Study guide
6.2 Flow Nets & Two-Dimensional Seepage Analysis
PE Civil Geotechnical Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Site Characterization
1.1 Site Data Interpretation & Boring Plans 1.2 In Situ Testing & Field Exploration 1.3 Soil and Rock Classification Systems 1.4 Groundwater Characterization & Hydrogeology
2 Chapter 2: Soil Mechanics, Laboratory Testing, and Analysis
2.1 Weight-Volume Phase Relationships & Index Properties 2.2 Effective Stress & Pore Water Pressure Dynamics 2.3 Shear Strength Principles & Laboratory Testing 2.4 Permeability, Hydraulic Conductivity & Seepage Properties 2.5 Consolidation & Compressibility Analysis
3 Chapter 3: Construction Observation, Monitoring, QA/QC, and Safety
3.1 Earthwork Quality Control & Compaction Verification 3.2 Geotechnical Instrumentation & Field Monitoring 3.3 Trenching, Excavation Safety & OSHA Shoring Requirements 3.4 Erosion, Scour Protection & Slope Protection During Construction
4 Chapter 4: Earthquake Engineering and Dynamic Loads
4.1 Seismic Site Characterization & Ground Motion Hazards 4.2 Soil Liquefaction Triggering & Post-Liquefaction Assessment 4.3 Dynamic Soil Properties & Ground Response Analysis 4.4 Pseudostatic Analysis & Seismic Geotechnical Design
5 Chapter 5: Earth Structures, Ground Improvement, and Pavement
5.1 Slope Stability Analysis & Limit Equilibrium Methods 5.2 Embankments, Earth Dams & Levee Geotechnics 5.3 Ground Improvement Techniques & Design 5.4 Geosynthetics in Geotechnical Engineering 5.5 Flexible & Rigid Pavement Subgrades & Buried Utilities 5.6 Landfills, Caps & Containment Systems
6 Chapter 6: Groundwater and Seepage
6.1 Dewatering System Design & Well Drawdown 6.2 Flow Nets & Two-Dimensional Seepage Analysis 6.3 Uplift Pressure, Piping & Heave Safety 6.4 Subsurface Drainage Systems & Filter Criteria
7 Chapter 7: Problematic Soil and Rock Conditions
7.1 Expansive & Collapsible Soil Engineering 7.2 Organic Soils, Sensitive Clays & Soft Marine Deposits 7.3 Corrosive, Frost-Susceptible & Degradable Formations 7.4 Karst Topography, Rock Slopes & Rockfall Hazards
8 Chapter 8: Retaining Structures
8.1 Lateral Earth Pressure Theories 8.2 Rigid Retaining Wall Design 8.3 Flexible Retaining Walls & Sheet Pile Bulkheads 8.4 Temporary Support of Excavations 8.5 Mechanically Stabilized Earth (MSE) Walls & Soil Nail Structures 8.6 Cofferdams, Underpinning & Adjacent Infrastructure Effects
9 Chapter 9: Shallow Foundations
9.1 Ultimate & Allowable Bearing Capacity Theories 9.2 Effective Footing Area, Eccentricity & Combined Footings 9.3 Induced Stress Distribution & Immediate Elastic Settlement 9.4 Consolidation Settlement & Mat/Raft Foundation Design
10 Chapter 10: Deep Foundations
10.1 Driven Pile Axial Capacity & Settlement 10.2 Drilled Shaft Axial Design & Construction Methods 10.3 Lateral Load Behavior of Deep Foundations 10.4 Pile Group Dynamics, Efficiency & Downdrag 10.5 Dynamic Load Testing & Pile Integrity Evaluation
6.2 Flow Nets & Two-Dimensional Seepage Analysis
Key Takeaways Explain This Topic AI
The total seepage discharge per unit length through isotropic soil is given by q = k ⋅ Δ H ⋅ N f N d q = k \cdot \Delta H \cdot \frac{N_f}{N_d} q = k ⋅ Δ H ⋅ N d N f , where N f N_f N f is the number of flow channels and N d N_d N d is the total number of equipotential drops.
Flow lines (paths of water particles) and equipotential lines (lines of equal total head) intersect orthogonally (90 degrees) to form curvilinear squares where width equals length (b = l).
The total head drop per equipotential drop is uniform across the flow net: Δ h = Δ H N d \Delta h = \frac{\Delta H}{N_d} Δ h = N d Δ H , where Δ H \Delta H Δ H is the net head difference across the hydraulic structure.
Pore water pressure at any node is determined by subtracting elevation head from total head: u = γ w ( h t − h z ) u = \gamma_w (h_t - h_z) u = γ w ( h t − h z ) .
For anisotropic soils ( k x ≠ k y k_x \neq k_y k x = k y ), physical coordinates must be transformed by scaling horizontal dimensions x ′ = x k y / k x x' = x \sqrt{k_y/k_x} x ′ = x k y / k x , and calculations use equivalent permeability k ′ = k x k y k' = \sqrt{k_x k_y} k ′ = k x k y .
Last updated: July 2026
- 6.2 Flow Nets & Two-Dimensional Seepage Analysis
- Governing Seepage Theory & Laplace Equation
Steady-state two-dimensional fluid flow through homogeneous, incompressible, saturated porous media is governed by Darcy's Law and the Continuity Equation . Assuming laminar flow and rigid soil skeleton, the volumetric water inflow equals outflow for an elemental control volume ( Δ x ⋅ Δ y ⋅ 1 ) (\Delta x \cdot \Delta y \cdot 1) ( Δ x ⋅ Δ y ⋅ 1 ) : ∂ v x ∂ x + ∂ v y ∂ y = 0 \frac{\partial v_x}{\partial x} + \frac{\partial v_y}{\partial y} = 0 ∂ x ∂ v x + ∂ y ∂ v y = 0
Substituting Darcy's velocities v x = − k x ∂ H ∂ x v_x = -k_x \frac{\partial H}{\partial x} v x = − k x ∂ x ∂ H and v y = − k y ∂ H ∂ y v_y = -k_y \frac{\partial H}{\partial y} v y = − k y ∂ y ∂ H yields the general 2D seepage equation: k x ∂ 2 H ∂ x 2 + k y ∂ 2 H ∂ y 2 = 0 k_x \frac{\partial^2 H}{\partial x^2} + k_y \frac{\partial^2 H}{\partial y^2} = 0 k x ∂ x 2 ∂ 2 H + k y ∂ y 2 ∂ 2 H = 0
For isotropic soils ( k x = k y = k k_x = k_y = k k x = k y = k ), this simplifies to Laplace's Differential Equation : ∂ 2 H ∂ x 2 + ∂ 2 H ∂ y 2 = 0 \frac{\partial^2 H}{\partial x^2} + \frac{\partial^2 H}{\partial y^2} = 0 ∂ x 2 ∂ 2 H + ∂ y 2 ∂ 2 H = 0
Where H = h p + h z = u γ w + z H = h_p + h_z = \frac{u}{\gamma_w} + z H = h p + h z = γ w u + z is total hydraulic head. Laplace's equation describes two orthogonal families of curves: Flow Lines (tangent to seepage velocity vectors) and Equipotential Lines (lines connecting points of equal total head H H H ).
Rules of Flow Net Construction & Boundary Conditions
A flow net is a graphical solution of Laplace's equation comprising a grid of flow lines and equipotential lines. Correct manual flow net construction requires strict adherence to physical boundary rules: UPSTREAM HEAD H1
- ~~~~~~~~~~~~~~~~~~~~~~~~~
- | |
- FLOW LINE 1 |-------------------- | SHEET PILE WALL
- | | |
- | EQUIPOTENTIAL | | DOWNSTREAM HEAD H2
- | DROPS | |~~~~~~~~~~~~~~~~~~~~~
- | +---+---+---+ | | |
- | | | | | | | | FLOW LINE 4
- |----|---|---|---|---|--|--|------------------>
- | | | | | | | |
- |====+===+===+===+===|==|==|==================
- IMPERMEABLE BEDROCK (FLOW LINE)
Boundary Types in Hydraulic Structures:
Impermeable Boundaries (Sheet pile surfaces, concrete dam bases, impervious bedrock): Water cannot cross; these surfaces form Flow Lines .
Permeable Ground Surfaces (Upstream submerged seabed/riverbed, downstream ground exit): Water enters or leaves soil at uniform total head; these surfaces form Equipotential Lines .
Phreatic / Free Water Table Lines (Unconfined seepage through earth dams): Forms the uppermost flow line, along which pore pressure is atmospheric ( u = 0 ⟹ H = z u = 0 \implies H = z u = 0 ⟹ H = z ).
Core Properties of Isotropic Flow Nets:
Orthogonality: Flow lines and equipotential lines intersect at exact 90 ∘ 90^\circ 9 0 ∘ angles everywhere.
Curvilinear Squares: The ratio of average element width b b b to element length l l l in flow direction is constant, usually drawn such that b / l ≈ 1.0 b/l \approx 1.0 b / l ≈ 1.0 .
Equal Head Drops: Total head loss Δ H \Delta H Δ H across the structure is divided into N d N_d N d equal equipotential drops: Δ h = Δ H N d \Delta h = \frac{\Delta H}{N_d} Δ h = N d Δ H
Equal Discharge per Channel: Total flow rate q q q is divided into N f N_f N f flow channels, each carrying equal discharge Δ q \Delta q Δ q .
Calculation of Total Seepage Discharge
For a single flow channel element of width b b b and length l l l , Darcy's Law gives: Δ q = k ⋅ i ⋅ A = k ⋅ ( Δ h l ) ⋅ ( b ⋅ 1 ) = k ⋅ Δ h ⋅ ( b l ) \Delta q = k \cdot i \cdot A = k \cdot \left(\frac{\Delta h}{l}\right) \cdot (b \cdot 1) = k \cdot \Delta h \cdot \left(\frac{b}{l}\right) Δ q = k ⋅ i ⋅ A = k ⋅ ( l Δ h ) ⋅ ( b ⋅ 1 ) = k ⋅ Δ h ⋅ ( l b )
Since Δ h = Δ H N d \Delta h = \frac{\Delta H}{N_d} Δ h = N d Δ H and for curvilinear squares b / l = 1.0 b/l = 1.0 b / l = 1.0 : Δ q = k ⋅ Δ H N d \Delta q = k \cdot \frac{\Delta H}{N_d} Δ q = k ⋅ N d Δ H
Summing across all N f N_f N f flow channels gives the fundamental Total Seepage Rate Formula per unit length of wall or dam: q = N f ⋅ Δ q = k ⋅ Δ H ⋅ N f N d q = N_f \cdot \Delta q = k \cdot \Delta H \cdot \frac{N_f}{N_d} q = N f ⋅ Δ q = k ⋅ Δ H ⋅ N d N f
Determining Pore Water Pressure and Hydraulic Gradients
To evaluate effective stress, uplifting forces, and stability against piping, total head H H H , elevation head h z h_z h z , and pore pressure u u u are computed at any node in the flow net.
Total Head ( h t h_t h t ) at Node n n n : Counting n n n equipotential drops from the upstream boundary (where h t , u p = H 1 h_{t,up} = H_1 h t , u p = H 1 ): h t , n = H 1 − n ⋅ Δ h = H 1 − n ⋅ ( Δ H N d ) h_{t,n} = H_1 - n \cdot \Delta h = H_1 - n \cdot \left(\frac{\Delta H}{N_d}\right) h t , n = H 1 − n ⋅ Δ h = H 1 − n ⋅ ( N d Δ H )
Elevation Head ( h z h_z h z ): Vertical height of the node above an arbitrary horizontal datum plane ( z = 0 z = 0 z = 0 ).
Pressure Head ( h p h_p h p ): h p = h t , n − h z h_p = h_{t,n} - h_z h p = h t , n − h z
Pore Water Pressure ( u u u ): u = γ w ⋅ h p = γ w ( h t , n − h z ) u = \gamma_w \cdot h_p = \gamma_w \left(h_{t,n} - h_z\right) u = γ w ⋅ h p = γ w ( h t , n − h z )
Local Hydraulic Gradient ( i j i_j i j ): In field element j j j of length l j l_j l j : i j = Δ h l j = Δ H / N d l j i_j = \frac{\Delta h}{l_j} = \frac{\Delta H / N_d}{l_j} i j = l j Δ h = l j Δ H / N d
Seepage in Anisotropic Soil Deposits ( k x ≠ k y k_x \neq k_y k x = k y )
Natural sedimentary soils frequently exhibit horizontal permeability k x k_x k x greater than vertical permeability k y k_y k y ( k x / k y k_x / k_y k x / k y typically ranges from 2 to 10). Seepage through anisotropic media is solved by transforming the physical section into an equivalent isotropic section.
Transformation Rules:
Horizontal Coordinate Scaling: Scale horizontal physical dimensions x x x by factor k y / k x \sqrt{k_y / k_x} k y / k x : x ′ = x ⋅ k y k x , y ′ = y x' = x \cdot \sqrt{\frac{k_y}{k_x}}, \quad y' = y x ′ = x ⋅ k x k y , y ′ = y
Equivalent Isotropic Hydraulic Conductivity ( k ′ k' k ′ ): Use k ′ k' k ′ in the standard seepage formula: k ′ = k x ⋅ k y k' = \sqrt{k_x \cdot k_y} k ′ = k x ⋅ k y
Seepage Rate Formula for Transformed Section: q = k ′ ⋅ Δ H ⋅ N f N d = k x ⋅ k y ⋅ Δ H ⋅ N f N d q = k' \cdot \Delta H \cdot \frac{N_f}{N_d} = \sqrt{k_x \cdot k_y} \cdot \Delta H \cdot \frac{N_f}{N_d} q = k ′ ⋅ Δ H ⋅ N d N f = k x ⋅ k y ⋅ Δ H ⋅ N d N f
Note on Geometrical Intersections: In the transformed ( x ′ , y ′ ) (x', y') ( x ′ , y ′ ) drawing, flow lines and equipotential lines intersect at 90 ∘ 90^\circ 9 0 ∘ forming curvilinear squares. When transferred back to the true scale physical drawing ( x , y ) (x, y) ( x , y ) , lines do not intersect at 90 ∘ 90^\circ 9 0 ∘ unless k x = k y k_x = k_y k x = k y .
- Worked Numerical Examples
- Worked Example 1: Seepage Discharge & Uplift under Dam
Problem Statement: A concrete dam is founded on an isotropic sand layer ( k = 3.5 × 10 − 5 m/s k = 3.5 \times 10^{-5}\text{ m/s} k = 3.5 × 1 0 − 5 m/s ). Upstream head H 1 = 10.0 m H_1 = 10.0\text{ m} H 1 = 10.0 m above riverbed; downstream head H 2 = 1.0 m H_2 = 1.0\text{ m} H 2 = 1.0 m (net head Δ H = 9.0 m \Delta H = 9.0\text{ m} Δ H = 9.0 m ). A flow net has N f = 4 N_f = 4 N f = 4 flow channels and N d = 12 N_d = 12 N d = 12 equipotential drops. Point A lies on the dam base at elevation z = − 2.5 m z = -2.5\text{ m} z = − 2.5 m relative to downstream riverbed ( z = 0 z=0 z = 0 ) along the 4th equipotential line (counted from upstream). Calculate:
Seepage discharge per meter length per day ( q q q ).
Pore water pressure u u u at Point A (take γ w = 9.81 kN/m 3 \gamma_w = 9.81\text{ kN/m}^3 γ w = 9.81 kN/m 3 ).
Solution:
Calculate daily seepage rate q q q per unit length: q = k ⋅ Δ H ⋅ N f N d = ( 3.5 × 10 − 5 m/s ) × ( 9.0 m ) × ( 4 12 ) = 1.05 × 10 − 4 m 3 / s/m q = k \cdot \Delta H \cdot \frac{N_f}{N_d} = (3.5 \times 10^{-5}\text{ m/s}) \times (9.0\text{ m}) \times \left(\frac{4}{12}\right) = 1.05 \times 10^{-4}\text{ m}^3/\text{s/m} q = k ⋅ Δ H ⋅ N d N f = ( 3.5 × 1 0 − 5 m/s ) × ( 9.0 m ) × ( 12 4 ) = 1.05 × 1 0 − 4 m 3 / s/m
Convert to m 3 / day/m \text{m}^3/\text{day/m} m 3 / day/m ( 86 , 400 s/day 86,400\text{ s/day} 86 , 400 s/day ): q = 1.05 × 10 − 4 × 86 , 400 = 9.072 m 3 / day/m q = 1.05 \times 10^{-4} \times 86,400 = 9.072\text{ m}^3/\text{day/m} q = 1.05 × 1 0 − 4 × 86 , 400 = 9.072 m 3 / day/m
Calculate pore water pressure at Point A:
Head loss per drop: Δ h = Δ H N d = 9.0 m 12 = 0.75 m \Delta h = \frac{\Delta H}{N_d} = \frac{9.0\text{ m}}{12} = 0.75\text{ m} Δ h = N d Δ H = 12 9.0 m = 0.75 m
Total head at upstream riverbed: H 1 = 10.0 m H_1 = 10.0\text{ m} H 1 = 10.0 m
Total head at Point A ( n = 4 n = 4 n = 4 drops): h t , A = 10.0 − 4 × ( 0.75 ) = 7.0 m h_{t,A} = 10.0 - 4 \times (0.75) = 7.0\text{ m} h t , A = 10.0 − 4 × ( 0.75 ) = 7.0 m
Elevation head at Point A: h z = − 2.5 m h_z = -2.5\text{ m} h z = − 2.5 m
Pressure head at Point A: h p = h t , A − h z = 7.0 − ( − 2.5 ) = 9.5 m h_p = h_{t,A} - h_z = 7.0 - (-2.5) = 9.5\text{ m} h p = h t , A − h z = 7.0 − ( − 2.5 ) = 9.5 m
Pore pressure at Point A: u = γ w ⋅ h p = 9.81 kN/m 3 × 9.5 m = 93.20 kPa u = \gamma_w \cdot h_p = 9.81\text{ kN/m}^3 \times 9.5\text{ m} = 93.20\text{ kPa} u = γ w ⋅ h p = 9.81 kN/m 3 × 9.5 m = 93.20 kPa