Study guide
4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients
Key Takeaways Explain This Topic AI
Newton's Law of Cooling governs convection: q ˙ c o n v = h c A ( T s − T ∞ ) = T s − T ∞ R c o n v \dot{q}_{conv} = h_c A (T_s - T_\infty) = \frac{T_s - T_\infty}{R_{conv}} q ˙ co n v = h c A ( T s − T ∞ ) = R co n v T s − T ∞ , where h c h_c h c is the convective heat transfer coefficient in Btu/(hr ⋅ ft 2 ⋅ ∘ F) \text{Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} Btu/(hr ⋅ ft 2 ⋅ ∘ F) or W/(m 2 ⋅ K) \text{W/(m}^2\cdot\text{K)} W/(m 2 ⋅ K) .
The fundamental dimensionless numbers in convection are Reynolds ( Re = ρ V D μ \text{Re} = \frac{\rho V D}{\mu} Re = μ ρ V D ), Prandtl ( Pr = c p μ k = ν α \text{Pr} = \frac{c_p \mu}{k} = \frac{\nu}{\alpha} Pr = k c p μ = α ν ), Nusselt ( Nu = h D k f \text{Nu} = \frac{h D}{k_f} Nu = k f h D ), Grashof ( Gr = g β Δ T L 3 ν 2 \text{Gr} = \frac{g \beta \Delta T L^3}{\nu^2} Gr = ν 2 g β Δ T L 3 ), and Rayleigh ( Ra = Gr ⋅ Pr \text{Ra} = \text{Gr}\cdot\text{Pr} Ra = Gr ⋅ Pr ).
For fully developed turbulent flow in circular tubes ( Re D ≥ 10 , 000 \text{Re}_D \ge 10,000 Re D ≥ 10 , 000 , 0.6 ≤ Pr ≤ 160 0.6 \le \text{Pr} \le 160 0.6 ≤ Pr ≤ 160 ), the Dittus-Boelter correlation gives Nu D = 0.023 Re D 0.8 Pr n \text{Nu}_D = 0.023 \text{Re}_D^{0.8} \text{Pr}^n Nu D = 0.023 Re D 0.8 Pr n with n = 0.4 n = 0.4 n = 0.4 for heating the fluid and n = 0.3 n = 0.3 n = 0.3 for cooling.
Non-circular ducts utilize hydraulic diameter D h = 4 A c P w D_h = \frac{4 A_c}{P_w} D h = P w 4 A c ; for rectangular ducts of width a a a and height b b b , D h = 2 a b a + b D_h = \frac{2 a b}{a + b} D h = a + b 2 ab .
Natural convection is driven by buoyancy forces where Nu = C Ra m \text{Nu} = C \text{Ra}^m Nu = C Ra m ( m = 1 / 4 m = 1/4 m = 1/4 for laminar boundary layers Ra < 10 9 \text{Ra} < 10^9 Ra < 1 0 9 , and m = 1 / 3 m = 1/3 m = 1/3 for turbulent boundary layers Ra ≥ 10 9 \text{Ra} \ge 10^9 Ra ≥ 1 0 9 ).
Last updated: August 2026
4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients
Convective heat transfer is the transport of energy between a solid boundary and an adjacent moving fluid (liquid or gas), combining microscopic molecular conduction and macroscopic bulk fluid advection. In HVAC and refrigeration engineering, convection occurs inside hydronic chiller/boiler tubes, across finned air-conditioning coils, through air supply ductwork, and along building architectural surfaces. Accurately determining convective heat transfer coefficients ( h c h_c h c ) via dimensionless empirical correlations is critical for equipment sizing on the NCEES PE Mechanical exam.
1. Newton's Law of Cooling & Boundary Layer Theory
Convective heat transfer is governed by Newton's Law of Cooling : q ˙ c o n v = h c A ( T s − T ∞ ) \dot{q}_{conv} = h_c A (T_s - T_\infty) q ˙ co n v = h c A ( T s − T ∞ )
Where:
q ˙ c o n v = convective heat transfer rate ( Btu/hr or W ) \dot{q}_{conv} = \text{convective heat transfer rate } (\text{Btu/hr or W}) q ˙ co n v = convective heat transfer rate ( Btu/hr or W )
h c = convective heat transfer coefficient ( Btu/(hr ⋅ ft 2 ⋅ ∘ F) or W/(m 2 ⋅ K) ) h_c = \text{convective heat transfer coefficient } (\text{Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} \text{or W/(m}^2\cdot\text{K)}) h c = convective heat transfer coefficient ( Btu/(hr ⋅ ft 2 ⋅ ∘ F) or W/(m 2 ⋅ K) )
A = surface area in contact with fluid ( ft 2 or m 2 ) A = \text{surface area in contact with fluid } (\text{ft}^2 \text{ or m}^2) A = surface area in contact with fluid ( ft 2 or m 2 )
T s = solid surface temperature ( ∘ F or ∘ C ) T_s = \text{solid surface temperature } ({}^\circ\text{F or } {}^\circ\text{C}) T s = solid surface temperature ( ∘ F or ∘ C )
T ∞ = free-stream bulk fluid temperature ( ∘ F or ∘ C ) T_\infty = \text{free-stream bulk fluid temperature } ({}^\circ\text{F or } {}^\circ\text{C}) T ∞ = free-stream bulk fluid temperature ( ∘ F or ∘ C )
The equivalent convective thermal resistance is: R c o n v = 1 h c A [ hr ⋅ ∘ F Btu ] R_{conv} = \frac{1}{h_c A} \quad \left[\frac{\text{hr}\cdot{}^\circ\text{F}}{\text{Btu}}\right] R co n v = h c A 1 [ Btu hr ⋅ ∘ F ] +-----------------------------------------------------------------------------------------+
- | HYDRODYNAMIC AND THERMAL BOUNDARY LAYERS OVER A FLAT SURFACE |
- +-----------------------------------------------------------------------------------------+
- | Free Stream: V_inf, T_inf |
- | ====================> |
- | . - ~ ~ ~ - . <--- Hydrodynamic Boundary Layer delta(x) |
- | . ' ` . Velocity transitions from 0 at wall to V_inf |
- | . ' - - - - - - - - - - - ` <--- Thermal Boundary Layer delta_t(x) |
- | . ' ` Temp transitions from T_s at wall to T_inf |
- | +-------------------------------------------------------------------------------------+ |
- | | Solid Surface at Temperature T_s (No-Slip Condition: u(y=0) = 0) | |
- +-----------------------------------------------------------------------------------------+
- Boundary Layer Mechanics
When fluid flows past a stationary surface, viscous shear stresses create a hydrodynamic (velocity) boundary layer of thickness δ ( x ) \delta(x) δ ( x ) , where local velocity transitions from zero at the wall (the no-slip boundary condition) to 99 % 99\% 99% of the free-stream velocity V ∞ V_\infty V ∞ . Concurrently, a thermal boundary layer of thickness δ t ( x ) \delta_t(x) δ t ( x ) develops where temperature transitions from T s T_s T s to T ∞ T_\infty T ∞ . Because fluid velocity is zero at the solid interface, heat transfer across the interface occurs entirely by pure conduction through the fluid film: q ′ ′ = − k f ∂ T ∂ y ∣ y = 0 = h c ( T s − T ∞ ) ⟹ h c = − k f ∂ T ∂ y ∣ y = 0 T s − T ∞ q'' = -k_f \left.\frac{\partial T}{\partial y}\right|_{y=0} = h_c (T_s - T_\infty) \implies h_c = \frac{-k_f \left.\frac{\partial T}{\partial y}\right|_{y=0}}{T_s - T_\infty} q ′′ = − k f ∂ y ∂ T y = 0 = h c ( T s − T ∞ ) ⟹ h c = T s − T ∞ − k f ∂ y ∂ T y = 0
Where k f k_f k f is the fluid thermal conductivity. Thinner boundary layers produce steeper temperature gradients ∂ T ∂ y \frac{\partial T}{\partial y} ∂ y ∂ T , resulting in substantially higher convection coefficients h c h_c h c .
2. Fundamental Dimensionless Numbers in Convection
Dimensionless analysis reduces complex multi-variable fluid-thermal equations into standard governing parameters: +-----------------------------------------------------------------------------------------+
- | SUMMARY OF PRIMARY DIMENSIONLESS GROUPS |
- +-----------------------------------------------------------------------------------------+
- | Reynolds (Re): Re = (rho * V * L) / mu = (V * L) / nu [Inertia / Viscous] |
- | Prandtl (Pr): Pr = nu / alpha = (c_p * mu) / k_f [Momentum / Thermal Diff] |
- | Nusselt (Nu): Nu = (h * L) / k_f [Convection / Conduction] |
- | Grashof (Gr): Gr = (g * beta * Delta_T * L^3) / nu^2 [Buoyancy / Viscous] |
- | Rayleigh (Ra): Ra = Gr * Pr = (g * beta * Delta_T * L^3)/(nu*alpha) [Natural Convect] |
- +-----------------------------------------------------------------------------------------+
- 1. Reynolds Number ( Re \text{Re} Re )
Represents the ratio of dynamic inertial forces to viscous shear forces: Re = ρ V D μ = V D ν \text{Re} = \frac{\rho V D}{\mu} = \frac{V D}{\nu} Re = μ ρ V D = ν V D
Internal Flow in Circular Pipes:
- Laminar Regime: Re < 2 , 300 \text{Re} < 2,300 Re < 2 , 300
- Transition Regime: 2 , 300 ≤ Re ≤ 10 , 000 2,300 \le \text{Re} \le 10,000 2 , 300 ≤ Re ≤ 10 , 000
- Fully Turbulent Regime: Re > 10 , 000 \text{Re} > 10,000 Re > 10 , 000
- 2. Prandtl Number ( Pr \text{Pr} Pr )
Represents the ratio of momentum molecular diffusivity ( ν = μ / ρ \nu = \mu/\rho ν = μ / ρ ) to thermal molecular diffusivity ( α = k / ( ρ c p ) \alpha = k/(\rho c_p) α = k / ( ρ c p ) ): Pr = ν α = c p μ k f \text{Pr} = \frac{\nu}{\alpha} = \frac{c_p \mu}{k_f} Pr = α ν = k f c p μ
Pr ≈ 0.70 − 0.72 \text{Pr} \approx 0.70 - 0.72 Pr ≈ 0.70 − 0.72 for air and common gases at atmospheric conditions
Pr ≈ 2.0 − 10.0 \text{Pr} \approx 2.0 - 10.0 Pr ≈ 2.0 − 10.0 for liquid water ( 40 ∘ F 40^\circ\text{F} 4 0 ∘ F to 200 ∘ F 200^\circ\text{F} 20 0 ∘ F )
- Pr ≈ 50 − 10 , 000 \text{Pr} \approx 50 - 10,000 Pr ≈ 50 − 10 , 000 for heavy oils and glycols
- Pr ≪ 1 \text{Pr} \ll 1 Pr ≪ 1 ( 0.01 ~0.01 0.01 ) for liquid metals
- 3. Nusselt Number ( Nu \text{Nu} Nu )
Represents the ratio of convective heat transfer to pure molecular conduction across a fluid layer of characteristic length L L L : Nu = h c L k f \text{Nu} = \frac{h_c L}{k_f} Nu = k f h c L
Once Nu \text{Nu} Nu is calculated from an empirical correlation, the convective coefficient is determined directly: h c = Nu ⋅ k f L h_c = \frac{\text{Nu} \cdot k_f}{L} h c = L Nu ⋅ k f
4. Grashof Number ( Gr \text{Gr} Gr ) and Rayleigh Number ( Ra \text{Ra} Ra )
In natural (free) convection, fluid motion is induced by buoyancy forces resulting from temperature-driven density differences: Gr = g β ( T s − T ∞ ) L 3 ν 2 \text{Gr} = \frac{g \beta (T_s - T_\infty) L^3}{\nu^2} Gr = ν 2 g β ( T s − T ∞ ) L 3 Ra = Gr ⋅ Pr = g β ( T s − T ∞ ) L 3 ν α \text{Ra} = \text{Gr} \cdot \text{Pr} = \frac{g \beta (T_s - T_\infty) L^3}{\nu \alpha} Ra = Gr ⋅ Pr = να g β ( T s − T ∞ ) L 3
Where:
g = gravitational acceleration ( 32.174 ft/s 2 or 9.807 m/s 2 ) g = \text{gravitational acceleration } (32.174\text{ ft/s}^2 \text{ or } 9.807\text{ m/s}^2) g = gravitational acceleration ( 32.174 ft/s 2 or 9.807 m/s 2 )
β = volumetric thermal expansion coefficient ( ∘ R − 1 or K − 1 ) \beta = \text{volumetric thermal expansion coefficient } ({}^\circ\text{R}^{-1} \text{ or } \text{K}^{-1}) β = volumetric thermal expansion coefficient ( ∘ R − 1 or K − 1 ) ; for ideal gases, β = 1 T f i l m = 1 T f (in ∘ R) \beta = \frac{1}{T_{film}} = \frac{1}{T_f\text{ (in }{}^\circ\text{R)}} β = T f i l m 1 = T f (in ∘ R) 1
T f = T s + T ∞ 2 = film temperature at which fluid properties are evaluated T_f = \frac{T_s + T_\infty}{2} = \text{film temperature at which fluid properties are evaluated} T f = 2 T s + T ∞ = film temperature at which fluid properties are evaluated
- 3. Forced Convection Correlations (Internal Flow)
- Fully Developed Turbulent Flow in Smooth Pipes
For turbulent flow in circular tubes ( Re D ≥ 10 , 000 \text{Re}_D \ge 10,000 Re D ≥ 10 , 000 , 0.6 ≤ Pr ≤ 160 0.6 \le \text{Pr} \le 160 0.6 ≤ Pr ≤ 160 , and L D ≥ 10 \frac{L}{D} \ge 10 D L ≥ 10 ), the Dittus-Boelter equation is the standard relation in the NCEES Reference Handbook: Nu D = 0.023 Re D 0.8 Pr n \text{Nu}_D = 0.023 \text{Re}_D^{0.8} \text{Pr}^n Nu D = 0.023 Re D 0.8 Pr n
Where the exponent n n n depends on the direction of heat transfer:
n = 0.4 n = 0.4 n = 0.4 when the fluid is being heated ( T s > T b T_s > T_b T s > T b , e.g., heating coils, boiler tubes)
n = 0.3 n = 0.3 n = 0.3 when the fluid is being cooled ( T s < T b T_s < T_b T s < T b , e.g., chiller evaporator tubes, cooling coils)
All fluid properties are evaluated at the bulk mean fluid temperature T b T_b T b .
Gnielinski Correlation (Higher Accuracy for 3 , 000 ≤ Re D ≤ 5 × 10 6 3,000 \le \text{Re}_D \le 5 \times 10^6 3 , 000 ≤ Re D ≤ 5 × 1 0 6 )
When greater precision is required across the transition-to-turbulent region ( 0.5 ≤ Pr ≤ 2000 0.5 \le \text{Pr} \le 2000 0.5 ≤ Pr ≤ 2000 ): Nu D = ( f / 8 ) ( Re D − 1000 ) Pr 1 + 12.7 ( f / 8 ) 1 / 2 ( Pr 2 / 3 − 1 ) \text{Nu}_D = \frac{(f/8)(\text{Re}_D - 1000)\text{Pr}}{1 + 12.7(f/8)^{1/2}(\text{Pr}^{2/3} - 1)} Nu D = 1 + 12.7 ( f /8 ) 1/2 ( Pr 2/3 − 1 ) ( f /8 ) ( Re D − 1000 ) Pr
Where f f f is the Darcy friction factor for smooth tubes: f = ( 0.790 ln ( Re D ) − 1.64 ) − 2 f = (0.790 \ln(\text{Re}_D) - 1.64)^{-2} f = ( 0.790 ln ( Re D ) − 1.64 ) − 2 .
Laminar Flow in Circular Tubes ( Re D < 2 , 300 \text{Re}_D < 2,300 Re D < 2 , 300 )
For fully developed laminar internal flow, Nu \text{Nu} Nu is independent of Reynolds and Prandtl numbers:
Constant Surface Heat Flux ( q ′ ′ = constant q'' = \text{constant} q ′′ = constant ): Nu D = h D k f = 4.364 \text{Nu}_D = \frac{h D}{k_f} = 4.364 Nu D = k f h D = 4.364
Constant Surface Temperature ( T s = constant T_s = \text{constant} T s = constant ): Nu D = h D k f = 3.656 \text{Nu}_D = \frac{h D}{k_f} = 3.656 Nu D = k f h D = 3.656
Non-Circular Ducts & Hydraulic Diameter ( D h D_h D h )
For non-circular ducts (rectangular HVAC ducts, annular passages), the characteristic dimension is the hydraulic diameter : D h = 4 A c P w D_h = \frac{4 A_c}{P_w} D h = P w 4 A c
Where:
A c = cross-sectional flow area ( ft 2 ) A_c = \text{cross-sectional flow area } (\text{ft}^2) A c = cross-sectional flow area ( ft 2 )
P w = wetted perimeter in contact with fluid ( ft ) P_w = \text{wetted perimeter in contact with fluid } (\text{ft}) P w = wetted perimeter in contact with fluid ( ft )
For a rectangular duct of cross-sectional width a a a and height b b b : D h = 4 ( a b ) 2 ( a + b ) = 2 a b a + b D_h = \frac{4 (a b)}{2(a + b)} = \frac{2 a b}{a + b} D h = 2 ( a + b ) 4 ( ab ) = a + b 2 ab
For an annular pipe (inner pipe OD = D 1 D_1 D 1 , outer pipe ID = D 2 D_2 D 2 ): D h = 4 [ π 4 ( D 2 2 − D 1 2 ) ] π ( D 2 + D 1 ) = D 2 − D 1 D_h = \frac{4 \left[\frac{\pi}{4}(D_2^2 - D_1^2)\right]}{\pi (D_2 + D_1)} = D_2 - D_1 D h = π ( D 2 + D 1 ) 4 [ 4 π ( D 2 2 − D 1 2 ) ] = D 2 − D 1
- 4. Forced Convection Correlations (External Flow)
- External Flow Over Flat Surfaces
For fluid flowing parallel to a flat plate of length L L L :
Laminar Boundary Layer ( Re x < 5 × 10 5 \text{Re}_x < 5 \times 10^5 Re x < 5 × 1 0 5 ): Nu x = 0.332 Re x 1 / 2 Pr 1 / 3 ⟹ Nu ‾ L = 0.664 Re L 1 / 2 Pr 1 / 3 \text{Nu}_x = 0.332 \text{Re}_x^{1/2} \text{Pr}^{1/3} \quad \implies \quad \overline{\text{Nu}}_L = 0.664 \text{Re}_L^{1/2} \text{Pr}^{1/3} Nu x = 0.332 Re x 1/2 Pr 1/3 ⟹ Nu L = 0.664 Re L 1/2 Pr 1/3
Turbulent Boundary Layer ( Re x ≥ 5 × 10 5 \text{Re}_x \ge 5 \times 10^5 Re x ≥ 5 × 1 0 5 ): Nu x = 0.0296 Re x 4 / 5 Pr 1 / 3 ⟹ Nu ‾ L = 0.037 Re L 4 / 5 Pr 1 / 3 \text{Nu}_x = 0.0296 \text{Re}_x^{4/5} \text{Pr}^{1/3} \quad \implies \quad \overline{\text{Nu}}_L = 0.037 \text{Re}_L^{4/5} \text{Pr}^{1/3} Nu x = 0.0296 Re x 4/5 Pr 1/3 ⟹ Nu L = 0.037 Re L 4/5 Pr 1/3
Cross-Flow Across Single Cylinders & Tube Banks
For cross-flow across a single tube of outer diameter D D D (Hilpert correlation): Nu ‾ D = C Re D m Pr 1 / 3 \overline{\text{Nu}}_D = C \text{Re}_D^m \text{Pr}^{1/3} Nu D = C Re D m Pr 1/3
In finned-tube HVAC cooling and heating coils, air flows across tube banks arranged in in-line or staggered configurations. Staggered tube banks produce higher turbulence and convective heat transfer coefficients for equivalent air face velocities at the expense of higher fan static pressure drop.
Loading diagram... Tube Bank Layouts: In-Line vs Staggered Coil Geometries
5. Natural (Free) Convection Correlations
Natural convection correlations take the general power-law form: Nu ‾ L = h ˉ L k f = C Ra L m = C ( Gr L ⋅ Pr ) m \overline{\text{Nu}}_L = \frac{\bar{h} L}{k_f} = C \text{Ra}_L^m = C (\text{Gr}_L \cdot \text{Pr})^m Nu L = k f h ˉ L = C Ra L m = C ( Gr L ⋅ Pr ) m
Where the constants C C C and m m m depend on geometry, orientation, and flow regime:
- Laminar Flow ( Ra < 10 9 \text{Ra} < 10^9 Ra < 1 0 9 ): m = 1 / 4 m = 1/4 m = 1/4 ( 0.25 0.25 0.25 )
- Turbulent Flow ( Ra ≥ 10 9 \text{Ra} \ge 10^9 Ra ≥ 1 0 9 ): m = 1 / 3 m = 1/3 m = 1/3 ( 0.333 0.333 0.333 )
- Summary of Natural Convection Geometries (ASHRAE / NCEES Standards)
Surface Geometry & Orientation Characteristic Length ( L L L ) Rayleigh Number Range Correlation Equation ( Nu ‾ L \overline{\text{Nu}}_L Nu L )
Vertical Plate / Vertical Wall Height H H H 10 4 ≤ Ra L ≤ 10 9 10^4 \le \text{Ra}_L \le 10^9 1 0 4 ≤ Ra L ≤ 1 0 9 (Laminar) Nu ‾ L = 0.59 Ra L 1 / 4 \overline{\text{Nu}}_L = 0.59 \text{Ra}_L^{1/4} Nu L = 0.59 Ra L 1/4
Vertical Plate / Vertical Wall Height H H H 10 9 ≤ Ra L ≤ 10 13 10^9 \le \text{Ra}_L \le 10^{13} 1 0 9 ≤ Ra L ≤ 1 0 13 (Turbulent) Nu ‾ L = 0.10 Ra L 1 / 3 \overline{\text{Nu}}_L = 0.10 \text{Ra}_L^{1/3} Nu L = 0.10 Ra L 1/3
Horizontal Cylinder (Pipes) Outer Diameter D D D 10 4 ≤ Ra D ≤ 10 9 10^4 \le \text{Ra}_D \le 10^9 1 0 4 ≤ Ra D ≤ 1 0 9 Nu ‾ D = 0.53 Ra D 1 / 4 \overline{\text{Nu}}_D = 0.53 \text{Ra}_D^{1/4} Nu D = 0.53 Ra D 1/4
Horizontal Cylinder (Pipes) Outer Diameter D D D 10 9 ≤ Ra D ≤ 10 12 10^9 \le \text{Ra}_D \le 10^{12} 1 0 9 ≤ Ra D ≤ 1 0 12 Nu ‾ D = 0.13 Ra D 1 / 3 \overline{\text{Nu}}_D = 0.13 \text{Ra}_D^{1/3} Nu D = 0.13 Ra D 1/3
Hot Horizontal Plate Facing Up L c = A s P L_c = \frac{A_s}{P} L c = P A s 10 4 ≤ Ra L ≤ 10 7 10^4 \le \text{Ra}_L \le 10^7 1 0 4 ≤ Ra L ≤ 1 0 7 (Laminar) Nu ‾ L = 0.54 Ra L 1 / 4 \overline{\text{Nu}}_L = 0.54 \text{Ra}_L^{1/4} Nu L = 0.54 Ra L 1/4
Hot Horizontal Plate Facing Up L c = A s P L_c = \frac{A_s}{P} L c = P A s 10 7 ≤ Ra L ≤ 10 11 10^7 \le \text{Ra}_L \le 10^{11} 1 0 7 ≤ Ra L ≤ 1 0 11 (Turbulent) Nu ‾ L = 0.15 Ra L 1 / 3 \overline{\text{Nu}}_L = 0.15 \text{Ra}_L^{1/3} Nu L = 0.15 Ra L 1/3
Hot Horizontal Plate Facing Down L c = A s P L_c = \frac{A_s}{P} L c = P A s 10 4 ≤ Ra L ≤ 10 9 10^4 \le \text{Ra}_L \le 10^9 1 0 4 ≤ Ra L ≤ 1 0 9 Nu ‾ L = 0.27 Ra L 1 / 4 \overline{\text{Nu}}_L = 0.27 \text{Ra}_L^{1/4} Nu L = 0.27 Ra L 1/4
6. Phase Change Convection: Boiling & Condensation Fundamentals
Phase-change convective processes provide the highest heat transfer coefficients in HVAC and refrigeration engineering ( h ≈ 500 to 10 , 000 + Btu/(hr ⋅ ft 2 ⋅ ∘ F) h \approx 500 \text{ to } 10,000+\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} h ≈ 500 to 10 , 000 + Btu/(hr ⋅ ft 2 ⋅ ∘ F) ).
The Pool Boiling Curve
When a submerged heating surface operates at temperature T s T_s T s above the fluid saturation temperature T s a t T_{sat} T s a t (excess temperature Δ T e = T s − T s a t \Delta T_e = T_s - T_{sat} Δ T e = T s − T s a t ):
Natural Convection Regime ( Δ T e < 9 ∘ F \Delta T_e < 9^\circ\text{F} Δ T e < 9 ∘ F / 5 ∘ C 5^\circ\text{C} 5 ∘ C ): Liquid motion is driven purely by natural convection without vapor bubble formation.
Nucleate Boiling Regime ( 9 ∘ F < Δ T e < 54 ∘ F 9^\circ\text{F} < \Delta T_e < 54^\circ\text{F} 9 ∘ F < Δ T e < 5 4 ∘ F / 5 ∘ C < Δ T e < 30 ∘ C 5^\circ\text{C} < \Delta T_e < 30^\circ\text{C} 5 ∘ C < Δ T e < 3 0 ∘ C ): Vapor bubbles nucleate at microscopic surface cavities, detach rapidly, and create vigorous fluid agitation. This regime yields maximum heat transfer efficiency and governs direct-expansion (DX) and flooded refrigeration evaporators.
Critical Heat Flux ( q m a x ′ ′ q''_{max} q ma x ′′ / Departure from Nucleate Boiling - DNB): The peak heat flux point. Exceeding q m a x ′ ′ q''_{max} q ma x ′′ causes vapor bubbles to coalesce into an insulating blanket.
Film Boiling Regime (Large Δ T e \Delta T_e Δ T e ): A continuous vapor film completely blankets the heater surface, dropping h h h drastically and causing severe surface temperature spikes (burnout).
Condensation: Film vs. Dropwise
Film Condensation (Nusselt Film Theory): Liquid condensate forms a continuous laminar liquid film that flows downward under gravity. The liquid film introduces a conductive thermal barrier, reducing h h h .
Dropwise Condensation: Condensate forms discrete droplets that break away, keeping the cold surface directly exposed. Dropwise condensation achieves heat transfer coefficients 4 to 8 times higher than film condensation.
- 7. Step-by-Step Worked Example: Internal Forced Convection Sizing
- Problem Statement
Water at a bulk mean temperature of T b = 140.0 ∘ F T_b = 140.0^\circ\text{F} T b = 140. 0 ∘ F flows through a 1 -inch 1\text{-inch} 1 -inch nominal Type L copper pipe with an inside diameter of D i = 1.025 in. = 0.08542 ft D_i = 1.025\text{ in.} = 0.08542\text{ ft} D i = 1.025 in. = 0.08542 ft at a volumetric flow rate of 5.0 GPM 5.0\text{ GPM} 5.0 GPM . The pipe wall is maintained at T s = 160.0 ∘ F T_s = 160.0^\circ\text{F} T s = 160. 0 ∘ F by an external heating source (heating fluid, n = 0.4 n = 0.4 n = 0.4 ).
From NCEES water property tables at 140 ∘ F 140^\circ\text{F} 14 0 ∘ F ( 60 ∘ C 60^\circ\text{C} 6 0 ∘ C ):
Density: ρ = 61.38 lbm/ft 3 \rho = 61.38\text{ lbm/ft}^3 ρ = 61.38 lbm/ft 3
Dynamic Viscosity: μ = 1.14 × 10 − 3 lbm/(ft ⋅ s) = 4.104 lbm/(ft ⋅ hr) \mu = 1.14 \times 10^{-3}\text{ lbm/(ft}\cdot\text{s)} = 4.104\text{ lbm/(ft}\cdot\text{hr)} μ = 1.14 × 1 0 − 3 lbm/(ft ⋅ s) = 4.104 lbm/(ft ⋅ hr)
Kinematic Viscosity: ν = 1.857 × 10 − 5 ft 2 / s \nu = 1.857 \times 10^{-5}\text{ ft}^2/\text{s} ν = 1.857 × 1 0 − 5 ft 2 / s
Thermal Conductivity: k f = 0.376 Btu/(hr ⋅ ft ⋅ ∘ F) k_f = 0.376\text{ Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)} k f = 0.376 Btu/(hr ⋅ ft ⋅ ∘ F)
Specific Heat: c p = 1.000 Btu/(lbm ⋅ ∘ F) c_p = 1.000\text{ Btu/(lbm}\cdot{}^\circ\text{F)} c p = 1.000 Btu/(lbm ⋅ ∘ F)
Prandtl Number: Pr = 3.01 \text{Pr} = 3.01 Pr = 3.01
Calculate:
Cross-sectional flow area A c A_c A c ( ft 2 \text{ft}^2 ft 2 ) and mean flow velocity V V V ( ft/s \text{ft/s} ft/s )
- Reynolds number Re D \text{Re}_D Re D and flow regime
- Nusselt number Nu D \text{Nu}_D Nu D via the Dittus-Boelter equation
Internal convective heat transfer coefficient h i h_i h i ( Btu/(hr ⋅ ft 2 ⋅ ∘ F) \text{Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} Btu/(hr ⋅ ft 2 ⋅ ∘ F) )
Convective heat gain rate per linear foot of pipe length q ˙ ′ \dot{q}' q ˙ ′ ( Btu/(hr ⋅ ft) \text{Btu/(hr}\cdot\text{ft)} Btu/(hr ⋅ ft) )
Solution Steps
Step 1: Calculate flow area and fluid velocity A c = π 4 D i 2 = π 4 ( 0.08542 ft ) 2 = 0.005731 ft 2 A_c = \frac{\pi}{4} D_i^2 = \frac{\pi}{4} (0.08542\text{ ft})^2 = 0.005731\text{ ft}^2 A c = 4 π D i 2 = 4 π ( 0.08542 ft ) 2 = 0.005731 ft 2 Q = 5.0 GPM × ( 0.13368 ft 3 1 gal ) × ( 1 min 60 s ) = 0.01114 ft 3 / s Q = 5.0\text{ GPM} \times \left(\frac{0.13368\text{ ft}^3}{1\text{ gal}}\right) \times \left(\frac{1\text{ min}}{60\text{ s}}\right) = 0.01114\text{ ft}^3/\text{s} Q = 5.0 GPM × ( 1 gal 0.13368 ft 3 ) × ( 60 s 1 min ) = 0.01114 ft 3 / s V = Q A c = 0.01114 ft 3 / s 0.005731 ft 2 = 1.944 ft/s V = \frac{Q}{A_c} = \frac{0.01114\text{ ft}^3/\text{s}}{0.005731\text{ ft}^2} = 1.944\text{ ft/s} V = A c Q = 0.005731 ft 2 0.01114 ft 3 / s = 1.944 ft/s
Step 2: Calculate Reynolds number Re D = V D i ν = 1.944 ft/s × 0.08542 ft 1.857 × 10 − 5 ft 2 / s = 0.16606 1.857 × 10 − 5 = 8942 \text{Re}_D = \frac{V D_i}{\nu} = \frac{1.944\text{ ft/s} \times 0.08542\text{ ft}}{1.857 \times 10^{-5}\text{ ft}^2/\text{s}} = \frac{0.16606}{1.857 \times 10^{-5}} = 8942 Re D = ν V D i = 1.857 × 1 0 − 5 ft 2 / s 1.944 ft/s × 0.08542 ft = 1.857 × 1 0 − 5 0.16606 = 8942
Alternatively, using mass flow rate m ˙ = ρ Q = 61.38 × ( 0.01114 × 3600 ) = 2461.4 lbm/hr \dot{m} = \rho Q = 61.38 \times (0.01114 \times 3600) = 2461.4\text{ lbm/hr} m ˙ = ρQ = 61.38 × ( 0.01114 × 3600 ) = 2461.4 lbm/hr : Re D = 4 m ˙ π D i μ = 4 × 2461.4 π × 0.08542 × 4.104 = 9845.6 1.1014 = 8939 ≈ 8940 \text{Re}_D = \frac{4 \dot{m}}{\pi D_i \mu} = \frac{4 \times 2461.4}{\pi \times 0.08542 \times 4.104} = \frac{9845.6}{1.1014} = 8939 \approx 8940 Re D = π D i μ 4 m ˙ = π × 0.08542 × 4.104 4 × 2461.4 = 1.1014 9845.6 = 8939 ≈ 8940
Because Re D ≈ 8940 \text{Re}_D \approx 8940 Re D ≈ 8940 is within the turbulent range ( ≥ 10 , 000 \,\ge 10,000 ≥ 10 , 000 for standard handbook Dittus-Boelter application; transition-turbulent), apply Dittus-Boelter:
Step 3: Calculate Nusselt number via Dittus-Boelter Since fluid is being heated ( T s > T b T_s > T_b T s > T b ), n = 0.4 n = 0.4 n = 0.4 : Nu D = 0.023 Re D 0.8 Pr 0.4 = 0.023 × ( 8940 ) 0.8 × ( 3.01 ) 0.4 \text{Nu}_D = 0.023 \text{Re}_D^{0.8} \text{Pr}^{0.4} = 0.023 \times (8940)^{0.8} \times (3.01)^{0.4} Nu D = 0.023 Re D 0.8 Pr 0.4 = 0.023 × ( 8940 ) 0.8 × ( 3.01 ) 0.4 ( 8940 ) 0.8 = 1445.0 (8940)^{0.8} = 1445.0 ( 8940 ) 0.8 = 1445.0 ( 3.01 ) 0.4 = 1.5532 (3.01)^{0.4} = 1.5532 ( 3.01 ) 0.4 = 1.5532 Nu D = 0.023 × 1445.0 × 1.5532 = 51.62 \text{Nu}_D = 0.023 \times 1445.0 \times 1.5532 = 51.62 Nu D = 0.023 × 1445.0 × 1.5532 = 51.62
Step 4: Calculate convective heat transfer coefficient h i h_i h i h i = Nu D ⋅ k f D i = 51.62 × 0.376 Btu/(hr ⋅ ft ⋅ ∘ F) 0.08542 ft = 19.409 0.08542 = 227.2 Btu/(hr ⋅ ft 2 ⋅ ∘ F) h_i = \frac{\text{Nu}_D \cdot k_f}{D_i} = \frac{51.62 \times 0.376\text{ Btu/(hr}\cdot\text{ft}\cdot{}^\circ\text{F)}}{0.08542\text{ ft}} = \frac{19.409}{0.08542} = 227.2\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} h i = D i Nu D ⋅ k f = 0.08542 ft 51.62 × 0.376 Btu/(hr ⋅ ft ⋅ ∘ F) = 0.08542 19.409 = 227.2 Btu/(hr ⋅ ft 2 ⋅ ∘ F)
Step 5: Calculate convective heat transfer rate per linear foot Inside surface area per linear foot ( L = 1 ft L = 1\text{ ft} L = 1 ft ): A i ′ = π D i L = π × 0.08542 ft × 1.0 ft = 0.26836 ft 2 / ft A_i' = \pi D_i L = \pi \times 0.08542\text{ ft} \times 1.0\text{ ft} = 0.26836\text{ ft}^2/\text{ft} A i ′ = π D i L = π × 0.08542 ft × 1.0 ft = 0.26836 ft 2 / ft q ˙ ′ = h i A i ′ ( T s − T b ) = 227.2 × 0.26836 × ( 160.0 − 140.0 ) = 227.2 × 0.26836 × 20.0 = 1219.4 Btu/(hr ⋅ ft) \dot{q}' = h_i A_i' (T_s - T_b) = 227.2 \times 0.26836 \times (160.0 - 140.0) = 227.2 \times 0.26836 \times 20.0 = 1219.4\text{ Btu/(hr}\cdot\text{ft)} q ˙ ′ = h i A i ′ ( T s − T b ) = 227.2 × 0.26836 × ( 160.0 − 140.0 ) = 227.2 × 0.26836 × 20.0 = 1219.4 Btu/(hr ⋅ ft)