Study guide

2.2 Effective Stress & Pore Water Pressure Dynamics

PE Civil Geotechnical Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Site Characterization

1.1 Site Data Interpretation & Boring Plans 1.2 In Situ Testing & Field Exploration 1.3 Soil and Rock Classification Systems 1.4 Groundwater Characterization & Hydrogeology

2 Chapter 2: Soil Mechanics, Laboratory Testing, and Analysis

2.1 Weight-Volume Phase Relationships & Index Properties 2.2 Effective Stress & Pore Water Pressure Dynamics 2.3 Shear Strength Principles & Laboratory Testing 2.4 Permeability, Hydraulic Conductivity & Seepage Properties 2.5 Consolidation & Compressibility Analysis

3 Chapter 3: Construction Observation, Monitoring, QA/QC, and Safety

3.1 Earthwork Quality Control & Compaction Verification 3.2 Geotechnical Instrumentation & Field Monitoring 3.3 Trenching, Excavation Safety & OSHA Shoring Requirements 3.4 Erosion, Scour Protection & Slope Protection During Construction

4 Chapter 4: Earthquake Engineering and Dynamic Loads

4.1 Seismic Site Characterization & Ground Motion Hazards 4.2 Soil Liquefaction Triggering & Post-Liquefaction Assessment 4.3 Dynamic Soil Properties & Ground Response Analysis 4.4 Pseudostatic Analysis & Seismic Geotechnical Design

5 Chapter 5: Earth Structures, Ground Improvement, and Pavement

5.1 Slope Stability Analysis & Limit Equilibrium Methods 5.2 Embankments, Earth Dams & Levee Geotechnics 5.3 Ground Improvement Techniques & Design 5.4 Geosynthetics in Geotechnical Engineering 5.5 Flexible & Rigid Pavement Subgrades & Buried Utilities 5.6 Landfills, Caps & Containment Systems

6 Chapter 6: Groundwater and Seepage

6.1 Dewatering System Design & Well Drawdown 6.2 Flow Nets & Two-Dimensional Seepage Analysis 6.3 Uplift Pressure, Piping & Heave Safety 6.4 Subsurface Drainage Systems & Filter Criteria

7 Chapter 7: Problematic Soil and Rock Conditions

7.1 Expansive & Collapsible Soil Engineering 7.2 Organic Soils, Sensitive Clays & Soft Marine Deposits 7.3 Corrosive, Frost-Susceptible & Degradable Formations 7.4 Karst Topography, Rock Slopes & Rockfall Hazards

8 Chapter 8: Retaining Structures

8.1 Lateral Earth Pressure Theories 8.2 Rigid Retaining Wall Design 8.3 Flexible Retaining Walls & Sheet Pile Bulkheads 8.4 Temporary Support of Excavations 8.5 Mechanically Stabilized Earth (MSE) Walls & Soil Nail Structures 8.6 Cofferdams, Underpinning & Adjacent Infrastructure Effects

9 Chapter 9: Shallow Foundations

9.1 Ultimate & Allowable Bearing Capacity Theories 9.2 Effective Footing Area, Eccentricity & Combined Footings 9.3 Induced Stress Distribution & Immediate Elastic Settlement 9.4 Consolidation Settlement & Mat/Raft Foundation Design

10 Chapter 10: Deep Foundations

10.1 Driven Pile Axial Capacity & Settlement 10.2 Drilled Shaft Axial Design & Construction Methods 10.3 Lateral Load Behavior of Deep Foundations 10.4 Pile Group Dynamics, Efficiency & Downdrag 10.5 Dynamic Load Testing & Pile Integrity Evaluation

2.2 Effective Stress & Pore Water Pressure Dynamics

Key Takeaways Explain This Topic AI

Terzaghi's effective stress principle (σ' = σ - u) dictates that soil shear strength, volume change, and deformation depend exclusively on effective intergranular stress rather than total stress.

Hydrostatic pore pressure increases linearly below the water table (u = γw · zw), whereas vertical fluid seepage introduces dynamic pore pressure alterations that alter effective stresses.

Upward hydraulic gradient exceeding the critical hydraulic gradient (icr = γ' / γw) results in zero effective stress (σ' = 0), inducing quicksand conditions and piping failure.

Capillary action above the water table generates negative pore pressure (suction), increasing effective stress and providing apparent cohesion to unsaturated fine and coarse soils.

Geotechnical effective stress profiles must rigorously integrate layered stratigraphy, surface surcharges, buoyant unit weights, and transient or steady-state hydraulic gradients.

Last updated: July 2026

  • 2.2 Effective Stress & Pore Water Pressure Dynamics
  • 1. Terzaghi’s Effective Stress Principle

In 1923, Karl Terzaghi established the foundational framework of modern soil mechanics by identifying that soil behavior is governed not by total overburden pressure, but by the stress transferred through the solid mineral matrix.

The Effective Stress Equation: σ ′ = σ − u \sigma' = \sigma - u σ ′ = σ − u

Where:

σ \sigma σ : Total normal stress acting on a plane within the soil mass.

σ ′ \sigma' σ ′ : Effective normal stress (intergranular stress carried by solid skeleton contacts).

u u u : Pore water pressure acting in all directions within the fluid-filled void space.

Key Physical Consequences:

Shear Strength Control: Water has zero shear resistance. Therefore, the shear strength of soil depends strictly on effective normal stress: τ f = c ′ + σ ′ tan ⁡ ϕ ′ = c ′ + ( σ − u ) tan ⁡ ϕ ′ \tau_f = c' + \sigma' \tan\phi' = c' + (\sigma - u) \tan\phi' τ f ​ = c ′ + σ ′ tan ϕ ′ = c ′ + ( σ − u ) tan ϕ ′

Volume Change and Settlement: Soil compression occurs due to the rearrangement of mineral grains, which is driven entirely by changes in effective stress ( Δ σ ′ \Delta\sigma' Δ σ ′ ). An increase in total stress σ \sigma σ accompanied by an equal increase in pore pressure u u u results in zero effective stress change ( Δ σ ′ = 0 \Delta\sigma' = 0 Δ σ ′ = 0 ) and zero consolidation settlement.

2. Total Stress and Pore Pressure in Layered Soil Stratigraphy

To evaluate effective stress at a depth z z z below the ground surface, the total vertical stress and hydrostatic pore pressure are summed across soil layers:

Total Vertical Stress ( σ v \sigma_v σ v ​ ): σ v = ∑ i = 1 n γ i ⋅ h i + q \sigma_v = \sum_{i=1}^{n} \gamma_i \cdot h_i + q σ v ​ = i = 1 ∑ n ​ γ i ​ ⋅ h i ​ + q

Where γ i \gamma_i γ i ​ and h i h_i h i ​ are the total unit weight and thickness of layer i i i , and q q q is an applied surface surcharge load.

Hydrostatic Pore Water Pressure ( u u u ):

For static ground water conditions (no vertical seepage): ν = { 0 & above the water table (ignoring capillarity) γ w ⋅ z w & at depth z w below the phreatic surface \nu = \begin{cases} 0 \& \text{above the water table (ignoring capillarity)} \ \gamma_w \cdot z_w \& \text{at depth } z_w \text{ below the phreatic surface} \end{cases} ν = { 0& above the water table (ignoring capillarity) γ w ​ ⋅ z w ​ & at depth z w ​ below the phreatic surface ​

Effective Vertical Stress ( σ v ′ \sigma'_v σ v ′ ​ ): σ v ′ = σ v − u \sigma'_v = \sigma_v - u σ v ′ ​ = σ v ​ − u

In fully submerged soil layers under static conditions, effective stress can be directly computed using the submerged unit weight ( γ ′ = γ s a t − γ w \gamma' = \gamma_{sat} - \gamma_w γ ′ = γ s a t ​ − γ w ​ ): σ v ′ = ∑ γ d r y / m o i s t ⋅ h a b o v e W T + ∑ γ ′ ⋅ h b e l o w W T + q \sigma'_v = \sum \gamma_{dry/moist} \cdot h_{above\,WT} + \sum \gamma' \cdot h_{below\,WT} + q σ v ′ ​ = ∑ γ d ry / m o i s t ​ ⋅ h ab o v e W T ​ + ∑ γ ′ ⋅ h b e l o w W T ​ + q

3. Seepage Forces and Dynamic Pore Pressure Dynamics

When water flows through soil, viscous drag forces are transferred from the fluid to the soil skeleton. This fluid-solid interaction alters the pore pressure distribution and effective stress state.

Consider one-dimensional vertical flow through a soil column of length L L L under a total head loss Δ h \Delta h Δ h :

The hydraulic gradient is i = Δ h L i = \frac{\Delta h}{L} i = L Δ h ​ .

Case A: Downward Vertical Seepage

Downward flow exerts a drag force in the direction of gravity, increasing effective stress:

  • Seepage force per unit volume: j = i ⋅ γ w j = i \cdot \gamma_w j = i ⋅ γ w ​ (acting downward)
  • Pore pressure at depth z z z : u = γ w z − i z γ w u = \gamma_w z - i z \gamma_w u = γ w ​ z − i z γ w ​

Effective stress at depth z z z : σ v ′ = γ ′ z + i z γ w = ( γ ′ + i γ w ) z \sigma'_v = \gamma' z + i z \gamma_w = (\gamma' + i \gamma_w) z σ v ′ ​ = γ ′ z + i z γ w ​ = ( γ ′ + i γ w ​ ) z

Case B: Upward Vertical Seepage

Upward flow exerts a drag force opposing gravity, reducing effective stress:

Pore pressure at depth z z z : u = γ w z + i z γ w u = \gamma_w z + i z \gamma_w u = γ w ​ z + i z γ w ​

Effective stress at depth z z z : σ v ′ = γ ′ z − i z γ w = ( γ ′ − i γ w ) z \sigma'_v = \gamma' z - i z \gamma_w = (\gamma' - i \gamma_w) z σ v ′ ​ = γ ′ z − i z γ w ​ = ( γ ′ − i γ w ​ ) z

4. Critical Hydraulic Gradient ( i c r i_{cr} i cr ​ ) & Quicksand / Boiling

In upward seepage, if the upward hydraulic gradient i i i increases to the point where effective stress becomes zero ( σ v ′ = 0 \sigma'_v = 0 σ v ′ ​ = 0 ): σ v ′ = ( γ ′ − i c r γ w ) z = 0 ⟹ i c r = γ ′ γ w \sigma'_v = (\gamma' - i_{cr} \gamma_w) z = 0 \implies i_{cr} = \frac{\gamma'}{\gamma_w} σ v ′ ​ = ( γ ′ − i cr ​ γ w ​ ) z = 0 ⟹ i cr ​ = γ w ​ γ ′ ​

Substituting γ ′ = G s − 1 1 + e γ w \gamma' = \frac{G_s - 1}{1 + e} \gamma_w γ ′ = 1 + e G s ​ − 1 ​ γ w ​ : ∋ c r = G s − 1 1 + e \ni_{cr} = \frac{G_s - 1}{1 + e} ∋ cr ​ = 1 + e G s ​ − 1 ​

Engineering Implications:

For typical soils ( G s ≈ 2.65 , e ≈ 0.65 G_s \approx 2.65, e \approx 0.65 G s ​ ≈ 2.65 , e ≈ 0.65 ), i c r ≈ 1.65 1.65 = 1.0 i_{cr} \approx \frac{1.65}{1.65} = 1.0 i cr ​ ≈ 1.65 1.65 ​ = 1.0 .

When i ≥ i c r i \ge i_{cr} i ≥ i cr ​ , coarse cohesionless soils completely lose shear strength ( τ f = 0 ⋅ tan ⁡ ϕ ′ = 0 \tau_f = 0 \cdot \tan\phi' = 0 τ f ​ = 0 ⋅ tan ϕ ′ = 0 ), behaving as a heavy liquid. This phenomenon is termed quicksand , boiling , or heave .

The factor of safety against quicksand / piping instability is defined as: F S p i p i n g = i c r i e x i t FS_{piping} = \frac{i_{cr}}{i_{exit}} F S p i p in g ​ = i e x i t ​ i cr ​ ​ A minimum factor of safety of F S ≥ 3.0 to 4.0 FS \ge 3.0 \text{ to } 4.0 FS ≥ 3.0 to 4.0 is mandatory in geotechnical design for excavation support and dam foundations.

5. Capillary Rise & Unsaturated Negative Pore Pressure

Above the phreatic surface (water table), capillary tension draws water upward into soil pores.

Capillary Height ( h c h_c h c ​ ): h c = C e ⋅ D 10 h_c = \frac{C}{e \cdot D_{10}} h c ​ = e ⋅ D 10 ​ C ​

Where C C C is an empirical constant ( 10 − 50 mm 2 10 - 50 \text{ mm}^2 10 − 50 mm 2 ).

Pore Pressure in Capillary Zone:

Water in the capillary zone is under tension, resulting in negative pore water pressure (matric suction): ν = − S ⋅ γ w ⋅ h c \nu = - S \cdot \gamma_w \cdot h_c ν = − S ⋅ γ w ​ ⋅ h c ​

Where S S S is the degree of saturation in the capillary fringe ( S ≈ 1.0 S \approx 1.0 S ≈ 1.0 in fully saturated capillary zone, tapering off above).

Effective Stress Increase:

Because u u u is negative ( u < 0 u < 0 u < 0 ): σ ′ = σ − ( − u ) = σ + ∣ u ∣ \sigma' = \sigma - (-u) = \sigma + |u| σ ′ = σ − ( − u ) = σ + ∣ u ∣

Capillary suction increases effective stress and imparts apparent cohesion ( c a p p = ∣ u ∣ tan ⁡ ϕ ′ c_{app} = |u| \tan\phi' c a pp ​ = ∣ u ∣ tan ϕ ′ ). This allows vertical cuts in moist sand to stand temporarily. However, inundation saturates the soil ( u → 0 u \to 0 u → 0 ), destroying apparent cohesion and causing collapse.

6. Comprehensive Worked Example

Problem Profile: Consider a soil profile with three layers:

Layer 1 (0 to 3.0 m): Moist sand above water table, γ = 18.0 kN/m 3 \gamma = 18.0 \text{ kN/m}^3 γ = 18.0 kN/m 3 .

Capillary Fringe (2.0 m to 3.0 m): Saturated capillary zone, γ = 19.0 kN/m 3 \gamma = 19.0 \text{ kN/m}^3 γ = 19.0 kN/m 3 , full capillary rise h c = 1.0 m h_c = 1.0 \text{ m} h c ​ = 1.0 m above WT. Water table located at depth z = 3.0 m z = 3.0 \text{ m} z = 3.0 m .

Layer 2 (3.0 to 8.0 m): Saturated clay below water table, γ s a t = 20.0 kN/m 3 \gamma_{sat} = 20.0 \text{ kN/m}^3 γ s a t ​ = 20.0 kN/m 3 .

A uniform surface surcharge q = 25 kPa q = 25 \text{ kPa} q = 25 kPa is applied at ground surface.

Calculate total stress σ \sigma σ , pore pressure u u u , and effective stress σ ′ \sigma' σ ′ at:

  • Ground surface ( z = 0 z = 0 z = 0 )
  • Top of capillary zone ( z = 2.0 m z = 2.0 \text{ m} z = 2.0 m )
  • Water table level ( z = 3.0 m z = 3.0 \text{ m} z = 3.0 m )
  • Bottom of clay layer ( z = 8.0 m z = 8.0 \text{ m} z = 8.0 m )

Detailed Solution:

At z = 0 m z = 0 \text{ m} z = 0 m (Ground Surface):

  • Total stress: σ = q = 25.0 kPa \sigma = q = 25.0 \text{ kPa} σ = q = 25.0 kPa
  • Pore pressure: u = 0 kPa u = 0 \text{ kPa} u = 0 kPa
  • Effective stress: σ ′ = 25.0 − 0 = 25.0 kPa \sigma' = 25.0 - 0 = 25.0 \text{ kPa} σ ′ = 25.0 − 0 = 25.0 kPa

At z = 2.0 m z = 2.0 \text{ m} z = 2.0 m (Top of Capillary Fringe, 1.0 m 1.0\text{ m} 1.0 m above WT):

Total stress: σ = q + γ l a y e r 1 ⋅ 2.0 = 25.0 + ( 18.0 × 2.0 ) = 61.0 kPa \sigma = q + \gamma_{layer1} \cdot 2.0 = 25.0 + (18.0 \times 2.0) = 61.0 \text{ kPa} σ = q + γ l a yer 1 ​ ⋅ 2.0 = 25.0 + ( 18.0 × 2.0 ) = 61.0 kPa

Pore pressure (capillary suction, h c = 1.0 m h_c = 1.0 \text{ m} h c ​ = 1.0 m ): u = − γ w ⋅ h c = − 9.81 × 1.0 = − 9.81 kPa u = -\gamma_w \cdot h_c = -9.81 \times 1.0 = -9.81 \text{ kPa} u = − γ w ​ ⋅ h c ​ = − 9.81 × 1.0 = − 9.81 kPa

Effective stress: σ ′ = σ − u = 61.0 − ( − 9.81 ) = 70.81 kPa \sigma' = \sigma - u = 61.0 - (-9.81) = 70.81 \text{ kPa} σ ′ = σ − u = 61.0 − ( − 9.81 ) = 70.81 kPa

At z = 3.0 m z = 3.0 \text{ m} z = 3.0 m (Water Table Level):

Total stress: σ = 61.0 + ( γ c a p ⋅ 1.0 ) = 61.0 + ( 19.0 × 1.0 ) = 80.0 kPa \sigma = 61.0 + (\gamma_{cap} \cdot 1.0) = 61.0 + (19.0 \times 1.0) = 80.0 \text{ kPa} σ = 61.0 + ( γ c a p ​ ⋅ 1.0 ) = 61.0 + ( 19.0 × 1.0 ) = 80.0 kPa

  • Pore pressure: u = 0 kPa u = 0 \text{ kPa} u = 0 kPa (at phreatic surface)
  • Effective stress: σ ′ = 80.0 − 0 = 80.0 kPa \sigma' = 80.0 - 0 = 80.0 \text{ kPa} σ ′ = 80.0 − 0 = 80.0 kPa

At z = 8.0 m z = 8.0 \text{ m} z = 8.0 m (Bottom of Layer 2, 5.0 m 5.0\text{ m} 5.0 m below WT):

Total stress: σ = 80.0 + ( γ s a t , c l a y ⋅ 5.0 ) = 80.0 + ( 20.0 × 5.0 ) = 180.0 kPa \sigma = 80.0 + (\gamma_{sat,clay} \cdot 5.0) = 80.0 + (20.0 \times 5.0) = 180.0 \text{ kPa} σ = 80.0 + ( γ s a t , c l a y ​ ⋅ 5.0 ) = 80.0 + ( 20.0 × 5.0 ) = 180.0 kPa

Pore pressure ( z w = 5.0 m z_w = 5.0 \text{ m} z w ​ = 5.0 m ): u = γ w ⋅ z w = 9.81 × 5.0 = 49.05 kPa u = \gamma_w \cdot z_w = 9.81 \times 5.0 = 49.05 \text{ kPa} u = γ w ​ ⋅ z w ​ = 9.81 × 5.0 = 49.05 kPa

Effective stress: σ ′ = σ − u = 180.0 − 49.05 = 130.95 kPa \sigma' = \sigma - u = 180.0 - 49.05 = 130.95 \text{ kPa} σ ′ = σ − u = 180.0 − 49.05 = 130.95 kPa

Check using submerged unit weight ( γ ′ = 20.0 − 9.81 = 10.19 kN/m 3 \gamma' = 20.0 - 9.81 = 10.19 \text{ kN/m}^3 γ ′ = 20.0 − 9.81 = 10.19 kN/m 3 ): σ ′ = 25.0 + ( 18.0 × 2.0 ) + ( 19.0 × 1.0 ) + ( 10.19 × 5.0 ) = 25.0 + 36.0 + 19.0 + 50.95 = 130.95 kPa ✓ \sigma' = 25.0 + (18.0 \times 2.0) + (19.0 \times 1.0) + (10.19 \times 5.0) = 25.0 + 36.0 + 19.0 + 50.95 = 130.95 \text{ kPa} \quad \checkmark σ ′ = 25.0 + ( 18.0 × 2.0 ) + ( 19.0 × 1.0 ) + ( 10.19 × 5.0 ) = 25.0 + 36.0 + 19.0 + 50.95 = 130.95 kPa ✓

Loading diagram... Stress Profiles with Depth (Total Stress, Pore Pressure, Effective Stress)