Study guide
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints)
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints)
Key Takeaways Explain This Topic AI
ASHRAE climatic design conditions establish cooling design dry-bulb temperatures based on annual cumulative frequency of occurrence percentiles (0.4%, 1.0%, and 2.0%), representing 35, 88, and 175 annual hours of exceedance out of 8,760 hours/year.
Heating design conditions represent extreme cold thresholds based on 99.6% and 99.0% annual percentiles, corresponding to 35 and 88 hours per year where ambient dry-bulb temperatures fall below the design value.
Dehumidification and dedicated outdoor air systems (DOAS) must be sized using peak dew-point temperature and mean coincident dry-bulb (MCDB) conditions or peak wet-bulb conditions, rather than peak dry-bulb conditions.
Indoor design setpoints follow ASHRAE Standard 55-2023 thermal comfort criteria, establishing operative temperatures between 75°F and 78°F at 50% relative humidity for summer cooling and 68°F to 72°F for winter heating, with a maximum humidity ceiling of 0.012 lb_w/lb_da (60% RH / 62.2°F dew point).
Atmospheric pressure decreases with altitude, derating standard air density (0.075 lbm/ft³) and requiring non-standard sensible (C_s = 14.4 * rho) and latent (C_l = 64,560 * rho) multipliers for HVAC psychrometric calculations.
Last updated: August 2026
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints)
Accurate heating and cooling load calculations form the foundation of all mechanical equipment sizing, psychrometric system analysis, and energy code compliance. System capacity is governed by the boundary conditions established between the external ambient environment and the controlled indoor occupied space. Oversizing equipment leads to short-cycling, elevated indoor humidity, premature component failure, and excessive capital expenditure; undersizing results in loss of space temperature and humidity control during peak weather events. The ASHRAE Handbook—Fundamentals provides statistically derived climatic design conditions for thousands of worldwide locations, establishing rigorous design baselines for the PE Mechanical: HVAC and Refrigeration examination.
1. ASHRAE Climatic Design Information & Frequency of Occurrence
Outdoor weather conditions fluctuate continuously throughout the year. Sizing HVAC equipment for the single most extreme historical temperature ever recorded at a weather station would result in massive, uneconomical overdesign. Instead, ASHRAE utilizes a statistical cumulative frequency of occurrence approach based on 30 years of hourly meteorological data spanning all 8 , 760 hours 8,760\text{ hours} 8 , 760 hours in a standard year. +---------------------------------------------------------------------------------------------------------+
- | ASHRAE CLIMATIC DESIGN PERCENTILE SPECTRUM (8,760 HOURS/YEAR) |
- +---------------------------------------------------------------------------------------------------------+
- | Heating Design (Coldest Occurrences) | Cooling Design (Warmest Occurrences) |
- | 99.6% Value -> 35.04 hours/yr below design | 0.4% Value -> 35.04 hours/yr exceeded (Critical / Hospitals)|
- | 99.0% Value -> 87.60 hours/yr below design | 1.0% Value -> 87.60 hours/yr exceeded (Standard Commercial) |
- | | 2.0% Value -> 175.20 hours/yr exceeded (Residential/Storage)|
- +---------------------------------------------------------------------------------------------------------+
- Annual Exceedance Hours Mathematical Derivation
The number of annual hours ( N exceed N_{\text{exceed}} N exceed ) that ambient weather conditions are expected to exceed (or fall below) a given design percentile is: N exceed = 8 , 760 hr/yr × ( Percentile 100 ) N_{\text{exceed}} = 8,760\text{ hr/yr} \times \left(\frac{\text{Percentile}}{100}\right) N exceed = 8 , 760 hr/yr × ( 100 Percentile )
0.4% Cooling Condition: N exceed = 8 , 760 × 0.004 = 35.04 hours/year N_{\text{exceed}} = 8,760 \times 0.004 = 35.04\text{ hours/year} N exceed = 8 , 760 × 0.004 = 35.04 hours/year .
1.0% Cooling Condition: N exceed = 8 , 760 × 0.010 = 87.60 hours/year N_{\text{exceed}} = 8,760 \times 0.010 = 87.60\text{ hours/year} N exceed = 8 , 760 × 0.010 = 87.60 hours/year .
2.0% Cooling Condition: N exceed = 8 , 760 × 0.020 = 175.20 hours/year N_{\text{exceed}} = 8,760 \times 0.020 = 175.20\text{ hours/year} N exceed = 8 , 760 × 0.020 = 175.20 hours/year .
99.6% Heating Condition: Extreme cold threshold where ambient dry-bulb temperature is below design for 8 , 760 × ( 1 − 0.996 ) = 35.04 hours/year 8,760 \times (1 - 0.996) = 35.04\text{ hours/year} 8 , 760 × ( 1 − 0.996 ) = 35.04 hours/year .
99.0% Heating Condition: Ambient temperature is below design for 8 , 760 × ( 1 − 0.990 ) = 87.60 hours/year 8,760 \times (1 - 0.990) = 87.60\text{ hours/year} 8 , 760 × ( 1 − 0.990 ) = 87.60 hours/year .
Application Guidelines for Design Percentiles
Design Condition Percentile Recommended Facility Type & Engineering Application
Cooling Dry-Bulb (DB) / MCWB 0.4% Hospitals, healthcare surgical suites, laboratories, data centers, cleanrooms, museums, and critical process manufacturing
Cooling Dry-Bulb (DB) / MCWB 1.0% Standard commercial office buildings, retail centers, educational classrooms, hotels, and general institutional spaces
Cooling Dry-Bulb (DB) / MCWB 2.0% Warehouses, light industrial storage, non-critical storage facilities, and low-cost residential construction
Heating Dry-Bulb (DB) 99.6% Critical healthcare facilities, uninsulated structures with high freeze susceptibility, critical process environments
- Heating Dry-Bulb (DB) 99.0% Standard commercial, institutional, and residential buildings
- 2. Coincident vs. Non-Coincident Climatic Parameters
Atmospheric moisture and sensible heat do not peak at the exact same hour of the day. A major source of error in load calculations is confusing coincident weather parameters with non-coincident peak values.
1. Peak Dry-Bulb Temperature with Mean Coincident Wet-Bulb (DB / MCWB)
Definition: The peak sensible ambient condition (e.g., 95 ∘ F 95^\circ\text{F} 9 5 ∘ F DB) paired with the average wet-bulb temperature observed concurrently during those peak dry-bulb hours (e.g., 75 ∘ F 75^\circ\text{F} 7 5 ∘ F MCWB).
Primary Use: Sizing standard sensible air conditioning systems, packaged rooftop units (RTUs), and sensible building envelope cooling components where solar radiation and conduction dominate.
2. Peak Dew-Point Temperature with Mean Coincident Dry-Bulb (DP / MCDB)
Definition: The peak moisture content condition in the outdoor air (e.g., 76 ∘ F 76^\circ\text{F} 7 6 ∘ F Dew Point paired with 82 ∘ F 82^\circ\text{F} 8 2 ∘ F MCDB).
Primary Use: Sizing Dedicated Outdoor Air Systems (DOAS) , 100% outdoor air handling units, dehumidification coils, and energy recovery ventilators (ERVs). Sizing a 100% outdoor air unit using peak dry-bulb conditions severely underestimates the latent cooling coil load, resulting in uncontrolled indoor relative humidity.
3. Peak Wet-Bulb Temperature (Non-Coincident WBT)
Definition: The maximum ambient wet-bulb temperature observed regardless of dry-bulb temperature.
Primary Use: Sizing evaporative heat rejection equipment , including cooling towers, evaporative fluid coolers, and evaporative condensers. +---------------------------------------------------------------------------------------------------------+
- | PSYCHROMETRIC IMPACT: PEAK SENSIBLE VS. PEAK LATENT DESIGN CONDITIONS |
- +---------------------------------------------------------------------------------------------------------+
- | Condition A (Peak DB / MCWB): 95°F DB / 75°F MCWB -> W = 0.0141 lb_w/lb_da -> h = 38.6 Btu/lb |
- | Condition B (Peak DP / MCDB): 82°F DB / 76°F DP -> W = 0.0195 lb_w/lb_da -> h = 42.4 Btu/lb |
- | *Notice that Condition B imposes 38% more latent moisture load (W) and higher total enthalpy (h)! |
- +---------------------------------------------------------------------------------------------------------+
- 3. Diurnal Temperature Variation & Daily Range
The Daily Range (DR) represents the mean difference between the maximum and minimum dry-bulb temperatures recorded on the design day during the warmest month: D R = T max − T min DR = T_{\text{max}} - T_{\text{min}} D R = T max − T min
High Daily Range ( D R > 25 ∘ F DR > 25^\circ\text{F} D R > 2 5 ∘ F ): Arid and high-elevation climates (e.g., Phoenix, AZ; Denver, CO; Las Vegas, NV). Significant night-time cooling allows night purge economizer cycles and high thermal mass effectiveness.
Medium Daily Range ( 16 ∘ F ≤ D R ≤ 25 ∘ F 16^\circ\text{F} \le DR \le 25^\circ\text{F} 1 6 ∘ F ≤ D R ≤ 2 5 ∘ F ): Inland continental climates (e.g., Chicago, IL; Atlanta, GA; Dallas, TX).
Low Daily Range ( D R < 16 ∘ F DR < 16^\circ\text{F} D R < 1 6 ∘ F ): Humid coastal and maritime regions (e.g., Miami, FL; Houston, TX; Honolulu, HI). Small ambient swings mean building envelope heat transfer remains elevated throughout the night.
The daily range directly modifies the Cooling Load Temperature Difference (CLTD) and sol-air temperature calculations through the average outdoor daily temperature ( T o , m T_{o,m} T o , m ): T o , m = T o , peak − D R 2 T_{o,m} = T_{o,\text{peak}} - \frac{DR}{2} T o , m = T o , peak − 2 D R
4. Indoor Thermal Comfort Setpoints & ASHRAE Standard 55-2023
ASHRAE Standard 55-2023 defines indoor thermal comfort based on six primary parameters: metabolic rate ( M M M ), clothing insulation ( I c l I_{cl} I c l ), air dry-bulb temperature ( T a T_a T a ), mean radiant temperature ( T ˉ r \bar{T}_r T ˉ r ), relative air velocity ( v v v ), and air humidity.
Operative Temperature ( T o T_o T o )
In spaces with low air velocities ( v < 40 FPM v < 40\text{ FPM} v < 40 FPM or 0.2 m/s 0.2\text{ m/s} 0.2 m/s ), the operative temperature is approximated as the arithmetic mean of air dry-bulb and mean radiant temperature: T o = T a + T ˉ r 2 T_o = \frac{T_a + \bar{T}_r}{2} T o = 2 T a + T ˉ r
Standard Design Setpoints for Load Calculations
Season / Application Indoor Dry-Bulb ( T i T_i T i ) Indoor Relative Humidity (RH) Maximum Dew Point / Humidity Ratio
Summer Cooling (Standard) 75 ∘ F to 78 ∘ F 75^\circ\text{F}\text{ to }78^\circ\text{F} 7 5 ∘ F to 7 8 ∘ F ( 24 ∘ C to 25.5 ∘ C 24^\circ\text{C}\text{ to }25.5^\circ\text{C} 2 4 ∘ C to 25. 5 ∘ C ) 50 % RH 50\%\text{ RH} 50% RH D P T ≤ 62.2 ∘ F DPT \le 62.2^\circ\text{F} D PT ≤ 62. 2 ∘ F ( W ≤ 0.012 lb w / lb d a W \le 0.012\text{ lb}_w/\text{lb}_{da} W ≤ 0.012 lb w / lb d a )
Summer Cooling (Data Centers) 64.4 ∘ F to 80.6 ∘ F 64.4^\circ\text{F}\text{ to }80.6^\circ\text{F} 64. 4 ∘ F to 80. 6 ∘ F (ASHRAE TC 9.9) 20 % to 60 % RH 20\%\text{ to }60\%\text{ RH} 20% to 60% RH D P T ≤ 59 ∘ F DPT \le 59^\circ\text{F} D PT ≤ 5 9 ∘ F ( 15 ∘ C 15^\circ\text{C} 1 5 ∘ C ), 60 grains/lb 60\text{ grains/lb} 60 grains/lb
Winter Heating (Standard) 68 ∘ F to 72 ∘ F 68^\circ\text{F}\text{ to }72^\circ\text{F} 6 8 ∘ F to 7 2 ∘ F ( 20 ∘ C to 22 ∘ C 20^\circ\text{C}\text{ to }22^\circ\text{C} 2 0 ∘ C to 2 2 ∘ C ) 30 % RH (if humidified) 30\%\text{ RH (if humidified)} 30% RH (if humidified) Minimum W ≥ 0.004 lb w / lb d a W \ge 0.004\text{ lb}_w/\text{lb}_{da} W ≥ 0.004 lb w / lb d a
Operating Rooms / Surgical 66 ∘ F to 68 ∘ F 66^\circ\text{F}\text{ to }68^\circ\text{F} 6 6 ∘ F to 6 8 ∘ F ( 19 ∘ C to 20 ∘ C 19^\circ\text{C}\text{ to }20^\circ\text{C} 1 9 ∘ C to 2 0 ∘ C ) 45 % to 55 % RH 45\%\text{ to }55\%\text{ RH} 45% to 55% RH Strict positive pressure ( + 0.01 to + 0.03 in. w.g. +0.01\text{ to }+0.03\text{ in. w.g.} + 0.01 to + 0.03 in. w.g. )
ASHRAE 55 & 62.1 Humidity Upper Limit: To prevent microbial growth, mold, and dust mite proliferation, ASHRAE Standard 62.1 mandates that occupied space relative humidity shall not exceed 60 % RH 60\%\text{ RH} 60% RH (corresponding to a maximum design dew point of 62.2 ∘ F 62.2^\circ\text{F} 62. 2 ∘ F or W = 0.012 lb w / lb d a = 84 grains/lb W = 0.012\text{ lb}_w/\text{lb}_{da} = 84\text{ grains/lb} W = 0.012 lb w / lb d a = 84 grains/lb ). Standard load sizing utilizes 75 ∘ F 75^\circ\text{F} 7 5 ∘ F DB and 50 % RH 50\%\text{ RH} 50% RH ( W = 0.00925 lb w / lb d a = 64.8 grains/lb W = 0.00925\text{ lb}_w/\text{lb}_{da} = 64.8\text{ grains/lb} W = 0.00925 lb w / lb d a = 64.8 grains/lb , h = 28.1 Btu/lb h = 28.1\text{ Btu/lb} h = 28.1 Btu/lb ). Sizing heating loads assumes zero indoor humidity generation and no solar/internal heat credit (conservative winter baseline).
5. Space Pressurization & Room Air Balance
Pressurization control prevents the infiltration of unconditioned, humid, or contaminated air across exterior envelope boundaries and interior partitions. +-----------------------------------------------------------------------------------------+
- | SPACE PRESSURIZATION & AIR BALANCE ARCHITECTURES |
- +-----------------------------------------------------------------------------------------+
- | Positive Pressure (+): Supply Air > (Return Air + Exhaust Air) -> Exfiltration |
- | - Applications: Operating Rooms, Cleanrooms, Pharmacy Compounding, Office Envelopes |
- | |
- | Negative Pressure (-): Supply Air < (Return Air + Exhaust Air) -> Infiltration |
- | - Applications: Isolation Rooms, Laboratories, Restrooms, Commercial Kitchens |
- +-----------------------------------------------------------------------------------------+
General Commercial Envelopes: Sized for net positive pressure ( + 0.02 to + 0.05 in. w.g. +0.02\text{ to }+0.05\text{ in. w.g.} + 0.02 to + 0.05 in. w.g. ) by introducing outdoor ventilation air equal to 105 % to 115 % 105\%\text{ to }115\% 105% to 115% of total building exhaust air, preventing untreated exterior infiltration.
Airborne Infection Isolation Rooms (AIIR): Maintained at negative pressure (minimum − 0.01 to − 0.03 in. w.g. -0.01\text{ to }-0.03\text{ in. w.g.} − 0.01 to − 0.03 in. w.g. or minimum 12 ACH 12\text{ ACH} 12 ACH ) to contain pathogens.
6. Barometric Pressure & Altitude Derating
Atmospheric pressure decreases with altitude, directly reducing air density ( ρ \rho ρ ). Sizing HVAC equipment at high elevations requires calculating local barometric pressure ( P P P ) and actual air density ( ρ actual \rho_{\text{actual}} ρ actual ).
ASHRAE Standard Atmosphere Altitude Formulation
For elevations up to 36 , 000 ft 36,000\text{ ft} 36 , 000 ft ( 11 , 000 m 11,000\text{ m} 11 , 000 m ), barometric pressure P P P in psia \text{psia} psia as a function of elevation Z Z Z in feet is: P = 14.696 × ( 1 − 6.8754 × 10 − 6 × Z ) 5.2559 P = 14.696 \times \left(1 - 6.8754 \times 10^{-6} \times Z\right)^{5.2559} P = 14.696 × ( 1 − 6.8754 × 1 0 − 6 × Z ) 5.2559
Actual air density ( ρ \rho ρ ) from the ideal gas law ( R da = 53.352 ft ⋅ lbf/(lbm ⋅ ∘ R) R_{\text{da}} = 53.352\text{ ft}\cdot\text{lbf/(lbm}\cdot{}^\circ\text{R)} R da = 53.352 ft ⋅ lbf/(lbm ⋅ ∘ R) ): ρ = 144 × P R da × T Rankine = 144 × P 53.352 × ( T ∘ F + 459.67 ) \rho = \frac{144 \times P}{R_{\text{da}} \times T_{\text{Rankine}}} = \frac{144 \times P}{53.352 \times (T_{^\circ\text{F}} + 459.67)} ρ = R da × T Rankine 144 × P = 53.352 × ( T ∘ F + 459.67 ) 144 × P
Impact on HVAC Shortcut Heat Multipliers
Elevation (ft) Barometric Pressure (psia) Air Density at 70°F (lbm/ft³) Sensible Constant ( C s = 60 ρ c p C_s = 60 \rho c_p C s = 60 ρ c p ) Latent Constant ( C l = 60 ρ h f g C_l = 60 \rho h_{fg} C l = 60 ρ h f g ) Total Constant ( C t = 60 ρ C_t = 60 \rho C t = 60 ρ )
- 0 (Sea Level) 14.696 14.696 14.696 0.0750 0.0750 0.0750 1.08 1.08 1.08 4840 4840 4840 4.50 4.50 4.50
- 2,000 13.664 13.664 13.664 0.0697 0.0697 0.0697 1.00 1.00 1.00 4500 4500 4500 4.18 4.18 4.18
5,000 (Denver) 12.228 12.228 12.228 0.0624 0.0624 0.0624 0.899 ≈ 0.90 0.899 \approx 0.90 0.899 ≈ 0.90 4025 4025 4025 3.74 3.74 3.74
8,000 10.914 10.914 10.914 0.0557 0.0557 0.0557 0.802 ≈ 0.80 0.802 \approx 0.80 0.802 ≈ 0.80 3595 3595 3595 3.34 3.34 3.34
Exam Strategy: Never use 1.08 1.08 1.08 on high-altitude exam questions without verifying whether volumetric flow ( CFM \text{CFM} CFM ) is specified in actual cubic feet per minute ( ACFM \text{ACFM} ACFM ) or standard cubic feet per minute ( SCFM \text{SCFM} SCFM ). For ACFM \text{ACFM} ACFM , use C s = 60 × ρ actual × 0.240 = 14.4 × ρ actual C_s = 60 \times \rho_{\text{actual}} \times 0.240 = 14.4 \times \rho_{\text{actual}} C s = 60 × ρ actual × 0.240 = 14.4 × ρ actual .
7. NCEES Reference Handbook Navigation Tactics
Weather Data Tables: Navigate to Section 6 (Psychrometrics) and Section 7 (HVAC & Refrigeration Applications) for the ASHRAE Climatic Design Conditions table. Look for columns labeled 0.4% DB/MCWB , 1.0% DB/MCWB , 99.6% Heating DB , and 0.4% Dew Point/MCDB .
Operative Temperature Equations: Search "Operative Temperature" to locate the simplified formula T o = ( T a + T ˉ r ) / 2 T_o = (T_a + \bar{T}_r)/2 T o = ( T a + T ˉ r ) /2 .
Altitude Properties: Search "Standard Atmosphere" or "Altitude Correction" to find barometric pressure versus elevation formulas and high-altitude psychrometric charts ( 5 , 000 ft 5,000\text{ ft} 5 , 000 ft and 7 , 500 ft 7,500\text{ ft} 7 , 500 ft ).
- 8. Worked Computational Examples
- Example 1: Climatic Design Percentile Selection & Frequency
A proposed critical surgical hospital in Atlanta, GA requires outdoor design conditions for its operating suites and central boiler plant. Using ASHRAE climatic data for Atlanta Hartsfield Airport:
0.4 % Cooling DB / MCWB = 94.2 ∘ F / 75.4 ∘ F 0.4\%\text{ Cooling DB / MCWB} = 94.2^\circ\text{F} / 75.4^\circ\text{F} 0.4% Cooling DB / MCWB = 94. 2 ∘ F /75. 4 ∘ F
1.0 % Cooling DB / MCWB = 91.8 ∘ F / 74.8 ∘ F 1.0\%\text{ Cooling DB / MCWB} = 91.8^\circ\text{F} / 74.8^\circ\text{F} 1.0% Cooling DB / MCWB = 91. 8 ∘ F /74. 8 ∘ F
- 99.6 % Heating DB = 21.4 ∘ F 99.6\%\text{ Heating DB} = 21.4^\circ\text{F} 99.6% Heating DB = 21. 4 ∘ F
- 99.0 % Heating DB = 25.6 ∘ F 99.0\%\text{ Heating DB} = 25.6^\circ\text{F} 99.0% Heating DB = 25. 6 ∘ F
Calculate: (a) The number of hours per year ambient dry-bulb exceeds the 0.4% condition versus the 1.0% condition, and (b) The heating design capacity increase percentage if sizing the building heating coil for 99.6% versus 99.0% with a 70 ∘ F 70^\circ\text{F} 7 0 ∘ F indoor setpoint.
Solution:
Annual exceedance hours: N 0.4 % = 8 , 760 × 0.004 = 35.04 hours/year N_{0.4\%} = 8,760 \times 0.004 = 35.04\text{ hours/year} N 0.4% = 8 , 760 × 0.004 = 35.04 hours/year N 1.0 % = 8 , 760 × 0.010 = 87.60 hours/year N_{1.0\%} = 8,760 \times 0.010 = 87.60\text{ hours/year} N 1.0% = 8 , 760 × 0.010 = 87.60 hours/year Δ N = 87.60 − 35.04 = 52.56 hours/year \Delta N = 87.60 - 35.04 = 52.56\text{ hours/year} Δ N = 87.60 − 35.04 = 52.56 hours/year
Heating temperature differentials ( T i = 70 ∘ F T_i = 70^\circ\text{F} T i = 7 0 ∘ F ): Δ T 99.6 % = 70 − 21.4 = 48.6 ∘ F \Delta T_{99.6\%} = 70 - 21.4 = 48.6^\circ\text{F} Δ T 99.6% = 70 − 21.4 = 48. 6 ∘ F Δ T 99.0 % = 70 − 25.6 = 44.4 ∘ F \Delta T_{99.0\%} = 70 - 25.6 = 44.4^\circ\text{F} Δ T 99.0% = 70 − 25.6 = 44. 4 ∘ F
Percentage capacity increase: Increase = 48.6 − 44.4 44.4 × 100 % = 4.2 44.4 × 100 % = 9.46 % \text{Increase} = \frac{48.6 - 44.4}{44.4} \times 100\% = \frac{4.2}{44.4} \times 100\% = 9.46\% Increase = 44.4 48.6 − 44.4 × 100% = 44.4 4.2 × 100% = 9.46%
Example 2: DOAS Dehumidification Coil Sizing (Peak DP vs Peak DB)
A 100% Dedicated Outdoor Air System (DOAS) supplies 5 , 000 CFM 5,000\text{ CFM} 5 , 000 CFM of outdoor air to an office building. The space is maintained at 75 ∘ F 75^\circ\text{F} 7 5 ∘ F DB and 50 % RH 50\%\text{ RH} 50% RH ( W space = 0.00925 lb w / lb d a W_{\text{space}} = 0.00925\text{ lb}_w/\text{lb}_{da} W space = 0.00925 lb w / lb d a ). The coil delivers supply air at 55 ∘ F 55^\circ\text{F} 5 5 ∘ F DB and 54 ∘ F 54^\circ\text{F} 5 4 ∘ F WB ( W supply = 0.00860 lb w / lb d a W_{\text{supply}} = 0.00860\text{ lb}_w/\text{lb}_{da} W supply = 0.00860 lb w / lb d a , h supply = 22.6 Btu/lb h_{\text{supply}} = 22.6\text{ Btu/lb} h supply = 22.6 Btu/lb ).
Compare the required total cooling coil capacity under two ambient weather conditions:
Case A (Peak DB 0.4%): 95 ∘ F 95^\circ\text{F} 9 5 ∘ F DB / 75 ∘ F 75^\circ\text{F} 7 5 ∘ F MCWB ( W = 0.01410 lb w / lb d a W = 0.01410\text{ lb}_w/\text{lb}_{da} W = 0.01410 lb w / lb d a , h = 38.6 Btu/lb h = 38.6\text{ Btu/lb} h = 38.6 Btu/lb )
Case B (Peak DP 0.4%): 82 ∘ F 82^\circ\text{F} 8 2 ∘ F DB / 76 ∘ F 76^\circ\text{F} 7 6 ∘ F DP ( W = 0.01950 lb w / lb d a W = 0.01950\text{ lb}_w/\text{lb}_{da} W = 0.01950 lb w / lb d a , h = 42.4 Btu/lb h = 42.4\text{ Btu/lb} h = 42.4 Btu/lb )
Solution:
Calculate total coil load for Case A (Peak Dry-Bulb): q total, A = 4.5 × CFM × ( h outdoor − h supply ) = 4.5 × 5 , 000 × ( 38.6 − 22.6 ) = 4.5 × 5 , 000 × 16.0 = 360 , 000 Btu/hr q_{\text{total, A}} = 4.5 \times \text{CFM} \times (h_{\text{outdoor}} - h_{\text{supply}}) = 4.5 \times 5,000 \times (38.6 - 22.6) = 4.5 \times 5,000 \times 16.0 = 360,000\text{ Btu/hr} q total, A = 4.5 × CFM × ( h outdoor − h supply ) = 4.5 × 5 , 000 × ( 38.6 − 22.6 ) = 4.5 × 5 , 000 × 16.0 = 360 , 000 Btu/hr Tonnage A = 360 , 000 12 , 000 = 30.0 Tons \text{Tonnage}_A = \frac{360,000}{12,000} = 30.0\text{ Tons} Tonnage A = 12 , 000 360 , 000 = 30.0 Tons
Calculate total coil load for Case B (Peak Dew-Point): q total, B = 4.5 × CFM × ( h outdoor − h supply ) = 4.5 × 5 , 000 × ( 42.4 − 22.6 ) = 4.5 × 5 , 000 × 19.8 = 445 , 500 Btu/hr q_{\text{total, B}} = 4.5 \times \text{CFM} \times (h_{\text{outdoor}} - h_{\text{supply}}) = 4.5 \times 5,000 \times (42.4 - 22.6) = 4.5 \times 5,000 \times 19.8 = 445,500\text{ Btu/hr} q total, B = 4.5 × CFM × ( h outdoor − h supply ) = 4.5 × 5 , 000 × ( 42.4 − 22.6 ) = 4.5 × 5 , 000 × 19.8 = 445 , 500 Btu/hr Tonnage B = 445 , 500 12 , 000 = 37.125 Tons \text{Tonnage}_B = \frac{445,500}{12,000} = 37.125\text{ Tons} Tonnage B = 12 , 000 445 , 500 = 37.125 Tons
Calculate moisture removal rate (latent load) difference: q latent, A = 4840 × 5 , 000 × ( 0.01410 − 0.00860 ) = 4840 × 5 , 000 × 0.00550 = 133 , 100 Btu/hr = 11.09 Tons q_{\text{latent, A}} = 4840 \times 5,000 \times (0.01410 - 0.00860) = 4840 \times 5,000 \times 0.00550 = 133,100\text{ Btu/hr} = 11.09\text{ Tons} q latent, A = 4840 × 5 , 000 × ( 0.01410 − 0.00860 ) = 4840 × 5 , 000 × 0.00550 = 133 , 100 Btu/hr = 11.09 Tons q latent, B = 4840 × 5 , 000 × ( 0.01950 − 0.00860 ) = 4840 × 5 , 000 × 0.01090 = 263 , 780 Btu/hr = 21.98 Tons q_{\text{latent, B}} = 4840 \times 5,000 \times (0.01950 - 0.00860) = 4840 \times 5,000 \times 0.01090 = 263,780\text{ Btu/hr} = 21.98\text{ Tons} q latent, B = 4840 × 5 , 000 × ( 0.01950 − 0.00860 ) = 4840 × 5 , 000 × 0.01090 = 263 , 780 Btu/hr = 21.98 Tons
Conclusion: Sizing the DOAS cooling coil for Peak DB (Case A) undersizes the dehumidification coil by 7.125 Tons 7.125\text{ Tons} 7.125 Tons (19.2% deficit in total capacity) and 10.89 Tons 10.89\text{ Tons} 10.89 Tons (49.5% deficit in moisture removal capacity) , causing severe space moisture buildup.