Study guide

9.4 Double Line-to-Ground (DLG) Faults & Bus Impedance Matrix (Zbus) Methods

PE Electrical and Computer Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview & Power Engineering Fundamentals

1.1 PE Power Exam Structure, Official Specification & NCEES Reference Strategy 1.2 Units, Conversions, Engineering Constants & Fundamental Power Equations 1.3 Measurement & Metering Principles (Power, Energy, Power Factor) 1.4 Instrument Testing & Diagnostics (Insulation Megger & Ground Resistance)

2 Chapter 2: Circuit Analysis Fundamentals

2.1 DC Circuit Laws, Network Theorems (Thevenin, Norton, Superposition) & Transients 2.2 Single-Phase AC Steady-State Analysis, Phasors & Impedance 2.3 AC Power Relationships (Real, Reactive, Apparent Power & Power Factor Correction) 2.4 Resonance, Frequency Response & Harmonic Distortion

3 Chapter 3: Three-Phase Systems & Symmetrical Components

3.1 Three-Phase Circuit Analysis (Wye and Delta Configurations & Transformations) 3.2 Balanced Three-Phase Power Calculations & Phasor Relationships 3.3 The Per-Unit (pu) System: Bases, Conversions & System Modeling 3.4 Symmetrical Components (Fortescue Transformation, Sequence Networks & Unbalance)

4 Chapter 4: Electric Power Transformers

4.1 Transformer Theory, Equivalent Circuits & Open/Short-Circuit Testing 4.2 Transformer Voltage Regulation, Efficiency & Loss Calculations 4.3 Three-Phase Transformer Connections, Phase Shifts & Paralleling 4.4 Autotransformers, Instrument Transformers (CTs & VTs) & Special Transformers

5 Chapter 5: Rotating Machines: Induction & Synchronous

5.1 Three-Phase Induction Motors: Principles, Equivalent Circuits & Slip-Torque Characteristics 5.2 Induction Motor Starting, Speed Control & Braking Methods 5.3 Synchronous Generators: Operation, Excitation, Power-Angle Equations & V-Curves 5.4 Synchronous Motors & Condensers for Power Factor Correction

6 Chapter 6: DC Machines & Power Devices

6.1 DC Generators & Motors: Types (Shunt, Series, Compound), Characteristics & Speed Control 6.2 Power Capacitors, Shunt Reactors & Harmonic Filter Design 6.3 Battery Energy Storage Systems (BESS) & Ultra-Capacitors 6.4 Renewable Generation Integration: Solar Photovoltaics (PV) & Wind Power Systems

7 Chapter 7: Power Electronics & Industrial Controls

7.1 Power Semiconductor Switching Devices (Diodes, Thyristors, MOSFETs, IGBTs) 7.2 AC-to-DC Converters (Uncontrolled & Controlled Rectifiers) 7.3 DC-to-DC Switch-Mode Converters (Buck, Boost, Buck-Boost) & DC-AC Inverters 7.4 Variable Frequency Drives (VFDs), Motor Starters & Ladder Logic / PLC Controls

8 Chapter 8: Transmission & Distribution Systems

8.1 Transmission Line Parameters (Resistance, Inductance, Capacitance & GMD/GMR) 8.2 Line Models (Short, Medium Nominal-π, Long Lines) & ABCD Two-Port Parameters 8.3 Surge Impedance, Surge Impedance Loading (SIL) & Voltage Regulation 8.4 Distribution System Architectures, Voltage Drops & Feeder Loading 8.5 Power Flow Studies: Bus Classification, Y-Bus & Newton-Raphson Solutions 8.6 Power System Stability: Swing Equation, Equal-Area Criterion & Critical Clearing Time

9 Chapter 9: Power System Fault Analysis

9.1 Fault Analysis Fundamentals & Subtransient/Transient Machine Reactances 9.2 Three-Phase Symmetrical Fault Calculations 9.3 Single Line-to-Ground (SLG) & Line-to-Line (LL) Fault Analysis 9.4 Double Line-to-Ground (DLG) Faults & Bus Impedance Matrix (Zbus) Methods

10 Chapter 10: Power System Protection & Coordination

10.1 Protective Relaying Principles, IEEE Device Designations & Instrument Transformers 10.2 Overcurrent Protection (50/51), Time-Current Curves (TCC) & Relay Coordination 10.3 Differential Protection (87) for Transformers, Busbars & Generators 10.4 Distance / Impedance Protection (21) for Transmission Lines & Directional Relays (67)

11 Chapter 11: National Electrical Code (NEC) & Installation Design

11.1 NEC Fundamentals, Branch Circuit & Feeder Conductor Sizing (Ampacity & Derating) 11.2 Overcurrent Protection Sizing, Raceway Fill & Box Fill Calculations 11.3 Motor Branch Circuits, Controllers & Feeder Protection (NEC Article 430) 11.4 Grounding and Bonding Systems per NEC Article 250

12 Chapter 12: Electrical Safety, Standards & Facility Applications

12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones, T-Codes & Sealing (NEC Articles 500-506) 12.2 Electrical Safety in the Workplace: NFPA 70E & Arc Flash Hazard Calculations 12.3 National Electrical Safety Code (NESC) Clearance & Utility Safety Requirements 12.4 Facility Applications: Illumination Design, Demand/Connected Loads & Lightning/Surge Protection 12.5 Special Occupancies & Systems: Health Care, Fire Pumps, Pools, Emergency & Standby (NEC Chapters 5-7)

9.4 Double Line-to-Ground (DLG) Faults & Bus Impedance Matrix (Zbus) Methods

Key Takeaways Explain This Topic AI

Double Line-to-Ground (DLG / 2LG) faults (~10% of all faults) involve two phase conductors shorted to each other and simultaneously connected to ground; boundary conditions on phases B and C (I_a = 0, V_b = 0, V_c = 0 for bolted fault) require all three sequence voltages to be equal: V_a0 = V_a1 = V_a2.

The sequence network interconnection for a DLG fault is a PARALLEL connection of all three sequence networks (positive, negative, and zero sequence networks connected in parallel at the fault point); the positive-sequence current is I_a1 = V_f / [Z_1 + (Z_2 || (Z_0 + 3*Z_f))].

The total ground return current during a DLG fault is I_ground = I_b + I_c = 3 * I_a0 = -3 * I_a1 * [Z_2 / (Z_2 + Z_0 + 3*Z_f)].

The Bus Impedance Matrix (Zbus = Ybus⁻¹) is the most powerful analytical tool for system-wide fault calculations; the diagonal element Z_kk represents the exact Thevenin driving-point impedance seen at Bus k, enabling instantaneous 3-phase fault calculation as I_f,k = V_f / Z_kk without performing network reduction.

Off-diagonal elements Z_ik represent transfer impedances between Bus i and Bus k; during a short circuit at Bus k, the post-fault bus voltages across the entire grid are computed directly via superposition as V_i^(f) = V_i^(0) - Z_ik * I_f,k, and line currents as I_ij^(f) = (V_i^(f) - V_j^(f)) / z_ij.

Last updated: August 2026

9.4 Double Line-to-Ground (DLG) Faults & Bus Impedance Matrix (Zbus) Methods

In complex, interconnected power systems containing dozens or hundreds of substations, manual network reduction (series-parallel and delta-wye transformations) is completely impractical. Modern power engineering and automated relay setting software rely on the Bus Impedance Matrix ( Z b u s Z_{bus} Z b u s ​ ) to perform rapid, exact short-circuit calculations across entire power grids.

On the NCEES PE Electrical and Computer: Power examination , fault analysis questions in this domain test your capability to analyze Double Line-to-Ground (DLG) sequence network interconnections, compute ground return fault currents, interpret diagonal ( Z k k Z_{kk} Z kk ​ ) and off-diagonal ( Z i k Z_{ik} Z ik ​ ) elements of Z b u s Z_{bus} Z b u s ​ , and calculate post-fault bus voltages and line currents without recalculating network equivalents.

1. Double Line-to-Ground (DLG / 2LG) Fault Analysis

A Double Line-to-Ground fault occurs when two phase conductors (conventionally Phase B and Phase C) short-circuit to each other and simultaneously contact earth ground through a fault impedance Z f Z_f Z f ​ and neutral/ground impedance Z g Z_g Z g ​ . DOUBLE LINE-TO-GROUND (DLG) FAULT TOPOLOGY

Phase A o----------------------------------o I_a = 0 (Open)

  • Phase B o----------------+-----------------o Fault Current: I_b
  • |
  • +---+
  • | | Z_f
  • +---+
  • |
  • Phase C o----------------+-----------------o Fault Current: I_c
  • |
  • +---+
  • | | Z_f
  • +---+
  • |
  • +---+
  • | | Z_g (Ground Return Path)
  • +---+
  • |
  • ===

Boundary Conditions (Bolted Fault on Phases B and C to Ground: Z f = 0 , Z g = 0 Z_f = 0, Z_g = 0 Z f ​ = 0 , Z g ​ = 0 )

  • I a = 0 I_a = 0 I a ​ = 0
  • V b = 0 V_b = 0 V b ​ = 0
  • V c = 0 V_c = 0 V c ​ = 0
  • Sequence Voltage and Current Relationships

Applying the inverse symmetrical component transformation to phase voltages ( V a ≠ 0 , V b = 0 , V c = 0 V_a \ne 0, V_b = 0, V_c = 0 V a ​  = 0 , V b ​ = 0 , V c ​ = 0 ): [ V a 0 V a 1 V a 2 ] = 1 3 [ 1 1 1 1 a a 2 1 a 2 a ] [ V a 0 0 ] = 1 3 [ V a V a V a ] \begin{bmatrix} V_{a0} \\ V_{a1} \\ V_{a2} \end{bmatrix} = \frac{1}{3} \begin{bmatrix} 1 & 1 & 1 \\ 1 & a & a^2 \\ 1 & a^2 & a \end{bmatrix} \begin{bmatrix} V_a \\ 0 \\ 0 \end{bmatrix} = \frac{1}{3} \begin{bmatrix} V_a \\ V_a \\ V_a \end{bmatrix} ​ V a 0 ​ V a 1 ​ V a 2 ​ ​ ​ = 3 1 ​ ​ 1 1 1 ​ 1 a a 2 ​ 1 a 2 a ​ ​ ​ V a ​ 0 0 ​ ​ = 3 1 ​ ​ V a ​ V a ​ V a ​ ​ ​ V a 0 = V a 1 = V a 2 = V a 3 V_{a0} = V_{a1} = V_{a2} = \frac{V_a}{3} V a 0 ​ = V a 1 ​ = V a 2 ​ = 3 V a ​ ​

From the current boundary condition I a = 0 I_a = 0 I a ​ = 0 : I a = I a 0 + I a 1 + I a 2 = 0 ⟹ I a 0 + I a 1 + I a 2 = 0 I_a = I_{a0} + I_{a1} + I_{a2} = 0 \implies I_{a0} + I_{a1} + I_{a2} = 0 I a ​ = I a 0 ​ + I a 1 ​ + I a 2 ​ = 0 ⟹ I a 0 ​ + I a 1 ​ + I a 2 ​ = 0

Sequence Network Interconnection: PARALLEL Connection of All Three Networks

Because the sequence voltages at the fault point are identical ( V a 0 = V a 1 = V a 2 V_{a0} = V_{a1} = V_{a2} V a 0 ​ = V a 1 ​ = V a 2 ​ ) and the three sequence currents sum to zero, all three sequence networks (Positive, Negative, and Zero) must be connected in PARALLEL at the fault point. DLG SEQUENCE NETWORK INTERCONNECTION (PARALLEL)

  • +---[ Z_1 ]---(~) V_f (Positive Sequence)
  • | |
  • +-----+---------------+-----+ I_a1 (Inflow)
  • | |
  • | +---[ Z_2 ]-----+ | I_a2 (Outflow)
  • | | (Negative Seq)| |
  • +-----+---------------+-----+
  • | |
  • | +---[ Z_0 + 3Z_g ]--+ | I_a0 (Outflow)
  • | | (Zero Sequence) | |
  • +-----+-------------------+-----+
  • | |
  • +-------------------------------+ Reference Bus
  • Master DLG Sequence Current Formulas

From the parallel combination of the negative and zero sequence branches: Z p a r a l l e l = Z 2 ∥ ( Z 0 + 3 Z f + 3 Z g ) = Z 2 ( Z 0 + 3 Z f + 3 Z g ) Z 2 + Z 0 + 3 Z f + 3 Z g Z_{parallel} = Z_2 \parallel (Z_0 + 3 Z_f + 3 Z_g) = \frac{Z_2 (Z_0 + 3 Z_f + 3 Z_g)}{Z_2 + Z_0 + 3 Z_f + 3 Z_g} Z p a r a ll e l ​ = Z 2 ​ ∥ ( Z 0 ​ + 3 Z f ​ + 3 Z g ​ ) = Z 2 ​ + Z 0 ​ + 3 Z f ​ + 3 Z g ​ Z 2 ​ ( Z 0 ​ + 3 Z f ​ + 3 Z g ​ ) ​ I a 1 = V f Z 1 + Z p a r a l l e l = V f Z 1 + Z 2 ( Z 0 + 3 Z f + 3 Z g ) Z 2 + Z 0 + 3 Z f + 3 Z g [ pu ] I_{a1} = \frac{V_f}{Z_1 + Z_{parallel}} = \frac{V_f}{Z_1 + \frac{Z_2 (Z_0 + 3 Z_f + 3 Z_g)}{Z_2 + Z_0 + 3 Z_f + 3 Z_g}} \quad [\text{pu}] I a 1 ​ = Z 1 ​ + Z p a r a ll e l ​ V f ​ ​ = Z 1 ​ + Z 2 ​ + Z 0 ​ + 3 Z f ​ + 3 Z g ​ Z 2 ​ ( Z 0 ​ + 3 Z f ​ + 3 Z g ​ ) ​ V f ​ ​ [ pu ]

Applying current division to find the negative and zero sequence currents: I a 2 = − I a 1 ( Z 0 + 3 Z f + 3 Z g Z 2 + Z 0 + 3 Z f + 3 Z g ) [ pu ] I_{a2} = -I_{a1} \left( \frac{Z_0 + 3 Z_f + 3 Z_g}{Z_2 + Z_0 + 3 Z_f + 3 Z_g} \right) \quad [\text{pu}] I a 2 ​ = − I a 1 ​ ( Z 2 ​ + Z 0 ​ + 3 Z f ​ + 3 Z g ​ Z 0 ​ + 3 Z f ​ + 3 Z g ​ ​ ) [ pu ] I a 0 = − I a 1 ( Z 2 Z 2 + Z 0 + 3 Z f + 3 Z g ) [ pu ] I_{a0} = -I_{a1} \left( \frac{Z_2}{Z_2 + Z_0 + 3 Z_f + 3 Z_g} \right) \quad [\text{pu}] I a 0 ​ = − I a 1 ​ ( Z 2 ​ + Z 0 ​ + 3 Z f ​ + 3 Z g ​ Z 2 ​ ​ ) [ pu ]

Total Ground Return Current ( I g r o u n d I_{ground} I g ro u n d ​ ) I g r o u n d = I b + I c = 3 I a 0 = − 3 I a 1 ( Z 2 Z 2 + Z 0 + 3 Z f + 3 Z g ) [ pu ] I_{ground} = I_b + I_c = 3 I_{a0} = -3 I_{a1} \left( \frac{Z_2}{Z_2 + Z_0 + 3 Z_f + 3 Z_g} \right) \quad [\text{pu}] I g ro u n d ​ = I b ​ + I c ​ = 3 I a 0 ​ = − 3 I a 1 ​ ( Z 2 ​ + Z 0 ​ + 3 Z f ​ + 3 Z g ​ Z 2 ​ ​ ) [ pu ]

2. Master Comparative Summary of All Four Fault Types +---------------------------------------------------------------------------------------------------+

  • | POWER SYSTEM FAULT COMPARISON MASTER TABLE |
  • +---------------------------------------------------------------------------------------------------+
  • | Feature | 3-Phase (3Φ) | Single Line-Ground (SLG)| Line-to-Line (L-L) | Double Line-Ground (DLG)|
  • | :--- | :--- | :--- | :--- | :--- |
  • | **Symbolic Code** | $3\text{P} / 3\text{LG}$ | $1\text{LG}$ | $2\text{L}$ | $2\text{LG}$ |
  • | **Statistical %** | $\sim 5\%$ | $\sim 70\%$ | $\sim 15\%$ | $\sim 10\%$ |
  • | **Boundary** | $V_a = V_b = V_c$ | $I_b = 0, I_c = 0$ | $I_a = 0, I_b=-I_c$| $I_a = 0$ |
  • | **Conditions** | $I_a+I_b+I_c=0$ | $V_a = 0$ | $V_b = V_c$ | $V_b = 0, V_c = 0$ |
  • | **Sequence** | $I_{a2} = 0$ | $I_{a0}=I_{a1}=I_{a2}$ | $I_{a0} = 0$ | $V_{a0}=V_{a1}=V_{a2}$ |
  • | **Relationships** | $I_{a0} = 0$ | $= I_a / 3$ | $I_{a1} = -I_{a2}$ | $I_{a0}+I_{a1}+I_{a2}=0$|
  • | **Network** | Positive Sequence | **SERIES** of Pos, | **PARALLEL** of | **PARALLEL** of Pos, |
  • | **Topology** | Only | Neg, and Zero Networks | Pos & Neg (Zero Open)| Neg, and Zero Networks|

| **Positive Seq.** | $I_{a1} = \frac{V_f}{Z_1}$| $I_{a1} = \frac{V_f}{Z_1+Z_2+Z_0}$| $I_{a1} = \frac{V_f}{Z_1+Z_2}$| $I_{a1} = \frac{V_f}{Z_1 + (Z_2 \parallel Z_0)}$ |

| **Current (I_a1)**| | | | |

| **Phase Fault** | $I_{f} = \frac{V_f}{Z_1}$ | $I_a = 3 I_{a0}$ | $|I_b| = \sqrt{3} |I_{a1}|$ | $|I_b|, |I_c|$ from |

  • | **Current** | | $= \frac{3V_f}{Z_1+Z_2+Z_0}$ | $= \frac{\sqrt{3}V_f}{Z_1+Z_2}$ | transformation matrix |
  • | **Ground Current**| $0$ | $I_{ground} = I_a$ | $0$ | $I_{ground} = 3 I_{a0}$ |
  • | **(I_ground)** | | $= 3 I_{a0}$ | | |
  • +---------------------------------------------------------------------------------------------------+
  • 3. The Bus Impedance Matrix ( Z b u s Z_{bus} Z b u s ​ ) Method

In nodal network analysis, the power system is represented by the Bus Admittance Matrix ( Y b u s Y_{bus} Y b u s ​ ) , which is sparse and computationally efficient for load flow studies. However, for short-circuit calculations, the Bus Impedance Matrix ( Z b u s Z_{bus} Z b u s ​ ) is the primary analytical tool because it directly contains all system Thevenin and transfer impedances. Z b u s = Y b u s − 1 Z_{bus} = Y_{bus}^{-1} Z b u s ​ = Y b u s − 1 ​ V b u s = Z b u s I b u s \mathbf{V}_{bus} = Z_{bus} \mathbf{I}_{bus} V b u s ​ = Z b u s ​ I b u s ​ STRUCTURE OF THE BUS IMPEDANCE MATRIX (Z_bus)

  • Bus 1 Bus 2 ... Bus k ... Bus N
  • Bus 1 [ Z_11 Z_12 ... Z_1k ... Z_1N ]
  • Bus 2 [ Z_21 Z_22 ... Z_2k ... Z_2N ]
  • : [ : : ... : ... : ]
  • Z_bus = Bus k [ Z_k1 Z_k2 ... Z_kk ... Z_kN ]
  • : [ : : ... : ... : ]
  • Bus N [ Z_N1 Z_N2 ... Z_Nk ... Z_NN ]
  • Physical Significance of Matrix Elements

Diagonal Elements ( Z k k Z_{kk} Z kk ​ - Driving-Point Impedance): Z k k Z_{kk} Z kk ​ is the exact Thevenin equivalent impedance seen looking into Bus k k k with all system voltage sources shorted to ground ( Z t h , k = Z k k Z_{th,k} = Z_{kk} Z t h , k ​ = Z kk ​ ).

Off-Diagonal Elements ( Z i k Z_{ik} Z ik ​ - Transfer Impedance): Z i k Z_{ik} Z ik ​ represents the open-circuit voltage response produced at Bus i i i due to a unit current injected at Bus k k k ( Z i k = V i I k ∣ I m = 0 , m ≠ k Z_{ik} = \frac{V_i}{I_k}\Big|_{I_m = 0, m \ne k} Z ik ​ = I k ​ V i ​ ​ ​ I m ​ = 0 , m  = k ​ ). By reciprocity in bilateral networks, Z i k = Z k i Z_{ik} = Z_{ki} Z ik ​ = Z ki ​ .

4. Calculating Fault Currents, Bus Voltages, and Line Flows Using Z b u s Z_{bus} Z b u s ​

Consider an N N N -bus power system operating at prefault bus voltages V ( 0 ) = [ V 1 ( 0 ) V 2 ( 0 ) … V N ( 0 ) ] T \mathbf{V}^{(0)} = \begin{bmatrix} V_1^{(0)} & V_2^{(0)} & \dots & V_N^{(0)} \end{bmatrix}^T V ( 0 ) = [ V 1 ( 0 ) ​ ​ V 2 ( 0 ) ​ ​ … ​ V N ( 0 ) ​ ​ ] T (typically 1.0 ∠ 0 ∘ pu 1.0\angle 0^\circ\text{ pu} 1.0∠ 0 ∘ pu ). +---------------------------------------------------------------------------------------------------+

  • | Z_bus FAULT CALCULATION ALGORITHM (BUS k FAULT) |
  • +---------------------------------------------------------------------------------------------------+
  • | Step 1: Three-Phase Symmetrical Fault Current at Bus k: |
  • | |
  • | I_f,k = V_k^(0) / (Z_kk + Z_f) |
  • | |
  • | Step 2: Post-Fault Voltages at EVERY Bus i (i = 1, 2, ..., N): |
  • | Applying superposition with fault current injection (-I_f,k) at Bus k: |
  • | |
  • | V_i^(f) = V_i^(0) - Z_ik * I_f,k = V_i^(0) - (Z_ik / (Z_kk + Z_f)) * V_k^(0) |
  • | |
  • | * Note: At the faulted bus itself (i = k) for a bolted fault (Z_f = 0): |
  • | V_k^(f) = V_k^(0) - Z_kk * (V_k^(0) / Z_kk) = 0.0 pu |
  • | |
  • | Step 3: Post-Fault Branch Currents in Line connecting Bus i to Bus j: |
  • | |
  • | I_ij^(f) = (V_i^(f) - V_j^(f)) / z_ij,line |
  • | where z_ij,line is the actual series branch impedance of line i-j. |
  • +---------------------------------------------------------------------------------------------------+
  • Sequence Z b u s Z_{bus} Z b u s ​ Matrices for Unsymmetrical Faults

To perform unsymmetrical fault calculations at Bus k k k , we construct the three sequence bus impedance matrices:

Positive-Sequence Matrix: Z b u s ( 1 ) = [ Y b u s ( 1 ) ] − 1 Z_{bus}^{(1)} = [Y_{bus}^{(1)}]^{-1} Z b u s ( 1 ) ​ = [ Y b u s ( 1 ) ​ ] − 1

Negative-Sequence Matrix: Z b u s ( 2 ) = [ Y b u s ( 2 ) ] − 1 Z_{bus}^{(2)} = [Y_{bus}^{(2)}]^{-1} Z b u s ( 2 ) ​ = [ Y b u s ( 2 ) ​ ] − 1

Zero-Sequence Matrix: Z b u s ( 0 ) = [ Y b u s ( 0 ) ] − 1 Z_{bus}^{(0)} = [Y_{bus}^{(0)}]^{-1} Z b u s ( 0 ) ​ = [ Y b u s ( 0 ) ​ ] − 1 Single Line-to-Ground (SLG) Fault at Bus k : I f , k , S L G = 3 V k ( 0 ) Z k k ( 1 ) + Z k k ( 2 ) + Z k k ( 0 ) + 3 Z f \text{Single Line-to-Ground (SLG) Fault at Bus } k: \quad I_{f,k,SLG} = \frac{3 V_k^{(0)}}{Z_{kk}^{(1)} + Z_{kk}^{(2)} + Z_{kk}^{(0)} + 3 Z_f} Single Line-to-Ground (SLG) Fault at Bus k : I f , k , S L G ​ = Z kk ( 1 ) ​ + Z kk ( 2 ) ​ + Z kk ( 0 ) ​ + 3 Z f ​ 3 V k ( 0 ) ​ ​ Line-to-Line (L-L) Fault at Bus k : ∣ I f , k , L L ∣ = 3 ∣ V k ( 0 ) ∣ ∣ Z k k ( 1 ) + Z k k ( 2 ) + Z f ∣ \text{Line-to-Line (L-L) Fault at Bus } k: \quad |I_{f,k,LL}| = \frac{\sqrt{3} |V_k^{(0)}|}{|Z_{kk}^{(1)} + Z_{kk}^{(2)} + Z_f|} Line-to-Line (L-L) Fault at Bus k : ∣ I f , k , LL ​ ∣ = ∣ Z kk ( 1 ) ​ + Z kk ( 2 ) ​ + Z f ​ ∣ 3 ​ ∣ V k ( 0 ) ​ ∣ ​ Double Line-to-Ground (DLG) Fault at Bus k : I a 1 , k = V k ( 0 ) Z k k ( 1 ) + Z k k ( 2 ) ( Z k k ( 0 ) + 3 Z f ) Z k k ( 2 ) + Z k k ( 0 ) + 3 Z f \text{Double Line-to-Ground (DLG) Fault at Bus } k: \quad I_{a1,k} = \frac{V_k^{(0)}}{Z_{kk}^{(1)} + \frac{Z_{kk}^{(2)} (Z_{kk}^{(0)} + 3 Z_f)}{Z_{kk}^{(2)} + Z_{kk}^{(0)} + 3 Z_f}} Double Line-to-Ground (DLG) Fault at Bus k : I a 1 , k ​ = Z kk ( 1 ) ​ + Z kk ( 2 ) ​ + Z kk ( 0 ) ​ + 3 Z f ​ Z kk ( 2 ) ​ ( Z kk ( 0 ) ​ + 3 Z f ​ ) ​ V k ( 0 ) ​ ​

  • 5. Step-by-Step Worked Mathematical Example
  • Problem Statement

A 3-bus, 60 Hz 60\text{ Hz} 60 Hz power transmission system has a base of 100 MVA 100\text{ MVA} 100 MVA and nominal line-to-line voltage of 138 kV 138\text{ kV} 138 kV ( I b a s e = 418.37 A I_{base} = 418.37\text{ A} I ba se ​ = 418.37 A ). The positive-sequence and zero-sequence bus impedance matrices ( Z b u s ( 1 ) Z_{bus}^{(1)} Z b u s ( 1 ) ​ and Z b u s ( 0 ) Z_{bus}^{(0)} Z b u s ( 0 ) ​ ) in per-unit are: Z b u s ( 1 ) = Z b u s ( 2 ) = [ j 0.12 j 0.08 j 0.04 j 0.08 j 0.20 j 0.10 j 0.04 j 0.10 j 0.16 ] [ pu ] , Z b u s ( 0 ) = [ j 0.24 j 0.10 j 0.05 j 0.10 j 0.30 j 0.12 j 0.05 j 0.12 j 0.25 ] [ pu ] Z_{bus}^{(1)} = Z_{bus}^{(2)} = \begin{bmatrix} j0.12 & j0.08 & j0.04 \\ j0.08 & j0.20 & j0.10 \\ j0.04 & j0.10 & j0.16 \end{bmatrix} \quad [\text{pu}], \qquad Z_{bus}^{(0)} = \begin{bmatrix} j0.24 & j0.10 & j0.05 \\ j0.10 & j0.30 & j0.12 \\ j0.05 & j0.12 & j0.25 \end{bmatrix} \quad [\text{pu}] Z b u s ( 1 ) ​ = Z b u s ( 2 ) ​ = ​ j 0.12 j 0.08 j 0.04 ​ j 0.08 j 0.20 j 0.10 ​ j 0.04 j 0.10 j 0.16 ​ ​ [ pu ] , Z b u s ( 0 ) ​ = ​ j 0.24 j 0.10 j 0.05 ​ j 0.10 j 0.30 j 0.12 ​ j 0.05 j 0.12 j 0.25 ​ ​ [ pu ]

Assume prefault voltages at all buses are V 1 ( 0 ) = V 2 ( 0 ) = V 3 ( 0 ) = 1.0 ∠ 0 ∘ pu V_1^{(0)} = V_2^{(0)} = V_3^{(0)} = 1.0\angle 0^\circ\text{ pu} V 1 ( 0 ) ​ = V 2 ( 0 ) ​ = V 3 ( 0 ) ​ = 1.0∠ 0 ∘ pu .

A bolted short circuit occurs on Bus 2 ( Z f = 0 Z_f = 0 Z f ​ = 0 ).

Calculate:

The bolted Three-Phase fault current ( I f , 2 , 3 ϕ I_{f,2,3\phi} I f , 2 , 3 ϕ ​ ) at Bus 2 in per-unit and physical Amperes.

The post-fault bus voltages ( V 1 ( f ) , V 2 ( f ) , V 3 ( f ) V_1^{(f)}, V_2^{(f)}, V_3^{(f)} V 1 ( f ) ​ , V 2 ( f ) ​ , V 3 ( f ) ​ ) at all three buses during the 3-phase fault at Bus 2.

The fault current flowing in Transmission Line 1-2 during the Bus 2 fault, given the actual series branch line impedance is z 12 , l i n e = j 0.125 pu z_{12,line} = j0.125\text{ pu} z 12 , l in e ​ = j 0.125 pu .

The sequence currents ( I a 1 , I a 2 , I a 0 I_{a1}, I_{a2}, I_{a0} I a 1 ​ , I a 2 ​ , I a 0 ​ ), total ground return current ( I g r o u n d I_{ground} I g ro u n d ​ ), and phase currents ( I b , I c I_b, I_c I b ​ , I c ​ ) if the fault at Bus 2 is a bolted Double Line-to-Ground (DLG) fault. =========================================================================================

CALCULATION WORKFLOW & DETAILED STEP-BY-STEP SOLUTION:

=========================================================================================

Step 1: Three-Phase Symmetrical Fault Current at Bus 2

The Thevenin driving-point impedance at Bus 2 is the diagonal element Z_22^(1):

Z_th,2 = Z_22^(1) = j0.20 pu

Fault Current:

I_f,2 = V_2^(0) / Z_22^(1) = (1.0 /_ 0°) / (j0.20) = -j5.0000 pu = 5.0000 /_ -90° pu

Actual Physical Current:

  • I_base = (100 * 10^6 VA) / (sqrt(3) * 138,000 V) = 418.37 A
  • I_f,2,actual = 5.0000 * 418.37 A = 2,091.85 A ≈ 2.09 kA rms

Step 2: Post-Fault Bus Voltages During Bus 2 Three-Phase Fault

Using transfer impedances from column 2 of Z_bus^(1) (Z_12 = j0.08, Z_22 = j0.20, Z_32 = j0.10):

Bus 1 Post-Fault Voltage:

  • V_1^(f) = V_1^(0) - Z_12^(1) * I_f,2
  • = 1.0 - (j0.08) * (-j5.0000)
  • = 1.0 - (0.4000) = 0.6000 /_ 0° pu

Bus 2 Post-Fault Voltage (Faulted Bus):

  • V_2^(f) = V_2^(0) - Z_22^(1) * I_f,2
  • = 1.0 - (j0.20) * (-j5.0000)
  • = 1.0 - (1.0000) = 0.0000 pu (Zero voltage at bolted fault)

Bus 3 Post-Fault Voltage:

  • V_3^(f) = V_3^(0) - Z_32^(1) * I_f,2
  • = 1.0 - (j0.10) * (-j5.0000)
  • = 1.0 - (0.5000) = 0.5000 /_ 0° pu
  • Step 3: Line 1-2 Current Flow During Fault at Bus 2
  • I_12^(f) = (V_1^(f) - V_2^(f)) / z_12,line
  • = (0.6000 - 0.0000) / (j0.125)
  • = 0.6000 / (j0.125) = -j4.8000 pu = 4.8000 /_ -90° pu

Actual Current in Line 1-2:

I_12,actual = 4.8000 * 418.37 A = 2,008.18 A ≈ 2.01 kA rms

Step 4: Double Line-to-Ground (DLG) Bolted Fault at Bus 2

Driving point impedances at Bus 2:

  • Z_22^(1) = j0.20 pu
  • Z_22^(2) = j0.20 pu
  • Z_22^(0) = j0.30 pu

Parallel combination of Negative and Zero sequence branches:

  • Z_parallel = (Z_22^(2) * Z_22^(0)) / (Z_22^(2) + Z_22^(0))
  • = (j0.20 * j0.30) / (j0.20 + j0.30)
  • = (-0.0600) / (j0.5000) = j0.1200 pu

Positive-Sequence Current:

  • I_a1 = V_2^(0) / (Z_22^(1) + Z_parallel)
  • = (1.0 /_ 0°) / (j0.20 + j0.120)
  • = 1.0 / (j0.3200) = -j3.1250 pu = 3.1250 /_ -90° pu

Negative-Sequence Current (Current Division):

  • I_a2 = -I_a1 * [ Z_22^(0) / (Z_22^(2) + Z_22^(0)) ]
  • = -(-j3.1250) * [ j0.30 / j0.50 ]
  • = +j3.1250 * 0.6000 = +j1.8750 pu = 1.8750 /_ 90° pu

Zero-Sequence Current (Current Division):

  • I_a0 = -I_a1 * [ Z_22^(2) / (Z_22^(2) + Z_22^(0)) ]
  • = -(-j3.1250) * [ j0.20 / j0.50 ]
  • = +j3.1250 * 0.4000 = +j1.2500 pu = 1.2500 /_ 90° pu

Check Sum of Sequence Currents: I_a = I_a0 + I_a1 + I_a2 = j1.250 - j3.125 + j1.875 = 0.00 pu (CONFIRMED)

Total Ground Return Current:

  • I_ground = 3 * I_a0 = 3 * (+j1.2500 pu) = +j3.7500 pu = 3.7500 /_ 90° pu
  • I_ground,actual = 3.7500 * 418.37 A = 1,568.89 A ≈ 1.57 kA rms

Phase Fault Currents (I_b, I_c):

  • I_b = I_a0 + a^2 * I_a1 + a * I_a2
  • = j1.2500 + (-j3.1250 /_ 240°) + (j1.8750 /_ 120°)
  • = j1.2500 + (3.1250 /_ 150°) + (1.8750 /_ 210°)
  • = j1.2500 + (-2.70633 + j1.56250) + (-1.62380 - j0.93750)
  • = -4.33013 + j1.87500 pu
  • |I_b| = sqrt( (-4.33013)^2 + (1.87500)^2 ) = sqrt( 18.7500 + 3.5156 ) = 4.7186 pu
  • I_b,actual = 4.7186 * 418.37 A = 1,974.13 A ≈ 1.97 kA rms
  • I_c = I_a0 + a * I_a1 + a^2 * I_a2 = +4.33013 + j1.87500 pu
  • |I_c| = 4.7186 pu (1,974.13 A ≈ 1.97 kA rms)

Check Ground Current: I_b + I_c = (-4.33013 + j1.87500) + (4.33013 + j1.87500) = +j3.7500 pu = I_ground (CONFIRMED)

  • =========================================================================================
  • 6. Common PE Exam Traps & Tactical Pitfalls

Confusing Diagonal ( Z k k Z_{kk} Z kk ​ ) and Off-Diagonal ( Z i k Z_{ik} Z ik ​ ) Roles: Using Z i k Z_{ik} Z ik ​ to compute the fault current at Bus k k k . The fault current at Bus k k k depends strictly on the driving-point impedance Z k k Z_{kk} Z kk ​ . The off-diagonal element Z i k Z_{ik} Z ik ​ is used exclusively to compute the voltage dip at remote Bus i i i caused by the fault at Bus k k k .

Using Line Impedance Instead of Z k k Z_{kk} Z kk ​ for Bus Faults: Calculating fault current at a bus using the series impedance of the transmission line connected to it. The bus fault current is governed by the entire system Thevenin equivalent Z k k Z_{kk} Z kk ​ , which accounts for all parallel paths and generation sources across the entire network.

Sign Error in Post-Fault Bus Voltage Calculation: Writing V i ( f ) = V i ( 0 ) + Z i k I f , k V_i^{(f)} = V_i^{(0)} + Z_{ik} I_{f,k} V i ( f ) ​ = V i ( 0 ) ​ + Z ik ​ I f , k ​ . Because fault current flows out of the system into the short circuit, the voltage response is a subtraction: V i ( f ) = V i ( 0 ) − Z i k I f , k V_i^{(f)} = V_i^{(0)} - Z_{ik} I_{f,k} V i ( f ) ​ = V i ( 0 ) ​ − Z ik ​ I f , k ​ .

DLG Sequence Current Inversion: Forgetting the negative sign in the current division formulas for negative and zero sequence currents ( I a 2 = − I a 1 Z 0 Z 2 + Z 0 I_{a2} = -I_{a1} \frac{Z_0}{Z_2 + Z_0} I a 2 ​ = − I a 1 ​ Z 2 ​ + Z 0 ​ Z 0 ​ ​ ). Because I a 1 I_{a1} I a 1 ​ flows into the parallel network, I a 2 I_{a2} I a 2 ​ and I a 0 I_{a0} I a 0 ​ flow out, requiring an explicit negative sign to satisfy I a 0 + I a 1 + I a 2 = 0 I_{a0} + I_{a1} + I_{a2} = 0 I a 0 ​ + I a 1 ​ + I a 2 ​ = 0 .

Loading diagram... Zbus Fault Current Injection and System-Wide Voltage Profile Determination