Study guide

10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction

PE Mechanical: HVAC and Refrigeration Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations

1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)

2 Chapter 2: Thermodynamics & Energy Balances

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment

3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment

3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes

4 Chapter 4: Heat Transfer Principles & Sizing

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)

5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals

5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves

6 Chapter 6: Heating & Cooling Load Calculations

6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis

7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design

8 Chapter 8: Refrigerants, Environmental Regulations & Safety

8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers

9 Chapter 9: HVAC Equipment & Primary Machinery

9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems

10 Chapter 10: Air-Side Systems & Distribution

10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection

11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant

11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems

12 Chapter 12: HVAC Control Concepts, Sensors & Sequences

12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences

13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes

13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops

14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations

14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)

10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction

Key Takeaways Explain This Topic AI

Total Pressure in duct systems is the algebraic sum of Static Pressure and Velocity Pressure ( P t = P s + P v P_t = P_s + P_v P t ​ = P s ​ + P v ​ ), where Velocity Pressure is calculated for standard air as P v = ( V 4005 ) 2 P_v = \left(\frac{V}{4005}\right)^2 P v ​ = ( 4005 V ​ ) 2 .

The Equal Friction duct design method sizes all duct sections for a constant frictional resistance per unit length (typically 0.08 0.08 0.08 to 0.15 in. wg / 100 ft 0.15\text{ in. wg}/100\text{ ft} 0.15 in. wg /100 ft ), causing duct velocities to naturally decrease downstream as flow rate drops.

The Static Regain duct design method sizes downstream duct transitions such that static pressure recovery from velocity reduction ( Δ P s r = R ( P v 1 − P v 2 ) \Delta P_{sr} = R(P_{v1} - P_{v2}) Δ P sr ​ = R ( P v 1 ​ − P v 2 ​ ) ) balances downstream friction and fitting losses, yielding equal static pressure at all branch takeoffs.

Huebscher's circular equivalent diameter formula converts rectangular duct dimensions ( a , b ) (a, b) ( a , b ) to an equivalent round duct diameter ( D e D_e D e ​ ) that exhibits identical airflow and frictional pressure gradient: D e = 1.30 ( a ⋅ b ) 0.625 ( a + b ) 0.250 D_e = \frac{1.30 (a \cdot b)^{0.625}}{(a + b)^{0.250}} D e ​ = ( a + b ) 0.250 1.30 ( a ⋅ b ) 0.625 ​ .

Rectangular duct aspect ratio ( AR = a / b \text{AR} = a/b AR = a / b ) should be maintained below 3 : 1 3:1 3 : 1 (maximum 4 : 1 4:1 4 : 1 ) to minimize sheet metal weight, heat gain/loss surface area, and acoustic breakout.

Last updated: August 2026

10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction

Duct design is the process of sizing air distribution ductwork, selecting routing geometries, and sizing terminal runouts to deliver design airflows to all building zones while balancing initial sheet metal fabrication cost, fan operating energy, space plenum constraints, and acoustic noise generation. On the PE Mechanical: HVAC and Refrigeration exam, duct design questions test pressure classifications, velocity pressure calculations, equivalent round duct conversions, Darcy-Weisbach friction factors, static regain derivations, and index run pressure summation.

1. Governing Fluid Mechanics in Air Distribution Systems

Airflow through closed conduits follows the steady-state conservation of mass and the extended Bernoulli energy equation. Total Pressure ( P t P_t P t ​ ), Static Pressure ( P s P_s P s ​ ), and Velocity Pressure ( P v P_v P v ​ ) are related by: P t = P s + P v P_t = P_s + P_v P t ​ = P s ​ + P v ​ TOTAL PRESSURE (Pt) = STATIC PRESSURE (Ps) + VELOCITY PRESSURE (Pv)

  • +-------------------------------------------------------------------+
  • | |
  • | Ps: Potential energy exerted equally in all directions on walls. |
  • | Measured perpendicular to airflow direction. |
  • | |
  • | Pv: Kinetic energy directed parallel to fluid streamlines. |
  • | Always POSITIVE in the direction of flow. |
  • | |
  • +-------------------------------------------------------------------+
  • Velocity Pressure Equation (Standard Air)

Velocity pressure represents fluid kinetic energy per unit volume. For standard air density ( ρ 0 = 0.075 lbm/ft 3 \rho_0 = 0.075\text{ lbm/ft}^3 ρ 0 ​ = 0.075 lbm/ft 3 at 70 ∘ F 70^\circ\text{F} 7 0 ∘ F and 29.921 in. Hg 29.921\text{ in. Hg} 29.921 in. Hg ): P v = ρ V 2 2 g c = 0.075 lbm/ft 3 × ( V ft/min / 60 ) 2 2 × 32.174 ft ⋅ lbm / ( lbf ⋅ s 2 ) × 5.197 lbf/ft 2 per in. wg P_v = \frac{\rho V^2}{2 g_c} = \frac{0.075\text{ lbm/ft}^3 \times (V\text{ ft/min} / 60)^2}{2 \times 32.174\text{ ft}\cdot\text{lbm}/(\text{lbf}\cdot\text{s}^2) \times 5.197\text{ lbf/ft}^2\text{ per in. wg}} P v ​ = 2 g c ​ ρ V 2 ​ = 2 × 32.174 ft ⋅ lbm / ( lbf ⋅ s 2 ) × 5.197 lbf/ft 2 per in. wg 0.075 lbm/ft 3 × ( V ft/min /60 ) 2 ​ P v (in. wg) = ( V 4 , 005 ) 2 ⟺ V (FPM) = 4 , 005 P v (in. wg) P_v\text{ (in. wg)} = \left(\frac{V}{4,005}\right)^2 \iff V\text{ (FPM)} = 4,005 \sqrt{P_v\text{ (in. wg)}} P v ​ (in. wg) = ( 4 , 005 V ​ ) 2 ⟺ V (FPM) = 4 , 005 P v ​ (in. wg) ​

Where:

  • V = CFM A V = \frac{\text{CFM}}{A} V = A CFM ​ = Mean air velocity in feet per minute ( FPM \text{FPM} FPM )
  • A A A = Internal cross-sectional area of duct in square feet ( ft 2 \text{ft}^2 ft 2 )

For non-standard air density ( ρ ≠ 0.075 lbm/ft 3 \rho \ne 0.075\text{ lbm/ft}^3 ρ  = 0.075 lbm/ft 3 ): P v = ( V 4 , 005 ) 2 × ( ρ 0.075 ) P_v = \left(\frac{V}{4,005}\right)^2 \times \left(\frac{\rho}{0.075}\right) P v ​ = ( 4 , 005 V ​ ) 2 × ( 0.075 ρ ​ )

2. Duct Friction Loss: Darcy-Weisbach & Colebrook Relations

Frictional pressure loss across a straight duct of length L L L and hydraulic diameter D h D_h D h ​ is governed by the Darcy-Weisbach equation: Δ P f (in. wg) = f ( L D h ) P v = f ( L D h ) ( V 4 , 005 ) 2 \Delta P_f\text{ (in. wg)} = f \left(\frac{L}{D_h}\right) P_v = f \left(\frac{L}{D_h}\right) \left(\frac{V}{4,005}\right)^2 Δ P f ​ (in. wg) = f ( D h ​ L ​ ) P v ​ = f ( D h ​ L ​ ) ( 4 , 005 V ​ ) 2

Where:

f f f = Darcy friction factor (dimensionless)

D h = 4 A P w D_h = \frac{4 A}{P_w} D h ​ = P w ​ 4 A ​ = Hydraulic diameter (where P w P_w P w ​ is wetted perimeter)

For circular duct: D h = D D_h = D D h ​ = D

For rectangular duct ( a × b a \times b a × b ): D h = 4 ( a ⋅ b ) 2 ( a + b ) = 2 a b a + b D_h = \frac{4(a \cdot b)}{2(a + b)} = \frac{2 a b}{a + b} D h ​ = 2 ( a + b ) 4 ( a ⋅ b ) ​ = a + b 2 ab ​

Colebrook-White Equation for Air Ducts

For turbulent flow in commercial galvanized sheet metal ducts (roughness ε ≈ 0.0003 ft = 0.09 mm \varepsilon \approx 0.0003\text{ ft} = 0.09\text{ mm} ε ≈ 0.0003 ft = 0.09 mm ): 1 f = − 2 log ⁡ 10 ( ε / D h 3.7 + 2.51 Re f ) \frac{1}{\sqrt{f}} = -2 \log_{10}\left(\frac{\varepsilon / D_h}{3.7} + \frac{2.51}{\text{Re} \sqrt{f}}\right) f ​ 1 ​ = − 2 lo g 10 ​ ( 3.7 ε / D h ​ ​ + Re f ​ 2.51 ​ ) Reynolds Number: Re = V ⋅ D h ν = V (FPM) × D h (ft) 60 × 1.60 × 10 − 4 ft 2 / s = 104.2 × V (FPM) × D h (ft) \text{Reynolds Number: } \text{Re} = \frac{V \cdot D_h}{\nu} = \frac{V\text{ (FPM)} \times D_h\text{ (ft)}}{60 \times 1.60 \times 10^{-4}\text{ ft}^2/\text{s}} = 104.2 \times V\text{ (FPM)} \times D_h\text{ (ft)} Reynolds Number: Re = ν V ⋅ D h ​ ​ = 60 × 1.60 × 1 0 − 4 ft 2 / s V (FPM) × D h ​ (ft) ​ = 104.2 × V (FPM) × D h ​ (ft)

3. Equivalent Circular Diameter for Rectangular Ducts (Huebscher Formula)

Rectangular ducts experience higher boundary-layer friction than round ducts of equal cross-sectional area due to corner eddy vortices and higher perimeter-to-area ratios. Huebscher's equivalent diameter formula calculates the round duct diameter ( D e D_e D e ​ ) that provides the exact same volumetric flow rate ( CFM \text{CFM} CFM ) and frictional pressure gradient ( Δ P / 100 ft \Delta P / 100\text{ ft} Δ P /100 ft ) as a rectangular duct of dimensions a × b a \times b a × b : D e = 1.30 ( a ⋅ b ) 0.625 ( a + b ) 0.250 = 1.30 [ ( a ⋅ b ) 5 ( a + b ) 2 ] 0.125 D_e = \frac{1.30 (a \cdot b)^{0.625}}{(a + b)^{0.250}} = 1.30 \left[\frac{(a \cdot b)^5}{(a + b)^2}\right]^{0.125} D e ​ = ( a + b ) 0.250 1.30 ( a ⋅ b ) 0.625 ​ = 1.30 [ ( a + b ) 2 ( a ⋅ b ) 5 ​ ] 0.125 RECTANGULAR DUCT (a x b) EQUIVALENT ROUND DUCT (De)

  • +-----------------------+ /-----------------\
  • | | b (Height) | |
  • | | | De (Dia) | (Same CFM & Same Friction)
  • +-----------------------+ \-----------------/
  • a (Width)

Important Note on Area: The equivalent round duct area ( A round = π 4 D e 2 A_{\text{round}} = \frac{\pi}{4} D_e^2 A round ​ = 4 π ​ D e 2 ​ ) is smaller than the rectangular duct area ( A rect = a ⋅ b A_{\text{rect}} = a \cdot b A rect ​ = a ⋅ b ). Consequently, the actual air velocity in the rectangular duct is lower than the velocity in the equivalent round duct: V rect = CFM a ⋅ b / 144 < V round = CFM π 4 D e 2 / 144 V_{\text{rect}} = \frac{\text{CFM}}{a \cdot b / 144} < V_{\text{round}} = \frac{\text{CFM}}{\frac{\pi}{4} D_e^2 / 144} V rect ​ = a ⋅ b /144 CFM ​ < V round ​ = 4 π ​ D e 2 ​ /144 CFM ​

Duct Aspect Ratio ( AR \text{AR} AR ) Aspect Ratio: AR = Longer Side ( a ) Shorter Side ( b ) \text{Aspect Ratio: } \text{AR} = \frac{\text{Longer Side (}a\text{)}}{\text{Shorter Side (}b\text{)}} Aspect Ratio: AR = Shorter Side ( b ) Longer Side ( a ) ​

Optimal: AR = 1.0 \text{AR} = 1.0 AR = 1.0 (Square duct): Minimizes sheet metal surface area, insulation cost, and thermal conduction losses.

Recommended Commercial Maximum: AR ≤ 3 : 1 \text{AR} \le 3:1 AR ≤ 3 : 1 .

Absolute Limit: AR ≤ 4 : 1 \text{AR} \le 4:1 AR ≤ 4 : 1 . Higher aspect ratios ( ≥ 5 : 1 \ge 5:1 ≥ 5 : 1 ) dramatically increase metal gauge thickness requirements, duct oil-canning drumming noise, and installation cost.

4. Comparison of Primary Duct Design Methodologies +---------------------------------------------------------------------------------------------------------+

  • | DUCT DESIGN METHODOLOGY MATRIX |
  • +-------------------+------------------------------------+------------------------------------------------+
  • | Method | Governing Principle | Best Application & Balancing Characteristics |
  • +-------------------+------------------------------------+------------------------------------------------+
  • | **Equal** | Constant friction loss per unit | Dominant standard for low-velocity commercial |
  • | **Friction** | length (e.g., 0.10 in. wg/100 ft). | supply & return. Non-self-balancing; requires |
  • | | Velocity reduces downstream. | manual balancing dampers on shorter runs. |
  • +-------------------+------------------------------------+------------------------------------------------+
  • | **Static** | Velocity reduction after branches | High-velocity long trunk VAV systems. |
  • | **Regain** | converts Pv to Ps, balancing | Self-balancing; maintains uniform static |
  • | | downstream section friction loss. | pressure at all VAV terminal inlets. |
  • +-------------------+------------------------------------+------------------------------------------------+
  • | **Velocity** | Arbitrary step-down of velocities | Simple exhaust/intake systems; outdated for |
  • | **Reduction** | from main trunk to branch runouts. | complex distribution networks. |
  • +-------------------+------------------------------------+------------------------------------------------+
  • | **T-Method** | Life-cycle cost optimization of | Complex industrial systems balancing lifetime |
  • | | energy vs capital metal cost. | fan kW cost vs upfront sheet metal fabrication.|
  • +-------------------+------------------------------------+------------------------------------------------+
  • Detailed Breakdown of Methodologies
  • A. Equal Friction Method

Select Design Friction Rate: Based on noise criteria and energy standards, select an initial design friction rate ( Δ P 100 \Delta P_{100} Δ P 100 ​ ). Common values:

Quiet commercial offices/libraries: 0.08 0.08 0.08 to 0.10 in. wg / 100 ft 0.10\text{ in. wg} / 100\text{ ft} 0.10 in. wg /100 ft

Standard commercial: 0.10 0.10 0.10 to 0.15 in. wg / 100 ft 0.15\text{ in. wg} / 100\text{ ft} 0.15 in. wg /100 ft

Industrial / mechanical rooms: 0.20 0.20 0.20 to 0.30 in. wg / 100 ft 0.30\text{ in. wg} / 100\text{ ft} 0.30 in. wg /100 ft

Check Maximum Velocity: Sizing the initial fan discharge trunk using equal friction may yield excessive velocity. If the resulting velocity exceeds recommended acoustic limits ( 1 , 500 1,500 1 , 500 to 1 , 800 FPM 1,800\text{ FPM} 1 , 800 FPM for commercial mains), size the first section for maximum allowable velocity, then size subsequent sections by equal friction.

Size Downstream Sections: Using the constant Δ P 100 \Delta P_{100} Δ P 100 ​ , determine diameter D e D_e D e ​ and rectangular dimensions for each section as airflow drops at branch takeoffs.

Identify Index Run (Critical Path): The duct run with the highest cumulative total pressure loss from fan discharge to the most hydraulically remote terminal unit establishes the required Fan Static Pressure (FSP).

B. Static Regain Method

As air leaves a branch takeoff, the downstream trunk carries reduced airflow. If the downstream duct is sized such that air velocity decreases ( V 2 < V 1 V_2 < V_1 V 2 ​ < V 1 ​ ), velocity pressure decreases ( P v 2 < P v 1 P_{v2} < P_{v1} P v 2 ​ < P v 1 ​ ). By the Bernoulli theorem, a fraction ( R R R ) of this kinetic energy converts back into static pressure: Static Regain: Δ P s r = R ⋅ ( P v 1 − P v 2 ) = R [ ( V 1 4 , 005 ) 2 − ( V 2 4 , 005 ) 2 ] \text{Static Regain: } \Delta P_{sr} = R \cdot (P_{v1} - P_{v2}) = R \left[\left(\frac{V_1}{4,005}\right)^2 - \left(\frac{V_2}{4,005}\right)^2\right] Static Regain: Δ P sr ​ = R ⋅ ( P v 1 ​ − P v 2 ​ ) = R [ ( 4 , 005 V 1 ​ ​ ) 2 − ( 4 , 005 V 2 ​ ​ ) 2 ]

Where R R R is the Static Regain Recovery Factor (typically 0.75 0.75 0.75 for standard commercial duct transitions with included expansion angles ≤ 15 ∘ \le 15^\circ ≤ 1 5 ∘ ). STATIC REGAIN MECHANISM ACROSS TRUNK TRANSITION:

  • Section 1 (High V1, High Pv1) Section 2 (Lower V2, Lower Pv2)
  • ------------------------\ -------------------------------
  • Airflow: Q1 = 5,000 CFM \ Transition Airflow: Q2 = 3,000 CFM
  • Velocity: V1 = 1,800 FPM \ (R=0.75) Velocity: V2 = 1,200 FPM
  • ---------------------------\ -------------------------------
  • \---------
  • Total Pressure: Pt1 =======================> Drops due to fitting loss (Pt2 < Pt1)
  • Velocity Pressure: Pv1 =======================> Drops (Pv2 < Pv1)
  • Static Pressure: Ps1 ====[ Ps Regain ]======> Rises! (Ps2 = Ps1 + Delta_Psr - Delta_P_loss)

In ideal static regain design, the static regain is sized to exactly offset the downstream duct friction and fitting losses: Δ P s r = Δ P f , 2 + Δ P fitting , 2 \Delta P_{sr} = \Delta P_{f,2} + \Delta P_{\text{fitting},2} Δ P sr ​ = Δ P f , 2 ​ + Δ P fitting , 2 ​

This produces identical static pressure at every terminal box takeoff along the main trunk, eliminating duct static imbalance.

5. Maximum Design Air Velocities & Noise Criteria (NC)

High duct velocity causes turbulent vortex shedding, casing vibration, and aerodynamic noise that radiates through ceiling plenums or breaks into occupied spaces.

  • System Component / Zone Maximum Design Velocity (FPM) Typical NC Rating Range
  • Main Supply Trunk (Mechanical Room) 1,800 to 2,500 FPM NC 45 to 55
  • Main Supply Trunk (Above Occupied Spaces) 1,200 to 1,500 FPM NC 30 to 40
  • Branch Ducts to VAV Boxes 1,000 to 1,200 FPM NC 30 to 35
  • Branch Runouts to Diffusers 600 to 800 FPM NC 25 to 30
  • Diffuser Neck / Grille Face 400 to 600 FPM NC 20 to 30
  • Main Return Air Ducts 1,000 to 1,400 FPM NC 35 to 45
  • Louvers / Outside Air Intakes 400 to 600 FPM (Prevents rain ingestion) N/A
  • 6. Worked Example: Equal Friction Sizing & Index Run Pressure Loss

Problem: A commercial rooftop air handling unit supplies 4 , 500 CFM 4,500\text{ CFM} 4 , 500 CFM of standard air through a supply duct system designed using the Equal Friction method at a rate of Δ P 100 = 0.10 in. wg / 100 ft \Delta P_{100} = 0.10\text{ in. wg} / 100\text{ ft} Δ P 100 ​ = 0.10 in. wg /100 ft . The index run consists of three sequential duct sections:

Section 1: Carries 4 , 500 CFM 4,500\text{ CFM} 4 , 500 CFM over a straight length of 60 ft 60\text{ ft} 60 ft . Due to ceiling plenum depth, maximum rectangular duct height is restricted to b = 14 in. b = 14\text{ in.} b = 14 in.

Section 2: After a takeoff of 1 , 500 CFM 1,500\text{ CFM} 1 , 500 CFM , carries 3 , 000 CFM 3,000\text{ CFM} 3 , 000 CFM over a straight length of 40 ft 40\text{ ft} 40 ft . Maximum duct height is b = 12 in. b = 12\text{ in.} b = 12 in.

Section 3: After another takeoff of 1 , 500 CFM 1,500\text{ CFM} 1 , 500 CFM , carries 1 , 500 CFM 1,500\text{ CFM} 1 , 500 CFM over a straight length of 50 ft 50\text{ ft} 50 ft with a round spiral duct.

Fittings along Index Run: Section 1 includes a fan discharge transition ( C o = 0.15 C_o = 0.15 C o ​ = 0.15 ) and one 90 ∘ 90^\circ 9 0 ∘ radius elbow ( C o = 0.20 C_o = 0.20 C o ​ = 0.20 ). Section 2 includes one 45 ∘ 45^\circ 4 5 ∘ elbow ( C o = 0.12 C_o = 0.12 C o ​ = 0.12 ). Section 3 terminates in a VAV terminal box requiring 0.50 in. wg 0.50\text{ in. wg} 0.50 in. wg minimum inlet static pressure, a flexible duct runout ( 10 ft 10\text{ ft} 10 ft at 0.05 in. wg 0.05\text{ in. wg} 0.05 in. wg ), and a ceiling diffuser ( 0.08 in. wg 0.08\text{ in. wg} 0.08 in. wg drop).

Find:

Sizing for Section 1: Equivalent diameter D e D_e D e ​ , required width a a a , actual rectangular area A A A , actual duct velocity V 1 V_1 V 1 ​ , and velocity pressure P v 1 P_{v1} P v 1 ​ .

Sizing for Section 2: Equivalent diameter D e D_e D e ​ , required width a a a , actual velocity V 2 V_2 V 2 ​ , and velocity pressure P v 2 P_{v2} P v 2 ​ .

Sizing for Section 3: Round duct diameter D 3 D_3 D 3 ​ , velocity V 3 V_3 V 3 ​ , and velocity pressure P v 3 P_{v3} P v 3 ​ .

Total static pressure loss along the index run and required fan static pressure (FSP).

(Friction Chart lookup values at Δ P 100 = 0.10 in. wg / 100 ft \Delta P_{100} = 0.10\text{ in. wg}/100\text{ ft} Δ P 100 ​ = 0.10 in. wg /100 ft : 4 , 500 CFM → D e = 21.6 in. 4,500\text{ CFM} \to D_e = 21.6\text{ in.} 4 , 500 CFM → D e ​ = 21.6 in. ; 3 , 000 CFM → D e = 18.5 in. 3,000\text{ CFM} \to D_e = 18.5\text{ in.} 3 , 000 CFM → D e ​ = 18.5 in. ; 1 , 500 CFM → D e = 14.2 in. 1,500\text{ CFM} \to D_e = 14.2\text{ in.} 1 , 500 CFM → D e ​ = 14.2 in. ).

Step-by-Step Solution:

Step 1: Size Section 1 ( 4 , 500 CFM 4,500\text{ CFM} 4 , 500 CFM , b = 14 in. b = 14\text{ in.} b = 14 in. , D e = 21.6 in. D_e = 21.6\text{ in.} D e ​ = 21.6 in. ). Using Huebscher formula inversion or ductulator tables for D e = 21.6 in. D_e = 21.6\text{ in.} D e ​ = 21.6 in. with b = 14 in. b = 14\text{ in.} b = 14 in. , solve for width a a a : a ≈ 30.0 in. a \approx 30.0\text{ in.} a ≈ 30.0 in.

Let's check D e D_e D e ​ for 30 in. × 14 in. 30\text{ in.} \times 14\text{ in.} 30 in. × 14 in. : D e = 1.30 ( 30 × 14 ) 0.625 ( 30 + 14 ) 0.250 = 1.30 ( 420 ) 0.625 ( 44 ) 0.250 = 1.30 ( 43.916 ) 2.576 = 57.09 2.576 = 22.16 in. ≈ 22 in. D_e = \frac{1.30 (30 \times 14)^{0.625}}{(30 + 14)^{0.250}} = \frac{1.30 (420)^{0.625}}{(44)^{0.250}} = \frac{1.30 (43.916)}{2.576} = \frac{57.09}{2.576} = 22.16\text{ in.} \approx 22\text{ in.} D e ​ = ( 30 + 14 ) 0.250 1.30 ( 30 × 14 ) 0.625 ​ = ( 44 ) 0.250 1.30 ( 420 ) 0.625 ​ = 2.576 1.30 ( 43.916 ) ​ = 2.576 57.09 ​ = 22.16 in. ≈ 22 in.

Using 30 in. × 14 in. 30\text{ in.} \times 14\text{ in.} 30 in. × 14 in. , Cross-sectional Area: A 1 = 30 × 14 144 = 420 144 = 2.917 ft 2 A_1 = \frac{30 \times 14}{144} = \frac{420}{144} = 2.917\text{ ft}^2 A 1 ​ = 144 30 × 14 ​ = 144 420 ​ = 2.917 ft 2 V 1 = 4 , 500 CFM 2.917 ft 2 = 1 , 543 FPM V_1 = \frac{4,500\text{ CFM}}{2.917\text{ ft}^2} = 1,543\text{ FPM} V 1 ​ = 2.917 ft 2 4 , 500 CFM ​ = 1 , 543 FPM P v 1 = ( 1 , 543 4 , 005 ) 2 = ( 0.3853 ) 2 = 0.1485 in. wg P_{v1} = \left(\frac{1,543}{4,005}\right)^2 = (0.3853)^2 = 0.1485\text{ in. wg} P v 1 ​ = ( 4 , 005 1 , 543 ​ ) 2 = ( 0.3853 ) 2 = 0.1485 in. wg

Step 2: Size Section 2 ( 3 , 000 CFM 3,000\text{ CFM} 3 , 000 CFM , b = 12 in. b = 12\text{ in.} b = 12 in. , D e = 18.5 in. D_e = 18.5\text{ in.} D e ​ = 18.5 in. ). For D e = 18.5 in. D_e = 18.5\text{ in.} D e ​ = 18.5 in. with b = 12 in. b = 12\text{ in.} b = 12 in. , required width is a = 26.0 in. a = 26.0\text{ in.} a = 26.0 in. A 2 = 26 × 12 144 = 312 144 = 2.167 ft 2 A_2 = \frac{26 \times 12}{144} = \frac{312}{144} = 2.167\text{ ft}^2 A 2 ​ = 144 26 × 12 ​ = 144 312 ​ = 2.167 ft 2 V 2 = 3 , 000 CFM 2.167 ft 2 = 1 , 385 FPM V_2 = \frac{3,000\text{ CFM}}{2.167\text{ ft}^2} = 1,385\text{ FPM} V 2 ​ = 2.167 ft 2 3 , 000 CFM ​ = 1 , 385 FPM P v 2 = ( 1 , 385 4 , 005 ) 2 = ( 0.3458 ) 2 = 0.1196 in. wg P_{v2} = \left(\frac{1,385}{4,005}\right)^2 = (0.3458)^2 = 0.1196\text{ in. wg} P v 2 ​ = ( 4 , 005 1 , 385 ​ ) 2 = ( 0.3458 ) 2 = 0.1196 in. wg

Step 3: Size Section 3 ( 1 , 500 CFM 1,500\text{ CFM} 1 , 500 CFM , Round Duct D e = 14.2 in. D_e = 14.2\text{ in.} D e ​ = 14.2 in. ). Select standard commercial round duct: D 3 = 14.0 in. D_3 = 14.0\text{ in.} D 3 ​ = 14.0 in. A 3 = π 4 ( 14 12 ) 2 = 0.7854 × 1.361 = 1.069 ft 2 A_3 = \frac{\pi}{4} \left(\frac{14}{12}\right)^2 = 0.7854 \times 1.361 = 1.069\text{ ft}^2 A 3 ​ = 4 π ​ ( 12 14 ​ ) 2 = 0.7854 × 1.361 = 1.069 ft 2 V 3 = 1 , 500 CFM 1.069 ft 2 = 1 , 403 FPM V_3 = \frac{1,500\text{ CFM}}{1.069\text{ ft}^2} = 1,403\text{ FPM} V 3 ​ = 1.069 ft 2 1 , 500 CFM ​ = 1 , 403 FPM P v 3 = ( 1 , 403 4 , 005 ) 2 = ( 0.3503 ) 2 = 0.1227 in. wg P_{v3} = \left(\frac{1,403}{4,005}\right)^2 = (0.3503)^2 = 0.1227\text{ in. wg} P v 3 ​ = ( 4 , 005 1 , 403 ​ ) 2 = ( 0.3503 ) 2 = 0.1227 in. wg

Step 4: Compute Total Pressure Losses along Index Run.

Frictional Losses (Straight Ducts): Δ P friction = ( 60 ft + 40 ft + 50 ft 100 ) × 0.10 in. wg = 150 100 × 0.10 = 0.150 in. wg \Delta P_{\text{friction}} = \left(\frac{60\text{ ft} + 40\text{ ft} + 50\text{ ft}}{100}\right) \times 0.10\text{ in. wg} = \frac{150}{100} \times 0.10 = 0.150\text{ in. wg} Δ P friction ​ = ( 100 60 ft + 40 ft + 50 ft ​ ) × 0.10 in. wg = 100 150 ​ × 0.10 = 0.150 in. wg

Fitting Dynamic Losses: Sec 1 Transition: Δ P = 0.15 × 0.1485 = 0.0223 in. wg \text{Sec 1 Transition: } \Delta P = 0.15 \times 0.1485 = 0.0223\text{ in. wg} Sec 1 Transition: Δ P = 0.15 × 0.1485 = 0.0223 in. wg Sec 1 90 ∘ Elbow: Δ P = 0.20 × 0.1485 = 0.0297 in. wg \text{Sec 1 } 90^\circ\text{ Elbow: } \Delta P = 0.20 \times 0.1485 = 0.0297\text{ in. wg} Sec 1 9 0 ∘ Elbow: Δ P = 0.20 × 0.1485 = 0.0297 in. wg Sec 2 45 ∘ Elbow: Δ P = 0.12 × 0.1196 = 0.0144 in. wg \text{Sec 2 } 45^\circ\text{ Elbow: } \Delta P = 0.12 \times 0.1196 = 0.0144\text{ in. wg} Sec 2 4 5 ∘ Elbow: Δ P = 0.12 × 0.1196 = 0.0144 in. wg Σ Δ P fittings = 0.0223 + 0.0297 + 0.0144 = 0.0664 in. wg \Sigma \Delta P_{\text{fittings}} = 0.0223 + 0.0297 + 0.0144 = 0.0664\text{ in. wg} ΣΔ P fittings ​ = 0.0223 + 0.0297 + 0.0144 = 0.0664 in. wg

Terminal Devices & Runout: Δ P terminals = 0.50 (VAV Box) + 0.05 (Flex) + 0.08 (Diffuser) = 0.630 in. wg \Delta P_{\text{terminals}} = 0.50\text{ (VAV Box)} + 0.05\text{ (Flex)} + 0.08\text{ (Diffuser)} = 0.630\text{ in. wg} Δ P terminals ​ = 0.50 (VAV Box) + 0.05 (Flex) + 0.08 (Diffuser) = 0.630 in. wg

Total Fan Static Pressure (FSP) Required: FSP = Δ P friction + Σ Δ P fittings + Δ P terminals = 0.150 + 0.0664 + 0.630 = 0.8464 in. wg ≈ 0.85 in. wg \text{FSP} = \Delta P_{\text{friction}} + \Sigma \Delta P_{\text{fittings}} + \Delta P_{\text{terminals}} = 0.150 + 0.0664 + 0.630 = 0.8464\text{ in. wg} \approx 0.85\text{ in. wg} FSP = Δ P friction ​ + ΣΔ P fittings ​ + Δ P terminals ​ = 0.150 + 0.0664 + 0.630 = 0.8464 in. wg ≈ 0.85 in. wg

7. NCEES Reference Handbook Navigation & Exam Tips

Huebscher Formula: Look in the Mechanical Engineering Reference Handbook under Fluid Mechanics / HVAC Duct Design for D e = 1.30 ( a b ) 0.625 ( a + b ) 0.250 D_e = \frac{1.30 (ab)^{0.625}}{(a+b)^{0.250}} D e ​ = ( a + b ) 0.250 1.30 ( ab ) 0.625 ​ .

Static Regain Equation: Remember Δ P s r = R ( P v 1 − P v 2 ) \Delta P_{sr} = R(P_{v1} - P_{v2}) Δ P sr ​ = R ( P v 1 ​ − P v 2 ​ ) . When velocity drops, static pressure increases, offsetting friction.

Velocity Pressure Constant: Commit P v = ( V / 4005 ) 2 P_v = (V / 4005)^2 P v ​ = ( V /4005 ) 2 to memory for standard air ( 0.075 lbm/ft 3 0.075\text{ lbm/ft}^3 0.075 lbm/ft 3 ).

Loading diagram... Duct Static, Velocity & Total Pressure Gradients