Study guide

10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics

PE Mechanical: HVAC and Refrigeration Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations

1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)

2 Chapter 2: Thermodynamics & Energy Balances

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment

3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment

3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes

4 Chapter 4: Heat Transfer Principles & Sizing

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)

5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals

5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves

6 Chapter 6: Heating & Cooling Load Calculations

6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis

7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design

8 Chapter 8: Refrigerants, Environmental Regulations & Safety

8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers

9 Chapter 9: HVAC Equipment & Primary Machinery

9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems

10 Chapter 10: Air-Side Systems & Distribution

10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection

11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant

11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems

12 Chapter 12: HVAC Control Concepts, Sensors & Sequences

12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences

13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes

13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops

14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations

14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)

10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics

Key Takeaways Explain This Topic AI

Centrifugal fan impellers are classified by blade geometry: Airfoil (AF, highest efficiency 85-90%, non-overloading BHP), Backward-Inclined (BI, rugged, non-overloading), Forward-Curved (FC, compact, overloading BHP curve with stall dip), and Radial (rugged material handling).

Fan Affinity Laws dictate performance scaling with speed ( N N N ) and gas density ( ρ \rho ρ ): CFM ∝ N \text{CFM} \propto N CFM ∝ N , Δ P ∝ N 2 ⋅ ρ \Delta P \propto N^2 \cdot \rho Δ P ∝ N 2 ⋅ ρ , and BHP ∝ N 3 ⋅ ρ \text{BHP} \propto N^3 \cdot \rho BHP ∝ N 3 ⋅ ρ ; CFM is independent of air density for a fixed fan speed.

Fan Total Pressure is FTP = P t 2 − P t 1 \text{FTP} = P_{t2} - P_{t1} FTP = P t 2 ​ − P t 1 ​ , and Fan Static Pressure is FSP = FTP − P v 2 = P s 2 − P t 1 \text{FSP} = \text{FTP} - P_{v2} = P_{s2} - P_{t1} FSP = FTP − P v 2 ​ = P s 2 ​ − P t 1 ​ ; Fan Brake Horsepower is BHP = CFM × FTP 6356 × η t = CFM × FSP 6356 × η s \text{BHP} = \frac{\text{CFM} \times \text{FTP}}{6356 \times \eta_t} = \frac{\text{CFM} \times \text{FSP}}{6356 \times \eta_s} BHP = 6356 × η t ​ CFM × FTP ​ = 6356 × η s ​ CFM × FSP ​ .

System Effect Factors (SEF, AMCA 201) represent additional dynamic pressure losses caused by poor inlet or discharge duct geometry (e.g. abrupt elbows at fan outlet before 100% effective duct length L e L_e L e ​ ), which degrade fan performance below factory rating curves.

Forward-curved and axial fans exhibit aerodynamic stall and surge when operated to the left of their peak pressure curve, resulting in flow separation, low-frequency rumble, and mechanical vibration.

Last updated: August 2026

10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics

Fans are the primary aerodynamic turbomachines that convert mechanical shaft power into fluid pressure head to circulate air through ductwork, coils, filters, and terminal devices. Selecting the appropriate fan architecture, understanding fan curve / system curve interactions, evaluating non-overloading power curves, calculating density altitude corrections, and mitigating AMCA System Effect Factors (SEF) are critical competencies tested on the PE Mechanical: HVAC and Refrigeration exam.

1. Aerodynamic Fan Classifications & Blade Geometries

Commercial and industrial fans are classified into Centrifugal and Axial architectures based on airflow path through the impeller: +---------------------------------------------------------------------------------------------------------+

  • | PRIMARY FAN CLASSIFICATIONS |
  • +------------------------------------+--------------------------------------------------------------------+
  • | 1. CENTRIFUGAL FANS | 2. AXIAL FANS |
  • | Air enters axially at impeller | Air enters and leaves along the same axial centerline axis. |
  • | eye, turns 90°, and discharges | Imparts kinetic energy via aerodynamic lift on rotating blades. |
  • | radially outward through blades. | High volumetric flow (CFM) at low to medium static pressure. |
  • +------------------------------------+--------------------------------------------------------------------+
  • | • Airfoil (AF) | • Propeller (Panel / Wall exhaust) |
  • | • Backward-Inclined / Curved (BI) | • Tubeaxial (Duct mounted) |
  • | • Forward-Curved (FC) | • Vaneaxial (Internal stator guide vanes, high pressure) |
  • | • Radial (R) | |
  • +------------------------------------+--------------------------------------------------------------------+
  • Detailed Engineering Comparison of Fan Types

Fan Classification Blade Profile & Rotation Total Efficiency ( η t \eta_t η t ​ ) Horsepower Curve Characteristic Common HVAC Applications

Airfoil (AF) Hollow backward-curved blades with true aerodynamic airfoil cross-section. 85 % 85\% 85% to 90 % 90\% 90% (Highest efficiency) Non-overloading: Power peaks near peak efficiency point, then flattens or drops toward free delivery. Large central AHUs, high-pressure VAV supply systems, clean air distribution.

Backward-Curved / Inclined (BC/BI) Flat or curved single-thickness backward-leaning blades. 75 % 75\% 75% to 85 % 85\% 85% Non-overloading: Motor cannot be overloaded even if system resistance is lower than designed. General HVAC supply and return, mildly contaminated or moist airstreams.

Forward-Curved (FC) Many small, shallow blades curved forward in the direction of rotation ("squirrel cage"). 60 % 60\% 60% to 70 % 70\% 70% Overloading: Brake horsepower rises continuously toward maximum flow at low static pressure! Residential furnaces, packaged terminal air conditioners (PTAC), small FCUs.

Radial Blade (R) Flat radial blades extending straight from hub. 55 % 55\% 55% to 65 % 65\% 65% Overloading: Moderate rise with flow. High mechanical strength. Industrial dust collection, pneumatic conveying, material handling exhaust.

Vaneaxial Airfoil blades in cylindrical housing with downstream stator guide vanes. 80 % 80\% 80% to 88 % 88\% 88% Overloading at Shutoff: Maximum horsepower occurs at zero flow (shutoff block)! Tunnel ventilation, naval marine systems, high-pressure industrial cleanrooms. CENTRIFUGAL BLADE PROFILES: FAN HORSEPOWER CHARACTERISTICS:

  • Airfoil (AF): Forward-Curved (FC): BHP
  • (Backward) (Forward) ^
  • | /--- FC (Overloading: Power climbs!)
  • __---===\ //===\ | /
  • ( Airfoil) || | | .-----. AF (Non-overloading: Peaks & drops)
  • -___===/ \\===/ | ( )
  • | '-----'
  • Rotation: Clockwise Rotation: Clockwise +-----------------------------> Airflow (CFM)

Safety / Reliability Note on Forward-Curved Fans: Because forward-curved fans possess an overloading horsepower characteristic, if duct static pressure is lower than designed (e.g., during construction testing with open filters or disconnect ductwork), airflow spikes dramatically and the motor will draw excessive current, causing motor overload and thermal burnout.

2. Fan Performance Pressures & Efficiency Definitions

AMCA Standard 210 defines fan pressure and power relationships: Fan Total Pressure (FTP): FTP = Pt2 (Fan Outlet) - Pt1 (Fan Inlet)

  • Fan Velocity Pressure (FVP): FVP = Pv2 (Velocity Pressure at Fan Outlet Nozzle)
  • Fan Static Pressure (FSP): FSP = FTP - FVP = Ps2 - Pt1 = Ps2 - Ps1 - Pv1

Fan Efficiencies & Brake Horsepower Total Air Power: W ˙ t , air (hp) = CFM × FTP (in. wg) 6 , 356 \text{Total Air Power: } \dot{W}_{t,\text{air}}\text{ (hp)} = \frac{\text{CFM} \times \text{FTP (in. wg)}}{6,356} Total Air Power: W ˙ t , air ​ (hp) = 6 , 356 CFM × FTP (in. wg) ​ Static Air Power: W ˙ s , air (hp) = CFM × FSP (in. wg) 6 , 356 \text{Static Air Power: } \dot{W}_{s,\text{air}}\text{ (hp)} = \frac{\text{CFM} \times \text{FSP (in. wg)}}{6,356} Static Air Power: W ˙ s , air ​ (hp) = 6 , 356 CFM × FSP (in. wg) ​ Fan Total Efficiency: η t = W ˙ t , air BHP = CFM × FTP 6 , 356 × BHP \text{Fan Total Efficiency: } \eta_t = \frac{\dot{W}_{t,\text{air}}}{\text{BHP}} = \frac{\text{CFM} \times \text{FTP}}{6,356 \times \text{BHP}} Fan Total Efficiency: η t ​ = BHP W ˙ t , air ​ ​ = 6 , 356 × BHP CFM × FTP ​ Fan Static Efficiency: η s = W ˙ s , air BHP = CFM × FSP 6 , 356 × BHP \text{Fan Static Efficiency: } \eta_s = \frac{\dot{W}_{s,\text{air}}}{\text{BHP}} = \frac{\text{CFM} \times \text{FSP}}{6,356 \times \text{BHP}} Fan Static Efficiency: η s ​ = BHP W ˙ s , air ​ ​ = 6 , 356 × BHP CFM × FSP ​ Fan Brake Horsepower: BHP = CFM × FTP 6 , 356 × η t = CFM × FSP 6 , 356 × η s \text{Fan Brake Horsepower: } \text{BHP} = \frac{\text{CFM} \times \text{FTP}}{6,356 \times \eta_t} = \frac{\text{CFM} \times \text{FSP}}{6,356 \times \eta_s} Fan Brake Horsepower: BHP = 6 , 356 × η t ​ CFM × FTP ​ = 6 , 356 × η s ​ CFM × FSP ​

3. Fan Affinity Laws (Scaling Relationships)

The Fan Affinity Laws govern fan performance scaling when rotational speed ( N N N ), gas density ( ρ \rho ρ ), or geometric impeller diameter ( D D D ) are varied.

1. Speed Variation ( N N N ) at Constant Diameter ( D D D ) & Constant Density ( ρ \rho ρ ) CFM 2 CFM 1 = N 2 N 1 \frac{\text{CFM}_2}{\text{CFM}_1} = \frac{N_2}{N_1} CFM 1 ​ CFM 2 ​ ​ = N 1 ​ N 2 ​ ​ P 2 P 1 = ( N 2 N 1 ) 2 \frac{P_2}{P_1} = \left(\frac{N_2}{N_1}\right)^2 P 1 ​ P 2 ​ ​ = ( N 1 ​ N 2 ​ ​ ) 2 BHP 2 BHP 1 = ( N 2 N 1 ) 3 \frac{\text{BHP}_2}{\text{BHP}_1} = \left(\frac{N_2}{N_1}\right)^3 BHP 1 ​ BHP 2 ​ ​ = ( N 1 ​ N 2 ​ ​ ) 3

VFD Power Law: Fan brake horsepower varies with the cube of the speed ratio ( ( N 2 N 1 ) 3 (\frac{N_2}{N_1})^3 ( N 1 ​ N 2 ​ ​ ) 3 ). Reducing fan speed by 20 % 20\% 20% ( N 2 / N 1 = 0.80 N_2/N_1 = 0.80 N 2 ​ / N 1 ​ = 0.80 ) reduces power consumption to ( 0.80 ) 3 = 0.512 (0.80)^3 = 0.512 ( 0.80 ) 3 = 0.512 —a massive 48.8 % 48.8\% 48.8% energy savings .

2. Density Variation ( ρ \rho ρ ) at Constant Speed ( N N N ) & Constant Diameter ( D D D )

When a fan operates at elevated temperature or high altitude (non-standard density ρ ≠ 0.075 lbm/ft 3 \rho \ne 0.075\text{ lbm/ft}^3 ρ  = 0.075 lbm/ft 3 ):

Volumetric Airflow is Invariant: CFM 2 = CFM 1 \text{CFM}_2 = \text{CFM}_1 CFM 2 ​ = CFM 1 ​ (A fan is a constant-volume machine; it displaces the exact same geometric volume of fluid regardless of density).

Pressure scales linearly with density: P 2 P 1 = ρ 2 ρ 1 = d r \frac{P_2}{P_1} = \frac{\rho_2}{\rho_1} = d_r P 1 ​ P 2 ​ ​ = ρ 1 ​ ρ 2 ​ ​ = d r ​

Power scales linearly with density: BHP 2 BHP 1 = ρ 2 ρ 1 = d r \frac{\text{BHP}_2}{\text{BHP}_1} = \frac{\rho_2}{\rho_1} = d_r BHP 1 ​ BHP 2 ​ ​ = ρ 1 ​ ρ 2 ​ ​ = d r ​

Where d r = ρ act ρ std = ( P baro, act 29.921 ) ( 530 T act + 460 ) d_r = \frac{\rho_{\text{act}}}{\rho_{\text{std}}} = \left(\frac{P_{\text{baro, act}}}{29.921}\right) \left(\frac{530}{T_{\text{act}} + 460}\right) d r ​ = ρ std ​ ρ act ​ ​ = ( 29.921 P baro, act ​ ​ ) ( T act ​ + 460 530 ​ ) is the density ratio.

4. AMCA 201 System Effect Factors (SEF)

Fan manufacturers test and publish catalog performance curves based on idealized AMCA Standard 210 laboratory test configurations featuring long, unobstructed ductwork on fan discharge ( 2.5 2.5 2.5 to 6.0 6.0 6.0 equivalent duct diameters) and a uniform, swirl-free inlet plenum.

In actual building mechanical rooms, cramped space constraints force suboptimal fittings directly at fan connections (e.g., elbows attached directly to fan discharge, eccentric inlet transitions, or obstructions near the inlet cone). These disturbances induce non-uniform velocity profiles, flow separation, and inlet swirl that degrade fan aerodynamic head generation. AMCA LABORATORY RATING TEST: REAL MECHANICAL ROOM INSTALLATION:

(Ideal Velocity Profile, Zero SEF) (Severe System Effect: SEF added to System Curve)

2.5 to 6.0 Diameters Abrupt Elbow at Discharge!

  • [Fan] ===> [ Long Straight Duct ] ===> [Fan] ==[Elbow]===/
  • (Full Effective Duct Length) | (Separation & Turbulence)
  • v (Fan underperforms catalog CFM)
  • Quantifying System Effect

The System Effect Factor (SEF) is an additional dynamic pressure loss ( in. wg \text{in. wg} in. wg ) that must be added to the calculated system resistance curve: P fan, catalog required = Δ P calculated duct system + SEF inlet + SEF discharge P_{\text{fan, catalog required}} = \Delta P_{\text{calculated duct system}} + \text{SEF}_{\text{inlet}} + \text{SEF}_{\text{discharge}} P fan, catalog required ​ = Δ P calculated duct system ​ + SEF inlet ​ + SEF discharge ​

100% Effective Duct Length ( L e L_e L e ​ )

To achieve rated catalog performance without discharge System Effect, fan discharge ductwork must provide a straight run equal to the 100% Effective Duct Length ( L e L_e L e ​ ) : For V o > 2 , 500 FPM: L e (ft) = V o (FPM) 1 , 000 × a ⋅ b 2.5 \text{For } V_o > 2,500\text{ FPM: } L_e\text{ (ft)} = \frac{V_o\text{ (FPM)}}{1,000} \times \frac{\sqrt{a \cdot b}}{2.5} For V o ​ > 2 , 500 FPM: L e ​ (ft) = 1 , 000 V o ​ (FPM) ​ × 2.5 a ⋅ b ​ ​ For V o ≤ 2 , 500 FPM: L e (ft) = 2.5 × D e \text{For } V_o \le 2,500\text{ FPM: } L_e\text{ (ft)} = 2.5 \times D_e For V o ​ ≤ 2 , 500 FPM: L e ​ (ft) = 2.5 × D e ​

Where V o V_o V o ​ is fan discharge outlet velocity and D e D_e D e ​ is equivalent duct diameter.

  • 5. Aerodynamic Stall, Surge & Paralleling Dynamics Fan Static Pressure (FSP)
  • ^
  • | SURGE / STALL REGION
  • Ps | (Unstable Dip)
  • Peak +----\ /-------------\ Airfoil Fan Curve
  • | \ Stall / \
  • | \ Dip / \ Operating Point (Intersection)
  • | '---------' \====*==================
  • | \ / System Curve: dP = K * CFM^2
  • | <--- UNSTABLE --->|<-- STABLE --> \/
  • +---------------------+------------------+---------------------> Airflow (CFM)
  • Q_stall

Aerodynamic Stall: Occurs when airflow across fan blades drops below design threshold at high static pressure. Fluid streamlines detach from the blade suction surface, forming violent recirculation vortices, loss of lift, and low-frequency rumble ( 10 10 10 to 30 Hz 30\text{ Hz} 30 Hz ). Forward-curved and axial fans exhibit a prominent "dip" or saddle in their pressure curve.

Surge: System-wide pressure oscillation caused by cycling between stalled and unstalled flow regimes. Causes severe duct hunting and thrust bearing destruction.

Paralleling Fans: When two identical fans operate in parallel (sharing common headers), their combined curve is generated by adding flow rates ( CFM \text{CFM} CFM ) at each static pressure. If the combined operating point falls in or near the unstable dip region, one fan will hunt, stall, or backflow through the other, leading to severe aerodynamic imbalance.

6. Worked Example: Fan Operating Point, VFD Modulation & Altitude Correction

Problem: A commercial airfoil supply fan operates at sea level ( 70 ∘ F 70^\circ\text{F} 7 0 ∘ F , ρ = 0.075 lbm/ft 3 \rho = 0.075\text{ lbm/ft}^3 ρ = 0.075 lbm/ft 3 ) running at N 1 = 1 , 200 RPM N_1 = 1,200\text{ RPM} N 1 ​ = 1 , 200 RPM . It delivers CFM 1 = 15 , 000 CFM \text{CFM}_1 = 15,000\text{ CFM} CFM 1 ​ = 15 , 000 CFM against a system static pressure of FSP 1 = 3.20 in. wg \text{FSP}_1 = 3.20\text{ in. wg} FSP 1 ​ = 3.20 in. wg with a static efficiency of η s = 0.74 \eta_s = 0.74 η s ​ = 0.74 .

Part A: Calculate the initial Fan Brake Horsepower ( BHP 1 \text{BHP}_1 BHP 1 ​ ).

Part B: The building control system reduces airflow to CFM 2 = 10 , 500 CFM \text{CFM}_2 = 10,500\text{ CFM} CFM 2 ​ = 10 , 500 CFM via a VFD. Assuming a fixed system resistance curve ( Δ P = K ⋅ CFM 2 \Delta P = K \cdot \text{CFM}^2 Δ P = K ⋅ CFM 2 ), calculate the new fan speed ( N 2 N_2 N 2 ​ ), the new operating static pressure ( FSP 2 \text{FSP}_2 FSP 2 ​ ), and the new brake horsepower ( BHP 2 \text{BHP}_2 BHP 2 ​ ).

Part C: The exact same fan and motor are relocated to a facility in Denver, Colorado (elevation 5 , 280 ft 5,280\text{ ft} 5 , 280 ft , barometric pressure P baro = 24.60 in. Hg P_{\text{baro}} = 24.60\text{ in. Hg} P baro ​ = 24.60 in. Hg , design temperature 70 ∘ F 70^\circ\text{F} 7 0 ∘ F ). If the fan runs at the original speed N 1 = 1 , 200 RPM N_1 = 1,200\text{ RPM} N 1 ​ = 1 , 200 RPM , calculate the volumetric flow rate ( CFM Denver \text{CFM}_{\text{Denver}} CFM Denver ​ ), actual developed static pressure ( FSP Denver \text{FSP}_{\text{Denver}} FSP Denver ​ ), and actual power ( BHP Denver \text{BHP}_{\text{Denver}} BHP Denver ​ ).

Step-by-Step Solution:

Part A: Calculate initial Brake Horsepower (BHP1): BHP 1 = CFM 1 × FSP 1 6 , 356 × η s = 15 , 000 CFM × 3.20 in. wg 6 , 356 × 0.74 = 48 , 000 4 , 703.44 = 10.205 BHP \text{BHP}_1 = \frac{\text{CFM}_1 \times \text{FSP}_1}{6,356 \times \eta_s} = \frac{15,000\text{ CFM} \times 3.20\text{ in. wg}}{6,356 \times 0.74} = \frac{48,000}{4,703.44} = 10.205\text{ BHP} BHP 1 ​ = 6 , 356 × η s ​ CFM 1 ​ × FSP 1 ​ ​ = 6 , 356 × 0.74 15 , 000 CFM × 3.20 in. wg ​ = 4 , 703.44 48 , 000 ​ = 10.205 BHP

Part B: Calculate performance at reduced airflow (10,500 CFM): Speed Ratio: N 2 N 1 = CFM 2 CFM 1 = 10 , 500 15 , 000 = 0.700 \text{Speed Ratio: } \frac{N_2}{N_1} = \frac{\text{CFM}_2}{\text{CFM}_1} = \frac{10,500}{15,000} = 0.700 Speed Ratio: N 1 ​ N 2 ​ ​ = CFM 1 ​ CFM 2 ​ ​ = 15 , 000 10 , 500 ​ = 0.700 N 2 = 1 , 200 RPM × 0.700 = 840 RPM N_2 = 1,200\text{ RPM} \times 0.700 = 840\text{ RPM} N 2 ​ = 1 , 200 RPM × 0.700 = 840 RPM FSP 2 = FSP 1 × ( N 2 N 1 ) 2 = 3.20 in. wg × ( 0.700 ) 2 = 3.20 × 0.490 = 1.568 in. wg \text{FSP}_2 = \text{FSP}_1 \times \left(\frac{N_2}{N_1}\right)^2 = 3.20\text{ in. wg} \times (0.700)^2 = 3.20 \times 0.490 = 1.568\text{ in. wg} FSP 2 ​ = FSP 1 ​ × ( N 1 ​ N 2 ​ ​ ) 2 = 3.20 in. wg × ( 0.700 ) 2 = 3.20 × 0.490 = 1.568 in. wg BHP 2 = BHP 1 × ( N 2 N 1 ) 3 = 10.205 BHP × ( 0.700 ) 3 = 10.205 × 0.343 = 3.500 BHP \text{BHP}_2 = \text{BHP}_1 \times \left(\frac{N_2}{N_1}\right)^3 = 10.205\text{ BHP} \times (0.700)^3 = 10.205 \times 0.343 = 3.500\text{ BHP} BHP 2 ​ = BHP 1 ​ × ( N 1 ​ N 2 ​ ​ ) 3 = 10.205 BHP × ( 0.700 ) 3 = 10.205 × 0.343 = 3.500 BHP Power Reduction = 10.205 − 3.500 10.205 × 100 % = 65.7 % energy saved! \text{Power Reduction} = \frac{10.205 - 3.500}{10.205} \times 100\% = 65.7\%\text{ energy saved!} Power Reduction = 10.205 10.205 − 3.500 ​ × 100% = 65.7% energy saved!

Part C: Denver Density Correction: Density Ratio: d r = P baro, act 29.921 × 530 T act + 460 = 24.60 29.921 × 530 530 = 0.82216 \text{Density Ratio: } d_r = \frac{P_{\text{baro, act}}}{29.921} \times \frac{530}{T_{\text{act}} + 460} = \frac{24.60}{29.921} \times \frac{530}{530} = 0.82216 Density Ratio: d r ​ = 29.921 P baro, act ​ ​ × T act ​ + 460 530 ​ = 29.921 24.60 ​ × 530 530 ​ = 0.82216 ρ Denver = 0.075 × 0.82216 = 0.06166 lbm/ft 3 \rho_{\text{Denver}} = 0.075 \times 0.82216 = 0.06166\text{ lbm/ft}^3 ρ Denver ​ = 0.075 × 0.82216 = 0.06166 lbm/ft 3

Volumetric Flow Rate: Constant displacement turbomachine ⟹ CFM Denver = 15 , 000 CFM \implies \text{CFM}_{\text{Denver}} = 15,000\text{ CFM} ⟹ CFM Denver ​ = 15 , 000 CFM .

Actual Static Pressure: FSP Denver = FSP std × d r = 3.20 in. wg × 0.82216 = 2.631 in. wg \text{FSP}_{\text{Denver}} = \text{FSP}_{\text{std}} \times d_r = 3.20\text{ in. wg} \times 0.82216 = 2.631\text{ in. wg} FSP Denver ​ = FSP std ​ × d r ​ = 3.20 in. wg × 0.82216 = 2.631 in. wg

Actual Brake Horsepower: BHP Denver = BHP std × d r = 10.205 BHP × 0.82216 = 8.390 BHP \text{BHP}_{\text{Denver}} = \text{BHP}_{\text{std}} \times d_r = 10.205\text{ BHP} \times 0.82216 = 8.390\text{ BHP} BHP Denver ​ = BHP std ​ × d r ​ = 10.205 BHP × 0.82216 = 8.390 BHP

7. NCEES Reference Handbook Navigation & Exam Tips

Fan Affinity Laws: Look under Fan and Pump Laws in the Mechanical Engineering Reference Handbook: Q 1 Q 2 = N 1 N 2 \frac{Q_1}{Q_2} = \frac{N_1}{N_2} Q 2 ​ Q 1 ​ ​ = N 2 ​ N 1 ​ ​ , P 1 P 2 = ( N 1 N 2 ) 2 ρ 1 ρ 2 \frac{P_1}{P_2} = (\frac{N_1}{N_2})^2 \frac{\rho_1}{\rho_2} P 2 ​ P 1 ​ ​ = ( N 2 ​ N 1 ​ ​ ) 2 ρ 2 ​ ρ 1 ​ ​ , BHP 1 BHP 2 = ( N 1 N 2 ) 3 ρ 1 ρ 2 \frac{\text{BHP}_1}{\text{BHP}_2} = (\frac{N_1}{N_2})^3 \frac{\rho_1}{\rho_2} BHP 2 ​ BHP 1 ​ ​ = ( N 2 ​ N 1 ​ ​ ) 3 ρ 2 ​ ρ 1 ​ ​ .

Density Invariance: Memorize that volumetric flow rate ( CFM \text{CFM} CFM ) does NOT change with altitude or temperature for a fixed RPM fan.

Horsepower Constant: Always remember 6 , 356 6,356 6 , 356 in the denominator of BHP = CFM ⋅ Δ P 6 , 356 ⋅ η \text{BHP} = \frac{\text{CFM} \cdot \Delta P}{6,356 \cdot \eta} BHP = 6 , 356 ⋅ η CFM ⋅ Δ P ​ .

Loading diagram... Fan Performance Curves & System Effect