Study guide

9.4 Consolidation Settlement & Mat/Raft Foundation Design

PE Civil Geotechnical Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Site Characterization

1.1 Site Data Interpretation & Boring Plans 1.2 In Situ Testing & Field Exploration 1.3 Soil and Rock Classification Systems 1.4 Groundwater Characterization & Hydrogeology

2 Chapter 2: Soil Mechanics, Laboratory Testing, and Analysis

2.1 Weight-Volume Phase Relationships & Index Properties 2.2 Effective Stress & Pore Water Pressure Dynamics 2.3 Shear Strength Principles & Laboratory Testing 2.4 Permeability, Hydraulic Conductivity & Seepage Properties 2.5 Consolidation & Compressibility Analysis

3 Chapter 3: Construction Observation, Monitoring, QA/QC, and Safety

3.1 Earthwork Quality Control & Compaction Verification 3.2 Geotechnical Instrumentation & Field Monitoring 3.3 Trenching, Excavation Safety & OSHA Shoring Requirements 3.4 Erosion, Scour Protection & Slope Protection During Construction

4 Chapter 4: Earthquake Engineering and Dynamic Loads

4.1 Seismic Site Characterization & Ground Motion Hazards 4.2 Soil Liquefaction Triggering & Post-Liquefaction Assessment 4.3 Dynamic Soil Properties & Ground Response Analysis 4.4 Pseudostatic Analysis & Seismic Geotechnical Design

5 Chapter 5: Earth Structures, Ground Improvement, and Pavement

5.1 Slope Stability Analysis & Limit Equilibrium Methods 5.2 Embankments, Earth Dams & Levee Geotechnics 5.3 Ground Improvement Techniques & Design 5.4 Geosynthetics in Geotechnical Engineering 5.5 Flexible & Rigid Pavement Subgrades & Buried Utilities 5.6 Landfills, Caps & Containment Systems

6 Chapter 6: Groundwater and Seepage

6.1 Dewatering System Design & Well Drawdown 6.2 Flow Nets & Two-Dimensional Seepage Analysis 6.3 Uplift Pressure, Piping & Heave Safety 6.4 Subsurface Drainage Systems & Filter Criteria

7 Chapter 7: Problematic Soil and Rock Conditions

7.1 Expansive & Collapsible Soil Engineering 7.2 Organic Soils, Sensitive Clays & Soft Marine Deposits 7.3 Corrosive, Frost-Susceptible & Degradable Formations 7.4 Karst Topography, Rock Slopes & Rockfall Hazards

8 Chapter 8: Retaining Structures

8.1 Lateral Earth Pressure Theories 8.2 Rigid Retaining Wall Design 8.3 Flexible Retaining Walls & Sheet Pile Bulkheads 8.4 Temporary Support of Excavations 8.5 Mechanically Stabilized Earth (MSE) Walls & Soil Nail Structures 8.6 Cofferdams, Underpinning & Adjacent Infrastructure Effects

9 Chapter 9: Shallow Foundations

9.1 Ultimate & Allowable Bearing Capacity Theories 9.2 Effective Footing Area, Eccentricity & Combined Footings 9.3 Induced Stress Distribution & Immediate Elastic Settlement 9.4 Consolidation Settlement & Mat/Raft Foundation Design

10 Chapter 10: Deep Foundations

10.1 Driven Pile Axial Capacity & Settlement 10.2 Drilled Shaft Axial Design & Construction Methods 10.3 Lateral Load Behavior of Deep Foundations 10.4 Pile Group Dynamics, Efficiency & Downdrag 10.5 Dynamic Load Testing & Pile Integrity Evaluation

9.4 Consolidation Settlement & Mat/Raft Foundation Design

Key Takeaways Explain This Topic AI

Primary consolidation settlement (S_c) in saturated cohesive soils results from time-dependent dissipation of excess pore water pressure under increased effective vertical stress.

Consolidation settlement calculations depend on stress history: Normally Consolidated (NC, sigma_p' = sigma_v0') versus Overconsolidated (OC, sigma_p' > sigma_v0').

For OC clays, if sigma_v0' + delta_sigma_z <= sigma_p', settlement relies on recompression index C_r; if sigma_v0' + delta_sigma_z > sigma_p', settlement transitions at sigma_p' from C_r to compression index C_c.

Mat (raft) foundations unify multiple column loads over a single large slab, reducing differential settlement and lowering bearing stress on weak or highly compressible soils.

Compensated (floating) mat foundation design excavates soil weight equal to the total structural load (q_net = 0), minimizing consolidation settlement in soft clay deposits.

Last updated: July 2026

Primary Consolidation Settlement ( S c S_c S c ​ ) Formulation

Primary consolidation settlement occurs in saturated fine-grained cohesive soils (clays and silty clays) as excess pore water pressure Δ u \Delta u Δ u induced by foundation loads dissipates, transferring load to the soil skeleton over time. 1D Consolidation e - log(sigma_v') Curve

  • Void Ratio e
  • │
  • e0 ├───────────┐ Recompression Path (Cr)
  • │ └───┐
  • ep ├───────────────┼───────────┐ Preconsolidation Pressure sigma_p'
  • │ │ └───┐ Virgin Compression Path (Cc)
  • │ │ └───┐
  • └───────────────┴───────────────────┴─────────────► log(sigma_v')
  • sigma_v0' sigma_f'
  • Stress History States and Governing Equations

Let:

  • H c = H_c = H c ​ = Thickness of compressible clay layer
  • e 0 = e_0 = e 0 ​ = Initial void ratio of clay
  • C c = C_c = C c ​ = Virgin compression index

C r = C_r = C r ​ = Recompression index ( C r ≈ 0.10 C c to 0.20 C c C_r \approx 0.10 C_c \text{ to } 0.20 C_c C r ​ ≈ 0.10 C c ​ to 0.20 C c ​ )

  • σ v 0 ′ = \sigma_{v0}' = σ v 0 ′ ​ = Initial vertical effective stress at mid-height of clay layer
  • σ p ′ = \sigma_p' = σ p ′ ​ = Preconsolidation pressure (maximum past effective vertical stress)
  • Δ σ a v g = \Delta \sigma_{avg} = Δ σ a vg ​ = Average vertical stress increment across clay layer

Weighted Average Stress Increment Calculation (Simpson's Rule): Δ σ a v g = Δ σ t o p + 4 Δ σ m i d + Δ σ b o t 6 \Delta \sigma_{avg} = \frac{\Delta \sigma_{top} + 4 \Delta \sigma_{mid} + \Delta \sigma_{bot}}{6} Δ σ a vg ​ = 6 Δ σ t o p ​ + 4Δ σ mi d ​ + Δ σ b o t ​ ​

1. Normally Consolidated Clay ( N C NC NC : σ v 0 ′ ≈ σ p ′ \sigma_{v0}' \approx \sigma_p' σ v 0 ′ ​ ≈ σ p ′ ​ ) σ f ′ = σ v 0 ′ + Δ σ a v g \sigma_f' = \sigma_{v0}' + \Delta \sigma_{avg} σ f ′ ​ = σ v 0 ′ ​ + Δ σ a vg ​ S c = C c H c 1 + e 0 log ⁡ 10 ( σ v 0 ′ + Δ σ a v g σ v 0 ′ ) S_c = \frac{C_c H_c}{1 + e_0} \log_{10}\left( \frac{\sigma_{v0}' + \Delta \sigma_{avg}}{\sigma_{v0}'} \right) S c ​ = 1 + e 0 ​ C c ​ H c ​ ​ lo g 10 ​ ( σ v 0 ′ ​ σ v 0 ′ ​ + Δ σ a vg ​ ​ )

2. Overconsolidated Clay ( O C OC OC Case A: σ v 0 ′ + Δ σ a v g ≤ σ p ′ \sigma_{v0}' + \Delta \sigma_{avg} \le \sigma_p' σ v 0 ′ ​ + Δ σ a vg ​ ≤ σ p ′ ​ )

The final stress state remains entirely on the elastic recompression curve: S c = C r H c 1 + e 0 log ⁡ 10 ( σ v 0 ′ + Δ σ a v g σ v 0 ′ ) S_c = \frac{C_r H_c}{1 + e_0} \log_{10}\left( \frac{\sigma_{v0}' + \Delta \sigma_{avg}}{\sigma_{v0}'} \right) S c ​ = 1 + e 0 ​ C r ​ H c ​ ​ lo g 10 ​ ( σ v 0 ′ ​ σ v 0 ′ ​ + Δ σ a vg ​ ​ )

3. Overconsolidated Clay ( O C OC OC Case B: σ v 0 ′ + Δ σ a v g > σ p ′ \sigma_{v0}' + \Delta \sigma_{avg} > \sigma_p' σ v 0 ′ ​ + Δ σ a vg ​ > σ p ′ ​ )

The stress path traverses recompression up to σ p ′ \sigma_p' σ p ′ ​ , then transitions onto the virgin compression line: S c = C r H c 1 + e 0 log ⁡ 10 ( σ p ′ σ v 0 ′ ) + C c H c 1 + e 0 log ⁡ 10 ( σ v 0 ′ + Δ σ a v g σ p ′ ) S_c = \frac{C_r H_c}{1 + e_0} \log_{10}\left( \frac{\sigma_p'}{\sigma_{v0}'} \right) + \frac{C_c H_c}{1 + e_0} \log_{10}\left( \frac{\sigma_{v0}' + \Delta \sigma_{avg}}{\sigma_p'} \right) S c ​ = 1 + e 0 ​ C r ​ H c ​ ​ lo g 10 ​ ( σ v 0 ′ ​ σ p ′ ​ ​ ) + 1 + e 0 ​ C c ​ H c ​ ​ lo g 10 ​ ( σ p ′ ​ σ v 0 ′ ​ + Δ σ a vg ​ ​ )

Secondary Compression (Creep) Settlement ( S s S_s S s ​ )

After primary consolidation completes ( U = 100 % U = 100\% U = 100% ): S s = C α H c 1 + e p log ⁡ 10 ( t 2 t 1 ) S_s = \frac{C\alpha H_c}{1 + e_p} \log_{10}\left( \frac{t_2}{t_1} \right) S s ​ = 1 + e p ​ C α H c ​ ​ lo g 10 ​ ( t 1 ​ t 2 ​ ​ )

Where C α C_\alpha C α ​ is secondary compression index, e p e_p e p ​ is void ratio at end of primary consolidation, and t 1 , t 2 t_1, t_2 t 1 ​ , t 2 ​ represent reference times.

Mat (Raft) Foundations

A mat foundation is a continuous reinforced concrete slab supporting all columns and walls of a structure. Mat foundations are selected when:

Individual spread footings would cover more than 50 % 50\% 50% of the building footprint area.

Soil bearing capacity is low, or soil strata exhibit erratic local soft pockets.

Structural loads are extremely heavy (e.g., high-rise buildings, silos, power plants).

Differential settlement must be minimized across sensitive equipment footprints. Compensated (Floating) Mat Foundation

  • Building Load Q_total
  • ═════════╤═════════
  • │
  • ┌───────────┴───────────┐ Basement Structure
  • │ │ Excavation Depth Df
  • ──────┴───────────────────────┴────── Ground Surface
  • ░░░░░░│ │░░░░░░
  • ░░░░░░└───────────────────────┘░░░░░░ Mat Slab (Area A)
  • ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ Uplift Net Stress Delta_q_net
  • Undrained Bearing Capacity of Mat Foundations on Clay ( ϕ u = 0 \phi_u = 0 ϕ u ​ = 0 )

Skempton (1951) net ultimate bearing capacity for mats in clay: q n e t , u l t = 5.14 s u ( 1 + 0.2 B L ) ( 1 + 0.2 D f B ) q_{net,ult} = 5.14 s_u \left( 1 + 0.2 \frac{B}{L} \right) \left( 1 + 0.2 \frac{D_f}{B} \right) q n e t , u lt ​ = 5.14 s u ​ ( 1 + 0.2 L B ​ ) ( 1 + 0.2 B D f ​ ​ )

Where maximum depth factor term ( 1 + 0.2 D f B ) ≤ 1.5 \left(1 + 0.2 \frac{D_f}{B}\right) \le 1.5 ( 1 + 0.2 B D f ​ ​ ) ≤ 1.5 .

Compensated (Floating) Foundation Design Principle

A compensated foundation reduces net soil stress by excavating soil weight equal to all or part of the total structural weight. Δ q n e t = Q t o t a l A m a t − γ D f \Delta q_{net} = \frac{Q_{total}}{A_{mat}} - \gamma D_f Δ q n e t ​ = A ma t ​ Q t o t a l ​ ​ − γ D f ​

Fully Compensated (Floating) Mat ( Δ q n e t = 0 \Delta q_{net} = 0 Δ q n e t ​ = 0 ): D f = Q t o t a l γ A m a t D_f = \frac{Q_{total}}{\gamma A_{mat}} D f ​ = γ A ma t ​ Q t o t a l ​ ​ When Δ q n e t = 0 \Delta q_{net} = 0 Δ q n e t ​ = 0 , primary consolidation settlement S c S_c S c ​ in underlying soft clay layers is theoretically reduced to near zero (except for small rebound/recompression strain).

Partially Compensated Mat ( 0 < Δ q n e t < Q t o t a l A m a t 0 < \Delta q_{net} < \frac{Q_{total}}{A_{mat}} 0 < Δ q n e t ​ < A ma t ​ Q t o t a l ​ ​ ): Reduces consolidation settlement significantly compared to surface loading.

Modulus of Subgrade Reaction ( k s k_s k s ​ )

In mat structural analysis (Winkler spring models), soil support is represented by vertical springs with subgrade modulus k s = q / δ k_s = q / \delta k s ​ = q / δ (units of kN/m 3 \text{kN/m}^3 kN/m 3 or lb/in 3 \text{lb/in}^3 lb/in 3 ).

Size Scaling Equations (Terzaghi 1955)

Given test plate subgrade modulus k 1 k_1 k 1 ​ from a 0.3 m × 0.3 m 0.3\text{ m} \times 0.3\text{ m} 0.3 m × 0.3 m ( 1 ft × 1 ft 1\text{ ft} \times 1\text{ ft} 1 ft × 1 ft ) plate:

For Cohesionless Sand: k s = k 1 ( B + 0.3 2 B ) 2 (B in meters) k_s = k_1 \left( \frac{B + 0.3}{2 B} \right)^2 \quad \text{(B in meters)} k s ​ = k 1 ​ ( 2 B B + 0.3 ​ ) 2 (B in meters) k s = k 1 ( B + 1 2 B ) 2 (B in feet) k_s = k_1 \left( \frac{B + 1}{2 B} \right)^2 \quad \text{(B in feet)} k s ​ = k 1 ​ ( 2 B B + 1 ​ ) 2 (B in feet)

For Cohesive Clay: k s = k 1 ( 0.3 B ) (B in meters) k_s = k_1 \left( \frac{0.3}{B} \right) \quad \text{(B in meters)} k s ​ = k 1 ​ ( B 0.3 ​ ) (B in meters) k s = k 1 ( 1 B ) (B in feet) k_s = k_1 \left( \frac{1}{B} \right) \quad \text{(B in feet)} k s ​ = k 1 ​ ( B 1 ​ ) (B in feet)

Tolerable Settlement and Angular Distortion ( β \beta β )

Foundation design must limit differential settlement δ d i f f \delta_{diff} δ d i ff ​ between adjacent columns spaced distance L s p a n L_{span} L s p an ​ apart. Angular Distortion β = δ d i f f L s p a n \text{Angular Distortion } \beta = \frac{\delta_{diff}}{L_{span}} Angular Distortion β = L s p an ​ δ d i ff ​ ​ Angular Distortion Definition

  • Column i Column i+1
  • │ │
  • ▼ ▼
  • ┌────────┐ ┌────────┐
  • │ │ │ │
  • └────┬───┘ └───┬────┘
  • │ │
  • ──────┼─────────────────────────┼────── Original Grade
  • │ delta_i │
  • ▼ │ delta_i+1
  • ───── ▼
  • ─────
  • ◄──────── L_span ────────►
  • Angular Distortion beta = (delta_i+1 - delta_i) / L_span

Bjerrum (1963) Serviceability Damage Criteria:

Angular Distortion Threshold ( β \beta β ) Structural / Architectural Damage Limit

β > 1 / 150 \beta > 1 / 150 β > 1/150 Structural damage in frame buildings; tilting of tall structures becomes visible.

β > 1 / 250 \beta > 1 / 250 β > 1/250 Structural distress in load-bearing masonry walls.

β > 1 / 300 \beta > 1 / 300 β > 1/300 Cracking in architectural plaster finishes and brick partition walls.

β > 1 / 500 \beta > 1 / 500 β > 1/500 Safe limit for building frame structures to prevent any architectural cracking.

β > 1 / 750 \beta > 1 / 750 β > 1/750 Strict limit for machinery sensitive to differential settlement (e.g., turbogenerators).

  • Comprehensive Worked Calculation Example
  • Problem Statement

A building load Q t o t a l = 54 , 000 kN Q_{total} = 54,000\text{ kN} Q t o t a l ​ = 54 , 000 kN is supported by a mat foundation measuring 18 m × 25 m 18\text{ m} \times 25\text{ m} 18 m × 25 m embedded at D f = 3.0 m D_f = 3.0\text{ m} D f ​ = 3.0 m in sand ( γ = 18.0 kN/m 3 \gamma = 18.0\text{ kN/m}^3 γ = 18.0 kN/m 3 ). Directly beneath the sand is a 4.0 m 4.0\text{ m} 4.0 m thick clay layer ( H c = 4.0 m H_c = 4.0\text{ m} H c ​ = 4.0 m ) with its midpoint located at z = 7.0 m z = 7.0\text{ m} z = 7.0 m below the mat base.

Clay layer properties:

Initial vertical effective stress at midpoint σ v 0 ′ = 110 kPa \sigma_{v0}' = 110\text{ kPa} σ v 0 ′ ​ = 110 kPa

  • Preconsolidation pressure σ p ′ = 150 kPa \sigma_p' = 150\text{ kPa} σ p ′ ​ = 150 kPa
  • Initial void ratio e 0 = 0.85 e_0 = 0.85 e 0 ​ = 0.85
  • Compression index C c = 0.32 C_c = 0.32 C c ​ = 0.32
  • Recompression index C r = 0.04 C_r = 0.04 C r ​ = 0.04

Calculate:

The net foundation stress increment Δ q n e t \Delta q_{net} Δ q n e t ​ at mat level

The stress increment Δ σ a v g \Delta \sigma_{avg} Δ σ a vg ​ at the midpoint of the clay layer using the 2:1 method

  • The primary consolidation settlement S c S_c S c ​ of the clay layer
  • Solution Steps

Step 1: Calculate Net Applied Foundation Pressure Δ q n e t \Delta q_{net} Δ q n e t ​ A m a t = 18 × 25 = 450 m 2 A_{mat} = 18 \times 25 = 450\text{ m}^2 A ma t ​ = 18 × 25 = 450 m 2 q g r o s s = 54 , 000 450 = 120 kPa q_{gross} = \frac{54,000}{450} = 120\text{ kPa} q g ross ​ = 450 54 , 000 ​ = 120 kPa σ v 0 , e x c ′ = γ D f = 18.0 × 3.0 = 54 kPa \sigma_{v0,exc}' = \gamma D_f = 18.0 \times 3.0 = 54\text{ kPa} σ v 0 , e x c ′ ​ = γ D f ​ = 18.0 × 3.0 = 54 kPa Δ q n e t = q g r o s s − σ v 0 , e x c ′ = 120 − 54 = 66 kPa \Delta q_{net} = q_{gross} - \sigma_{v0,exc}' = 120 - 54 = 66\text{ kPa} Δ q n e t ​ = q g ross ​ − σ v 0 , e x c ′ ​ = 120 − 54 = 66 kPa

Step 2: Compute Stress Increment Δ σ a v g \Delta \sigma_{avg} Δ σ a vg ​ at Mid-Clay Depth ( z = 7.0 m z = 7.0\text{ m} z = 7.0 m )

Using 2:1 stress distribution: B z = B + z = 18 + 7.0 = 25.0 m B_z = B + z = 18 + 7.0 = 25.0\text{ m} B z ​ = B + z = 18 + 7.0 = 25.0 m L z = L + z = 25 + 7.0 = 32.0 m L_z = L + z = 25 + 7.0 = 32.0\text{ m} L z ​ = L + z = 25 + 7.0 = 32.0 m Δ σ a v g = Δ q n e t ⋅ ( B × L ) ( B + z ) ( L + z ) = 66 × 450 25.0 × 32.0 = 29 , 700 800 = 37.125 kPa \Delta \sigma_{avg} = \frac{\Delta q_{net} \cdot (B \times L)}{(B + z)(L + z)} = \frac{66 \times 450}{25.0 \times 32.0} = \frac{29,700}{800} = 37.125\text{ kPa} Δ σ a vg ​ = ( B + z ) ( L + z ) Δ q n e t ​ ⋅ ( B × L ) ​ = 25.0 × 32.0 66 × 450 ​ = 800 29 , 700 ​ = 37.125 kPa

Step 3: Evaluate Overconsolidation Stress State σ f ′ = σ v 0 ′ + Δ σ a v g = 110 + 37.125 = 147.125 kPa \sigma_{f}' = \sigma_{v0}' + \Delta \sigma_{avg} = 110 + 37.125 = 147.125\text{ kPa} σ f ′ ​ = σ v 0 ′ ​ + Δ σ a vg ​ = 110 + 37.125 = 147.125 kPa

Compare σ f ′ \sigma_f' σ f ′ ​ to preconsolidation pressure σ p ′ = 150 kPa \sigma_p' = 150\text{ kPa} σ p ′ ​ = 150 kPa : σ f ′ = 147.125 kPa ≤ σ p ′ = 150 kPa \sigma_f' = 147.125\text{ kPa} \le \sigma_p' = 150\text{ kPa} σ f ′ ​ = 147.125 kPa ≤ σ p ′ ​ = 150 kPa

Since σ f ′ ≤ σ p ′ \sigma_f' \le \sigma_p' σ f ′ ​ ≤ σ p ′ ​ , the soil remains overconsolidated ( O C OC OC Case A), deforming strictly along the recompression curve governed by C r C_r C r ​ .

Step 4: Calculate Consolidation Settlement S c S_c S c ​ S c = C r H c 1 + e 0 log ⁡ 10 ( σ v 0 ′ + Δ σ a v g σ v 0 ′ ) S_c = \frac{C_r H_c}{1 + e_0} \log_{10}\left( \frac{\sigma_{v0}' + \Delta \sigma_{avg}}{\sigma_{v0}'} \right) S c ​ = 1 + e 0 ​ C r ​ H c ​ ​ lo g 10 ​ ( σ v 0 ′ ​ σ v 0 ′ ​ + Δ σ a vg ​ ​ ) S c = 0.04 × 4.0 1 + 0.85 log ⁡ 10 ( 147.125 110 ) S_c = \frac{0.04 \times 4.0}{1 + 0.85} \log_{10}\left( \frac{147.125}{110} \right) S c ​ = 1 + 0.85 0.04 × 4.0 ​ lo g 10 ​ ( 110 147.125 ​ ) S c = ( 0.16 1.85 ) log ⁡ 10 ( 1.3375 ) = 0.086486 × 0.126297 = 0.01092 m = 10.92 mm S_c = \left( \frac{0.16}{1.85} \right) \log_{10}(1.3375) = 0.086486 \times 0.126297 = 0.01092\text{ m} = 10.92\text{ mm} S c ​ = ( 1.85 0.16 ​ ) lo g 10 ​ ( 1.3375 ) = 0.086486 × 0.126297 = 0.01092 m = 10.92 mm

Loading diagram... Primary Consolidation Settlement Formula Selection Flowchart

Loading diagram... Mat Foundation Key Design Relationships