Study guide

14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)

PE Electrical and Computer: Power Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Strategy & Reference Handbook

1.1 PE Power Exam Format, CBT Navigation & Reference Handbook 1.2 2026 Reference Standards (NEC 2020, NFPA 70E-2021, NESC) & Scoring Mechanics 1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery

2 Chapter 2: Measurement, Metering & Field Testing

2.1 Current Transformers (CTs), Potential Transformers (PTs) & Meter Connections 2.2 Instrument Transformer Burdens, Saturation Curves & Ratio Correction Factors 2.3 Insulation Resistance Testing (Megger, Polarization Index, Dielectric Absorption) 2.4 Ground Resistance Testing (Fall-of-Potential 62% Rule & Clamp-on Methods)

3 Chapter 3: General Applications — Grounding & Surge Protection

3.1 Substation Ground Grid Design & IEEE 80 Touch/Step Voltage Criteria 3.2 Lightning Protection Systems & Rolling Sphere / Cone of Protection Methods 3.3 Surge Protective Devices (SPDs) & Voltage Surge Arresters

4 Chapter 4: General Applications — Lighting & Energy Management

4.1 Illumination Engineering & Zonal Cavity / Lumen Method Calculations 4.2 Energy Management, Demand Factors & Load Factor Calculations 4.3 Economic Dispatch, Energy Efficiency & Load Profile Analysis

5 Chapter 5: Electrical Safety & NFPA Standards

5.1 NFPA 70E Shock Protection, Approach Boundaries & PPE Requirements 5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations 5.3 Hazardous (Classified) Locations (Class I, II, III & Division/Zone Systems) 5.4 Special Occupancies & Critical Systems (NEC Articles 517 Health Care, 700/701/702 Emergency)

6 Chapter 6: NEC Wiring Methods & Installation Requirements

6.1 Conductor Ampacity & NEC Table 310.16 Derating Adjustments 6.2 Raceway Fill, Box Sizing & Conduit Bending Calculations (Chapter 9 Tables) 6.3 Equipment Grounding Conductors & Grounding Electrode Sizing (NEC Article 250)

7 Chapter 7: Circuit Analysis — Fundamentals & Symmetrical Components

7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition) 7.2 Balanced Three-Phase Circuits (Wye-Delta Configurations & Power Formulas) 7.3 Symmetrical Components & Fortescue Sequence Transformation Matrices 7.4 Sequence Impedances & Positive, Negative, Zero Sequence Network Construction

8 Chapter 8: Circuit Analysis — Per-Unit & Phasor Analysis

8.1 Per-Unit System Fundamentals & Base Conversion Formulas 8.2 Three-Phase Per-Unit Network Modeling & Equipment Impedance Conversion 8.3 Phasor Diagrams, Complex Power & Power Triangle Relationships

9 Chapter 9: Power Electronics & Logic Controls

9.1 Power Electronic Converters (Rectifiers, Inverters & DC-DC Topologies) 9.2 Inverter-Based Resources (IBRs), Grid-Forming & Grid-Following Controls 9.3 Variable Frequency Drives (VFDs), PWM Operation & Harmonic Mitigation 9.4 Boolean Algebra, Logic Gates, De Morgan's Laws & Ladder Logic Control Diagrams

10 Chapter 10: Rotating Machines — Induction & Synchronous

10.1 Three-Phase Induction Motors (Equivalent Circuits, Slip & Performance) 10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes 10.3 Synchronous Machines (Operating Principles, Power-Angle Curves & V-Curves) 10.4 Motor Starting Methods (DOL, Wye-Delta, Autotransformer, Soft-Start) & Voltage Dip

11 Chapter 11: Electric Power Devices & Renewable Energy

11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation) 11.2 Power Factor Correction Capacitors & Shunt Bank Sizing 11.3 Battery Energy Storage Systems (BESS) & Ultracapacitors 11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)

12 Chapter 12: Transmission & Distribution — Steady-State & Power Quality

12.1 Transmission Line Modeling, Voltage Drop & Conductor Sizing 12.2 Voltage Regulation, Reactive Power Support & Tap-Changer Controls 12.3 Power Quality, Harmonics, THD & IEEE 519 Compliance 12.4 Power Flow Analysis & System Stability (Steady-State, Transient & Swing Equation)

13 Chapter 13: Transmission & Distribution — Fault Analysis & Transformer Shifts

13.1 Symmetrical Three-Phase Bolted Fault Calculations 13.2 Unsymmetrical Fault Analysis (SLG, L-L, DLG Fault Calculations) 13.3 Transformer Connection Types, Zero-Sequence Paths & 30-Degree Phase Shifts

14 Chapter 14: Protection Systems & Device Coordination

14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves 14.2 Protective Relaying Schemes (Differential 87, Distance 21, Undervoltage 27) 14.3 Circuit Breakers, Fuses & Automatic Reclosers 14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)

14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)

Key Takeaways Explain This Topic AI

Selective coordination (NEC Article 100, 240.12, 700.32, 701.27) requires localization of an overcurrent condition to restrict outages strictly to the circuit or equipment immediately faulted, verified from 0.01 s up to maximum available fault current.

The Coordination Time Interval (CTI) defines the vertical time clearance between TCC curves, composed of breaker clearing time ( 0.05 − 0.08 s 0.05-0.08\text{ s} 0.05 − 0.08 s ), relay overtravel ( 0.05 − 0.10 s 0.05-0.10\text{ s} 0.05 − 0.10 s for EM; 0 s 0\text{ s} 0 s for digital), CT saturation margins, and safety buffers, yielding benchmarks of 0.30 − 0.40 s 0.30-0.40\text{ s} 0.30 − 0.40 s for electromechanical and 0.20 − 0.25 s 0.20-0.25\text{ s} 0.20 − 0.25 s for digital relays.

Fuse-to-fuse coordination enforces the 75% rule: the Minimum Melting Time (MMT) of the upstream fuse must not be less than 133% of the downstream fuse's Total Clearing Time (TCT), formulated reciprocally as T C T d o w n s t r e a m ≤ 0.75 × M M T u p s t r e a m TCT_{downstream} \le 0.75 \times MMT_{upstream} TC T d o w n s t re am ​ ≤ 0.75 × MM T u p s t re am ​ .

Breaker-to-breaker selectivity is achieved through time-band separation, intentional short-time delays (STD with I 2 t I^2 t I 2 t in/out), or Zone Selective Interlocking (ZSI) which uses hardwired communication to achieve instantaneous bus protection without sacrificing feeder selectivity.

Transformer protection requires coordinating primary protective curves between the magnetizing inrush point ( 8 − 12 × F L A 8-12 \times FLA 8 − 12 × F L A for 0.1 s 0.1\text{ s} 0.1 s ) and the ANSI/IEEE C57.109 damage curve, shifted by 58% for secondary line-to-ground faults on Delta-Wye systems.

Last updated: August 2026

14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)

Executive Overview: Protection coordination is the systematic engineering process of selecting and calibrating protective devices—relays, circuit breakers, and fuses—so that the device closest to a fault operates first to isolate the faulted section, leaving the remainder of the electrical system undisturbed. On the NCEES PE Power examination, candidates must execute multi-stage coordination studies, calculate precise Coordination Time Intervals ( C T I CTI CT I ), enforce the 75 % 75\% 75% fuse coordination rule, evaluate Zone Selective Interlocking (ZSI), and align curves against equipment thermal damage envelopes (ANSI C57.109 and cable damage).

1. Selective Coordination Mandates & NEC Standards

The National Electrical Code (NEC / NFPA 70) defines Coordination (Selective) in Article 100 as:

"Localization of an overcurrent condition to restrict outages to the circuit or equipment affected, accomplished by the selection and installation of overcurrent protective devices and their ratings or settings for the full range of available overcurrents, from overload to the maximum available fault current, and for the full range of overcurrent protective device operating times associated with those overcurrents (0.01 seconds to infinity)." Selective Coordination vs. Cascading Outage:

Selectively Coordinated System (CORRECT): Non-Selective Cascading System (VIOLATION):

  • Main Breaker [OK - Remains Closed] Main Breaker [TRIPPED! Total Blackout]
  • | |
  • Feeder Breaker [OK - Remains Closed] Feeder Breaker [TRIPPED!]
  • | |
  • Branch Breaker [TRIPPED - Clears Fault] Branch Breaker [TRIPPED]
  • | |
  • [ FAULT ] [ FAULT ]
  • Mandatory NEC Selective Coordination Applications

NEC Article 700.32: Emergency Systems (life safety, egress lighting, exit signs).

NEC Article 701.27: Legally Required Standby Systems (sewage lift pumps, ventilation, communication).

NEC Article 708.54: Critical Operations Power Systems (COPS - homeland security, data centers, 911 centers).

NEC Article 517.26: Essential Electrical Systems in Health Care Facilities.

NEC Article 620.62: Multiple Elevators fed from a single feeder.

2. Coordination Time Interval (CTI) Analytical Budget

The Coordination Time Interval ( C T I CTI CT I ) is the minimum vertical time clearance required between the time-current curves of series-connected protective devices plotted on a log-log TCC. The CTI accounts for physical operating times, component manufacturing tolerances, and relay dynamics: Coordination Time Interval (CTI) Component Stackup:

  • +-----------------------------------------------------------------------------------------+
  • | Upstream Relay Operating Time (t_upstream) |
  • +-----------------------------------------------------------------------------------------+
  • | ^ |
  • | | +---------------------------------------------------------------------------------+ |
  • | | | Safety Buffer / Relay Manufacturing Tolerance Margin (0.05 to 0.10 s) | |
  • | | +---------------------------------------------------------------------------------+ |
  • | CTI | CT Saturation & Transformation Error Margin (0.05 s) | |
  • | | +---------------------------------------------------------------------------------+ |
  • | | | Relay Overtravel / Inertia Coasting Margin (0.05 - 0.10 s for EM; 0.0 s for Digital) | |
  • | | +---------------------------------------------------------------------------------+ |
  • | v | Downstream Circuit Breaker Clearing Time (3-5 cycles = 0.050 - 0.083 s) | |
  • | +---------------------------------------------------------------------------------+ |
  • +-----------------------------------------------------------------------------------------+
  • | Downstream Relay Operating Curve / Breaker Trip Time |
  • +-----------------------------------------------------------------------------------------+
  • CTI Rules of Thumb & Standard Benchmarks

Coordination Pair Standard Benchmark CTI Critical Engineering Rationale

Electromechanical Relay to Electromechanical Relay 0.30 − 0.40 s 0.30 - 0.40\text{ s} 0.30 − 0.40 s Includes breaker clearing ( 0.08 s 0.08\text{ s} 0.08 s ), disk overtravel ( 0.10 s 0.10\text{ s} 0.10 s ), CT errors ( 0.05 s 0.05\text{ s} 0.05 s ), and safety buffer ( 0.10 s 0.10\text{ s} 0.10 s )

Digital (Numerical) Relay to Digital Relay 0.20 − 0.25 s 0.20 - 0.25\text{ s} 0.20 − 0.25 s Eliminates overtravel ( 0.0 s 0.0\text{ s} 0.0 s ); uses precise numerical filtering and faster breaker mechanisms

Digital Relay to Downstream Low-Voltage Breaker 0.15 − 0.20 s 0.15 - 0.20\text{ s} 0.15 − 0.20 s Evaluated between breaker total clearing time and upstream relay curve

Digital Relay to Downstream Power Fuse 0.15 − 0.20 s 0.15 - 0.20\text{ s} 0.15 − 0.20 s Evaluated from downstream fuse Total Clearing Time (TCT) to upstream relay curve

Upstream Fuse to Downstream Digital Relay 0.20 − 0.25 s 0.20 - 0.25\text{ s} 0.20 − 0.25 s Relay curve must sit below upstream fuse Minimum Melting Time (MMT)

  • 3. Classical Coordination Pairing Rules
  • Fuse-to-Fuse Coordination: The 75% Rule

To coordinate two series power fuses, the upstream fuse must not be pre-damaged or weakened while the downstream fuse clears the fault: M M T u p s t r e a m ≥ 1.33 × T C T d o w n s t r e a m ⟺ T C T d o w n s t r e a m ≤ 0.75 × M M T u p s t r e a m MMT_{upstream} \ge 1.33 \times TCT_{downstream} \quad \Longleftrightarrow \quad TCT_{downstream} \le 0.75 \times MMT_{upstream} MM T u p s t re am ​ ≥ 1.33 × TC T d o w n s t re am ​ ⟺ TC T d o w n s t re am ​ ≤ 0.75 × MM T u p s t re am ​

Physical Basis: The 25 % 25\% 25% margin ( 0.75 0.75 0.75 multiplier) accounts for ambient temperature variations, pre-fault load current heating, and manufacturing element tolerances. Fuse-to-Fuse 75% Rule Graphic Envelope:

  • Time (s) ^
  • | Upstream Fuse Minimum Melting Time (MMT_up)
  • | \
  • | \ <- Required Safety Margin: 25% Time Separation
  • | \
  • | \ Downstream Fuse Total Clearing Time (TCT_down)
  • | `--. \
  • | \ \
  • | \ \ (Condition: TCT_down <= 0.75 * MMT_up)
  • +---------------------+------+------------------------------> Current (A)
  • Breaker-to-Breaker Coordination & Zone Selective Interlocking (ZSI)

Time-Band Separation: The top of the downstream breaker trip band must sit below the bottom of the upstream breaker trip band with at least 0.05 − 0.10 s 0.05 - 0.10\text{ s} 0.05 − 0.10 s vertical separation.

Short-Time Delay (STD): The upstream breaker is programmed with a short-time delay ( 0.1 − 0.3 s 0.1 - 0.3\text{ s} 0.1 − 0.3 s ) while the downstream breaker operates instantaneously, providing selectivity up to the upstream breaker's short-time withstand rating.

Zone Selective Interlocking (ZSI): Hardwired digital communication between trip units:

If a fault occurs downstream of Breaker B, Breaker B detects the fault and immediately transmits a Restraint Signal upstream to Main Breaker A.

Main Breaker A receives the restraint signal and shifts to its programmed Short-Time Delay ( 0.30 s 0.30\text{ s} 0.30 s ), allowing Breaker B to clear the fault.

If a fault occurs on the main bus between A and B, Breaker B senses no fault and sends no restraint. Main Breaker A instantly clears the bus fault with zero intentional delay ( < 0.05 s <0.05\text{ s} < 0.05 s ) , combining maximum arc-flash safety with full selectivity.

4. Transformer Inrush & ANSI C57.109 Damage Curves

Protective curves for transformer primary protective devices must satisfy a strict two-sided constraint window : Transformer Protection Operating Window on TCC:

  • Time (s) ^
  • 1000 |
  • 100 | ANSI / IEEE C57.109 Thermal Damage Curve
  • 10 | \
  • 1 | [ Primary \
  • 0.1 | Protective \
  • 0.01 | Device ] \ ANSI C57.109 Mechanical Damage Curve

| | `--.

  • | Inrush -> x (8-12x FLA, 0.1s)
  • +------------+----------+------------------------------------> Current (A)
  • I_FLA I_fault

Inrush Security (Left / Bottom Boundary): The protective curve must remain above and to the right of the transformer inrush points:

Frequent Inrush Point: 8 − 12 × F L A 8 - 12 \times FLA 8 − 12 × F L A for 0.10 s 0.10\text{ s} 0.10 s .

Cold Load Pickup Point: 4 − 6 × F L A 4 - 6 \times FLA 4 − 6 × F L A for 1.0 s 1.0\text{ s} 1.0 s .

Equipment Damage Protection (Right / Top Boundary): The protective curve must lie strictly below and to the left of the ANSI/IEEE C57.109 Damage Curve .

The Delta-Wye Fault Shift Factor: For an unsymmetrical line-to-ground fault on the secondary of a Delta-Wye transformer, the current seen by the primary protective device is reduced relative to a 3-phase fault. To ensure thermal protection, the ANSI damage curve must be shifted to the left by 58 % 58\% 58% ( 1 / 3 = 0.577 1/\sqrt{3} = 0.577 1/ 3 ​ = 0.577 ) : I s h i f t e d = 0.577 × I d a m a g e , 3 ϕ I_{shifted} = 0.577 \times I_{damage,3\phi} I s hi f t e d ​ = 0.577 × I d ama g e , 3 ϕ ​

  • 5. Comprehensive Worked Multi-Stage Coordination Study
  • System Topology

A radial industrial distribution system consists of:

Medium-Voltage Feeder Breaker (CB-1): 13.8 kV 13.8\text{ kV} 13.8 kV , C T R = 600 : 5 CTR = 600:5 CTR = 600 : 5 , digital 51 relay with IEEE Extremely Inverse curve ( A = 28.2 , B = 0.1217 , p = 2.0 A=28.2, B=0.1217, p=2.0 A = 28.2 , B = 0.1217 , p = 2.0 ).

Industrial Substation Transformer (T-1): 2 , 500 kVA 2,500\text{ kVA} 2 , 500 kVA , 13.8 kV / 480 V 13.8\text{ kV} / 480\text{ V} 13.8 kV /480 V , Delta-Wye grounded, Z = 5.75 % Z = 5.75\% Z = 5.75% .

Low-Voltage Main Breaker (CB-2): 480 V 480\text{ V} 480 V , 3 , 200 A 3,200\text{ A} 3 , 200 A LVPCB with electronic trip unit (LSG).

Feeder Breaker (CB-3): 480 V 480\text{ V} 480 V , 800 A 800\text{ A} 800 A frame MCCB with electronic LSI trip unit feeding an MCC.

Branch Breaker (CB-4): 480 V 480\text{ V} 480 V , 100 A 100\text{ A} 100 A thermal-magnetic MCCB.

Maximum 480 V Bus Available Fault Current: I s c , 480 V = 42 , 000 A RMS sym I_{sc,480V} = 42,000\text{ A RMS sym} I sc , 480 V ​ = 42 , 000 A RMS sym .

Maximum Branch Circuit Fault Current: I s c , b r a n c h = 18 , 000 A RMS sym I_{sc,branch} = 18,000\text{ A RMS sym} I sc , b r an c h ​ = 18 , 000 A RMS sym . Multi-Stage Radial Distribution Single-Line Diagram:

  • 13.8 kV Utility / Substation Bus
  • |
  • [ CB-1 ] Relay 51 (IEEE Extremely Inverse, CTR 600:5)
  • |
  • (T-1) 2,500 kVA, 13.8 kV / 480 V, Z = 5.75%
  • |
  • 480 V Main Switchgear Bus (I_sc = 42 kA)
  • |
  • [ CB-2 ] 3,200 A LVPCB (UL 1066 - LSG)
  • |
  • [ CB-3 ] 800 A Feeder Breaker (MCCB - LSI)
  • |
  • 480 V Motor Control Center (I_sc = 18 kA)
  • |
  • [ CB-4 ] 100 A Branch Breaker (Thermal-Mag MCCB)
  • |
  • [ Load ]

Step-by-Step Settings & CTI Calculations ============================== STEP-BY-STEP SOLUTION ==============================

  • Step 1: Compute Transformer Rated Currents and Fault Currents
  • Transformer T-1: 2,500 kVA

Primary FLA (13.8 kV):

I_FLA,pri = 2,500 kVA / (sqrt(3) * 13.8 kV) = 104.59 A pri

Secondary FLA (480 V):

I_FLA,sec = 2,500 kVA / (sqrt(3) * 0.48 kV) = 3,007.0 A sec

Transformer Maximum Secondary Bolted Fault (assuming infinite bus):

  • I_sc,sec = I_FLA,sec / Z_pu = 3,007.0 A / 0.0575 = 52,296 A at 480 V
  • Actual available fault on 480 V bus considering utility source: I_sc,480V = 42,000 A

Referred to 13.8 kV Primary Base:

I_sc,pri = 42,000 A * (480 V / 13,800 V) = 1,460.9 A at 13.8 kV

  • Step 2: Calibrate Branch Breaker CB-4 (100 A Thermal-Mag)
  • Rating = 100 A continuous

Thermal trip band: 100 A to 300 A overload.

Instantaneous magnetic trip: 10x rating = 1,000 A.

At branch fault I_sc = 18,000 A, CB-4 clears instantaneously in t_CB4 = 0.016 s (1 cycle).

  • Step 3: Calibrate Feeder Breaker CB-3 (800 A Frame MCCB)
  • Continuous rating plug: I_n = 800 A
  • Long-Time Setting: I_r = 1.0 * 800 A = 800 A, Delay t_r = 10 s at 6*I_r
  • Short-Time Pickup: I_sd = 4.0 * 800 A = 3,200 A (Above motor inrush)
  • Short-Time Delay: Set to t_sd = 0.10 s (Flat delay)
  • Instantaneous (I): OFF (enabled via Zone Selective Interlocking)

Verification at Branch Fault (18,000 A):

CB-4 clears in 0.016 s.

CB-3 waits for its 0.10 s short-time delay.

Clearance Margin = 0.10 s - 0.016 s = 0.084 s (SELECTIVE! CB-4 isolates fault).

  • Step 4: Calibrate 480 V Main Breaker CB-2 (3,200 A LVPCB)
  • Continuous rating plug: I_n = 3,200 A
  • Long-Time Setting: I_r = 1.0 * 3,200 A = 3,200 A
  • Short-Time Pickup: I_sd = 2.5 * 3,200 A = 8,000 A
  • Short-Time Delay: Set to t_sd = 0.25 s (Coordinates with CB-3 at 0.10 s)

CTI between CB-3 and CB-2:

CTI = t_sd,CB2 - t_sd,CB3 = 0.25 s - 0.10 s = 0.150 s (Meets LVPCB CTI benchmark).

  • Step 5: Calibrate 13.8 kV Primary Relay 51 (CB-1)
  • CT Ratio: 600:5 (CTR = 120)
  • Primary Full-Load Current = 104.59 A
  • Select Relay Pickup: I_pickup,pri = 1.50 * 104.59 A = 156.88 A -> Set I_pu = 160 A pri
  • Secondary Tap Setting: I_tap = 160 A / 120 = 1.33 A sec

Target Operating Time at Maximum 480 V Bus Fault (42,000 A sec / 1,460.9 A pri):

  • Downstream CB-2 clears in t_CB2 = 0.25 s + 0.05 s breaker open = 0.30 s
  • Required CTI for digital relay = 0.20 s
  • Target Relay Time: t_relay = 0.30 s + 0.20 s = 0.50 s

Calculate Multiple of Pickup M at 1,460.9 A pri:

  • M = 1,460.9 A / 160 A = 9.1306
  • M^2 - 1 = (9.1306)^2 - 1 = 83.368 - 1 = 82.368

IEEE Extremely Inverse Bracketed Term:

Term = [ 28.2 / 82.368 ] + 0.1217 = 0.34236 + 0.1217 = 0.46406

Solve for Time Dial TD:

  • t_relay = TD * 0.46406 = 0.50 s
  • TD = 0.50 / 0.46406 = 1.077 -> Select TD = 1.10

Actual Relay Operating Time at 1,460.9 A:

t_actual = 1.10 * 0.46406 = 0.5105 s

Achieved CTI = 0.5105 s - 0.300 s = 0.2105 s >= 0.200 s (COORDINATION VERIFIED!).

  • Step 6: Check Transformer Inrush and Damage Withstand Envelopes
  • 1. Inrush Check: 10x FLA = 1,046 A at 0.10 s
  • At 1,046 A: M = 1,046 / 160 = 6.5375 -> M^2 - 1 = 41.738
  • t_inrush_trip = 1.10 * [ 28.2 / 41.738 + 0.1217 ] = 1.10 * [ 0.6756 + 0.1217 ] = 0.877 s

Since 0.877 s >> 0.10 s inrush duration, the relay WILL NOT FALSE TRIP on inrush.

2. Damage Curve Check: Transformer thermal damage limit at 1,460.9 A (14x FLA) is 8.0 s.

Relay operates in 0.51 s << 8.0 s (Transformer FULLY PROTECTED).

  • ===================================================================================
  • 6. Common Exam Traps & Strategic Pitfalls

The Zero-Crossing / 0.01 Second NEC Coordination Trap: Assuming selective coordination only applies to time delays > 0.1 s >0.1\text{ s} > 0.1 s . NEC Articles 700 and 708 explicitly require coordination down to 0.01 seconds 0.01\text{ seconds} 0.01 seconds ( 0.6 cycles 0.6\text{ cycles} 0.6 cycles ), meaning instantaneous trip curves cannot overlap under any circumstances.

Inverting the 75% Fuse Coordination Rule: Multiplying the downstream fuse TCT by 1.33 1.33 1.33 instead of verifying that T C T d o w n s t r e a m ≤ 0.75 × M M T u p s t r e a m TCT_{downstream} \le 0.75 \times MMT_{upstream} TC T d o w n s t re am ​ ≤ 0.75 × MM T u p s t re am ​ .

Neglecting Delta-Wye Shift on Transformer Damage Curves: Forgetting to shift the ANSI C57.109 transformer thermal damage curve by 58 % 58\% 58% to the left when evaluating secondary line-to-ground fault protection.

Ignoring Breaker Mechanism Clearing Times in CTI Budgets: Setting the relay time delay equal to the downstream breaker short-time delay without adding the breaker's physical contact parting and arc extinguishing time ( 3 − 5 cycles = 0.05 − 0.08 s 3-5\text{ cycles} = 0.05-0.08\text{ s} 3 − 5 cycles = 0.05 − 0.08 s ).

Loading diagram... Zone Selective Interlocking (ZSI) Fast Fault Discrimination