Study guide

2.3 Shear Strength Principles & Laboratory Testing

PE Civil Geotechnical Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Site Characterization

1.1 Site Data Interpretation & Boring Plans 1.2 In Situ Testing & Field Exploration 1.3 Soil and Rock Classification Systems 1.4 Groundwater Characterization & Hydrogeology

2 Chapter 2: Soil Mechanics, Laboratory Testing, and Analysis

2.1 Weight-Volume Phase Relationships & Index Properties 2.2 Effective Stress & Pore Water Pressure Dynamics 2.3 Shear Strength Principles & Laboratory Testing 2.4 Permeability, Hydraulic Conductivity & Seepage Properties 2.5 Consolidation & Compressibility Analysis

3 Chapter 3: Construction Observation, Monitoring, QA/QC, and Safety

3.1 Earthwork Quality Control & Compaction Verification 3.2 Geotechnical Instrumentation & Field Monitoring 3.3 Trenching, Excavation Safety & OSHA Shoring Requirements 3.4 Erosion, Scour Protection & Slope Protection During Construction

4 Chapter 4: Earthquake Engineering and Dynamic Loads

4.1 Seismic Site Characterization & Ground Motion Hazards 4.2 Soil Liquefaction Triggering & Post-Liquefaction Assessment 4.3 Dynamic Soil Properties & Ground Response Analysis 4.4 Pseudostatic Analysis & Seismic Geotechnical Design

5 Chapter 5: Earth Structures, Ground Improvement, and Pavement

5.1 Slope Stability Analysis & Limit Equilibrium Methods 5.2 Embankments, Earth Dams & Levee Geotechnics 5.3 Ground Improvement Techniques & Design 5.4 Geosynthetics in Geotechnical Engineering 5.5 Flexible & Rigid Pavement Subgrades & Buried Utilities 5.6 Landfills, Caps & Containment Systems

6 Chapter 6: Groundwater and Seepage

6.1 Dewatering System Design & Well Drawdown 6.2 Flow Nets & Two-Dimensional Seepage Analysis 6.3 Uplift Pressure, Piping & Heave Safety 6.4 Subsurface Drainage Systems & Filter Criteria

7 Chapter 7: Problematic Soil and Rock Conditions

7.1 Expansive & Collapsible Soil Engineering 7.2 Organic Soils, Sensitive Clays & Soft Marine Deposits 7.3 Corrosive, Frost-Susceptible & Degradable Formations 7.4 Karst Topography, Rock Slopes & Rockfall Hazards

8 Chapter 8: Retaining Structures

8.1 Lateral Earth Pressure Theories 8.2 Rigid Retaining Wall Design 8.3 Flexible Retaining Walls & Sheet Pile Bulkheads 8.4 Temporary Support of Excavations 8.5 Mechanically Stabilized Earth (MSE) Walls & Soil Nail Structures 8.6 Cofferdams, Underpinning & Adjacent Infrastructure Effects

9 Chapter 9: Shallow Foundations

9.1 Ultimate & Allowable Bearing Capacity Theories 9.2 Effective Footing Area, Eccentricity & Combined Footings 9.3 Induced Stress Distribution & Immediate Elastic Settlement 9.4 Consolidation Settlement & Mat/Raft Foundation Design

10 Chapter 10: Deep Foundations

10.1 Driven Pile Axial Capacity & Settlement 10.2 Drilled Shaft Axial Design & Construction Methods 10.3 Lateral Load Behavior of Deep Foundations 10.4 Pile Group Dynamics, Efficiency & Downdrag 10.5 Dynamic Load Testing & Pile Integrity Evaluation

2.3 Shear Strength Principles & Laboratory Testing

Key Takeaways Explain This Topic AI

The Mohr-Coulomb failure criterion defines soil shear strength as τf = c' + σ' tan φ', governed by effective cohesion (c') and effective friction angle (φ').

Direct Shear Testing (DST) provides rapid drained strength parameters on horizontal failure planes, whereas Unconfined Compression (UC) tests give quick undrained shear strength (Su = qu / 2) for saturated clays.

Triaxial testing variants (UU, CU, CD) simulate distinct field drainage conditions; CU testing with pore pressure measurement yields both total (c, φ) and effective (c', φ') strength parameters.

Cohesionless soils exhibit contractive (loose sand) or dilative (dense sand) volumetric response during shear, converging toward a critical state void ratio (ecrit).

Stress path representation in p'-q space converts circular failure envelopes into linear relations (q = a' + p' tan α'), facilitating continuous stress evolution tracking during loading.

Last updated: July 2026

  • 2.3 Shear Strength Principles & Laboratory Testing
  • 1. Mohr-Coulomb Failure Criterion

The shear strength of soil ( τ f \tau_f τ f ​ ) is the maximum resistance per unit area that a soil mass can offer against sliding along an internal failure surface under applied stress.

Effective Stress Form of Mohr-Coulomb Criterion: τ f = c ′ + σ ′ tan ⁡ ϕ ′ = c ′ + ( σ − u ) tan ⁡ ϕ ′ \tau_f = c' + \sigma' \tan\phi' = c' + (\sigma - u) \tan\phi' τ f ​ = c ′ + σ ′ tan ϕ ′ = c ′ + ( σ − u ) tan ϕ ′

Where:

c ′ c' c ′ : Effective cohesion intercept (interparticle chemical bonding or cementation).

ϕ ′ \phi' ϕ ′ : Effective angle of internal friction (interlocking and mineral friction).

σ ′ \sigma' σ ′ : Effective normal stress acting on the failure plane.

Principal Stresses at Failure

In Mohr's circle of stress, failure occurs when the circle becomes tangent to the Mohr-Coulomb envelope. The major ( σ 1 ′ \sigma'_1 σ 1 ′ ​ ) and minor ( σ 3 ′ \sigma'_3 σ 3 ′ ​ ) effective principal stresses at failure satisfy: σ 1 ′ = σ 3 ′ tan ⁡ 2 ( 45 ∘ + ϕ ′ 2 ) + 2 c ′ tan ⁡ ( 45 ∘ + ϕ ′ 2 ) = σ 3 ′ N ϕ + 2 c ′ N ϕ \sigma'_1 = \sigma'_3 \tan^2\left(45^\circ + \frac{\phi'}{2}\right) + 2 c' \tan\left(45^\circ + \frac{\phi'}{2}\right) = \sigma'_3 N_\phi + 2 c' \sqrt{N_\phi} σ 1 ′ ​ = σ 3 ′ ​ tan 2 ( 4 5 ∘ + 2 ϕ ′ ​ ) + 2 c ′ tan ( 4 5 ∘ + 2 ϕ ′ ​ ) = σ 3 ′ ​ N ϕ ​ + 2 c ′ N ϕ ​ ​

Where N ϕ = tan ⁡ 2 ( 45 ∘ + ϕ ′ 2 ) = 1 + sin ⁡ ϕ ′ 1 − sin ⁡ ϕ ′ N_\phi = \tan^2\left(45^\circ + \frac{\phi'}{2}\right) = \frac{1 + \sin\phi'}{1 - \sin\phi'} N ϕ ​ = tan 2 ( 4 5 ∘ + 2 ϕ ′ ​ ) = 1 − s i n ϕ ′ 1 + s i n ϕ ′ ​ .

Failure Plane Orientation

The failure plane is inclined at an angle θ \theta θ relative to the major principal stress plane (the horizontal plane when vertical stress is major): θ = 45 ∘ + ϕ ′ 2 \theta = 45^\circ + \frac{\phi'}{2} θ = 4 5 ∘ + 2 ϕ ′ ​

2. Laboratory Shear Strength Testing Methods

Test Method Specimen Drainage & State Measured Parameters Key Advantages / Limitations

Direct Shear Test (DST) Drained shear along a predetermined horizontal plane. Drained parameters ( c ′ , ϕ ′ c', \phi' c ′ , ϕ ′ ). Simple, fast; forced failure plane, non-uniform stress/strain distribution.

Unconfined Compression (UC) Undrained compression ( σ 3 = 0 \sigma_3 = 0 σ 3 ​ = 0 ), fast loading of saturated clay. Unconfined strength q u q_u q u ​ ; S u = c u = q u / 2 S_u = c_u = q_u / 2 S u ​ = c u ​ = q u ​ /2 . Quick, economical; only valid for saturated cohesive soils ( ϕ u = 0 \phi_u = 0 ϕ u ​ = 0 ).

Triaxial (UU) Unconsolidated-Undrained: no consolidation under σ 3 \sigma_3 σ 3 ​ , no drainage during shear. Undrained shear strength S u = c u S_u = c_u S u ​ = c u ​ ( ϕ u = 0 \phi_u = 0 ϕ u ​ = 0 ). Simulates end-of-construction short-term loading in saturated soft clays.

Triaxial (CU) Consolidated-Undrained: isotropic consolidation under σ 3 \sigma_3 σ 3 ​ , sheared undrained with u u u measured. Total ( c , ϕ c, \phi c , ϕ ) and effective ( c ′ , ϕ ′ c', \phi' c ′ , ϕ ′ ) parameters. Measures pore pressures ( u u u ); simulates rapid drawdown or post-consolidation loading.

Triaxial (CD) Consolidated-Drained: full consolidation under σ 3 \sigma_3 σ 3 ​ , sheared slowly ( u = 0 u = 0 u = 0 ). Drained parameters ( c ′ , ϕ ′ c', \phi' c ′ , ϕ ′ ). Simulates long-term steady-state stability of slopes and retaining walls.

3. Detailed Triaxial Testing Framework

A cylindrical soil specimen ( H : D = 2 : 1 H:D = 2:1 H : D = 2 : 1 ) is encased in a rubber membrane, placed in a pressurized chamber ( σ 3 \sigma_3 σ 3 ​ ), and loaded axially by a piston ( Δ σ = σ 1 − σ 3 \Delta\sigma = \sigma_1 - \sigma_3 Δ σ = σ 1 ​ − σ 3 ​ , termed the deviator stress ).

Unconsolidated-Undrained (UU / Total Stress) Test

Cell pressure σ 3 \sigma_3 σ 3 ​ applied with drainage closed.

Axial deviator stress Δ σ \Delta\sigma Δ σ increased to failure with drainage closed.

For fully saturated soils ( S = 100 % S = 100\% S = 100% ), increasing σ 3 \sigma_3 σ 3 ​ causes an equal pore pressure increase ( Δ u = Δ σ 3 \Delta u = \Delta\sigma_3 Δ u = Δ σ 3 ​ ). Consequently, effective principal stress remains unchanged.

Mohr circles of total stress at failure for various σ 3 \sigma_3 σ 3 ​ have identical diameters ( Δ σ f \Delta\sigma_f Δ σ f ​ ).

Total stress envelope is horizontal: ϕ u = 0 and τ f = c u = S u = σ 1 , f − σ 3 , f 2 \phi_u = 0 \quad \text{and} \quad \tau_f = c_u = S_u = \frac{\sigma_{1,f} - \sigma_{3,f}}{2} ϕ u ​ = 0 and τ f ​ = c u ​ = S u ​ = 2 σ 1 , f ​ − σ 3 , f ​ ​

Consolidated-Undrained (CU) Test with Pore Pressure Measurement

Specimen consolidated under cell pressure σ 3 \sigma_3 σ 3 ​ with drainage open ( u → 0 u \to 0 u → 0 ).

Drainage valves closed, axial load applied to failure while measuring excess pore pressure u f u_f u f ​ .

Effective principal stresses at failure: σ 3 ′ = σ 3 − u f and σ 1 ′ = σ 1 − u f = σ 3 + Δ σ f − u f \sigma'_3 = \sigma_3 - u_f \quad \text{and} \quad \sigma'_1 = \sigma_1 - u_f = \sigma_3 + \Delta\sigma_f - u_f σ 3 ′ ​ = σ 3 ​ − u f ​ and σ 1 ′ ​ = σ 1 ​ − u f ​ = σ 3 ​ + Δ σ f ​ − u f ​

Allows determination of both total parameters ( c , ϕ c, \phi c , ϕ ) and effective parameters ( c ′ , ϕ ′ c', \phi' c ′ , ϕ ′ ).

Skempton's Pore Pressure Parameters: Δ u = B [ Δ σ 3 + A ( Δ σ 1 − Δ σ 3 ) ] \Delta u = B \left[ \Delta\sigma_3 + A (\Delta\sigma_1 - \Delta\sigma_3) \right] Δ u = B [ Δ σ 3 ​ + A ( Δ σ 1 ​ − Δ σ 3 ​ ) ]

For saturated soils, B = 1.0 B = 1.0 B = 1.0 .

Parameter A A A at failure ( A f A_f A f ​ ): A f < 0 A_f < 0 A f ​ < 0 (heavily overconsolidated/dilative), A f = 0.5 − 1.0 A_f = 0.5 - 1.0 A f ​ = 0.5 − 1.0 (normally consolidated clay), A f > 1.0 A_f > 1.0 A f ​ > 1.0 (sensitive/collapsible clay).

Consolidated-Drained (CD) Test

Specimen fully consolidated under σ 3 \sigma_3 σ 3 ​ .

Axial shearing performed at an extremely slow strain rate to ensure u ≈ 0 u \approx 0 u ≈ 0 throughout.

Total stresses equal effective stresses ( σ 1 = σ 1 ′ , σ 3 = σ 3 ′ \sigma_1 = \sigma'_1, \sigma_3 = \sigma'_3 σ 1 ​ = σ 1 ′ ​ , σ 3 ​ = σ 3 ′ ​ ).

For normally consolidated clays and clean sands, effective cohesion is zero ( c ′ = 0 c' = 0 c ′ = 0 ).

  • 4. Drained vs. Undrained Soil Response & Critical State Concept
  • Granular Soil Behavior (Sands)

Loose Sand: Contractive during shear (volume decreases), generating positive pore pressure in undrained loading. Reaches peak strength smoothly.

Dense Sand: Dilative during shear (volume expands due to particle interlocking), generating negative pore pressure in undrained loading. Exhibits sharp peak strength followed by strain softening to critical state.

Critical State: At large shear strains, all specimens reach the critical state void ratio ( e c r i t e_{crit} e cr i t ​ ) where continuous shearing occurs at constant volume and constant shear stress without further volume change.

Fine-Grained Soil Behavior (Clays)

Normally Consolidated Clay ( O C R = 1 OCR = 1 OCR = 1 ): Contractive behavior, positive A f A_f A f ​ , c ′ ≈ 0 c' \approx 0 c ′ ≈ 0 .

Overconsolidated Clay ( O C R > 4 − 8 OCR > 4-8 OCR > 4 − 8 ): Dilative behavior, negative A f A_f A f ​ , exhibits true/apparent effective cohesion c ′ > 0 c' > 0 c ′ > 0 .

5. Stress Paths in p ′ − q p'-q p ′ − q Space

To track continuous stress states during testing without drawing multiple Mohr circles, stress paths plot invariant stress parameters: p ′ = σ 1 ′ + σ 3 ′ 2 and q = σ 1 ′ − σ 3 ′ 2 = Δ σ 2 p' = \frac{\sigma'_1 + \sigma'_3}{2} \quad \text{and} \quad q = \frac{\sigma'_1 - \sigma'_3}{2} = \frac{\Delta\sigma}{2} p ′ = 2 σ 1 ′ ​ + σ 3 ′ ​ ​ and q = 2 σ 1 ′ ​ − σ 3 ′ ​ ​ = 2 Δ σ ​

The failure line in p ′ − q p'-q p ′ − q space is defined by: q = a ′ + p ′ tan ⁡ α ′ q = a' + p' \tan\alpha' q = a ′ + p ′ tan α ′

Converting a ′ a' a ′ and α ′ \alpha' α ′ to Mohr-Coulomb parameters c ′ c' c ′ and ϕ ′ \phi' ϕ ′ : sin ⁡ ϕ ′ = tan ⁡ α ′ ⟺ ϕ ′ = arcsin ⁡ ( tan ⁡ α ′ ) \sin\phi' = \tan\alpha' \quad \Longleftrightarrow \quad \phi' = \arcsin(\tan\alpha') sin ϕ ′ = tan α ′ ⟺ ϕ ′ = arcsin ( tan α ′ ) c ′ = a ′ cos ⁡ ϕ ′ c' = \frac{a'}{\cos\phi'} c ′ = cos ϕ ′ a ′ ​

6. Comprehensive Worked Example

Problem Statement: A Consolidated-Undrained (CU) triaxial compression test with pore pressure measurement was conducted on a saturated normally consolidated clay ( c ′ = 0 c' = 0 c ′ = 0 ). The test results at failure are:

  • Chamber cell pressure: σ 3 = 200 kPa \sigma_3 = 200 \text{ kPa} σ 3 ​ = 200 kPa
  • Deviator stress at failure: Δ σ f = 160 kPa \Delta\sigma_f = 160 \text{ kPa} Δ σ f ​ = 160 kPa
  • Measured pore pressure at failure: u f = 100 kPa u_f = 100 \text{ kPa} u f ​ = 100 kPa

Calculate:

Total principal stresses ( σ 1 , σ 3 \sigma_1, \sigma_3 σ 1 ​ , σ 3 ​ ) and total principal stress ratio at failure.

Effective principal stresses ( σ 1 ′ , σ 3 ′ \sigma'_1, \sigma'_3 σ 1 ′ ​ , σ 3 ′ ​ ) at failure.

Effective angle of internal friction ( ϕ ′ \phi' ϕ ′ ).

Orientation of the failure plane ( θ \theta θ ) relative to the horizontal major principal plane.

Effective normal stress ( σ ′ \sigma' σ ′ ) and shear stress ( τ f \tau_f τ f ​ ) on the failure plane.

Solution:

Total Principal Stresses: σ 3 = 200 kPa \sigma_3 = 200 \text{ kPa} σ 3 ​ = 200 kPa σ 1 = σ 3 + Δ σ f = 200 + 160 = 360 kPa \sigma_1 = \sigma_3 + \Delta\sigma_f = 200 + 160 = 360 \text{ kPa} σ 1 ​ = σ 3 ​ + Δ σ f ​ = 200 + 160 = 360 kPa Total Ratio σ 1 σ 3 = 360 200 = 1.80 \text{Total Ratio } \frac{\sigma_1}{\sigma_3} = \frac{360}{200} = 1.80 Total Ratio σ 3 ​ σ 1 ​ ​ = 200 360 ​ = 1.80

Effective Principal Stresses: σ 3 ′ = σ 3 − u f = 200 − 100 = 100 kPa \sigma'_3 = \sigma_3 - u_f = 200 - 100 = 100 \text{ kPa} σ 3 ′ ​ = σ 3 ​ − u f ​ = 200 − 100 = 100 kPa σ 1 ′ = σ 1 − u f = 360 − 100 = 260 kPa \sigma'_1 = \sigma_1 - u_f = 360 - 100 = 260 \text{ kPa} σ 1 ′ ​ = σ 1 ​ − u f ​ = 360 − 100 = 260 kPa

Effective Angle of Internal Friction ( ϕ ′ \phi' ϕ ′ ): For normally consolidated clay ( c ′ = 0 c' = 0 c ′ = 0 ), the principal stress relationship is: σ 1 ′ = σ 3 ′ tan ⁡ 2 ( 45 ∘ + ϕ ′ 2 ) = σ 3 ′ ( 1 + sin ⁡ ϕ ′ 1 − sin ⁡ ϕ ′ ) \sigma'_1 = \sigma'_3 \tan^2\left(45^\circ + \frac{\phi'}{2}\right) = \sigma'_3 \left(\frac{1 + \sin\phi'}{1 - \sin\phi'}\right) σ 1 ′ ​ = σ 3 ′ ​ tan 2 ( 4 5 ∘ + 2 ϕ ′ ​ ) = σ 3 ′ ​ ( 1 − sin ϕ ′ 1 + sin ϕ ′ ​ ) σ 1 ′ σ 3 ′ = 260 100 = 2.60 \frac{\sigma'_1}{\sigma'_3} = \frac{260}{100} = 2.60 σ 3 ′ ​ σ 1 ′ ​ ​ = 100 260 ​ = 2.60 1 + sin ⁡ ϕ ′ 1 − sin ⁡ ϕ ′ = 2.60 ⟹ 1 + sin ⁡ ϕ ′ = 2.60 ( 1 − sin ⁡ ϕ ′ ) = 2.60 − 2.60 sin ⁡ ϕ ′ \frac{1 + \sin\phi'}{1 - \sin\phi'} = 2.60 \implies 1 + \sin\phi' = 2.60 (1 - \sin\phi') = 2.60 - 2.60 \sin\phi' 1 − sin ϕ ′ 1 + sin ϕ ′ ​ = 2.60 ⟹ 1 + sin ϕ ′ = 2.60 ( 1 − sin ϕ ′ ) = 2.60 − 2.60 sin ϕ ′ 3.60 sin ⁡ ϕ ′ = 1.60 ⟹ sin ⁡ ϕ ′ = 1.60 3.60 = 0.4444 3.60 \sin\phi' = 1.60 \implies \sin\phi' = \frac{1.60}{3.60} = 0.4444 3.60 sin ϕ ′ = 1.60 ⟹ sin ϕ ′ = 3.60 1.60 ​ = 0.4444 ϕ ′ = arcsin ⁡ ( 0.4444 ) = 26.38 ∘ \phi' = \arcsin(0.4444) = 26.38^\circ ϕ ′ = arcsin ( 0.4444 ) = 26.3 8 ∘

Failure Plane Orientation ( θ \theta θ ): θ = 45 ∘ + ϕ ′ 2 = 45 ∘ + 26.38 ∘ 2 = 45 ∘ + 13.19 ∘ = 58.19 ∘ \theta = 45^\circ + \frac{\phi'}{2} = 45^\circ + \frac{26.38^\circ}{2} = 45^\circ + 13.19^\circ = 58.19^\circ θ = 4 5 ∘ + 2 ϕ ′ ​ = 4 5 ∘ + 2 26.3 8 ∘ ​ = 4 5 ∘ + 13.1 9 ∘ = 58.1 9 ∘

Stresses on Failure Plane: σ ′ = σ 1 ′ + σ 3 ′ 2 + σ 1 ′ − σ 3 ′ 2 cos ⁡ ( 2 θ ) = 260 + 100 2 + 260 − 100 2 cos ⁡ ( 116.38 ∘ ) \sigma' = \frac{\sigma'_1 + \sigma'_3}{2} + \frac{\sigma'_1 - \sigma'_3}{2} \cos(2\theta) = \frac{260 + 100}{2} + \frac{260 - 100}{2} \cos(116.38^\circ) σ ′ = 2 σ 1 ′ ​ + σ 3 ′ ​ ​ + 2 σ 1 ′ ​ − σ 3 ′ ​ ​ cos ( 2 θ ) = 2 260 + 100 ​ + 2 260 − 100 ​ cos ( 116.3 8 ∘ ) σ ′ = 180 + 80 ( − 0.4444 ) = 180 − 35.56 = 144.44 kPa \sigma' = 180 + 80 (-0.4444) = 180 - 35.56 = 144.44 \text{ kPa} σ ′ = 180 + 80 ( − 0.4444 ) = 180 − 35.56 = 144.44 kPa τ f = σ ′ tan ⁡ ϕ ′ = 144.44 × tan ⁡ ( 26.38 ∘ ) = 144.44 × 0.4960 = 71.64 kPa \tau_f = \sigma' \tan\phi' = 144.44 \times \tan(26.38^\circ) = 144.44 \times 0.4960 = 71.64 \text{ kPa} τ f ​ = σ ′ tan ϕ ′ = 144.44 × tan ( 26.3 8 ∘ ) = 144.44 × 0.4960 = 71.64 kPa

Alternatively, using τ f = σ 1 ′ − σ 3 ′ 2 sin ⁡ ( 2 θ ) = 80 × sin ⁡ ( 116.38 ∘ ) = 80 × 0.8958 = 71.66 kPa ✓ \tau_f = \frac{\sigma'_1 - \sigma'_3}{2} \sin(2\theta) = 80 \times \sin(116.38^\circ) = 80 \times 0.8958 = 71.66 \text{ kPa} \quad \checkmark τ f ​ = 2 σ 1 ′ ​ − σ 3 ′ ​ ​ sin ( 2 θ ) = 80 × sin ( 116.3 8 ∘ ) = 80 × 0.8958 = 71.66 kPa ✓

Loading diagram... Mohr-Coulomb Failure Envelope and Effective Stress Circle