Study guide

14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves

PE Electrical and Computer: Power Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Strategy & Reference Handbook

1.1 PE Power Exam Format, CBT Navigation & Reference Handbook 1.2 2026 Reference Standards (NEC 2020, NFPA 70E-2021, NESC) & Scoring Mechanics 1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery

2 Chapter 2: Measurement, Metering & Field Testing

2.1 Current Transformers (CTs), Potential Transformers (PTs) & Meter Connections 2.2 Instrument Transformer Burdens, Saturation Curves & Ratio Correction Factors 2.3 Insulation Resistance Testing (Megger, Polarization Index, Dielectric Absorption) 2.4 Ground Resistance Testing (Fall-of-Potential 62% Rule & Clamp-on Methods)

3 Chapter 3: General Applications — Grounding & Surge Protection

3.1 Substation Ground Grid Design & IEEE 80 Touch/Step Voltage Criteria 3.2 Lightning Protection Systems & Rolling Sphere / Cone of Protection Methods 3.3 Surge Protective Devices (SPDs) & Voltage Surge Arresters

4 Chapter 4: General Applications — Lighting & Energy Management

4.1 Illumination Engineering & Zonal Cavity / Lumen Method Calculations 4.2 Energy Management, Demand Factors & Load Factor Calculations 4.3 Economic Dispatch, Energy Efficiency & Load Profile Analysis

5 Chapter 5: Electrical Safety & NFPA Standards

5.1 NFPA 70E Shock Protection, Approach Boundaries & PPE Requirements 5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations 5.3 Hazardous (Classified) Locations (Class I, II, III & Division/Zone Systems) 5.4 Special Occupancies & Critical Systems (NEC Articles 517 Health Care, 700/701/702 Emergency)

6 Chapter 6: NEC Wiring Methods & Installation Requirements

6.1 Conductor Ampacity & NEC Table 310.16 Derating Adjustments 6.2 Raceway Fill, Box Sizing & Conduit Bending Calculations (Chapter 9 Tables) 6.3 Equipment Grounding Conductors & Grounding Electrode Sizing (NEC Article 250)

7 Chapter 7: Circuit Analysis — Fundamentals & Symmetrical Components

7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition) 7.2 Balanced Three-Phase Circuits (Wye-Delta Configurations & Power Formulas) 7.3 Symmetrical Components & Fortescue Sequence Transformation Matrices 7.4 Sequence Impedances & Positive, Negative, Zero Sequence Network Construction

8 Chapter 8: Circuit Analysis — Per-Unit & Phasor Analysis

8.1 Per-Unit System Fundamentals & Base Conversion Formulas 8.2 Three-Phase Per-Unit Network Modeling & Equipment Impedance Conversion 8.3 Phasor Diagrams, Complex Power & Power Triangle Relationships

9 Chapter 9: Power Electronics & Logic Controls

9.1 Power Electronic Converters (Rectifiers, Inverters & DC-DC Topologies) 9.2 Inverter-Based Resources (IBRs), Grid-Forming & Grid-Following Controls 9.3 Variable Frequency Drives (VFDs), PWM Operation & Harmonic Mitigation 9.4 Boolean Algebra, Logic Gates, De Morgan's Laws & Ladder Logic Control Diagrams

10 Chapter 10: Rotating Machines — Induction & Synchronous

10.1 Three-Phase Induction Motors (Equivalent Circuits, Slip & Performance) 10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes 10.3 Synchronous Machines (Operating Principles, Power-Angle Curves & V-Curves) 10.4 Motor Starting Methods (DOL, Wye-Delta, Autotransformer, Soft-Start) & Voltage Dip

11 Chapter 11: Electric Power Devices & Renewable Energy

11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation) 11.2 Power Factor Correction Capacitors & Shunt Bank Sizing 11.3 Battery Energy Storage Systems (BESS) & Ultracapacitors 11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)

12 Chapter 12: Transmission & Distribution — Steady-State & Power Quality

12.1 Transmission Line Modeling, Voltage Drop & Conductor Sizing 12.2 Voltage Regulation, Reactive Power Support & Tap-Changer Controls 12.3 Power Quality, Harmonics, THD & IEEE 519 Compliance 12.4 Power Flow Analysis & System Stability (Steady-State, Transient & Swing Equation)

13 Chapter 13: Transmission & Distribution — Fault Analysis & Transformer Shifts

13.1 Symmetrical Three-Phase Bolted Fault Calculations 13.2 Unsymmetrical Fault Analysis (SLG, L-L, DLG Fault Calculations) 13.3 Transformer Connection Types, Zero-Sequence Paths & 30-Degree Phase Shifts

14 Chapter 14: Protection Systems & Device Coordination

14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves 14.2 Protective Relaying Schemes (Differential 87, Distance 21, Undervoltage 27) 14.3 Circuit Breakers, Fuses & Automatic Reclosers 14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)

14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves

Key Takeaways Explain This Topic AI

Overcurrent protection pairs Instantaneous (ANSI 50) elements operating without intentional delay (<40 ms) above a high fault threshold with Time-Overcurrent (ANSI 51) elements operating along an inverse time curve where trip time decreases as current rises.

Standard IEEE C37.112 inverse time curves follow t ( I ) = T D ( A M p − 1 + B ) t(I) = TD \left( \frac{A}{M^p - 1} + B \right) t ( I ) = T D ( M p − 1 A ​ + B ) where M = I / I p i c k u p M = I / I_{pickup} M = I / I p i c k u p ​ , spanning Moderately Inverse ( p = 0.02 , A = 0.0515 , B = 0.1140 p=0.02, A=0.0515, B=0.1140 p = 0.02 , A = 0.0515 , B = 0.1140 ), Very Inverse ( p = 2.0 , A = 19.61 , B = 0.491 p=2.0, A=19.61, B=0.491 p = 2.0 , A = 19.61 , B = 0.491 ), and Extremely Inverse ( p = 2.0 , A = 28.2 , B = 0.1217 p=2.0, A=28.2, B=0.1217 p = 2.0 , A = 28.2 , B = 0.1217 ).

Pickup current ( I p i c k u p I_{pickup} I p i c k u p ​ ) selection enforces a strict dual boundary: I p i c k u p ≥ 1.25 to 1.50 × I l o a d , m a x I_{pickup} \ge 1.25 \text{ to } 1.50 \times I_{load,max} I p i c k u p ​ ≥ 1.25 to 1.50 × I l o a d , ma x ​ to prevent spurious tripping under peak/inrush conditions, and I p i c k u p ≤ 0.50 to 0.80 × I f a u l t , m i n I_{pickup} \le 0.50 \text{ to } 0.80 \times I_{fault,min} I p i c k u p ​ ≤ 0.50 to 0.80 × I f a u lt , min ​ to ensure sensitive clearance of remote bolted and arcing faults.

Electromechanical relays feature induction disk inertia with reset times governed by t r e s e t = T D ( t r 1 − M 2 ) t_{reset} = TD \left( \frac{t_r}{1 - M^2} \right) t rese t ​ = T D ( 1 − M 2 t r ​ ​ ) , causing ratchet accumulation during fast reclosing cycles, whereas modern numerical relays implement instantaneous or linear emulated resets.

Log-log TCC curves plot operating time (0.01 s to 1000 s) against current multiples or primary amperes (10 A to 100 kA), requiring all downstream and upstream devices to be plotted on a single, common voltage reference base.

Last updated: August 2026

14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves

Executive Overview: Overcurrent protection is the foundational protection philosophy across electric utility distribution, industrial networks, and commercial power systems. On the NCEES PE Power examination, overcurrent protection problems require absolute mastery of ANSI 50 (Instantaneous) vs. ANSI 51 (Time-Overcurrent) operating dynamics, mathematical parameterization of IEEE C37.112 and IEC 60255 inverse-time curves, Current Transformer (CT) tap/pickup current sizing, Time Dial ( T D TD T D ) calibration, and the interpretation of log-log Time-Current Characteristic (TCC) plots across transformer voltage boundaries.

1. ANSI 50 vs. ANSI 51 Functional Architecture

Overcurrent relays detect abnormal current magnitudes resulting from phase-to-phase, three-phase bolted, or phase-to-ground faults. The fundamental ANSI device designations define their operating speed and time-delay mechanics: Overcurrent Relay Functional Elements & Operating Time Profile:

  • Time (s) ^
  • |
  • 10.0 |---. ANSI 51: Time-Overcurrent Characteristic
  • | \
  • 1.0 | \ t(I) = TD * [ A / (M^p - 1) + B ]

| `.

0.1 | `--.

  • | | ANSI 50: Instantaneous Element
  • 0.02 |-----------+-------------------> Operating Time (< 2 cycles / 33 ms)
  • | | Intentional Delay = 0
  • +-----------+---------------------> Current (A)
  • I_pickup I_inst_pickup
  • Instantaneous Overcurrent (ANSI 50)

Operating Principle: Evaluates current magnitude continuously against a fixed threshold I i n s t I_{inst} I in s t ​ . When I m e a s u r e d > I i n s t I_{measured} > I_{inst} I m e a s u re d ​ > I in s t ​ , the relay issues a trip command to the circuit breaker with no intentional time delay .

Operating Speed: Total clearing time is governed solely by relay measurement/filtering algorithms ( 10 − 25 ms 10-25\text{ ms} 10 − 25 ms ) and circuit breaker contact parting time ( 30 − 50 ms 30-50\text{ ms} 30 − 50 ms for standard 3-cycle or 5-cycle breakers), yielding total clearing in < 40 − 80 ms <40-80\text{ ms} < 40 − 80 ms .

Setting Constraint: To maintain selectivity, ANSI 50 pickup must be set above the maximum symmetrical fault current available at the next downstream protective device terminal ( I 50 ≥ 1.20 − 1.30 × I f a u l t , d o w n s t r e a m I_{50} \ge 1.20 - 1.30 \times I_{fault,downstream} I 50 ​ ≥ 1.20 − 1.30 × I f a u lt , d o w n s t re am ​ ) to prevent "overreaching" and tripping on out-of-zone faults.

Time-Overcurrent (ANSI 51)

Operating Principle: Operates along an inverse time-current characteristic where the operating time t o p t_{op} t o p ​ decreases non-linearly as current magnitude increases.

Functional Benefit: Provides thermal protection for conductors and equipment at moderate overloads while enabling selective time-grading between series-connected protective devices.

Secondary Designations:

51P / 50P: Phase overcurrent elements driven by phase CTs.

51N / 50N: Residual ground overcurrent elements calculating 3 I 0 = I a + I b + I c 3\mathbf{I}_0 = \mathbf{I}_a + \mathbf{I}_b + \mathbf{I}_c 3 I 0 ​ = I a ​ + I b ​ + I c ​ internally or from residual CT connections.

51G / 50G: Dedicated zero-sequence ground overcurrent elements driven by a core-balance (toroidal / window-type) CT encircling all three phase conductors.

  • 2. Standardized Inverse-Time Curve Equations
  • IEEE C37.112-2018 Standard Equation

The standard mathematical representation for IEEE/ANSI inverse-time overcurrent relays is defined by: t ( I ) = T D ( A M p − 1 + B ) [ seconds ] t(I) = TD \left( \frac{A}{M^p - 1} + B \right) \quad [\text{seconds}] t ( I ) = T D ( M p − 1 A ​ + B ) [ seconds ]

where:

T D TD T D = Time Dial setting (multiplier adjusting the vertical position of the curve, typically 0.5 0.5 0.5 to 15.0 15.0 15.0 in electromechanical relays or 0.05 0.05 0.05 to 10.0 10.0 10.0 in digital relays).

M M M = Multiple of pickup current, defined as M = I a c t u a l I p i c k u p = I s e c o n d a r y I t a p = I p r i m a r y I p i c k u p , p r i M = \frac{I_{actual}}{I_{pickup}} = \frac{I_{secondary}}{I_{tap}} = \frac{I_{primary}}{I_{pickup,pri}} M = I p i c k u p ​ I a c t u a l ​ ​ = I t a p ​ I seco n d a ry ​ ​ = I p i c k u p , p r i ​ I p r ima ry ​ ​ .

A , B , p A, B, p A , B , p = Dimensionless curve shape constants defining the degree of inverseness.

IEEE / ANSI Curve Class A A A B B B p p p Primary System Application

IEEE Moderately Inverse 0.0515 0.0515 0.0515 0.1140 0.1140 0.1140 0.020 0.020 0.020 General distribution feeders with steady load profiles

IEEE Very Inverse 19.61 19.61 19.61 0.4910 0.4910 0.4910 2.000 2.000 2.000 Feeders with significant line impedance; fast clearance of high faults

IEEE Extremely Inverse 28.20 28.20 28.20 0.1217 0.1217 0.1217 2.000 2.000 2.000 Coordination with downstream power fuses; transformer inrush & cable thermal curves ( I 2 t I^2 t I 2 t )

IEEE Short-Time Inverse 0.00342 0.00342 0.00342 0.00262 0.00262 0.00262 0.020 0.020 0.020 Differential unrestrained backup; selective motor protection Comparison of IEEE Time-Current Curve Slopes (at TD = 1.0):

  • Time (s) ^
  • 10.0 | Moderately Inverse (gentle slope)
  • | \
  • 1.0 | \ Very Inverse (steeper slope)
  • | \ \
  • 0.1 | \ \ Extremely Inverse (steepest: ~ 1/I^2)
  • | \ \ \
  • 0.01 +--------+---+---+-------------------> Multiple of Pickup (M = I / I_pu)
  • 2 5 10 20
  • IEC 60255-151 Standard Curve Formulation

In international and industrial applications, the IEC standard curve family is formulated as: t ( I ) = T M S ⋅ ( k M α − 1 ) [ seconds ] t(I) = TMS \cdot \left( \frac{k}{M^\alpha - 1} \right) \quad [\text{seconds}] t ( I ) = TMS ⋅ ( M α − 1 k ​ ) [ seconds ]

where T M S TMS TMS is the Time Multiplier Setting ( 0.01 0.01 0.01 to 1.0 1.0 1.0 ) and parameters are:

  • IEC Class A (Standard Inverse): k = 0.14 , α = 0.02 k = 0.14, \alpha = 0.02 k = 0.14 , α = 0.02
  • IEC Class B (Very Inverse): k = 13.5 , α = 1.0 k = 13.5, \alpha = 1.0 k = 13.5 , α = 1.0
  • IEC Class C (Extremely Inverse): k = 80.0 , α = 2.0 k = 80.0, \alpha = 2.0 k = 80.0 , α = 2.0
  • IEC Long-Time Inverse: k = 120.0 , α = 1.0 k = 120.0, \alpha = 1.0 k = 120.0 , α = 1.0

Important

Extremely Inverse ( p = 2.0 , α = 2.0 p=2.0, \alpha=2.0 p = 2.0 , α = 2.0 ) Significance: The exponent p = 2.0 p=2.0 p = 2.0 generates an operating time that varies inversely with the square of the current ( t ∝ 1 / I 2 t \propto 1/I^2 t ∝ 1/ I 2 ), matching the thermal heating energy limit ( I 2 t = K I^2 t = K I 2 t = K ) of cables, transformers, and the clearing characteristics of high-voltage power fuses.

3. Overcurrent Relay Setting Methodology

Setting an ANSI 51 time-overcurrent relay requires establishing two primary parameters: the Pickup Current ( I p i c k u p I_{pickup} I p i c k u p ​ ) and the Time Dial ( T D TD T D ) . Relay Setting Optimization Window:

  • 0 A -----------------[ Security Boundary ]================[ Sensitivity Boundary ]-----------------> Fault kA
  • | |
  • Normal Peak Load ---->| ALLOWABLE PICKUP SETTING RANGE |<---- Minimum End-of-Line Fault
  • (I_load,max * 1.25) | ( I_pickup ) | ( I_fault,min * 0.80 )
  • Criterion 1: Pickup Current Setting ( I p i c k u p I_{pickup} I p i c k u p ​ or Tap Setting)

Continuous Load Security (Lower Bound): The relay must never pick up under maximum anticipated continuous load, emergency overload, or cold-load pickup inrush: I p i c k u p , p r i ≥ 1.25 to 1.50 × I l o a d , m a x I_{pickup,pri} \ge 1.25 \text{ to } 1.50 \times I_{load,max} I p i c k u p , p r i ​ ≥ 1.25 to 1.50 × I l o a d , ma x ​ For transformer primaries, I p i c k u p , p r i ≥ 1.25 to 1.50 × I F L A , O A I_{pickup,pri} \ge 1.25 \text{ to } 1.50 \times I_{FLA,OA} I p i c k u p , p r i ​ ≥ 1.25 to 1.50 × I F L A , O A ​ (where F L A FLA F L A is full-load amperes at maximum cooling rating).

Minimum Fault Sensitivity (Upper Bound): The relay must reliably detect the smallest possible fault current at the remote boundary of the protected zone under minimum generation conditions (line-to-line or minimum arcing line-to-ground fault): I p i c k u p , p r i ≤ 0.50 to 0.80 × I f a u l t , m i n I_{pickup,pri} \le 0.50 \text{ to } 0.80 \times I_{fault,min} I p i c k u p , p r i ​ ≤ 0.50 to 0.80 × I f a u lt , min ​

Secondary Relay Tap Calculation: I t a p , s e c = I p i c k u p , p r i C T R [ Amperes secondary ] I_{tap,sec} = \frac{I_{pickup,pri}}{CTR} \quad [\text{Amperes secondary}] I t a p , sec ​ = CTR I p i c k u p , p r i ​ ​ [ Amperes secondary ] where C T R = I p r i , r a t e d I s e c , r a t e d CTR = \frac{I_{pri,rated}}{I_{sec,rated}} CTR = I sec , r a t e d ​ I p r i , r a t e d ​ ​ is the Current Transformer Ratio (typically X : 5 A X:5\text{ A} X : 5 A or X : 1 A X:1\text{ A} X : 1 A ).

Criterion 2: Time Dial Selection ( T D TD T D )

The Time Dial is selected to achieve a target Coordination Time Interval ( C T I CTI CT I ) above the total clearing time of the immediate downstream protective device at the maximum through-fault current I f a u l t , m a x I_{fault,max} I f a u lt , ma x ​ : t u p s t r e a m ( I f a u l t , m a x ) ≥ t d o w n s t r e a m ( I f a u l t , m a x ) + C T I t_{upstream}(I_{fault,max}) \ge t_{downstream}(I_{fault,max}) + CTI t u p s t re am ​ ( I f a u lt , ma x ​ ) ≥ t d o w n s t re am ​ ( I f a u lt , ma x ​ ) + CT I

Substituting into the IEEE C37.112 equation and solving for T D TD T D : T D = t t a r g e t A M p − 1 + B = t d o w n s t r e a m ( I f a u l t , m a x ) + C T I A ( I f a u l t , m a x I p i c k u p ) p − 1 + B TD = \frac{t_{target}}{\frac{A}{M^p - 1} + B} = \frac{t_{downstream}(I_{fault,max}) + CTI}{\frac{A}{\left( \frac{I_{fault,max}}{I_{pickup}} \right)^p - 1} + B} T D = M p − 1 A ​ + B t t a r g e t ​ ​ = ( I p i c k u p ​ I f a u lt , ma x ​ ​ ) p − 1 A ​ + B t d o w n s t re am ​ ( I f a u lt , ma x ​ ) + CT I ​

4. Reset Characteristics: Electromechanical vs. Digital Relays

When a fault occurs and is cleared by a downstream device before an upstream relay reaches its trip threshold, the upstream relay must reset to its resting state. The reset mechanism fundamentally influences multi-shot automatic reclosing coordination. Induction Disk Dynamics vs. Microprocessor Linear Reset:

  • Relay Travel ^
  • 100% (TRIP)+-------------------------------------------------------
  • | Fault 1 Clearing Fault 2 (Reclose)
  • | / / /
  • 50% | / . - - - - -' / . - - - - (TRIP!)
  • | / / (Disk Coast/Reset) / /
  • 0% ------+---o-----------------------------o---------------------> Time (s)
  • Electromechanical: Partial Reset -> Premature Tripping (Ratcheting)
  • Digital Relay: Instantaneous / Programmed Reset to 0%
  • Electromechanical Induction Disk Relays (ANSI C37.90)

Operating Physics: An induction disk rotates against a restraining spiral spring. During an overcurrent condition, electromagnetic torque overcomes spring torque, driving the moving contact toward the stationary contact.

Disk Overtravel & Coasting: When current drops below pickup, rotational momentum causes the disk to continue moving forward for 0.05 − 0.10 s 0.05 - 0.10\text{ s} 0.05 − 0.10 s ("overtravel") before the spring reverses direction.

Reset Time Formulation: Disk reset time from the point of trip is given by: t r e s e t = T D ( t r 1 − M 2 ) for M < 1.0 t_{reset} = TD \left( \frac{t_r}{1 - M^2} \right) \quad \text{for } M < 1.0 t rese t ​ = T D ( 1 − M 2 t r ​ ​ ) for M < 1.0 where t r t_r t r ​ is the characteristic reset constant (typically 10 − 40 seconds 10 - 40\text{ seconds} 10 − 40 seconds for full travel). Because reset takes several seconds, fast auto-reclosers ( 0.3 − 0.5 s 0.3-0.5\text{ s} 0.3 − 0.5 s open interval) cause the disk to ratchet forward on successive shots, leading to premature upstream tripping.

Microprocessor (Digital / Numerical) Relays

Instantaneous Reset: Can be configured to reset the internal energy integrator to zero within 1 cycle ( 16.7 ms 16.7\text{ ms} 16.7 ms ) after current drops below 0.95 × I p i c k u p 0.95 \times I_{pickup} 0.95 × I p i c k u p ​ .

Emulated Electromechanical Reset: Microprocessor relays can also be programmed with linear or electromechanical induction disk reset characteristics to coordinate properly with legacy upstream electromechanical relays.

5. Log-Log TCC Curve Plotting Mechanics

Time-Current Characteristic curves are universally plotted on log-log coordinate grids spanning:

Vertical Axis (Time): 0.01 s 0.01\text{ s} 0.01 s ( 10 ms 10\text{ ms} 10 ms ) to 1000 s 1000\text{ s} 1000 s ( 16.6 minutes 16.6\text{ minutes} 16.6 minutes ).

Horizontal Axis (Current): 10 A 10\text{ A} 10 A to 100 , 000 A 100,000\text{ A} 100 , 000 A ( 100 kA 100\text{ kA} 100 kA ) plotted on a specified reference voltage base.

Essential TCC Construction Rules

Common Voltage Reference Base: When plotting devices across a transformer (e.g., 13.8 kV 13.8\text{ kV} 13.8 kV primary relay and 480 V 480\text{ V} 480 V secondary main breaker), all currents must be converted to a single reference base voltage using the turns ratio: I r e f = I a c t u a l × ( V a c t u a l V r e f ) I_{ref} = I_{actual} \times \left( \frac{V_{actual}}{V_{ref}} \right) I re f ​ = I a c t u a l ​ × ( V re f ​ V a c t u a l ​ ​ )

Transformer Inrush Point: An ANSI 51 relay curve must lie above and to the right of the transformer magnetizing inrush point:

Liquid-Filled Transformers: 8 × F L A 8 \times FLA 8 × F L A for 0.1 s 0.1\text{ s} 0.1 s and 12 × F L A 12 \times FLA 12 × F L A for 0.1 s 0.1\text{ s} 0.1 s (ANSI/IEEE C57.109).

Dry-Type Transformers: 12 − 14 × F L A 12 - 14 \times FLA 12 − 14 × F L A for 0.1 s 0.1\text{ s} 0.1 s .

Cable and Transformer Thermal Damage Curves:

Cable Damage Curve: t = K c u ⋅ A c m i l 2 I s c 2 t = \frac{K_{cu} \cdot A_{cmil}^2}{I_{sc}^2} t = I sc 2 ​ K c u ​ ⋅ A c mi l 2 ​ ​ (Onderdonk equation).

The upstream relay curve must sit strictly to the left and below the thermal damage curve of the protected equipment.

  • 6. Comprehensive Worked Relay Setting Calculation
  • Problem Statement

A 13.8 kV 13.8\text{ kV} 13.8 kV , 3-phase, 60 Hz 60\text{ Hz} 60 Hz distribution feeder is fed through a substation circuit breaker equipped with a microprocessor time-overcurrent relay (ANSI 51) using an IEEE Very Inverse curve ( A = 19.61 , B = 0.491 , p = 2.0 A = 19.61, B = 0.491, p = 2.0 A = 19.61 , B = 0.491 , p = 2.0 ).

  • CT Ratio: 600 : 5 A 600:5\text{ A} 600 : 5 A ( C T R = 120 CTR = 120 CTR = 120 )
  • Maximum Continuous Peak Load: I l o a d , m a x = 320 A I_{load,max} = 320\text{ A} I l o a d , ma x ​ = 320 A

Minimum Line-to-Line Fault Current (End of Feeder): I f a u l t , m i n = 1 , 800 A I_{fault,min} = 1,800\text{ A} I f a u lt , min ​ = 1 , 800 A

Maximum Through-Fault Current at Downstream Recloser: I f a u l t , m a x = 4 , 200 A I_{fault,max} = 4,200\text{ A} I f a u lt , ma x ​ = 4 , 200 A

Downstream Recloser Total Clearing Time at 4 , 200 A 4,200\text{ A} 4 , 200 A : t d o w n = 0.180 s t_{down} = 0.180\text{ s} t d o w n ​ = 0.180 s

Required Coordination Time Interval ( C T I CTI CT I ): 0.250 s 0.250\text{ s} 0.250 s

Maximum Bus Symmetrical Fault Current: I s c , b u s = 11 , 500 A I_{sc,bus} = 11,500\text{ A} I sc , b u s ​ = 11 , 500 A

Calculate:

The optimal primary pickup current I p i c k u p , p r i I_{pickup,pri} I p i c k u p , p r i ​ and secondary tap setting I t a p , s e c I_{tap,sec} I t a p , sec ​ .

Verify security against full load and sensitivity to minimum fault.

The multiple of pickup M M M at the coordination fault current ( 4 , 200 A 4,200\text{ A} 4 , 200 A ).

The required Time Dial ( T D TD T D ) setting to achieve the 0.250 s 0.250\text{ s} 0.250 s CTI.

The relay operating time at the maximum bus fault current ( 11 , 500 A 11,500\text{ A} 11 , 500 A ).

The instantaneous overcurrent (ANSI 50) pickup setting with a 125 % 125\% 125% security margin above downstream through-fault. ============================== STEP-BY-STEP SOLUTION ==============================

Step 1: Determine Primary Pickup Current (I_pickup,pri)

Lower limit (Load Security):

I_pu,min = 1.25 * I_load,max = 1.25 * 320 A = 400 A

Upper limit (Fault Sensitivity):

I_pu,max = 0.67 * I_fault,min = 0.67 * 1,800 A = 1,206 A

  • Select primary pickup current: I_pickup,pri = 480 A
  • (Satisfies: 400 A <= 480 A <= 1,206 A)

Secondary Relay Tap Setting:

I_tap,sec = I_pickup,pri / CTR = 480 A / (600 / 5) = 480 / 120 = 4.00 A sec

  • Step 2: Verify Load Security and Fault Sensitivity Ratios
  • Continuous Load Security Margin = 480 A / 320 A = 1.50 (150% of peak load) -> SECURE
  • Sensitivity Multiple at Min Fault = 1,800 A / 480 A = 3.75x pickup -> SENSITIVE (M >= 2.0)
  • Step 3: Compute Multiple of Pickup (M) at Downstream Coordination Fault
  • I_fault,down = 4,200 A
  • M_coord = I_fault,down / I_pickup,pri = 4,200 A / 480 A = 8.750

Step 4: Determine Required Upstream Operating Time and Time Dial (TD)

Target Upstream Time:

t_upstream = t_down + CTI = 0.180 s + 0.250 s = 0.430 s

IEEE Very Inverse Parameters: A = 19.61, B = 0.4910, p = 2.000

Evaluate bracketed term at M = 8.750:

  • M^2 - 1 = (8.750)^2 - 1 = 76.5625 - 1 = 75.5625
  • Term = [ 19.61 / 75.5625 ] + 0.4910 = 0.25952 + 0.4910 = 0.75052

Solve for Time Dial (TD):

  • t_upstream = TD * 0.75052 = 0.430 s
  • TD = 0.430 / 0.75052 = 0.5729

Select practical relay Time Dial setting: TD = 0.58

Verify actual operating time at 4,200 A:

t_actual = 0.58 * 0.75052 = 0.4353 s (Provides CTI = 0.4353 - 0.180 = 0.2553 s >= 0.250 s)

  • Step 5: Compute Relay Operating Time at Maximum Bus Fault (11,500 A)
  • M_max = 11,500 A / 480 A = 23.958
  • M_max^2 - 1 = (23.958)^2 - 1 = 574.00 - 1 = 573.00

Bracketed Term = [ 19.61 / 573.00 ] + 0.4910 = 0.03422 + 0.4910 = 0.52522

Operating Time at 11,500 A (ANSI 51 only):

t_51(11.5 kA) = 0.58 * 0.52522 = 0.3046 s (approx 18.3 cycles at 60 Hz)

  • Step 6: Determine ANSI 50 Instantaneous Overcurrent Pickup Setting
  • Downstream through-fault maximum = 4,200 A
  • Security factor = 125% (1.25)

I_50,pri = 1.25 * I_fault,max,down = 1.25 * 4,200 A = 5,250 A

Secondary Instantaneous Setting:

I_50,sec = 5,250 A / 120 = 43.75 A sec

At the bus fault of 11,500 A, since 11,500 A > 5,250 A, the ANSI 50 element trips

instantaneously with clearing time governed strictly by breaker opening (< 0.050 s / 3 cycles).

  • ===================================================================================
  • 7. Common Exam Traps & Strategic Pitfalls

The Multiple of Pickup Base Mistake: Forgetting that M = I / I p i c k u p M = I / I_{pickup} M = I / I p i c k u p ​ must be computed using matching bases (both in primary amperes or both in secondary amperes). Dividing secondary measured current by primary pickup yields an incorrect value for M M M .

Overlooking CT Saturation at High Fault Currents: Assuming ideal linear transformation when secondary currents exceed 20 × I n o m i n a l 20 \times I_{nominal} 20 × I n o mina l ​ ( 100 A 100\text{ A} 100 A secondary). Severe CT saturation suppresses secondary current, lengthening time-overcurrent operating times and delaying trip commands.

Electromechanical vs. Digital Reset Neglect: Applying an electromechanical relay downstream of a fast reclosing sequence without accounting for disk ratcheting ( t r e s e t t_{reset} t rese t ​ ). If reclose dead time ( 0.3 s 0.3\text{ s} 0.3 s ) is less than reset time ( 15 s 15\text{ s} 15 s ), the relay misoperates on the second shot.

Failing to Translate Voltage Bases Across Transformers: Plotting low-voltage circuit breakers and medium-voltage fuses on the same TCC without scaling by the transformer phase-to-phase voltage ratio ( V p r i / V s e c V_{pri} / V_{sec} V p r i ​ / V sec ​ ).

Loading diagram... ANSI 50/51 Combined Overcurrent Decision Logic