Study guide

4.3 Dynamic Soil Properties & Ground Response Analysis

PE Civil Geotechnical Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Site Characterization

1.1 Site Data Interpretation & Boring Plans 1.2 In Situ Testing & Field Exploration 1.3 Soil and Rock Classification Systems 1.4 Groundwater Characterization & Hydrogeology

2 Chapter 2: Soil Mechanics, Laboratory Testing, and Analysis

2.1 Weight-Volume Phase Relationships & Index Properties 2.2 Effective Stress & Pore Water Pressure Dynamics 2.3 Shear Strength Principles & Laboratory Testing 2.4 Permeability, Hydraulic Conductivity & Seepage Properties 2.5 Consolidation & Compressibility Analysis

3 Chapter 3: Construction Observation, Monitoring, QA/QC, and Safety

3.1 Earthwork Quality Control & Compaction Verification 3.2 Geotechnical Instrumentation & Field Monitoring 3.3 Trenching, Excavation Safety & OSHA Shoring Requirements 3.4 Erosion, Scour Protection & Slope Protection During Construction

4 Chapter 4: Earthquake Engineering and Dynamic Loads

4.1 Seismic Site Characterization & Ground Motion Hazards 4.2 Soil Liquefaction Triggering & Post-Liquefaction Assessment 4.3 Dynamic Soil Properties & Ground Response Analysis 4.4 Pseudostatic Analysis & Seismic Geotechnical Design

5 Chapter 5: Earth Structures, Ground Improvement, and Pavement

5.1 Slope Stability Analysis & Limit Equilibrium Methods 5.2 Embankments, Earth Dams & Levee Geotechnics 5.3 Ground Improvement Techniques & Design 5.4 Geosynthetics in Geotechnical Engineering 5.5 Flexible & Rigid Pavement Subgrades & Buried Utilities 5.6 Landfills, Caps & Containment Systems

6 Chapter 6: Groundwater and Seepage

6.1 Dewatering System Design & Well Drawdown 6.2 Flow Nets & Two-Dimensional Seepage Analysis 6.3 Uplift Pressure, Piping & Heave Safety 6.4 Subsurface Drainage Systems & Filter Criteria

7 Chapter 7: Problematic Soil and Rock Conditions

7.1 Expansive & Collapsible Soil Engineering 7.2 Organic Soils, Sensitive Clays & Soft Marine Deposits 7.3 Corrosive, Frost-Susceptible & Degradable Formations 7.4 Karst Topography, Rock Slopes & Rockfall Hazards

8 Chapter 8: Retaining Structures

8.1 Lateral Earth Pressure Theories 8.2 Rigid Retaining Wall Design 8.3 Flexible Retaining Walls & Sheet Pile Bulkheads 8.4 Temporary Support of Excavations 8.5 Mechanically Stabilized Earth (MSE) Walls & Soil Nail Structures 8.6 Cofferdams, Underpinning & Adjacent Infrastructure Effects

9 Chapter 9: Shallow Foundations

9.1 Ultimate & Allowable Bearing Capacity Theories 9.2 Effective Footing Area, Eccentricity & Combined Footings 9.3 Induced Stress Distribution & Immediate Elastic Settlement 9.4 Consolidation Settlement & Mat/Raft Foundation Design

10 Chapter 10: Deep Foundations

10.1 Driven Pile Axial Capacity & Settlement 10.2 Drilled Shaft Axial Design & Construction Methods 10.3 Lateral Load Behavior of Deep Foundations 10.4 Pile Group Dynamics, Efficiency & Downdrag 10.5 Dynamic Load Testing & Pile Integrity Evaluation

4.3 Dynamic Soil Properties & Ground Response Analysis

Key Takeaways Explain This Topic AI

The small-strain shear modulus Gmax represents the maximum stiffness of soil at shear strains gamma <= 10^-6 and is directly related to shear wave velocity by Gmax = rho * Vs^2.

Soil exhibits nonlinear hysteretic stress-strain behavior under dynamic loading, characterized by shear modulus reduction (G/Gmax) curves and hysteretic damping ratio (D) curves that vary with cyclic shear strain amplitude.

Equivalent Linear (EQL) ground response analysis iteratively computes wave propagation by updating G and D based on effective cyclic strain (gamma_eff ≈ 0.65 * gamma_max).

The fundamental period of a single uniform soil layer above rigid bedrock is Ts = 4H / Vs.

Site amplification or de-amplification is governed by the impedance contrast between bedrock and soil, layer stratigraphy, and non-linear strain degradation.

Last updated: July 2026

  • 4.3 Dynamic Soil Properties & Ground Response Analysis
  • 1. Small-Strain Dynamic Soil Properties

Under dynamic loading (earthquakes, machine vibrations, wave action), soil behavior is non-linear, inelastic, and strain-dependent. At very small shear strains ( γ ≤ 10 − 6 \gamma \le 10^{-6} γ ≤ 1 0 − 6 or 10 − 4 % 10^{-4}\% 1 0 − 4 % ), soil behaves in a linear-elastic manner without acoustic energy loss or permanent fabric rearrangement. The maximum shear modulus, designated as G m a x G_{max} G ma x ​ (or G 0 G_0 G 0 ​ ), is a fundamental parameter in dynamic geotechnical engineering: G m a x = ρ V s 2 = ( γ t g ) V s 2 G_{max} = \rho V_s^2 = \left(\frac{\gamma_t}{g}\right) V_s^2 G ma x ​ = ρ V s 2 ​ = ( g γ t ​ ​ ) V s 2 ​

where:

ρ \rho ρ = mass density of soil ( kg/m 3 \text{kg/m}^3 kg/m 3 or slugs/ft 3 \text{slugs/ft}^3 slugs/ft 3 ).

γ t \gamma_t γ t ​ = total unit weight of soil ( kN/m 3 \text{kN/m}^3 kN/m 3 or pcf \text{pcf} pcf ).

g g g = acceleration of gravity ( 9.81 m/s 2 9.81\text{ m/s}^2 9.81 m/s 2 or 32.2 ft/s 2 32.2\text{ ft/s}^2 32.2 ft/s 2 ).

V s V_s V s ​ = low-strain shear wave velocity ( m/s \text{m/s} m/s or ft/s \text{ft/s} ft/s ).

Empirical correlations express G m a x G_{max} G ma x ​ for clean sands as a function of mean effective stress ( σ m ′ \sigma'_m σ m ′ ​ ) and void ratio ( e e e ) (Hardin & Drnevich 1972): G m a x = 625 0.3 + 0.7 e 2 ⋅ P a 1 − n ⋅ ( σ m ′ ) n G_{max} = \frac{625}{0.3 + 0.7 e^2} \cdot P_a^{1-n} \cdot (\sigma'_m)^n G ma x ​ = 0.3 + 0.7 e 2 625 ​ ⋅ P a 1 − n ​ ⋅ ( σ m ′ ​ ) n

where n ≈ 0.5 n \approx 0.5 n ≈ 0.5 for granular soils and P a P_a P a ​ is atmospheric pressure.

2. Modulus Reduction ( G / G m a x G/G_{max} G / G ma x ​ ) and Damping Ratio ( D D D ) Curves

As cyclic shear strain amplitude ( γ \gamma γ ) increases beyond the elastic threshold, two key developments occur:

Modulus Reduction: Soil stiffness degrades due to micro-slippage at particle contacts. The secant shear modulus G G G decreases below G m a x G_{max} G ma x ​ , defining the normalized modulus reduction curve G / G m a x G/G_{max} G / G ma x ​ vs. γ \gamma γ .

Hysteretic Damping: Energy is dissipated per loading cycle through mechanical friction and plastic deformation. The equivalent hysteretic damping ratio D D D increases from a minimum small-strain damping D m i n D_{min} D min ​ (typically 1 % − 3 % 1\% - 3\% 1% − 3% ) to large-strain values exceeding 20 % − 25 % 20\% - 25\% 20% − 25% . Strain Threshold Boundaries:

  • 1. γ <= 10^-6 (10^-4 %): Linear Elastic Region (G = Gmax, D = Dmin, no permanent strain)
  • 2. 10^-6 < γ <= 10^-4: Elastic-Plastic Non-Linear Region (G begins to decrease, D increases)
  • 3. γ > 10^-4 (10^-2 %): Volumetric Strain Threshold γ_tv (Pore water pressure accumulation begins)

Influencing factors (Vucetic & Dobry 1991; Darendeli 2001):

Plasticity Index ( P I PI P I ): High plasticity clays retain linear behavior up to higher shear strains compared to non-plastic sands. Consequently, high P I PI P I soils exhibit less modulus degradation (higher G / G m a x G/G_{max} G / G ma x ​ ) and lower damping ratios ( D D D ) at a given shear strain level.

Effective Overburden Stress ( σ m ′ \sigma'_m σ m ′ ​ ): Higher effective confining stress increases G / G m a x G/G_{max} G / G ma x ​ curves and decreases damping D D D in cohesionless soils.

3. One-Dimensional Ground Response Wave Equation

Ground response analysis computes how vertically propagating body shear waves (S-waves) travel from underlying bedrock through soil layers to the ground surface. For a viscoelastic horizontal soil layer of mass density ρ \rho ρ , the 1D shear wave propagation equation is expressed as: ρ ∂ 2 u ∂ t 2 = G ∂ 2 u ∂ z 2 + η ∂ 3 u ∂ z 2 ∂ t \rho \frac{\partial^2 u}{\partial t^2} = G \frac{\partial^2 u}{\partial z^2} + \eta \frac{\partial^3 u}{\partial z^2 \partial t} ρ ∂ t 2 ∂ 2 u ​ = G ∂ z 2 ∂ 2 u ​ + η ∂ z 2 ∂ t ∂ 3 u ​

where u ( z , t ) u(z,t) u ( z , t ) is horizontal displacement, G G G is shear modulus, and η \eta η is viscous damping coefficient (where viscosity η = 2 G D ω \eta = \frac{2 G D}{\omega} η = ω 2 G D ​ ).

In frequency-domain complex notation, the dynamic shear modulus G ∗ G^* G ∗ is written as: G ∗ = G ( 1 + 2 i D ) G^* = G (1 + 2i D) G ∗ = G ( 1 + 2 i D )

4. Equivalent Linear (EQL) vs. Fully Nonlinear (NL) Analysis

Two principal numerical frameworks are used in geotechnical engineering practice to solve 1D ground response:

1. Equivalent Linear Method (EQL - SHAKE Approach)

Concept: Approximates non-linear hysteretic soil response using linear viscoelastic wave propagation theory, solved iteratively in the frequency domain.

Procedure:

Assume initial estimates of G = G m a x G = G_{max} G = G ma x ​ and D = D m i n D = D_{min} D = D min ​ for each soil layer.

Perform frequency-domain wave propagation to compute horizontal acceleration and shear strain time histories.

Determine the maximum shear strain γ m a x \gamma_{max} γ ma x ​ in each layer and compute an effective cyclic shear strain : γ e f f = R γ ⋅ γ m a x \gamma_{eff} = R\gamma \cdot \gamma_{max} γ e ff ​ = R γ ⋅ γ ma x ​ where R γ ≈ 0.65 R_\gamma \approx 0.65 R γ ​ ≈ 0.65 (or R γ = M w − 1 10 R_\gamma = \frac{M_w - 1}{10} R γ ​ = 10 M w ​ − 1 ​ ).

Read updated values of G n e w G_{new} G n e w ​ and D n e w D_{new} D n e w ​ from the strain-dependent soil property curves ( G / G m a x G/G_{max} G / G ma x ​ and D D D vs. γ e f f \gamma_{eff} γ e ff ​ ).

Check convergence: If ∣ G n e w − G o l d ∣ / G o l d > tolerance |G_{new} - G_{old}| / G_{old} > \text{tolerance} ∣ G n e w ​ − G o l d ​ ∣/ G o l d ​ > tolerance (typically 1 % 1\% 1% ), repeat steps 2–4.

Limitations: Cannot model permanent shear deformations or transient pore pressure buildup ( r u r_u r u ​ ), and tends to over-damp high frequencies during strong shaking ( γ m a x > 1 % \gamma_{max} > 1\% γ ma x ​ > 1% ).

2. Fully Nonlinear Method (NL - DEEPSOIL / PM4Sand / PDMY)

Direct time-domain integration of constitutive stress-strain relationships.

Models hysteresis loops directly, including cyclic pore pressure generation, strain-hardening, dilatancy, and residual shear deformation.

5. Site Period, Resonance, and Impedance Ratio

The fundamental period of a soil deposit ( T s T_s T s ​ ) governs how the ground filters bedrock motions. For a uniform single soil layer of thickness H H H over rigid bedrock: T s = 4 H V s T_s = \frac{4H}{V_s} T s ​ = V s ​ 4 H ​ f s = 1 T s = V s 4 H f_s = \frac{1}{T_s} = \frac{V_s}{4H} f s ​ = T s ​ 1 ​ = 4 H V s ​ ​

For a multi-layered soil profile, the effective fundamental period is computed using travel-time summation: T s = 4 ∑ i = 1 n d i V s i T_s = 4 \sum_{i=1}^{n} \frac{d_i}{V_{si}} T s ​ = 4 i = 1 ∑ n ​ V s i ​ d i ​ ​

Impedance Ratio ( α \alpha α ):

The contrast in dynamic stiffness between the underlying rock (base) and overlying soil layer 1 determines energy transmission and reflection across the boundary: α = ρ 1 V s 1 ρ r o c k V s , r o c k \alpha = \frac{\rho_1 V_{s1}}{\rho_{rock} V_{s,rock}} α = ρ roc k ​ V s , roc k ​ ρ 1 ​ V s 1 ​ ​

At the fundamental frequency ( f s f_s f s ​ ), the theoretical amplification ratio A m a x A_{max} A ma x ​ of ground motion from rigid bedrock to surface (with soil damping D D D ) is: A m a x ≈ 1 α + π 2 D A_{max} \approx \frac{1}{\alpha + \frac{\pi}{2} D} A ma x ​ ≈ α + 2 π ​ D 1 ​

When the natural period of an overlying building structure ( T s t r u c t T_{struct} T s t r u c t ​ ) matches the fundamental site period ( T s T_s T s ​ ), double resonance occurs, inducing high structural accelerations and catastrophic damage.

6. Comprehensive Step-by-Step Worked Example

Problem Statement:

A foundation site consists of a 20.0 -meter 20.0\text{-meter} 20.0 -meter thick uniform stiff clay deposit over bedrock.

  • Clay unit weight: γ t = 19.0 kN/m 3 \gamma_t = 19.0\text{ kN/m}^3 γ t ​ = 19.0 kN/m 3
  • Measured shear wave velocity: V s = 250 m/s V_s = 250\text{ m/s} V s ​ = 250 m/s

Bedrock properties: γ r o c k = 24.0 kN/m 3 \gamma_{rock} = 24.0\text{ kN/m}^3 γ roc k ​ = 24.0 kN/m 3 , V s , r o c k = 1200 m/s V_{s,rock} = 1200\text{ m/s} V s , roc k ​ = 1200 m/s

Soil damping ratio at small strains: D = 4.0 % = 0.04 D = 4.0\% = 0.04 D = 4.0% = 0.04

Structure proposed for the site: A 5-story reinforced concrete building with an estimated natural period T s t r u c t = 0.50 s T_{struct} = 0.50\text{ s} T s t r u c t ​ = 0.50 s .

Calculate:

Small-strain shear modulus G m a x G_{max} G ma x ​ of the clay layer.

Fundamental period ( T s T_s T s ​ ) and fundamental frequency ( f s f_s f s ​ ) of the soil profile.

Impedance ratio ( α \alpha α ) between the clay layer and underlying bedrock.

Theoretical peak amplifications ratio ( A m a x A_{max} A ma x ​ ) at the site's fundamental period.

Assess whether double resonance between the structure and ground site is a design concern.

Solution:

Step 1: Compute Small-Strain Shear Modulus ( G m a x G_{max} G ma x ​ )

Mass density of clay: ρ = γ t g = 19 , 000 N/m 3 9.81 m/s 2 = 1 , 936.8 kg/m 3 \rho = \frac{\gamma_t}{g} = \frac{19,000\text{ N/m}^3}{9.81\text{ m/s}^2} = 1,936.8\text{ kg/m}^3 ρ = g γ t ​ ​ = 9.81 m/s 2 19 , 000 N/m 3 ​ = 1 , 936.8 kg/m 3 G m a x = ρ V s 2 = 1 , 936.8 kg/m 3 × ( 250 m/s ) 2 = 121 , 050 , 000 Pa = 121.05 MPa G_{max} = \rho V_s^2 = 1,936.8\text{ kg/m}^3 \times (250\text{ m/s})^2 = 121,050,000\text{ Pa} = \mathbf{121.05\text{ MPa}} G ma x ​ = ρ V s 2 ​ = 1 , 936.8 kg/m 3 × ( 250 m/s ) 2 = 121 , 050 , 000 Pa = 121.05 MPa

Step 2: Fundamental Site Period ( T s T_s T s ​ ) and Frequency ( f s f_s f s ​ ) T s = 4 H V s = 4 × 20.0 m 250 m/s = 0.320 s T_s = \frac{4H}{V_s} = \frac{4 \times 20.0\text{ m}}{250\text{ m/s}} = \mathbf{0.320\text{ s}} T s ​ = V s ​ 4 H ​ = 250 m/s 4 × 20.0 m ​ = 0.320 s f s = 1 T s = 1 0.320 s = 3.125 Hz f_s = \frac{1}{T_s} = \frac{1}{0.320\text{ s}} = \mathbf{3.125\text{ Hz}} f s ​ = T s ​ 1 ​ = 0.320 s 1 ​ = 3.125 Hz

Step 3: Compute Impedance Ratio ( α \alpha α ) ρ r o c k = 24 , 000 9.81 = 2 , 446.5 kg/m 3 \rho_{rock} = \frac{24,000}{9.81} = 2,446.5\text{ kg/m}^3 ρ roc k ​ = 9.81 24 , 000 ​ = 2 , 446.5 kg/m 3 α = ρ c l a y V s , c l a y ρ r o c k V s , r o c k = 1 , 936.8 × 250 2 , 446.5 × 1200 = 484 , 200 2 , 935 , 800 = 0.1649 \alpha = \frac{\rho_{clay} V_{s,clay}}{\rho_{rock} V_{s,rock}} = \frac{1,936.8 \times 250}{2,446.5 \times 1200} = \frac{484,200}{2,935,800} = \mathbf{0.1649} α = ρ roc k ​ V s , roc k ​ ρ c l a y ​ V s , c l a y ​ ​ = 2 , 446.5 × 1200 1 , 936.8 × 250 ​ = 2 , 935 , 800 484 , 200 ​ = 0.1649

Step 4: Peak Theoretical Site Amplification Ratio ( A m a x A_{max} A ma x ​ ) A m a x ≈ 1 α + π 2 D = 1 0.1649 + ( π 2 × 0.04 ) = 1 0.1649 + 0.0628 = 1 0.2277 = 4.39 A_{max} \approx \frac{1}{\alpha + \frac{\pi}{2} D} = \frac{1}{0.1649 + \left(\frac{\pi}{2} \times 0.04\right)} = \frac{1}{0.1649 + 0.0628} = \frac{1}{0.2277} = \mathbf{4.39} A ma x ​ ≈ α + 2 π ​ D 1 ​ = 0.1649 + ( 2 π ​ × 0.04 ) 1 ​ = 0.1649 + 0.0628 1 ​ = 0.2277 1 ​ = 4.39

  • Step 5: Assessment of Building Resonance
  • Soil site period T s = 0.32 s T_s = 0.32\text{ s} T s ​ = 0.32 s
  • Building natural period T s t r u c t = 0.50 s T_{struct} = 0.50\text{ s} T s t r u c t ​ = 0.50 s

Ratio T s t r u c t / T s = 0.50 / 0.32 = 1.56 T_{struct} / T_s = 0.50 / 0.32 = 1.56 T s t r u c t ​ / T s ​ = 0.50/0.32 = 1.56 .

Since T s t r u c t T_{struct} T s t r u c t ​ does not equal T s T_s T s ​ (they differ by over 50 % 50\% 50% ), direct resonance is mitigated. However, non-linear softening during strong shaking will lengthen the soil period T s T_s T s ​ toward 0.45 − 0.50 s 0.45 - 0.50\text{ s} 0.45 − 0.50 s , which could bring the degraded site period into resonance with the building during a major seismic event.

Loading diagram... Dynamic Soil Property Variation with Cyclic Strain