete grid isolation).
Inverter Maximum Power Point Tracking (MPPT) algorithms (Perturb & Observe, Incremental Conductance) dynamically maximize harvested power under changing irradiance and temperature.
Last updated: August 2026
11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)
Executive Overview: Renewable energy systems constitute a major domain on the NCEES PE Power examination. Candidates must master solar photovoltaic (PV) cell physics, standard test conditions (STC), I-V and P-V characteristic curves, cold-weather voltage correction per NEC 690.7, MPPT algorithms, wind turbine aerodynamic power equations ( P = 1 2 ρ A v 3 P = \frac{1}{2}\rho A v^3 P = 2 1 ρ A v 3 ), the Betz extraction limit ( 59.26 % 59.26\% 59.26% ), and the four standard wind turbine generator topologies (Types 1 through 4).
- 1. Solar Photovoltaic (PV) Device Physics & Characteristics
- The Photovoltaic Effect and Equivalent Circuit
A solar cell is a large-area semiconductor p-n junction diode that absorbs incident photons with energy greater than the semiconductor bandgap ( h ν > E g h\nu > E_g h ν > E g ), creating electron-hole pairs. Under an internal electric field, these carriers separate to produce a photocurrent ( I p h I_{ph} I p h ). Single-Diode PV Cell Model:
- +-------------[ Rs ]------------------------o (+) Terminal
- | Series Resistance |
- | |
- ( ^ ) Iph |\ /| |
- ( Solar ) | \ / | [
- ( Current ) -----\ /----- Diode [ ] Rsh (Shunt)
- ( v ) | \/ | [
- | | | |
- +--------------+--------+--------------------+--o (-) Terminal
The terminal current-voltage relationship is governed by the single-diode equation: I = I p h − I 0 [ exp ( q ( V + I R s ) n k T ) − 1 ] − V + I R s R s h I = I_{ph} - I_0 \left[ \exp\left( \frac{q (V + I R_s)}{n k T} \right) - 1 \right] - \frac{V + I R_s}{R_{sh}} I = I p h − I 0 [ exp ( nk T q ( V + I R s ) ) − 1 ] − R s h V + I R s
Where:
I p h I_{ph} I p h is light-generated photocurrent (proportional to solar irradiance G G G ).
I 0 I_0 I 0 is diode reverse saturation current.
q = 1.602 × 10 − 19 C q = 1.602 \times 10^{-19}\text{ C} q = 1.602 × 1 0 − 19 C (elementary electron charge).
k = 1.381 × 10 − 23 J/K k = 1.381 \times 10^{-23}\text{ J/K} k = 1.381 × 1 0 − 23 J/K (Boltzmann constant).
T T T is cell temperature in Kelvin ( K = ∘ C + 273.15 K = ^\circ\text{C} + 273.15 K = ∘ C + 273.15 ).
n n n is diode ideality factor ( 1.0 ≤ n ≤ 1.5 1.0 \le n \le 1.5 1.0 ≤ n ≤ 1.5 ).
R s R_s R s is series resistance (leads, grid fingers, contacts; ideal = 0 Ω 0\ \Omega 0 Ω ).
R s h R_{sh} R s h is shunt resistance (leakage across p-n junction; ideal = ∞ \infty ∞ ).
Standard Test Conditions (STC) & Key Parameters
Nameplate PV ratings are universally specified at Standard Test Conditions (STC):
- Irradiance ( G S T C G_{STC} G STC ): 1 , 000 W/m 2 1,000\text{ W/m}^2 1 , 000 W/m 2
- Cell Temperature ( T S T C T_{STC} T STC ): 25 ∘ C 25^\circ\text{C} 2 5 ∘ C
Air Mass Spectral Distribution ( A M AM A M ): 1.5 Global 1.5\text{ Global} 1.5 Global Characteristic I-V and P-V Curves:
- Current (A) Power (W)
- ^
- Isc|-------------------+ ^
- Pmp| | | P_mp (Max Power Point)
- | | | /\
- | \ | / \
- Imp| \-------+ (MPP: Vmp, Imp) | / \
- | | | / \
- | | | / \
- +----------------------------+----------+-----------> Voltage (V) +------+----------+-------> V
- 0 Vmp Voc 0 Vmp Voc
Key Metrics:
Open-Circuit Voltage ( V o c V_{oc} V oc ): Maximum voltage at zero current output.
Short-Circuit Current ( I s c I_{sc} I sc ): Maximum current at zero terminal voltage.
Maximum Power Point ( P m p P_{mp} P m p ): The operating point on the knee of the I-V curve where the product of voltage and current is maximized ( P m p = V m p × I m p P_{mp} = V_{mp} \times I_{mp} P m p = V m p × I m p ).
Fill Factor ( F F FF FF ): Measure of cell squareness and junction quality: F F = P m p V o c × I s c = V m p × I m p V o c × I s c FF = \frac{P_{mp}}{V_{oc} \times I_{sc}} = \frac{V_{mp} \times I_{mp}}{V_{oc} \times I_{sc}} FF = V oc × I sc P m p = V oc × I sc V m p × I m p High-efficiency commercial silicon modules exhibit F F ≈ 0.75 – 0.85 FF \approx 0.75\text{--}0.85 FF ≈ 0.75 – 0.85 .
- 2. Environmental Effects & NEC 690.7 Temperature Sizing
- Irradiance and Temperature Dependencies
Irradiance Impact: Photocurrent I p h I_{ph} I p h and short-circuit current I s c I_{sc} I sc scale directly linearly with solar irradiance ( I s c ∝ G I_{sc} \propto G I sc ∝ G ). Voltage increases only logarithmically with irradiance.
Temperature Impact: As cell temperature increases:
Bandgap narrows slightly, causing a minor increase in current ( α I s c ≈ + 0.04 to + 0.06 % / ∘ C \alpha_{Isc} \approx +0.04\text{ to } +0.06\%/^\circ\text{C} α I sc ≈ + 0.04 to + 0.06% / ∘ C ).
Diode reverse saturation current increases exponentially, causing a drastic drop in voltage ( β V o c ≈ − 0.28 to − 0.38 % / ∘ C \beta_{Voc} \approx -0.28\text{ to } -0.38\%/^\circ\text{C} β V oc ≈ − 0.28 to − 0.38% / ∘ C and β V m p ≈ − 0.35 to − 0.45 % / ∘ C \beta_{Vmp} \approx -0.35\text{ to } -0.45\%/^\circ\text{C} β Vm p ≈ − 0.35 to − 0.45% / ∘ C ).
Overall maximum power declines significantly ( γ P m p ≈ − 0.35 to − 0.45 % / ∘ C \gamma_{Pmp} \approx -0.35\text{ to } -0.45\%/^\circ\text{C} γ P m p ≈ − 0.35 to − 0.45% / ∘ C ).
Cold-Weather Maximum Voltage Calculation (NEC 690.7)
When ambient temperature drops, PV module open-circuit voltage rises. To prevent dielectric flashover and catastrophic inverter damage, NEC 690.7 mandates sizing string length based on the maximum open-circuit voltage calculated at the site's lowest historical design temperature ( T m i n T_{min} T min ): V o c , m a x = V o c , S T C × [ 1 + β V o c % × ( T m i n − 25 ∘ C ) ] V_{oc,max} = V_{oc,STC} \times \left[ 1 + \beta_{Voc\%} \times (T_{min} - 25^\circ\text{C}) \right] V oc , ma x = V oc , STC × [ 1 + β V oc % × ( T min − 2 5 ∘ C ) ] Or using absolute coefficient (V/ ∘ C ) : V o c , m a x = V o c , S T C + β V o c , a b s × ( T m i n − 25 ∘ C ) \text{Or using absolute coefficient (V/}^\circ\text{C}): \quad V_{oc,max} = V_{oc,STC} + \beta_{Voc,abs} \times (T_{min} - 25^\circ\text{C}) Or using absolute coefficient (V/ ∘ C ) : V oc , ma x = V oc , STC + β V oc , ab s × ( T min − 2 5 ∘ C )
Where β V o c % \beta_{Voc\%} β V oc % is the temperature coefficient expressed in % / ∘ C \%/^\circ\text{C} % / ∘ C (a negative quantity). Because ( T m i n − 25 ∘ C ) (T_{min} - 25^\circ\text{C}) ( T min − 2 5 ∘ C ) is negative for cold temperatures, the two negatives multiply to produce a net voltage increase ( V o c , m a x > V o c , S T C V_{oc,max} > V_{oc,STC} V oc , ma x > V oc , STC ). Maximum Modules per String: N m a x = ⌊ V d c , m a x , i n v e r t e r V o c , m a x ⌋ \text{Maximum Modules per String: } N_{max} = \left\lfloor \frac{V_{dc,max,inverter}}{V_{oc,max}} \right\rfloor Maximum Modules per String: N ma x = ⌊ V oc , ma x V d c , ma x , in v er t er ⌋
Hot-Weather Minimum MPPT Voltage Calculation
In extreme summer heat, cell operating temperature reaches T c e l l , m a x = T a m b , m a x + 30 ∘ C T_{cell,max} = T_{amb,max} + 30^\circ\text{C} T ce ll , ma x = T amb , ma x + 3 0 ∘ C (typically 65 ∘ C to 75 ∘ C 65^\circ\text{C} \text{ to } 75^\circ\text{C} 6 5 ∘ C to 7 5 ∘ C ). The minimum operating MPPT voltage is: V m p , m i n = V m p , S T C × [ 1 + β V m p % × ( T c e l l , m a x − 25 ∘ C ) ] V_{mp,min} = V_{mp,STC} \times \left[ 1 + \beta_{Vmp\%} \times (T_{cell,max} - 25^\circ\text{C}) \right] V m p , min = V m p , STC × [ 1 + β Vm p % × ( T ce ll , ma x − 2 5 ∘ C ) ] Minimum Modules per String: N m i n = ⌈ V m p p t , m i n , i n v e r t e r V m p , m i n ⌉ \text{Minimum Modules per String: } N_{min} = \left\lceil \frac{V_{mppt,min,inverter}}{V_{mp,min}} \right\rceil Minimum Modules per String: N min = ⌈ V m p , min V m ppt , min , in v er t er ⌉
- 3. Inverter Topologies & Maximum Power Point Tracking (MPPT)
- System Topologies
Central Inverters ( 1 – 4 MW 1\text{--}4\text{ MW} 1 – 4 MW ): Large utility installations; hundreds of parallel strings connected to a single central inverter. Lowest capital cost ( / W /W / W ), but susceptible to array-wide mismatch and partial shading losses.
String Inverters ( 50 – 250 kW 50\text{--}250\text{ kW} 50 – 250 kW ): Decentralized commercial/utility rooftop and ground-mount arrays; each inverter manages 6-12 strings with dedicated MPPT channels.
Module-Level Power Electronics (MLPE): Microinverters ( 300 – 500 W 300\text{--}500\text{ W} 300 – 500 W ) or DC Optimizers attached to individual modules; eliminates shading mismatch completely.
MPPT Control Algorithms
Perturb and Observe (P&O): Periodically perturbs operating voltage ( V + Δ V V + \Delta V V + Δ V ) and measures Δ P \Delta P Δ P . If Δ P > 0 \Delta P > 0 Δ P > 0 , voltage perturbation continues in the same direction; if Δ P < 0 \Delta P < 0 Δ P < 0 , direction is reversed. Exhibits minor steady-state oscillation around MPP.
Incremental Conductance (IncCond): Uses the mathematical derivative at the maximum power point ( d P / d V = 0 dP/dV = 0 d P / d V = 0 ): d P d V = d ( V ⋅ I ) d V = I + V d I d V = 0 ⟹ d I d V = − I V \frac{dP}{dV} = \frac{d(V \cdot I)}{dV} = I + V \frac{dI}{dV} = 0 \implies \frac{dI}{dV} = -\frac{I}{V} d V d P = d V d ( V ⋅ I ) = I + V d V d I = 0 ⟹ d V d I = − V I
At MPP: Δ I Δ V = − I V \frac{\Delta I}{\Delta V} = -\frac{I}{V} Δ V Δ I = − V I (Incremental Conductance = Opposite of Instantaneous Conductance).
Left of MPP: Δ I Δ V > − I V \frac{\Delta I}{\Delta V} > -\frac{I}{V} Δ V Δ I > − V I (Increase voltage).
Right of MPP: Δ I Δ V < − I V \frac{\Delta I}{\Delta V} < -\frac{I}{V} Δ V Δ I < − V I (Decrease voltage).
- 4. Wind Energy Fundamentals & Aerodynamic Power Extraction
- Power in the Wind Equation
The total kinetic energy per unit time passing through a circular swept area A A A normal to wind velocity v v v is: P w i n d = 1 2 m ˙ v 2 = 1 2 ( ρ A v ) v 2 = 1 2 ρ A v 3 P_{wind} = \frac{1}{2} \dot{m} v^2 = \frac{1}{2} (\rho A v) v^2 = \frac{1}{2} \rho A v^3 P w in d = 2 1 m ˙ v 2 = 2 1 ( ρ A v ) v 2 = 2 1 ρ A v 3
Where:
ρ \rho ρ is air density ( 1.225 kg/m 3 1.225\text{ kg/m}^3 1.225 kg/m 3 at standard temperature and sea level pressure).
A = π R 2 = π D 2 4 A = \pi R^2 = \frac{\pi D^2}{4} A = π R 2 = 4 π D 2 is the rotor swept area in m 2 \text{m}^2 m 2 ( R R R is blade length/radius, D D D is rotor diameter).
v v v is free-stream upstream wind velocity in m/s \text{m/s} m/s .
Cubic Power Rule: Aerodynamic wind power increases with the cube of wind speed ( P ∝ v 3 P \propto v^3 P ∝ v 3 ). Doubling wind speed increases available power by a factor of 2 3 = 8 2^3 = 8 2 3 = 8 ( 800 % 800\% 800% ).
The Betz Limit ( C p , m a x C_{p,max} C p , ma x )
A wind turbine cannot extract 100 % 100\% 100% of the wind kinetic energy, as the air would come to a complete standstill behind the rotor ( v 2 = 0 v_2 = 0 v 2 = 0 ), preventing upstream airflow. Applying momentum theory (actuator disk model), Albert Betz proved that maximum theoretical aerodynamic extraction efficiency is: C p , m a x = 16 27 ≈ 0.5926 = 59.26 % C_{p,max} = \frac{16}{27} \approx 0.5926 = 59.26\% C p , ma x = 27 16 ≈ 0.5926 = 59.26%
Actual mechanical turbine power extracted is: P m e c h = 1 2 ρ A v 3 C p ( λ , β ) P_{mech} = \frac{1}{2} \rho A v^3 C_p(\lambda, \beta) P m ec h = 2 1 ρ A v 3 C p ( λ , β )
Where C p C_p C p is the rotor power coefficient (typically 0.40 – 0.50 0.40\text{--}0.50 0.40 – 0.50 for modern three-bladed turbines), λ = ω R v \lambda = \frac{\omega R}{v} λ = v ω R is the Tip Speed Ratio (TSR), and β \beta β is blade pitch angle. Wind Turbine Operating Curve:
- Power (kW)
- ^
- | Rated Power Limit (Pitch Regulated)
- Pr | +==================================+
- | / |
- | / |
- | / |
- | / |
- | / |
- | / P ~ v^3 |
- | / |
- +---------------------------+------------------------------------------+-------> Wind Speed (m/s)
- 0 v_in (~3 m/s) v_out (~25 m/s)
- 5. Wind Turbine Generator Architectures (Types 1 through 4)
Utility wind turbines are classified into four distinct generator topologies defined by IEC standards: Type 1: Fixed Speed Squirrel-Cage Induction Generator (SCIG)
- [ Turbine / Gearbox ] ====> [ SCIG Stator ] ------------------------> Grid
- |
- +--- [ Shunt PFC Caps ]
- Type 2: Variable Slip Wound-Rotor Induction Generator (WRIG)
- [ Turbine / Gearbox ] ====> [ WRIG Stator ] ------------------------> Grid
- [ WRIG Rotor ] ---> [ Variable Resistor ]
- Type 3: Doubly-Fed Induction Generator (DFIG) - Partial Converter (~30% Rating)
- [ Turbine / Gearbox ] ====> [ DFIG Stator ] ------------------------> Grid
- [ DFIG Rotor ] <===> [ Back-to-Back Converter ] <===+
- Type 4: Full-Converter System (PMSG / WRSG) - 100% Inverter Decoupled
- [ Turbine Direct/Gear ] ===> [ Generator ] ===> [ 100% AC-DC-AC Converter ] ===> Grid
Topology Generator Type Grid Connection Speed Range Reactive Power Control Fault Ride-Through (LVRT)
Type 1 Squirrel-Cage Induction (SCIG) Direct stator connection Fixed ( < 1 % < 1\% < 1% slip) None (Consumes reactive power; needs shunt caps) Poor (Disconnection risk during grid faults)
Type 2 Wound-Rotor Induction (WRIG) Direct stator connection Narrow ( ≈ ± 10 % \approx \pm 10\% ≈ ± 10% ) Limited Poor
Type 3 (DFIG) Wound-Rotor Induction (DFIG) Stator direct; rotor via back-to-back converter Wide ( ≈ ± 30 % \approx \pm 30\% ≈ ± 30% ) Independent 4-quadrant P P P and Q Q Q control via rotor converter Moderate-Good (Requires rotor crowbar circuit)
Type 4 Synchronous (PMSG or WRSG) 100 % 100\% 100% via full AC-DC-AC converter Full ( 0 to 100 % 0\text{ to } 100\% 0 to 100% ) Complete independent P P P and Q Q Q decoupled grid control Superior (Full electronic compliance with IEEE 2800)
Exam Key Point: Type 3 (DFIG) uses a converter rated for only ≈ 30 % \approx 30\% ≈ 30% of machine capacity, saving cost while enabling sub-synchronous and super-synchronous operation. Type 4 routes 100 % 100\% 100% of power through the converter, fully isolating the generator from grid frequency dynamics and enabling direct-drive gearless operation.
- 6. Comprehensive Worked PV & Wind Calculation
- Problem Statement
Part A (PV Array Engineering): A commercial solar facility utilizes 450 W 450\text{ W} 450 W mono-crystalline PV modules connected to a 1 , 500 Vdc 1,500\text{ Vdc} 1 , 500 Vdc central inverter with an MPPT voltage window of 850 Vdc to 1 , 300 Vdc 850\text{ Vdc} \text{ to } 1,300\text{ Vdc} 850 Vdc to 1 , 300 Vdc .
Module STC Parameters: V o c , S T C = 49.2 V V_{oc,STC} = 49.2\text{ V} V oc , STC = 49.2 V , V m p , S T C = 41.5 V V_{mp,STC} = 41.5\text{ V} V m p , STC = 41.5 V , I s c , S T C = 11.60 A I_{sc,STC} = 11.60\text{ A} I sc , STC = 11.60 A , I m p , S T C = 10.84 A I_{mp,STC} = 10.84\text{ A} I m p , STC = 10.84 A .
Temperature Coefficients: β V o c = − 0.29 % / ∘ C \beta_{Voc} = -0.29\%/^\circ\text{C} β V oc = − 0.29% / ∘ C , β V m p = − 0.35 % / ∘ C \beta_{Vmp} = -0.35\%/^\circ\text{C} β Vm p = − 0.35% / ∘ C .
Site Climate Data: Lowest expected ambient design temperature T m i n = − 20 ∘ C T_{min} = -20^\circ\text{C} T min = − 2 0 ∘ C ; Maximum summer ambient temperature T a m b , m a x = 40 ∘ C T_{amb,max} = 40^\circ\text{C} T amb , ma x = 4 0 ∘ C (maximum operating cell temperature T c e l l , m a x = 70 ∘ C T_{cell,max} = 70^\circ\text{C} T ce ll , ma x = 7 0 ∘ C ).
Calculate:
The module Fill Factor ( F F FF FF ) at STC.
The maximum open-circuit voltage per module at − 20 ∘ C -20^\circ\text{C} − 2 0 ∘ C and the maximum permissible number of modules per series string ( N m a x N_{max} N ma x ) per NEC 690.7.
The minimum MPPT operating voltage per module at 70 ∘ C 70^\circ\text{C} 7 0 ∘ C and the minimum number of modules per string ( N m i n N_{min} N min ) to stay within the inverter MPPT window.
Part B (Wind Turbine Power Calculation): A utility-scale wind turbine has a rotor diameter of D = 112 m D = 112\text{ m} D = 112 m . At a site where air density is ρ = 1.20 kg/m 3 \rho = 1.20\text{ kg/m}^3 ρ = 1.20 kg/m 3 , the steady wind speed is v = 9.5 m/s v = 9.5\text{ m/s} v = 9.5 m/s . The turbine operates at a power coefficient of C p = 0.44 C_p = 0.44 C p = 0.44 , with a drivetrain mechanical-to-electrical conversion efficiency of η = 92.0 % \eta = 92.0\% η = 92.0% .
Calculate: 4. The total wind power incident on the rotor swept area and the net electrical power delivered to the grid.
Step-by-Step Solution
Step 1: Module Fill Factor ( F F FF FF ) P m p = 450 W P_{mp} = 450\text{ W} P m p = 450 W F F = P m p V o c , S T C × I s c , S T C = 450 W 49.2 V × 11.60 A = 450 W 570.72 VA = 0.7885 = 78.85 % FF = \frac{P_{mp}}{V_{oc,STC} \times I_{sc,STC}} = \frac{450\text{ W}}{49.2\text{ V} \times 11.60\text{ A}} = \frac{450\text{ W}}{570.72\text{ VA}} = 0.7885 = 78.85\% FF = V oc , STC × I sc , STC P m p = 49.2 V × 11.60 A 450 W = 570.72 VA 450 W = 0.7885 = 78.85%
Step 2: Maximum Cold-Weather Voltage and String Sizing (NEC 690.7) Δ T c o l d = T m i n − 25 ∘ C = − 20 ∘ C − 25 ∘ C = − 45 ∘ C \Delta T_{cold} = T_{min} - 25^\circ\text{C} = -20^\circ\text{C} - 25^\circ\text{C} = -45^\circ\text{C} Δ T co l d = T min − 2 5 ∘ C = − 2 0 ∘ C − 2 5 ∘ C = − 4 5 ∘ C Voltage Multiplier = 1 + [ ( − 0.0029 / ∘ C ) × ( − 45 ∘ C ) ] = 1 + 0.1305 = 1.1305 \text{Voltage Multiplier} = 1 + [(-0.0029/^\circ\text{C}) \times (-45^\circ\text{C})] = 1 + 0.1305 = 1.1305 Voltage Multiplier = 1 + [( − 0.0029 / ∘ C ) × ( − 4 5 ∘ C )] = 1 + 0.1305 = 1.1305 V o c , m a x = 49.2 V × 1.1305 = 55.62 V V_{oc,max} = 49.2\text{ V} \times 1.1305 = 55.62\text{ V} V oc , ma x = 49.2 V × 1.1305 = 55.62 V N m a x = ⌊ V d c , m a x , i n v e r t e r V o c , m a x ⌋ = ⌊ 1 , 500 V 55.62 V ⌋ = ⌊ 26.97 ⌋ = 26 modules per string N_{max} = \left\lfloor \frac{V_{dc,max,inverter}}{V_{oc,max}} \right\rfloor = \left\lfloor \frac{1,500\text{ V}}{55.62\text{ V}} \right\rfloor = \lfloor 26.97 \rfloor = \mathbf{26\text{ modules per string}} N ma x = ⌊ V oc , ma x V d c , ma x , in v er t er ⌋ = ⌊ 55.62 V 1 , 500 V ⌋ = ⌊ 26.97 ⌋ = 26 modules per string
Step 3: Minimum Summer MPPT Voltage and String Sizing Δ T h o t = T c e l l , m a x − 25 ∘ C = 70 ∘ C − 25 ∘ C = + 45 ∘ C \Delta T_{hot} = T_{cell,max} - 25^\circ\text{C} = 70^\circ\text{C} - 25^\circ\text{C} = +45^\circ\text{C} Δ T h o t = T ce ll , ma x − 2 5 ∘ C = 7 0 ∘ C − 2 5 ∘ C = + 4 5 ∘ C Voltage Multiplier = 1 + [ ( − 0.0035 / ∘ C ) × ( + 45 ∘ C ) ] = 1 − 0.1575 = 0.8425 \text{Voltage Multiplier} = 1 + [(-0.0035/^\circ\text{C}) \times (+45^\circ\text{C})] = 1 - 0.1575 = 0.8425 Voltage Multiplier = 1 + [( − 0.0035 / ∘ C ) × ( + 4 5 ∘ C )] = 1 − 0.1575 = 0.8425 V m p , m i n = 41.5 V × 0.8425 = 34.96 V V_{mp,min} = 41.5\text{ V} \times 0.8425 = 34.96\text{ V} V m p , min = 41.5 V × 0.8425 = 34.96 V N m i n = ⌈ V m p p t , m i n , i n v e r t e r V m p , m i n ⌉ = ⌈ 850 V 34.96 V ⌉ = ⌈ 24.31 ⌉ = 25 modules per string N_{min} = \left\lceil \frac{V_{mppt,min,inverter}}{V_{mp,min}} \right\rceil = \left\lceil \frac{850\text{ V}}{34.96\text{ V}} \right\rceil = \lceil 24.31 \rceil = \mathbf{25\text{ modules per string}} N min = ⌈ V m p , min V m ppt , min , in v er t er ⌉ = ⌈ 34.96 V 850 V ⌉ = ⌈ 24.31 ⌉ = 25 modules per string
String Design Window: Allowable string size is 25 to 26 modules 25\text{ to } 26\text{ modules} 25 to 26 modules (optimal choice is 26 modules/string , which produces 26 × 34.96 V = 909 V > 850 V 26 \times 34.96\text{ V} = 909\text{ V} > 850\text{ V} 26 × 34.96 V = 909 V > 850 V at max heat and 26 × 55.62 V = 1 , 446 V < 1 , 500 V 26 \times 55.62\text{ V} = 1,446\text{ V} < 1,500\text{ V} 26 × 55.62 V = 1 , 446 V < 1 , 500 V in extreme cold).
Step 4: Wind Turbine Aerodynamic & Electrical Power
Swept Area: R = D 2 = 112 m 2 = 56 m R = \frac{D}{2} = \frac{112\text{ m}}{2} = 56\text{ m} R = 2 D = 2 112 m = 56 m A = π R 2 = π ( 56 m ) 2 = 9 , 852.03 m 2 A = \pi R^2 = \pi (56\text{ m})^2 = 9,852.03\text{ m}^2 A = π R 2 = π ( 56 m ) 2 = 9 , 852.03 m 2
Total Kinetic Wind Power: P w i n d = 1 2 ρ A v 3 = 1 2 ( 1.20 kg/m 3 ) ( 9 , 852.03 m 2 ) ( 9.5 m/s ) 3 P_{wind} = \frac{1}{2} \rho A v^3 = \frac{1}{2} (1.20\text{ kg/m}^3)(9,852.03\text{ m}^2)(9.5\text{ m/s})^3 P w in d = 2 1 ρ A v 3 = 2 1 ( 1.20 kg/m 3 ) ( 9 , 852.03 m 2 ) ( 9.5 m/s ) 3 P w i n d = 0.60 × 9 , 852.03 × 857.375 = 5 , 068 , 141 W = 5 , 068.1 kW = 5.068 MW P_{wind} = 0.60 \times 9,852.03 \times 857.375 = 5,068,141\text{ W} = 5,068.1\text{ kW} = 5.068\text{ MW} P w in d = 0.60 × 9 , 852.03 × 857.375 = 5 , 068 , 141 W = 5 , 068.1 kW = 5.068 MW
Mechanical Aerodynamic Power Extracted by Rotor ( C p = 0.44 C_p = 0.44 C p = 0.44 ): P m e c h = P w i n d × C p = 5 , 068.1 kW × 0.44 = 2 , 229.98 kW = 2.230 MW P_{mech} = P_{wind} \times C_p = 5,068.1\text{ kW} \times 0.44 = 2,229.98\text{ kW} = 2.230\text{ MW} P m ec h = P w in d × C p = 5 , 068.1 kW × 0.44 = 2 , 229.98 kW = 2.230 MW
Electrical Power Output Delivered to Grid ( η = 92.0 % \eta = 92.0\% η = 92.0% ): P e l e c = P m e c h × η = 2 , 229.98 kW × 0.920 = 2 , 051.58 kW = 2.052 MW P_{elec} = P_{mech} \times \eta = 2,229.98\text{ kW} \times 0.920 = 2,051.58\text{ kW} = \mathbf{2.052\text{ MW}} P e l ec = P m ec h × η = 2 , 229.98 kW × 0.920 = 2 , 051.58 kW = 2.052 MW
7. Common Exam Traps & Strategic Pitfalls
Cold Weather Sign Inversion: Open-circuit voltage rises when temperature drops. Forgetting that β V o c \beta_{Voc} β V oc is negative and subtracting the temperature delta instead of adding will result in an undersized, dangerous string calculation that violates NEC 690.7.
Wind Speed Velocity Exponent Trap: Wind power is proportional to v 3 v^3 v 3 , NOT v 2 v^2 v 2 . A 20 % 20\% 20% increase in wind speed ( 1.20 × v 1.20 \times v 1.20 × v ) yields a ( 1.20 ) 3 = 1.728 (1.20)^3 = 1.728 ( 1.20 ) 3 = 1.728 ( 72.8 % 72.8\% 72.8% ) increase in generated electrical power.
DFIG Converter Rating vs. Machine Rating: The power electronics converter in a Type 3 DFIG is rated for only ≈ 30 % \approx 30\% ≈ 30% of the total generator rating, whereas Type 4 converters must be rated for 100 % 100\% 100% full output capacity.