Study guide
5.1 Slope Stability Analysis & Limit Equilibrium Methods
PE Civil Geotechnical Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Site Characterization
1.1 Site Data Interpretation & Boring Plans 1.2 In Situ Testing & Field Exploration 1.3 Soil and Rock Classification Systems 1.4 Groundwater Characterization & Hydrogeology
2 Chapter 2: Soil Mechanics, Laboratory Testing, and Analysis
2.1 Weight-Volume Phase Relationships & Index Properties 2.2 Effective Stress & Pore Water Pressure Dynamics 2.3 Shear Strength Principles & Laboratory Testing 2.4 Permeability, Hydraulic Conductivity & Seepage Properties 2.5 Consolidation & Compressibility Analysis
3 Chapter 3: Construction Observation, Monitoring, QA/QC, and Safety
3.1 Earthwork Quality Control & Compaction Verification 3.2 Geotechnical Instrumentation & Field Monitoring 3.3 Trenching, Excavation Safety & OSHA Shoring Requirements 3.4 Erosion, Scour Protection & Slope Protection During Construction
4 Chapter 4: Earthquake Engineering and Dynamic Loads
4.1 Seismic Site Characterization & Ground Motion Hazards 4.2 Soil Liquefaction Triggering & Post-Liquefaction Assessment 4.3 Dynamic Soil Properties & Ground Response Analysis 4.4 Pseudostatic Analysis & Seismic Geotechnical Design
5 Chapter 5: Earth Structures, Ground Improvement, and Pavement
5.1 Slope Stability Analysis & Limit Equilibrium Methods 5.2 Embankments, Earth Dams & Levee Geotechnics 5.3 Ground Improvement Techniques & Design 5.4 Geosynthetics in Geotechnical Engineering 5.5 Flexible & Rigid Pavement Subgrades & Buried Utilities 5.6 Landfills, Caps & Containment Systems
6 Chapter 6: Groundwater and Seepage
6.1 Dewatering System Design & Well Drawdown 6.2 Flow Nets & Two-Dimensional Seepage Analysis 6.3 Uplift Pressure, Piping & Heave Safety 6.4 Subsurface Drainage Systems & Filter Criteria
7 Chapter 7: Problematic Soil and Rock Conditions
7.1 Expansive & Collapsible Soil Engineering 7.2 Organic Soils, Sensitive Clays & Soft Marine Deposits 7.3 Corrosive, Frost-Susceptible & Degradable Formations 7.4 Karst Topography, Rock Slopes & Rockfall Hazards
8 Chapter 8: Retaining Structures
8.1 Lateral Earth Pressure Theories 8.2 Rigid Retaining Wall Design 8.3 Flexible Retaining Walls & Sheet Pile Bulkheads 8.4 Temporary Support of Excavations 8.5 Mechanically Stabilized Earth (MSE) Walls & Soil Nail Structures 8.6 Cofferdams, Underpinning & Adjacent Infrastructure Effects
9 Chapter 9: Shallow Foundations
9.1 Ultimate & Allowable Bearing Capacity Theories 9.2 Effective Footing Area, Eccentricity & Combined Footings 9.3 Induced Stress Distribution & Immediate Elastic Settlement 9.4 Consolidation Settlement & Mat/Raft Foundation Design
10 Chapter 10: Deep Foundations
10.1 Driven Pile Axial Capacity & Settlement 10.2 Drilled Shaft Axial Design & Construction Methods 10.3 Lateral Load Behavior of Deep Foundations 10.4 Pile Group Dynamics, Efficiency & Downdrag 10.5 Dynamic Load Testing & Pile Integrity Evaluation
5.1 Slope Stability Analysis & Limit Equilibrium Methods
Key Takeaways Explain This Topic AI
Limit equilibrium methods evaluate the factor of safety (FS) along a potential slip surface by comparing available shear strength to mobilized shear stress.
The Ordinary Method of Slices (Fellenius) neglects interslice forces, providing a conservative FS estimate that typically underpredicts stability by 5% to 15%.
Bishop's Simplified Method satisfies vertical force and overall moment equilibrium while assuming horizontal interslice forces, yielding accurate results for circular slip surfaces.
Spencer's and Morgenstern-Price methods satisfy both force and moment equilibrium for arbitrary slip surface geometries by solving for interslice force inclinations.
For infinite slopes in cohesionless soils with parallel seepage, the factor of safety reduces to FS = (gamma' / gamma_sat) * (tan phi' / tan beta), roughly half that of a dry slope.
Last updated: July 2026
Introduction to Slope Stability Analysis
Slope stability analysis is a fundamental discipline in geotechnical engineering, essential for evaluating the stability of natural slopes, engineered embankments, earth dams, deep excavations, and soil cuts. The primary objective is to determine the Factor of Safety ( F S FS FS ) against shear failure along a potential slip surface.
The general definition of the Factor of Safety against slope failure is expressed as the ratio of the available shear strength ( τ f \tau_f τ f ) along the failure surface to the mobilized shear stress ( τ m \tau_m τ m ) required to maintain equilibrium: F S = τ f τ m = c ′ + σ n ′ tan ϕ ′ τ m FS = \frac{\tau_f}{\tau_m} = \frac{c' + \sigma'_n \tan\phi'}{\tau_m} FS = τ m τ f = τ m c ′ + σ n ′ tan ϕ ′
where:
c ′ c' c ′ is the effective cohesion intercept of the soil
σ n ′ = ( σ n − u ) \sigma'_n = (\sigma_n - u) σ n ′ = ( σ n − u ) is the effective normal stress on the failure plane
- u u u is the pore water pressure
- ϕ ′ \phi' ϕ ′ is the effective internal friction angle
- Slope Failure Mechanisms & Surface Geometries
Depending on soil stratigraphy, strength anisotropy, and geological boundary conditions, slope failures exhibit distinct kinematic modes:
Circular Rotational Failures : Prevalent in homogeneous clay cuts, soft ground embankments, and uniform fills. The slip surface forms a continuous curved arc that can be approximated by a circular segment.
Planar (Translational) Failures : Common in stratified deposits where a weak soil layer or bedding plane runs parallel to the slope face. The failure mass slides along a flat plane.
Non-Circular Arbitrary Slip Surfaces : Occur in non-homogeneous, multi-layered soils with variable pore pressure regimes or structural weak seams.
Infinite Slopes : Shallow failure surfaces where the depth of the slip surface ( z z z ) is significantly smaller than the length of the slope ( L ≫ z L \gg z L ≫ z ).
Total Stress Analysis (TSA) vs. Effective Stress Analysis (ESA)
Geotechnical engineers must select the appropriate stress analysis framework based on drainage conditions and time frames:
Total Stress Analysis (TSA / Short-Term / Undrained) : Used for short-term evaluation immediately after construction or excavation in saturated cohesive soils. The shear strength is governed by the undrained shear strength ( s u s_u s u or c u c_u c u , with ϕ u = 0 \phi_u = 0 ϕ u = 0 ). Excess pore water pressure generated by construction load changes does not have time to dissipate.
Effective Stress Analysis (ESA / Long-Term / Drained) : Used for long-term stability analysis under steady-state seepage conditions, or rapid drawdown conditions in free-draining materials. Soil strength is defined by effective strength parameters ( c ′ , ϕ ′ c', \phi' c ′ , ϕ ′ ) and the equilibrium pore water pressure grid ( u u u ) derived from seepage flow nets.
Infinite Slope Mechanics & Mathematical Formulations
An infinite slope represents an idealized condition where soil properties, groundwater depth, and slope inclination are uniform over an infinite extent. This model is highly accurate for shallow translational slides parallel to the slope face.
Case 1: Dry or Fully Drained Cohesionless Soil ( c ′ = 0 , u = 0 c' = 0, u = 0 c ′ = 0 , u = 0 )
Consider an element of soil at depth z z z on a slope inclined at angle β \beta β to the horizontal. The weight of the soil block of unit width is W = γ z cos β W = \gamma z \cos\beta W = γ z cos β . Resolving W W W into normal and shear components along the base plane yields: σ n = γ z cos 2 β \sigma_n = \gamma z \cos^2\beta σ n = γ z cos 2 β τ m = γ z sin β cos β \tau_m = \gamma z \sin\beta \cos\beta τ m = γ z sin β cos β
The available frictional strength is τ f = σ n tan ϕ ′ = γ z cos 2 β tan ϕ ′ \tau_f = \sigma_n \tan\phi' = \gamma z \cos^2\beta \tan\phi' τ f = σ n tan ϕ ′ = γ z cos 2 β tan ϕ ′ . The Factor of Safety is: F S = τ f τ m = γ z cos 2 β tan ϕ ′ γ z sin β cos β = tan ϕ ′ tan β FS = \frac{\tau_f}{\tau_m} = \frac{\gamma z \cos^2\beta \tan\phi'}{\gamma z \sin\beta \cos\beta} = \frac{\tan\phi'}{\tan\beta} FS = τ m τ f = γ z sin β cos β γ z cos 2 β tan ϕ ′ = tan β tan ϕ ′
Key Concept : A dry, cohesionless slope is stable ( F S ≥ 1.0 FS \ge 1.0 FS ≥ 1.0 ) as long as the slope angle β \beta β does not exceed the soil's effective friction angle ϕ ′ \phi' ϕ ′ . Depth z z z and unit weight γ \gamma γ do not affect stability.
Case 2: Cohesive-Frictional Soil without Seepage ( c ′ > 0 , ϕ ′ > 0 , u = 0 c' > 0, \phi' > 0, u = 0 c ′ > 0 , ϕ ′ > 0 , u = 0 )
Including effective cohesion c ′ c' c ′ introduces a depth-dependent term: F S = c ′ + γ z cos 2 β tan ϕ ′ γ z sin β cos β = c ′ γ z sin β cos β + tan ϕ ′ tan β FS = \frac{c' + \gamma z \cos^2\beta \tan\phi'}{\gamma z \sin\beta \cos\beta} = \frac{c'}{\gamma z \sin\beta \cos\beta} + \frac{\tan\phi'}{\tan\beta} FS = γ z sin β cos β c ′ + γ z cos 2 β tan ϕ ′ = γ z sin β cos β c ′ + tan β tan ϕ ′
Here, cohesion increases the factor of safety, particularly at shallow depths ( z z z ). The critical depth z c r z_{cr} z cr at which failure occurs ( F S = 1.0 FS = 1.0 FS = 1.0 ) can be calculated directly by rearranging the equation.
Case 3: Cohesionless Soil with Parallel Seepage to Ground Surface ( c ′ = 0 c' = 0 c ′ = 0 )
When seepage flows parallel to the slope face with the phreatic surface at the ground surface, the pore water pressure at depth z z z is u = γ w z cos 2 β u = \gamma_w z \cos^2\beta u = γ w z cos 2 β . The effective normal stress becomes: σ n ′ = σ n − u = γ s a t z cos 2 β − γ w z cos 2 β = ( γ s a t − γ w ) z cos 2 β = γ ′ z cos 2 β \sigma'_n = \sigma_n - u = \gamma_{sat} z \cos^2\beta - \gamma_w z \cos^2\beta = (\gamma_{sat} - \gamma_w) z \cos^2\beta = \gamma' z \cos^2\beta σ n ′ = σ n − u = γ s a t z cos 2 β − γ w z cos 2 β = ( γ s a t − γ w ) z cos 2 β = γ ′ z cos 2 β
where γ ′ \gamma' γ ′ is the submerged (buoyant) unit weight of the soil ( γ ′ = γ s a t − γ w \gamma' = \gamma_{sat} - \gamma_w γ ′ = γ s a t − γ w ). Substituting σ n ′ \sigma'_n σ n ′ into the factor of safety equation yields: F S = γ ′ z cos 2 β tan ϕ ′ γ s a t z sin β cos β = ( γ ′ γ s a t ) tan ϕ ′ tan β FS = \frac{\gamma' z \cos^2\beta \tan\phi'}{\gamma_{sat} z \sin\beta \cos\beta} = \left( \frac{\gamma'}{\gamma_{sat}} \right) \frac{\tan\phi'}{\tan\beta} FS = γ s a t z sin β cos β γ ′ z cos 2 β tan ϕ ′ = ( γ s a t γ ′ ) tan β tan ϕ ′
Since γ ′ ≈ 0.5 γ s a t \gamma' \approx 0.5 \gamma_{sat} γ ′ ≈ 0.5 γ s a t for typical soils (e.g., γ s a t ≈ 19 − 20 kN/m 3 , γ ′ ≈ 9 − 10 kN/m 3 \gamma_{sat} \approx 19-20\text{ kN/m}^3, \gamma' \approx 9-10\text{ kN/m}^3 γ s a t ≈ 19 − 20 kN/m 3 , γ ′ ≈ 9 − 10 kN/m 3 ), seepage parallel to the slope cuts the Factor of Safety in half compared to the dry condition!
Limit Equilibrium Method of Slices
For non-infinite slopes with curved or arbitrary failure surfaces, the sliding mass is discretized into n n n vertical slices to account for varying soil properties, pore water pressures, and slope geometry along the slip surface.
Force Equilibrium on an Individual Slice
Each vertical slice i i i of width b i b_i b i experiences the following system of forces:
- Slice weight W i = γ i b i h i W_i = \gamma_i b_i h_i W i = γ i b i h i
- Base normal force N i N_i N i and base shear force T i T_i T i
Pore water pressure force at the base U i = u i l i U_i = u_i l_i U i = u i l i , where l i = b i / cos α i l_i = b_i / \cos\alpha_i l i = b i / cos α i
Interslice normal forces E L , i E_{L,i} E L , i and E R , i E_{R,i} E R , i acting on the left and right vertical boundaries
Interslice shear forces X L , i X_{L,i} X L , i and X R , i X_{R,i} X R , i acting along the vertical boundaries
- Pseudostatic seismic force k h W i k_h W_i k h W i (if seismic loading is analyzed)
- Method Comparison and Equilibrium Assumptions
Different limit equilibrium methods make specific simplifying assumptions regarding interslice forces to resolve the statically indeterminate system:
Loading diagram... Limit Equilibrium Slice Force Architecture
1. Ordinary Method of Slices (Fellenius / Swedish Circle)
The Ordinary Method of Slices assumes that interslice forces E E E and X X X are parallel to the base of each slice and cancel each other out ( E L = E R , X L = X R E_L = E_R, X_L = X_R E L = E R , X L = X R ). This simplifies base normal force resolution: N i ′ = N i − U i = W i cos α i − u i l i N'_i = N_i - U_i = W_i \cos\alpha_i - u_i l_i N i ′ = N i − U i = W i cos α i − u i l i
The global factor of safety is derived solely from overall moment equilibrium about the center of the circular slip surface: F S = ∑ [ c ′ l i + ( W i cos α i − u i l i ) tan ϕ ′ ] ∑ W i sin α i FS = \frac{\sum \left[ c' l_i + (W_i \cos\alpha_i - u_i l_i) \tan\phi' \right]}{\sum W_i \sin\alpha_i} FS = ∑ W i sin α i ∑ [ c ′ l i + ( W i cos α i − u i l i ) tan ϕ ′ ]
Pros : Simple to calculate manually without iterative software routines.
Cons : Neglects interslice forces; can be significantly conservative, underestimating F S FS FS by 5% to 15% (or overestimating error in deep circles with high pore pressures).
2. Bishop's Simplified Method
Bishop's Simplified Method assumes interslice shear forces are zero ( X L = X R = 0 X_L = X_R = 0 X L = X R = 0 ), but includes horizontal interslice forces ( E L , E R E_L, E_R E L , E R ). It satisfies vertical force equilibrium for each slice and overall moment equilibrium about the center of rotation.
The resulting equation for F S FS FS is: F S = ∑ c ′ b i + ( W i − u i b i ) tan ϕ ′ m α ∑ W i sin α i FS = \frac{\sum \frac{c' b_i + (W_i - u_i b_i) \tan\phi'}{m\alpha}}{\sum W_i \sin\alpha_i} FS = ∑ W i sin α i ∑ m α c ′ b i + ( W i − u i b i ) t a n ϕ ′
where the term m α m_\alpha m α is defined as: m α = cos α i ( 1 + tan α i tan ϕ ′ F S ) m\alpha = \cos\alpha_i \left( 1 + \frac{\tan\alpha_i \tan\phi'}{FS} \right) m α = cos α i ( 1 + FS tan α i tan ϕ ′ )
Pros : Highly accurate for circular failure surfaces (typically within 1-2% of rigorous methods).
Cons : Requires iterative solution because F S FS FS appears on both sides of the equation (inside m α m_\alpha m α ).
3. Janbu's Simplified Method
Janbu's Simplified Method is designed for non-circular (composite or planar) slip surfaces. It assumes horizontal interslice forces ( X i = 0 X_i = 0 X i = 0 ) and satisfies force equilibrium (horizontal and vertical) across all slices. It applies an empirical correction factor f 0 f_0 f 0 to account for interslice shear forces: F S c o r r e c t e d = f 0 ⋅ F S u n c o r r e c t e d FS_{corrected} = f_0 \cdot FS_{uncorrected} F S correc t e d = f 0 ⋅ F S u n correc t e d
4. Spencer's Method & Morgenstern-Price Method
Spencer's Method : Assumes interslice forces are inclined at a constant angle θ \theta θ across all slices ( X / E = tan θ X/E = \tan\theta X / E = tan θ ). Solves for both θ \theta θ and F S FS FS , fully satisfying both force equilibrium and moment equilibrium for arbitrary slip surfaces.
Morgenstern-Price Method : Assumes interslice force inclination varies according to a prescribed function f ( x ) f(x) f ( x ) scaled by λ \lambda λ ( X / E = λ f ( x ) X/E = \lambda f(x) X / E = λ f ( x ) ). Satisfies both force and moment equilibrium and is considered the standard for modern 2D and 3D limit equilibrium software.
Comparison of Limit Equilibrium Slope Stability Methods
Method Slip Surface Geometry Satisfies Force Equilibrium? Satisfies Moment Equilibrium? Interslice Force Assumption
- Ordinary (Fellenius) Circular No Yes Interslice forces neglected ( E = 0 , X = 0 E=0, X=0 E = 0 , X = 0 )
- Bishop's Simplified Circular Vertical only Yes Horizontal interslice forces ( X = 0 X=0 X = 0 )
Janbu's Simplified Non-circular / Arbitrary Yes (overall) No Horizontal interslice forces ( X = 0 X=0 X = 0 ) + f 0 f_0 f 0 correction
Spencer's Method Arbitrary Yes Yes Interslice force inclination θ \theta θ is constant
Morgenstern-Price Arbitrary Yes Yes Interslice force inclination tan θ = λ f ( x ) \tan\theta = \lambda f(x) tan θ = λ f ( x )
Taylor's Stability Charts & Mass Procedures
For homogeneous, purely cohesive slopes ( ϕ u = 0 \phi_u = 0 ϕ u = 0 ) under total stress conditions, Taylor developed chart solutions based on the dimensionless Stability Number ( N s N_s N s ) : N s = c u γ H ⋅ F S ⟹ F S = c u γ H N s N_s = \frac{c_u}{\gamma H \cdot FS} \quad \implies \quad FS = \frac{c_u}{\gamma H N_s} N s = γ H ⋅ FS c u ⟹ FS = γ H N s c u
where:
- c u c_u c u is the undrained shear strength
- γ \gamma γ is the total unit weight of the soil
- H H H is the height of the slope cut
N s N_s N s is Taylor's stability number, obtained from charts based on slope angle β \beta β and depth factor D d = D / H D_d = D/H D d = D / H (where D D D is the depth from top of slope to a hard rock stratum).
- Worked Engineering Calculation: Slope Stability Analysis
- Problem Statement
A permanent road cut slope is to be excavated in a saturated clay deposit at an angle of β = 30 ∘ \beta = 30^\circ β = 3 0 ∘ to a total vertical height H = 10.0 m H = 10.0\text{ m} H = 10.0 m . Field and laboratory testing indicate:
- Undrained shear strength c u = 45.0 kPa c_u = 45.0\text{ kPa} c u = 45.0 kPa
- Undrained friction angle ϕ u = 0 ∘ \phi_u = 0^\circ ϕ u = 0 ∘
- Total saturated unit weight γ s a t = 19.0 kN/m 3 \gamma_{sat} = 19.0\text{ kN/m}^3 γ s a t = 19.0 kN/m 3
A hard bedrock stratum lies at a depth of 15.0 m 15.0\text{ m} 15.0 m below the ground crest ( D = 15.0 m D = 15.0\text{ m} D = 15.0 m ).
Determine:
The depth factor D d D_d D d .
The Factor of Safety ( F S FS FS ) against short-term undrained failure using Taylor's stability chart value of N s = 0.160 N_s = 0.160 N s = 0.160 .
The maximum allowable slope height H m a x H_{max} H ma x if a minimum F S = 1.50 FS = 1.50 FS = 1.50 is required by design specifications.
Step-by-Step Solution
Step 1: Calculate the Depth Factor ( D d D_d D d ) D d = D H = 15.0 m 10.0 m = 1.50 D_d = \frac{D}{H} = \frac{15.0\text{ m}}{10.0\text{ m}} = 1.50 D d = H D = 10.0 m 15.0 m = 1.50
Step 2: Calculate the Short-Term Factor of Safety ( F S FS FS )
Using Taylor's equation F S = c u γ s a t H N s FS = \frac{c_u}{\gamma_{sat} H N_s} FS = γ s a t H N s c u : F S = 45.0 kPa ( 19.0 kN/m 3 ) × ( 10.0 m ) × 0.160 FS = \frac{45.0\text{ kPa}}{(19.0\text{ kN/m}^3) \times (10.0\text{ m}) \times 0.160} FS = ( 19.0 kN/m 3 ) × ( 10.0 m ) × 0.160 45.0 kPa F S = 45.0 30.40 = 1.48 FS = \frac{45.0}{30.40} = 1.48 FS = 30.40 45.0 = 1.48
Step 3: Calculate Maximum Allowable Slope Height ( H m a x H_{max} H ma x ) for F S = 1.50 FS = 1.50 FS = 1.50
Rearranging Taylor's formula for H H H with F S r e q = 1.50 FS_{req} = 1.50 F S re q = 1.50 : H m a x = c u γ s a t ⋅ F S r e q ⋅ N s H_{max} = \frac{c_u}{\gamma_{sat} \cdot FS_{req} \cdot N_s} H ma x = γ s a t ⋅ F S re q ⋅ N s c u H m a x = 45.0 kPa ( 19.0 kN/m 3 ) × 1.50 × 0.160 = 45.0 4.56 = 9.87 m H_{max} = \frac{45.0\text{ kPa}}{(19.0\text{ kN/m}^3) \times 1.50 \times 0.160} = \frac{45.0}{4.56} = 9.87\text{ m} H ma x = ( 19.0 kN/m 3 ) × 1.50 × 0.160 45.0 kPa = 4.56 45.0 = 9.87 m
Design Recommendation
Since the computed F S = 1.48 FS = 1.48 FS = 1.48 is slightly below the required F S r e q = 1.50 FS_{req} = 1.50 F S re q = 1.50 , the slope height must be trimmed to 9.87 m 9.87\text{ m} 9.87 m or the slope angle flattened to β = 26 ∘ \beta = 26^\circ β = 2 6 ∘ to lower N s N_s N s and satisfy civil infrastructure safety criteria.