Study guide
10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes
PE Electrical and Computer: Power Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Strategy & Reference Handbook
1.1 PE Power Exam Format, CBT Navigation & Reference Handbook 1.2 2026 Reference Standards (NEC 2020, NFPA 70E-2021, NESC) & Scoring Mechanics 1.3 CBT Pacing, AIT Question Formats & Formula Sheet Mastery
2 Chapter 2: Measurement, Metering & Field Testing
2.1 Current Transformers (CTs), Potential Transformers (PTs) & Meter Connections 2.2 Instrument Transformer Burdens, Saturation Curves & Ratio Correction Factors 2.3 Insulation Resistance Testing (Megger, Polarization Index, Dielectric Absorption) 2.4 Ground Resistance Testing (Fall-of-Potential 62% Rule & Clamp-on Methods)
3 Chapter 3: General Applications — Grounding & Surge Protection
3.1 Substation Ground Grid Design & IEEE 80 Touch/Step Voltage Criteria 3.2 Lightning Protection Systems & Rolling Sphere / Cone of Protection Methods 3.3 Surge Protective Devices (SPDs) & Voltage Surge Arresters
4 Chapter 4: General Applications — Lighting & Energy Management
4.1 Illumination Engineering & Zonal Cavity / Lumen Method Calculations 4.2 Energy Management, Demand Factors & Load Factor Calculations 4.3 Economic Dispatch, Energy Efficiency & Load Profile Analysis
5 Chapter 5: Electrical Safety & NFPA Standards
5.1 NFPA 70E Shock Protection, Approach Boundaries & PPE Requirements 5.2 Arc-Flash Hazard Analysis & IEEE 1584-2018 Incident Energy Calculations 5.3 Hazardous (Classified) Locations (Class I, II, III & Division/Zone Systems) 5.4 Special Occupancies & Critical Systems (NEC Articles 517 Health Care, 700/701/702 Emergency)
6 Chapter 6: NEC Wiring Methods & Installation Requirements
6.1 Conductor Ampacity & NEC Table 310.16 Derating Adjustments 6.2 Raceway Fill, Box Sizing & Conduit Bending Calculations (Chapter 9 Tables) 6.3 Equipment Grounding Conductors & Grounding Electrode Sizing (NEC Article 250)
7 Chapter 7: Circuit Analysis — Fundamentals & Symmetrical Components
7.1 DC & Single-Phase AC Network Analysis (Thevenin, Norton, Superposition) 7.2 Balanced Three-Phase Circuits (Wye-Delta Configurations & Power Formulas) 7.3 Symmetrical Components & Fortescue Sequence Transformation Matrices 7.4 Sequence Impedances & Positive, Negative, Zero Sequence Network Construction
8 Chapter 8: Circuit Analysis — Per-Unit & Phasor Analysis
8.1 Per-Unit System Fundamentals & Base Conversion Formulas 8.2 Three-Phase Per-Unit Network Modeling & Equipment Impedance Conversion 8.3 Phasor Diagrams, Complex Power & Power Triangle Relationships
9 Chapter 9: Power Electronics & Logic Controls
9.1 Power Electronic Converters (Rectifiers, Inverters & DC-DC Topologies) 9.2 Inverter-Based Resources (IBRs), Grid-Forming & Grid-Following Controls 9.3 Variable Frequency Drives (VFDs), PWM Operation & Harmonic Mitigation 9.4 Boolean Algebra, Logic Gates, De Morgan's Laws & Ladder Logic Control Diagrams
10 Chapter 10: Rotating Machines — Induction & Synchronous
10.1 Three-Phase Induction Motors (Equivalent Circuits, Slip & Performance) 10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes 10.3 Synchronous Machines (Operating Principles, Power-Angle Curves & V-Curves) 10.4 Motor Starting Methods (DOL, Wye-Delta, Autotransformer, Soft-Start) & Voltage Dip
11 Chapter 11: Electric Power Devices & Renewable Energy
11.1 Power Transformers (Equivalent Circuits, Efficiency & Voltage Regulation) 11.2 Power Factor Correction Capacitors & Shunt Bank Sizing 11.3 Battery Energy Storage Systems (BESS) & Ultracapacitors 11.4 Renewable Energy Generation (Solar Photovoltaic Systems & Wind Turbines)
12 Chapter 12: Transmission & Distribution — Steady-State & Power Quality
12.1 Transmission Line Modeling, Voltage Drop & Conductor Sizing 12.2 Voltage Regulation, Reactive Power Support & Tap-Changer Controls 12.3 Power Quality, Harmonics, THD & IEEE 519 Compliance 12.4 Power Flow Analysis & System Stability (Steady-State, Transient & Swing Equation)
13 Chapter 13: Transmission & Distribution — Fault Analysis & Transformer Shifts
13.1 Symmetrical Three-Phase Bolted Fault Calculations 13.2 Unsymmetrical Fault Analysis (SLG, L-L, DLG Fault Calculations) 13.3 Transformer Connection Types, Zero-Sequence Paths & 30-Degree Phase Shifts
14 Chapter 14: Protection Systems & Device Coordination
14.1 Overcurrent Protection & Time-Current Characteristic (TCC) Curves 14.2 Protective Relaying Schemes (Differential 87, Distance 21, Undervoltage 27) 14.3 Circuit Breakers, Fuses & Automatic Reclosers 14.4 Protection Coordination, Selectivity & Coordination Time Intervals (CTI)
10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes
Key Takeaways Explain This Topic AI
The developed torque equation derived from the stator Thevenin circuit demonstrates that torque is proportional to the square of applied terminal voltage ( T d e v ∝ V t h 2 T_{dev} \propto V_{th}^2 T d e v ∝ V t h 2 ).
Maximum (breakdown) torque T m a x T_{max} T ma x is independent of rotor resistance R 2 ′ R_2' R 2 ′ , but the slip at which breakdown occurs ( s m a x , T s_{max,T} s ma x , T ) is directly proportional to R 2 ′ R_2' R 2 ′ .
NEMA Design Classes A, B, C, and D define standardized starting torque, locked-rotor inrush current, and full-load slip profiles tailored to specific industrial load types.
Wound-Rotor Induction Motors (WRIM) utilize external rotor resistance inserted via slip rings to shift maximum breakdown torque directly to starting ( s m a x , T = 1.0 s_{max,T} = 1.0 s ma x , T = 1.0 ) while minimizing starting inrush current.
Deep-bar and double-cage rotor constructions exploit frequency-dependent AC skin effect during starting ( f r = 60 Hz f_r = 60\text{ Hz} f r = 60 Hz ) to achieve high starting resistance and low running resistance.
Last updated: August 2026
10.2 Induction Motor Torque-Speed Characteristics & NEMA Design Classes
The torque-speed profile of a three-phase induction motor governs how it accelerates connected mechanical loads from standstill to rated operating speed. On the PE Power exam, questions frequently test your ability to calculate developed torque, determine maximum (breakdown) torque and pull-out slip, analyze voltage-sag impacts on available torque, and select appropriate NEMA Design Classes for specific industrial duty cycles.
1. Torque-Speed Equation and Analytical Derivation
Using the per-phase Thevenin equivalent circuit of the induction motor ( V t h , R t h , X t h V_{th}, R_{th}, X_{th} V t h , R t h , X t h ), the magnitude of the rotor current referred to the stator is: I 2 ′ = V t h ( R t h + R 2 ′ s ) 2 + ( X t h + X 2 ′ ) 2 I_2' = \frac{V_{th}}{\sqrt{\left(R_{th} + \frac{R_2'}{s}\right)^2 + (X_{th} + X_2')^2}} I 2 ′ = ( R t h + s R 2 ′ ) 2 + ( X t h + X 2 ′ ) 2 V t h
Recalling that developed torque is T d e v = P a g ω s = 3 ( I 2 ′ ) 2 ( R 2 ′ / s ) ω s T_{dev} = \frac{P_{ag}}{\omega_s} = \frac{3 (I_2')^2 (R_2'/s)}{\omega_s} T d e v = ω s P a g = ω s 3 ( I 2 ′ ) 2 ( R 2 ′ / s ) , substituting I 2 ′ I_2' I 2 ′ yields the fundamental induction motor torque equation : T d e v = 3 V t h 2 ( R 2 ′ s ) ω s [ ( R t h + R 2 ′ s ) 2 + ( X t h + X 2 ′ ) 2 ] [ N ⋅ m ] T_{dev} = \frac{3 V_{th}^2 \left(\frac{R_2'}{s}\right)}{\omega_s \left[ \left( R_{th} + \frac{R_2'}{s} \right)^2 + (X_{th} + X_2')^2 \right]} \quad [\text{N}\cdot\text{m}] T d e v = ω s [ ( R t h + s R 2 ′ ) 2 + ( X t h + X 2 ′ ) 2 ] 3 V t h 2 ( s R 2 ′ ) [ N ⋅ m ]
Asymptotic Behavior Across the Speed Curve
Low Slip / Normal Operating Region ( s ≈ 0 s \approx 0 s ≈ 0 to 0.05 0.05 0.05 ) :
When slip is very small, R 2 ′ s ≫ R t h \frac{R_2'}{s} \gg R_{th} s R 2 ′ ≫ R t h and R 2 ′ s ≫ ( X t h + X 2 ′ ) \frac{R_2'}{s} \gg (X_{th} + X_2') s R 2 ′ ≫ ( X t h + X 2 ′ ) . The torque equation simplifies to: T d e v ≈ 3 V t h 2 s ω s R 2 ′ T_{dev} \approx \frac{3 V_{th}^2 s}{\omega_s R_2'} T d e v ≈ ω s R 2 ′ 3 V t h 2 s
In this linear operating region, developed torque is directly proportional to slip and inversely proportional to rotor resistance R 2 ′ R_2' R 2 ′ .
High Slip / Starting Region ( s ≈ 0.5 s \approx 0.5 s ≈ 0.5 to 1.0 1.0 1.0 ) :
At high slip, ( X t h + X 2 ′ ) 2 ≫ ( R t h + R 2 ′ s ) 2 (X_{th} + X_2')^2 \gg \left( R_{th} + \frac{R_2'}{s} \right)^2 ( X t h + X 2 ′ ) 2 ≫ ( R t h + s R 2 ′ ) 2 . The torque equation simplifies to: T d e v ≈ 3 V t h 2 R 2 ′ ω s s ( X t h + X 2 ′ ) 2 T_{dev} \approx \frac{3 V_{th}^2 R_2'}{\omega_s s (X_{th} + X_2')^2} T d e v ≈ ω s s ( X t h + X 2 ′ ) 2 3 V t h 2 R 2 ′
In this region, developed torque is inversely proportional to slip and directly proportional to rotor resistance R 2 ′ R_2' R 2 ′ .
Locked-Rotor (Starting) Torque ( s = 1.0 s = 1.0 s = 1.0 ) : T s t a r t = 3 V t h 2 R 2 ′ ω s [ ( R t h + R 2 ′ ) 2 + ( X t h + X 2 ′ ) 2 ] T_{start} = \frac{3 V_{th}^2 R_2'}{\omega_s \left[ (R_{th} + R_2')^2 + (X_{th} + X_2')^2 \right]} T s t a r t = ω s [ ( R t h + R 2 ′ ) 2 + ( X t h + X 2 ′ ) 2 ] 3 V t h 2 R 2 ′
2. Maximum (Breakdown) Torque and Slip at Breakdown
By applying the Maximum Power Transfer theorem to the rotor branch in the Thevenin equivalent circuit, maximum power transfer across the air gap (and therefore maximum developed torque) occurs when the load resistance R 2 ′ s \frac{R_2'}{s} s R 2 ′ equals the magnitude of the source impedance seen by the rotor: R 2 ′ s m a x , T = R t h 2 + ( X t h + X 2 ′ ) 2 \frac{R_2'}{s_{max,T}} = \sqrt{R_{th}^2 + (X_{th} + X_2')^2} s ma x , T R 2 ′ = R t h 2 + ( X t h + X 2 ′ ) 2
Solving for the slip at maximum torque ( s m a x , T s_{max,T} s ma x , T or s p o s_{po} s p o , pull-out slip): s m a x , T = R 2 ′ R t h 2 + ( X t h + X 2 ′ ) 2 ≈ R 2 ′ X t h + X 2 ′ s_{max,T} = \frac{R_2'}{\sqrt{R_{th}^2 + (X_{th} + X_2')^2}} \approx \frac{R_2'}{X_{th} + X_2'} s ma x , T = R t h 2 + ( X t h + X 2 ′ ) 2 R 2 ′ ≈ X t h + X 2 ′ R 2 ′
Substituting s m a x , T s_{max,T} s ma x , T back into the general torque equation yields the maximum (breakdown) torque ( T m a x T_{max} T ma x or T p o T_{po} T p o ): T m a x = 3 V t h 2 2 ω s [ R t h + R t h 2 + ( X t h + X 2 ′ ) 2 ] ≈ 3 V t h 2 2 ω s ( X t h + X 2 ′ ) T_{max} = \frac{3 V_{th}^2}{2 \omega_s \left[ R_{th} + \sqrt{R_{th}^2 + (X_{th} + X_2')^2} \right]} \approx \frac{3 V_{th}^2}{2 \omega_s (X_{th} + X_2')} T ma x = 2 ω s [ R t h + R t h 2 + ( X t h + X 2 ′ ) 2 ] 3 V t h 2 ≈ 2 ω s ( X t h + X 2 ′ ) 3 V t h 2
Critical Invariants of Breakdown Torque
Independence of R 2 ′ R_2' R 2 ′ : Maximum breakdown torque T m a x T_{max} T ma x is completely independent of rotor resistance R 2 ′ R_2' R 2 ′ . Changing rotor resistance does not alter the peak torque magnitude; it only shifts the speed (slip s m a x , T s_{max,T} s ma x , T ) at which peak torque occurs.
Proportionality of s m a x , T s_{max,T} s ma x , T to R 2 ′ R_2' R 2 ′ : The slip at breakdown is directly proportional to R 2 ′ R_2' R 2 ′ . Increasing rotor resistance shifts the breakdown torque peak toward lower speeds (higher slip).
Voltage Sensitivity : Both starting torque and breakdown torque are proportional to the square of terminal voltage ( T ∝ V 2 T \propto V^2 T ∝ V 2 ). A 10 % 10\% 10% voltage drop reduces available breakdown torque by ( 0.90 ) 2 = 0.81 (0.90)^2 = 0.81 ( 0.90 ) 2 = 0.81 ( 19 % 19\% 19% reduction).
3. NEMA Design Classes (A, B, C, D) per NEMA MG 1
NEMA standard MG 1 categorizes squirrel-cage induction motors into four standardized design classes based on starting torque, starting current (locked-rotor inrush), slip, and rotor cage geometry.
Deep-Bar and Double-Cage Rotor Physics
Squirrel-cage rotor bars exploit the AC skin effect during starting:
At start ( s = 1.0 , f r = 60 Hz s = 1.0, f_r = 60\text{ Hz} s = 1.0 , f r = 60 Hz ) : High rotor frequency forces rotor current toward the top of the slot (outer cage), where leakage reactance is low. This restricts current flow to a small cross-sectional area, yielding high effective resistance ( R 2 ′ R_2' R 2 ′ ) for high starting torque and low inrush current.
At rated speed ( s ≈ 0.03 , f r ≈ 1.8 Hz s \approx 0.03, f_r \approx 1.8\text{ Hz} s ≈ 0.03 , f r ≈ 1.8 Hz ) : Very low rotor frequency allows current to distribute evenly throughout the entire slot depth (inner cage), lowering effective resistance ( R 2 ′ R_2' R 2 ′ ) to ensure low slip, high operating efficiency, and low full-load heating.
NEMA Design Class Comparison Table
NEMA Class Starting Torque (% Rated) Starting Current (% Rated) Breakdown Torque (% Rated) Full-Load Slip ( s s s ) Rotor Slot Design Typical Industrial Applications
Design A Normal ( 150 − 170 % 150 - 170\% 150 − 170% ) High ( 600 − 800 % + 600 - 800\%+ 600 − 800% + ) High ( 200 − 250 % 200 - 250\% 200 − 250% ) Low ( < 5 % < 5\% < 5% ) Standard shallow bars Machine tools, fans, blowers where starting inrush is not restricted by utility.
Design B Normal ( 150 − 160 % 150 - 160\% 150 − 160% ) Normal ( 500 − 600 % 500 - 600\% 500 − 600% ) Normal ( 200 − 220 % 200 - 220\% 200 − 220% ) Low ( < 5 % < 5\% < 5% ) Deep-bar rotor (general purpose workhorse) Centrifugal pumps, fans, compressors, conveyors ( most common industrial motor, > 85 % >85\% > 85% of installations ).
Design C High ( 200 − 250 % 200 - 250\% 200 − 250% ) Normal ( 500 − 600 % 500 - 600\% 500 − 600% ) Normal ( 190 − 225 % 190 - 225\% 190 − 225% ) Low ( < 5 % < 5\% < 5% ) Double-cage rotor (high-R outer cage, low-R inner cage) High breakaway torque loads starting under load: loaded conveyors, crushers, reciprocating pumps, pulverizers.
Design D Very High ( 275 − 300 % + 275 - 300\%+ 275 − 300% + ) Low ( 400 − 500 % 400 - 500\% 400 − 500% ) No peak (maximum torque at s = 1.0 s=1.0 s = 1.0 ) High ( 5 − 13 % + 5 - 13\%+ 5 − 13% + ) High-resistance brass/alloy bars High-inertia cyclic loads: punch presses, shears, cranes, hoists, oil well pump jacks (uses high slip to harness flywheel kinetic energy).
4. Wound-Rotor Induction Motors (WRIM)
In a Wound-Rotor Induction Motor (WRIM) , the rotor has a standard balanced 3-phase winding connected to three insulated slip rings on the shaft. External variable resistors ( R e x t R_{ext} R e x t ) are connected to the slip rings via stationary carbon brushes.
External Resistance Insertion
The total effective rotor resistance referred to the stator becomes: R 2 , t o t a l ′ = R 2 ′ + R e x t ′ R_{2,total}' = R_2' + R_{ext}' R 2 , t o t a l ′ = R 2 ′ + R e x t ′
By adjusting R e x t ′ R_{ext}' R e x t ′ , engineers can arbitrarily position the slip at maximum breakdown torque ( s m a x , T s_{max,T} s ma x , T ) anywhere between running slip and locked rotor ( s = 1.0 s = 1.0 s = 1.0 ): s m a x , T = R 2 ′ + R e x t ′ R t h 2 + ( X t h + X 2 ′ ) 2 s_{max,T} = \frac{R_2' + R_{ext}'}{\sqrt{R_{th}^2 + (X_{th} + X_2')^2}} s ma x , T = R t h 2 + ( X t h + X 2 ′ ) 2 R 2 ′ + R e x t ′
To achieve maximum possible starting torque ( T s t a r t = T m a x T_{start} = T_{max} T s t a r t = T ma x ) at standstill ( s = 1.0 s = 1.0 s = 1.0 ), external resistance is chosen such that: R e x t ′ = R t h 2 + ( X t h + X 2 ′ ) 2 − R 2 ′ R_{ext}' = \sqrt{R_{th}^2 + (X_{th} + X_2')^2} - R_2' R e x t ′ = R t h 2 + ( X t h + X 2 ′ ) 2 − R 2 ′
As the motor accelerates, R e x t R_{ext} R e x t is progressively stepped down (often via contactor timing relays) to maintain high acceleration torque and low slip, until the slip rings are completely short-circuited at rated speed for maximum operating efficiency.
- 5. Worked Numeric Example: Breakdown Torque and Rotor Resistance Design
- Problem Statement
A 460 V (line-to-line, rms), 60 Hz, 4-pole, Y-connected wound-rotor induction motor has Thevenin equivalent parameters:
- V t h = 254.0 V V_{th} = 254.0\text{ V} V t h = 254.0 V
- R t h = 0.20 Ω R_{th} = 0.20\,\Omega R t h = 0.20 Ω
- X t h = 0.50 Ω X_{th} = 0.50\,\Omega X t h = 0.50 Ω
- Rotor leakage reactance: X 2 ′ = 0.50 Ω X_2' = 0.50\,\Omega X 2 ′ = 0.50 Ω
- Internal rotor winding resistance: R 2 ′ = 0.15 Ω R_2' = 0.15\,\Omega R 2 ′ = 0.15 Ω
Calculate:
Synchronous speed ω s \omega_s ω s in rad/s.
The slip at maximum torque ( s m a x , T s_{max,T} s ma x , T ) and the corresponding rotor speed ( n m a x , T n_{max,T} n ma x , T in rpm) under unmodified conditions.
The maximum breakdown torque ( T m a x T_{max} T ma x ) in N ⋅ m \text{N}\cdot\text{m} N ⋅ m .
The starting torque ( T s t a r t T_{start} T s t a r t ) at s = 1.0 s = 1.0 s = 1.0 without external resistance.
The external resistance R e x t ′ R_{ext}' R e x t ′ (referred to stator) that must be added per phase to produce maximum breakdown torque directly at starting ( s = 1.0 s = 1.0 s = 1.0 ).
Step-by-Step Solution
Step 1: Synchronous Angular Speed n s = 120 × 60 4 = 1 , 800 rpm n_s = \frac{120 \times 60}{4} = 1,800\text{ rpm} n s = 4 120 × 60 = 1 , 800 rpm ω s = 2 π × 1 , 800 60 = 188.496 rad/s \omega_s = \frac{2\pi \times 1,800}{60} = 188.496\text{ rad/s} ω s = 60 2 π × 1 , 800 = 188.496 rad/s
Step 2: Unmodified Slip at Maximum Torque and Rotor Speed s m a x , T = R 2 ′ R t h 2 + ( X t h + X 2 ′ ) 2 = 0.15 ( 0.20 ) 2 + ( 0.50 + 0.50 ) 2 = 0.15 0.04 + 1.00 = 0.15 1.04 = 0.15 1.0198 = 0.1471 ( 14.71 % slip ) s_{max,T} = \frac{R_2'}{\sqrt{R_{th}^2 + (X_{th} + X_2')^2}} = \frac{0.15}{\sqrt{(0.20)^2 + (0.50 + 0.50)^2}} = \frac{0.15}{\sqrt{0.04 + 1.00}} = \frac{0.15}{\sqrt{1.04}} = \frac{0.15}{1.0198} = 0.1471 \quad (14.71\%\text{ slip}) s ma x , T = R t h 2 + ( X t h + X 2 ′ ) 2 R 2 ′ = ( 0.20 ) 2 + ( 0.50 + 0.50 ) 2 0.15 = 0.04 + 1.00 0.15 = 1.04 0.15 = 1.0198 0.15 = 0.1471 ( 14.71% slip )
Rotor breakdown speed: n m a x , T = n s ( 1 − s m a x , T ) = 1 , 800 × ( 1 − 0.1471 ) = 1 , 800 × 0.8529 = 1 , 535.2 rpm n_{max,T} = n_s (1 - s_{max,T}) = 1,800 \times (1 - 0.1471) = 1,800 \times 0.8529 = 1,535.2\text{ rpm} n ma x , T = n s ( 1 − s ma x , T ) = 1 , 800 × ( 1 − 0.1471 ) = 1 , 800 × 0.8529 = 1 , 535.2 rpm
Step 3: Maximum Breakdown Torque T m a x = 3 V t h 2 2 ω s [ R t h + R t h 2 + ( X t h + X 2 ′ ) 2 ] = 3 × ( 254.0 ) 2 2 × 188.496 [ 0.20 + 1.0198 ] = 3 × 64 , 516 376.992 × 1.2198 = 193 , 548 459.855 = 420.89 N ⋅ m T_{max} = \frac{3 V_{th}^2}{2 \omega_s \left[ R_{th} + \sqrt{R_{th}^2 + (X_{th} + X_2')^2} \right]} = \frac{3 \times (254.0)^2}{2 \times 188.496 \left[ 0.20 + 1.0198 \right]} = \frac{3 \times 64,516}{376.992 \times 1.2198} = \frac{193,548}{459.855} = 420.89\text{ N}\cdot\text{m} T ma x = 2 ω s [ R t h + R t h 2 + ( X t h + X 2 ′ ) 2 ] 3 V t h 2 = 2 × 188.496 [ 0.20 + 1.0198 ] 3 × ( 254.0 ) 2 = 376.992 × 1.2198 3 × 64 , 516 = 459.855 193 , 548 = 420.89 N ⋅ m
Step 4: Starting Torque Without External Resistance ( s = 1.0 s = 1.0 s = 1.0 ) T s t a r t = 3 V t h 2 R 2 ′ ω s [ ( R t h + R 2 ′ ) 2 + ( X t h + X 2 ′ ) 2 ] = 3 × ( 254.0 ) 2 × 0.15 188.496 [ ( 0.20 + 0.15 ) 2 + ( 0.50 + 0.50 ) 2 ] = 29 , 032.2 188.496 [ ( 0.35 ) 2 + ( 1.00 ) 2 ] = 29 , 032.2 188.496 × ( 0.1225 + 1.00 ) = 29 , 032.2 188.496 × 1.1225 = 29 , 032.2 211.587 = 137.21 N ⋅ m T_{start} = \frac{3 V_{th}^2 R_2'}{\omega_s \left[ (R_{th} + R_2')^2 + (X_{th} + X_2')^2 \right]} = \frac{3 \times (254.0)^2 \times 0.15}{188.496 \left[ (0.20 + 0.15)^2 + (0.50 + 0.50)^2 \right]} = \frac{29,032.2}{188.496 \left[ (0.35)^2 + (1.00)^2 \right]} = \frac{29,032.2}{188.496 \times (0.1225 + 1.00)} = \frac{29,032.2}{188.496 \times 1.1225} = \frac{29,032.2}{211.587} = 137.21\text{ N}\cdot\text{m} T s t a r t = ω s [ ( R t h + R 2 ′ ) 2 + ( X t h + X 2 ′ ) 2 ] 3 V t h 2 R 2 ′ = 188.496 [ ( 0.20 + 0.15 ) 2 + ( 0.50 + 0.50 ) 2 ] 3 × ( 254.0 ) 2 × 0.15 = 188.496 [ ( 0.35 ) 2 + ( 1.00 ) 2 ] 29 , 032.2 = 188.496 × ( 0.1225 + 1.00 ) 29 , 032.2 = 188.496 × 1.1225 29 , 032.2 = 211.587 29 , 032.2 = 137.21 N ⋅ m
(Notice that starting torque is only 137.21 / 420.89 = 32.6 % 137.21 / 420.89 = 32.6\% 137.21/420.89 = 32.6% of breakdown torque).
Step 5: External Resistance for Maximum Starting Torque
For s m a x , T = 1.0 s_{max,T} = 1.0 s ma x , T = 1.0 : R 2 ′ + R e x t ′ s m a x , T = R t h 2 + ( X t h + X 2 ′ ) 2 \frac{R_2' + R_{ext}'}{s_{max,T}} = \sqrt{R_{th}^2 + (X_{th} + X_2')^2} s ma x , T R 2 ′ + R e x t ′ = R t h 2 + ( X t h + X 2 ′ ) 2 R 2 ′ + R e x t ′ = 1.0 × 1.0198 = 1.0198 Ω R_2' + R_{ext}' = 1.0 \times 1.0198 = 1.0198\,\Omega R 2 ′ + R e x t ′ = 1.0 × 1.0198 = 1.0198 Ω R e x t ′ = 1.0198 − R 2 ′ = 1.0198 − 0.15 = 0.8698 Ω R_{ext}' = 1.0198 - R_2' = 1.0198 - 0.15 = 0.8698\,\Omega R e x t ′ = 1.0198 − R 2 ′ = 1.0198 − 0.15 = 0.8698 Ω
Adding R e x t ′ = 0.87 Ω R_{ext}' = 0.87\,\Omega R e x t ′ = 0.87 Ω per phase increases starting torque from 137.2 N ⋅ m 137.2\text{ N}\cdot\text{m} 137.2 N ⋅ m up to the full breakdown torque of 420.9 N ⋅ m 420.9\text{ N}\cdot\text{m} 420.9 N ⋅ m ( 306 % 306\% 306% increase) while significantly reducing starting inrush current.
6. Common Exam Traps & High-Yield Summary
Warning
Exam Trap 1: Assuming Added Rotor Resistance Increases T m a x T_{max} T ma x Adding external resistance to a wound rotor or choosing a high-resistance rotor alloy (Class D) does NOT increase peak breakdown torque . It only shifts the slip at which breakdown occurs ( s m a x , T ∝ R 2 ′ s_{max,T} \propto R_2' s ma x , T ∝ R 2 ′ ).
Warning
Exam Trap 2: Neglecting Voltage-Squared Proportionality If bus voltage drops by 10 % 10\% 10% during starting ( V = 0.90 V n V = 0.90 V_n V = 0.90 V n ), both starting torque and breakdown torque decrease by ( 0.90 ) 2 = 0.81 (0.90)^2 = 0.81 ( 0.90 ) 2 = 0.81 ( 19 % 19\% 19% reduction), NOT by 10 % 10\% 10% .
- Important
- Exam Trap 3: Distinguishing NEMA C vs NEMA D Applications
Choose NEMA C for loads that require high breakaway torque to start, but run continuously at high efficiency with low slip (e.g., loaded conveyors, crushers, slurry pumps).
Choose NEMA D for high-inertia cyclic/impact loads where high running slip is deliberately required to allow a mechanical flywheel to release stored kinetic energy during peak stroke (e.g., punch presses, shears).