Study guide
5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations
PE Electrical and Computer: Power Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Strategy & Reference Handbook
1.1 PE Power Exam Format, CBT Navigation & Reference Handbook 1.2 2026 Reference Standards (NEC 2020, NFPA 70E-2021, NESC) & Scoring Mechanics 1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery
2 Chapter 2: Measurement, Metering & Field Testing
2.1 Current Transformers (CTs), Potential Transformers (PTs) & Meter Connections 2.2 Instrument Transformer Burdens, Saturation Curves & Ratio Correction Factors 2.3 Insulation Resistance Testing (Megger, Polarization Index, Dielectric Absorption) 2.4 Ground Resistance Testing (Fall-of-Potential 62% Rule & Clamp-on Methods)
3 Chapter 3: General Applications — Grounding & Surge Protection
3.1 Substation Ground Grid Design & IEEE 80 Touch/Step Voltage Criteria 3.2 Lightning Protection Systems & Rolling Sphere / Cone of Protection Methods 3.3 Surge Protective Devices (SPDs) & Voltage Surge Arresters
4 Chapter 4: General Applications — Lighting & Energy Management
4.1 Illumination Engineering & Zonal Cavity / Lumen Method Calculations 4.2 Energy Management, Demand Factors & Load Factor Calculations 4.3 Economic Dispatch, Energy Efficiency & Load Profile Analysis
5 Chapter 5: Electrical Safety & NFPA Standards
5.1 NFPA 70E Shock Protection, Approach Boundaries & PPE Requirements 5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations 5.3 Hazardous (Classified) Locations (Class I, II, III & Division/Zone Systems) 5.4 Special Occupancies & Critical Systems (NEC Articles 517 Health Care, 700/701/702 Emergency)
6 Chapter 6: NEC Wiring Methods & Installation Requirements
6.1 Conductor Ampacity & NEC Table 310.16 Derating Adjustments 6.2 Raceway Fill, Box Sizing & Conduit Bending Calculations (Chapter 9 Tables) 6.3 Equipment Grounding Conductors & Grounding Electrode Sizing (NEC Article 250)
7 Chapter 7: Circuit Analysis — Fundamentals & Symmetrical Components
7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition) 7.2 Balanced Three-Phase Circuits (Wye-Delta Configurations & Power Formulas) 7.3 Symmetrical Components & Fortescue Sequence Transformation Matrices 7.4 Sequence Impedances & Positive, Negative, Zero Sequence Network Construction
8 Chapter 8: Circuit Analysis — Per-Unit & Phasor Analysis
8.1 Per-Unit System Fundamentals & Base Conversion Formulas 8.2 Three-Phase Per-Unit Network Modeling & Equipment Impedance Conversion 8.3 Phasor Diagrams, Complex Power & Power Triangle Relationships
9 Chapter 9: Power Electronics & Logic Controls
9.1 Power Electronic Converters (Rectifiers, Inverters & DC-DC Topologies) 9.2 Inverter-Based Resources (IBRs), Grid-Forming & Grid-Following Controls 9.3 Variable Frequency Drives (VFDs), PWM Operation & Harmonic Mitigation 9.4 Boolean Algebra, Logic Gates, De Morgan's Laws & Ladder Logic Control Diagrams
10 Chapter 10: Rotating Machines — Induction & Synchronous
10.1 Three-Phase Induction Motors (Equivalent Circuits, Slip & Performance) 10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes 10.3 Synchronous Machines (Operating Principles, Power-Angle Curves & V-Curves) 10.4 Motor Starting Methods (DOL, Wye-Delta, Autotransformer, Soft-Start) & Voltage Dip
11 Chapter 11: Electric Power Devices & Renewable Energy
11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation) 11.2 Power Factor Correction Capacitors & Shunt Bank Sizing 11.3 Battery Energy Storage Systems (BESS) & Ultracapacitors 11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)
12 Chapter 12: Transmission & Distribution — Steady-State & Power Quality
12.1 Transmission Line Modeling, Voltage Drop & Conductor Sizing 12.2 Voltage Regulation, Reactive Power Support & Tap-Changer Controls 12.3 Power Quality, Harmonics, THD & IEEE 519 Compliance 12.4 Power Flow Analysis & System Stability (Steady-State, Transient & Swing Equation)
13 Chapter 13: Transmission & Distribution — Fault Analysis & Transformer Shifts
13.1 Symmetrical Three-Phase Bolted Fault Calculations 13.2 Unsymmetrical Fault Analysis (SLG, L-L, DLG Fault Calculations) 13.3 Transformer Connection Types, Zero-Sequence Paths & 30-Degree Phase Shifts
14 Chapter 14: Protection Systems & Device Coordination
14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves 14.2 Protective Relaying Schemes (Differential 87, Distance 21, Undervoltage 27) 14.3 Circuit Breakers, Fuses & Automatic Reclosers 14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)
5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations
Key Takeaways Explain This Topic AI
An electric arc produces extreme thermal plasma temperatures exceeding 35,000°F (19,400°C) and volumetric copper expansion of approximately 67,000:1 from solid to vapor, generating destructive overpressure blast waves.
The Arc-Flash Boundary (AFB) is defined as the distance at which incident energy equals 1.2 cal/cm² (5.0 J/cm²), which corresponds to the onset of a second-degree (curable) burn on unprotected skin.
IEEE 1584-2018 models incident energy across five electrode configurations (VCB, VCBB, HCB, VOA, HOA), with horizontal configurations (HCB) directing the arc plasma jet straight toward the worker.
Clearing time determination must evaluate both 100% of the calculated arcing current (I_arc) and 85% of I_arc on the upstream protective device TCC curve to account for potential slower clearing times.
NFPA 70E PPE Category tables and incident energy calculations are mutually exclusive methods that cannot be mixed on the same electrical equipment.
Last updated: August 2026
5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations
Executive Overview: Arc-flash hazards represent one of the most violent thermal and explosive phenomena encountered in electrical power systems. The NCEES PE Power examination evaluates candidates on arc-flash physics, calculating the Arc-Flash Boundary (AFB), understanding the parameters governing IEEE 1584-2018 incident energy calculations, and correctly interpreting Time-Current Characteristic (TCC) curves—including the critical 85% arcing current reduction check. Understanding how electrode geometry, clearing time, and working distance influence incident energy is vital for safety compliance and exam mastery.
1. Physics & Dynamics of an Arc-Flash Event
An arc flash is an electric current that flows through ionized air (plasma) between energized conductors or between an energized conductor and ground. It is initiated by insulation breakdown, accidental tool bridging, rodent contamination, or mechanical failure.
Key Physical Phenomena of Arcing Faults
Extreme Temperatures: The core temperature of an electrical arc terminal can reach 35 , 000 ∘ F ( 19 , 400 ∘ C ) 35,000^\circ\text{F} (19,400^\circ\text{C}) 35 , 00 0 ∘ F ( 19 , 40 0 ∘ C ) , roughly four times the surface temperature of the sun. At these temperatures, radiant heat transfers instantaneously to surrounding materials.
Vaporization & Massive Volumetric Expansion: Solid copper vaporizes into gas almost instantaneously. Copper experiences a 67 , 000 × 67,000\times 67 , 000 × volume expansion during its transition from solid metal to vapor at atmospheric pressure. This explosive expansion generates intense blast overpressures exceeding 2 , 000 lbs/ft 2 2,000\text{ lbs/ft}^2 2 , 000 lbs/ft 2 , rupturing switchgear cubicles, dislodging doors, and propelling molten metal droplets and shrapnel at speeds exceeding 700 mph 700\text{ mph} 700 mph .
Radiant Energy Emissions: The arc emits massive flux across the electromagnetic spectrum, including intense ultraviolet (UV) radiation (causing photokeratitis / "arc eye") and infrared (IR) radiation (causing deep third-degree thermal burns).
Toxic Metal Fumes: Inhalation of vaporized copper, lead, and ozone causes acute chemical pneumonitis and severe respiratory damage.
- 2. Arc-Flash Boundary (AFB) & Physiological Burn Thresholds
- The 1.2 cal/cm 2 1.2\text{ cal/cm}^2 1.2 cal/cm 2 Criterion
The Arc-Flash Boundary (AFB) is defined by NFPA 70E and IEEE 1584 as the distance from an exposed energized arc source at which the incident energy equals 1.2 cal/cm 2 1.2\text{ cal/cm}^2 1.2 cal/cm 2 ( 5.0 J/cm 2 5.0\text{ J/cm}^2 5.0 J/cm 2 ) for a specified clearing time. +-------------------------------------------------------------------------+
- | PHYSIOLOGICAL SIGNIFICANCE OF 1.2 cal/cm² |
- | |
- | • Defined by the Alice Stoll Curve (Stoll & Greene thermal model) |
- | • 1.2 cal/cm² applied over 1.0 second equals the threshold of onset |
- | of a second-degree (blistering, but curable) burn on human skin. |
- | • Any person crossing inside the AFB MUST wear appropriate Arc-Rated |
- | (AR) clothing and PPE. |
- +-------------------------------------------------------------------------+ [ Arc Source ]
- |
- <----------------------> | Working Distance (D)
- (Incident Energy E) | (e.g., 18" for LV Switchgear)
- |
- <---------------------------------------------> Arc-Flash Boundary (AFB)
- (Energy = 1.2 cal/cm² threshold) | (PPE Required Inside)
- 3. IEEE 1584-2018 Calculation Methodology
IEEE 1584-2018 ( IEEE Guide for Performing Arc-Flash Hazard Calculations ) provides the empirical and physics-based analytical framework for determining arcing current, incident energy, and arc-flash boundaries.
Scope and Range of Validity
System Voltages: Three-phase AC from 208 V 208\text{ V} 208 V to 15 , 000 V 15,000\text{ V} 15 , 000 V ( 50 Hz 50\text{ Hz} 50 Hz or 60 Hz 60\text{ Hz} 60 Hz ).
Bolted Fault Current Range ( I b f I_{bf} I b f ):
208 V − 600 V 208\text{ V} - 600\text{ V} 208 V − 600 V : 0.5 kA 0.5\text{ kA} 0.5 kA to 106 kA 106\text{ kA} 106 kA
601 V − 15 , 000 V 601\text{ V} - 15,000\text{ V} 601 V − 15 , 000 V : 0.2 kA 0.2\text{ kA} 0.2 kA to 65 kA 65\text{ kA} 65 kA
Electrode Gap ( G G G ): 6.35 mm − 76.2 mm 6.35\text{ mm} - 76.2\text{ mm} 6.35 mm − 76.2 mm for LV; up to 254 mm 254\text{ mm} 254 mm for MV.
Bolted Fault Current ( I b f I_{bf} I b f ) vs. Arcing Current ( I a r c I_{arc} I a rc )
Because an electric arc introduces dynamic plasma resistance into the circuit, the arcing current ( I a r c I_{arc} I a rc ) is always strictly less than the available symmetrical bolted fault current ( I b f I_{bf} I b f ): I a r c < I b f I_{arc} < I_{bf} I a rc < I b f
At 480 V 480\text{ V} 480 V , I a r c I_{arc} I a rc is typically between 40 % 40\% 40% and 60 % 60\% 60% of I b f I_{bf} I b f . At medium voltages ( > 1 kV >1\text{ kV} > 1 kV ), the arc resistance represents a smaller fraction of the system impedance, so I a r c I_{arc} I a rc is typically 80 % 80\% 80% to 95 % 95\% 95% of I b f I_{bf} I b f .
The Five IEEE 1584-2018 Electrode Configurations
IEEE 1584-2018 introduced five distinct electrode configurations to model how enclosure geometry and bus orientation focus the arc blast:
Configuration Full Name Orientation & Enclosure Description Arc Behavior & Thermal Intensity
VCB Vertical Conductors in Box Vertical electrodes inside a metal enclosure. Arc travels downward toward the ends; plasma reflects off the box bottom and emerges outward. Moderate-high incident energy.
VCBB Vertical Conductors with Barrier in Box Vertical electrodes terminated in an insulating barrier inside a box. Barrier prevents arc from traveling off electrode ends; forces arc directly outward toward the enclosure opening. High incident energy.
HCB Horizontal Conductors in Box Electrodes oriented horizontally, pointing directly out the open front of the box. Arc plasma jet is directed straight at the worker . Produces the highest incident energy of all configurations!
VOA Vertical Conductors in Open Air Electrodes oriented vertically in open air (e.g., outdoor substation). Spherical free-air expansion; plasma disperses in all directions. Lower incident energy than enclosed configurations.
HOA Horizontal Conductors in Open Air Electrodes oriented horizontally in open air. Directional jet directed horizontally without enclosure reflection. VCB (Vertical in Box) VCBB (Vertical Barrier) HCB (Horizontal in Box)
- +------------------+ +------------------+ +------------------+
- | | | | | | | | | | | |
- | v v v | | v v v | | ======> |
- | Arc downward | | ============== | | ======> Worker |
- | plasma bounces | | (Insul Barrier) | | ======> Plasma |
- +---------\/-------+ +---------\/-------+ +------------------+
- -> Out ==> High ===> MAX
- Working Distance ( D D D )
The working distance is the assumed distance between the potential arc point and the worker's face and chest:
Low-Voltage Panelboards & Control Panels: D = 18 in ( 457 mm ) D = 18\text{ in } (457\text{ mm}) D = 18 in ( 457 mm )
Low-Voltage Switchboards & MCCs: D = 18 in − 24 in ( 457 mm − 610 mm ) D = 18\text{ in } - 24\text{ in } (457\text{ mm} - 610\text{ mm}) D = 18 in − 24 in ( 457 mm − 610 mm )
Medium-Voltage Switchgear & Breaker Cubicles: D = 36 in ( 914 mm ) D = 36\text{ in } (914\text{ mm}) D = 36 in ( 914 mm )
The Proportionality Governing Incident Energy
Incident energy ( E E E ) in cal/cm 2 \text{cal/cm}^2 cal/cm 2 scales according to the fundamental relationship: E ∝ I a r c k ⋅ t D x E \propto \frac{I_{arc}^k \cdot t}{D^x} E ∝ D x I a rc k ⋅ t
Where:
t t t = arcing duration (clearing time of the upstream protective device in seconds)
D D D = working distance (energy decays approximately with the inverse square D 2 D^2 D 2 , modified by enclosure reflection)
- k , x k, x k , x = empirical curve-fitting exponents from IEEE 1584
- The 85% Arcing Current Sensitivity Check
Because overcurrent protective devices (OCPDs) have inverse-time characteristics, a lower current may result in a significantly longer clearing time ( t t t ): +-------------------------------------------------------------------------+
- | THE 85% ARCING CURRENT RULE (IEEE 1584) |
- | |
- | 1. Calculate Incident Energy (E_1) using 100% of calculated I_arc. |
- | 2. Calculate Incident Energy (E_2) using 85% of calculated I_arc |
- | (I_arc_red = 0.85 * I_arc) to account for arc variation. |
- | 3. Find clearing time t_2 from the TCC curve at 0.85 * I_arc. |
- | 4. The Governing Incident Energy E = MAX(E_1, E_2). |
- +-------------------------------------------------------------------------+
Exam Trap — The Low Current Paradox: Examinees often assume the maximum bolted fault current produces the worst-case incident energy. If 0.85 ⋅ I a r c 0.85 \cdot I_{arc} 0.85 ⋅ I a rc shifts the operating point from the instantaneous trip region ( 0.03 s 0.03\text{ s} 0.03 s ) into the short-time or long-time delay region ( 0.5 s 0.5\text{ s} 0.5 s ), the clearing time jumps by a factor of 15, resulting in a dramatically higher incident energy despite the lower current!
4. NFPA 70E PPE Selection Methods & Equipment Labeling
NFPA 70E provides two distinct, mutually exclusive methods for selecting arc-rated PPE (Article 130.5 and Article 130.7):
Method 1: Incident Energy Analysis Method (Article 130.5)
Incident energy is calculated at the working distance using IEEE 1584 formulas.
PPE is selected with an Arc Thermal Performance Value (ATPV) or Breakopen Threshold Energy ( E B T E_{BT} E BT ) equal to or greater than the calculated incident energy ( E A R ≥ E c a l c E_{AR} \ge E_{calc} E A R ≥ E c a l c ).
Method 2: PPE Category Method (Table 130.7(C)(15)(a) & (b))
Used when detailed incident energy calculations have not been performed.
Applicable ONLY if the actual power system parameters (maximum available fault current, maximum fault clearing time, and minimum working distance) are strictly within the specific boundary limits listed in the NFPA 70E tables.
PPE Category Minimum Arc Rating Required Protective Garments & Equipment
Category 1 4 cal/cm 2 4\text{ cal/cm}^2 4 cal/cm 2 Arc-rated long-sleeve shirt and pants (or AR coverall), AR face shield with balaclava or AR flash hood, heavy-duty leather gloves.
Category 2 8 cal/cm 2 8\text{ cal/cm}^2 8 cal/cm 2 Arc-rated long-sleeve shirt and pants (or AR coverall), AR face shield with balaclava or AR flash hood, heavy-duty leather gloves.
Category 3 25 cal/cm 2 25\text{ cal/cm}^2 25 cal/cm 2 Arc-rated flash suit jacket and pants (or AR flash suit), AR flash suit hood, arc-rated gloves or leather over rubber insulating gloves.
Category 4 40 cal/cm 2 40\text{ cal/cm}^2 40 cal/cm 2 Arc-rated flash suit jacket and pants (or AR flash suit), AR flash suit hood (minimum 40 cal/cm 2 40\text{ cal/cm}^2 40 cal/cm 2 ), arc-rated gloves.
> 40 cal/cm 2 > 40\text{ cal/cm}^2 > 40 cal/cm 2 Extreme Danger NO ENERGIZED WORK PERMITTED. Incident energy exceeds blast survivability threshold; equipment must be de-energized or operated remotely.
Mandatory Rule — Never Mix Methods: An electrical label or safety plan cannot state "Incident Energy = 6.2 cal/cm 2 6.2\text{ cal/cm}^2 6.2 cal/cm 2 , PPE Category 2". NFPA 70E strictly prohibits mixing the Incident Energy Analysis method and the PPE Category Table method for the same piece of equipment.
Equipment Arc-Flash Labeling Requirements (NEC 110.16 & NFPA 70E 130.5(H))
Electrical equipment such as switchboards, panelboards, industrial control panels, meter socket enclosures, and motor control centers must be field-marked with a permanent arc-flash warning label containing:
- Nominal System Voltage
- Arc-Flash Boundary
At least one of the following:
- Available incident energy and corresponding working distance, OR
- Minimum arc rating of clothing, OR
Required level of PPE (or PPE Category, if table method was used).
Date of calculation/review (NFPA 70E requires incident energy studies to be reviewed at least once every 5 years or whenever major system modifications occur).
- 5. Worked Incident Energy & TCC Clearing Time Problem
- Problem Scenario
A 480 V 480\text{ V} 480 V , 3-phase, 60 Hz 60\text{ Hz} 60 Hz motor control center (MCC) with an HCB electrode configuration is fed by an upstream low-voltage power circuit breaker equipped with an electronic trip unit. The calculated bolted fault current is I b f = 25 kA I_{bf} = 25\text{ kA} I b f = 25 kA .
From IEEE 1584 equations, the calculated 100% arcing current is I a r c = 13.0 kA I_{arc} = 13.0\text{ kA} I a rc = 13.0 kA , and the reduced arcing current (85%) is I a r c _ 85 = 11.05 kA I_{arc\_85} = 11.05\text{ kA} I a rc _85 = 11.05 kA .
The upstream breaker TCC exhibits the following trip response:
At I = 13.0 kA I = 13.0\text{ kA} I = 13.0 kA : Breaker operates in its instantaneous pickup region with total clearing time t 1 = 0.05 s t_1 = 0.05\text{ s} t 1 = 0.05 s (3 cycles).
At I = 11.05 kA I = 11.05\text{ kA} I = 11.05 kA : The current falls just below the instantaneous pickup setting ( 12.0 kA 12.0\text{ kA} 12.0 kA ) into the short-time delay band with total clearing time t 2 = 0.35 s t_2 = 0.35\text{ s} t 2 = 0.35 s .
At a working distance D = 18 in D = 18\text{ in} D = 18 in , the simplified IEEE 1584 normalized incident energy equations yield: E 1 = 1.85 cal/cm 2 ( for I a r c = 13.0 kA , t 1 = 0.05 s ) E_1 = 1.85\text{ cal/cm}^2 \quad (\text{for } I_{arc} = 13.0\text{ kA}, t_1 = 0.05\text{ s}) E 1 = 1.85 cal/cm 2 ( for I a rc = 13.0 kA , t 1 = 0.05 s ) E 2 = 11.20 cal/cm 2 ( for I a r c _ 85 = 11.05 kA , t 2 = 0.35 s ) E_2 = 11.20\text{ cal/cm}^2 \quad (\text{for } I_{arc\_85} = 11.05\text{ kA}, t_2 = 0.35\text{ s}) E 2 = 11.20 cal/cm 2 ( for I a rc _85 = 11.05 kA , t 2 = 0.35 s )
Determine:
The governing incident energy for PPE selection.
The minimum arc rating required for worker PPE.
The Arc-Flash Boundary (AFB) given the empirical relation AFB = D ⋅ E g o v 1.2 \text{AFB} = D \cdot \sqrt{\frac{E_{gov}}{1.2}} AFB = D ⋅ 1.2 E g o v . Step-by-Step Solution:
Step 1: Determine Governing Incident Energy
Evaluating 100% arcing current:
E_1 = 1.85 cal/cm²
Evaluating 85% arcing current (reduced):
E_2 = 11.20 cal/cm²
Per IEEE 1584, Governing Incident Energy:
E_gov = MAX(E_1, E_2) = MAX(1.85, 11.20) = 11.20 cal/cm².
Step 2: Minimum Required Arc Rating
The worker's arc-rated PPE must equal or exceed E_gov:
Arc Rating >= 11.20 cal/cm².
(A standard 12 cal/cm² or 20 cal/cm² AR daily wear / flash suit system is required).
- Step 3: Calculate Arc-Flash Boundary (AFB)
- AFB = D * sqrt(E_gov / 1.2)
- AFB = 18 in * sqrt(11.20 / 1.2)
AFB = 18 in * sqrt(9.333) = 18 * 3.055 = 54.99 in ~= 4 ft 7 in (1.40 m).
Key Takeaway: Because 11.05 kA fell below the instantaneous pickup setting, clearing time
jumped from 50 ms to 350 ms, multiplying incident energy by a factor of 6.05!