Study guide

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor)

PE Mechanical: HVAC and Refrigeration Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations

1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)

2 Chapter 2: Thermodynamics & Energy Balances

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment

3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment

3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes

4 Chapter 4: Heat Transfer Principles & Sizing

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)

5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals

5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves

6 Chapter 6: Heating & Cooling Load Calculations

6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis

7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design

8 Chapter 8: Refrigerants, Environmental Regulations & Safety

8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers

9 Chapter 9: HVAC Equipment & Primary Machinery

9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems

10 Chapter 10: Air-Side Systems & Distribution

10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection

11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant

11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems

12 Chapter 12: HVAC Control Concepts, Sensors & Sequences

12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences

13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes

13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops

14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations

14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor)

Key Takeaways Explain This Topic AI

Fourier's Law governs steady-state conduction in planar geometries: q ˙ = − k A d T d x = k A Δ T L = Δ T R t h \dot{q} = -k A \frac{dT}{dx} = \frac{k A \Delta T}{L} = \frac{\Delta T}{R_{th}} q ˙ ​ = − k A d x d T ​ = L k A Δ T ​ = R t h ​ Δ T ​ , where thermal conductivity k k k is expressed in Btu/(hr ⋅ ft ⋅ ∘ F) \text{Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)} Btu/(hr ⋅ ft ⋅ ∘ F) or W/(m ⋅ K) \text{W/(m}\cdot\text{K)} W/(m ⋅ K) .

Thermal resistance for a flat layer is R = L k R = \frac{L}{k} R = k L ​ in hr ⋅ ft 2 ⋅ ∘ F/Btu \text{hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu} hr ⋅ ft 2 ⋅ ∘ F/Btu ; total thermal resistance for series layers sums linearly: R t o t a l = R i + ∑ L j k j + R o R_{total} = R_i + \sum \frac{L_j}{k_j} + R_o R t o t a l ​ = R i ​ + ∑ k j ​ L j ​ ​ + R o ​ , and the overall U-factor is U = 1 R t o t a l U = \frac{1}{R_{total}} U = R t o t a l ​ 1 ​ .

In parallel heat flow paths (such as wood or steel-framed building assemblies), overall U-factor is area-weighted: U o v e r a l l = ∑ f j U j U_{overall} = \sum f_j U_j U o v er a ll ​ = ∑ f j ​ U j ​ , where f j f_j f j ​ is the area fraction of each path.

Radial conduction through cylindrical walls (pipes, tubes, ductwork) exhibits logarithmic thermal resistance per unit length: R c y l ′ = ln ⁡ ( r o / r i ) 2 π k R'_{cyl} = \frac{\ln(r_o/r_i)}{2 \pi k} R cy l ′ ​ = 2 πk l n ( r o ​ / r i ​ ) ​ , leading to heat transfer q ˙ ′ = 2 π k ( T i − T o ) ln ⁡ ( r o / r i ) \dot{q}' = \frac{2 \pi k (T_i - T_o)}{\ln(r_o/r_i)} q ˙ ​ ′ = l n ( r o ​ / r i ​ ) 2 πk ( T i ​ − T o ​ ) ​ .

The critical radius of insulation for a cylinder is r c r = k i n s h o r_{cr} = \frac{k_{ins}}{h_o} r cr ​ = h o ​ k in s ​ ​ ; adding insulation to an outer radius r o < r c r r_o < r_{cr} r o ​ < r cr ​ increases total heat transfer until r o = r c r r_o = r_{cr} r o ​ = r cr ​ , after which further insulation decreases heat loss.

Last updated: August 2026

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor)

Thermal conduction is the transfer of internal thermal energy through microscopic collisions of particles and movement of free electrons within a stationary medium. In HVAC and refrigeration engineering, conduction governs envelope transmission loads (walls, roofs, fenestration, floor slabs), thermal insulation performance, pipe and duct heat gains/losses, and solid-wall thermal barriers in heat exchangers. Analyzing these systems requires evaluating one-dimensional steady-state conduction through planar and radial multi-layered geometries using the thermal resistance network methodology.

1. Fourier's Law of Conduction & Planar Heat Flow

Conduction is governed by Fourier's Law , which states that the local heat flux is directly proportional to the negative temperature gradient along the direction of heat flow: q ′ ′ = q ˙ A = − k d T d x q'' = \frac{\dot{q}}{A} = -k \frac{dT}{dx} q ′′ = A q ˙ ​ ​ = − k d x d T ​

Where:

q ˙ = heat transfer rate ( Btu/hr or W ) \dot{q} = \text{heat transfer rate } (\text{Btu/hr or W}) q ˙ ​ = heat transfer rate ( Btu/hr or W )

q ′ ′ = heat flux ( Btu/(hr ⋅ ft 2 ) or W/m 2 ) q'' = \text{heat flux } (\text{Btu/(hr}\cdot\text{ft}^2) \text{ or W/m}^2) q ′′ = heat flux ( Btu/(hr ⋅ ft 2 ) or W/m 2 )

A = cross-sectional area normal to heat flow ( ft 2 or m 2 ) A = \text{cross-sectional area normal to heat flow } (\text{ft}^2 \text{ or m}^2) A = cross-sectional area normal to heat flow ( ft 2 or m 2 )

k = thermal conductivity of the material ( Btu/(hr ⋅ ft ⋅ ∘ F) or W/(m ⋅ K) ) k = \text{thermal conductivity of the material } (\text{Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)} \text{ or W/(m}\cdot\text{K)}) k = thermal conductivity of the material ( Btu/(hr ⋅ ft ⋅ ∘ F) or W/(m ⋅ K) )

d T d x = temperature gradient in the direction of heat flow ( ∘ F/ft or ∘ C/m ) \frac{dT}{dx} = \text{temperature gradient in the direction of heat flow } ({}^\circ\text{F/ft or } {}^\circ\text{C/m}) d x d T ​ = temperature gradient in the direction of heat flow ( ∘ F/ft or ∘ C/m ) +-----------------------------------------------------------------------------------------+

  • | ONE-DIMENSIONAL STEADY-STATE CONDUCTION THROUGH A PLANE SLAB |
  • +-----------------------------------------------------------------------------------------+
  • | T_1 (Hot Surface) |
  • | |=========================| |
  • | | | ---> Heat Flow: q_dot = k * A * (T_1 - T_2) / L |
  • | | Material Thickness L | |
  • | | Conductivity: k | ---> Thermal Resistance: R_th = L / (k * A) |
  • | | | |
  • | |=========================| |
  • | T_2 (Cold Surface) |
  • +-----------------------------------------------------------------------------------------+

Integrating Fourier's law for a homogeneous planar slab of uniform thickness L L L with fixed surface temperatures T 1 T_1 T 1 ​ and T 2 T_2 T 2 ​ ( T 1 > T 2 T_1 > T_2 T 1 ​ > T 2 ​ ) under steady-state conditions with constant thermal conductivity: q ˙ = k A ( T 1 − T 2 ) L = T 1 − T 2 R t h \dot{q} = \frac{k A (T_1 - T_2)}{L} = \frac{T_1 - T_2}{R_{th}} q ˙ ​ = L k A ( T 1 ​ − T 2 ​ ) ​ = R t h ​ T 1 ​ − T 2 ​ ​

Thermal Resistance ( R t h R_{th} R t h ​ ) and Unit Thermal Resistance ( R R R -Value)

In mechanical engineering, the electrical-thermal analogy represents temperature difference Δ T \Delta T Δ T as voltage potential, heat rate q ˙ \dot{q} q ˙ ​ as electric current, and thermal resistance R t h R_{th} R t h ​ as electrical resistance: R t h = L k A [ hr ⋅ ∘ F Btu or K W ] R_{th} = \frac{L}{k A} \quad \left[\frac{\text{hr}\cdot{}^\circ\text{F}}{\text{Btu}} \text{ or } \frac{\text{K}}{\text{W}}\right] R t h ​ = k A L ​ [ Btu hr ⋅ ∘ F ​ or W K ​ ]

In building envelope and architectural engineering, resistance is normalized per unit area and termed the R R R -value ( R R R ): R = R t h × A = L k = L ⋅ r [ hr ⋅ ft 2 ⋅ ∘ F Btu ] R = R_{th} \times A = \frac{L}{k} = L \cdot r \quad \left[\frac{\text{hr}\cdot\text{ft}^2\cdot{}^\circ\text{F}}{\text{Btu}}\right] R = R t h ​ × A = k L ​ = L ⋅ r [ Btu hr ⋅ ft 2 ⋅ ∘ F ​ ]

Where r = 1 / k r = 1/k r = 1/ k is the thermal resistivity per unit thickness (expressed in hr ⋅ ft ⋅ ∘ F/Btu \text{hr}\cdot\text{ft}\cdot{}^\circ\text{F/Btu} hr ⋅ ft ⋅ ∘ F/Btu or commonly as R R R -value per inch: hr ⋅ ft 2 ⋅ ∘ F/(Btu ⋅ in.) \text{hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/(Btu}\cdot\text{in.)} hr ⋅ ft 2 ⋅ ∘ F/(Btu ⋅ in.) ). When thickness L i n L_{in} L in ​ is in inches and thermal conductivity k k k is in Btu/(hr ⋅ ft ⋅ ∘ F) \text{Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)} Btu/(hr ⋅ ft ⋅ ∘ F) : R = L i n / 12 k = L i n 12 k R = \frac{L_{in} / 12}{k} = \frac{L_{in}}{12 k} R = k L in ​ /12 ​ = 12 k L in ​ ​

2. Multilayer Planar Assemblies & Overall Heat Transmission ( U U U -Factor)

Building envelopes and duct/pipe insulation assemblies consist of multiple material layers in series, bounded by interior and exterior air boundary layers (convection/radiation air films). +-----------------------------------------------------------------------------------------+

  • | SERIES THERMAL RESISTANCE NETWORK (BUILDING ENVELOPE) |
  • +-----------------------------------------------------------------------------------------+
  • | T_inside o---[ R_i ]---o---[ R_1 ]---o---[ R_2 ]---o---[ R_3 ]---o---[ R_o ]---o T_outside
  • | Air Film Gypsum Insulation Sheathing Air Film |
  • | |
  • | Total Resistance: R_total = R_i + R_1 + R_2 + R_3 + R_o |
  • | Overall Heat Transmission Coefficient: U = 1 / R_total |
  • +-----------------------------------------------------------------------------------------+
  • Series Thermal Resistance Summation

For n n n plane layers in series bounded by fluid environments with internal convective film coefficient h i h_i h i ​ and external film coefficient h o h_o h o ​ : R t o t a l = R i + ∑ j = 1 n R j + R o = 1 h i + ∑ j = 1 n L j k j + 1 h o R_{total} = R_i + \sum_{j=1}^n R_j + R_o = \frac{1}{h_i} + \sum_{j=1}^n \frac{L_j}{k_j} + \frac{1}{h_o} R t o t a l ​ = R i ​ + j = 1 ∑ n ​ R j ​ + R o ​ = h i ​ 1 ​ + j = 1 ∑ n ​ k j ​ L j ​ ​ + h o ​ 1 ​

Where:

R i = 1 h i = inside surface air film resistance ( hr ⋅ ft 2 ⋅ ∘ F/Btu ) R_i = \frac{1}{h_i} = \text{inside surface air film resistance } (\text{hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu}) R i ​ = h i ​ 1 ​ = inside surface air film resistance ( hr ⋅ ft 2 ⋅ ∘ F/Btu )

R o = 1 h o = outside surface air film resistance ( hr ⋅ ft 2 ⋅ ∘ F/Btu ) R_o = \frac{1}{h_o} = \text{outside surface air film resistance } (\text{hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu}) R o ​ = h o ​ 1 ​ = outside surface air film resistance ( hr ⋅ ft 2 ⋅ ∘ F/Btu )

L j = thickness of layer j ( ft ) L_j = \text{thickness of layer } j\text{ } (\text{ft}) L j ​ = thickness of layer j ( ft )

k j = thermal conductivity of layer j ( Btu/(hr ⋅ ft ⋅ ∘ F) ) k_j = \text{thermal conductivity of layer } j\text{ } (\text{Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)}) k j ​ = thermal conductivity of layer j ( Btu/(hr ⋅ ft ⋅ ∘ F) )

Overall Heat Transmission Coefficient ( U U U -Factor)

The overall heat transfer coefficient U U U is the mathematical inverse of the total area-normalized thermal resistance: U = 1 R t o t a l = 1 R i + ∑ L j k j + R o [ Btu hr ⋅ ft 2 ⋅ ∘ F ] U = \frac{1}{R_{total}} = \frac{1}{R_i + \sum \frac{L_j}{k_j} + R_o} \quad \left[\frac{\text{Btu}}{\text{hr}\cdot\text{ft}^2\cdot{}^\circ\text{F}}\right] U = R t o t a l ​ 1 ​ = R i ​ + ∑ k j ​ L j ​ ​ + R o ​ 1 ​ [ hr ⋅ ft 2 ⋅ ∘ F Btu ​ ]

The steady-state heat transmission through an assembly of gross surface area A A A exposed to interior air temperature T i n T_{in} T in ​ and exterior air temperature T o u t T_{out} T o u t ​ is: q ˙ = U A ( T i n − T o u t ) = A ( T i n − T o u t ) R t o t a l \dot{q} = U A (T_{in} - T_{out}) = \frac{A (T_{in} - T_{out})}{R_{total}} q ˙ ​ = U A ( T in ​ − T o u t ​ ) = R t o t a l ​ A ( T in ​ − T o u t ​ ) ​

Interface Temperature Derivation

Under steady-state conditions, the heat flux q ′ ′ = q ˙ / A q'' = \dot{q}/A q ′′ = q ˙ ​ / A is constant through every consecutive layer in a series network. The temperature at any internal interface x x x between layer m m m and layer m + 1 m+1 m + 1 is determined from: q ′ ′ = T i n − T x R i n → x = T x − T o u t R x → o u t = T i n − T o u t R t o t a l q'' = \frac{T_{in} - T_x}{R_{in \to x}} = \frac{T_x - T_{out}}{R_{x \to out}} = \frac{T_{in} - T_{out}}{R_{total}} q ′′ = R in → x ​ T in ​ − T x ​ ​ = R x → o u t ​ T x ​ − T o u t ​ ​ = R t o t a l ​ T in ​ − T o u t ​ ​ T x = T i n − q ′ ′ ⋅ R i n → x = T i n − ( T i n − T o u t ) ( R i n → x R t o t a l ) T_x = T_{in} - q'' \cdot R_{in \to x} = T_{in} - (T_{in} - T_{out}) \left(\frac{R_{in \to x}}{R_{total}}\right) T x ​ = T in ​ − q ′′ ⋅ R in → x ​ = T in ​ − ( T in ​ − T o u t ​ ) ( R t o t a l ​ R in → x ​ ​ )

3. Parallel Paths, Framing Factors & Thermal Bridging

Real-world wall and roof assemblies are non-homogeneous because structural framing members (wood studs, light-gauge steel studs, concrete columns) penetrate the insulation cavity, creating parallel heat flow paths with differing thermal resistances. +-----------------------------------------------------------------------------------------+

  • | PARALLEL HEAT CONDUCTION THROUGH FRAMED WALL CAVITY |
  • +-----------------------------------------------------------------------------------------+
  • | Path A (Stud Path, f_frame = 15-25%): |
  • | T_in o---[ R_i ]---[ R_gyp ]---[ R_stud ]---[ R_sheath ]---[ R_clad ]---[ R_o ]---o T_out
  • | |
  • | Path B (Cavity Path, f_cav = 75-85%): |
  • | T_in o---[ R_i ]---[ R_gyp ]---[ R_insul ]---[ R_sheath ]---[ R_clad ]---[ R_o ]---o T_out
  • | |
  • | Overall Area-Weighted U-Factor: U_overall = (f_frame * U_stud) + (f_cav * U_cav) |
  • +-----------------------------------------------------------------------------------------+
  • ASHRAE Parallel Path Method (Wood-Framed Assemblies)

For assemblies with materials of moderate thermal conductivity (such as wood studs where k w o o d ≈ 0.08 Btu/(hr ⋅ ft ⋅ ∘ F) k_{wood} \approx 0.08\text{ Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)} k w oo d ​ ≈ 0.08 Btu/(hr ⋅ ft ⋅ ∘ F) ), heat flows predominantly perpendicular to the wall surface. The area-weighted overall U U U -factor is: U o v e r a l l = f f r a m e U f r a m e + f c a v i t y U c a v i t y = f f r a m e ( 1 R f r a m e , t o t a l ) + ( 1 − f f r a m e ) ( 1 R c a v i t y , t o t a l ) U_{overall} = f_{frame} U_{frame} + f_{cavity} U_{cavity} = f_{frame} \left(\frac{1}{R_{frame,total}}\right) + (1 - f_{frame}) \left(\frac{1}{R_{cavity,total}}\right) U o v er a ll ​ = f f r am e ​ U f r am e ​ + f c a v i t y ​ U c a v i t y ​ = f f r am e ​ ( R f r am e , t o t a l ​ 1 ​ ) + ( 1 − f f r am e ​ ) ( R c a v i t y , t o t a l ​ 1 ​ )

Where:

f f r a m e = framing factor (fraction of wall area occupied by framing, typically 0.15 to 0.25 ) f_{frame} = \text{framing factor (fraction of wall area occupied by framing, typically } 0.15\text{ to }0.25) f f r am e ​ = framing factor (fraction of wall area occupied by framing, typically 0.15 to 0.25 )

f c a v i t y = 1 − f f r a m e = cavity area fraction occupied by insulation f_{cavity} = 1 - f_{frame} = \text{cavity area fraction occupied by insulation} f c a v i t y ​ = 1 − f f r am e ​ = cavity area fraction occupied by insulation

R f r a m e , t o t a l = total series resistance along the stud/framing path R_{frame,total} = \text{total series resistance along the stud/framing path} R f r am e , t o t a l ​ = total series resistance along the stud/framing path

R c a v i t y , t o t a l = total series resistance along the insulated cavity path R_{cavity,total} = \text{total series resistance along the insulated cavity path} R c a v i t y , t o t a l ​ = total series resistance along the insulated cavity path

Effective Resistance of Parallel Assemblies

The effective assembly R R R -value ( R e f f R_{eff} R e ff ​ ) is the reciprocal of the area-weighted U U U -factor: R e f f = 1 U o v e r a l l = 1 f f r a m e U f r a m e + ( 1 − f f r a m e ) U c a v i t y R_{eff} = \frac{1}{U_{overall}} = \frac{1}{f_{frame} U_{frame} + (1 - f_{frame}) U_{cavity}} R e ff ​ = U o v er a ll ​ 1 ​ = f f r am e ​ U f r am e ​ + ( 1 − f f r am e ​ ) U c a v i t y ​ 1 ​

Critical Exam Rule — Never Average R R R -Values Directly: Thermal resistances in parallel cannot be averaged linearly. Always convert each parallel path to its individual U U U -factor ( U = 1 / R U = 1/R U = 1/ R ), calculate the area-weighted average U o v e r a l l U_{overall} U o v er a ll ​ , and take the reciprocal to find R e f f R_{eff} R e ff ​ . Direct averaging of R R R -values overestimates thermal performance by up to 40%.

Metal Framing & Thermal Bridging (ASHRAE Zone / Modified Zone Method)

Because structural steel has an extremely high thermal conductivity ( k s t e e l ≈ 26 − 30 Btu/(hr ⋅ ft ⋅ ∘ F) k_{steel} \approx 26-30\text{ Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)} k s t ee l ​ ≈ 26 − 30 Btu/(hr ⋅ ft ⋅ ∘ F) vs k f i b e r g l a s s ≈ 0.025 Btu/(hr ⋅ ft ⋅ ∘ F) k_{fiberglass} \approx 0.025\text{ Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)} k f ib er g l a ss ​ ≈ 0.025 Btu/(hr ⋅ ft ⋅ ∘ F) , a ratio greater than 1,000:1), light-gauge steel studs create severe two-dimensional thermal bridges that short-circuit cavity insulation. Standard R-13 or R-19 fiberglass cavity insulation between steel studs at 16 inches on center delivers an effective cavity performance of only R-6.0 to R-7.1. ASHRAE Standard 90.1 mandates the use of continuous exterior insulation ( c . i . c.i. c . i . ) on steel-framed walls to mitigate thermal bridging.

Loading diagram... Thermal Bridging vs Continuous Insulation Flux Distribution

4. Radial Conduction: Cylindrical & Spherical Geometries

In piping, chilled water lines, steam headers, and cylindrical ducts, the cross-sectional area normal to heat flow varies continuously with radius ( A ( r ) = 2 π r L A(r) = 2 \pi r L A ( r ) = 2 π r L ). +-----------------------------------------------------------------------------------------+

  • | RADIAL STEADY-STATE CONDUCTION IN A HOLLOW CYLINDER (PIPE WITH INSULATION) |
  • +-----------------------------------------------------------------------------------------+
  • | Outer Surface: Radius r_o, Temp T_o |
  • | /---------------------------------\ |
  • | / Insulation Layer (k_ins) \ |
  • | | /-------------------\ | |
  • | | / Pipe Wall (k_p) \ | |
  • | | | /------------\ | | |
  • | | | / Fluid T_i \ | | |
  • | | | | Inner Radius: | | | |
  • | | | | r_i | | | |
  • | | | \ / | | |
  • | | | \------------/ | | |
  • | | \ / | |
  • | | \-------------------/ | |
  • | \ / |
  • | \---------------------------------/ |
  • +-----------------------------------------------------------------------------------------+
  • Cylindrical Conduction Equation Derivation

Applying Fourier's Law at radius r r r for a cylinder of axial length L L L : q ˙ = − k A ( r ) d T d r = − k ( 2 π r L ) d T d r \dot{q} = -k A(r) \frac{dT}{dr} = -k (2 \pi r L) \frac{dT}{dr} q ˙ ​ = − k A ( r ) d r d T ​ = − k ( 2 π r L ) d r d T ​

Separating variables and integrating from inner radius r i r_i r i ​ (at T i T_i T i ​ ) to outer radius r o r_o r o ​ (at T o T_o T o ​ ): q ˙ ∫ r i r o d r r = − 2 π k L ∫ T i T o d T ⟹ q ˙ ln ⁡ ( r o r i ) = 2 π k L ( T i − T o ) \dot{q} \int_{r_i}^{r_o} \frac{dr}{r} = -2 \pi k L \int_{T_i}^{T_o} dT \implies \dot{q} \ln\left(\frac{r_o}{r_i}\right) = 2 \pi k L (T_i - T_o) q ˙ ​ ∫ r i ​ r o ​ ​ r d r ​ = − 2 πk L ∫ T i ​ T o ​ ​ d T ⟹ q ˙ ​ ln ( r i ​ r o ​ ​ ) = 2 πk L ( T i ​ − T o ​ ) q ˙ = 2 π k L ( T i − T o ) ln ⁡ ( r o / r i ) = T i − T o R t h , c y l \dot{q} = \frac{2 \pi k L (T_i - T_o)}{\ln(r_o / r_i)} = \frac{T_i - T_o}{R_{th,cyl}} q ˙ ​ = ln ( r o ​ / r i ​ ) 2 πk L ( T i ​ − T o ​ ) ​ = R t h , cy l ​ T i ​ − T o ​ ​

Cylindrical Thermal Resistance

The total thermal resistance for a cylindrical shell of length L L L is: R t h , c y l = ln ⁡ ( r o / r i ) 2 π k L [ hr ⋅ ∘ F Btu ] R_{th,cyl} = \frac{\ln(r_o / r_i)}{2 \pi k L} \quad \left[\frac{\text{hr}\cdot{}^\circ\text{F}}{\text{Btu}}\right] R t h , cy l ​ = 2 πk L ln ( r o ​ / r i ​ ) ​ [ Btu hr ⋅ ∘ F ​ ]

Expressed as resistance per unit linear foot of pipe length ( R t h ′ = R t h ⋅ L R'_{th} = R_{th} \cdot L R t h ′ ​ = R t h ​ ⋅ L ): R t h , c y l ′ = ln ⁡ ( r o / r i ) 2 π k [ hr ⋅ ft ⋅ ∘ F Btu ] R'_{th,cyl} = \frac{\ln(r_o / r_i)}{2 \pi k} \quad \left[\frac{\text{hr}\cdot\text{ft}\cdot{}^\circ\text{F}}{\text{Btu}}\right] R t h , cy l ′ ​ = 2 πk ln ( r o ​ / r i ​ ) ​ [ Btu hr ⋅ ft ⋅ ∘ F ​ ]

Multilayer Insulated Pipe Network

For a pipe with inside convection h i h_i h i ​ , pipe wall ( r 1 → r 2 , k p r_1 \to r_2, k_p r 1 ​ → r 2 ​ , k p ​ ), insulation layer ( r 2 → r 3 , k i n s r_2 \to r_3, k_{ins} r 2 ​ → r 3 ​ , k in s ​ ), and outer surface convection/radiation h o h_o h o ​ : q ˙ ′ = T ∞ , i − T ∞ , o R t o t a l ′ \dot{q}' = \frac{T_{\infty,i} - T_{\infty,o}}{R'_{total}} q ˙ ​ ′ = R t o t a l ′ ​ T ∞ , i ​ − T ∞ , o ​ ​ R t o t a l ′ = 1 2 π r 1 h i + ln ⁡ ( r 2 / r 1 ) 2 π k p + ln ⁡ ( r 3 / r 2 ) 2 π k i n s + 1 2 π r 3 h o R'_{total} = \frac{1}{2 \pi r_1 h_i} + \frac{\ln(r_2 / r_1)}{2 \pi k_p} + \frac{\ln(r_3 / r_2)}{2 \pi k_{ins}} + \frac{1}{2 \pi r_3 h_o} R t o t a l ′ ​ = 2 π r 1 ​ h i ​ 1 ​ + 2 π k p ​ ln ( r 2 ​ / r 1 ​ ) ​ + 2 π k in s ​ ln ( r 3 ​ / r 2 ​ ) ​ + 2 π r 3 ​ h o ​ 1 ​

Spherical Conduction Equation

For a hollow sphere of inner radius r 1 r_1 r 1 ​ and outer radius r 2 r_2 r 2 ​ (such as cryogenic storage tanks or spherical expansion vessels): q ˙ = 4 π k r 1 r 2 ( T 1 − T 2 ) r 2 − r 1 ⟹ R t h , s p h e r e = r 2 − r 1 4 π k r 1 r 2 \dot{q} = \frac{4 \pi k r_1 r_2 (T_1 - T_2)}{r_2 - r_1} \quad \implies \quad R_{th,sphere} = \frac{r_2 - r_1}{4 \pi k r_1 r_2} q ˙ ​ = r 2 ​ − r 1 ​ 4 πk r 1 ​ r 2 ​ ( T 1 ​ − T 2 ​ ) ​ ⟹ R t h , s p h ere ​ = 4 πk r 1 ​ r 2 ​ r 2 ​ − r 1 ​ ​

5. Critical Radius of Insulation

Adding insulation to a flat plane always increases conduction resistance without altering the surface area, continuously reducing heat loss. However, adding insulation to a cylindrical pipe produces two competing physical effects:

Conduction Resistance Increases: As insulation thickness increases ( r o ↑ r_o \uparrow r o ​ ↑ ), radial conduction resistance R c o n d = ln ⁡ ( r o / r i ) 2 π k L R_{cond} = \frac{\ln(r_o/r_i)}{2 \pi k L} R co n d ​ = 2 πk L l n ( r o ​ / r i ​ ) ​ increases logarithmically.

Convection Surface Area Increases: As outer radius expands ( r o ↑ r_o \uparrow r o ​ ↑ ), outer convective surface area A o = 2 π r o L A_o = 2 \pi r_o L A o ​ = 2 π r o ​ L increases, decreasing external surface convective resistance R c o n v = 1 2 π r o L h o R_{conv} = \frac{1}{2 \pi r_o L h_o} R co n v ​ = 2 π r o ​ L h o ​ 1 ​ linearly. +-----------------------------------------------------------------------------------------+

  • | THERMAL RESISTANCE VS. OUTER INSULATION RADIUS (CYLINDER) |
  • +-----------------------------------------------------------------------------------------+
  • | Resistance |
  • | ^ |
  • | | Total Resistance R_tot (Minimum at r_cr) |
  • | | \ / |
  • | | \ / |
  • | | \--------------/ <--- r_cr = k_ins / h_o (Max Heat Loss) |
  • | | . ' ` . |
  • | | . ' ` . Convection Resistance: R_conv ~ 1/r_o |
  • | | . ' ` . |
  • | +-----------------------------------------------------> Outer Radius r_o |
  • | 0 r_pipe r_cr |
  • +-----------------------------------------------------------------------------------------+
  • Mathematical Derivation of r c r r_{cr} r cr ​

To find the outer radius r o r_o r o ​ that minimizes total thermal resistance R t o t a l ′ R'_{total} R t o t a l ′ ​ per unit length: R t o t a l ′ = ln ⁡ ( r o / r i ) 2 π k i n s + 1 2 π r o h o R'_{total} = \frac{\ln(r_o / r_i)}{2 \pi k_{ins}} + \frac{1}{2 \pi r_o h_o} R t o t a l ′ ​ = 2 π k in s ​ ln ( r o ​ / r i ​ ) ​ + 2 π r o ​ h o ​ 1 ​

Differentiating with respect to r o r_o r o ​ and setting the derivative to zero: d R t o t a l ′ d r o = 1 2 π k i n s r o − 1 2 π h o r o 2 = 0 \frac{d R'_{total}}{d r_o} = \frac{1}{2 \pi k_{ins} r_o} - \frac{1}{2 \pi h_o r_o^2} = 0 d r o ​ d R t o t a l ′ ​ ​ = 2 π k in s ​ r o ​ 1 ​ − 2 π h o ​ r o 2 ​ 1 ​ = 0 1 k i n s r o = 1 h o r o 2 ⟹ r o = k i n s h o \frac{1}{k_{ins} r_o} = \frac{1}{h_o r_o^2} \implies r_o = \frac{k_{ins}}{h_o} k in s ​ r o ​ 1 ​ = h o ​ r o 2 ​ 1 ​ ⟹ r o ​ = h o ​ k in s ​ ​ r c r , c y l = k i n s h o r_{cr,cyl} = \frac{k_{ins}}{h_o} r cr , cy l ​ = h o ​ k in s ​ ​

For a spherical vessel, the critical radius is: r c r , s p h e r e = 2 k i n s h o r_{cr,sphere} = \frac{2 k_{ins}}{h_o} r cr , s p h ere ​ = h o ​ 2 k in s ​ ​

Practical Engineering Implications on the PE Exam

Small Diameter Tubing / Electrical Wires: For small refrigeration capillary tubes or electrical wires ( r b a r e < r c r r_{bare} < r_{cr} r ba re ​ < r cr ​ ), adding thin insulation increases heat dissipation, keeping electrical wires cooler.

Building HVAC Piping: For standard HVAC chilled water or steam pipes, the bare pipe outer radius r b a r e r_{bare} r ba re ​ is typically much larger than r c r r_{cr} r cr ​ (e.g., for fiberglass insulation with k = 0.025 Btu/(hr ⋅ ft ⋅ ∘ F) k = 0.025\text{ Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)} k = 0.025 Btu/(hr ⋅ ft ⋅ ∘ F) and h o = 1.5 Btu/(hr ⋅ ft 2 ⋅ ∘ F) h_o = 1.5\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} h o ​ = 1.5 Btu/(hr ⋅ ft 2 ⋅ ∘ F) , r c r = 0.025 / 1.5 = 0.0167 ft = 0.20 in. r_{cr} = 0.025 / 1.5 = 0.0167\text{ ft} = 0.20\text{ in.} r cr ​ = 0.025/1.5 = 0.0167 ft = 0.20 in. ). Since standard pipes have r o > 0.20 in. r_o > 0.20\text{ in.} r o ​ > 0.20 in. , adding insulation always reduces heat loss.

  • 6. Standard Building Material Properties & Air Film Resistances
  • Typical Material Thermal Properties (ASHRAE Fundamentals Reference)

Material Layer Thickness ( L L L ) Conductivity k k k [Btu/(hr ⋅ ft ⋅ ∘ F)] \text{[Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)]} [Btu/(hr ⋅ ft ⋅ ∘ F)] Density ρ \rho ρ [lbm/ft 3 ] \text{[lbm/ft}^3\text{]} [lbm/ft 3 ] Standard R R R -Value [hr ⋅ ft 2 ⋅ ∘ F/Btu] \text{[hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu]} [hr ⋅ ft 2 ⋅ ∘ F/Btu]

Interior Gypsum Board 0.50 in. 0.50\text{ in.} 0.50 in. 0.092 0.092 0.092 50.0 50.0 50.0 R − 0.45 R-0.45 R − 0.45

Fiberglass Batt (2x4 Cavity) 3.50 in. 3.50\text{ in.} 3.50 in. 0.0224 0.0224 0.0224 0.8 0.8 0.8 R − 13.0 R-13.0 R − 13.0

Fiberglass Batt (2x6 Cavity) 5.50 in. 5.50\text{ in.} 5.50 in. 0.0241 0.0241 0.0241 0.8 0.8 0.8 R − 19.0 R-19.0 R − 19.0

Extruded Polystyrene (XPS) 1.00 in. 1.00\text{ in.} 1.00 in. 0.0167 0.0167 0.0167 2.0 2.0 2.0 R − 5.00 R-5.00 R − 5.00

Polyisocyanurate (Foil-Faced) 1.00 in. 1.00\text{ in.} 1.00 in. 0.0128 0.0128 0.0128 2.0 2.0 2.0 R − 6.50 R-6.50 R − 6.50

Expanded Polystyrene (EPS) 1.00 in. 1.00\text{ in.} 1.00 in. 0.0208 0.0208 0.0208 1.5 1.5 1.5 R − 4.00 R-4.00 R − 4.00

Plywood / OSB Sheathing 0.50 in. 0.50\text{ in.} 0.50 in. 0.0750 0.0750 0.0750 34.0 34.0 34.0 R − 0.56 R-0.56 R − 0.56

Face Brick 3.50 in. 3.50\text{ in.} 3.50 in. 0.7500 0.7500 0.7500 120.0 120.0 120.0 R − 0.39 R-0.39 R − 0.39

Poured Concrete 8.00 in. 8.00\text{ in.} 8.00 in. 1.0400 1.0400 1.0400 140.0 140.0 140.0 R − 0.64 R-0.64 R − 0.64

Wood Stud (2x4 Douglas Fir) 3.50 in. 3.50\text{ in.} 3.50 in. 0.0800 0.0800 0.0800 32.0 32.0 32.0 R − 3.65 R-3.65 R − 3.65

ASHRAE Standard Surface Air Film Resistances ( R i R_i R i ​ and R o R_o R o ​ )

Surface Position & Heat Flow Direction Emissivity ( ε \varepsilon ε ) Air Film Condition Film Resistance R R R [hr ⋅ ft 2 ⋅ ∘ F/Btu] \text{[hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu]} [hr ⋅ ft 2 ⋅ ∘ F/Btu]

Vertical Surface (Walls), Horizontal Flow 0.90 0.90 0.90 (non-reflective) Still Air (Indoor) R i = 0.68 R_i = 0.68 R i ​ = 0.68

Horizontal Surface (Ceilings), Upward Flow 0.90 0.90 0.90 Still Air (Indoor) R i = 0.61 R_i = 0.61 R i ​ = 0.61

Horizontal Surface (Floors), Downward Flow 0.90 0.90 0.90 Still Air (Indoor) R i = 0.92 R_i = 0.92 R i ​ = 0.92

Any Orientation (Winter Exterior) Any 15 mph Wind 15\text{ mph Wind} 15 mph Wind R o = 0.17 R_o = 0.17 R o ​ = 0.17

Any Orientation (Summer Exterior) Any 7.5 mph Wind 7.5\text{ mph Wind} 7.5 mph Wind R o = 0.25 R_o = 0.25 R o ​ = 0.25

  • 7. Step-by-Step Worked Example: Multilayer Framed Exterior Wall
  • Problem Statement

An exterior wall assembly of a commercial office building in Chicago ( 400 ft 2 400\text{ ft}^2 400 ft 2 gross area) consists of the following layers from inside to outside:

Inside air film ( R i = 0.68 hr ⋅ ft 2 ⋅ ∘ F/Btu R_i = 0.68\text{ hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu} R i ​ = 0.68 hr ⋅ ft 2 ⋅ ∘ F/Btu )

1 / 2 -in. 1/2\text{-in.} 1/2 -in. gypsum wallboard ( R = 0.45 R = 0.45 R = 0.45 )

2 × 4 2\times4 2 × 4 wood framing at 16 in. 16\text{ in.} 16 in. on center ( 3.5 in. 3.5\text{ in.} 3.5 in. depth):

  • Cavity path: R − 13.0 R-13.0 R − 13.0 fiberglass batt
  • Stud path: 2 × 4 2\times4 2 × 4 wood studs ( R = 3.65 R = 3.65 R = 3.65 )

Framing factor: f f r a m e = 20 % f_{frame} = 20\% f f r am e ​ = 20% ( 0.20 0.20 0.20 ), f c a v i t y = 80 % f_{cavity} = 80\% f c a v i t y ​ = 80% ( 0.80 0.80 0.80 )

  • 1 / 2 -in. 1/2\text{-in.} 1/2 -in. OSB sheathing ( R = 0.56 R = 0.56 R = 0.56 )
  • 1.0 -in. 1.0\text{-in.} 1.0 -in. continuous XPS rigid insulation ( R = 5.00 R = 5.00 R = 5.00 )
  • 1.0 -in. 1.0\text{-in.} 1.0 -in. unventilated non-reflective air space ( R = 1.00 R = 1.00 R = 1.00 )
  • 3.5 -in. 3.5\text{-in.} 3.5 -in. clay face brick ( R = 0.39 R = 0.39 R = 0.39 )
  • Outside winter air film ( 15 mph wind 15\text{ mph wind} 15 mph wind , R o = 0.17 R_o = 0.17 R o ​ = 0.17 )

Calculate:

Total thermal resistance along the cavity path ( R c a v R_{cav} R c a v ​ ) and stud path ( R s t u d R_{stud} R s t u d ​ )

Individual U U U -factors for cavity and stud paths

Overall area-weighted U U U -factor ( U o v e r a l l U_{overall} U o v er a ll ​ ) and effective assembly R R R -value ( R e f f R_{eff} R e ff ​ )

Total steady-state winter heat loss rate q ˙ \dot{q} q ˙ ​ when T i n = 70.0 ∘ F T_{in} = 70.0^\circ\text{F} T in ​ = 70. 0 ∘ F and T o u t = 0.0 ∘ F T_{out} = 0.0^\circ\text{F} T o u t ​ = 0. 0 ∘ F

  • Temperature at the interior face of the continuous XPS insulation
  • Solution Steps

Step 1: Calculate resistance of continuous layers R c o n t = R i + R g y p + R o s b + R x p s + R a i r + R b r i c k + R o R_{cont} = R_i + R_{gyp} + R_{osb} + R_{xps} + R_{air} + R_{brick} + R_o R co n t ​ = R i ​ + R g y p ​ + R os b ​ + R x p s ​ + R ai r ​ + R b r i c k ​ + R o ​ R c o n t = 0.68 + 0.45 + 0.56 + 5.00 + 1.00 + 0.39 + 0.17 = 8.25 hr ⋅ ft 2 ⋅ ∘ F/Btu R_{cont} = 0.68 + 0.45 + 0.56 + 5.00 + 1.00 + 0.39 + 0.17 = 8.25\text{ hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu} R co n t ​ = 0.68 + 0.45 + 0.56 + 5.00 + 1.00 + 0.39 + 0.17 = 8.25 hr ⋅ ft 2 ⋅ ∘ F/Btu

Step 2: Calculate total path resistances and individual U U U -factors

Cavity Path: R c a v , t o t a l = R c o n t + R i n s u l = 8.25 + 13.00 = 21.25 hr ⋅ ft 2 ⋅ ∘ F/Btu R_{cav,total} = R_{cont} + R_{insul} = 8.25 + 13.00 = 21.25\text{ hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu} R c a v , t o t a l ​ = R co n t ​ + R in s u l ​ = 8.25 + 13.00 = 21.25 hr ⋅ ft 2 ⋅ ∘ F/Btu U c a v = 1 R c a v , t o t a l = 1 21.25 = 0.04706 Btu/(hr ⋅ ft 2 ⋅ ∘ F) U_{cav} = \frac{1}{R_{cav,total}} = \frac{1}{21.25} = 0.04706\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} U c a v ​ = R c a v , t o t a l ​ 1 ​ = 21.25 1 ​ = 0.04706 Btu/(hr ⋅ ft 2 ⋅ ∘ F)

Stud Path: R s t u d , t o t a l = R c o n t + R s t u d = 8.25 + 3.65 = 11.90 hr ⋅ ft 2 ⋅ ∘ F/Btu R_{stud,total} = R_{cont} + R_{stud} = 8.25 + 3.65 = 11.90\text{ hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu} R s t u d , t o t a l ​ = R co n t ​ + R s t u d ​ = 8.25 + 3.65 = 11.90 hr ⋅ ft 2 ⋅ ∘ F/Btu U s t u d = 1 R s t u d , t o t a l = 1 11.90 = 0.08403 Btu/(hr ⋅ ft 2 ⋅ ∘ F) U_{stud} = \frac{1}{R_{stud,total}} = \frac{1}{11.90} = 0.08403\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} U s t u d ​ = R s t u d , t o t a l ​ 1 ​ = 11.90 1 ​ = 0.08403 Btu/(hr ⋅ ft 2 ⋅ ∘ F)

Step 3: Calculate area-weighted overall U U U -factor and effective R R R -value U o v e r a l l = ( 1 − f f r a m e ) U c a v + f f r a m e U s t u d = ( 0.80 × 0.04706 ) + ( 0.20 × 0.08403 ) U_{overall} = (1 - f_{frame}) U_{cav} + f_{frame} U_{stud} = (0.80 \times 0.04706) + (0.20 \times 0.08403) U o v er a ll ​ = ( 1 − f f r am e ​ ) U c a v ​ + f f r am e ​ U s t u d ​ = ( 0.80 × 0.04706 ) + ( 0.20 × 0.08403 ) U o v e r a l l = 0.03765 + 0.01681 = 0.05446 Btu/(hr ⋅ ft 2 ⋅ ∘ F) U_{overall} = 0.03765 + 0.01681 = 0.05446\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} U o v er a ll ​ = 0.03765 + 0.01681 = 0.05446 Btu/(hr ⋅ ft 2 ⋅ ∘ F) R e f f = 1 U o v e r a l l = 1 0.05446 = 18.36 hr ⋅ ft 2 ⋅ ∘ F/Btu R_{eff} = \frac{1}{U_{overall}} = \frac{1}{0.05446} = 18.36\text{ hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu} R e ff ​ = U o v er a ll ​ 1 ​ = 0.05446 1 ​ = 18.36 hr ⋅ ft 2 ⋅ ∘ F/Btu

Step 4: Calculate total heat loss rate q ˙ \dot{q} q ˙ ​ q ˙ = U o v e r a l l A ( T i n − T o u t ) = 0.05446 × 400 × ( 70.0 − 0.0 ) = 0.05446 × 400 × 70.0 = 1524.9 Btu/hr \dot{q} = U_{overall} A (T_{in} - T_{out}) = 0.05446 \times 400 \times (70.0 - 0.0) = 0.05446 \times 400 \times 70.0 = 1524.9\text{ Btu/hr} q ˙ ​ = U o v er a ll ​ A ( T in ​ − T o u t ​ ) = 0.05446 × 400 × ( 70.0 − 0.0 ) = 0.05446 × 400 × 70.0 = 1524.9 Btu/hr

Step 5: Calculate temperature at interior face of continuous XPS insulation Along the predominant cavity path ( q c a v ′ ′ = U c a v Δ T = 0.04706 × 70.0 = 3.294 Btu/(hr ⋅ ft 2 ) q''_{cav} = U_{cav} \Delta T = 0.04706 \times 70.0 = 3.294\text{ Btu/(hr}\cdot\text{ft}^2) q c a v ′′ ​ = U c a v ​ Δ T = 0.04706 × 70.0 = 3.294 Btu/(hr ⋅ ft 2 ) ):

Resistance from indoor air to the interior face of XPS: R i n → X P S = R i + R g y p + R c a v + R o s b = 0.68 + 0.45 + 13.00 + 0.56 = 14.69 hr ⋅ ft 2 ⋅ ∘ F/Btu R_{in \to XPS} = R_i + R_{gyp} + R_{cav} + R_{osb} = 0.68 + 0.45 + 13.00 + 0.56 = 14.69\text{ hr}\cdot\text{ft}^2\cdot{}^\circ\text{F/Btu} R in → XPS ​ = R i ​ + R g y p ​ + R c a v ​ + R os b ​ = 0.68 + 0.45 + 13.00 + 0.56 = 14.69 hr ⋅ ft 2 ⋅ ∘ F/Btu T X P S , i n t = T i n − q c a v ′ ′ ⋅ R i n → X P S = 70.0 − ( 3.294 × 14.69 ) = 70.0 − 48.39 = 21.61 ∘ F T_{XPS,int} = T_{in} - q''_{cav} \cdot R_{in \to XPS} = 70.0 - (3.294 \times 14.69) = 70.0 - 48.39 = 21.61^\circ\text{F} T XPS , in t ​ = T in ​ − q c a v ′′ ​ ⋅ R in → XPS ​ = 70.0 − ( 3.294 × 14.69 ) = 70.0 − 48.39 = 21.6 1 ∘ F

This confirms that without sufficient continuous exterior insulation, the cavity condensation plane remains well below the indoor dew point ( 37 ∘ F ~37^\circ\text{F} 3 7 ∘ F at 50 % RH 50\%\text{ RH} 50% RH ), validating ASHRAE building science guidelines.