Study guide

13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models

PE Mechanical: HVAC and Refrigeration Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations

1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)

2 Chapter 2: Thermodynamics & Energy Balances

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment

3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment

3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes

4 Chapter 4: Heat Transfer Principles & Sizing

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)

5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals

5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves

6 Chapter 6: Heating & Cooling Load Calculations

6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis

7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design

8 Chapter 8: Refrigerants, Environmental Regulations & Safety

8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers

9 Chapter 9: HVAC Equipment & Primary Machinery

9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems

10 Chapter 10: Air-Side Systems & Distribution

10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection

11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant

11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems

12 Chapter 12: HVAC Control Concepts, Sensors & Sequences

12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences

13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes

13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops

14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations

14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)

13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models

Key Takeaways Explain This Topic AI

ASHRAE Standard 55 defines thermal comfort as that condition of mind that expresses satisfaction with the thermal environment, specifying conditions where at least 80% of occupants find the environment acceptable (PPD <= 10% for the general thermal environment, corresponding to -0.5 <= PMV <= +0.5).

Thermal comfort is governed by six primary variables: four environmental factors (dry-bulb air temperature, mean radiant temperature T_mrt, relative air velocity v_r, and relative humidity / water vapor pressure) and two personal factors (clothing insulation I_cl in clo, and metabolic rate M in met).

Operative temperature (T_o) integrates convective (air) and radiant heat transfer: at low air speeds (<= 40 fpm / 0.2 m/s), T_o is the direct arithmetic average of air temperature and mean radiant temperature (T_o = (T_a + T_mrt) / 2).

The Adaptive Comfort Model applies exclusively to occupant-controlled naturally ventilated spaces without mechanical cooling, determining allowable indoor operative comfort temperatures as a function of the prevailing mean outdoor air temperature: T_c = 17.8 + 0.31 * T_pma(out) (°C).

Last updated: August 2026

13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models

Thermal comfort is defined by ASHRAE Standard 55 ( Thermal Environmental Conditions for Human Occupancy ) as "that condition of mind that expresses satisfaction with the thermal environment and is assessed by subjective evaluation." Because human thermal sensation varies based on physiological, metabolic, and psychological differences, environmental control systems are engineered to satisfy a target percentage of occupants (typically ≥ 80 % \ge 80\% ≥ 80% satisfied, with ≤ 10 % \le 10\% ≤ 10% dissatisfied due to general body thermal sensation and ≤ 10 % \le 10\% ≤ 10% dissatisfied due to local thermal discomfort).

1. The Six Primary Factors of Thermal Comfort

Human energy balance is dictated by four environmental parameters and two personal parameters: +---------------------------------------------------------------------------------------------------------+

  • | THE SIX CORE THERMAL COMFORT VARIABLES |
  • +---------------------------------------------------------------------------------------------------------+
  • | ENVIRONMENTAL FACTORS: |
  • | 1. Air Temperature (T_a): Dry-bulb temperature of air surrounding the occupant. |
  • | 2. Mean Radiant Temperature (T_mrt): Uniform surface temperature of an imaginary black enclosure |
  • | exchanging the same radiant heat as the actual non-uniform environment. |
  • | 3. Relative Air Velocity (v_r): Air speed relative to occupant motion (affects convective/evaporative).|
  • | 4. Humidity / Vapor Pressure (p_a): Moisture content of ambient air affecting skin sweat evaporation. |
  • | |
  • | PERSONAL FACTORS: |
  • | 5. Metabolic Rate (M): Heat production rate generated by human physical activity. |
  • | 1 met = 50 kcal/(h·m2) = 58.2 W/m2 = 18.4 Btu/(h·ft2). (Seated resting = 1.0 met; office = 1.2 met)|
  • | 6. Clothing Insulation (I_cl): Thermal resistance of garment ensembles. |
  • | 1 clo = 0.155 m2·K/W = 0.88 h·ft2·°F/Btu. (Summer shorts/polo = 0.5 clo; Winter suit = 1.0 clo) |
  • +---------------------------------------------------------------------------------------------------------+
  • 2. Operative Temperature ( T o T_o T o ​ ) & Mean Radiant Temperature ( T mrt T_{\text{mrt}} T mrt ​ )

The human body exchanges heat simultaneously via convection with surrounding air ( T a T_a T a ​ ) and radiation with surrounding envelope surfaces ( T mrt T_{\text{mrt}} T mrt ​ ). The Operative Temperature ( T o T_o T o ​ ) combines these into a single uniform temperature: T o = h c T a + h r T mrt h c + h r T_o = \frac{h_c T_a + h_r T_{\text{mrt}}}{h_c + h_r} T o ​ = h c ​ + h r ​ h c ​ T a ​ + h r ​ T mrt ​ ​

Where:

h c = Convective heat transfer coefficient ( W / ( m 2 ⋅ K ) or Btu / ( h ⋅ ft 2 ⋅ ∘ F ) ) h_c = \text{Convective heat transfer coefficient } (\text{W}/(\text{m}^2\cdot\text{K}) \text{ or } \text{Btu}/(\text{h}\cdot\text{ft}^2\cdot^\circ\text{F})) h c ​ = Convective heat transfer coefficient ( W / ( m 2 ⋅ K ) or Btu / ( h ⋅ ft 2 ⋅ ∘ F ))

h r = Radiative heat transfer coefficient ( ≈ 4.5 − 5.0 W / ( m 2 ⋅ K ) ≈ 0.8 Btu / ( h ⋅ ft 2 ⋅ ∘ F ) ) h_r = \text{Radiative heat transfer coefficient } (\approx 4.5 - 5.0\text{ W}/(\text{m}^2\cdot\text{K}) \approx 0.8\text{ Btu}/(\text{h}\cdot\text{ft}^2\cdot^\circ\text{F})) h r ​ = Radiative heat transfer coefficient ( ≈ 4.5 − 5.0 W / ( m 2 ⋅ K ) ≈ 0.8 Btu / ( h ⋅ ft 2 ⋅ ∘ F ))

At standard indoor air speeds ( v ≤ 40 fpm v \le 40\text{ fpm} v ≤ 40 fpm or 0.2 m/s 0.2\text{ m/s} 0.2 m/s ), h c ≈ h r h_c \approx h_r h c ​ ≈ h r ​ , simplifying the operative temperature to the direct arithmetic mean: T o ≈ 0.5 T a + 0.5 T mrt = T a + T mrt 2 T_o \approx 0.5 T_a + 0.5 T_{\text{mrt}} = \frac{T_a + T_{\text{mrt}}}{2} T o ​ ≈ 0.5 T a ​ + 0.5 T mrt ​ = 2 T a ​ + T mrt ​ ​

At elevated air velocities ( v > 40 fpm v > 40\text{ fpm} v > 40 fpm ): T o = A T a + ( 1 − A ) T mrt T_o = A T_a + (1 - A) T_{\text{mrt}} T o ​ = A T a ​ + ( 1 − A ) T mrt ​

Where A = 0.5 A = 0.5 A = 0.5 for v < 0.2 m/s v < 0.2\text{ m/s} v < 0.2 m/s ( 40 fpm 40\text{ fpm} 40 fpm ), A = 0.6 A = 0.6 A = 0.6 for 0.2 ≤ v < 0.6 m/s 0.2 \le v < 0.6\text{ m/s} 0.2 ≤ v < 0.6 m/s , and A = 0.7 A = 0.7 A = 0.7 for 0.6 ≤ v ≤ 1.0 m/s 0.6 \le v \le 1.0\text{ m/s} 0.6 ≤ v ≤ 1.0 m/s .

Mean Radiant Temperature Calculation

For an enclosure of N N N surrounding surfaces with surface temperatures T i T_i T i ​ and angle/view factors F p − i F_{p-i} F p − i ​ relative to the person (where ∑ F p − i = 1.0 \sum F_{p-i} = 1.0 ∑ F p − i ​ = 1.0 ): T mrt 4 = ∑ i = 1 N F p − i T i 4 (Temperatures in Rankine or Kelvin) T_{\text{mrt}}^4 = \sum_{i=1}^N F_{p-i} T_i^4 \quad \text{(Temperatures in Rankine or Kelvin)} T mrt 4 ​ = i = 1 ∑ N ​ F p − i ​ T i 4 ​ (Temperatures in Rankine or Kelvin)

For small temperature differences ( ∣ T i − T mrt ∣ < 30 ∘ F |T_i - T_{\text{mrt}}| < 30^\circ\text{F} ∣ T i ​ − T mrt ​ ∣ < 3 0 ∘ F ), the linearized form is accurate: T mrt ≈ ∑ i = 1 N F p − i T i T_{\text{mrt}} \approx \sum_{i=1}^N F_{p-i} T_i T mrt ​ ≈ i = 1 ∑ N ​ F p − i ​ T i ​

Globe Thermometer Measurement

In field assessments, T mrt T_{\text{mrt}} T mrt ​ is measured using a standard 6 inch 6\text{ inch} 6 inch ( 150 mm 150\text{ mm} 150 mm ) black globe thermometer: T mrt = [ ( T g + 273.15 ) 4 + 1.10 × 10 8 ⋅ v 0.6 ϵ ⋅ D 0.4 ( T g − T a ) ] 1 / 4 − 273.15 T_{\text{mrt}} = \left[ (T_g + 273.15)^4 + \frac{1.10 \times 10^8 \cdot v^{0.6}}{\epsilon \cdot D^{0.4}} (T_g - T_a) \right]^{1/4} - 273.15 T mrt ​ = [ ( T g ​ + 273.15 ) 4 + ϵ ⋅ D 0.4 1.10 × 1 0 8 ⋅ v 0.6 ​ ( T g ​ − T a ​ ) ] 1/4 − 273.15

Where T g T_g T g ​ is globe temperature ( ∘ C ^\circ\text{C} ∘ C ), v v v is air speed ( m/s \text{m/s} m/s ), D D D is globe diameter ( m \text{m} m ), and ϵ \epsilon ϵ is emissivity ( ≈ 0.95 \approx 0.95 ≈ 0.95 ).

3. Fanger's PMV and PPD Mathematical Models

Developed by P.O. Fanger, the Predicted Mean Vote (PMV) predicts the average thermal sensation vote of a large population of people on the ASHRAE 7-point thermal sensation scale, derived from human heat balance equations: +---------------------------------------------------------------------------------------------------------+

  • | ASHRAE 7-POINT THERMAL SENSATION SCALE |
  • +---------------------------------------------------------------------------------------------------------+
  • | +3 : Hot |
  • | +2 : Warm |
  • | +1 : Slightly Warm |
  • | 0 : Neutral (Optimal thermal comfort) |
  • | -1 : Slightly Cool |
  • | -2 : Cool |
  • | -3 : Cold |
  • +---------------------------------------------------------------------------------------------------------+
  • Standard 55 General Thermal Comfort Envelope

To comply with Standard 55 via the PMV model: − 0.5 ≤ PMV ≤ + 0.5 -0.5 \le \text{PMV} \le +0.5 − 0.5 ≤ PMV ≤ + 0.5

Predicted Percentage Dissatisfied (PPD)

The Predicted Percentage of Dissatisfied (PPD) represents the quantitative percentage of occupants who will feel thermally uncomfortable (voting + 3 , + 2 , − 2 +3, +2, -2 + 3 , + 2 , − 2 , or − 3 -3 − 3 ). PPD is related non-linearly to PMV: PPD = 100 − 95 ⋅ exp ⁡ [ − ( 0.03353 ⋅ PMV 4 + 0.2179 ⋅ PMV 2 ) ] \text{PPD} = 100 - 95 \cdot \exp \left[ -\left( 0.03353 \cdot \text{PMV}^4 + 0.2179 \cdot \text{PMV}^2 \right) \right] PPD = 100 − 95 ⋅ exp [ − ( 0.03353 ⋅ PMV 4 + 0.2179 ⋅ PMV 2 ) ] +---------------------------------------------------------------------------------------------------------+

  • | FANGER PMV VS. PPD CHARACTERISTIC CURVE |
  • +---------------------------------------------------------------------------------------------------------+
  • | PPD (%) |
  • | 100% | * |
  • | 80% | |
  • | 60% | * * |
  • | 40% | |
  • | 20% | * * |
  • | 10% |---------------------------[======= COMFORT =======]-------------------------------------------|
  • | 5% | * |
  • | 0% +-------+-------+-------+-------+-------+-------+-------+-------+ |
  • | -3 -2 -1 -0.5 0 +0.5 +1 +2 +3 (PMV) |
  • +---------------------------------------------------------------------------------------------------------+
  • Key PMV/PPD Benchmark Values

When PMV = 0.0 \text{PMV} = 0.0 PMV = 0.0 (thermal neutrality): PPD = 5 % \text{PPD} = \mathbf{5\%} PPD = 5% (5% baseline dissatisfaction due to individual biological variation).

When PMV = ± 0.5 \text{PMV} = \pm 0.5 PMV = ± 0.5 (Standard 55 boundary): PPD = 10 % \text{PPD} = \mathbf{10\%} PPD = 10% .

When PMV = ± 1.0 \text{PMV} = \pm 1.0 PMV = ± 1.0 : PPD = 26.1 % \text{PPD} = \mathbf{26.1\%} PPD = 26.1% .

When PMV = ± 2.0 \text{PMV} = \pm 2.0 PMV = ± 2.0 : PPD = 76.8 % \text{PPD} = \mathbf{76.8\%} PPD = 76.8% .

4. Local Thermal Discomfort Criteria

Even when the overall body is in thermal neutrality ( PMV = 0 \text{PMV} = 0 PMV = 0 ), occupants may experience acute discomfort due to localized thermal asymmetry. Standard 55 establishes strict limits across four independent local discomfort mechanisms: +---------------------------------------------------------------------------------------------------------+

  • | FOUR MECHANISMS OF LOCAL THERMAL DISCOMFORT |
  • +------------------------------------+----------------------------------+---------------------------------+
  • | DISCOMFORT MECHANISM | PHYSICAL THRESHOLD LIMIT | MAXIMUM DISSATISFACTION CRITERIA|
  • +------------------------------------+----------------------------------+---------------------------------+
  • | 1. Draft Rate (DR) | Air speed v <= 30-40 fpm | DR <= 20% |
  • | | (at Tu = 40%, T_a = 72°F) | |
  • +------------------------------------+----------------------------------+---------------------------------+
  • | 2. Vertical Temperature Gradient | Delta_T (head to ankle) <= 5.4°F | Dissatisfaction <= 5% |
  • | (Head 43" vs. Ankle 4" seated) | (3.0°C) | |
  • +------------------------------------+----------------------------------+---------------------------------+
  • | 3. Floor Surface Temperature | 66°F <= T_floor <= 84°F | Dissatisfaction <= 10% |
  • | | (19°C to 29°C for occupants with | |
  • | | standard footwear) | |
  • +------------------------------------+----------------------------------+---------------------------------+
  • | 4. Radiant Temperature Asymmetry | Warm Ceiling: Delta_T_pr <= 9°F | Warm Ceiling: <= 5% |
  • | (Plane radiant temp difference | Cool Wall: Delta_T_pr <= 25°F | Cool Wall: <= 10% |
  • | Delta_T_pr) | Cool Ceiling: Delta_T_pr <= 25°F | Cool Ceiling: <= 5% |
  • | | Warm Wall: Delta_T_pr <= 41°F | Warm Wall: <= 5% |
  • +------------------------------------+----------------------------------+---------------------------------+

Mathematical Formulation for Draft Rate (DR) DR = ( ( 34 − T a ) ( v − 0.05 ) 0.62 ) × ( 0.37 ⋅ v ⋅ T u + 3.14 ) [ % ] ( for v ≥ 0.05 m/s ) \text{DR} = \left( (34 - T_a)(v - 0.05)^{0.62} \right) \times (0.37 \cdot v \cdot Tu + 3.14) \quad [\%] \quad (\text{for } v \ge 0.05\text{ m/s}) DR = ( ( 34 − T a ​ ) ( v − 0.05 ) 0.62 ) × ( 0.37 ⋅ v ⋅ T u + 3.14 ) [ % ] ( for v ≥ 0.05 m/s )

Where T a T_a T a ​ is air temp ( ∘ C ^\circ\text{C} ∘ C ), v v v is local mean air speed ( m/s \text{m/s} m/s ), and T u Tu T u is turbulence intensity ( T u = 100 × σ v / v [ % ] Tu = 100 \times \sigma_v / v [\%] T u = 100 × σ v ​ / v [ % ] ).

5. The Adaptive Thermal Comfort Model

The Adaptive Comfort Model is based on the principle that in naturally ventilated buildings without mechanical cooling, occupants adapt their clothing, metabolic rhythm, window openings, and thermal expectations in response to prevailing outdoor weather patterns.

Applicability Constraints

Applies ONLY to occupant-controlled naturally conditioned spaces where operable windows open directly to outdoors.

Mechanical cooling systems must NOT be running in the space.

Occupants must be engaged in sedentary activity ( 1.0 − 1.5 met 1.0 - 1.5\text{ met} 1.0 − 1.5 met ) with free clothing adaptation ( 0.5 − 1.0 clo 0.5 - 1.0\text{ clo} 0.5 − 1.0 clo ).

Prevailing mean outdoor temperature must be within: 10.0 ∘ C ≤ T pma(out) ≤ 33.5 ∘ C 10.0^\circ\text{C} \le T_{\text{pma(out)}} \le 33.5^\circ\text{C} 10. 0 ∘ C ≤ T pma(out) ​ ≤ 33. 5 ∘ C ( 50 ∘ F ≤ T pma(out) ≤ 92.3 ∘ F 50^\circ\text{F} \le T_{\text{pma(out)}} \le 92.3^\circ\text{F} 5 0 ∘ F ≤ T pma(out) ​ ≤ 92. 3 ∘ F ).

Adaptive Comfort Equations Optimal Operative Comfort Temperature: T c = 17.8 + 0.31 ⋅ T pma(out) ( ∘ C ) \text{Optimal Operative Comfort Temperature: } T_{c} = 17.8 + 0.31 \cdot T_{\text{pma(out)}} \quad (^\circ\text{C}) Optimal Operative Comfort Temperature: T c ​ = 17.8 + 0.31 ⋅ T pma(out) ​ ( ∘ C ) In IP Units: T c = 60.4 + 0.31 ⋅ ( T pma(out) − 32 ) ( ∘ F ) \text{In IP Units: } T_c = 60.4 + 0.31 \cdot (T_{\text{pma(out)}} - 32) \quad (^\circ\text{F}) In IP Units: T c ​ = 60.4 + 0.31 ⋅ ( T pma(out) ​ − 32 ) ( ∘ F )

Where T pma(out) T_{\text{pma(out)}} T pma(out) ​ is the prevailing mean outdoor air temperature, calculated as an exponentially weighted rolling average of the preceding 7 to 30 sequential days: T pma(out) = ( 1 − α ) ⋅ [ T e ( d − 1 ) + α T e ( d − 2 ) + α 2 T e ( d − 3 ) + … ] ( where α ≈ 0.7 − 0.8 ) T_{\text{pma(out)}} = (1 - \alpha) \cdot \left[ T_{e(d-1)} + \alpha T_{e(d-2)} + \alpha^2 T_{e(d-3)} + \dots \right] \quad (\text{where } \alpha \approx 0.7 - 0.8) T pma(out) ​ = ( 1 − α ) ⋅ [ T e ( d − 1 ) ​ + α T e ( d − 2 ) ​ + α 2 T e ( d − 3 ) ​ + … ] ( where α ≈ 0.7 − 0.8 )

Acceptability Temperature Ranges

80 % 80\% 80% Acceptability Limit (Standard Design Target): T o = T c ± 3.5 ∘ C ( T o = T c ± 6.3 ∘ F ) T_o = T_c \pm 3.5^\circ\text{C} \quad (T_o = T_c \pm 6.3^\circ\text{F}) T o ​ = T c ​ ± 3. 5 ∘ C ( T o ​ = T c ​ ± 6. 3 ∘ F )

90 % 90\% 90% Acceptability Limit (High-Performance Target): T o = T c ± 2.5 ∘ C ( T o = T c ± 4.5 ∘ F ) T_o = T_c \pm 2.5^\circ\text{C} \quad (T_o = T_c \pm 4.5^\circ\text{F}) T o ​ = T c ​ ± 2. 5 ∘ C ( T o ​ = T c ​ ± 4. 5 ∘ F ) +---------------------------------------------------------------------------------------------------------+

  • | ADAPTIVE COMFORT CHART (ASHRAE 55) |
  • +---------------------------------------------------------------------------------------------------------+
  • | Indoor Operative Temp (°C) |
  • | 30 | / -------- 80% Upper (Tc + 3.5°C) |
  • | 28 | / ----- / -------- 90% Upper (Tc + 2.5°C) |
  • | 26 | / ----- / -----/ |
  • | 24 | / ----- / -----/ -----/ <--- Optimum Centerline (Tc = 17.8 + 0.31*T_out)|
  • | 22 | / ----- / -----/ -----/ |
  • | 20 | / ----- / -----/ -----/ -------- 90% Lower (Tc - 2.5°C) |
  • | 18 | ----- / -----/ -----/ ---------------- 80% Lower (Tc - 3.5°C) |
  • | +-------+-------+-------+-------+-------+-------+-------+ |
  • | 10 14 18 22 26 30 34 Prevailing Mean Outdoor Temp (°C) |
  • +---------------------------------------------------------------------------------------------------------+
  • 6. Worked Engineering Calculation: Operative Temperature & Radiant Asymmetry
  • Problem Statement

An occupant sits in an office near an uninsulated single-pane exterior glass window on a cold winter day. The ambient indoor air temperature is T a = 72.0 ∘ F T_a = 72.0^\circ\text{F} T a ​ = 72. 0 ∘ F , and the room air velocity is v = 20 fpm v = 20\text{ fpm} v = 20 fpm ( 0.10 m/s 0.10\text{ m/s} 0.10 m/s ). The interior surface temperatures and corresponding view factors relative to the seated occupant are:

Window (Wall 1): T 1 = 45.0 ∘ F T_1 = 45.0^\circ\text{F} T 1 ​ = 45. 0 ∘ F , F p − 1 = 0.20 F_{p-1} = 0.20 F p − 1 ​ = 0.20

Interior Walls (Walls 2, 3, 4): T 2 = 70.0 ∘ F T_2 = 70.0^\circ\text{F} T 2 ​ = 70. 0 ∘ F , F p − 2 = 0.40 F_{p-2} = 0.40 F p − 2 ​ = 0.40

Ceiling: T 3 = 74.0 ∘ F T_3 = 74.0^\circ\text{F} T 3 ​ = 74. 0 ∘ F , F p − 3 = 0.20 F_{p-3} = 0.20 F p − 3 ​ = 0.20

Floor: T 4 = 68.0 ∘ F T_4 = 68.0^\circ\text{F} T 4 ​ = 68. 0 ∘ F , F p − 4 = 0.20 F_{p-4} = 0.20 F p − 4 ​ = 0.20

Calculate:

The Mean Radiant Temperature ( T mrt T_{\text{mrt}} T mrt ​ ) using the linearized enclosure method.

The Operative Temperature ( T o T_o T o ​ ) experienced by the occupant.

The radiant asymmetry Δ T p r \Delta T_{pr} Δ T p r ​ across the occupant and verify compliance with ASHRAE 55 local discomfort limits.

Step-by-Step Solution

1. Mean Radiant Temperature ( T mrt T_{\text{mrt}} T mrt ​ ):

Apply the linearized view factor formula: T mrt = ∑ i = 1 4 F p − i T i = ( 0.20 × 45 ) + ( 0.40 × 70 ) + ( 0.20 × 74 ) + ( 0.20 × 68 ) T_{\text{mrt}} = \sum_{i=1}^4 F_{p-i} T_i = (0.20 \times 45) + (0.40 \times 70) + (0.20 \times 74) + (0.20 \times 68) T mrt ​ = i = 1 ∑ 4 ​ F p − i ​ T i ​ = ( 0.20 × 45 ) + ( 0.40 × 70 ) + ( 0.20 × 74 ) + ( 0.20 × 68 ) T mrt = 9.0 + 28.0 + 14.8 + 13.6 = 65.4 ∘ F T_{\text{mrt}} = 9.0 + 28.0 + 14.8 + 13.6 = \mathbf{65.4^\circ\text{F}} T mrt ​ = 9.0 + 28.0 + 14.8 + 13.6 = 65. 4 ∘ F

2. Operative Temperature ( T o T_o T o ​ ):

Because room air velocity v = 20 fpm ≤ 40 fpm v = 20\text{ fpm} \le 40\text{ fpm} v = 20 fpm ≤ 40 fpm ( 0.2 m/s 0.2\text{ m/s} 0.2 m/s ), the convective and radiative weighting factor is A = 0.5 A = 0.5 A = 0.5 : T o = T a + T mrt 2 = 72.0 ∘ F + 65.4 ∘ F 2 = 68.7 ∘ F T_o = \frac{T_a + T_{\text{mrt}}}{2} = \frac{72.0^\circ\text{F} + 65.4^\circ\text{F}}{2} = \mathbf{68.7^\circ\text{F}} T o ​ = 2 T a ​ + T mrt ​ ​ = 2 72. 0 ∘ F + 65. 4 ∘ F ​ = 68. 7 ∘ F

Engineering Observation: Even though the thermostat reads 72 ∘ F 72^\circ\text{F} 7 2 ∘ F , the occupant perceives an operative thermal sensation of 68.7 ∘ F 68.7^\circ\text{F} 68. 7 ∘ F due to cold radiant heat loss to the window.

3. Radiant Asymmetry Verification:

The radiant temperature of the cool window wall is 45 ∘ F 45^\circ\text{F} 4 5 ∘ F , while the opposing warm interior wall is 70 ∘ F 70^\circ\text{F} 7 0 ∘ F .

Plane radiant temperature difference: Δ T p r = 70.0 ∘ F − 45.0 ∘ F = 25.0 ∘ F \Delta T_{pr} = 70.0^\circ\text{F} - 45.0^\circ\text{F} = 25.0^\circ\text{F} Δ T p r ​ = 70. 0 ∘ F − 45. 0 ∘ F = 25. 0 ∘ F .

Under Standard 55 local discomfort rules, the allowable limit for a cool wall is Δ T p r ≤ 25.0 ∘ F \Delta T_{pr} \le 25.0^\circ\text{F} Δ T p r ​ ≤ 25. 0 ∘ F (corresponding to ≤ 10 % \le 10\% ≤ 10% dissatisfied). The window meets the threshold at the exact boundary, but double-pane low-e glass is recommended to prevent localized draft and radiant chilling.

7. NCEES Reference Handbook Navigation Strategies

Operative Temperature Formula: Search "Operative Temperature" to find T o = h c T a + h r T mrt h c + h r ≈ T a + T mrt 2 T_o = \frac{h_c T_a + h_r T_{\text{mrt}}}{h_c + h_r} \approx \frac{T_a + T_{\text{mrt}}}{2} T o ​ = h c ​ + h r ​ h c ​ T a ​ + h r ​ T mrt ​ ​ ≈ 2 T a ​ + T mrt ​ ​ .

PMV/PPD Equations: Search "Predicted Mean Vote" or "PPD" in the HVAC section to access Fanger's exponential equation and the 5 % 5\% 5% baseline dissatisfaction rule.

Adaptive Comfort: Search "Adaptive Comfort" or "Prevailing Mean" to look up T c = 17.8 + 0.31 T pma(out) T_c = 17.8 + 0.31 T_{\text{pma(out)}} T c ​ = 17.8 + 0.31 T pma(out) ​ .