Study guide

9.3 Induced Stress Distribution & Immediate Elastic Settlement

PE Civil Geotechnical Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Site Characterization

1.1 Site Data Interpretation & Boring Plans 1.2 In Situ Testing & Field Exploration 1.3 Soil and Rock Classification Systems 1.4 Groundwater Characterization & Hydrogeology

2 Chapter 2: Soil Mechanics, Laboratory Testing, and Analysis

2.1 Weight-Volume Phase Relationships & Index Properties 2.2 Effective Stress & Pore Water Pressure Dynamics 2.3 Shear Strength Principles & Laboratory Testing 2.4 Permeability, Hydraulic Conductivity & Seepage Properties 2.5 Consolidation & Compressibility Analysis

3 Chapter 3: Construction Observation, Monitoring, QA/QC, and Safety

3.1 Earthwork Quality Control & Compaction Verification 3.2 Geotechnical Instrumentation & Field Monitoring 3.3 Trenching, Excavation Safety & OSHA Shoring Requirements 3.4 Erosion, Scour Protection & Slope Protection During Construction

4 Chapter 4: Earthquake Engineering and Dynamic Loads

4.1 Seismic Site Characterization & Ground Motion Hazards 4.2 Soil Liquefaction Triggering & Post-Liquefaction Assessment 4.3 Dynamic Soil Properties & Ground Response Analysis 4.4 Pseudostatic Analysis & Seismic Geotechnical Design

5 Chapter 5: Earth Structures, Ground Improvement, and Pavement

5.1 Slope Stability Analysis & Limit Equilibrium Methods 5.2 Embankments, Earth Dams & Levee Geotechnics 5.3 Ground Improvement Techniques & Design 5.4 Geosynthetics in Geotechnical Engineering 5.5 Flexible & Rigid Pavement Subgrades & Buried Utilities 5.6 Landfills, Caps & Containment Systems

6 Chapter 6: Groundwater and Seepage

6.1 Dewatering System Design & Well Drawdown 6.2 Flow Nets & Two-Dimensional Seepage Analysis 6.3 Uplift Pressure, Piping & Heave Safety 6.4 Subsurface Drainage Systems & Filter Criteria

7 Chapter 7: Problematic Soil and Rock Conditions

7.1 Expansive & Collapsible Soil Engineering 7.2 Organic Soils, Sensitive Clays & Soft Marine Deposits 7.3 Corrosive, Frost-Susceptible & Degradable Formations 7.4 Karst Topography, Rock Slopes & Rockfall Hazards

8 Chapter 8: Retaining Structures

8.1 Lateral Earth Pressure Theories 8.2 Rigid Retaining Wall Design 8.3 Flexible Retaining Walls & Sheet Pile Bulkheads 8.4 Temporary Support of Excavations 8.5 Mechanically Stabilized Earth (MSE) Walls & Soil Nail Structures 8.6 Cofferdams, Underpinning & Adjacent Infrastructure Effects

9 Chapter 9: Shallow Foundations

9.1 Ultimate & Allowable Bearing Capacity Theories 9.2 Effective Footing Area, Eccentricity & Combined Footings 9.3 Induced Stress Distribution & Immediate Elastic Settlement 9.4 Consolidation Settlement & Mat/Raft Foundation Design

10 Chapter 10: Deep Foundations

10.1 Driven Pile Axial Capacity & Settlement 10.2 Drilled Shaft Axial Design & Construction Methods 10.3 Lateral Load Behavior of Deep Foundations 10.4 Pile Group Dynamics, Efficiency & Downdrag 10.5 Dynamic Load Testing & Pile Integrity Evaluation

9.3 Induced Stress Distribution & Immediate Elastic Settlement

Key Takeaways Explain This Topic AI

Vertical stress increases in soil mass under surface loads can be estimated using 2:1 simplification method, Boussinesq theory, or Newmark's influence charts.

The 2:1 distribution method assumes surface load P spreads out at a 2 vertical to 1 horizontal slope, yielding stress at depth z: delta_sigma_z = P / [(B + z)(L + z)].

Boussinesq equation models homogeneous, isotropic, linear elastic half-space stress increments; for a point load P, delta_sigma_z = (3P / 2 pi z^2) * [1 + (r/z)^2]^(-5/2).

Immediate (elastic) settlement occurs rapidly upon load application without dissipation of pore water pressure, calculated using elastic theory: S_e = q_0 * B' * [(1 - nu^2)/E_s] * I_s * I_f.

Schmertmann's strain influence factor method calculates immediate settlement in granular soils based on CPT cone tip resistance q_c or SPT N_60, incorporating peak strain influence factor I_p at depth 0.5B (strip) or B (square).

Last updated: July 2026

Stress Distribution in Subsoils Under Surface Footings

When structural loads are applied to shallow foundations, vertical stress increases ( Δ σ z \Delta \sigma_z Δ σ z ​ ) propagate downward and laterally through the underlying soil mass. Evaluating stress increments at various depths z z z is essential for determining consolidation settlement in clay layers and immediate settlement in sand layers.

  • Methods for Computing Vertical Stress Increments ( Δ σ z \Delta \sigma_z Δ σ z ​ )
  • 1. The 2:1 (Vertical-to-Horizontal) Approximation Method

An empirical, widely used PE exam simplification that assumes surface stress spreads outward along a slope of 2 vertical to 1 horizontal ( 1 H : 2 V 1H:2V 1 H : 2 V ). 2:1 Stress Spread Projection

  • q0 (Surface Pressure)
  • ┌───────────────────┐ Footing Width B
  • └─────────┬─────────┘
  • │ z/2
  • ├───► z (Depth)
  • │
  • ┌─────────┴─────────────────┐
  • │ Spread Width = (B + z) │
  • └───────────────────────────┘

Rectangular Footing ( B × L B \times L B × L carrying total force P = q 0 B L P = q_0 B L P = q 0 ​ B L ): Δ σ z = P ( B + z ) ( L + z ) = q 0 B L ( B + z ) ( L + z ) \Delta \sigma_z = \frac{P}{(B + z)(L + z)} = \frac{q_0 B L}{(B + z)(L + z)} Δ σ z ​ = ( B + z ) ( L + z ) P ​ = ( B + z ) ( L + z ) q 0 ​ B L ​

Continuous Strip Footing (Width B B B ): Δ σ z = q 0 B B + z \Delta \sigma_z = \frac{q_0 B}{B + z} Δ σ z ​ = B + z q 0 ​ B ​

Square Footing ( B × B B \times B B × B ): Δ σ z = q 0 B 2 ( B + z ) 2 \Delta \sigma_z = \frac{q_0 B^2}{(B + z)^2} Δ σ z ​ = ( B + z ) 2 q 0 ​ B 2 ​

2. Boussinesq Theory for Elastic Half-Space

Boussinesq (1885) solved stress increments in a homogeneous, isotropic, semi-infinite linear elastic medium:

Point Load P P P at Radial Distance r r r and Depth z z z : Δ σ z = 3 P 2 π z 2 [ 1 + ( r z ) 2 ] − 5 / 2 = P z 2 I B \Delta \sigma_z = \frac{3 P}{2 \pi z^2} \left[ 1 + \left(\frac{r}{z}\right)^2 \right]^{-5/2} = \frac{P}{z^2} I_B Δ σ z ​ = 2 π z 2 3 P ​ [ 1 + ( z r ​ ) 2 ] − 5/2 = z 2 P ​ I B ​

Corner of Uniformly Loaded Flexible Rectangular Area ( B × L B \times L B × L ): Δ σ z = q 0 ⋅ I m \Delta \sigma_z = q_0 \cdot I_m Δ σ z ​ = q 0 ​ ⋅ I m ​

Where I m I_m I m ​ is Boussinesq corner influence factor determined as a function of parameters m = B / z m = B/z m = B / z and n = L / z n = L/z n = L / z : I m = 1 4 π [ 2 m n m 2 + n 2 + 1 m 2 + n 2 + m 2 n 2 + 1 ( m 2 + n 2 + 2 m 2 + n 2 + 1 ) + arctan ⁡ ( 2 m n m 2 + n 2 + 1 m 2 + n 2 − m 2 n 2 + 1 ) ] I_m = \frac{1}{4\pi} \left[ \frac{2 m n \sqrt{m^2 + n^2 + 1}}{m^2 + n^2 + m^2 n^2 + 1} \left(\frac{m^2 + n^2 + 2}{m^2 + n^2 + 1}\right) + \arctan\left(\frac{2 m n \sqrt{m^2 + n^2 + 1}}{m^2 + n^2 - m^2 n^2 + 1}\right) \right] I m ​ = 4 π 1 ​ [ m 2 + n 2 + m 2 n 2 + 1 2 mn m 2 + n 2 + 1 ​ ​ ( m 2 + n 2 + 1 m 2 + n 2 + 2 ​ ) + arctan ( m 2 + n 2 − m 2 n 2 + 1 2 mn m 2 + n 2 + 1 ​ ​ ) ]

Principle of Superposition for Interior/Exterior Stress Increments:

To calculate stress beneath the center of a rectangular area ( B × L B \times L B × L ), divide the area into four identical sub-rectangles of dimensions ( B / 2 ) × ( L / 2 ) (B/2) \times (L/2) ( B /2 ) × ( L /2 ) meeting at the center: Δ σ z , c e n t e r = 4 ⋅ q 0 ⋅ I m ( m = B / 2 z , n = L / 2 z ) \Delta \sigma_{z,center} = 4 \cdot q_0 \cdot I_m \left(m = \frac{B/2}{z}, n = \frac{L/2}{z}\right) Δ σ z , ce n t er ​ = 4 ⋅ q 0 ​ ⋅ I m ​ ( m = z B /2 ​ , n = z L /2 ​ )

3. Westergaard Theory (Stratified Elastic Medium)

Westergaard (1938) assumed thin, rigid horizontal reinforcing sheets present within soil mass (preventing lateral strain, ε x = ε y = 0 \varepsilon_x = \varepsilon_y = 0 ε x ​ = ε y ​ = 0 ). Westergaard stresses are typically lower than Boussinesq values: Δ σ z , p o i n t = P π z 2 1 [ 1 + 2 ( r / z ) 2 ] 3 / 2 \Delta \sigma_{z,point} = \frac{P}{\pi z^2} \frac{1}{\left[ 1 + 2(r/z)^2 \right]^{3/2}} Δ σ z , p o in t ​ = π z 2 P ​ [ 1 + 2 ( r / z ) 2 ] 3/2 1 ​

4. Newmark's Influence Chart Method

Newmark (1942) developed circular influence charts where each grid unit represents a constant influence value (typically I c h a r t = 0.005 I_{chart} = 0.005 I c ha r t ​ = 0.005 ). The chart is scaled such that length A B AB A B equals depth z z z . Δ σ z = I c h a r t ⋅ N g r i d ⋅ q 0 \Delta \sigma_z = I_{chart} \cdot N_{grid} \cdot q_0 Δ σ z ​ = I c ha r t ​ ⋅ N g r i d ​ ⋅ q 0 ​

Where N g r i d N_{grid} N g r i d ​ is the count of grid units covered by the foundation plan view.

Immediate Elastic Settlement ( S e S_e S e ​ )

Immediate settlement occurs practically instantly upon load application in unsaturated cohesionless soils and saturated fine-grained clays without change in moisture content (undrained distortion). Flexible vs Rigid Footing Settlement Profiles

  • Flexible Footing Rigid Footing
  • Uniform Base Pressure q0 Non-Uniform Edge Pressure
  • ┌───────────────────┐ ┌───────────────────┐
  • └─────────┬─────────┘ └─────────┬─────────┘
  • ┌─────────▼─────────┐ ┌─────────▼─────────┐
  • │ │ │ │
  • └───┐ ┌───┘ └───────────────────┘
  • └───────────┘ Uniform Settlement Se
  • Dished Settlement Profile

Elasticity Equation for Flexible and Rigid Footings S e = q 0 B ′ ( 1 − ν 2 E s ) I s I f S_e = q_0 B' \left( \frac{1 - \nu^2}{E_s} \right) I_s I_f S e ​ = q 0 ​ B ′ ( E s ​ 1 − ν 2 ​ ) I s ​ I f ​

Where:

q 0 = q_0 = q 0 ​ = Net applied foundation contact pressure (kPa or psf)

B ′ = B' = B ′ = Characteristic footprint dimension:

  • For settlement at center of flexible rectangular footing: B ′ = B / 2 B' = B/2 B ′ = B /2
  • For settlement at corner of flexible rectangular footing: B ′ = B B' = B B ′ = B
  • ν = \nu = ν = Poisson's ratio of soil (0.20-0.30 for sand, 0.40-0.50 for undrained clay)
  • E s = E_s = E s ​ = Soil Young's modulus of elasticity (kPa or psf)
  • I s = I_s = I s ​ = Shape influence factor (tabulated based on L / B L/B L / B ratio)
  • I f = I_f = I f ​ = Embedment depth factor (Fox factor, I f ≤ 1.0 I_f \le 1.0 I f ​ ≤ 1.0 )

Typical values of shape factor I s I_s I s ​ (flexible center vs rigid):

  • Footing Geometry Flexible Center I s I_s I s ​ Flexible Corner I s I_s I s ​ Rigid Footing I s I_s I s ​
  • Circular 1.00 0.64 0.79
  • Square ( L / B = 1 L/B = 1 L / B = 1 ) 1.12 0.56 0.82
  • Rectangle ( L / B = 2 L/B = 2 L / B = 2 ) 1.53 0.76 1.12
  • Rectangle ( L / B = 5 L/B = 5 L / B = 5 ) 2.10 1.05 1.60
  • Continuous Strip 3.70 1.85 3.20
  • Schmertmann's Method for Immediate Settlement in Granular Soil

Schmertmann (1970, 1978) established an empirical method integrating vertical strain influence factors I z I_z I z ​ over depth intervals beneath footings based on CPT or SPT profiles. S e = C 1 C 2 ( q 0 − σ v 0 ′ ) ∑ i = 1 n I z , i E s , i Δ z i S_e = C_1 C_2 (q_0 - \sigma_{v0}') \sum_{i=1}^{n} \frac{I_{z,i}}{E_{s,i}} \Delta z_i S e ​ = C 1 ​ C 2 ​ ( q 0 ​ − σ v 0 ′ ​ ) i = 1 ∑ n ​ E s , i ​ I z , i ​ ​ Δ z i ​

Where:

C 1 = 1 − 0.5 ( σ v 0 ′ q 0 − σ v 0 ′ ) ≥ 0.5 = C_1 = 1 - 0.5 \left( \frac{\sigma_{v0}'}{q_0 - \sigma_{v0}'} \right) \ge 0.5 = C 1 ​ = 1 − 0.5 ( q 0 ​ − σ v 0 ′ ​ σ v 0 ′ ​ ​ ) ≥ 0.5 = Embedment depth correction factor

C 2 = 1 + 0.2 log ⁡ 10 ( t 0.1 ) = C_2 = 1 + 0.2 \log_{10}\left(\frac{t}{0.1}\right) = C 2 ​ = 1 + 0.2 lo g 10 ​ ( 0.1 t ​ ) = Creep correction factor for time t t t in years

  • q 0 − σ v 0 ′ = q_0 - \sigma_{v0}' = q 0 ​ − σ v 0 ′ ​ = Net foundation pressure increase at base level
  • I z , i = I_{z,i} = I z , i ​ = Vertical strain influence factor at midpoint of layer i i i

E s , i = E_{s,i} = E s , i ​ = Equivalent elastic modulus of layer i i i :

E s = 2.5 q c E_s = 2.5 q_c E s ​ = 2.5 q c ​ (for square/circular footings)

E s = 3.5 q c E_s = 3.5 q_c E s ​ = 3.5 q c ​ (for continuous strip footings, L / B ≥ 10 L/B \ge 10 L / B ≥ 10 )

Strain Influence Factor I z I_z I z ​ Peak Characteristics: Schmertmann Strain Influence Factor Iz Curves

  • Depth z Iz Value
  • 0.0 ─────────┼──────► Iz_initial (0.1 for Square, 0.2 for Strip)
  • 0.5B ────────┼──────► Iz_peak (Square)
  • 1.0B ────────┼──────► Iz_peak (Strip)
  • 2.0B ────────┼──────► 0.0 (Square Limit)
  • 4.0B ────────┼──────► 0.0 (Strip Limit)

Peak Strain Influence Factor Value ( I z , p I_{z,p} I z , p ​ ): I z , p = 0.5 + 0.1 q 0 − σ v 0 ′ σ v p ′ I_{z,p} = 0.5 + 0.1 \sqrt{\frac{q_0 - \sigma_{v0}'}{\sigma_{vp}'}} I z , p ​ = 0.5 + 0.1 σ v p ′ ​ q 0 ​ − σ v 0 ′ ​ ​ ​ Where σ v p ′ \sigma_{vp}' σ v p ′ ​ is initial vertical effective stress at the depth of I z , p I_{z,p} I z , p ​ peak ( 0.5 B 0.5 B 0.5 B for square, 1.0 B 1.0 B 1.0 B for strip).

  • Comprehensive Worked Calculation Example
  • Problem Statement

A square footing measuring 3.0 m × 3.0 m 3.0\text{ m} \times 3.0\text{ m} 3.0 m × 3.0 m is founded at depth D f = 1.5 m D_f = 1.5\text{ m} D f ​ = 1.5 m and carries a uniform gross pressure q 0 = 180 kPa q_0 = 180\text{ kPa} q 0 ​ = 180 kPa . Soil unit weight is γ = 18.5 kN/m 3 \gamma = 18.5\text{ kN/m}^3 γ = 18.5 kN/m 3 . Groundwater is deep.

Calculate vertical stress increment Δ σ z \Delta \sigma_z Δ σ z ​ at depth z = 3.0 m z = 3.0\text{ m} z = 3.0 m below the center of the footing using the 2:1 method .

Calculate immediate elastic settlement S e S_e S e ​ at the center of the footing assuming a flexible footprint resting on an elastic layer ( E s = 30 MPa , ν = 0.30 E_s = 30\text{ MPa}, \nu = 0.30 E s ​ = 30 MPa , ν = 0.30 , shape factor I s = 1.12 I_s = 1.12 I s ​ = 1.12 , embedment factor I f = 0.90 I_f = 0.90 I f ​ = 0.90 ).

  • Solution Steps
  • Step 1: Compute 2:1 Stress Increment Δ σ z \Delta \sigma_z Δ σ z ​ at z = 3.0 m z = 3.0\text{ m} z = 3.0 m

Total column force P = q 0 ⋅ ( B × L ) = 180 × ( 3.0 × 3.0 ) = 1620 kN P = q_0 \cdot (B \times L) = 180 \times (3.0 \times 3.0) = 1620\text{ kN} P = q 0 ​ ⋅ ( B × L ) = 180 × ( 3.0 × 3.0 ) = 1620 kN .

At depth z = 3.0 m z = 3.0\text{ m} z = 3.0 m : B z = B + z = 3.0 + 3.0 = 6.0 m B_z = B + z = 3.0 + 3.0 = 6.0\text{ m} B z ​ = B + z = 3.0 + 3.0 = 6.0 m L z = L + z = 3.0 + 3.0 = 6.0 m L_z = L + z = 3.0 + 3.0 = 6.0\text{ m} L z ​ = L + z = 3.0 + 3.0 = 6.0 m Δ σ z = P ( B + z ) ( L + z ) = 1620 6.0 × 6.0 = 1620 36 = 45.0 kPa \Delta \sigma_z = \frac{P}{(B + z)(L + z)} = \frac{1620}{6.0 \times 6.0} = \frac{1620}{36} = 45.0\text{ kPa} Δ σ z ​ = ( B + z ) ( L + z ) P ​ = 6.0 × 6.0 1620 ​ = 36 1620 ​ = 45.0 kPa

Step 2: Compute Net Foundation Pressure q n e t q_{net} q n e t ​ σ v 0 ′ = γ D f = 18.5 × 1.5 = 27.75 kPa \sigma_{v0}' = \gamma D_f = 18.5 \times 1.5 = 27.75\text{ kPa} σ v 0 ′ ​ = γ D f ​ = 18.5 × 1.5 = 27.75 kPa q n e t = q 0 − σ v 0 ′ = 180 − 27.75 = 152.25 kPa q_{net} = q_0 - \sigma_{v0}' = 180 - 27.75 = 152.25\text{ kPa} q n e t ​ = q 0 ​ − σ v 0 ′ ​ = 180 − 27.75 = 152.25 kPa

Step 3: Compute Immediate Elastic Settlement S e S_e S e ​

For flexible center calculation, B ′ = B / 2 = 3.0 / 2 = 1.5 m B' = B / 2 = 3.0 / 2 = 1.5\text{ m} B ′ = B /2 = 3.0/2 = 1.5 m : S e = q n e t B ′ ( 1 − ν 2 E s ) I s I f S_e = q_{net} B' \left( \frac{1 - \nu^2}{E_s} \right) I_s I_f S e ​ = q n e t ​ B ′ ( E s ​ 1 − ν 2 ​ ) I s ​ I f ​ S e = 152.25 × 1.5 × ( 1 − 0.30 2 30 , 000 ) × 1.12 × 0.90 S_e = 152.25 \times 1.5 \times \left( \frac{1 - 0.30^2}{30,000} \right) \times 1.12 \times 0.90 S e ​ = 152.25 × 1.5 × ( 30 , 000 1 − 0.3 0 2 ​ ) × 1.12 × 0.90 S e = 228.375 × ( 0.91 30 , 000 ) × 1.008 S_e = 228.375 \times \left( \frac{0.91}{30,000} \right) \times 1.008 S e ​ = 228.375 × ( 30 , 000 0.91 ​ ) × 1.008 S e = 228.375 × 0.000030333 × 1.008 = 0.006983 m = 6.98 mm S_e = 228.375 \times 0.000030333 \times 1.008 = 0.006983\text{ m} = 6.98\text{ mm} S e ​ = 228.375 × 0.000030333 × 1.008 = 0.006983 m = 6.98 mm

Loading diagram... Subsoil Stress Increment Calculation Options

Loading diagram... Immediate Settlement Estimation Approaches