Study guide
10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
Key Takeaways Explain This Topic AI
Coil face area equals airflow divided by face velocity, and face velocity is normally held at 400 to 550 fpm because moisture carryover from a wet cooling coil begins near 550 fpm without eliminators.
Total coil capacity uses the enthalpy difference as 4.5 x cfm x delta-h, sensible capacity uses 1.08 x cfm x delta-T, and the water side uses 500 x gpm x delta-T; all three describe the same coil and must agree.
Adding rows increases capacity with diminishing returns and rising air pressure drop, because each successive row sees a smaller temperature difference between the air and the coil surface.
Coil water velocity is normally kept between 2 and 8 ft/s: below 2 ft/s the flow risks laminar behavior and poor heat transfer, and above 8 ft/s erosion and noise become problems.
A 100% outdoor air coil must be freeze-protected by a low-limit thermostat whose averaging element covers at least 1 linear foot per square foot of coil face area, plus preheat, glycol, or face-and-bypass arrangement.
Last updated: August 2026
10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
Cooling and Heating Coils is its own NCEES sub-topic (3F), separate from the condensers and evaporators of 3D. Section 3.5 established the psychrometric behavior of a coil through the apparatus dew point and bypass factor. This section is about specifying the physical device: how large its face is, how deep it is, how the water is routed through it, and how it is kept from freezing.
1. The Three Capacity Equations Must Agree
A coil selection is not finished until the air side and the water side reconcile.
- Quantity Equation (sea level, standard air) Where the constant comes from
- Total Q_total = 4.5 x cfm x (h_entering - h_leaving) 60 min/hr x 0.075 lbm/ft3
- Sensible Q_sensible = 1.08 x cfm x (T_entering - T_leaving) 60 x 0.075 x 0.24 Btu/lbm-F
- Latent Q_latent = 4,840 x cfm x (W_entering - W_leaving) 60 x 0.075 x 1,076 Btu/lbm
- Water side Q = 500 x gpm x (T_leaving - T_entering) 60 min/hr x 8.33 lb/gal x 1 Btu/lb-F
All four constants are density constants. At 5,000 ft they scale by roughly 0.83 on the air side; the water-side 500 does not change.
Worked Example - Complete Coil Selection
Select a chilled water cooling coil for 12,000 cfm entering at 80 F dry-bulb / 67 F wet-bulb (h = 31.4 Btu/lb) and leaving at 55 F dry-bulb / 54 F wet-bulb (h = 22.6 Btu/lb), using 44 F entering water with a 12 F water temperature rise .
Total capacity:
4.5 x 12,000 x (31.4 - 22.6) = 4.5 x 12,000 x 8.8 = 475,200 Btu/hr = 39.6 tons
Sensible capacity:
1.08 x 12,000 x (80 - 55) = 324,000 Btu/hr
Latent capacity and sensible heat ratio:
- Latent = 475,200 - 324,000 = 151,200 Btu/hr
- SHR = 324,000 / 475,200 = 0.68
Required water flow:
gpm = 475,200 / (500 x 12) = 79.2 gpm
Face area at a 500 fpm face velocity:
A = 12,000 / 500 = 24 ft2 , for example a coil 6 ft wide by 4 ft high
Cross-check the latent term independently: with entering W of about 0.0112 and leaving W of about 0.0086, 4,840 x 12,000 x 0.0026 gives 151,000 Btu/hr. The two agree, which confirms the chart readings are consistent.
2. Face Velocity: The Governing Selection Parameter A f a c e = Q V f a c e A_{face} = \frac{Q}{V_{face}} A f a ce = V f a ce Q
- Face Velocity Consequence
- Below 350 fpm Very large, expensive coil; poor air distribution across the face; risk of laminar bypass
- 400 to 550 fpm Standard design band for chilled water cooling coils
- Above 550 fpm Condensate carryover off a wet coil into the downstream duct; requires moisture eliminators
- 600 to 800 fpm Acceptable for dry heating coils only, where there is no condensate to entrain
Carryover is the hard limit, and it is a wet-coil phenomenon. A heating coil, or a cooling coil operating dry above the dew point, can be pushed considerably faster. Air-side pressure drop grows roughly with the square of face velocity, so the fan energy penalty compounds quickly.
3. Rows, Fins, and Diminishing Returns
Rows are the number of tube banks in the direction of airflow; fin spacing is typically 8 to 14 fins per inch.
Each additional row sees air that has already been cooled, so the driving temperature difference between the air and the coil surface is smaller and the row contributes less capacity than the one before it. Meanwhile every row adds essentially the same air pressure drop. The practical result:
- Rows Typical Application Behavior
- 1 to 2 Heating coils, preheat, reheat Low pressure drop, high leaving temperature approach
- 4 to 6 Standard comfort cooling coils Best balance of capacity, pressure drop, and cost
8 to 12 Dehumidification-driven selections, 100% outdoor air units Deep drying; large pressure drop; approaches but never reaches the apparatus dew point
Tighter fin spacing raises capacity per unit of face area but also raises pressure drop, worsens fouling, and makes cleaning harder - which is why hospital and laboratory coils are often specified at 8 to 10 fpi rather than 14.
4. Circuiting and Water-Side Hydraulics
Circuiting determines how many parallel water paths run through the coil, and it is how the designer reconciles two competing requirements: enough water velocity for good heat transfer, and not so much pressure drop that pumping becomes expensive.
- Circuiting Effect
- Full circuit Standard; moderate velocity and pressure drop
- Half circuit Fewer parallel paths, higher velocity - used for low flow or high delta-T selections
- Double circuit More parallel paths, lower velocity and pressure drop - used for high flow or glycol
Design water velocity is normally held to 2 to 8 ft/s :
Below 2 ft/s the Reynolds number can fall toward the laminar range, collapsing the tube-side heat transfer coefficient. The coil then fails to make capacity even though the flow rate looks correct on paper.
Above 8 ft/s erosion of the copper tube wall and flow noise become the limits.
Coils are always piped counterflow - water enters at the air-leaving face - so the coldest water meets the coldest air. Reversing the connections can cost 15% or more of capacity, and it is a classic commissioning finding.
5. Freeze Protection on Outdoor Air Coils
Any coil that can see outdoor air below 32 F is a freeze risk, and a burst coil floods a mechanical room. The protections are layered:
Low-limit ("freezestat") thermostat. A capillary averaging element senses the lowest temperature anywhere along its length, so a small cold stratification stripe trips it. The element must be long enough to cover the face: the standard rule is at least 1 linear foot of element per square foot of coil face area , serpentined across the face. For the 24 ft2 coil above, that is at least 24 ft of element.
Preheat coil upstream, holding mixed air above roughly 40 F before it reaches the chilled water coil.
Face-and-bypass dampers , which modulate airflow across the coil while keeping full flow through the tubes - historically the most robust arrangement for 100% outdoor air, because the coil never sees reduced water flow.
Glycol , typically 30% propylene glycol for burst protection, at the cost of about 15% reduced heat transfer and higher pumping power that must be included in the selection.
Constant full water flow with valve control on the coil bypass rather than throttling flow through the coil, since a throttled coil in cold air freezes fastest.
Steam preheat coils in outdoor air service must additionally use non-freeze (steam distributing) tube construction , be pitched to drain, be trapped with a properly sized float and thermostatic trap, and never be throttled by a modulating steam valve - throttling causes the condensate to stall and freeze inside the tube.