Study guide
4.3 Radiation Heat Transfer, Surface Emissivity & View Factors
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
4.3 Radiation Heat Transfer, Surface Emissivity & View Factors
Key Takeaways Explain This Topic AI
Stefan-Boltzmann Law establishes the maximum emissive power of a blackbody: E b = σ T 4 E_b = \sigma T^4 E b = σ T 4 , where σ = 0.1714 × 10 − 8 Btu/(hr ⋅ ft 2 ⋅ ∘ R 4 ) = 5.670 × 10 − 8 W/(m 2 ⋅ K 4 ) \sigma = 0.1714 \times 10^{-8}\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{R}^4) = 5.670 \times 10^{-8}\text{ W/(m}^2\cdot\text{K}^4) σ = 0.1714 × 1 0 − 8 Btu/(hr ⋅ ft 2 ⋅ ∘ R 4 ) = 5.670 × 1 0 − 8 W/(m 2 ⋅ K 4 ) , strictly requiring absolute temperature ( ∘ R = ∘ F + 459.67 {}^\circ\text{R} = {}^\circ\text{F} + 459.67 ∘ R = ∘ F + 459.67 ).
Wien's Displacement Law dictates the peak radiation wavelength: λ m a x T = 5193 μ m ⋅ ∘ R = 2898 μ m ⋅ K \lambda_{max} T = 5193\text{ }\mu\text{m}\cdot{}^\circ\text{R} = 2898\text{ }\mu\text{m}\cdot\text{K} λ ma x T = 5193 μ m ⋅ ∘ R = 2898 μ m ⋅ K , explaining why solar radiation is shortwave ( 0.5 μ m ~0.5\text{ }\mu\text{m} 0.5 μ m ) while terrestrial building radiation is longwave infrared ( 9.7 μ m ~9.7\text{ }\mu\text{m} 9.7 μ m ).
View factors ( F 12 F_{12} F 12 ) satisfy reciprocity ( A 1 F 12 = A 2 F 21 A_1 F_{12} = A_2 F_{21} A 1 F 12 = A 2 F 21 ) and enclosure summation ( ∑ j = 1 N F i j = 1 \sum_{j=1}^N F_{ij} = 1 ∑ j = 1 N F ij = 1 ); for a small convex object in a large enclosure, F 12 = 1.0 F_{12} = 1.0 F 12 = 1.0 .
Net radiative heat exchange between two infinite parallel gray surfaces is q ˙ 12 = σ A ( T 1 4 − T 2 4 ) 1 ε 1 + 1 ε 2 − 1 \dot{q}_{12} = \frac{\sigma A (T_1^4 - T_2^4)}{\frac{1}{\varepsilon_1} + \frac{1}{\varepsilon_2} - 1} q ˙ 12 = ε 1 1 + ε 2 1 − 1 σ A ( T 1 4 − T 2 4 ) ; adding N N N radiation shields of equal emissivity reduces heat transfer by 1 N + 1 \frac{1}{N + 1} N + 1 1 .
For combined convection and radiation, the linearized radiation coefficient is h r ≈ 4 ε σ T a v g 3 h_r \approx 4 \varepsilon \sigma T_{avg}^3 h r ≈ 4 ε σ T a vg 3 , allowing total surface heat transfer q = ( h c + h r ) A ( T s − T ∞ ) q = (h_c + h_r) A (T_s - T_\infty) q = ( h c + h r ) A ( T s − T ∞ ) .
Last updated: August 2026
4.3 Radiation Heat Transfer, Surface Emissivity & View Factors
Thermal radiation is the emission of energy in the form of electromagnetic waves (photons) emitted by all matter having a temperature above absolute zero. Unlike conduction and convection, thermal radiation requires no intervening physical medium and transmits most efficiently through a vacuum. In HVAC engineering, radiation governs cooling and heating load calculations through solar heat gains, interior surface radiative exchange between walls and occupants, uninsulated steam/chilled pipe heat losses, attic radiant barriers, and low-emissivity (Low-e) window coatings.
1. Fundamental Laws of Blackbody Thermal Radiation
Thermal radiation occupies the electromagnetic spectrum between wavelengths of λ = 0.1 μ m \lambda = 0.1\text{ }\mu\text{m} λ = 0.1 μ m and 100 μ m 100\text{ }\mu\text{m} 100 μ m , encompassing ultraviolet ( 0.1 − 0.4 μ m 0.1-0.4\text{ }\mu\text{m} 0.1 − 0.4 μ m ), visible light ( 0.4 − 0.7 μ m 0.4-0.7\text{ }\mu\text{m} 0.4 − 0.7 μ m ), and infrared ( 0.7 − 100 μ m 0.7-100\text{ }\mu\text{m} 0.7 − 100 μ m ). +-----------------------------------------------------------------------------------------+
- | THERMAL RADIATION IN THE ELECTROMAGNETIC SPECTRUM |
- +-----------------------------------------------------------------------------------------+
- | Ultraviolet | Visible Spectrum | Infrared (Thermal) |
- | 0.1 - 0.4 um | 0.4 - 0.7 um | 0.7 - 100 um |
- | | | Near-IR | Mid-IR | Far-IR (Longwave) |
- | | | 0.7-3.0 um | 3.0-50 um | 50-100 um |
- +-----------------------------------------------------------------------------------------+
- 1. Stefan-Boltzmann Law
A blackbody is an idealized thermodynamic body that absorbs all incident radiation (absorptivity α = 1.0 \alpha = 1.0 α = 1.0 ) and emits the maximum possible energy at every wavelength for a given temperature. The total hemispherical emissive power of a blackbody ( E b E_b E b ) is proportional to the fourth power of its absolute temperature: E b = σ T 4 E_b = \sigma T^4 E b = σ T 4
Where:
E b = blackbody emissive power ( Btu/(hr ⋅ ft 2 ) or W/m 2 ) E_b = \text{blackbody emissive power } (\text{Btu/(hr}\cdot\text{ft}^2) \text{ or W/m}^2) E b = blackbody emissive power ( Btu/(hr ⋅ ft 2 ) or W/m 2 )
T = absolute thermodynamic temperature in degrees Rankine ( ∘ R = ∘ F + 459.67 ) or Kelvin ( K = ∘ C + 273.15 ) T = \text{absolute thermodynamic temperature in degrees Rankine } ({}^\circ\text{R} = {}^\circ\text{F} + 459.67) \text{ or Kelvin } (\text{K} = {}^\circ\text{C} + 273.15) T = absolute thermodynamic temperature in degrees Rankine ( ∘ R = ∘ F + 459.67 ) or Kelvin ( K = ∘ C + 273.15 )
σ = Stefan-Boltzmann constant \sigma = \text{Stefan-Boltzmann constant} σ = Stefan-Boltzmann constant : σ = 0.1714 × 10 − 8 [ Btu hr ⋅ ft 2 ⋅ ∘ R 4 ] = 5.670 × 10 − 8 [ W m 2 ⋅ K 4 ] \sigma = 0.1714 \times 10^{-8} \quad \left[\frac{\text{Btu}}{\text{hr}\cdot\text{ft}^2\cdot{}^\circ\text{R}^4}\right] = 5.670 \times 10^{-8} \quad \left[\frac{\text{W}}{\text{m}^2\cdot\text{K}^4}\right] σ = 0.1714 × 1 0 − 8 [ hr ⋅ ft 2 ⋅ ∘ R 4 Btu ] = 5.670 × 1 0 − 8 [ m 2 ⋅ K 4 W ]
Exam Trap — Temperature Scale: Always convert temperatures to absolute units ( ∘ R {}^\circ\text{R} ∘ R or K \text{K} K ) before evaluating fourth-power radiation formulas. ( T 1 − T 2 ) 4 ≠ T 1 4 − T 2 4 (T_1 - T_2)^4 \neq T_1^4 - T_2^4 ( T 1 − T 2 ) 4 = T 1 4 − T 2 4 . Evaluating ( 200 − 70 ) 4 (200 - 70)^4 ( 200 − 70 ) 4 instead of ( 659.67 4 − 529.67 4 ) (659.67^4 - 529.67^4) ( 659.6 7 4 − 529.6 7 4 ) results in a catastrophic error.
2. Wien's Displacement Law
The wavelength λ m a x \lambda_{max} λ ma x at which blackbody monochromatic spectral emissive power ( E b λ E_{b\lambda} E bλ ) reaches its peak is inversely proportional to absolute temperature: λ m a x T = 5193 μ m ⋅ ∘ R = 2898 μ m ⋅ K \lambda_{max} T = 5193\text{ }\mu\text{m}\cdot{}^\circ\text{R} = 2898\text{ }\mu\text{m}\cdot\text{K} λ ma x T = 5193 μ m ⋅ ∘ R = 2898 μ m ⋅ K
Solar Radiation: The sun's surface temperature is T s u n ≈ 10 , 400 ∘ R T_{sun} \approx 10,400^\circ\text{R} T s u n ≈ 10 , 40 0 ∘ R ( 5778 K 5778\text{ K} 5778 K ), resulting in λ m a x = 2898 / 5778 ≈ 0.50 μ m \lambda_{max} = 2898 / 5778 \approx 0.50\text{ }\mu\text{m} λ ma x = 2898/5778 ≈ 0.50 μ m (peak in the visible light band).
Terrestrial & Building Surfaces: Building walls and piping at 70 ∘ F 70^\circ\text{F} 7 0 ∘ F ( 529.67 ∘ R = 294.3 K 529.67^\circ\text{R} = 294.3\text{ K} 529.6 7 ∘ R = 294.3 K ) have λ m a x = 2898 / 294.3 ≈ 9.85 μ m \lambda_{max} = 2898 / 294.3 \approx 9.85\text{ }\mu\text{m} λ ma x = 2898/294.3 ≈ 9.85 μ m (far-infrared, longwave thermal radiation).
2. Real Surface Properties: Emissivity, Absorptivity & Low-e Technology
Real surfaces emit and absorb less radiation than an ideal blackbody at the same temperature. +-----------------------------------------------------------------------------------------+
- | RADIATION ENERGY BALANCE AT A SURFACE BOUNDARY |
- +-----------------------------------------------------------------------------------------+
- | Incident Radiation (Irradiation G) ---------------------> |
- | | |
- | +---> Reflected: rho * G (Reflectivity) |
- | | |
- | +---> Absorbed: alpha * G (Absorptivity) |
- | | |
- | +---> Transmitted: tau * G (Transmissivity) |
- | |
- | Conservation of Energy: alpha + rho + tau = 1.0 (For Opaque Surfaces: alpha + rho = 1) |
- +-----------------------------------------------------------------------------------------+
- Definitions of Surface Radiative Properties
Emissivity ( ε \varepsilon ε ): Ratio of total radiation emitted by a real surface to that emitted by a blackbody at the same temperature ( 0 ≤ ε ≤ 1.0 0 \le \varepsilon \le 1.0 0 ≤ ε ≤ 1.0 ): E = ε E b = ε σ T 4 E = \varepsilon E_b = \varepsilon \sigma T^4 E = ε E b = ε σ T 4
Absorptivity ( α \alpha α ): Fraction of incident irradiation G G G absorbed by the surface ( 0 ≤ α ≤ 1.0 0 \le \alpha \le 1.0 0 ≤ α ≤ 1.0 ).
Reflectivity ( ρ \rho ρ ): Fraction of incident irradiation reflected by the surface ( 0 ≤ ρ ≤ 1.0 0 \le \rho \le 1.0 0 ≤ ρ ≤ 1.0 ).
Transmissivity ( τ \tau τ ): Fraction of incident irradiation transmitted through the medium ( 0 ≤ τ ≤ 1.0 0 \le \tau \le 1.0 0 ≤ τ ≤ 1.0 ).
For any surface, energy conservation dictates: α + ρ + τ = 1.0 \alpha + \rho + \tau = 1.0 α + ρ + τ = 1.0
For opaque bodies (building walls, metals, unglazed surfaces, τ = 0 \tau = 0 τ = 0 ): α + ρ = 1.0 ⟹ ρ = 1.0 − α \alpha + \rho = 1.0 \implies \rho = 1.0 - \alpha α + ρ = 1.0 ⟹ ρ = 1.0 − α
Kirchhoff's Law & Gray-Diffuse Surface Approximation
Under thermodynamic equilibrium, directional spectral emissivity equals directional spectral absorptivity. For a gray and diffuse surface (where radiative properties are independent of wavelength λ \lambda λ and emission angle θ \theta θ over the thermal spectrum): ε = α \varepsilon = \alpha ε = α
Low-Emissivity (Low-e) Coatings & Selective Surfaces
Building window glazings utilize microscopically thin silver or metal oxide coatings designed as spectrally selective surfaces :
High Shortwave Transmittance: Transmits visible solar radiation ( τ s o l ≈ 0.70 − 0.80 \tau_{sol} \approx 0.70-0.80 τ so l ≈ 0.70 − 0.80 ) to provide daylighting and winter passive solar gain.
Low Longwave Emissivity: Reflects longwave infrared radiation emitted by indoor furnishings and heating equipment ( ε g l a s s ≈ 0.04 \,\varepsilon_{glass} \approx 0.04 ε g l a ss ≈ 0.04 vs standard uncoated glass ε = 0.84 \varepsilon = 0.84 ε = 0.84 ), reducing radiant heat loss by over 90 % 90\% 90% through the glazing cavity.
Loading diagram... Low-e Glazing Longwave Radiation Reflection
3. Radiation View Factors (Shape / Configuration Factors)
The view factor F i j F_{ij} F ij (also called shape factor or configuration factor) is defined as the fraction of diffuse radiation leaving surface i i i that directly intercepts surface j j j : F i j = q ˙ i → j A i E b , i F_{ij} = \frac{\dot{q}_{i \to j}}{A_i E_{b,i}} F ij = A i E b , i q ˙ i → j +-----------------------------------------------------------------------------------------+
- | RADIATION VIEW FACTOR FUNDAMENTAL RULES |
- +-----------------------------------------------------------------------------------------+
- | 1. Reciprocity Theorem: A_1 * F_12 = A_2 * F_21 |
- | 2. Enclosure Summation Rule: Sum_{j=1}^N F_ij = 1.0 (for an N-surface enclosure) |
- | 3. Flat / Convex Surface: F_ii = 0 (A flat or convex surface cannot see itself) |
- | 4. Concave Surface: F_ii > 0 (A concave cavity sees part of its own surface) |
- | 5. Superposition Rule: F_1(2+3) = F_12 + F_13 |
- +-----------------------------------------------------------------------------------------+
- Fundamental View Factor Relationships
Reciprocity Relation: Connects view factors between two surfaces of arbitrary areas A i A_i A i and A j A_j A j : A i F i j = A j F j i A_i F_{ij} = A_j F_{ji} A i F ij = A j F ji
Summation Rule for an Enclosure: For an enclosure consisting of N N N surfaces completely enclosing a volume: ∑ j = 1 N F i j = F i 1 + F i 2 + ⋯ + F i N = 1.0 \sum_{j=1}^N F_{ij} = F_{i1} + F_{i2} + \cdots + F_{iN} = 1.0 j = 1 ∑ N F ij = F i 1 + F i 2 + ⋯ + F i N = 1.0
Self-Viewing Factor:
- For a flat or convex surface: F i i = 0 F_{ii} = 0 F ii = 0
- For a concave surface: F i i > 0 F_{ii} > 0 F ii > 0
- Common Analytical View Factors
Small Convex Object 1 Completely Enclosed by Large Enclosure 2: F 12 = 1.0 ⟹ F 21 = A 1 A 2 F 12 = A 1 A 2 , F 22 = 1 − A 1 A 2 F_{12} = 1.0 \quad \implies \quad F_{21} = \frac{A_1}{A_2} F_{12} = \frac{A_1}{A_2}, \quad F_{22} = 1 - \frac{A_1}{A_2} F 12 = 1.0 ⟹ F 21 = A 2 A 1 F 12 = A 2 A 1 , F 22 = 1 − A 2 A 1
Two Concentric Cylinders (Inner 1, Outer 2): F 12 = 1.0 , F 21 = r 1 r 2 , F 22 = 1 − r 1 r 2 F_{12} = 1.0, \quad F_{21} = \frac{r_1}{r_2}, \quad F_{22} = 1 - \frac{r_1}{r_2} F 12 = 1.0 , F 21 = r 2 r 1 , F 22 = 1 − r 2 r 1
Two Infinite Parallel Plates: F 12 = 1.0 , F 21 = 1.0 F_{12} = 1.0, \quad F_{21} = 1.0 F 12 = 1.0 , F 21 = 1.0
- 4. Radiative Heat Exchange Between Gray Diffuse Surfaces
- 1. Small Convex Surface 1 in a Large Enclosure 2
For an uninsulated pipe, duct, or human occupant (surface area A 1 A_1 A 1 , emissivity ε 1 \varepsilon_1 ε 1 , temperature T 1 T_1 T 1 ) located inside a large room (enclosure area A 2 ≫ A 1 A_2 \gg A_1 A 2 ≫ A 1 , wall temperature T 2 T_2 T 2 ): q ˙ 12 = ε 1 σ A 1 ( T 1 4 − T 2 4 ) \dot{q}_{12} = \varepsilon_1 \sigma A_1 (T_1^4 - T_2^4) q ˙ 12 = ε 1 σ A 1 ( T 1 4 − T 2 4 )
Notice that the emissivity of the large room enclosure ( ε 2 \varepsilon_2 ε 2 ) has zero effect on the net exchange because the room acts as a blackbody cavity ( A 1 / A 2 → 0 A_1/A_2 \to 0 A 1 / A 2 → 0 ).
2. Two Large Infinite Parallel Gray Plates
For radiant heat transfer across an air gap between two parallel sheets of area A A A with emissivities ε 1 \varepsilon_1 ε 1 and ε 2 \varepsilon_2 ε 2 : q ˙ 12 = σ A ( T 1 4 − T 2 4 ) 1 ε 1 + 1 ε 2 − 1 \dot{q}_{12} = \frac{\sigma A (T_1^4 - T_2^4)}{\frac{1}{\varepsilon_1} + \frac{1}{\varepsilon_2} - 1} q ˙ 12 = ε 1 1 + ε 2 1 − 1 σ A ( T 1 4 − T 2 4 )
3. Long Concentric Cylinders (Insulated Pipe in Concentric Sleeve)
For inner cylinder 1 (radius r 1 r_1 r 1 ) and outer cylinder 2 (radius r 2 r_2 r 2 ): q ˙ 12 = σ A 1 ( T 1 4 − T 2 4 ) 1 ε 1 + ( 1 − ε 2 ε 2 ) ( r 1 r 2 ) \dot{q}_{12} = \frac{\sigma A_1 (T_1^4 - T_2^4)}{\frac{1}{\varepsilon_1} + \left(\frac{1 - \varepsilon_2}{\varepsilon_2}\right)\left(\frac{r_1}{r_2}\right)} q ˙ 12 = ε 1 1 + ( ε 2 1 − ε 2 ) ( r 2 r 1 ) σ A 1 ( T 1 4 − T 2 4 )
4. Radiation Shields
Thin, highly reflective sheets (such as polished aluminum foil, ε s ≈ 0.05 \varepsilon_s \approx 0.05 ε s ≈ 0.05 ) placed between two radiating surfaces act as radiation shields to drastically reduce net radiative exchange. +-----------------------------------------------------------------------------------------+
- | EFFECT OF N RADIATION SHIELDS BETWEEN PARALLEL PLATES |
- +-----------------------------------------------------------------------------------------+
- | Plate 1 (T_1, e_1) | Shield 1 | Shield 2 | ... | Shield N | Plate 2 (T_2, e_2) |
- | |
- | When all surfaces have identical emissivity (e_1 = e_2 = e_s): |
- | |
- | q_with_shields = [ 1 / (N + 1) ] * q_without_shields |
- +-----------------------------------------------------------------------------------------+
For N N N parallel radiation shields placed between two large parallel plates, where all surfaces have identical emissivity ε \varepsilon ε : q ˙ w i t h N s h i e l d s = 1 N + 1 q ˙ n o s h i e l d s \dot{q}_{with\text{ }N\text{ }shields} = \frac{1}{N + 1} \dot{q}_{no\text{ }shields} q ˙ w i t h N s hi e l d s = N + 1 1 q ˙ n o s hi e l d s
5. Linearized Radiation Heat Transfer Coefficient ( h r h_r h r )
In HVAC cooling and heating load calculations, radiative and convective heat exchanges occur simultaneously from the same surface. Factoring the fourth-power temperature difference ( T 1 4 − T 2 4 ) (T_1^4 - T_2^4) ( T 1 4 − T 2 4 ) : ( T 1 4 − T 2 4 ) = ( T 1 2 − T 2 2 ) ( T 1 2 + T 2 2 ) = ( T 1 − T 2 ) ( T 1 + T 2 ) ( T 1 2 + T 2 2 ) (T_1^4 - T_2^4) = (T_1^2 - T_2^2)(T_1^2 + T_2^2) = (T_1 - T_2)(T_1 + T_2)(T_1^2 + T_2^2) ( T 1 4 − T 2 4 ) = ( T 1 2 − T 2 2 ) ( T 1 2 + T 2 2 ) = ( T 1 − T 2 ) ( T 1 + T 2 ) ( T 1 2 + T 2 2 )
Substituting into the net radiation equation for a small body in a large enclosure: q ˙ r a d = ε 1 σ A 1 ( T 1 4 − T 2 4 ) = [ ε 1 σ ( T 1 + T 2 ) ( T 1 2 + T 2 2 ) ] A 1 ( T 1 − T 2 ) = h r A 1 ( T 1 − T 2 ) \dot{q}_{rad} = \varepsilon_1 \sigma A_1 (T_1^4 - T_2^4) = \left[\varepsilon_1 \sigma (T_1 + T_2)(T_1^2 + T_2^2)\right] A_1 (T_1 - T_2) = h_r A_1 (T_1 - T_2) q ˙ r a d = ε 1 σ A 1 ( T 1 4 − T 2 4 ) = [ ε 1 σ ( T 1 + T 2 ) ( T 1 2 + T 2 2 ) ] A 1 ( T 1 − T 2 ) = h r A 1 ( T 1 − T 2 )
Where the linearized radiation coefficient is: h r = ε 1 σ ( T 1 + T 2 ) ( T 1 2 + T 2 2 ) ≈ 4 ε 1 σ T a v g 3 h_r = \varepsilon_1 \sigma (T_1 + T_2)(T_1^2 + T_2^2) \approx 4 \varepsilon_1 \sigma T_{avg}^3 h r = ε 1 σ ( T 1 + T 2 ) ( T 1 2 + T 2 2 ) ≈ 4 ε 1 σ T a vg 3
Where T a v g = T 1 + T 2 2 T_{avg} = \frac{T_1 + T_2}{2} T a vg = 2 T 1 + T 2 in absolute temperature ( ∘ R {}^\circ\text{R} ∘ R or K \text{K} K ).
Combined Heat Transfer Coefficient ( h t o t a l h_{total} h t o t a l )
When ambient air temperature equals surrounding wall temperature ( T ∞ = T s u r r T_\infty = T_{surr} T ∞ = T s u rr ): q ˙ t o t a l = q ˙ c o n v + q ˙ r a d = h c A ( T s − T ∞ ) + h r A ( T s − T ∞ ) = ( h c + h r ) A ( T s − T ∞ ) = h t o t a l A ( T s − T ∞ ) \dot{q}_{total} = \dot{q}_{conv} + \dot{q}_{rad} = h_c A (T_s - T_\infty) + h_r A (T_s - T_\infty) = (h_c + h_r) A (T_s - T_\infty) = h_{total} A (T_s - T_\infty) q ˙ t o t a l = q ˙ co n v + q ˙ r a d = h c A ( T s − T ∞ ) + h r A ( T s − T ∞ ) = ( h c + h r ) A ( T s − T ∞ ) = h t o t a l A ( T s − T ∞ ) h t o t a l = h c + h r h_{total} = h_c + h_r h t o t a l = h c + h r
- 6. Step-by-Step Worked Example: Uninsulated Steam Pipe Heat Loss
- Problem Statement
An uninsulated horizontal steel steam pipe ( 4.50 -in. 4.50\text{-in.} 4.50 -in. outer diameter, D o = 0.375 ft D_o = 0.375\text{ ft} D o = 0.375 ft , length L = 50.0 ft L = 50.0\text{ ft} L = 50.0 ft ) passes through an open mechanical equipment room. The pipe outer surface is at T s = 250.0 ∘ F T_s = 250.0^\circ\text{F} T s = 250. 0 ∘ F and has an emissivity of ε = 0.80 \varepsilon = 0.80 ε = 0.80 . The mechanical room walls and surrounding air are at T ∞ = T w a l l s = 70.0 ∘ F T_\infty = T_{walls} = 70.0^\circ\text{F} T ∞ = T w a ll s = 70. 0 ∘ F . The natural convection coefficient from the horizontal pipe is h c = 1.25 Btu/(hr ⋅ ft 2 ⋅ ∘ F) h_c = 1.25\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} h c = 1.25 Btu/(hr ⋅ ft 2 ⋅ ∘ F) .
Calculate:
Outer surface area of the pipe A s A_s A s ( ft 2 \text{ft}^2 ft 2 )
Steady-state convective heat loss rate q ˙ c o n v \dot{q}_{conv} q ˙ co n v ( Btu/hr \text{Btu/hr} Btu/hr )
- Steady-state radiative heat loss rate q ˙ r a d \dot{q}_{rad} q ˙ r a d ( Btu/hr \text{Btu/hr} Btu/hr )
- Linearized radiation coefficient h r h_r h r and combined coefficient h t o t a l h_{total} h t o t a l
- Total heat loss rate q ˙ t o t a l \dot{q}_{total} q ˙ t o t a l ( Btu/hr \text{Btu/hr} Btu/hr )
- Solution Steps
Step 1: Calculate outer pipe surface area A s = π D o L = π × 0.375 ft × 50.0 ft = 58.905 ft 2 A_s = \pi D_o L = \pi \times 0.375\text{ ft} \times 50.0\text{ ft} = 58.905\text{ ft}^2 A s = π D o L = π × 0.375 ft × 50.0 ft = 58.905 ft 2
Step 2: Calculate convective heat loss Δ T = T s − T ∞ = 250.0 ∘ F − 70.0 ∘ F = 180.0 ∘ F \Delta T = T_s - T_\infty = 250.0^\circ\text{F} - 70.0^\circ\text{F} = 180.0^\circ\text{F} Δ T = T s − T ∞ = 250. 0 ∘ F − 70. 0 ∘ F = 180. 0 ∘ F q ˙ c o n v = h c A s Δ T = 1.25 Btu/(hr ⋅ ft 2 ⋅ ∘ F) × 58.905 ft 2 × 180.0 ∘ F = 13 , 253.6 Btu/hr \dot{q}_{conv} = h_c A_s \Delta T = 1.25\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} \times 58.905\text{ ft}^2 \times 180.0^\circ\text{F} = 13,253.6\text{ Btu/hr} q ˙ co n v = h c A s Δ T = 1.25 Btu/(hr ⋅ ft 2 ⋅ ∘ F) × 58.905 ft 2 × 180. 0 ∘ F = 13 , 253.6 Btu/hr
Step 3: Calculate radiative heat loss using absolute Rankine temperatures T s = 250.0 + 459.67 = 709.67 ∘ R T_s = 250.0 + 459.67 = 709.67^\circ\text{R} T s = 250.0 + 459.67 = 709.6 7 ∘ R T w a l l s = 70.0 + 459.67 = 529.67 ∘ R T_{walls} = 70.0 + 459.67 = 529.67^\circ\text{R} T w a ll s = 70.0 + 459.67 = 529.6 7 ∘ R T s 4 = ( 709.67 ) 4 = 2.5364 × 10 11 ∘ R 4 T_s^4 = (709.67)^4 = 2.5364 \times 10^{11}\text{ }{}^\circ\text{R}^4 T s 4 = ( 709.67 ) 4 = 2.5364 × 1 0 11 ∘ R 4 T w a l l s 4 = ( 529.67 ) 4 = 7.8709 × 10 10 ∘ R 4 T_{walls}^4 = (529.67)^4 = 7.8709 \times 10^{10}\text{ }{}^\circ\text{R}^4 T w a ll s 4 = ( 529.67 ) 4 = 7.8709 × 1 0 10 ∘ R 4 T s 4 − T w a l l s 4 = 2.5364 × 10 11 − 0.7871 × 10 11 = 1.7493 × 10 11 ∘ R 4 T_s^4 - T_{walls}^4 = 2.5364 \times 10^{11} - 0.7871 \times 10^{11} = 1.7493 \times 10^{11}\text{ }{}^\circ\text{R}^4 T s 4 − T w a ll s 4 = 2.5364 × 1 0 11 − 0.7871 × 1 0 11 = 1.7493 × 1 0 11 ∘ R 4 q ˙ r a d = ε σ A s ( T s 4 − T w a l l s 4 ) \dot{q}_{rad} = \varepsilon \sigma A_s (T_s^4 - T_{walls}^4) q ˙ r a d = ε σ A s ( T s 4 − T w a ll s 4 ) q ˙ r a d = 0.80 × ( 0.1714 × 10 − 8 ) × 58.905 × ( 1.7493 × 10 11 ) \dot{q}_{rad} = 0.80 \times (0.1714 \times 10^{-8}) \times 58.905 \times (1.7493 \times 10^{11}) q ˙ r a d = 0.80 × ( 0.1714 × 1 0 − 8 ) × 58.905 × ( 1.7493 × 1 0 11 ) q ˙ r a d = 0.80 × 0.1714 × 58.905 × 174.93 = 14 , 131.5 Btu/hr \dot{q}_{rad} = 0.80 \times 0.1714 \times 58.905 \times 174.93 = 14,131.5\text{ Btu/hr} q ˙ r a d = 0.80 × 0.1714 × 58.905 × 174.93 = 14 , 131.5 Btu/hr
Step 4: Calculate linearized radiation coefficient h r h_r h r and combined h t o t a l h_{total} h t o t a l h r = q ˙ r a d A s ( T s − T w a l l s ) = 14 , 131.5 Btu/hr 58.905 ft 2 × 180.0 ∘ F = 1.333 Btu/(hr ⋅ ft 2 ⋅ ∘ F) h_r = \frac{\dot{q}_{rad}}{A_s (T_s - T_{walls})} = \frac{14,131.5\text{ Btu/hr}}{58.905\text{ ft}^2 \times 180.0^\circ\text{F}} = 1.333\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} h r = A s ( T s − T w a ll s ) q ˙ r a d = 58.905 ft 2 × 180. 0 ∘ F 14 , 131.5 Btu/hr = 1.333 Btu/(hr ⋅ ft 2 ⋅ ∘ F) h t o t a l = h c + h r = 1.25 + 1.333 = 2.583 Btu/(hr ⋅ ft 2 ⋅ ∘ F) h_{total} = h_c + h_r = 1.25 + 1.333 = 2.583\text{ Btu/(hr}\cdot\text{ft}^2\cdot{}^\circ\text{F)} h t o t a l = h c + h r = 1.25 + 1.333 = 2.583 Btu/(hr ⋅ ft 2 ⋅ ∘ F)
Step 5: Calculate total heat loss rate q ˙ t o t a l = q ˙ c o n v + q ˙ r a d = 13 , 253.6 + 14 , 131.5 = 27 , 385.1 Btu/hr \dot{q}_{total} = \dot{q}_{conv} + \dot{q}_{rad} = 13,253.6 + 14,131.5 = 27,385.1\text{ Btu/hr} q ˙ t o t a l = q ˙ co n v + q ˙ r a d = 13 , 253.6 + 14 , 131.5 = 27 , 385.1 Btu/hr
Note that radiation accounts for over 51.6 % 51.6\% 51.6% of the total heat dissipation, proving that radiant heat exchange cannot be neglected in uninsulated high-temperature piping.