Study guide
7.4 Karst Topography, Rock Slopes & Rockfall Hazards
PE Civil Geotechnical Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Site Characterization
1.1 Site Data Interpretation & Boring Plans 1.2 In Situ Testing & Field Exploration 1.3 Soil and Rock Classification Systems 1.4 Groundwater Characterization & Hydrogeology
2 Chapter 2: Soil Mechanics, Laboratory Testing, and Analysis
2.1 Weight-Volume Phase Relationships & Index Properties 2.2 Effective Stress & Pore Water Pressure Dynamics 2.3 Shear Strength Principles & Laboratory Testing 2.4 Permeability, Hydraulic Conductivity & Seepage Properties 2.5 Consolidation & Compressibility Analysis
3 Chapter 3: Construction Observation, Monitoring, QA/QC, and Safety
3.1 Earthwork Quality Control & Compaction Verification 3.2 Geotechnical Instrumentation & Field Monitoring 3.3 Trenching, Excavation Safety & OSHA Shoring Requirements 3.4 Erosion, Scour Protection & Slope Protection During Construction
4 Chapter 4: Earthquake Engineering and Dynamic Loads
4.1 Seismic Site Characterization & Ground Motion Hazards 4.2 Soil Liquefaction Triggering & Post-Liquefaction Assessment 4.3 Dynamic Soil Properties & Ground Response Analysis 4.4 Pseudostatic Analysis & Seismic Geotechnical Design
5 Chapter 5: Earth Structures, Ground Improvement, and Pavement
5.1 Slope Stability Analysis & Limit Equilibrium Methods 5.2 Embankments, Earth Dams & Levee Geotechnics 5.3 Ground Improvement Techniques & Design 5.4 Geosynthetics in Geotechnical Engineering 5.5 Flexible & Rigid Pavement Subgrades & Buried Utilities 5.6 Landfills, Caps & Containment Systems
6 Chapter 6: Groundwater and Seepage
6.1 Dewatering System Design & Well Drawdown 6.2 Flow Nets & Two-Dimensional Seepage Analysis 6.3 Uplift Pressure, Piping & Heave Safety 6.4 Subsurface Drainage Systems & Filter Criteria
7 Chapter 7: Problematic Soil and Rock Conditions
7.1 Expansive & Collapsible Soil Engineering 7.2 Organic Soils, Sensitive Clays & Soft Marine Deposits 7.3 Corrosive, Frost-Susceptible & Degradable Formations 7.4 Karst Topography, Rock Slopes & Rockfall Hazards
8 Chapter 8: Retaining Structures
8.1 Lateral Earth Pressure Theories 8.2 Rigid Retaining Wall Design 8.3 Flexible Retaining Walls & Sheet Pile Bulkheads 8.4 Temporary Support of Excavations 8.5 Mechanically Stabilized Earth (MSE) Walls & Soil Nail Structures 8.6 Cofferdams, Underpinning & Adjacent Infrastructure Effects
9 Chapter 9: Shallow Foundations
9.1 Ultimate & Allowable Bearing Capacity Theories 9.2 Effective Footing Area, Eccentricity & Combined Footings 9.3 Induced Stress Distribution & Immediate Elastic Settlement 9.4 Consolidation Settlement & Mat/Raft Foundation Design
10 Chapter 10: Deep Foundations
10.1 Driven Pile Axial Capacity & Settlement 10.2 Drilled Shaft Axial Design & Construction Methods 10.3 Lateral Load Behavior of Deep Foundations 10.4 Pile Group Dynamics, Efficiency & Downdrag 10.5 Dynamic Load Testing & Pile Integrity Evaluation
7.4 Karst Topography, Rock Slopes & Rockfall Hazards
Key Takeaways Explain This Topic AI
Karst hazards stem from chemical dissolution of carbonate and evaporite rocks, creating cover-collapse, cover-subsidence, and solution sinkholes that require geophysical detection (ERT, GPR) and compaction/cap grouting.
Rock slope stability is dictated by geological structural discontinuities, classifying failure into planar, wedge, toppling, and circular modes using kinematic stereonet analysis.
Limit equilibrium stability equations incorporate joint cohesion, friction angle, joint water uplift pressure (U), tension crack water pressure (V), and non-linear joint shear strength (Barton-Bandis model).
Kinematic stability requires specific angular relationships between slope face dip (ψf), failure plane dip (ψp), line of intersection plunge (ψi), and joint friction angle (ϕ').
Rockfall hazard mitigation involves energy-rated flexible catch nets, draped high-tensile wire mesh, rock bolts, tensioned anchors, shotcrete, and ditch catchment geometry based on kinetic energy dynamics.
Last updated: July 2026
7.4 Karst Topography, Rock Slopes & Rockfall Hazards
Geotechnical engineering in rock formations presents distinct hazards associated with karst terrain dissolution , rock slope instability , and rockfall hazards . Unlike soils, rock masses are strongly anisotropic, dominated by geological discontinuities (joints, bedding planes, faults). PE Civil examinees must be proficient in sinkhole genetic mechanisms, geophysical exploration, kinematic stereonet analysis, limit equilibrium stability equations for jointed rock blocks, and kinetic energy rockfall protection systems.
- 1. Karst Topography & Sinkhole Mechanics
- Chemical Dissolution Reactions
Karst topography develops through chemical weathering of soluble bedrock, primarily carbonate rocks ( limestone , CaCO 3 \text{CaCO}_3 CaCO 3 ; dolomite , CaMg(CO 3 ) 2 \text{CaMg(CO}_3)_2 CaMg(CO 3 ) 2 ) and evaporites ( gypsum , CaSO 4 ⋅ 2 H 2 O \text{CaSO}_4\cdot 2\text{H}_2\text{O} CaSO 4 ⋅ 2 H 2 O ; rock salt , NaCl \text{NaCl} NaCl ). Carbonate dissolution is driven by carbonic acid formed when rainwater absorbs atmospheric and soil CO 2 \text{CO}_2 CO 2 : CaCO 3 + H 2 O + CO 2 ⇌ Ca 2 + + 2 HCO 3 − \text{CaCO}_3 + \text{H}_2\text{O} + \text{CO}_2 \rightleftharpoons \text{Ca}^{2+} + 2\text{HCO}_3^- CaCO 3 + H 2 O + CO 2 ⇌ Ca 2 + + 2 HCO 3 −
This dissolution expands rock joints into underground conduits, caves, and pinnacled bedrock profiles.
Genetic Sinkhole Classifications
Cover-Collapse Sinkhole: The most catastrophic hazard. Cohesive overburden clay bridges across a bedrock void. Percolating water erodes the roof internally, forming a dome-shaped cavity that migrates upward until the soil roof collapses abruptly into the bedrock cavern.
Cover-Subsidence Sinkhole: Occurs in non-cohesive sandy overburden. Sand continuously pipes downward into small bedrock fissures, producing gradual ground surface depressions.
Solution Sinkhole: Bedrock exposed directly at the ground surface dissolves uniformly along joints, creating shallow bowl-shaped depressions.
Geophysical Void Exploration & Remediation
Electrical Resistivity Tomography (ERT): Identifies air-filled cavities (very high resistivity) or clay-filled voids (very low resistivity).
Ground Penetrating Radar (GPR): Maps shallow soil piping and shallow void roofs ( < 5 − 10 m < 5 - 10\text{ m} < 5 − 10 m depth).
Microgravity Surveys: Detects localized subsurface mass deficits caused by deep caverns.
Remediation Techniques: Low-slump compaction grouting ( 50 to 100 mm 50\text{ to }100\text{ mm} 50 to 100 mm slump under high pressure) to densify soil, cap grouting across bedrock openings, and high-capacity micropiles drilled into sound bedrock.
2. Rock Slope Failure Modes & Kinematic Criteria
Stability of rock slopes is dictated by joint orientation relative to the slope face. Kinematic analysis uses stereographic projections (stereonets) to determine feasible failure modes: ROCK SLOPE FAILURE MODES
- ┌──────────────────┬──────────────────┬──────────────────┬──────────────────┐
- │ Planar Failure │ Wedge Failure │ Toppling Failure │ Circular Failure │
- ├──────────────────┼──────────────────┼──────────────────┼──────────────────┤
- │ Single continuous│ Intersection line│ Steep joints dip │ Heavily jointed │
- │ joint plane dips │ of 2 joint planes│ INTO slope face; │ rock mass or soil│
- │ OUT of slope face│ plunges OUT face │ layers tilt out │ like weak rock │
- └──────────────────┴──────────────────┴──────────────────┴──────────────────┘
- Kinematic Conditions for Failure
Planar Failure Kinematic Criteria:
The strike of the planar joint must be within ± 20 ∘ \pm 20^\circ ± 2 0 ∘ of the slope face strike.
The joint dip ( ψ p \psi_p ψ p ) must be less than the slope face dip ( ψ f \psi_f ψ f ) (joint daylighting): ψ p < ψ f \psi_p < \psi_f ψ p < ψ f .
The joint dip must exceed the friction angle of the joint surface ( ϕ ′ \phi' ϕ ′ ): ψ p > ϕ ′ \psi_p > \phi' ψ p > ϕ ′ . ψ f > ψ p > ϕ ′ \psi_f > \psi_p > \phi' ψ f > ψ p > ϕ ′
Wedge Failure Kinematic Criteria: The plunge of the intersection line ( ψ i \psi_i ψ i ) of two joint planes must daylight on the slope face and exceed the joint friction angle: ψ f > ψ i > ϕ ′ \psi_f > \psi_i > \phi' ψ f > ψ i > ϕ ′
Toppling Failure Kinematic Criteria: Joints dip steeply into the slope face. Toppling initiates when the joint dip ( ψ j \psi_j ψ j ) satisfies: ψ j ≥ ( 90 ∘ − ψ f ) + ϕ ′ \psi_j \ge (90^\circ - \psi_f) + \phi' ψ j ≥ ( 9 0 ∘ − ψ f ) + ϕ ′
- 3. Limit Equilibrium Analysis & Joint Mechanics
- Barton-Bandis Joint Shear Strength Model
For un-grouted rock discontinuities, shear strength is highly non-linear, modeled via the Barton-Bandis Equation : τ = σ n ′ ⋅ tan [ J R C ⋅ log 10 ( J C S σ n ′ ) + ϕ b ] \tau = \sigma'_n \cdot \tan \left[ JRC \cdot \log_{10}\left( \frac{JCS}{\sigma'_n} \right) + \phi_b \right] τ = σ n ′ ⋅ tan [ J RC ⋅ lo g 10 ( σ n ′ J CS ) + ϕ b ]
where J R C JRC J RC is Joint Roughness Coefficient ( 0 to 20 0\text{ to }20 0 to 20 ), J C S JCS J CS is Joint Wall Compressive Strength, σ n ′ \sigma'_n σ n ′ is effective normal stress, and ϕ b \phi_b ϕ b is basic friction angle.
Factor of Safety Equation for Planar Rock Slope
For a rock block resting on a planar slip surface of length A A A with joint cohesion c ′ c' c ′ , friction angle ϕ ′ \phi' ϕ ′ , joint uplift water force U U U , tension crack water force V V V , and tensioned rockbolt capacity T T T inclined at angle θ \theta θ below horizontal: F S = c ′ A + [ W cos ψ p − U − V sin ψ p + T sin ( θ + ψ p ) ] tan ϕ ′ W sin ψ p + V cos ψ p − T cos ( θ + ψ p ) FS = \frac{c' A + \left[ W \cos\psi_p - U - V \sin\psi_p + T \sin(\theta + \psi_p) \right] \tan\phi'}{W \sin\psi_p + V \cos\psi_p - T \cos(\theta + \psi_p)} FS = W sin ψ p + V cos ψ p − T cos ( θ + ψ p ) c ′ A + [ W cos ψ p − U − V sin ψ p + T sin ( θ + ψ p ) ] tan ϕ ′ V (Tension Crack Water)
- │
- ▼
- ┌──────────────┐
- │ ROCK │
- │ BLOCK │ ══► T (Rockbolt Tension)
- │ (Weight W) │
- └──────────────┘
- ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ <-- Joint Plane (Dip ψp)
- ▲
- │
- U (Uplift Water Pressure)
- 4. Rockfall Mechanics & Hazard Mitigation
- Kinetic Energy Dynamics
Rockfall hazard intensity is dictated by total kinetic energy ( E k E_k E k ), combining translational and rotational components: E k = E t r a n s + E r o t = 1 2 m v 2 + 1 2 I ω 2 E_k = E_{trans} + E_{rot} = \frac{1}{2} m v^2 + \frac{1}{2} I \omega^2 E k = E t r an s + E ro t = 2 1 m v 2 + 2 1 I ω 2
where m m m is rock mass, v v v is translational velocity, I I I is mass moment of inertia, and ω \omega ω is rotational velocity.
Protection Mitigation Systems
High-Capacity Flexible Catch Fences: Dynamic net barriers rated from 500 to 10 , 000 kJ 500\text{ to }10,000\text{ kJ} 500 to 10 , 000 kJ impact capacity featuring energy-dissipating friction rings.
Draped High-Tensile Steel Wire Mesh: Wire mesh (e.g., Tecco mesh) anchored at the crest, controlling rockfall trajectories and guiding detached rocks safely into a ditch.
Catchment Ditches & Berms (Ritchie Criteria): Ditch depth ( D d i t c h D_{ditch} D d i t c h ) and width ( W d i t c h W_{ditch} W d i t c h ) sized as a function of slope height ( H s l o p e H_{slope} H s l o p e ) and slope angle to contain bouncing rocks.
Pattern Rock Bolting & Shotcrete: Active fully-grouted rock bolts preventing initial block detachment.
Loading diagram... Classification of Rock Slope Failure Modes and Kinematic Criteria
- 5. Comprehensive Worked Engineering Example
- Problem Statement
A highway rock cut is excavated in sandstone at a slope face angle ψ f = 60 ∘ \psi_f = 60^\circ ψ f = 6 0 ∘ . Geological mapping identifies a continuous bedding plane discontinuity dipping out of the slope face at ψ p = 36 ∘ \psi_p = 36^\circ ψ p = 3 6 ∘ . A vertical tension crack is present at the slope crest. Geotechnical data per unit width ( 1.0 m 1.0\text{ m} 1.0 m ) are as follows:
- Rock block weight W = 900.0 kN/m W = 900.0\text{ kN/m} W = 900.0 kN/m
- Joint plane base area A = 14.0 m 2 / m A = 14.0\text{ m}^2/\text{m} A = 14.0 m 2 / m
- Joint cohesion c ′ = 25.0 kPa c' = 25.0\text{ kPa} c ′ = 25.0 kPa
- Joint friction angle ϕ ′ = 30.0 ∘ \phi' = 30.0^\circ ϕ ′ = 30. 0 ∘
- Calculated joint uplift water force U = 180.0 kN/m U = 180.0\text{ kN/m} U = 180.0 kN/m
- Calculated tension crack water force V = 50.0 kN/m V = 50.0\text{ kN/m} V = 50.0 kN/m
Required:
Calculate the unreinforced Factor of Safety ( F S u n r e i n f o r c e d FS_{unreinforced} F S u n re in f orce d ) against planar sliding along the joint.
Determine if the slope meets the required design stability standard of F S ≥ 1.50 FS \ge 1.50 FS ≥ 1.50 .
Calculate the required rockbolt tension capacity ( T T T ) per meter of wall width to achieve F S = 1.50 FS = 1.50 FS = 1.50 , assuming pattern rock bolts are installed at an inclination θ = 14 ∘ \theta = 14^\circ θ = 1 4 ∘ below horizontal.
- Step-by-Step Calculation Solution
- Step 1: Unreinforced Factor of Safety Calculation
Compute statutory geometric trigonometric values:
- sin ( 36 ∘ ) = 0.58779 \sin(36^\circ) = 0.58779 sin ( 3 6 ∘ ) = 0.58779
- cos ( 36 ∘ ) = 0.80902 \cos(36^\circ) = 0.80902 cos ( 3 6 ∘ ) = 0.80902
- tan ( 30 ∘ ) = 0.57735 \tan(30^\circ) = 0.57735 tan ( 3 0 ∘ ) = 0.57735
Calculate total driving force ( D D D ) down the slip plane: D = W sin ψ p + V cos ψ p D = W \sin\psi_p + V \cos\psi_p D = W sin ψ p + V cos ψ p D = ( 900.0 × 0.58779 ) + ( 50.0 × 0.80902 ) = 529.01 + 40.45 = 569.46 kN/m D = (900.0 \times 0.58779) + (50.0 \times 0.80902) = 529.01 + 40.45 = 569.46\text{ kN/m} D = ( 900.0 × 0.58779 ) + ( 50.0 × 0.80902 ) = 529.01 + 40.45 = 569.46 kN/m
Calculate net effective normal force ( N ′ N' N ′ ) acting perpendicular to the slip plane: N ′ = W cos ψ p − U − V sin ψ p N' = W \cos\psi_p - U - V \sin\psi_p N ′ = W cos ψ p − U − V sin ψ p N ′ = ( 900.0 × 0.80902 ) − 180.0 − ( 50.0 × 0.58779 ) N' = (900.0 \times 0.80902) - 180.0 - (50.0 \times 0.58779) N ′ = ( 900.0 × 0.80902 ) − 180.0 − ( 50.0 × 0.58779 ) N ′ = 728.12 − 180.0 − 29.39 = 518.73 kN/m N' = 728.12 - 180.0 - 29.39 = 518.73\text{ kN/m} N ′ = 728.12 − 180.0 − 29.39 = 518.73 kN/m
Calculate available shear resistance ( R R R ) along the slip plane: R = c ′ A + N ′ tan ϕ ′ R = c' A + N' \tan\phi' R = c ′ A + N ′ tan ϕ ′ R = ( 25.0 kPa × 14.0 m 2 / m ) + ( 518.73 kN/m × 0.57735 ) R = (25.0\text{ kPa} \times 14.0\text{ m}^2/\text{m}) + (518.73\text{ kN/m} \times 0.57735) R = ( 25.0 kPa × 14.0 m 2 / m ) + ( 518.73 kN/m × 0.57735 ) R = 350.0 + 299.49 = 649.49 kN/m R = 350.0 + 299.49 = 649.49\text{ kN/m} R = 350.0 + 299.49 = 649.49 kN/m
Calculate Unreinforced Factor of Safety ( F S u n r e i n f o r c e d FS_{unreinforced} F S u n re in f orce d ): F S u n r e i n f o r c e d = R D = 649.49 kN/m 569.46 kN/m = 1.140 FS_{unreinforced} = \frac{R}{D} = \frac{649.49\text{ kN/m}}{569.46\text{ kN/m}} = 1.140 F S u n re in f orce d = D R = 569.46 kN/m 649.49 kN/m = 1.140
Step 2: Evaluation Against Design Standard
Since F S u n r e i n f o r c e d = 1.140 < 1.50 FS_{unreinforced} = 1.140 < 1.50 F S u n re in f orce d = 1.140 < 1.50 , the unreinforced rock cut is unstable and presents an unacceptable hazard for highway operations. Structural rockbolt reinforcement is required.
Step 3: Required Rockbolt Tension Capacity ( T T T ) for F S = 1.50 FS = 1.50 FS = 1.50
Rockbolts are inclined at θ = 14 ∘ \theta = 14^\circ θ = 1 4 ∘ below horizontal.
Angle between rockbolt force T T T and failure plane: θ + ψ p = 14 ∘ + 36 ∘ = 50 ∘ \theta + \psi_p = 14^\circ + 36^\circ = 50^\circ θ + ψ p = 1 4 ∘ + 3 6 ∘ = 5 0 ∘ .
- sin ( 50 ∘ ) = 0.76604 \sin(50^\circ) = 0.76604 sin ( 5 0 ∘ ) = 0.76604
- cos ( 50 ∘ ) = 0.64279 \cos(50^\circ) = 0.64279 cos ( 5 0 ∘ ) = 0.64279
Set up the reinforced Factor of Safety equation with F S = 1.50 FS = 1.50 FS = 1.50 : F S = 1.50 = R u n r e i n f o r c e d + T sin ( θ + ψ p ) tan ϕ ′ D u n r e i n f o r c e d − T cos ( θ + ψ p ) FS = 1.50 = \frac{R_{unreinforced} + T \sin(\theta + \psi_p) \tan\phi'}{D_{unreinforced} - T \cos(\theta + \psi_p)} FS = 1.50 = D u n re in f orce d − T cos ( θ + ψ p ) R u n re in f orce d + T sin ( θ + ψ p ) tan ϕ ′ 1.50 = 649.49 + T ( 0.76604 × 0.57735 ) 569.46 − T ( 0.64279 ) 1.50 = \frac{649.49 + T (0.76604 \times 0.57735)}{569.46 - T (0.64279)} 1.50 = 569.46 − T ( 0.64279 ) 649.49 + T ( 0.76604 × 0.57735 ) 1.50 = 649.49 + 0.44227 T 569.46 − 0.64279 T 1.50 = \frac{649.49 + 0.44227 T}{569.46 - 0.64279 T} 1.50 = 569.46 − 0.64279 T 649.49 + 0.44227 T
Multiply both sides by ( 569.46 − 0.64279 T ) (569.46 - 0.64279 T) ( 569.46 − 0.64279 T ) : 1.50 × ( 569.46 − 0.64279 T ) = 649.49 + 0.44227 T 1.50 \times (569.46 - 0.64279 T) = 649.49 + 0.44227 T 1.50 × ( 569.46 − 0.64279 T ) = 649.49 + 0.44227 T 854.19 − 0.96419 T = 649.49 + 0.44227 T 854.19 - 0.96419 T = 649.49 + 0.44227 T 854.19 − 0.96419 T = 649.49 + 0.44227 T
Rearrange terms to isolate T T T : 854.19 − 649.49 = 0.44227 T + 0.96419 T 854.19 - 649.49 = 0.44227 T + 0.96419 T 854.19 − 649.49 = 0.44227 T + 0.96419 T 204.70 = 1.40646 T 204.70 = 1.40646 T 204.70 = 1.40646 T T = 204.70 1.40646 = 145.54 kN/m T = \frac{204.70}{1.40646} = 145.54\text{ kN/m} T = 1.40646 204.70 = 145.54 kN/m
Engineering Conclusion: Installing tensioned rock bolts providing a minimum structural capacity T = 146 kN/m T = 146\text{ kN/m} T = 146 kN/m inclined at 14 ∘ 14^\circ 1 4 ∘ below horizontal increases the planar rock slope Factor of Safety to the target design standard of F S = 1.50 FS = 1.50 FS = 1.50 .