Study guide

7.3 DC-to-DC Switch-Mode Converters (Buck, Boost, Buck-Boost) & DC-AC Inverters

PE Electrical and Computer Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview & Power Engineering Fundamentals

1.1 PE Power Exam Structure, Official Specification & NCEES Reference Strategy 1.2 Units, Conversions, Engineering Constants & Fundamental Power Equations 1.3 Measurement & Metering Principles (Power, Energy, Power Factor) 1.4 Instrument Testing & Diagnostics (Insulation Megger & Ground Resistance)

2 Chapter 2: Circuit Analysis Fundamentals

2.1 DC Circuit Laws, Network Theorems (Thevenin, Norton, Superposition) & Transients 2.2 Single-Phase AC Steady-State Analysis, Phasors & Impedance 2.3 AC Power Relationships (Real, Reactive, Apparent Power & Power Factor Correction) 2.4 Resonance, Frequency Response & Harmonic Distortion

3 Chapter 3: Three-Phase Systems & Symmetrical Components

3.1 Three-Phase Circuit Analysis (Wye and Delta Configurations & Transformations) 3.2 Balanced Three-Phase Power Calculations & Phasor Relationships 3.3 The Per-Unit (pu) System: Bases, Conversions & System Modeling 3.4 Symmetrical Components (Fortescue Transformation, Sequence Networks & Unbalance)

4 Chapter 4: Electric Power Transformers

4.1 Transformer Theory, Equivalent Circuits & Open/Short-Circuit Testing 4.2 Transformer Voltage Regulation, Efficiency & Loss Calculations 4.3 Three-Phase Transformer Connections, Phase Shifts & Paralleling 4.4 Autotransformers, Instrument Transformers (CTs & VTs) & Special Transformers

5 Chapter 5: Rotating Machines: Induction & Synchronous

5.1 Three-Phase Induction Motors: Principles, Equivalent Circuits & Slip-Torque Characteristics 5.2 Induction Motor Starting, Speed Control & Braking Methods 5.3 Synchronous Generators: Operation, Excitation, Power-Angle Equations & V-Curves 5.4 Synchronous Motors & Condensers for Power Factor Correction

6 Chapter 6: DC Machines & Power Devices

6.1 DC Generators & Motors: Types (Shunt, Series, Compound), Characteristics & Speed Control 6.2 Power Capacitors, Shunt Reactors & Harmonic Filter Design 6.3 Battery Energy Storage Systems (BESS) & Ultra-Capacitors 6.4 Renewable Generation Integration: Solar Photovoltaics (PV) & Wind Power Systems

7 Chapter 7: Power Electronics & Industrial Controls

7.1 Power Semiconductor Switching Devices (Diodes, Thyristors, MOSFETs, IGBTs) 7.2 AC-to-DC Converters (Uncontrolled & Controlled Rectifiers) 7.3 DC-to-DC Switch-Mode Converters (Buck, Boost, Buck-Boost) & DC-AC Inverters 7.4 Variable Frequency Drives (VFDs), Motor Starters & Ladder Logic / PLC Controls

8 Chapter 8: Transmission & Distribution Systems

8.1 Transmission Line Parameters (Resistance, Inductance, Capacitance & GMD/GMR) 8.2 Line Models (Short, Medium Nominal-π, Long Lines) & ABCD Two-Port Parameters 8.3 Surge Impedance, Surge Impedance Loading (SIL) & Voltage Regulation 8.4 Distribution System Architectures, Voltage Drops & Feeder Loading 8.5 Power Flow Studies: Bus Classification, Y-Bus & Newton-Raphson Solutions 8.6 Power System Stability: Swing Equation, Equal-Area Criterion & Critical Clearing Time

9 Chapter 9: Power System Fault Analysis

9.1 Fault Analysis Fundamentals & Subtransient/Transient Machine Reactances 9.2 Three-Phase Symmetrical Fault Calculations 9.3 Single Line-to-Ground (SLG) & Line-to-Line (LL) Fault Analysis 9.4 Double Line-to-Ground (DLG) Faults & Bus Impedance Matrix (Zbus) Methods

10 Chapter 10: Power System Protection & Coordination

10.1 Protective Relaying Principles, IEEE Device Designations & Instrument Transformers 10.2 Overcurrent Protection (50/51), Time-Current Curves (TCC) & Relay Coordination 10.3 Differential Protection (87) for Transformers, Busbars & Generators 10.4 Distance / Impedance Protection (21) for Transmission Lines & Directional Relays (67)

11 Chapter 11: National Electrical Code (NEC) & Installation Design

11.1 NEC Fundamentals, Branch Circuit & Feeder Conductor Sizing (Ampacity & Derating) 11.2 Overcurrent Protection Sizing, Raceway Fill & Box Fill Calculations 11.3 Motor Branch Circuits, Controllers & Feeder Protection (NEC Article 430) 11.4 Grounding and Bonding Systems per NEC Article 250

12 Chapter 12: Electrical Safety, Standards & Facility Applications

12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones, T-Codes & Sealing (NEC Articles 500-506) 12.2 Electrical Safety in the Workplace: NFPA 70E & Arc Flash Hazard Calculations 12.3 National Electrical Safety Code (NESC) Clearance & Utility Safety Requirements 12.4 Facility Applications: Illumination Design, Demand/Connected Loads & Lightning/Surge Protection 12.5 Special Occupancies & Systems: Health Care, Fire Pumps, Pools, Emergency & Standby (NEC Chapters 5-7)

7.3 DC-to-DC Switch-Mode Converters (Buck, Boost, Buck-Boost) & DC-AC Inverters

Key Takeaways Explain This Topic AI

Switch-mode DC-DC converters regulate DC voltage with high efficiency (>90-95%) using inductive energy storage governed by two fundamental steady-state laws: Inductor Volt-Second Balance (net inductor voltage over a switching period is zero: ∫ v_L dt = 0) and Capacitor Charge/Ampere-Second Balance (net capacitor current over a switching period is zero: ∫ i_C dt = 0).

The three primary non-isolated DC-DC topologies in Continuous Conduction Mode (CCM) exhibit distinct voltage conversion ratios: Buck (step-down: Vout = D * Vin), Boost (step-up: Vout = Vin / (1 - D)), and Buck-Boost (inverting step-up/down: Vout = -Vin * D / (1 - D)), where duty cycle D = t_on / T_s.

Maintaining Continuous Conduction Mode (CCM) requires inductor sizing above the critical inductance threshold: Lmin = (1 - D) * R / (2 * f_sw) for Buck converters, and Lmin = D * (1 - D)² * R / (2 * f_sw) for Boost converters; operating below Lmin enters Discontinuous Conduction Mode (DCM), making Vout load-dependent.

Three-phase Voltage Source Inverters (VSI) in standard Sinusoidal Pulse-Width Modulation (SPWM) produce a fundamental line-to-line RMS output voltage of V_LL1,rms = (√3 / 2√2) * ma * Vdc ≈ 0.6124 * ma * Vdc in the linear modulation range (ma ≤ 1.0), where ma is the amplitude modulation index.

Space Vector PWM (SVPWM) maps the 8 inverter switching states into a rotating hexagon reference vector, yielding a 15.47% increase in DC bus voltage utilization compared to sinusoidal SPWM (V_LL1,rms,max = Vdc / √2 ≈ 0.7071 * Vdc for ma = 1.0) while reducing current harmonic distortion and switching transitions.

Last updated: August 2026

7.3 DC-to-DC Switch-Mode Converters (Buck, Boost, Buck-Boost) & DC-AC Inverters

Executive Overview: DC-DC switch-mode converters and DC-AC inverters constitute the power conversion core for solar photovoltaic (PV) string/central inverters, Battery Energy Storage Systems (BESS), electric vehicle (EV) powertrains, and industrial Variable Frequency Drives (VFDs). On the NCEES PE Electrical: Power exam, questions focus on steady-state volt-second balance derivations, duty cycle ( D D D ) relationships, inductor ripple current ( Δ I L \Delta I_L Δ I L ​ ), critical boundary inductance ( L m i n L_{min} L min ​ ) for Continuous Conduction Mode (CCM), output voltage ripple ( Δ V o u t \Delta V_{out} Δ V o u t ​ ), and inverter Sinusoidal PWM (SPWM) vs. Space Vector PWM (SVPWM) modulation index voltage scaling.

1. Governing Principles of Switch-Mode Power Conversion

High-efficiency DC-DC conversion relies on solid-state switches (MOSFETs or IGBTs) pulsing at switching frequencies ( f s w = 1 / T s f_{sw} = 1/T_s f s w ​ = 1/ T s ​ , typically 20 kHz − 500 kHz 20\text{ kHz} - 500\text{ kHz} 20 kHz − 500 kHz ) with duty ratio D = t o n T s D = \frac{t_{on}}{T_s} D = T s ​ t o n ​ ​ . In steady-state periodic operation, energy balance is enforced by two fundamental conservation laws: +---------------------------------------------------------------------------------------------------+

  • | STEADY-STATE ENERGY CONSERVATION LAWS |
  • +---------------------------------------------------------------------------------------------------+
  • | 1. Inductor Volt-Second Balance: |

| $$\int_0^{T_s} v_L(t) dt = 0 \implies \langle v_L \rangle = V_{L,on} \cdot D + V_{L,off} \cdot (1 - D) = 0$$ |

  • | (The average voltage across an ideal inductor over any complete switching cycle is zero). |
  • | |
  • | 2. Capacitor Charge (Ampere-Second) Balance: |

| $$\int_0^{T_s} i_C(t) dt = 0 \implies \langle i_C \rangle = I_{C,on} \cdot D + I_{C,off} \cdot (1 - D) = 0$$ |

  • | (The average current through an ideal capacitor over any complete switching cycle is zero). |
  • +---------------------------------------------------------------------------------------------------+

2. Continuous Conduction Mode (CCM) DC-DC Topologies +---------------------------------------------------------------------------------------------------+

  • | DC-DC CONVERTER TOPOLOGY & DESIGN MATRIX (CCM) |
  • +---------------------------------------------------------------------------------------------------+

| Topology | Voltage Conversion ($V_{out}$) | Inductor Ripple Current ($\Delta I_L$) | Critical Inductance ($L_{min}$) | Voltage Ripple Ratio ($\frac{\Delta V_{out}}{V_{out}}$) |

| :--- | :--- | :--- | :--- | :--- |

| **Buck** (Step-Down) | $V_{out} = D \cdot V_{in}$ | $\Delta I_L = \frac{V_{in} D (1 - D)}{f_{sw} L}$ | $L_{min} = \frac{(1 - D) R}{2 f_{sw}}$ | $\frac{\Delta V_{out}}{V_{out}} = \frac{1 - D}{8 L C f_{sw}^2}$ |

| **Boost** (Step-Up) | $V_{out} = \frac{V_{in}}{1 - D}$ | $\Delta I_L = \frac{V_{in} D}{f_{sw} L}$ | $L_{min} = \frac{D (1 - D)^2 R}{2 f_{sw}}$ | $\frac{\Delta V_{out}}{V_{out}} = \frac{D}{R C f_{sw}}$ |

| **Buck-Boost** (Inverting) | $V_{out} = -V_{in} \frac{D}{1 - D}$ | $\Delta I_L = \frac{V_{in} D}{f_{sw} L}$ | $L_{min} = \frac{(1 - D)^2 R}{2 f_{sw}}$ | $\frac{\Delta V_{out}}{V_{out}} = \frac{D}{R C f_{sw}}$ |

  • +---------------------------------------------------------------------------------------------------+
  • 1. Buck Converter (Step-Down) BUCK CONVERTER CIRCUIT TOPOLOGY
  • Switch (Q1) Inductor (L)
  • +---------[ / ]--------+--------[ZZZZ]--------+--------+ (+) V_out
  • | | | |
  • + | | | |
  • (~) V_in +--+--+ +---+ +---+
  • | (D1) /\ Freewheeling | | C | | R_load
  • | /--\ Diode +---+ +---+
  • | | | |
  • +----------------------+----------------------+--------+ (-) Common

Switch ON Interval ( 0 ≤ t ≤ D T s 0 \le t \le D T_s 0 ≤ t ≤ D T s ​ ): Q 1 Q_1 Q 1 ​ closed, D 1 D_1 D 1 ​ reverse-biased. Voltage across inductor is v L = V i n − V o u t v_L = V_{in} - V_{out} v L ​ = V in ​ − V o u t ​ . Current ramps up linearly: d i L d t = V i n − V o u t L \frac{di_L}{dt} = \frac{V_{in} - V_{out}}{L} d t d i L ​ ​ = L V in ​ − V o u t ​ ​

Switch OFF Interval ( D T s < t ≤ T s D T_s < t \le T_s D T s ​ < t ≤ T s ​ ): Q 1 Q_1 Q 1 ​ open, D 1 D_1 D 1 ​ forward-biased by inductor inductive kick. Voltage across inductor is v L = − V o u t v_L = -V_{out} v L ​ = − V o u t ​ . Current ramps down: d i L d t = − V o u t L \frac{di_L}{dt} = -\frac{V_{out}}{L} d t d i L ​ ​ = − L V o u t ​ ​

Volt-Second Balance Derivation: ( V i n − V o u t ) D T s + ( − V o u t ) ( 1 − D ) T s = 0 ⟹ V i n D − V o u t D − V o u t + V o u t D = 0 ⟹ V o u t = D ⋅ V i n (V_{in} - V_{out}) D T_s + (-V_{out}) (1 - D) T_s = 0 \implies V_{in} D - V_{out} D - V_{out} + V_{out} D = 0 \implies \mathbf{V_{out} = D \cdot V_{in}} ( V in ​ − V o u t ​ ) D T s ​ + ( − V o u t ​ ) ( 1 − D ) T s ​ = 0 ⟹ V in ​ D − V o u t ​ D − V o u t ​ + V o u t ​ D = 0 ⟹ V out ​ = D ⋅ V in ​

  • 2. Boost Converter (Step-Up) BOOST CONVERTER CIRCUIT TOPOLOGY
  • Inductor (L) Diode (D1)
  • +-----------[ZZZZ]-----+----------|>|---------+--------+ (+) V_out
  • | | | |
  • + | | | |
  • (~) V_in +--+--+ +---+ +---+
  • | | | Switch (Q1) | | C | | R_load
  • | +--+--+ +---+ +---+
  • | | | |
  • +----------------------+----------------------+--------+ (-) Common

Switch ON Interval ( 0 ≤ t ≤ D T s 0 \le t \le D T_s 0 ≤ t ≤ D T s ​ ): Q 1 Q_1 Q 1 ​ closed, D 1 D_1 D 1 ​ reverse-biased. Inductor connects directly across source: v L = V i n v_L = V_{in} v L ​ = V in ​ . Inductor stores magnetic energy ( Δ I L = V i n D T s L \Delta I_L = \frac{V_{in} D T_s}{L} Δ I L ​ = L V in ​ D T s ​ ​ ).

Switch OFF Interval ( D T s < t ≤ T s D T_s < t \le T_s D T s ​ < t ≤ T s ​ ): Q 1 Q_1 Q 1 ​ open, D 1 D_1 D 1 ​ conducts. Inductor discharges in series with source: v L = V i n − V o u t v_L = V_{in} - V_{out} v L ​ = V in ​ − V o u t ​ .

Volt-Second Balance Derivation: ( V i n ) D T s + ( V i n − V o u t ) ( 1 − D ) T s = 0 ⟹ V i n D + V i n − V o u t − V i n D + V o u t D = 0 (V_{in}) D T_s + (V_{in} - V_{out}) (1 - D) T_s = 0 \implies V_{in} D + V_{in} - V_{out} - V_{in} D + V_{out} D = 0 ( V in ​ ) D T s ​ + ( V in ​ − V o u t ​ ) ( 1 − D ) T s ​ = 0 ⟹ V in ​ D + V in ​ − V o u t ​ − V in ​ D + V o u t ​ D = 0 V i n = V o u t ( 1 − D ) ⟹ V o u t = V i n 1 − D V_{in} = V_{out} (1 - D) \implies \mathbf{V_{out} = \frac{V_{in}}{1 - D}} V in ​ = V o u t ​ ( 1 − D ) ⟹ V out ​ = 1 − D V in ​ ​

3. Buck-Boost Converter (Inverting Step-Up/Down)

Switch ON: v L = V i n v_L = V_{in} v L ​ = V in ​ ; Switch OFF: v L = V o u t v_L = V_{out} v L ​ = V o u t ​ (with reversed output polarity).

Voltage conversion: V o u t = − V i n D 1 − D V_{out} = -V_{in} \frac{D}{1 - D} V o u t ​ = − V in ​ 1 − D D ​ .

When D < 0.5 D < 0.5 D < 0.5 , ∣ V o u t ∣ < V i n |V_{out}| < V_{in} ∣ V o u t ​ ∣ < V in ​ (step-down).

When D > 0.5 D > 0.5 D > 0.5 , ∣ V o u t ∣ > V i n |V_{out}| > V_{in} ∣ V o u t ​ ∣ > V in ​ (step-up).

When D = 0.5 D = 0.5 D = 0.5 , ∣ V o u t ∣ = V i n |V_{out}| = V_{in} ∣ V o u t ​ ∣ = V in ​ .

3. Discontinuous Conduction Mode (DCM) & Boundary Conditions

When load current decreases (or load resistance R R R increases) such that the minimum inductor current hits zero before the end of the switching cycle, the converter enters Discontinuous Conduction Mode (DCM) . INDUCTOR CURRENT MODES OF OPERATION

  • Inductor Current (i_L)
  • ^
  • | /\ /\ /\
  • | / \ / \ / \ CONTINUOUS CONDUCTION MODE (CCM)
  • I_min +-----+----+------+----+------+----+----+ (i_L > 0 at all times)
  • | / \ / \ / \
  • 0---+--------+--+--------+--+--------+--> Time
  • |
  • | /\ /\ /\
  • | / \ / \ / \ DISCONTINUOUS CONDUCTION MODE (DCM)
  • 0-----+----+---+--+----+---+--+----+---+-> Time (i_L reaches zero and
  • |<-DT->| | stays at zero until next cycle)

Warning

DCM Voltage Regulation Loss: In DCM, the simple linear voltage conversion ratios ( V o u t = D V i n V_{out} = D V_{in} V o u t ​ = D V in ​ ) no longer hold! The output voltage becomes a non-linear function of load resistance R R R , inductance L L L , switching frequency f s w f_{sw} f s w ​ , and duty cycle D D D . At no load ( R → ∞ R \to \infty R → ∞ ), the output voltage in a Buck or Boost converter floats up to V i n V_{in} V in ​ or dangerously high levels unless clamped by a feedback control loop.

4. DC-to-AC Inverter Architectures

Inverters synthesize alternating AC voltage waveforms from a fixed DC source ( V d c V_{dc} V d c ​ ). Industrial systems deploy single-phase H-bridges and three-phase six-switch Voltage Source Inverters (VSI). THREE-PHASE VOLTAGE SOURCE INVERTER (VSI)

  • +--- (+) DC Bus (V_dc)
  • |
  • Q1 Q3 Q5
  • +--[ / ]--+--[ / ]--+--[ / ]--+
  • | | | |
  • | Phase A | Phase B | Phase C |
  • +----+ +----+ +----+ |
  • | | | | | | |
  • | +----+----+----+ | |
  • | | (Motor) | |
  • +--[ / ]--+--[ / ]--+--[ / ]--+
  • Q4 Q6 Q2
  • |
  • +--- (-) DC Bus Return
  • Six-Step ( 180 ∘ 180^\circ 18 0 ∘ Conduction) Inverter Mode

Each switch conducts for 180 ∘ 180^\circ 18 0 ∘ electrical degrees. The resulting line-to-line output voltage is a six-step waveform:

Total RMS Line-to-Line Voltage: V L L , r m s = 2 3 V d c ≈ 0.8165 ⋅ V d c V_{LL,rms} = \sqrt{\frac{2}{3}} V_{dc} \approx 0.8165 \cdot V_{dc} V LL , r m s ​ = 3 2 ​ ​ V d c ​ ≈ 0.8165 ⋅ V d c ​

Fundamental RMS Line-to-Line Voltage ( V L L 1 , r m s V_{LL1,rms} V LL 1 , r m s ​ ): V L L 1 , r m s = 6 π V d c ≈ 0.7797 ⋅ V d c V_{LL1,rms} = \frac{\sqrt{6}}{\pi} V_{dc} \approx 0.7797 \cdot V_{dc} V LL 1 , r m s ​ = π 6 ​ ​ V d c ​ ≈ 0.7797 ⋅ V d c ​

5. Sinusoidal Pulse-Width Modulation (SPWM)

To eliminate low-order harmonics and provide linear output voltage control, inverters use Sinusoidal PWM (SPWM) , comparing three low-frequency reference control sinusoids ( v c o n t r o l v_{control} v co n t ro l ​ ) against a high-frequency triangular carrier wave ( v t r i v_{tri} v t r i ​ ). SPWM MODULATION PRINCIPLE

  • Voltage
  • ^
  • +V_tri| /\ /\ /\ /\ /\ /\ /\ /\ /\ High-Frequency Triangle Carrier (f_sw)
  • | / \/ \/ \/ \/ \/ \/ \/ \/ \

| / .-'"""'-. / \ / \ .-'"""'-.

  • |/ / \ / \/ \ / \ Low-Frequency Sine Reference (f_fund)
  • V_tri+-----------------------------------------> Time
  • |
  • PWM | +---+ +-----+ +---+ +---+
  • Gate | | | | | | | | |
  • Out 0-+---+-------+-----+-----+---+-------+---+-> Time

SPWM Modulation Parameters:

Amplitude Modulation Index ( m a m_a m a ​ ): m a = V c o n t r o l , p k V t r i , p k m_a = \frac{V_{control,pk}}{V_{tri,pk}} m a ​ = V t r i , p k ​ V co n t ro l , p k ​ ​

Frequency Modulation Index ( m f m_f m f ​ ): m f = f t r i f c o n t r o l = f s w f 1 m_f = \frac{f_{tri}}{f_{control}} = \frac{f_{sw}}{f_1} m f ​ = f co n t ro l ​ f t r i ​ ​ = f 1 ​ f s w ​ ​ (For 3-phase systems, m f m_f m f ​ is chosen as an odd multiple of 3, e.g., 15 , 21 , 27 , 33 15, 21, 27, 33 15 , 21 , 27 , 33 , to cancel triplen harmonics in line-to-line voltages and eliminate even harmonics).

Linear Modulation Range ( 0 ≤ m a ≤ 1.0 0 \le m_a \le 1.0 0 ≤ m a ​ ≤ 1.0 )

In the linear region, the fundamental output voltage scales strictly proportionally with m a m_a m a ​ :

Fundamental Peak Line-to-Neutral Voltage: V L N 1 , p k = m a V d c 2 V_{LN1,pk} = m_a \frac{V_{dc}}{2} V L N 1 , p k ​ = m a ​ 2 V d c ​ ​

Fundamental RMS Line-to-Neutral Voltage: V L N 1 , r m s = m a V d c 2 2 ≈ 0.3535 ⋅ m a V d c V_{LN1,rms} = \frac{m_a V_{dc}}{2\sqrt{2}} \approx 0.3535 \cdot m_a V_{dc} V L N 1 , r m s ​ = 2 2 ​ m a ​ V d c ​ ​ ≈ 0.3535 ⋅ m a ​ V d c ​

Fundamental RMS Line-to-Line Voltage ( V L L 1 , r m s V_{LL1,rms} V LL 1 , r m s ​ ): V L L 1 , r m s = 3 ⋅ V L N 1 , r m s = 3 2 2 m a V d c = 6 4 m a V d c ≈ 0.61237 ⋅ m a V d c V_{LL1,rms} = \sqrt{3} \cdot V_{LN1,rms} = \frac{\sqrt{3}}{2\sqrt{2}} m_a V_{dc} = \frac{\sqrt{6}}{4} m_a V_{dc} \approx 0.61237 \cdot m_a V_{dc} V LL 1 , r m s ​ = 3 ​ ⋅ V L N 1 , r m s ​ = 2 2 ​ 3 ​ ​ m a ​ V d c ​ = 4 6 ​ ​ m a ​ V d c ​ ≈ 0.61237 ⋅ m a ​ V d c ​

Overmodulation ( 1.0 < m a ≤ 3.24 1.0 < m_a \le 3.24 1.0 < m a ​ ≤ 3.24 ) and Six-Step Limit

When m a > 1.0 m_a > 1.0 m a ​ > 1.0 , the sine wave peaks exceed the triangle carrier, causing pulse-dropping and harmonic distortion until the output degenerates into the square-wave six-step limit ( V L L 1 , r m s = 0.7797 V d c V_{LL1,rms} = 0.7797 V_{dc} V LL 1 , r m s ​ = 0.7797 V d c ​ ).

6. Space Vector PWM (SVPWM)

Space Vector PWM (SVPWM) treats the 3-phase inverter as a single unit with 8 possible discrete switching states ( V 0 [ 000 ] V_0 [000] V 0 ​ [ 000 ] to V 7 [ 111 ] V_7 [111] V 7 ​ [ 111 ] ), forming a hexagon in the complex α − β \alpha-\beta α − β stationary reference plane. SPACE VECTOR VOLTAGE HEXAGON (SVPWM)

  • V2 (010)
  • (120°)
  • +-----------+-----------+
  • / \ | / \
  • / \ Sector | Sector / \
  • / \ II | I / \
  • / \ | / \
  • V3 (011) + Sector \ | / Sector + V1 (100)
  • (180°) | III \ | / VI | (0°)
  • | \ | / |
  • |------------+-(0)-+------------| Reference Vector V_ref
  • | / | \ | rotates smoothly 360°
  • V4 (001) + Sector / | \ Sector + V6 (101)
  • (240°) \ IV / | \ V /
  • \ / | \ /
  • \ / Sector| Sector\ /
  • \ / III | IV \ /
  • +-----------+-----------+
  • V5 (001)
  • (300°)
  • (Zero Vectors: V0 [000], V7 [111])
  • The SVPWM DC-Bus Advantage

In standard SPWM, the maximum fundamental peak line-to-line voltage in the linear region is bounded by V d c V_{dc} V d c ​ . In SVPWM, the reference vector can reach the inner circle inscribed within the hexagon without overmodulation: V r e f , m a x = V d c 3 V_{ref,max} = \frac{V_{dc}}{\sqrt{3}} V re f , ma x ​ = 3 ​ V d c ​ ​ V L L 1 , r m s , m a x ( S V P W M ) = V d c 2 ≈ 0.7071 ⋅ V d c V_{LL1,rms,max(SVPWM)} = \frac{V_{dc}}{\sqrt{2}} \approx 0.7071 \cdot V_{dc} V LL 1 , r m s , ma x ( S V P W M ) ​ = 2 ​ V d c ​ ​ ≈ 0.7071 ⋅ V d c ​ Voltage Utilization Improvement Ratio: 0.7071 0.6124 = 2 3 ≈ 1.1547 ⟹ + 15.47 % Higher DC Bus Utilization \text{Voltage Utilization Improvement Ratio: } \frac{0.7071}{0.6124} = \frac{2}{\sqrt{3}} \approx 1.1547 \implies \mathbf{+15.47\% \text{ Higher DC Bus Utilization}} Voltage Utilization Improvement Ratio: 0.6124 0.7071 ​ = 3 ​ 2 ​ ≈ 1.1547 ⟹ + 15.47% Higher DC Bus Utilization

This 15.5 % 15.5\% 15.5% boost allows driving standard 460 V 460\text{ V} 460 V rated AC motors from a lower DC bus voltage ( 650 V 650\text{ V} 650 V instead of 751 V 751\text{ V} 751 V ), significantly lowering switch voltage ratings and inverter losses.

  • 7. Comprehensive Step-by-Step Worked Mathematical Example
  • Problem Statement

A solar PV and battery storage system utilizes a DC-DC Boost Converter feeding a 3-phase Voltage Source Inverter (VSI) to drive an industrial 3-phase water pump motor:

  • Boost Converter Input Voltage: V i n = 280.0 V DC V_{in} = 280.0\text{ V DC} V in ​ = 280.0 V DC
  • Boost Converter Switching Frequency: f s w = 25.0 kHz f_{sw} = 25.0\text{ kHz} f s w ​ = 25.0 kHz
  • Target Inverter DC Bus Voltage: V d c = 700.0 V DC V_{dc} = 700.0\text{ V DC} V d c ​ = 700.0 V DC
  • Full-Load DC Power Delivered: P o = 35.0 kW P_o = 35.0\text{ kW} P o ​ = 35.0 kW

Design Requirement 1: Inductor peak-to-peak ripple current must not exceed 20.0 % 20.0\% 20.0% of average input current ( Δ I L ≤ 0.20 I i n \Delta I_L \le 0.20 I_{in} Δ I L ​ ≤ 0.20 I in ​ ).

Design Requirement 2: DC bus output voltage ripple must not exceed 1.0 % 1.0\% 1.0% ( Δ V d c V d c ≤ 0.010 \frac{\Delta V_{dc}}{V_{dc}} \le 0.010 V d c ​ Δ V d c ​ ​ ≤ 0.010 ).

The 3-phase VSI drives the motor using linear Sinusoidal PWM (SPWM) with an amplitude modulation index of m a = 0.850 m_a = 0.850 m a ​ = 0.850 .

Calculate:

The required duty cycle ( D D D ) of the Boost converter in CCM.

The average input current ( I i n I_{in} I in ​ ) and the minimum required inductance ( L L L ) to satisfy the 20 % 20\% 20% ripple limit.

The minimum required DC bus filter capacitance ( C C C ) to satisfy the 1.0 % 1.0\% 1.0% voltage ripple limit.

The fundamental line-to-line RMS voltage ( V L L 1 , r m s V_{LL1,rms} V LL 1 , r m s ​ ) delivered to the motor terminals under SPWM.

The fundamental line-to-line RMS voltage ( V L L 1 , r m s , S V P W M V_{LL1,rms,SVPWM} V LL 1 , r m s , S V P W M ​ ) if the inverter is upgraded to Space Vector PWM (SVPWM) operating at maximum linear modulation ( m a = 1.0 m_a = 1.0 m a ​ = 1.0 ). =========================================================================================

CALCULATION WORKFLOW & DETAILED STEP-BY-STEP SOLUTION:

=========================================================================================

Step 1: Compute Required Boost Duty Cycle (D)

For a CCM Boost converter:

  • V_out = V_in / (1 - D)
  • 1 - D = V_in / V_out = 280.0 V / 700.0 V = 0.4000
  • D = 1.0 - 0.4000 = 0.6000 (60.0% duty cycle)

Step 2: Calculate Input Current and Minimum Boost Inductance (L)

Average DC output current:

I_out = P_o / V_out = 35,000 W / 700.0 V = 50.00 A

Average input inductor current (assuming 100% ideal efficiency):

  • I_in = P_o / V_in = 35,000 W / 280.0 V = 125.00 A
  • (Verification: I_in = I_out / (1 - D) = 50.0 A / 0.40 = 125.00 A)

Maximum allowable peak-to-peak inductor ripple current:

Delta_I_L = 0.20 * I_in = 0.20 * 125.00 A = 25.00 A

Inductance formula for Boost converter:

  • Delta_I_L = (V_in * D) / (f_sw * L)
  • L = (V_in * D) / (f_sw * Delta_I_L)
  • = (280.0 V * 0.6000) / (25,000 Hz * 25.00 A)
  • = 168.0 V / 625,000 A/s
  • = 0.0002688 H = 268.8 μH ≈ 269 μH

Critical Inductance for CCM Verification:

  • Equivalent load resistance: R = V_out / I_out = 700 V / 50 A = 14.0 ohms
  • L_min,crit = (D * (1 - D)^2 * R) / (2 * f_sw)
  • = (0.60 * (0.40)^2 * 14.0) / (2 * 25,000)
  • = (0.60 * 0.16 * 14.0) / 50,000
  • = 1.344 / 50,000 = 26.88 μH
  • Since L = 268.8 μH >> 26.88 μH, the converter operates deeply in CCM! (CONFIRMED)

Step 3: Calculate Minimum Filter Capacitance (C)

Output voltage ripple formula for Boost converter:

  • Delta_V_out / V_out = D / (R * C * f_sw)
  • C = D / (R * f_sw * (Delta_V_out / V_out))
  • = 0.6000 / (14.0 ohms * 25,000 Hz * 0.010)
  • = 0.6000 / 3,500
  • = 0.00017143 F = 171.43 μF ≈ 172 μF

Step 4: Compute Motor Terminal Voltage with SPWM (m_a = 0.850)

Fundamental line-to-line RMS voltage:

  • V_LL1,rms = (sqrt(3) / (2 * sqrt(2))) * m_a * V_dc
  • = 0.612372 * 0.850 * 700.0 V
  • = 0.612372 * 595.0 V
  • = 364.36 V ≈ 364.4 V

Step 5: Compute Motor Terminal Voltage with SVPWM (m_a = 1.0)

Fundamental line-to-line RMS voltage at maximum linear SVPWM:

  • V_LL1,rms,SVPWM = V_dc / sqrt(2)
  • = 700.0 V / 1.414214
  • = 494.97 V ≈ 495.0 V

Comparison with SPWM at m_a = 1.0:

  • V_LL1,rms,SPWM(m_a=1.0) = 0.612372 * 700.0 V = 428.66 V
  • SVPWM Voltage Advantage: 494.97 V / 428.66 V = 1.1547 (+15.47% increase!)
  • =========================================================================================
  • 8. Common PE Exam Traps & Tactical Pitfalls

Inverting the Duty Cycle Ratio in Boost Converters: Using V o u t = ( 1 − D ) V i n V_{out} = (1 - D) V_{in} V o u t ​ = ( 1 − D ) V in ​ instead of V o u t = V i n 1 − D V_{out} = \frac{V_{in}}{1 - D} V o u t ​ = 1 − D V in ​ ​ . Remember that as D → 1 D \to 1 D → 1 , Boost output voltage approaches infinity ( V o u t → ∞ V_{out} \to \infty V o u t ​ → ∞ ).

Applying Buck Voltage Ripple Equations to Boost Converters: The Buck converter has an inductor continuously connected to the output, yielding an 8-factor second-order filter equation ( Δ V / V = 1 − D 8 L C f 2 \Delta V / V = \frac{1-D}{8 L C f^2} Δ V / V = 8 L C f 2 1 − D ​ ). The Boost converter's inductor is disconnected from the output during the ON-interval, discharging the capacitor directly into the load ( Δ V / V = D R C f \Delta V / V = \frac{D}{R C f} Δ V / V = RC f D ​ ). Applying the Buck ripple formula to a Boost converter underestimates required capacitance by an order of magnitude!

Modulation Index Voltage Scaling Confusion ( V L N V_{LN} V L N ​ vs. V L L V_{LL} V LL ​ ): On the exam, remember:

Line-to-Neutral RMS: V L N 1 , r m s = m a V d c 2 2 ≈ 0.3535 m a V d c V_{LN1,rms} = \frac{m_a V_{dc}}{2\sqrt{2}} \approx 0.3535 m_a V_{dc} V L N 1 , r m s ​ = 2 2 ​ m a ​ V d c ​ ​ ≈ 0.3535 m a ​ V d c ​

Line-to-Line RMS: V L L 1 , r m s = 3 V L N 1 , r m s = 6 4 m a V d c ≈ 0.6124 m a V d c V_{LL1,rms} = \sqrt{3} V_{LN1,rms} = \frac{\sqrt{6}}{4} m_a V_{dc} \approx 0.6124 m_a V_{dc} V LL 1 , r m s ​ = 3 ​ V L N 1 , r m s ​ = 4 6 ​ ​ m a ​ V d c ​ ≈ 0.6124 m a ​ V d c ​

Neglecting Inverting Polarity in Buck-Boost Converters: The output voltage of a classic single-switch Buck-Boost converter has a negative potential relative to the common input rail ( V o u t = − V i n D 1 − D V_{out} = -V_{in} \frac{D}{1-D} V o u t ​ = − V in ​ 1 − D D ​ ).

Loading diagram... DC-DC and Inverter System Conversion Architecture