Study guide

1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery

PE Electrical and Computer: Power Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Strategy & Reference Handbook

1.1 PE Power Exam Format, CBT Navigation & Reference Handbook 1.2 2026 Reference Standards (NEC 2020, NFPA 70E-2021, NESC) & Scoring Mechanics 1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery

2 Chapter 2: Measurement, Metering & Field Testing

2.1 Current Transformers (CTs), Potential Transformers (PTs) & Meter Connections 2.2 Instrument Transformer Burdens, Saturation Curves & Ratio Correction Factors 2.3 Insulation Resistance Testing (Megger, Polarization Index, Dielectric Absorption) 2.4 Ground Resistance Testing (Fall-of-Potential 62% Rule & Clamp-on Methods)

3 Chapter 3: General Applications — Grounding & Surge Protection

3.1 Substation Ground Grid Design & IEEE 80 Touch/Step Voltage Criteria 3.2 Lightning Protection Systems & Rolling Sphere / Cone of Protection Methods 3.3 Surge Protective Devices (SPDs) & Voltage Surge Arresters

4 Chapter 4: General Applications — Lighting & Energy Management

4.1 Illumination Engineering & Zonal Cavity / Lumen Method Calculations 4.2 Energy Management, Demand Factors & Load Factor Calculations 4.3 Economic Dispatch, Energy Efficiency & Load Profile Analysis

5 Chapter 5: Electrical Safety & NFPA Standards

5.1 NFPA 70E Shock Protection, Approach Boundaries & PPE Requirements 5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations 5.3 Hazardous (Classified) Locations (Class I, II, III & Division/Zone Systems) 5.4 Special Occupancies & Critical Systems (NEC Articles 517 Health Care, 700/701/702 Emergency)

6 Chapter 6: NEC Wiring Methods & Installation Requirements

6.1 Conductor Ampacity & NEC Table 310.16 Derating Adjustments 6.2 Raceway Fill, Box Sizing & Conduit Bending Calculations (Chapter 9 Tables) 6.3 Equipment Grounding Conductors & Grounding Electrode Sizing (NEC Article 250)

7 Chapter 7: Circuit Analysis — Fundamentals & Symmetrical Components

7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition) 7.2 Balanced Three-Phase Circuits (Wye-Delta Configurations & Power Formulas) 7.3 Symmetrical Components & Fortescue Sequence Transformation Matrices 7.4 Sequence Impedances & Positive, Negative, Zero Sequence Network Construction

8 Chapter 8: Circuit Analysis — Per-Unit & Phasor Analysis

8.1 Per-Unit System Fundamentals & Base Conversion Formulas 8.2 Three-Phase Per-Unit Network Modeling & Equipment Impedance Conversion 8.3 Phasor Diagrams, Complex Power & Power Triangle Relationships

9 Chapter 9: Power Electronics & Logic Controls

9.1 Power Electronic Converters (Rectifiers, Inverters & DC-DC Topologies) 9.2 Inverter-Based Resources (IBRs), Grid-Forming & Grid-Following Controls 9.3 Variable Frequency Drives (VFDs), PWM Operation & Harmonic Mitigation 9.4 Boolean Algebra, Logic Gates, De Morgan's Laws & Ladder Logic Control Diagrams

10 Chapter 10: Rotating Machines — Induction & Synchronous

10.1 Three-Phase Induction Motors (Equivalent Circuits, Slip & Performance) 10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes 10.3 Synchronous Machines (Operating Principles, Power-Angle Curves & V-Curves) 10.4 Motor Starting Methods (DOL, Wye-Delta, Autotransformer, Soft-Start) & Voltage Dip

11 Chapter 11: Electric Power Devices & Renewable Energy

11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation) 11.2 Power Factor Correction Capacitors & Shunt Bank Sizing 11.3 Battery Energy Storage Systems (BESS) & Ultracapacitors 11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)

12 Chapter 12: Transmission & Distribution — Steady-State & Power Quality

12.1 Transmission Line Modeling, Voltage Drop & Conductor Sizing 12.2 Voltage Regulation, Reactive Power Support & Tap-Changer Controls 12.3 Power Quality, Harmonics, THD & IEEE 519 Compliance 12.4 Power Flow Analysis & System Stability (Steady-State, Transient & Swing Equation)

13 Chapter 13: Transmission & Distribution — Fault Analysis & Transformer Shifts

13.1 Symmetrical Three-Phase Bolted Fault Calculations 13.2 Unsymmetrical Fault Analysis (SLG, L-L, DLG Fault Calculations) 13.3 Transformer Connection Types, Zero-Sequence Paths & 30-Degree Phase Shifts

14 Chapter 14: Protection Systems & Device Coordination

14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves 14.2 Protective Relaying Schemes (Differential 87, Distance 21, Undervoltage 27) 14.3 Circuit Breakers, Fuses & Automatic Reclosers 14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)

1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery

Key Takeaways Explain This Topic AI

Alternative Item Types (AITs)—including Multiple Correct, Point-and-Click, Drag-and-Drop, and Fill-in-the-Blank—award zero partial credit; complete accuracy is required.

The 3-Pass Execution Strategy allocates test time dynamically: Pass 1 secures immediate lookup wins (<2.5 min), Pass 2 executes standard calculations (4-6 min), and Pass 3 tackles complex synthesis.

Three-phase unit conversions and power equations ( S = 3 V L L I L S = \sqrt{3}V_{LL}I_L S = 3 ​ V LL ​ I L ​ ) require constant dimensional verification to avoid mixing line-to-line and line-to-neutral quantities.

Per-unit impedance base transformation calculations require precise application of voltage and MVA base scaling formulas ( Z p u , n e w = Z p u , o l d ⋅ ( V o l d / V n e w ) 2 ⋅ ( S n e w / S o l d ) Z_{pu,new} = Z_{pu,old} \cdot (V_{old}/V_{new})^2 \cdot (S_{new}/S_{old}) Z p u , n e w ​ = Z p u , o l d ​ ⋅ ( V o l d ​ / V n e w ​ ) 2 ⋅ ( S n e w ​ / S o l d ​ ) ).

Last updated: August 2026

1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery

Executive Overview: Passing the PE Power examination demands rigorous execution discipline. Beyond standard multiple-choice questions, NCEES incorporates non-traditional Alternative Item Types (AITs) that test engineering judgment interactively. To finish all 80 questions with sufficient time for review, candidates must combine a structured Three-Pass pacing workflow with absolute fluency in power system unit conversions and per-unit transformations.

1. Alternative Item Types (AITs) Demystified

Alternative Item Types constitute approximately 15% to 25% of the PE Power exam . AIT questions are engineered to test deep comprehension and prevent reverse-engineering solutions from four multiple-choice options. +--------------------------------------------------------------------------+

  • | FOUR ALTERNATIVE ITEM TYPES (AITs) ON THE CBT PE POWER EXAM |
  • | |
  • | 1. MULTIPLE CORRECT OPTIONS 2. POINT-AND-CLICK (HOTSPOT) |
  • | [x] Option A Click on the single faulted bus: |
  • | [ ] Option B (Bus 1) --- [x] (Bus 2) |
  • | [x] Option C | |
  • | (Square checkboxes; no partial) (Gen 1) |
  • | |
  • | 3. DRAG-AND-DROP / MATCHING 4. FILL-IN-THE-BLANK (NUMERICAL ENTRY) |
  • | [50/51] -> [Feeder Overcurrent] Type numeric value: |
  • | [ 87 ] -> [Transformer Diff ] [ 114.35 ] kVAR |
  • | [ 27 ] -> [Bus Undervoltage ] (Acceptable tolerance: +/- 1-2%) |
  • +--------------------------------------------------------------------------+
  • Detailed Analysis of AIT Formats

Multiple Correct Options (Select All That Apply):

Visual Indicator: Displayed with square check-boxes instead of circular radio buttons.

Prompt Phrasing: The question may specify an exact count (e.g., "Select two options." ) or open-ended phrasing (e.g., "Select all that apply." ).

Scoring Reality: Zero partial credit is awarded. If a question requires three selections, selecting two correct options and omitting the third yields a score of zero.

Point-and-Click (Hotspot Questions):

Mechanism: The candidate must click within a specific target area on a graphical schematic, Time-Current Characteristic (TCC) curve, or phasor diagram.

Precision Requirement: Scoring algorithms establish an invisible rectangular coordinate zone around the correct element. Click cleanly inside the component symbol, bus node, or curve region.

Drag-and-Drop / Matching:

Mechanism: Examinees drag labels or component blocks from a source pool into target slots.

Common Power Applications: Matching ANSI/IEEE device function numbers (e.g., Device 50 = Instantaneous Overcurrent, Device 51 = Time Overcurrent, Device 87 = Differential, Device 59 = Overvoltage, Device 27 = Undervoltage) to their protective locations, or sequencing high-voltage switching steps.

Fill-in-the-Blank (Numerical Entry):

Mechanism: A single text entry box where candidates type a calculated numerical answer.

Precision & Tolerances: Pay meticulous attention to the requested unit (e.g., typing 114.3 if the label outside the box reads kVAR , not 114300 ). NCEES programs an acceptance tolerance band (typically ± 1 % \pm1\% ± 1% to ± 2 % \pm2\% ± 2% ) to accommodate minor rounding variations.

2. The 3-Pass Time Management Strategy

With 80 questions across 480 minutes of active testing, you have an average of 6.0 minutes per question . However, question difficulty varies from 90-second conceptual lookups to 9-minute multi-loop calculations. The 3-Pass Strategy guarantees that you bank all high-probability points before spending time on time-intensive problems.

Pacing Model per 40-Question Module (240 Minutes)

Execution Pass Target Time Allocation Objective & Problem Selection Criteria

Pass 1: Rapid Wins Minutes 0 to 60 (~1.5 to 2.5 min/item) • Solve all direct Handbook lookup formulas, straightforward definitions, single-step arithmetic, and code questions with known article locations.; • Target: Complete 15-20 questions immediately.; • Rule: If a question requires extensive multi-step algebra or unfamiliar searching, enter your best immediate guess, flag it, and move forward instantly.

Pass 2: Core Engineering Minutes 60 to 190 (~4.5 to 6.0 min/item) • Solve standard 2-to-3 step calculations: symmetrical components, transformer equivalent circuits, power factor capacitor sizing, voltage drop, motor starting curves.; • Target: Complete 15-18 additional questions.; • Rule: Set a strict 7-minute ceiling. If a calculation gets bogged down in algebra, flag it and defer to Pass 3.

Pass 3: Deep Synthesis Minutes 190 to 235 (~7.0 to 9.0 min/item) • Attack remaining flagged questions: complex fault analysis, long NEC ampacity derating calculations with multiple adjustment factors, and tricky AIT drag-and-drop items.

Final Review & Lock Minutes 235 to 240 (Last 5 minutes) • Open the Pearson VUE Review Screen.; • Verify that unanswered count is exactly 0 .; • Confirm guesses on any remaining flagged questions before submitting.

3. Power Engineering Unit Conversions & Dimensional Rigor

Calculation blunders on the PE Power exam frequently stem from unit mismatch errors rather than conceptual misunderstandings. Master these core relationships:

Balanced Three-Phase Power Formulas S 3 ϕ = 3 V L L I L = 3 V L N I p h [ kVA or MVA ] S_{3\phi} = \sqrt{3} V_{LL} I_L = 3 V_{LN} I_{ph} \quad [\text{kVA or MVA}] S 3 ϕ ​ = 3 ​ V LL ​ I L ​ = 3 V L N ​ I p h ​ [ kVA or MVA ] P 3 ϕ = 3 V L L I L cos ⁡ θ = 3 V L N I p h cos ⁡ θ [ kW or MW ] P_{3\phi} = \sqrt{3} V_{LL} I_L \cos\theta = 3 V_{LN} I_{ph} \cos\theta \quad [\text{kW or MW}] P 3 ϕ ​ = 3 ​ V LL ​ I L ​ cos θ = 3 V L N ​ I p h ​ cos θ [ kW or MW ] Q 3 ϕ = 3 V L L I L sin ⁡ θ = 3 V L N I p h sin ⁡ θ [ kVAR or MVAR ] Q_{3\phi} = \sqrt{3} V_{LL} I_L \sin\theta = 3 V_{LN} I_{ph} \sin\theta \quad [\text{kVAR or MVAR}] Q 3 ϕ ​ = 3 ​ V LL ​ I L ​ sin θ = 3 V L N ​ I p h ​ sin θ [ kVAR or MVAR ]

The 3 \sqrt{3} 3 ​ and Wye/Delta Conversion Rules

Voltage Convention: Unless explicitly stated otherwise as "phase voltage" or "line-to-neutral", all voltages in power system problems are three-phase line-to-line voltages ( V L L V_{LL} V LL ​ ) .

Current Convention: All line currents in balanced systems represent the actual current entering the terminal ( I L I_L I L ​ ).

In Wye (Y) Connections: V L L = 3 V L N ∠ + 30 ∘ V_{LL} = \sqrt{3} V_{LN} \angle +30^\circ V LL ​ = 3 ​ V L N ​ ∠ + 3 0 ∘ and I L = I p h I_L = I_{ph} I L ​ = I p h ​ .

In Delta ( Δ \Delta Δ ) Connections: V L L = V p h V_{LL} = V_{ph} V LL ​ = V p h ​ and I L = 3 I p h ∠ − 30 ∘ I_L = \sqrt{3} I_{ph} \angle -30^\circ I L ​ = 3 ​ I p h ​ ∠ − 3 0 ∘ .

Per-Unit System Base Transformations

When altering impedance bases across transformer boundaries or system studies, apply the universal per-unit base scaling formula from the NCEES handbook's circuit analysis section: Z b a s e = ( V b a s e , L L ) 2 S b a s e , 3 ϕ = ( k V b a s e , L L ) 2 M V A b a s e , 3 ϕ [ Ω ] Z_{base} = \frac{(V_{base,LL})^2}{S_{base,3\phi}} = \frac{(kV_{base,LL})^2}{MVA_{base,3\phi}} \quad [\Omega] Z ba se ​ = S ba se , 3 ϕ ​ ( V ba se , LL ​ ) 2 ​ = M V A ba se , 3 ϕ ​ ( k V ba se , LL ​ ) 2 ​ [ Ω ] Z p u , n e w = Z p u , o l d × ( V b a s e , o l d V b a s e , n e w ) 2 × ( S b a s e , n e w S b a s e , o l d ) Z_{pu,new} = Z_{pu,old} \times \left(\frac{V_{base,old}}{V_{base,new}}\right)^2 \times \left(\frac{S_{base,new}}{S_{base,old}}\right) Z p u , n e w ​ = Z p u , o l d ​ × ( V ba se , n e w ​ V ba se , o l d ​ ​ ) 2 × ( S ba se , o l d ​ S ba se , n e w ​ ​ )

Exam Trap Alert: A classic trap is inverting the voltage ratio. Notice that V b a s e , o l d V_{base,old} V ba se , o l d ​ is in the numerator and V b a s e , n e w V_{base,new} V ba se , n e w ​ is in the denominator, which is the inverse of the power ratio where S b a s e , n e w S_{base,new} S ba se , n e w ​ is in the numerator.

Loading diagram... Visual Timeline of the 3-Pass Module Execution Strategy

  • 4. Worked Technical Calculations
  • Worked Example 1: Three-Phase Power Factor Correction

Problem: A 480 V (line-to-line), 3-phase, 60 Hz commercial facility draws 250 kVA 250\text{ kVA} 250 kVA at 0.72 0.72 0.72 power factor lagging . Determine the required reactive power rating in kVAR \text{kVAR} kVAR of a three-phase wye-connected capacitor bank to correct the overall facility power factor to 0.95 0.95 0.95 lagging , and calculate the resulting reduction in line current. Step 1: Determine initial real (P) and reactive (Q1) power

  • Initial apparent power: S1 = 250 kVA
  • Initial power factor: cos(theta1) = 0.72 => theta1 = arccos(0.72) = 43.95 deg
  • Real power: P = S1 * cos(theta1) = 250 * 0.72 = 180.0 kW
  • Initial reactive power: Q1 = S1 * sin(theta1) = 250 * sin(43.95 deg) = 173.50 kVAR
  • Step 2: Determine target reactive power (Q2) at 0.95 PF lagging
  • Target power factor: cos(theta2) = 0.95 => theta2 = arccos(0.95) = 18.19 deg
  • Target reactive power: Q2 = P * tan(theta2) = 180.0 * tan(18.19 deg) = 59.16 kVAR
  • Step 3: Calculate required capacitor bank rating (Q_c)
  • Q_c = Q1 - Q2 = 173.50 kVAR - 59.16 kVAR = 114.34 kVAR
  • Step 4: Calculate line current reduction
  • Initial line current: I_L1 = S1 / (sqrt(3) * V_LL) = 250,000 / (sqrt(3) * 480) = 300.70 A
  • New apparent power: S2 = P / cos(theta2) = 180.0 / 0.95 = 189.47 kVA
  • New line current: I_L2 = S2 / (sqrt(3) * V_LL) = 189,470 / (sqrt(3) * 480) = 227.91 A
  • Current reduction: Delta_I_L = 300.70 A - 227.91 A = 72.79 A (24.2% reduction)
  • Worked Example 2: Per-Unit System Base Transformation

Problem: A 15 MVA 15\text{ MVA} 15 MVA , 13.8 kV / 4.16 kV 13.8\text{ kV} / 4.16\text{ kV} 13.8 kV /4.16 kV three-phase substation transformer has a nameplate leakage reactance of X = 0.080 pu X = 0.080\text{ pu} X = 0.080 pu based on its own ratings. Calculate the new per-unit reactance of this transformer when integrated into a power system model with system bases of 100 MVA 100\text{ MVA} 100 MVA and 13.2 kV 13.2\text{ kV} 13.2 kV on the primary side. Given Transformer Parameters:

  • S_base_old = 15 MVA
  • V_base_old = 13.8 kV (primary)
  • X_pu_old = 0.080 pu

System Base Parameters:

  • S_base_new = 100 MVA
  • V_base_new = 13.2 kV (primary)

Calculation using Base Conversion Formula:

  • X_pu_new = X_pu_old * (V_base_old / V_base_new)^2 * (S_base_new / S_base_old)
  • X_pu_new = 0.080 * (13.8 kV / 13.2 kV)^2 * (100 MVA / 15 MVA)
  • X_pu_new = 0.080 * (1.04545)^2 * (6.6667)
  • X_pu_new = 0.080 * 1.0930 * 6.6667 = 0.5830 pu

Conclusion:

The transformer per-unit reactance on the 100 MVA, 13.2 kV system base is 0.583 pu.

5. Strategic Traps & Formula Sheet Mastery Checklist

Line-to-Line vs. Line-to-Neutral Mixing: Forgetting to divide line voltage by 3 \sqrt{3} 3 ​ when computing per-phase equivalent circuit impedance ( Z p h = V L N / I L Z_{ph} = V_{LN} / I_L Z p h ​ = V L N ​ / I L ​ ).

Inverting the Per-Unit Voltage Ratio: Squaring ( V n e w / V o l d ) (V_{new}/V_{old}) ( V n e w ​ / V o l d ​ ) instead of ( V o l d / V n e w ) (V_{old}/V_{new}) ( V o l d ​ / V n e w ​ ) .

AIT Unit Prefix Omission: Writing 583000 instead of 583 when the prompt requests answers in kVA or pu .

Checkbox Indecision: Leaving a multiple-select checkbox partially answered because of doubt on a third choice. Evaluate every checkbox independently as a true/false proposition.