Study guide

13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates

PE Mechanical: HVAC and Refrigeration Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations

1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)

2 Chapter 2: Thermodynamics & Energy Balances

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment

3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment

3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes

4 Chapter 4: Heat Transfer Principles & Sizing

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)

5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals

5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves

6 Chapter 6: Heating & Cooling Load Calculations

6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis

7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design

8 Chapter 8: Refrigerants, Environmental Regulations & Safety

8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers

9 Chapter 9: HVAC Equipment & Primary Machinery

9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems

10 Chapter 10: Air-Side Systems & Distribution

10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection

11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant

11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems

12 Chapter 12: HVAC Control Concepts, Sensors & Sequences

12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences

13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes

13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops

14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations

14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)

13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates

Key Takeaways Explain This Topic AI

ASHRAE Standard 90.1 sets minimum energy efficiency standards for commercial buildings through prescriptive criteria (envelope U-factors/SHGC, equipment minimum efficiency, economizer mandates) and performance paths (Energy Cost Budget - ECB, and Appendix G Performance Rating Method).

Airside and waterside economizers are prescriptively required for cooling systems exceeding capacity thresholds (typically >= 54,000 Btu/h or 4.5 Tons depending on climate zone), requiring 100% outdoor air capability with fully integrated compressor operation.

HVAC equipment efficiency metrics reflect full-load (COP, EER, kW/Ton) and weighted part-load performance (IEER for DX unitary systems, IPLV for chillers), where kW/Ton = 12 / EER = 3.516 / COP.

Building envelope heat gain/loss is governed by assembly thermal transmittance (U = 1 / R_total), Fenestration Solar Heat Gain Coefficient (SHGC), and mandatory continuous air barrier leakage limits (<= 0.40 CFM/ft2 at 75 Pa).

Last updated: August 2026

13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates

ASHRAE Standard 90.1 ( Energy Standard for Sites and Buildings Except Low-Rise Residential Buildings ) is the statutory benchmark for commercial building energy codes in the United States, referenced directly by the International Energy Conservation Code (IECC) and federal legislation. Standard 90.1 establishes minimum efficiency requirements for the building envelope, mechanical HVAC equipment, service water heating, power, lighting, and building motor loads.

1. Compliance Paths & Climate Zone Classification

Standard 90.1 provides three overarching compliance pathways:

Prescriptive Path (Sections 5 through 10): Compliance is achieved by meeting every individual prescriptive requirement for envelope insulation, fenestration SHGC, equipment efficiency ratings, economizer controls, and fan power limitations.

Energy Cost Budget (ECB) Method (Section 11): A performance-based approach demonstrating that the proposed building design's annual energy cost does not exceed that of a standard baseline building modeled with identical geometry, orientation, and prescriptive envelope/HVAC features.

Appendix G Performance Rating Method (PRM): Used for beyond-code green building rating programs (e.g., LEED certification) and long-term energy modeling, employing a baseline building with standardized HVAC system archetypes.

Climate Zone Framework

Requirements are structured across ASHRAE Climate Zones 0 through 8 , sub-divided by moisture regimes:

A (Humid): High latent cooling loads (e.g., Miami = Zone 1A, Houston = Zone 2A, Atlanta = Zone 3A, New York = Zone 4A, Chicago = Zone 5A).

B (Dry/Arid): High diurnal dry-bulb swing, low humidity (e.g., Phoenix = Zone 2B, Las Vegas = Zone 3B, Denver = Zone 5B).

C (Marine): Mild maritime temperatures (e.g., San Francisco = Zone 3C, Seattle = Zone 4C).

2. Building Envelope Thermal Performance

Envelope heat transfer directly drives HVAC peak sizing and annual energy consumption. Prescriptive requirements set maximum assembly U-factors ( Btu / ( h ⋅ ft 2 ⋅ ∘ F ) \text{Btu}/(\text{h}\cdot\text{ft}^2\cdot^\circ\text{F}) Btu / ( h ⋅ ft 2 ⋅ ∘ F ) ) and minimum continuous insulation (ci) R-values. +---------------------------------------------------------------------------------------------------------+

  • | BUILDING ENVELOPE HEAT FLOW RELATIONSHIPS |
  • +---------------------------------------------------------------------------------------------------------+
  • | Conductive Heat Flow: |
  • | q = U * A * Delta_T = (1 / R_total) * A * Delta_T |
  • | |
  • | Total Thermal Resistance: |
  • | R_total = R_si + R_layer1 + R_layer2 + ... + R_so |
  • | |
  • | Fenestration Total Solar Heat Gain: |
  • | q_solar = A_fen * SHGC * I_solar |
  • | |
  • | Fenestration Total Conduction Heat Flow: |
  • | q_cond = U_fen * A_fen * (T_out - T_in) |
  • +---------------------------------------------------------------------------------------------------------+
  • Thermal Bridging in Steel-Frame Assemblies

Due to the high thermal conductivity of steel ( k ≈ 314 Btu ⋅ in / ( h ⋅ ft 2 ⋅ ∘ F ) k \approx 314\text{ Btu}\cdot\text{in}/(\text{h}\cdot\text{ft}^2\cdot^\circ\text{F}) k ≈ 314 Btu ⋅ in / ( h ⋅ ft 2 ⋅ ∘ F ) ) compared to fiberglass batt insulation ( k ≈ 0.27 k \approx 0.27 k ≈ 0.27 ), cavity insulation in steel-stud walls experiences severe thermal bridging. Standard 90.1 mandates using effective R-values ( R eff R_{\text{eff}} R eff ​ ) for cavity insulation or adding exterior continuous insulation (ci) : 1 U assembly = R si + R ext finish + R continuous + R eff,cavity + R sheathing + R so \frac{1}{U_{\text{assembly}}} = R_{\text{si}} + R_{\text{ext finish}} + R_{\text{continuous}} + R_{\text{eff,cavity}} + R_{\text{sheathing}} + R_{\text{so}} U assembly ​ 1 ​ = R si ​ + R ext finish ​ + R continuous ​ + R eff,cavity ​ + R sheathing ​ + R so ​

Typical Steel-Stud Cavity Insulation Degradation

Nominal Cavity Batt Rating Actual Steel-Stud Effective R-Value ( R eff R_{\text{eff}} R eff ​ ) Parallel Path Efficiency

  • R-11 (3.5" studs) R-5.5 50 % 50\% 50%
  • R-13 (3.5" studs) R-6.0 46 % 46\% 46%
  • R-19 (6.0" studs) R-7.1 37 % 37\% 37%
  • R-25 (6.0" studs) R-7.8 31 % 31\% 31%

Design Implication: An uninsulated steel stud reduces nominal R-19 batt performance by 63 % 63\% 63% . Consequently, modern codes mandate continuous exterior insulation (e.g., R − 13 cavity + R − 7.5 ci R-13\text{ cavity} + R-7.5\text{ ci} R − 13 cavity + R − 7.5 ci ).

3. HVAC Equipment Efficiency Metrics & Conversions

Engineers must seamlessly convert between steady-state and part-load efficiency metrics across equipment categories: +---------------------------------------------------------------------------------------------------------+

  • | HVAC EFFICIENCY CONVERSION MATRIX |
  • +---------------------------------------------------------------------------------------------------------+
  • | Metric Conversions: |
  • | |
  • | COP = EER / 3.412 = (Btu/h output) / (3.412 * Watts input) |
  • | |
  • | EER = COP * 3.412 = (Btu/h output) / (Watts input) |
  • | |
  • | kW/Ton = 12 / EER = 3.516 / COP = (Watts input / 1000) / (Tons cooling) |
  • | |
  • | EER = 12 / (kW/Ton) |
  • +---------------------------------------------------------------------------------------------------------+
  • Integrated Energy Efficiency Ratio (IEER)

Unitary DX air-conditioners and heat pumps spend > 95 % > 95\% > 95% of annual operating hours at part-load. The IEER metric applies a 4-point weighted average representing part-load conditions: IEER = ( 0.020 ⋅ A ) + ( 0.617 ⋅ B ) + ( 0.238 ⋅ C ) + ( 0.125 ⋅ D ) \text{IEER} = (0.020 \cdot A) + (0.617 \cdot B) + (0.238 \cdot C) + (0.125 \cdot D) IEER = ( 0.020 ⋅ A ) + ( 0.617 ⋅ B ) + ( 0.238 ⋅ C ) + ( 0.125 ⋅ D )

Where:

A = EER at 100 % capacity with 95 ∘ F dry-bulb outdoor temp A = \text{EER at } 100\% \text{ capacity with } 95^\circ\text{F dry-bulb outdoor temp} A = EER at 100% capacity with 9 5 ∘ F dry-bulb outdoor temp

B = EER at 75 % capacity with 81.5 ∘ F dry-bulb outdoor temp B = \text{EER at } 75\% \text{ capacity with } 81.5^\circ\text{F dry-bulb outdoor temp} B = EER at 75% capacity with 81. 5 ∘ F dry-bulb outdoor temp

C = EER at 50 % capacity with 68.0 ∘ F dry-bulb outdoor temp C = \text{EER at } 50\% \text{ capacity with } 68.0^\circ\text{F dry-bulb outdoor temp} C = EER at 50% capacity with 68. 0 ∘ F dry-bulb outdoor temp

D = EER at 25 % capacity with 65.0 ∘ F dry-bulb outdoor temp D = \text{EER at } 25\% \text{ capacity with } 65.0^\circ\text{F dry-bulb outdoor temp} D = EER at 25% capacity with 65. 0 ∘ F dry-bulb outdoor temp

Integrated Part-Load Value (IPLV.IP) for Chillers

For water-cooled and air-cooled chillers, IPLV is calculated using AHRI 550/590 weighting factors: IPLV (or NPLV) = ( 0.010 ⋅ A ) + ( 0.420 ⋅ B ) + ( 0.450 ⋅ C ) + ( 0.120 ⋅ D ) \text{IPLV (or NPLV)} = (0.010 \cdot A) + (0.420 \cdot B) + (0.450 \cdot C) + (0.120 \cdot D) IPLV (or NPLV) = ( 0.010 ⋅ A ) + ( 0.420 ⋅ B ) + ( 0.450 ⋅ C ) + ( 0.120 ⋅ D )

Where weights represent chiller operating hour distributions: 1 % 1\% 1% at 100 % 100\% 100% load ( A A A ), 42 % 42\% 42% at 75 % 75\% 75% load ( B B B ), 45 % 45\% 45% at 50 % 50\% 50% load ( C C C ), and 12 % 12\% 12% at 25 % 25\% 25% load ( D D D ).

4. Economizer Mandates & High-Limit Control Strategies

An economizer uses cool outdoor air (airside) or cooling tower water (waterside) to provide "free cooling" when outdoor atmospheric conditions permit, dramatically reducing compressor operating hours.

Prescriptive Capacity Trigger Thresholds

Under ASHRAE 90.1, individual cooling fan systems with design cooling capacity ≥ 54 , 000 Btu/h \ge 54,000\text{ Btu/h} ≥ 54 , 000 Btu/h ( 4.5 Tons 4.5\text{ Tons} 4.5 Tons , or 33 , 000 Btu/h 33,000\text{ Btu/h} 33 , 000 Btu/h in select versions) must include an air economizer in Climate Zones 1B, 2B, 3B, 3C, 4A, 4B, 4C, 5A, 5B, 5C, 6A, 6B, 7, and 8. Economizers are exempt only in hot-humid zones (Zone 1A) and small equipment.

Integrated Economizer Operation Mandate

Standard 90.1 strictly prohibits non-integrated economizers. The economizer control must be capable of providing partial cooling in integrated mode : when outdoor air is cool enough to handle part of the load but cannot meet the full supply setpoint, the outdoor air dampers must remain fully open ( 100 % 100\% 100% outdoor air) while compressors modulate to provide the remaining supplemental cooling. +---------------------------------------------------------------------------------------------------------+

  • | AIRSIDE ECONOMIZER OPERATIONAL MODES |
  • +---------------------------------------------------------------------------------------------------------+
  • | Mode 1: 100% Free Cooling (T_oa <= T_supply_setpoint, e.g., <= 55°F) |
  • | - Compressors OFF. Outdoor air dampers modulate to maintain 55°F supply air. |
  • | |
  • | Mode 2: Integrated Economizer (55°F < T_oa < High-Limit Shutoff, e.g., 55°F to 65°F) |
  • | - Dampers locked at 100% Outdoor Air. Compressors ON to cool air from T_oa down to 55°F. |
  • | |
  • | Mode 3: Mechanical Cooling Only (T_oa >= High-Limit Shutoff, e.g., >= 65°F) |
  • | - Economizer DISABLED. Outdoor dampers return to minimum ventilation position (V_ot). |
  • +---------------------------------------------------------------------------------------------------------+
  • Economizer High-Limit Shutoff Control Options

High-Limit Control Type Device / Sensors Shutoff Condition Prohibited Climate Zones

Fixed Dry-Bulb Outdoor dry-bulb sensor ( T oa T_{\text{oa}} T oa ​ ) T oa > 65 ∘ F T_{\text{oa}} > 65^\circ\text{F} T oa ​ > 6 5 ∘ F (or 70 ∘ F 70^\circ\text{F} 7 0 ∘ F in dry zones 2B/3B/4B/5B) Prohibited in 1A, 2A, 3A, 4A (risk of introducing high humidity)

Differential Dry-Bulb Outdoor & Return dry-bulb ( T oa , T ra T_{\text{oa}}, T_{\text{ra}} T oa ​ , T ra ​ ) T oa > T ra T_{\text{oa}} > T_{\text{ra}} T oa ​ > T ra ​ Prohibited in 1A, 2A, 3A, 4A (may draw in humid air cooler than return)

Fixed Enthalpy Outdoor enthalpy sensor ( h oa h_{\text{oa}} h oa ​ ) h oa > 28.0 Btu/lbm h_{\text{oa}} > 28.0\text{ Btu/lbm} h oa ​ > 28.0 Btu/lbm ( 65 kJ/kg 65\text{ kJ/kg} 65 kJ/kg ) dry air Allowed in all zones

Differential Enthalpy Outdoor & Return enthalpy ( h oa , h ra h_{\text{oa}}, h_{\text{ra}} h oa ​ , h ra ​ ) h oa > h ra h_{\text{oa}} > h_{\text{ra}} h oa ​ > h ra ​ Allowed in all zones

Electronic Enthalpy Microprocessor psychrometric curve Outdoor point exceeds enthalpy/dew-point curve Allowed in all zones

Waterside Economizers ("Free Cooling" Heat Exchangers)

A waterside economizer consists of a plate-and-frame heat exchanger piped in parallel or series with the chiller, enabling cooling tower water to directly cool the chilled water loop. Standard 90.1 requires waterside economizers to be capable of cooling the entire design cooling load when outdoor wet-bulb temperature is ≤ 50 ∘ F \le 50^\circ\text{F} ≤ 5 0 ∘ F ( 10 ∘ C 10^\circ\text{C} 1 0 ∘ C ) with a dry-bulb ≤ 55 ∘ F \le 55^\circ\text{F} ≤ 5 5 ∘ F .

5. Fan System Power Limitations

Standard 90.1 Section 6.5.3 caps total fan system motor nameplate horsepower (or Fan Energy Index, FEI ≥ 1.00 \ge 1.00 ≥ 1.00 ) to prevent excessive fan energy consumption.

Allowable Fan System Nameplate Motor Power Equations HP max ⁡ ≤ CFM S ⋅ 0.0011 + A (Constant Volume Systems) \text{HP}_{\max} \le \text{CFM}_S \cdot 0.0011 + A \quad \text{(Constant Volume Systems)} HP m a x ​ ≤ CFM S ​ ⋅ 0.0011 + A (Constant Volume Systems) HP max ⁡ ≤ CFM S ⋅ 0.0015 + A (Variable Air Volume Systems) \text{HP}_{\max} \le \text{CFM}_S \cdot 0.0015 + A \quad \text{(Variable Air Volume Systems)} HP m a x ​ ≤ CFM S ​ ⋅ 0.0015 + A (Variable Air Volume Systems)

Where:

CFM S = Total supply airflow rate at design conditions \text{CFM}_S = \text{Total supply airflow rate at design conditions} CFM S ​ = Total supply airflow rate at design conditions

A = ∑ ( PD × CFM D / 4 , 131 ) = Pressure drop adjustment credit (HP) A = \sum (\text{PD} \times \text{CFM}_D / 4,131) = \text{Pressure drop adjustment credit (HP)} A = ∑ ( PD × CFM D ​ /4 , 131 ) = Pressure drop adjustment credit (HP)

PD = Design pressure drop of specific qualifying components (in. w.g.) \text{PD} = \text{Design pressure drop of specific qualifying components (in. w.g.)} PD = Design pressure drop of specific qualifying components (in. w.g.) , such as MERV 13+ filters ( 0.5 in. w.g. 0.5\text{ in. w.g.} 0.5 in. w.g. ), energy recovery devices ( 0.5 − 1.0 in. w.g. 0.5 - 1.0\text{ in. w.g.} 0.5 − 1.0 in. w.g. ), sound attenuators ( 0.15 in. w.g. 0.15\text{ in. w.g.} 0.15 in. w.g. ), and exhaust gas scrubbers.

VAV Static Pressure Reset Mandate

For VAV systems with direct digital control (DDC) down to terminal units, static pressure sensors in the supply duct must dynamically reset their static pressure setpoint downward until at least one VAV damper is nearly wide open ( 85 % 85\% 85% to 95 % 95\% 95% open). This eliminates artificial damper throttling and reduces fan brake horsepower by up to 30 % 30\% 30% to 50 % 50\% 50% at part-load.

  • 6. Worked Engineering Calculation: Chiller Plant Efficiency & Integrated Economizer
  • Problem Statement

A 500 Ton 500\text{ Ton} 500 Ton water-cooled centrifugal chiller operates with the following part-load performance ratings according to AHRI 550/590 standard rating conditions:

  • 100 % 100\% 100% Load ( 500 Tons 500\text{ Tons} 500 Tons ): Power input = 285 kW = 285\text{ kW} = 285 kW
  • 75 % 75\% 75% Load ( 375 Tons 375\text{ Tons} 375 Tons ): Power input = 175 kW = 175\text{ kW} = 175 kW
  • 50 % 50\% 50% Load ( 250 Tons 250\text{ Tons} 250 Tons ): Power input = 95 kW = 95\text{ kW} = 95 kW
  • 25 % 25\% 25% Load ( 125 Tons 125\text{ Tons} 125 Tons ): Power input = 45 kW = 45\text{ kW} = 45 kW

Calculate:

Full-load efficiency in kW/Ton \text{kW/Ton} kW/Ton , COP \text{COP} COP , and EER \text{EER} EER .

The Integrated Part-Load Value ( IPLV.IP \text{IPLV.IP} IPLV.IP ) in kW/Ton \text{kW/Ton} kW/Ton .

Compressor power required during integrated airside economizer operation when the outdoor air is at 60 ∘ F DB 60^\circ\text{F DB} 6 0 ∘ F DB with an active cooling load of 300 Tons 300\text{ Tons} 300 Tons and 10 , 000 CFM 10,000\text{ CFM} 10 , 000 CFM of 100 % 100\% 100% outdoor air entering at 60 ∘ F 60^\circ\text{F} 6 0 ∘ F cooled to 52 ∘ F 52^\circ\text{F} 5 2 ∘ F supply.

Step-by-Step Solution

1. Full-Load Efficiencies:

kW/Ton 100 % = 285 kW 500 Tons = 0.570 kW/Ton \text{kW/Ton}_{100\%} = \frac{285\text{ kW}}{500\text{ Tons}} = \mathbf{0.570\text{ kW/Ton}} kW/Ton 100% ​ = 500 Tons 285 kW ​ = 0.570 kW/Ton

COP 100 % = 3.516 kW/Ton = 3.516 0.570 = 6.168 \text{COP}_{100\%} = \frac{3.516}{\text{kW/Ton}} = \frac{3.516}{0.570} = \mathbf{6.168} COP 100% ​ = kW/Ton 3.516 ​ = 0.570 3.516 ​ = 6.168

EER 100 % = 12 kW/Ton = 12 0.570 = 21.05 Btu / ( W ⋅ h ) \text{EER}_{100\%} = \frac{12}{\text{kW/Ton}} = \frac{12}{0.570} = \mathbf{21.05\text{ Btu}/(\text{W}\cdot\text{h})} EER 100% ​ = kW/Ton 12 ​ = 0.570 12 ​ = 21.05 Btu / ( W ⋅ h )

2. Part-Load Points and IPLV Calculation:

Point A ( 100 % 100\% 100% ): kW/Ton A = 285 / 500 = 0.570 kW/Ton \text{kW/Ton}_A = 285 / 500 = 0.570\text{ kW/Ton} kW/Ton A ​ = 285/500 = 0.570 kW/Ton

Point B ( 75 % 75\% 75% ): kW/Ton B = 175 / 375 = 0.4667 kW/Ton \text{kW/Ton}_B = 175 / 375 = 0.4667\text{ kW/Ton} kW/Ton B ​ = 175/375 = 0.4667 kW/Ton

Point C ( 50 % 50\% 50% ): kW/Ton C = 95 / 250 = 0.380 kW/Ton \text{kW/Ton}_C = 95 / 250 = 0.380\text{ kW/Ton} kW/Ton C ​ = 95/250 = 0.380 kW/Ton

Point D ( 25 % 25\% 25% ): kW/Ton D = 45 / 125 = 0.360 kW/Ton \text{kW/Ton}_D = 45 / 125 = 0.360\text{ kW/Ton} kW/Ton D ​ = 45/125 = 0.360 kW/Ton

AHRI IPLV Formula for kW/Ton \text{kW/Ton} kW/Ton (reciprocal harmonic weighting): IPLV kW/Ton = 1 0.010 A + 0.420 B + 0.450 C + 0.120 D \text{IPLV}_{\text{kW/Ton}} = \frac{1}{\frac{0.010}{A} + \frac{0.420}{B} + \frac{0.450}{C} + \frac{0.120}{D}} IPLV kW/Ton ​ = A 0.010 ​ + B 0.420 ​ + C 0.450 ​ + D 0.120 ​ 1 ​

  • 0.010 0.570 = 0.01754 \frac{0.010}{0.570} = 0.01754 0.570 0.010 ​ = 0.01754
  • 0.420 0.4667 = 0.89994 \frac{0.420}{0.4667} = 0.89994 0.4667 0.420 ​ = 0.89994
  • 0.450 0.380 = 1.18421 \frac{0.450}{0.380} = 1.18421 0.380 0.450 ​ = 1.18421
  • 0.120 0.360 = 0.33333 \frac{0.120}{0.360} = 0.33333 0.360 0.120 ​ = 0.33333

∑ = 0.01754 + 0.89994 + 1.18421 + 0.33333 = 2.43502 \sum = 0.01754 + 0.89994 + 1.18421 + 0.33333 = 2.43502 ∑ = 0.01754 + 0.89994 + 1.18421 + 0.33333 = 2.43502

IPLV kW/Ton = 1 2.43502 = 0.4107 kW/Ton \text{IPLV}_{\text{kW/Ton}} = \frac{1}{2.43502} = \mathbf{0.4107\text{ kW/Ton}} IPLV kW/Ton ​ = 2.43502 1 ​ = 0.4107 kW/Ton

3. Integrated Economizer Supplemental Cooling:

Economizer "Free" Sensible Cooling Capacity: Q ˙ econ = 1.08 × CFM × ( T oa − T supply ) = 1.08 × 10 , 000 × ( 60 − 52 ) = 86 , 400 Btu/h \dot{Q}_{\text{econ}} = 1.08 \times \text{CFM} \times (T_{\text{oa}} - T_{\text{supply}}) = 1.08 \times 10,000 \times (60 - 52) = 86,400\text{ Btu/h} Q ˙ ​ econ ​ = 1.08 × CFM × ( T oa ​ − T supply ​ ) = 1.08 × 10 , 000 × ( 60 − 52 ) = 86 , 400 Btu/h Tons econ = 86 , 400 Btu/h 12 , 000 Btu/(h ⋅ Ton) = 7.20 Tons \text{Tons}_{\text{econ}} = \frac{86,400\text{ Btu/h}}{12,000\text{ Btu/(h}\cdot\text{Ton)}} = 7.20\text{ Tons} Tons econ ​ = 12 , 000 Btu/(h ⋅ Ton) 86 , 400 Btu/h ​ = 7.20 Tons

Net Load Remaining on Chiller: Load chiller = 300 Tons − 7.20 Tons = 292.80 Tons \text{Load}_{\text{chiller}} = 300\text{ Tons} - 7.20\text{ Tons} = 292.80\text{ Tons} Load chiller ​ = 300 Tons − 7.20 Tons = 292.80 Tons

7. NCEES Reference Handbook Navigation Strategies

Efficiency Conversions: Look under HVAC & Refrigeration for kW/Ton = 12 / EER = 3.516 / COP \text{kW/Ton} = 12 / \text{EER} = 3.516 / \text{COP} kW/Ton = 12/ EER = 3.516/ COP .

Economizer High-Limit Table: Search "Economizer" or "High-Limit Shutoff" to check prohibited control types by climate zone.

Fan Power Limitations: Search "Fan System Power" to find the 0.0011 0.0011 0.0011 (CV) and 0.0015 0.0015 0.0015 (VAV) coefficients and pressure drop credit formulas.