Study guide
5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head
Key Takeaways Explain This Topic AI
Minor losses arise from flow separation, recirculating eddies, and turbulent dissipation caused by valves, fittings, bends, entrances, exits, and area transitions.
The loss coefficient method defines head loss as h_m = K * (V^2 / 2g); total system friction equals h_L = [f * (L/D) + sum(K)] * (V^2 / 2g).
The equivalent length method converts fitting resistance into an equivalent straight pipe length: L_eq = (K * D) / f_T, allowing total system length L_total = L_pipe + sum(L_eq).
Submerged pipe discharge into a reservoir always has an exit loss coefficient of K_exit = 1.0, because the entire kinetic velocity head (V^2 / 2g) is completely dissipated into turbulence.
In closed hydronic piping loops, static elevation head is zero (Delta_z = 0); in open hydronic systems (cooling towers, sumps), total pump head must include static elevation lift, nozzle discharge pressure, and all friction/minor losses.
Last updated: August 2026
5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head
In addition to continuous wall friction in straight pipe runs, piping systems experience localized pressure losses termed minor losses . Despite the name "minor," these losses frequently account for 30 % to 70 % 30\% \text{ to } 70\% 30% to 70% of the total system head in complex HVAC mechanical rooms packed with elbows, tees, isolation valves, check valves, strainers, control valves, and heat exchangers. Passing the PE Mechanical exam requires mastering both the Loss Coefficient ( K K K ) Method and the Equivalent Length ( L e q L_{eq} L e q ) Method , as well as synthesizing these components into the Total System Head Curve .
1. Physics of Minor Losses & The Loss Coefficient ( K K K )
Minor losses occur whenever fluid encounters changes in flow direction, cross-sectional flow area, or internal geometry. These disruptions cause flow separation from conduit boundaries, creating high-shear mixing layers, recirculating vortex wakes, and intense turbulent eddy dissipation. +-----------------------------------------------------------------------------+
- | FLOW SEPARATION & VORTEX SHEDDING IN A 90-DEGREE ELBOW |
- +-----------------------------------------------------------------------------+
- | Inner Radius Separation Zone (Vena Contracta) |
- | +-----+ |
- | | *** | <--- High Turbulent Eddy Dissipation |
- | ==============/ \======================= |
- | Fluid Flow Fluid Flow |
- | ===========\ /==================== |
- | +----------+ |
- | Outer Wall Impingement & Secondary Swirl Flow |
- +-----------------------------------------------------------------------------+
- The Loss Coefficient Formulation
Minor head loss ( h m h_m h m ) and minor pressure drop ( Δ P m \Delta P_m Δ P m ) are proportional to the dynamic velocity head ( V 2 / 2 g V^2 / 2g V 2 /2 g ) of the fluid passing through the fitting: h m = K V 2 2 g h_m = K \frac{V^2}{2g} h m = K 2 g V 2 Δ P m = K ρ V 2 2 g c \Delta P_m = K \frac{\rho V^2}{2 g_c} Δ P m = K 2 g c ρ V 2
Where:
- h m h_m h m : Minor head loss ( ft of fluid column \text{ft of fluid column} ft of fluid column )
- K K K : Dimensionless minor loss coefficient for the specific fitting or valve
- V V V : Average flow velocity in the conduit attached to the fitting ( ft/s \text{ft/s} ft/s )
- g g g : Gravitational acceleration ( 32.174 ft/s 2 32.174\text{ ft/s}^2 32.174 ft/s 2 )
- Combined Straight Pipe & Minor Loss Equation
When summing all straight pipe friction and localized fittings of uniform diameter D D D : h L , total = ∑ h f + ∑ h m = ( f L D + ∑ K ) V 2 2 g h_{L,\text{total}} = \sum h_f + \sum h_m = \left( f \frac{L}{D} + \sum K \right) \frac{V^2}{2g} h L , total = ∑ h f + ∑ h m = ( f D L + ∑ K ) 2 g V 2
2. Representative K K K -Factors for HVAC Valves & Fittings
Minor loss coefficients depend on internal valve design, seat geometry, and fitting curvature. The table below lists standard K K K -factors based on NCEES Reference Handbook and Crane Technical Paper No. 410 data.
Fitting / Component Description Nominal Loss Coeff. ( K K K ) Equivalent L / D L/D L / D ( K / f T K / f_T K / f T ) Engineering Notes & Design Characteristics
90 ∘ 90^\circ 9 0 ∘ Standard Threaded Elbow 0.75 − 0.90 0.75 - 0.90 0.75 − 0.90 30 30 30 Standard radius r / D = 1.0 r/D = 1.0 r / D = 1.0 ; high separation at inner throat
90 ∘ 90^\circ 9 0 ∘ Long Radius Flanged/Welded Elbow 0.35 − 0.45 0.35 - 0.45 0.35 − 0.45 16 − 20 16 - 20 16 − 20 Long radius r / D = 1.5 r/D = 1.5 r / D = 1.5 ; smooth curvature, preferred in HVAC
45 ∘ 45^\circ 4 5 ∘ Standard Elbow 0.35 − 0.40 0.35 - 0.40 0.35 − 0.40 16 16 16 Low deflection angle, lower dynamic pressure loss
Standard Tee (Flow-Through Run) 0.20 − 0.40 0.20 - 0.40 0.20 − 0.40 20 20 20 Flow passes straight through the main header
Standard Tee (Branch Flow 90 ∘ 90^\circ 9 0 ∘ ) 1.00 − 1.80 1.00 - 1.80 1.00 − 1.80 60 60 60 High loss due to 90 ∘ 90^\circ 9 0 ∘ turn and header splitting
Gate Valve (Fully Open) 0.15 − 0.20 0.15 - 0.20 0.15 − 0.20 8 8 8 Unobstructed full-bore flow path; very low resistance
Globe Valve (Fully Open) 6.00 − 10.0 6.00 - 10.0 6.00 − 10.0 340 340 340 S-shaped internal baffle forces two 90 ∘ 90^\circ 9 0 ∘ turns; extreme loss
Butterfly Valve (Fully Open) 0.50 − 1.00 0.50 - 1.00 0.50 − 1.00 45 45 45 Wafer disc remains in flow stream; moderate resistance
Ball Valve (Full Port, Fully Open) 0.05 − 0.10 0.05 - 0.10 0.05 − 0.10 3 3 3 True cylindrical bore; virtually zero loss
Swing Check Valve (Fully Open) 2.00 − 2.50 2.00 - 2.50 2.00 − 2.50 100 100 100 Hinged flapper held open by flow velocity
Y-Strainer (Clean Screen) 1.50 − 3.00 1.50 - 3.00 1.50 − 3.00 80 − 120 80 - 120 80 − 120 Wire mesh basket; dirty screens can exceed K > 10 K > 10 K > 10 +-----------------------------------------------------------------------------+
- | PIPE ENTRANCE & EXIT LOSS COEFFICIENTS |
- +-----------------------------------------------------------------------------+
- | ENTRANCES (Flow entering pipe from reservoir): |
- | |
- | Inward Projecting (Borda) Sharp-Edged (Square) Well-Rounded (Bell) |
- | ======+ ======+ =====\ |
- | | | \ |
- | | K = 0.80 - 1.0 | K = 0.50 | K = 0.04 |
- | | | / |
- | ======+ ======+ =====/ |
- | |
- | EXITS (Flow discharging into reservoir/tank): |
- | Submerged Pipe Exit (All geometries: square, rounded, angled): K_exit = 1.0|
- +-----------------------------------------------------------------------------+
Exam Trap — Submerged Exit Loss ( K exit = 1.0 K_{\text{exit}} = 1.0 K exit = 1.0 ): Regardless of whether a pipe exit is sharp, beveled, or bellmouthed, when a submerged pipe discharges into a large reservoir or tank, K exit = 1.0 K_{\text{exit}} = 1.0 K exit = 1.0 . The entire kinetic energy of the high-velocity jet ( V 2 / 2 g V^2 / 2g V 2 /2 g ) is fully dissipated into turbulent thermal eddies in the stationary reservoir liquid.
3. The Equivalent Length Method ( L e q L_{eq} L e q )
The Equivalent Length Method converts the pressure drop of each valve and fitting into an equivalent length of straight pipe that produces the exact same friction loss: L e q = K ⋅ D f T = ( L D ) equivalent ⋅ D L_{eq} = \frac{K \cdot D}{f_T} = \left( \frac{L}{D} \right)_{\text{equivalent}} \cdot D L e q = f T K ⋅ D = ( D L ) equivalent ⋅ D
Where:
L e q L_{eq} L e q : Equivalent length of straight pipe ( ft \text{ft} ft )
f T f_T f T : Fully turbulent Darcy friction factor for that pipe size (from Crane TP-410 / Moody diagram wholly turbulent regime)
( L / D ) equivalent (L/D)_{\text{equivalent}} ( L / D ) equivalent : Equivalent length-to-diameter ratio specified by manufacturer or handbook
Total System Effective Length L total = L pipe + ∑ L e q = L pipe + ∑ [ ( L D ) i ⋅ D ] L_{\text{total}} = L_{\text{pipe}} + \sum L_{eq} = L_{\text{pipe}} + \sum \left[ \left(\frac{L}{D}\right)_i \cdot D \right] L total = L pipe + ∑ L e q = L pipe + ∑ [ ( D L ) i ⋅ D ] h L , total = f L total D V 2 2 g h_{L,\text{total}} = f \frac{L_{\text{total}}}{D} \frac{V^2}{2g} h L , total = f D L total 2 g V 2
4. Closed-Loop vs. Open-Loop Total System Head
Evaluating the required pump head on the PE exam requires identifying whether the hydronic architecture is a closed-loop or open-loop configuration. +-----------------------------------------------------------------------------------------+
- | CLOSED-LOOP VS. OPEN-LOOP HYDRONIC SYSTEM ARCHITECTURE |
- +-----------------------------------------------------------------------------------------+
- | CLOSED LOOP (Chilled Water, Closed Heating): |
- | - Complete continuous piping circuit sealed from atmosphere |
- | - Fluid elevation rises are matched by equal elevation falls: Delta_z_static = 0 |
- | - Static pressure at pump suction equals expansion tank setpoint |
- | - Total Pump Head is 100% Dynamic Friction: H_sys = C * Q^2 |
- | |
- | OPEN LOOP (Cooling Tower Condenser Water, Sump Drainage): |
- | - Open to atmosphere at cooling tower basin and spray distribution nozzles |
- | - Net Static Elevation Lift: Delta_z_static = z_nozzle - z_basin > 0 |
- | - Nozzle Operating Pressure Head: P_nozzle / gamma (typically 3 to 5 psig = 7-12 ft) |
- | - Total Pump Head = Static Lift + Nozzle Head + Friction Losses: |
- | H_sys = Delta_z_static + (P_nozzle / gamma) + C * Q^2 |
- +-----------------------------------------------------------------------------------------+
General System Head Equation H sys = H static + H dynamic H_{\text{sys}} = H_{\text{static}} + H_{\text{dynamic}} H sys = H static + H dynamic H sys = [ ( z 2 − z 1 ) + P 2 − P 1 γ ] ⏟ H static + [ f L D + ∑ K + Δ P coils γ + Δ P valves γ ] V 2 2 g ⏟ H dynamic = C sys Q 2 H_{\text{sys}} = \underbrace{\left[ (z_2 - z_1) + \frac{P_2 - P_1}{\gamma} \right]}_{H_{\text{static}}} + \underbrace{\left[ f \frac{L}{D} + \sum K + \frac{\Delta P_{\text{coils}}}{\gamma} + \frac{\Delta P_{\text{valves}}}{\gamma} \right] \frac{V^2}{2g}}_{H_{\text{dynamic}} = C_{\text{sys}} Q^2} H sys = H static [ ( z 2 − z 1 ) + γ P 2 − P 1 ] + H dynamic = C sys Q 2 [ f D L + ∑ K + γ Δ P coils + γ Δ P valves ] 2 g V 2 Head (ft)
- ^
- | / System Curve: H_sys = H_static + C * Q^2
- | /
- | /
- | /
- | /
- |-----------------------------/ <--- Operating Point (Pump H = Sys H)
- | /
- | /
- | /
- +-------------------------+
- | H_static
- | (Open Loop Lift + P_noz)
- +---------------------------------------------> Flow Rate Q (GPM)
- 5. Worked Engineering Examples
- Worked Example 1: Closed-Loop Chilled Water Total Head Calculation
A primary chilled water pumping loop circulates Q = 220 GPM Q = 220\text{ GPM} Q = 220 GPM through a closed piping network consisting of 400 ft 400\text{ ft} 400 ft of 4-inch Schedule 40 steel pipe ( D = 4.026 in. = 0.3355 ft D = 4.026\text{ in.} = 0.3355\text{ ft} D = 4.026 in. = 0.3355 ft , f = 0.020 f = 0.020 f = 0.020 ). The loop supplies an Air Handling Unit (AHU) located on the 4th floor ( 50 ft 50\text{ ft} 50 ft above the basement chiller plant). The piping contains the following fittings:
- 12 × 90 ∘ 12 \times 90^\circ 12 × 9 0 ∘ standard elbows ( K = 0.60 K = 0.60 K = 0.60 each)
- 4 × 4 \times 4 × isolation butterfly valves ( K = 0.50 K = 0.50 K = 0.50 each)
- 1 × 1 \times 1 × check valve ( K = 2.00 K = 2.00 K = 2.00 )
1 × 1 \times 1 × chiller evaporator bundle ( Δ P evap = 18.0 ft of water \Delta P_{\text{evap}} = 18.0\text{ ft of water} Δ P evap = 18.0 ft of water )
1 × 1 \times 1 × AHU cooling coil ( Δ P coil = 14.0 ft of water \Delta P_{\text{coil}} = 14.0\text{ ft of water} Δ P coil = 14.0 ft of water )
1 × 1 \times 1 × modulating 2-way control valve ( Δ P valve = 5.0 psi \Delta P_{\text{valve}} = 5.0\text{ psi} Δ P valve = 5.0 psi )
Calculate the total pump head ( H pump H_{\text{pump}} H pump ) required at design flow. Given:
- Flow: Q = 220 GPM (0.4902 ft3/s)
- Pipe: 4" Sch 40 (D = 0.3355 ft, Area = 0.08841 ft2, L = 400 ft, f = 0.020)
- Elevation rise to 4th floor = 50 ft (Closed hydronic loop)
- Equipment pressure drops: Evap = 18.0 ft, Coil = 14.0 ft, Valve = 5.0 psi
Step 1: Calculate flow velocity and velocity head: V = Q A = 0.4902 ft 3 / s 0.08841 ft 2 = 5.545 ft/s V = \frac{Q}{A} = \frac{0.4902\text{ ft}^3/\text{s}}{0.08841\text{ ft}^2} = 5.545\text{ ft/s} V = A Q = 0.08841 ft 2 0.4902 ft 3 / s = 5.545 ft/s V 2 2 g = ( 5.545 ft/s ) 2 2 × 32.174 ft/s 2 = 30.747 64.348 = 0.4778 ft \frac{V^2}{2g} = \frac{(5.545\text{ ft/s})^2}{2 \times 32.174\text{ ft/s}^2} = \frac{30.747}{64.348} = 0.4778\text{ ft} 2 g V 2 = 2 × 32.174 ft/s 2 ( 5.545 ft/s ) 2 = 64.348 30.747 = 0.4778 ft
Step 2: Calculate straight pipe friction loss ( h f h_f h f ): h f = f L D V 2 2 g = 0.020 × ( 400 ft 0.3355 ft ) × 0.4778 ft = 0.020 × 1192.25 × 0.4778 = 11.39 ft h_f = f \frac{L}{D} \frac{V^2}{2g} = 0.020 \times \left( \frac{400\text{ ft}}{0.3355\text{ ft}} \right) \times 0.4778\text{ ft} = 0.020 \times 1192.25 \times 0.4778 = 11.39\text{ ft} h f = f D L 2 g V 2 = 0.020 × ( 0.3355 ft 400 ft ) × 0.4778 ft = 0.020 × 1192.25 × 0.4778 = 11.39 ft
Step 3: Sum fitting loss coefficients and calculate minor losses ( h m h_m h m ): ∑ K = 12 ( 0.60 ) + 4 ( 0.50 ) + 1 ( 2.00 ) = 7.20 + 2.00 + 2.00 = 11.20 \sum K = 12(0.60) + 4(0.50) + 1(2.00) = 7.20 + 2.00 + 2.00 = 11.20 ∑ K = 12 ( 0.60 ) + 4 ( 0.50 ) + 1 ( 2.00 ) = 7.20 + 2.00 + 2.00 = 11.20 h m = ∑ K V 2 2 g = 11.20 × 0.4778 ft = 5.35 ft h_m = \sum K \frac{V^2}{2g} = 11.20 \times 0.4778\text{ ft} = 5.35\text{ ft} h m = ∑ K 2 g V 2 = 11.20 × 0.4778 ft = 5.35 ft
Step 4: Convert control valve pressure drop to feet of water: h valve = 5.0 psi × 2.3087 ft/psi = 11.54 ft h_{\text{valve}} = 5.0\text{ psi} \times 2.3087\text{ ft/psi} = 11.54\text{ ft} h valve = 5.0 psi × 2.3087 ft/psi = 11.54 ft
Step 5: Synthesize total closed-loop system head: In a closed loop, the 50 ft 50\text{ ft} 50 ft elevation rise to the 4th floor is completely balanced by the 50 ft 50\text{ ft} 50 ft gravitational drop on the return riser ( Δ z static = 0 \Delta z_{\text{static}} = 0 Δ z static = 0 ). H pump = h f + h m + h valve + Δ P coil + Δ P evap H_{\text{pump}} = h_f + h_m + h_{\text{valve}} + \Delta P_{\text{coil}} + \Delta P_{\text{evap}} H pump = h f + h m + h valve + Δ P coil + Δ P evap H pump = 11.39 ft + 5.35 ft + 11.54 ft + 14.00 ft + 18.00 ft = 60.28 ft ≈ 60.3 ft H_{\text{pump}} = 11.39\text{ ft} + 5.35\text{ ft} + 11.54\text{ ft} + 14.00\text{ ft} + 18.00\text{ ft} = 60.28\text{ ft} \approx 60.3\text{ ft} H pump = 11.39 ft + 5.35 ft + 11.54 ft + 14.00 ft + 18.00 ft = 60.28 ft ≈ 60.3 ft
Worked Example 2: Open-Loop Cooling Tower Total System Head
A condenser water pump circulates Q = 600 GPM Q = 600\text{ GPM} Q = 600 GPM from a cooling tower basin (elevation 0 ft 0\text{ ft} 0 ft ) through a chiller condenser and discharges via spray nozzles at the top of the tower (elevation + 22 ft +22\text{ ft} + 22 ft ). System parameters:
Pipe: 150 ft 150\text{ ft} 150 ft of 6-inch Schedule 40 steel ( D = 6.065 in. = 0.5054 ft D = 6.065\text{ in.} = 0.5054\text{ ft} D = 6.065 in. = 0.5054 ft , f = 0.018 f = 0.018 f = 0.018 , V = 6.67 ft/s V = 6.67\text{ ft/s} V = 6.67 ft/s , V 2 / 2 g = 0.691 ft V^2/2g = 0.691\text{ ft} V 2 /2 g = 0.691 ft )
Fitting minor loss sum: ∑ K = 5.8 \sum K = 5.8 ∑ K = 5.8
Water-cooled chiller condenser pressure drop: Δ P cond = 11.5 psi \Delta P_{\text{cond}} = 11.5\text{ psi} Δ P cond = 11.5 psi
Cooling tower spray nozzle required pressure: P nozzle = 4.5 psig P_{\text{nozzle}} = 4.5\text{ psig} P nozzle = 4.5 psig
Calculate the total pump head required.
Step 1: Calculate static elevation lift and nozzle pressure head: H static = Δ z = 22.0 ft − 0 ft = 22.0 ft H_{\text{static}} = \Delta z = 22.0\text{ ft} - 0\text{ ft} = 22.0\text{ ft} H static = Δ z = 22.0 ft − 0 ft = 22.0 ft H nozzle = 4.5 psi × 2.3087 ft/psi = 10.39 ft H_{\text{nozzle}} = 4.5\text{ psi} \times 2.3087\text{ ft/psi} = 10.39\text{ ft} H nozzle = 4.5 psi × 2.3087 ft/psi = 10.39 ft
Step 2: Calculate pipe friction and fitting minor losses: h f = 0.018 × ( 150 ft 0.5054 ft ) × 0.691 ft = 0.018 × 296.8 × 0.691 = 3.69 ft h_f = 0.018 \times \left( \frac{150\text{ ft}}{0.5054\text{ ft}} \right) \times 0.691\text{ ft} = 0.018 \times 296.8 \times 0.691 = 3.69\text{ ft} h f = 0.018 × ( 0.5054 ft 150 ft ) × 0.691 ft = 0.018 × 296.8 × 0.691 = 3.69 ft h m = ∑ K V 2 2 g = 5.8 × 0.691 ft = 4.01 ft h_m = \sum K \frac{V^2}{2g} = 5.8 \times 0.691\text{ ft} = 4.01\text{ ft} h m = ∑ K 2 g V 2 = 5.8 × 0.691 ft = 4.01 ft
Step 3: Calculate chiller condenser head drop: H cond = 11.5 psi × 2.3087 ft/psi = 26.55 ft H_{\text{cond}} = 11.5\text{ psi} \times 2.3087\text{ ft/psi} = 26.55\text{ ft} H cond = 11.5 psi × 2.3087 ft/psi = 26.55 ft
Step 4: Sum all open-loop head components: H pump = H static + H nozzle + h f + h m + H cond H_{\text{pump}} = H_{\text{static}} + H_{\text{nozzle}} + h_f + h_m + H_{\text{cond}} H pump = H static + H nozzle + h f + h m + H cond H pump = 22.0 ft + 10.39 ft + 3.69 ft + 4.01 ft + 26.55 ft = 66.64 ft ≈ 66.6 ft H_{\text{pump}} = 22.0\text{ ft} + 10.39\text{ ft} + 3.69\text{ ft} + 4.01\text{ ft} + 26.55\text{ ft} = 66.64\text{ ft} \approx 66.6\text{ ft} H pump = 22.0 ft + 10.39 ft + 3.69 ft + 4.01 ft + 26.55 ft = 66.64 ft ≈ 66.6 ft
6. NCEES Reference Handbook Navigation & Exam Tips
Minor Loss Tables: In the Reference Handbook, look under Fluid Mechanics → \rightarrow → Minor Losses / Equivalent Lengths for K K K -factor values and L / D L/D L / D ratios.
Static Head Trap: Never add vertical floor elevation differences when calculating pump head for closed chilled water or heating hot water loops. Elevation lift is ONLY added for open systems where the fluid is lifted across an unsealed air gap (such as cooling towers or open sump discharge).