Study guide
8.2 Rigid Retaining Wall Design
PE Civil Geotechnical Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Site Characterization
1.1 Site Data Interpretation & Boring Plans 1.2 In Situ Testing & Field Exploration 1.3 Soil and Rock Classification Systems 1.4 Groundwater Characterization & Hydrogeology
2 Chapter 2: Soil Mechanics, Laboratory Testing, and Analysis
2.1 Weight-Volume Phase Relationships & Index Properties 2.2 Effective Stress & Pore Water Pressure Dynamics 2.3 Shear Strength Principles & Laboratory Testing 2.4 Permeability, Hydraulic Conductivity & Seepage Properties 2.5 Consolidation & Compressibility Analysis
3 Chapter 3: Construction Observation, Monitoring, QA/QC, and Safety
3.1 Earthwork Quality Control & Compaction Verification 3.2 Geotechnical Instrumentation & Field Monitoring 3.3 Trenching, Excavation Safety & OSHA Shoring Requirements 3.4 Erosion, Scour Protection & Slope Protection During Construction
4 Chapter 4: Earthquake Engineering and Dynamic Loads
4.1 Seismic Site Characterization & Ground Motion Hazards 4.2 Soil Liquefaction Triggering & Post-Liquefaction Assessment 4.3 Dynamic Soil Properties & Ground Response Analysis 4.4 Pseudostatic Analysis & Seismic Geotechnical Design
5 Chapter 5: Earth Structures, Ground Improvement, and Pavement
5.1 Slope Stability Analysis & Limit Equilibrium Methods 5.2 Embankments, Earth Dams & Levee Geotechnics 5.3 Ground Improvement Techniques & Design 5.4 Geosynthetics in Geotechnical Engineering 5.5 Flexible & Rigid Pavement Subgrades & Buried Utilities 5.6 Landfills, Caps & Containment Systems
6 Chapter 6: Groundwater and Seepage
6.1 Dewatering System Design & Well Drawdown 6.2 Flow Nets & Two-Dimensional Seepage Analysis 6.3 Uplift Pressure, Piping & Heave Safety 6.4 Subsurface Drainage Systems & Filter Criteria
7 Chapter 7: Problematic Soil and Rock Conditions
7.1 Expansive & Collapsible Soil Engineering 7.2 Organic Soils, Sensitive Clays & Soft Marine Deposits 7.3 Corrosive, Frost-Susceptible & Degradable Formations 7.4 Karst Topography, Rock Slopes & Rockfall Hazards
8 Chapter 8: Retaining Structures
8.1 Lateral Earth Pressure Theories 8.2 Rigid Retaining Wall Design 8.3 Flexible Retaining Walls & Sheet Pile Bulkheads 8.4 Temporary Support of Excavations 8.5 Mechanically Stabilized Earth (MSE) Walls & Soil Nail Structures 8.6 Cofferdams, Underpinning & Adjacent Infrastructure Effects
9 Chapter 9: Shallow Foundations
9.1 Ultimate & Allowable Bearing Capacity Theories 9.2 Effective Footing Area, Eccentricity & Combined Footings 9.3 Induced Stress Distribution & Immediate Elastic Settlement 9.4 Consolidation Settlement & Mat/Raft Foundation Design
10 Chapter 10: Deep Foundations
10.1 Driven Pile Axial Capacity & Settlement 10.2 Drilled Shaft Axial Design & Construction Methods 10.3 Lateral Load Behavior of Deep Foundations 10.4 Pile Group Dynamics, Efficiency & Downdrag 10.5 Dynamic Load Testing & Pile Integrity Evaluation
8.2 Rigid Retaining Wall Design
Key Takeaways Explain This Topic AI
Rigid retaining walls (gravity, cantilever, counterfort) must satisfy external stability requirements against sliding ( FS ≥ 1.5 \text{FS} \ge 1.5 FS ≥ 1.5 ), overturning ( FS ≥ 2.0 \text{FS} \ge 2.0 FS ≥ 2.0 ), and bearing capacity failure ( FS ≥ 3.0 \text{FS} \ge 3.0 FS ≥ 3.0 ).
The resultant base force eccentricity must remain within the middle third of the foundation footprint ( e ≤ B / 6 e \le B/6 e ≤ B /6 ) to prevent tensile stresses at the heel-soil interface.
Shear keys placed underneath the base slab mobilize passive soil resistance and increase frictional resistance on weak foundation soils to satisfy sliding criteria.
Stem, toe slab, and heel slab are designed internally as reinforced concrete cantilever structural members under factored load combinations (e.g., AASHTO LRFD Strength I).
Effective wall drainage systems (weep holes, back-of-wall gravel drains, geotextile filters, prefabricated drainage panels) prevent destructive hydrostatic pressure buildup.
Last updated: July 2026
Classification and Geometry Proportioning of Rigid Walls
Rigid retaining walls rely on their self-weight and structural rigidity to resist lateral forces from retained soil masses. They are categorized into four principal structural types:
Gravity Walls: Mass concrete or stone masonry structures that rely entirely on dead weight to resist overturning and sliding. Economical for heights up to H ≈ 3.0 − 4.0 m H \approx 3.0 - 4.0\text{ m} H ≈ 3.0 − 4.0 m .
Semi-Gravity Walls: Mass concrete sections incorporating small amounts of steel reinforcement to reduce concrete volume.
Cantilever Walls: Reinforced concrete structures consisting of a thin vertical stem and a horizontal base slab (divided into a toe and a heel). Economical for heights H ≈ 3.0 − 8.0 m H \approx 3.0 - 8.0\text{ m} H ≈ 3.0 − 8.0 m .
Counterfort Walls: Reinforced concrete walls featuring thin transverse concrete ribs (counterforts) connecting the stem to the heel slab at regular intervals ( 2.0 − 4.0 m 2.0 - 4.0\text{ m} 2.0 − 4.0 m spacing). Counterforts act as tension ties to reduce flexural bending moments in the stem for heights H > 7.0 − 8.0 m H > 7.0 - 8.0\text{ m} H > 7.0 − 8.0 m .
Typical Proportioning Guidelines for Cantilever Walls
Before performing stability checks, wall dimensions are selected using empirical rules of thumb:
- Base width: B ≈ 0.50 H to 0.70 H B \approx 0.50 H \text{ to } 0.70 H B ≈ 0.50 H to 0.70 H
- Toe projection: A ≈ 0.10 H to 0.33 B A \approx 0.10 H \text{ to } 0.33 B A ≈ 0.10 H to 0.33 B
- Base slab thickness: D f ≈ 0.10 H D_f \approx 0.10 H D f ≈ 0.10 H (minimum 0.30 m 0.30\text{ m} 0.30 m )
Stem thickness at top: Minimum 0.30 m 0.30\text{ m} 0.30 m (tapered downward at 1 : 48 1:48 1 : 48 or 1 : 24 1:24 1 : 24 batter)
External Stability Analysis (Allowable Stress Design Framework)
External stability checks ensure the retaining wall acts as a safe rigid body relative to the underlying foundation soil. Three collapse modes and one serviceability criterion must be satisfied under Allowable Stress Design (ASD): | q (Surcharge)
- v
- |========|
- | Soil |
- STEM | Weight |
- || | (W_s) | P_ah (Active Thrust)
- || | | <--------------------
- || | |
- =====\ | |
- / Toe \==============+========|
- +-------------------------------+ <-- Heel
- | Base Slab (B) |
- +-------------------------------+ <-- Resultant R at dist x_bar
- 1. Factor of Safety Against Overturning ( FS O T \text{FS}_{OT} FS OT )
Overturning moments ( ∑ M O \sum M_O ∑ M O ) generated by horizontal lateral thrust must be resisted by stabilizing moments ( ∑ M R \sum M_R ∑ M R ) generated by vertical structural loads and soil weight above the heel slab. Moments are taken about the toe of the base slab (Point O O O ): FS O T = ∑ M R ∑ M O ≥ 2.0 \text{FS}_{OT} = \frac{\sum M_R}{\sum M_O} \ge 2.0 FS OT = ∑ M O ∑ M R ≥ 2.0
Resisting moments: ∑ M R = W 1 x 1 + W 2 x 2 + W soil x s + P a v B \sum M_R = W_1 x_1 + W_2 x_2 + W_{\text{soil}} x_s + P_{av} B ∑ M R = W 1 x 1 + W 2 x 2 + W soil x s + P a v B
Overturning moments: ∑ M O = P a h y a + P q h y q \sum M_O = P_{ah} y_a + P_{qh} y_q ∑ M O = P ah y a + P q h y q
2. Resultant Location and Eccentricity Limit ( e e e )
The distance of the base resultant force ( x ˉ \bar{x} x ˉ ) from the toe is: x ˉ = ∑ M R − ∑ M O ∑ V \bar{x} = \frac{\sum M_R - \sum M_O}{\sum V} x ˉ = ∑ V ∑ M R − ∑ M O
The eccentricity ( e e e ) of the resultant relative to the base centerline is: ≠ = B 2 − x ˉ \ne = \frac{B}{2} - \bar{x} = = 2 B − x ˉ
To prevent tensile stresses at the heel-soil interface (which causes base detachment and soil gapping), the resultant must lie within the middle third of the foundation base: ≠ ≤ B 6 \ne \le \frac{B}{6} = ≤ 6 B
3. Soil Bearing Capacity Check ( FS b e a r i n g \text{FS}_{bearing} FS b e a r in g )
When e ≤ B / 6 e \le B/6 e ≤ B /6 , the soil contact pressure distribution under the base is trapezoidal. Maximum pressure occurs at the toe ( q max q_{\text{max}} q max ) and minimum at the heel ( q min q_{\text{min}} q min ): q max, min = ∑ V B ( 1 ± 6 e B ) q_{\text{max, min}} = \frac{\sum V}{B} \left( 1 \pm \frac{6e}{B} \right) q max, min = B ∑ V ( 1 ± B 6 e )
If e > B / 6 e > B/6 e > B /6 , tensile stress is neglected and a triangular pressure distribution mobilizes over an reduced effective width B ′ = 3 x ˉ B' = 3\bar{x} B ′ = 3 x ˉ : q max = 2 ∑ V 3 x ˉ q_{\text{max}} = \frac{2 \sum V}{3 \bar{x}} q max = 3 x ˉ 2 ∑ V
The ultimate bearing capacity ( q u l t q_{ult} q u lt ) of the foundation soil is computed using Meyerhof's ultimate bearing capacity equation with eccentricity correction ( B ′ = B − 2 e B' = B - 2e B ′ = B − 2 e ). The factor of safety is: FS b e a r i n g = q u l t q max ≥ 3.0 \text{FS}_{bearing} = \frac{q_{ult}}{q_{\text{max}}} \ge 3.0 FS b e a r in g = q max q u lt ≥ 3.0
4. Factor of Safety Against Sliding ( FS s l i d i n g \text{FS}_{sliding} FS s l i d in g )
Sliding resistance is generated by base friction and cohesion along the slab-soil interface, plus any passive soil resistance in front of the toe ( P p P_p P p ): FS s l i d i n g = ∑ V tan δ b + c b ′ B ′ + P p P a h ≥ 1.5 \text{FS}_{sliding} = \frac{\sum V \tan\delta_b + c_b' B' + P_p}{P_{ah}} \ge 1.5 FS s l i d in g = P ah ∑ V tan δ b + c b ′ B ′ + P p ≥ 1.5
where δ b \delta_b δ b is the base friction angle (typically 2 3 ϕ foundation ′ \frac{2}{3}\phi_{\text{foundation}}' 3 2 ϕ foundation ′ to ϕ foundation ′ \phi_{\text{foundation}}' ϕ foundation ′ ), and c b ′ c_b' c b ′ is base adhesion. Passive resistance P p P_p P p in front of the toe is often neglected or reduced by 50 % 50\% 50% due to potential future soil erosion or disturbance.
Shear Keys: If FS s l i d i n g < 1.5 \text{FS}_{sliding} < 1.5 FS s l i d in g < 1.5 , a concrete shear key is constructed below the base slab beneath the stem or heel. The key forces the sliding failure plane deeper into the foundation soil, mobilizing full passive pressure across the key depth ( d k e y d_{key} d k ey ) and base soil friction.
AASHTO LRFD Design Methodology
Under AASHTO Load and Resistance Factor Design (LRFD) specifications, retaining structures are designed using factored loads and resistance factors: ∑ γ i Q i ≤ ϕ R n \sum \gamma_i Q_i \le \phi R_n ∑ γ i Q i ≤ ϕ R n
Critical Load Combinations (Strength I Limit State)
Vertical Earth Pressure (EV): Maximum load factor γ E V = 1.35 \gamma_{EV} = 1.35 γ E V = 1.35 (for bearing capacity/flexure); Minimum load factor γ E V = 1.00 \gamma_{EV} = 1.00 γ E V = 1.00 (for sliding/overturning stability checks where soil weight provides stabilizing resistance).
Horizontal Earth Pressure (EH): Active pressure load factor γ E H = 1.50 \gamma_{EH} = 1.50 γ E H = 1.50 .
Live Load Surcharge (LS): Load factor γ L S = 1.75 \gamma_{LS} = 1.75 γ L S = 1.75 .
- LRFD Resistance Factors ( ϕ \phi ϕ )
- Base sliding resistance on sand: ϕ τ = 0.80 \phi_{\tau} = 0.80 ϕ τ = 0.80
- Bearing resistance: ϕ b = 0.55 \phi_b = 0.55 ϕ b = 0.55
Overturning (extreme limit state / CDR evaluation): Resultant eccentricity limit e ≤ B / 4 e \le B/4 e ≤ B /4 for soil foundations, e ≤ 3 B / 8 e \le 3B/8 e ≤ 3 B /8 for rock foundations.
Internal Structural Reinforced Concrete Design
Internal structural components (stem, toe slab, heel slab) are designed as reinforced concrete cantilever beams under factored bending moments ( M u M_u M u ) and shear forces ( V u V_u V u ).
1. Stem Design
Loading: Factored horizontal active pressure ( γ E H P a h \gamma_{EH} P_{ah} γ E H P ah ) increasing triangularly with depth.
Critical Section: Base of the stem at its intersection with the base slab.
Flexural Reinforcement: Vertical tension steel on the backfill (retained) side of the stem: A s = M u ϕ f y ( d − a / 2 ) A_s = \frac{M_u}{\phi f_y (d - a/2)} A s = ϕ f y ( d − a /2 ) M u
Shear Check: Critical section for one-way shear is located at distance d d d (effective depth) above the top of the base slab. Verify ϕ V c ≥ V u \phi V_c \ge V_u ϕ V c ≥ V u .
2. Toe Slab Design
Loading: Upward net soil bearing pressure minus factored self-weight of the toe slab.
Critical Section: Front face of the stem.
Flexural Reinforcement: Horizontal main tension steel placed near the bottom of the base slab.
3. Heel Slab Design
Loading: Downward factored weight of backfill soil plus surcharge minus upward net soil bearing pressure under the heel.
Critical Section: Back face of the stem.
Flexural Reinforcement: Horizontal main tension steel placed near the top of the base slab.
Drainage Control Behind Retaining Walls
Hydrostatic water pressure buildup behind a retaining wall drastically increases horizontal thrust, reduces base friction, and is the single leading cause of wall collapse. Wall systems must incorporate positive drainage provisions:
Weep Holes: PVC drains ( 75 − 100 mm 75 - 100\text{ mm} 75 − 100 mm diameter) spaced horizontally at 1.5 − 3.0 m 1.5 - 3.0\text{ m} 1.5 − 3.0 m along the wall base.
Crushed Stone Back-Drain: A continuous layer ( 300 − 450 mm 300 - 450\text{ mm} 300 − 450 mm thick) of clean crushed stone (AASHTO No. 57) placed along the entire back-face of the wall.
Geotextile Filters: Non-woven geotextile fabric wrapped around gravel drains to prevent fine soil particle migration and piping clogging.
Prefabricated Drainage Panels: Dimpled plastic drain cores bonded to geotextile filters attached directly to the stem back-face.
- Worked Numerical Example: Cantilever Wall ASD Stability
- Problem Statement
Evaluate the external stability (sliding, overturning, eccentricity, and bearing capacity) of a cantilever retaining wall under ASD. Given parameters:
Wall height H = 5.50 m H = 5.50\text{ m} H = 5.50 m , stem thickness = 0.40 m = 0.40\text{ m} = 0.40 m , base width B = 3.20 m B = 3.20\text{ m} B = 3.20 m , base thickness D f = 0.50 m D_f = 0.50\text{ m} D f = 0.50 m , toe projection A = 0.80 m A = 0.80\text{ m} A = 0.80 m , heel projection = 2.00 m = 2.00\text{ m} = 2.00 m .
Unit weight of concrete γ c = 24.0 kN/m 3 \gamma_c = 24.0\text{ kN/m}^3 γ c = 24.0 kN/m 3 .
Backfill soil: Moist unit weight γ = 18.0 kN/m 3 \gamma = 18.0\text{ kN/m}^3 γ = 18.0 kN/m 3 , ϕ ′ = 32 ∘ \phi' = 32^\circ ϕ ′ = 3 2 ∘ , c ′ = 0 c' = 0 c ′ = 0 , horizontal ground surface, no surcharge.
Foundation soil: γ f d n = 18.5 kN/m 3 \gamma_{fdn} = 18.5\text{ kN/m}^3 γ fd n = 18.5 kN/m 3 , ϕ f d n ′ = 28 ∘ \phi_{fdn}' = 28^\circ ϕ fd n ′ = 2 8 ∘ , c f d n ′ = 0 c_{fdn}' = 0 c fd n ′ = 0 , allowable bearing capacity q a l l o w = 200 kPa q_{allow} = 200\text{ kPa} q a ll o w = 200 kPa .
Base friction angle δ b = 2 3 ϕ f d n ′ = 18.67 ∘ \delta_b = \frac{2}{3} \phi_{fdn}' = 18.67^\circ δ b = 3 2 ϕ fd n ′ = 18.6 7 ∘ . Ignore passive resistance in front of toe.
Step-by-Step Solution
1. Active Pressure Thrust ( P a P_a P a ) K a = tan 2 ( 45 ∘ − 32 ∘ / 2 ) = tan 2 ( 29 ∘ ) = 0.3073 K_a = \tan^2(45^\circ - 32^\circ/2) = \tan^2(29^\circ) = 0.3073 K a = tan 2 ( 4 5 ∘ − 3 2 ∘ /2 ) = tan 2 ( 2 9 ∘ ) = 0.3073 P a = 1 2 K a γ H 2 = 1 2 × 0.3073 × 18.0 × ( 5.50 ) 2 = 83.56 kN/m P_a = \frac{1}{2} K_a \gamma H^2 = \frac{1}{2} \times 0.3073 \times 18.0 \times (5.50)^2 = 83.56\text{ kN/m} P a = 2 1 K a γ H 2 = 2 1 × 0.3073 × 18.0 × ( 5.50 ) 2 = 83.56 kN/m P a acts horizontally at y a = H 3 = 5.50 3 = 1.833 m above the base. P_a \text{ acts horizontally at } y_a = \frac{H}{3} = \frac{5.50}{3} = 1.833\text{ m above the base.} P a acts horizontally at y a = 3 H = 3 5.50 = 1.833 m above the base.
2. Structural Weights and Resisting Moments About Toe (Point O)
Taking moments about the front tip of the toe (Point O):
Element Area/Dimensions Weight ( W i W_i W i , kN/m) Arm from Toe ( x i x_i x i , m) Resisting Moment ( M R M_R M R , kN·m/m)
W1 (Stem) 0.40 × 5.00 0.40 \times 5.00 0.40 × 5.00 0.40 × 5.00 × 24 = 48.00 0.40 \times 5.00 \times 24 = 48.00 0.40 × 5.00 × 24 = 48.00 0.80 + 0.20 = 1.00 0.80 + 0.20 = 1.00 0.80 + 0.20 = 1.00 48.00 × 1.00 = 48.00 48.00 \times 1.00 = 48.00 48.00 × 1.00 = 48.00
W2 (Base) 3.20 × 0.50 3.20 \times 0.50 3.20 × 0.50 3.20 × 0.50 × 24 = 38.40 3.20 \times 0.50 \times 24 = 38.40 3.20 × 0.50 × 24 = 38.40 3.20 / 2 = 1.60 3.20 / 2 = 1.60 3.20/2 = 1.60 38.40 × 1.60 = 61.44 38.40 \times 1.60 = 61.44 38.40 × 1.60 = 61.44
W3 (Soil over Heel) 2.00 × 5.00 2.00 \times 5.00 2.00 × 5.00 2.00 × 5.00 × 18 = 180.00 2.00 \times 5.00 \times 18 = 180.00 2.00 × 5.00 × 18 = 180.00 0.80 + 0.40 + 1.00 = 2.20 0.80 + 0.40 + 1.00 = 2.20 0.80 + 0.40 + 1.00 = 2.20 180.00 × 2.20 = 396.00 180.00 \times 2.20 = 396.00 180.00 × 2.20 = 396.00
TOTALS -- ∑ V = 266.40 kN/m \sum V = 266.40\text{ kN/m} ∑ V = 266.40 kN/m -- ∑ M R = 505.44 kN ⋅ m/m \sum M_R = 505.44\text{ kN}\cdot\text{m/m} ∑ M R = 505.44 kN ⋅ m/m
3. Overturning Moment ( ∑ M O \sum M_O ∑ M O ) ∑ M O = P a × y a = 83.56 × 1.833 = 153.16 kN ⋅ m/m \sum M_O = P_a \times y_a = 83.56 \times 1.833 = 153.16\text{ kN}\cdot\text{m/m} ∑ M O = P a × y a = 83.56 × 1.833 = 153.16 kN ⋅ m/m FS O T = ∑ M R ∑ M O = 505.44 153.16 = 3.30 ≥ 2.0 (OK for Overturning) \text{FS}_{OT} = \frac{\sum M_R}{\sum M_O} = \frac{505.44}{153.16} = 3.30 \ge 2.0 \quad \text{\textbf{(OK for Overturning)}} FS OT = ∑ M O ∑ M R = 153.16 505.44 = 3.30 ≥ 2.0 (OK for Overturning)
4. Resultant Location ( x ˉ \bar{x} x ˉ ) and Eccentricity ( e e e ) x ˉ = ∑ M R − ∑ M O ∑ V = 505.44 − 153.16 266.40 = 352.28 266.40 = 1.322 m from toe \bar{x} = \frac{\sum M_R - \sum M_O}{\sum V} = \frac{505.44 - 153.16}{266.40} = \frac{352.28}{266.40} = 1.322\text{ m from toe} x ˉ = ∑ V ∑ M R − ∑ M O = 266.40 505.44 − 153.16 = 266.40 352.28 = 1.322 m from toe ≠ = B 2 − x ˉ = 3.20 2 − 1.322 = 1.60 − 1.322 = 0.278 m \ne = \frac{B}{2} - \bar{x} = \frac{3.20}{2} - 1.322 = 1.60 - 1.322 = 0.278\text{ m} = = 2 B − x ˉ = 2 3.20 − 1.322 = 1.60 − 1.322 = 0.278 m Kern Limit: B 6 = 3.20 6 = 0.533 m \text{Kern Limit: } \frac{B}{6} = \frac{3.20}{6} = 0.533\text{ m} Kern Limit: 6 B = 6 3.20 = 0.533 m ≠ = 0.278 m ≤ 0.533 m (OK: Resultant is within Middle Third) \ne = 0.278\text{ m} \le 0.533\text{ m} \quad \text{\textbf{(OK: Resultant is within Middle Third)}} = = 0.278 m ≤ 0.533 m (OK: Resultant is within Middle Third)
5. Base Soil Bearing Pressures ( q max , q min q_{\text{max}}, q_{\text{min}} q max , q min ) q max = ∑ V B ( 1 + 6 e B ) = 266.40 3.20 ( 1 + 6 × 0.278 3.20 ) = 83.25 × ( 1 + 0.521 ) = 126.62 kPa q_{\text{max}} = \frac{\sum V}{B} \left(1 + \frac{6e}{B}\right) = \frac{266.40}{3.20} \left(1 + \frac{6 \times 0.278}{3.20}\right) = 83.25 \times (1 + 0.521) = 126.62\text{ kPa} q max = B ∑ V ( 1 + B 6 e ) = 3.20 266.40 ( 1 + 3.20 6 × 0.278 ) = 83.25 × ( 1 + 0.521 ) = 126.62 kPa q min = 83.25 × ( 1 − 0.521 ) = 39.88 kPa q_{\text{min}} = 83.25 \times (1 - 0.521) = 39.88\text{ kPa} q min = 83.25 × ( 1 − 0.521 ) = 39.88 kPa q max = 126.62 kPa ≤ q a l l o w = 200.0 kPa (OK for Bearing Capacity) q_{\text{max}} = 126.62\text{ kPa} \le q_{allow} = 200.0\text{ kPa} \quad \text{\textbf{(OK for Bearing Capacity)}} q max = 126.62 kPa ≤ q a ll o w = 200.0 kPa (OK for Bearing Capacity)
6. Factor of Safety Against Sliding ( FS s l i d i n g \text{FS}_{sliding} FS s l i d in g ) F R = ∑ V ⋅ tan δ b = 266.40 × tan ( 18.67 ∘ ) = 266.40 × 0.3379 = 90.02 kN/m F_R = \sum V \cdot \tan\delta_b = 266.40 \times \tan(18.67^\circ) = 266.40 \times 0.3379 = 90.02\text{ kN/m} F R = ∑ V ⋅ tan δ b = 266.40 × tan ( 18.6 7 ∘ ) = 266.40 × 0.3379 = 90.02 kN/m FS s l i d i n g = F R P a = 90.02 83.56 = 1.077 < 1.50 (UNSAFE for Sliding) \text{FS}_{sliding} = \frac{F_R}{P_a} = \frac{90.02}{83.56} = 1.077 < 1.50 \quad \text{\textbf{(UNSAFE for Sliding)}} FS s l i d in g = P a F R = 83.56 90.02 = 1.077 < 1.50 (UNSAFE for Sliding)
Design Recommendation: Because FS s l i d i n g = 1.08 < 1.50 \text{FS}_{sliding} = 1.08 < 1.50 FS s l i d in g = 1.08 < 1.50 , a shear key must be added below the base slab, or the base width B B B must be extended to meet sliding safety criteria.